Search Results

Search found 6067 results on 243 pages for 'keyboard shortcut'.

Page 214/243 | < Previous Page | 210 211 212 213 214 215 216 217 218 219 220 221  | Next Page >

• USB drives not recognized all of a sudden (usb_storage not loaded lsmod does not report usb_storage)

  - by Siddharth

  I have tried most of the advice on askubuntu and other sites, usb_storage enable to fdisk -l. But I am unable to find steps to get it working again. sudo lsusb results Bus.... skipped 4 lines Bus 004 Device 002: ID 413c:3012 Dell Computer Corp. Optical Wheel Mouse Bus 005 Device 002: ID 413c:2105 Dell Computer Corp. Model L100 Keyboard Bus 001 Device 005: ID 8564:1000 sudo dmseg | tail reports [ 69.567948] usb 1-4: USB disconnect, device number 4 [ 74.084041] usb 1-6: new high-speed USB device number 5 using ehci_hcd [ 74.240484] Initializing USB Mass Storage driver... [ 74.256033] scsi5 : usb-storage 1-6:1.0 [ 74.256145] usbcore: registered new interface driver usb-storage [ 74.256147] USB Mass Storage support registered. [ 74.257290] usbcore: deregistering interface driver usb-storage fdisk -l reports Device Boot Start End Blocks Id System /dev/sda1 * 2048 972656639 486327296 83 Linux /dev/sda2 972658686 976771071 2056193 5 Extended /dev/sda5 972658688 976771071 2056192 82 Linux swap / Solaris I think I need steps to install and get usb_storage module working. Edit : I tried sudo modprobe -v usb-storage reports sudo modprobe -v usb-storage insmod /lib/modules/3.2.0-48-generic-pae/kernel/drivers/usb/storage/usb-storage.ko Edit : jsiddharth@siddharth-desktop:~$ sudo udevadm monitor --udev monitor will print the received events for: UDEV - the event which udev sends out after rule processing UDEV [4757.144372] add /module/usb_storage (module) UDEV [4757.146558] remove /module/usb_storage (module) UDEV [4757.148707] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6 (usb) UDEV [4757.149699] add /bus/usb/drivers/usb-storage (drivers) UDEV [4757.151214] remove /bus/usb/drivers/usb-storage (drivers) UDEV [4757.156873] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0 (usb) UDEV [4757.160903] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9 (scsi) UDEV [4757.164672] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9/scsi_host/host9 (scsi_host) UDEV [4757.165163] remove /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9/scsi_host/host9 (scsi_host) UDEV [4757.165440] remove /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9 (scsi) Narrowing down more : Seems like I need usb_storage to load as a module jsiddharth@siddharth-desktop:~$ lsmod | grep usb usbserial 37201 0 usbhid 41937 0 hid 77428 1 usbhid Still no usb driver mounted. Nor does a device show up in /dev. Any step by step process to debug and fix this will be really helpful.

  Read the article

• The Diabolical Developer: What You Need to Do to Become Awesome

  - by Tori Wieldt

  Wearing sunglasses and quite possibly hungover, Martijn Verburg's evil persona provided key tips on how to be a Diabolical Developer. His presentation at TheServerSide Java Symposium was heavy on the sarcasm and provided lots of laughter. Martijn insisted that developers take their power back and get rid of all the "modern fluff" that distract developers.He provided several key tips to become a Diabolical Developer:*Learn only from yourself. Don't read blogs or books, and don't attend conferences. If you must go on forums, only do it display your superiority, answer as obscurely as possible.*Work aloneBest coding happens when you alone in your room, lock yourself in for days. Make sure you have a gaming machine in with you.*Keep information to yourselfKnowledge is power. Think job security. Never provide documentation. *Make sure only you can read your code.Don't put comments in your code. Name your variables A,B,C....A1,B1, etc.If someone insists you format your in a standard way, change a small section and revert it back as soon as they walk away from your screen. *Stick to what you knowStay on Java 1.3. Don't bother learning abstractions. Write your application in a single file. Stuff as much code into one class as possible, a 30,000-line class is fine. Makes it easier for you to read and maintain.*Use Real ToolsNo "fancy-pancy" IDEs. Real developers only use vi.*Ignore FadsThe cloud is massively overhyped. Mobile is a big fad for young kids.The big, clunky desktop computer (with a real keyboard) will return.Learn new stuff only to pad your resume. Ajax is great for that. *Skip TestingTest-driven development is a complete waste of time. They sent men to the moon without unit tests.Just write your code properly in the first place and you don't need tests.*Compiled = Ship ItUser acceptance testing is an absolute waste of time. *Use a Single ThreadDon't use multithreading. All you need to do is throw more hardware at the problem.*Don't waste time on SEO.If you've written the contract correctly, you are paid for writing code, not attracting users.You don't want a lot of users, they only report problems. *Avoid meetingsFake being sick to avoid meetings. If you are forced into a meeting, play corporate bingo.Once you stand up and shout "bingo" you will kicked out of the meeting. Job done.Follow these tips and you'll be well on your way to being a Diabolical Developer!

  Read the article

• Integrating Windows Form Click Once Application into SharePoint 2007 &ndash; Part 2 of 4

  - by Kelly Jones

  In my last post, I explained why we decided to use a Click Once application to solve our business problem. To quickly review, we needed a way for our business users to upload documents to a SharePoint 2007 document library in mass, set the meta data, set the permissions per document, and to do so easily. Let’s look at the pieces that make up our solution.  First, we have the Windows Form application.  This app is deployed using Click Once and calls SharePoint web services in order to upload files and then calls web services to set the meta data (SharePoint columns and permissions).  Second, we have a custom action.  The custom action is responsible for providing our users a link that will launch the Windows app, as well as passing values to it via the query string.  And lastly, we have the web services that the Windows Form application calls.  For our solution, we used both out of the box web services and a custom web service in order to set the column values in the document library as well as the permissions on the documents. Now, let’s look at the technical details of each of these pieces.  (All of the code is downloadable from here: )   Windows Form application deployed via Click Once The Windows Form application, called “Custom Upload”, has just a few classes in it: Custom Upload -- the form FileList.xsd -- the dataset used to track the names of the files and their meta data values SharePointUpload -- this class handles uploading the file SharePointUpload uses an HttpWebRequest to transfer the file to the web server. We had to change this code from a WebClient object to the HttpWebRequest object, because we needed to be able to set the time out value.  public bool UploadDocument(string localFilename, string remoteFilename) { bool result = true; //Need to use an HttpWebRequest object instead of a WebClient object // so we can set the timeout (WebClient doesn't allow you to set the timeout!) HttpWebRequest req = (HttpWebRequest)WebRequest.Create(remoteFilename); try { req.Method = "PUT"; req.Timeout = 60 * 1000; //convert seconds to milliseconds req.AllowWriteStreamBuffering = true; req.Credentials = System.Net.CredentialCache.DefaultCredentials; req.SendChunked = false; req.KeepAlive = true; Stream reqStream = req.GetRequestStream(); FileStream rdr = new FileStream(localFilename, FileMode.Open, FileAccess.Read); byte[] inData = new byte[4096]; int bytesRead = rdr.Read(inData, 0, inData.Length); while (bytesRead > 0) { reqStream.Write(inData, 0, bytesRead); bytesRead = rdr.Read(inData, 0, inData.Length); } reqStream.Close(); rdr.Close(); System.Net.HttpWebResponse response = (HttpWebResponse)req.GetResponse(); if (response.StatusCode != HttpStatusCode.OK && response.StatusCode != HttpStatusCode.Created) { String msg = String.Format("An error occurred while uploading this file: {0}\n\nError response code: {1}", System.IO.Path.GetFileName(localFilename), response.StatusCode.ToString()); LogWarning(msg, "2ACFFCCA-59BA-40c8-A9AB-05FA3331D223"); result = false; } } catch (Exception ex) { LogException(ex, "{E9D62A93-D298-470d-A6BA-19AAB237978A}"); result = false; } return result; } The class also contains the LogException() and LogWarning() methods. When the application is launched, it parses the query string for some initial values.  The query string looks like this: string queryString = "Srv=clickonce&Sec=N&Doc=DMI&SiteName=&Speed=128000&Max=50"; This Srv is the path to the server (my Virtual Machine is name “clickonce”), the Sec is short for security – meaning HTTPS or HTTP, the Doc is the shortcut for which document library to use, and SiteName is the name of the SharePoint site.  Speed is used to calculate an estimate for download speed for each file.  We added this so our users uploading documents would realize how long it might take for clients in remote locations (using slow WAN connections) to download the documents. The last value, Max, is the maximum size that the SharePoint site will allow documents to be.  This allowed us to give users a warning that a file is too large before we even attempt to upload it. Another critical piece is the meta data collection.  We organized our site using SharePoint content types, so when the app loads, it gets a list of the document library’s content types.  The user then select one of the content types from the drop down list, and then we query SharePoint to get a list of the fields that make up that content type.  We used both an out of the box web service, and one that we custom built, in order to get these values. Once we have the content type fields, we then add controls to the form.  Which type of control we add depends on the data type of the field.  (DateTime pickers for date/time fields, etc)  We didn’t write code to cover every data type, since we were working with a limited set of content types and field data types. Here’s a screen shot of the Form, before and after someone has selected the content types and our code has added the custom controls:     The other piece of meta data we collect is the in the upper right corner of the app, “Users with access”.  This box lists the different SharePoint Groups that we have set up and by checking the boxes, the user can set the permissions on the uploaded documents. All of this meta data is collected and submitted to our custom web service, which then sets the values on the documents on the list.  We’ll look at these web services in a future post. In the next post, we’ll walk through the Custom Action we built.

  Read the article

• Box2D Bicycle Wheels Motor Problem - Flash 2.1a

  - by Craig

  I have made a bicycle with Box2D using several polygons for the frame at different angles connected using weld joints, and I have revolute joints on the wheels with a motor. I have made some basic terrain (straight ground and a small ramp) and added keyboard input to control the bicycle with torque to balance it. All of this is done in with Box2D's Debug Draw. When the bicycle is on its back wheel but diagonally forward (kinda like this position - /) the motors just cause it go spinning backwards over when in reality it should either stay on its back wheel or go down onto both wheels. Here's my code the revolute joints: //Front Wheel Joint var frontWheelJointDef:b2RevoluteJointDef = new b2RevoluteJointDef(); frontWheelJointDef.Initialize(frontWheelBody, secondFrameBody, frontWheelBody.GetWorldCenter()); frontWheelJointDef.enableMotor=true; frontWheelJointDef.maxMotorTorque=10000; frontWheelJoint = _world.CreateJoint(frontWheelJointDef) as b2RevoluteJoint; //Rear Wheel Joint var rearWheelJointDef:b2RevoluteJointDef = new b2RevoluteJointDef(); rearWheelJointDef.Initialize(rearWheelBody, firstFrameBody, rearWheelBody.GetWorldCenter()); rearWheelJointDef.enableMotor=true; rearWheelJointDef.maxMotorTorque=10000; rearWheelJoint = _world.CreateJoint(rearWheelJointDef) as b2RevoluteJoint; And here's the relevant part of my update function: // up and down control wheels motor if (up) { motorSpeed-=0.5; } if (down) { motorSpeed += 0.5; } // left and right control cart torque if (left) { middleCentreFrameBody.ApplyTorque( -3); gearBody.ApplyTorque( -3); firstFrameBody.ApplyTorque( -3); secondFrameBody.ApplyTorque( -3); rearWheelToChainBody.ApplyTorque( -3); chainToFrontFrameBody.ApplyTorque( -3); topMiddleFrameBody.ApplyTorque( -3); } if (right) { middleCentreFrameBody.ApplyTorque( 3); gearBody.ApplyTorque( 3); firstFrameBody.ApplyTorque( 3); secondFrameBody.ApplyTorque( 3); rearWheelToChainBody.ApplyTorque( 3); chainToFrontFrameBody.ApplyTorque( 3); topMiddleFrameBody.ApplyTorque( 3); } // motor friction motorSpeed*=0.99; // motor max speed if (motorSpeed>100) { motorSpeed=100; } rearWheelJoint.SetMotorSpeed(motorSpeed); frontWheelJoint.SetMotorSpeed(motorSpeed); Any ideas what might be causing this? Thanks

  Read the article

• Win7 is not a tablet OS, no matter what the boys in Redmond think.

  - by John Conwell

  Despite what execs at Microsoft think, Windows 7 is NOT a tablet OS.  Just because you can install some software (or OS) on a device, doesn't mean that device is meant to run that software.  This seems to be the step that the non-engineer execs at Microsoft have seem to not understood.  In order to seamlessly work with a device, the software needs to be designed with that device in mind.  That has been the problem with the Windows PDA platform, the Windows Mobil platform, and now with trying to force fit Windows 7 on a tablet.  Its just not designed for that style of interaction.   Windows is designed to be interacted with via a mouse and keyboard.  In fact, it is brilliant at that.  But, It is NOT designed to be interacted with by your fingers.  And that is why the Windows tablet failed 10 years ago, and why it will fail today.  Its not the hardware's fault like Microsoft claimed 10 years ago.  Its the User Interaction design that failed. And this is why the iPhone and Android OS's work wonderfully on a tablet.  The user interaction was designed for small screens, navigated by big fat fingers.  I love these OS's and how I interact with them.  And when I play with a touch screen Windows 7 device, I am feel like I'm playing with a brittle wana-be.  And its not the hardware's fault.  The touchscreen is very responsive.  I actually like the hardware.  But the OS and the software are just not designed to be interacted with, with my big fat fingers.  In order to be successful, Microsoft needs to start from scratch, and build a platform AND SOFTWARE specifically for use by fingers.  Thats why everyone was so excited when they though Microsoft was going to release the Courier tablet.  Because it looked like a totally different platform.  Something that might actually work.  But Windows 7...I hate to burst your bubble, but you are not a touch platform.

  Read the article

• Friday Fun: Play Your Favorite 8-Bit NES Games Online

  - by Mysticgeek

  We finally made it to another Friday and once again we bring you some NES fun to waste the rest of the day before the weekend. Today we take a look at a site that contains a lot of classic NES games you can play online. vNES VirtualNES.com contains hundreds of vintage NES games you can play online. If you’re old enough to remember, when the NES came out, it breathed life back into home console gaming. Here we will take a look at a few of the games they offer that will certainly bring back memories. Super Mario Bros 3 which is a personal favorite from the 8-bit era.   Play Super Mario Bros 3 Excite Bike was one of the coolest dirt bike racing games at the time as it even allowed you to create your own tracks.   Play ExciteBike Of course The Legend of Zelda was one of the first fantasy games many an hour have been spent on. Play The Legend of Zelda We’d be remiss if we didn’t bring up Pac-man since the game recently celebrated it’s 30th anniversary. Play Pac-Man If you don’t like the default keyboard controls you can change them on the Options page. Join their forum and more…this site will definitely bring you back to the good old 8-bit NES days.   The site contains hundreds of different games for you to get on your old school NES fix. If you’re sick of waiting for the whistle to blow, this site will bring you back to the good old days when you had nothing to do but mash buttons all day. Play NES Games at virtualnes.com Similar Articles Productive Geek Tips Friday Fun: Get Your Mario OnFriday Fun: Go Retro with PacmanFriday Fun: Five More Time Wasting Online GamesFriday Fun: Online Flash Games to Usher in the WeekendFriday Fun: Online Sports Flash Games TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips HippoRemote Pro 2.2 Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Awesome World Cup Soccer Calendar Nice Websites To Watch TV Shows Online 24 Million Sites Windows Media Player Glass Icons (icons we like) How to Forecast Weather, without Gadgets Outlook Tools, one stop tweaking for any Outlook version

  Read the article

• Desktop Fun: Happy New Year Wallpaper Collection [Bonus Edition]

  - by Asian Angel

  As this year draws to a close, it is a time to reflect back on what we have done this year and to look forward to the new one. To help commemorate the event we have put together a bonus size edition of Happy New Year wallpapers for your desktops. Extra Note: We made a special effort to find wallpapers for this collection without the year “printed” on them, thus allowing for reuse as desired and/or needed beyond the 2010 – 2011 holiday. Note: Click on the picture to see the full-size image—these wallpapers vary in size so you may need to crop, stretch, or place them on a colored background in order to best match them to your screen’s resolution. For more New Year’s desktop goodness be sure to check out our Happy New Year icon & font packs collection (link at bottom)! Note: This wallpaper will need to be placed on a larger white background in order to increase the height. Note: This wallpaper will need to be placed on a larger background in order to increase the width and height. Note: This wallpaper comes in multiple sizes and will need to be downloaded as a zip file. Note: This wallpaper comes in multiple sizes and will need to be downloaded as a zip file. Note: The download size for the original version of this wallpaper is 15 MB. Note: The download size for the original version of this wallpaper is 15 MB. More Happy New Year Fun Desktop Fun: Happy New Year Icon and Font Packs For more wallpapers be certain to see our great collections in the Desktop Fun section. Latest Features How-To Geek ETC How to Use the Avira Rescue CD to Clean Your Infected PC The Complete List of iPad Tips, Tricks, and Tutorials Is Your Desktop Printer More Expensive Than Printing Services? 20 OS X Keyboard Shortcuts You Might Not Know HTG Explains: Which Linux File System Should You Choose? HTG Explains: Why Does Photo Paper Improve Print Quality? The Outdoor Lights Scene from National Lampoon’s Christmas Vacation [Video] The Famous Home Alone Pizza Delivery Scene [Classic Video] Chronicles of Narnia: The Voyage of the Dawn Treader Theme for Windows 7 Cardinal and Rabbit Sharing a Tree on a Cold Winter Morning Wallpaper An Alternate Star Wars Christmas Special [Video] Sunset in a Tropical Paradise Wallpaper

  Read the article

• Ubuntu 12.10 Trackpoint not detected Thinkpad X130e

  - by killerknives

  I just did a fresh install of 12.10 and now only my touchpad works. The trackpoint and Left/Right buttons below the trackpoint do not work. The trackpoint worked fine as of 12.04. I've searched online and there was a hack that said that disabling the touchpad would enable the trackpoint. WRONG! You'll end up having to use the keyboard =/. I don't know what is needed so I'll just dump some stuff. lspci: 00:00.0 Host bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Complex 00:01.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Wrestler [Radeon HD 6310] 00:01.1 Audio device: Advanced Micro Devices [AMD] nee ATI Wrestler HDMI Audio [Radeon HD 6250/6310] 00:05.0 PCI bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Port 00:06.0 PCI bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Port 00:07.0 PCI bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Port 00:11.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] 00:12.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:12.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 42) 00:14.2 Audio device: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) (rev 40) 00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 LPC host controller (rev 40) 00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge (rev 40) 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 0 (rev 43) 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 1 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 2 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 3 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 4 00:18.5 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 6 00:18.6 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 5 00:18.7 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 7 01:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) 02:00.0 Ethernet controller: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet (rev c0) I've installged gpointing-device-setting and it only lists the touchpad. No trackpoint. What should I do? What data do you need?

  Read the article

• Friday Fun: Snowball

  - by Asian Angel

  It is Christmas Eve and hopefully you are enjoying the start of an early weekend away from work. This week we have a snowball throwing game for you to try out, so bundle up and get ready to let those snowballs fly! Snowball The object of the game is to use your snowball ammo to harass the drunk businessman and send him flying along distance-wise as far as you can. Simply use your mouse to aim and click the left button to throw snowballs. You can monitor your stats on the silver bar towards the top of the window. The sound can also be disabled if the music is bothering you, but keep in mind that all sound will be disabled if you use the option. Time to get those snowballs flying through the air!! Keep hitting the businessman with your snowballs as you chase after him. Make certain that your aim is good or you will quickly run out of snowballs! You can really get him moving along at a good rate and he can even go high enough in the air to disappear off the screen for a few moments. There is a also chance that your aim will be so wicked with the snowballs that you will literally knock the drunk businessman’s head off! Weird but possible… The game ends when one of these two events occur: 1.) you run out of snowballs or 2.) the businessman literally bounces back at and then drops behind you as seen in the screenshot here. The moment either happens your score will pop up and then you have the opportunity to try again. Have fun! Note: The bounce back event can happen when encountering cars. Play Snowball Latest Features How-To Geek ETC How to Use the Avira Rescue CD to Clean Your Infected PC The Complete List of iPad Tips, Tricks, and Tutorials Is Your Desktop Printer More Expensive Than Printing Services? 20 OS X Keyboard Shortcuts You Might Not Know HTG Explains: Which Linux File System Should You Choose? HTG Explains: Why Does Photo Paper Improve Print Quality? An Alternate Star Wars Christmas Special [Video] Sunset in a Tropical Paradise Wallpaper Natural Wood Grain Icons for Your Desktop and App Launcher Docks My Blackberry Is Not Working! The Apple Too?! [Funny Video] Hidden Tracks Your Stolen Mac; Free Until End of January Why the Other Checkout Line Always Moves Faster

  Read the article

• Why learn Flash Builder 4 (Flex) when I can just use Flash Professional?

  - by Jason McKenna

  I want to learn Flash Builder 4 (Flex) because I see so many jobs requesting experience with it. I also just like knowing stuff. I am also very interested in focusing on RIA development now. BUT... can anyone tell me CLEARLY why the heck I would ever use FLEX over Flash Pro? It is a time investment, so is it worth it? All I read are misguided posts about how Flash Pro is for games and banner ads, and Flex is for programmers and RIAs blah blah... this simply isn't so from my 9 years of contracting experience. I'm 99.9% certain that I can build anything a flex developer can build, but using Flash Pro. I can build powerful AS3-driven apps for the desktop, mobile device, or browser, and I can link to databases with XML and I can import text files and communicate with ColdFusion and everything. The advantage with Flash Pro is that I can also easily and clearly animate transitions and build custom elements that look the way I want/need them to look for my specific client. Why would I want to use a bunch of pre-built components that drive my file sizes to the moon? Who is happy with a drag-n-drop button? Is Flex just a thing made for programmer people with no artistic inclination? What is the advantage of using it? It takes me back to Visual Basic class. Seems like a pain to have to use multiple tools to import crap from Flash Pro into Flex and yada yada... why when I can do it all nicely in Flash Pro to begin with. Am I clueless, or missing some major piece of the puzzle? Thanks for any clarity. PS, I couldn't care less about the code editors. It ain't that bad people. They make it out like the thing doesn't even respond to keyboard input or something. Does everything I need it do anyways. Please help out here. If I just don't need to learn it, I don't want to waste the time.

  Read the article

• Xorg.conf (nvidia) Second Monitor getting settings of first

  - by HennyH

  I've been spending the weekend (and some time before that) trying to set up my Korean QHD270 and Benq G2222HDL monitors with Ubuntu 13.10. With the nouveau drivers install both monitor function perfectly fine. After installing the nvidia drivers the Benq works but the QHD270 does not. Now, after days of struggling I managed to get the QHD270 to work following a mixture of blogs, particularly; this one and learnitwithme. Now, unfortunatly my G2222HDL does not work. I fixed the QHD270 by supplying a custom EDID, my xorg.conf looks like so (excluding keyboard and mouse): Section "ServerLayout" Identifier "Layout0" Screen "Default Screen" 0 0 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" EndSection Section "Monitor" Identifier "Configured Monitor" EndSection Section "Device" Identifier "Configured Video Device" Driver "nvidia" Option "CustomEDID" "DFP:/etc/X11/edid-shimian.bin" EndSection Section "Screen" Identifier "Default Screen" Device "Configured Video Device" Monitor "Configured Monitor" EndSection Now, I tried defining a new Device,Monitor and Screen then in ServerLayout adding Screen "Second Screen" RightOf "Default Screen", but after doing so neither monitor worked. Hoping to fix the issue using a GUI based tool I opened up NVIDIA X Server Settings, which shows my current layout as: It seems that something is being output to the monitor, as suggested by my print screen: Any help would be greatly appreciated. Output of xrandr: Screen 0: minimum 8 x 8, current 5120 x 1440, maximum 16384 x 16384 DVI-I-0 disconnected (normal left inverted right x axis y axis) DVI-I-1 connected primary 2560x1440+0+0 (normal left inverted right x axis y axis) 597mm x 336mm 2560x1440 60.0*+ HDMI-0 disconnected (normal left inverted right x axis y axis) DP-0 disconnected (normal left inverted right x axis y axis) DVI-D-0 connected 2560x1440+2560+0 (normal left inverted right x axis y axis) 597mm x 336mm 2560x1440 60.0*+ DP-1 disconnected (normal left inverted right x axis y axis) And an extract from my log file (perhaps this is relevant?) [ 7.862] (--) NVIDIA(0): Valid display device(s) on GeForce GTX 680 at PCI:2:0:0 [ 7.862] (--) NVIDIA(0): CRT-0 [ 7.862] (--) NVIDIA(0): ACB QHD270 (DFP-0) (boot, connected) [ 7.862] (--) NVIDIA(0): DFP-1 [ 7.862] (--) NVIDIA(0): DFP-2 [ 7.862] (--) NVIDIA(0): DFP-3 [ 7.862] (--) NVIDIA(0): DFP-4 [ 7.862] (--) NVIDIA(0): CRT-0: 400.0 MHz maximum pixel clock [ 7.862] (--) NVIDIA(0): ACB QHD270 (DFP-0): 330.0 MHz maximum pixel clock [ 7.862] (--) NVIDIA(0): ACB QHD270 (DFP-0): Internal Dual Link TMDS [ 7.862] (--) NVIDIA(0): DFP-1: 165.0 MHz maximum pixel clock [ 7.862] (--) NVIDIA(0): DFP-1: Internal Single Link TMDS [ 7.862] (--) NVIDIA(0): DFP-2: 165.0 MHz maximum pixel clock [ 7.862] (--) NVIDIA(0): DFP-2: Internal Single Link TMDS [ 7.862] (--) NVIDIA(0): DFP-3: 330.0 MHz maximum pixel clock [ 7.862] (--) NVIDIA(0): DFP-3: Internal Single Link TMDS [ 7.862] (--) NVIDIA(0): DFP-4: 960.0 MHz maximum pixel clock [ 7.862] (--) NVIDIA(0): DFP-4: Internal DisplayPort

  Read the article

• What can a Service do on Windows?

  - by Akemi Iwaya

  If you open up Task Manager or Process Explorer on your system, you will see many services running. But how much of an impact can a service have on your system, especially if it is ‘corrupted’ by malware? Today’s SuperUser Q&A post has the answers to a curious reader’s questions. Today’s Question & Answer session comes to us courtesy of SuperUser—a subdivision of Stack Exchange, a community-driven grouping of Q&A web sites. The Question SuperUser reader Forivin wants to know how much impact a service can have on a Windows system, especially if it is ‘corrupted’ by malware: What kind malware/spyware could someone put into a service that does not have its own process on Windows? I mean services that use svchost.exe for example, like this: Could a service spy on my keyboard input? Take screenshots? Send and/or receive data over the internet? Infect other processes or files? Delete files? Kill processes? How much impact could a service have on a Windows installation? Are there any limits to what a malware ‘corrupted’ service could do? The Answer SuperUser contributor Keltari has the answer for us: What is a service? A service is an application, no more, no less. The advantage is that a service can run without a user session. This allows things like databases, backups, the ability to login, etc. to run when needed and without a user logged in. What is svchost? According to Microsoft: “svchost.exe is a generic host process name for services that run from dynamic-link libraries”. Could we have that in English please? Some time ago, Microsoft started moving all of the functionality from internal Windows services into .dll files instead of .exe files. From a programming perspective, this makes more sense for reusability…but the problem is that you can not launch a .dll file directly from Windows, it has to be loaded up from a running executable (exe). Thus the svchost.exe process was born. So, essentially a service which uses svchost is just calling a .dll and can do pretty much anything with the right credentials and/or permissions. If I remember correctly, there are viruses and other malware that do hide behind the svchost process, or name the executable svchost.exe to avoid detection. Have something to add to the explanation? Sound off in the comments. Want to read more answers from other tech-savvy Stack Exchange users? Check out the full discussion thread here.

  Read the article

• GPU hung when switching graphic card

  - by Lie Ryan

  I have a laptop (Dell Inspiron N4110) with a switchable graphic. $ lspci | grep VGA 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 01:00.0 VGA compatible controller: ATI Technologies Inc NI Whistler [AMD Radeon HD 6600M Series] (rev ff) Normally, my laptop starts with both graphic cards enabled, which caused the laptop to turn very hot and the fan to become very noisy. I have been using a small script to disable the Radeon card. For some time, I'm quite happy with this arrangement. However, I have been having some issues with the Intel card (IGD), the Intel card often randomly hang when running OpenGL apps; and so I want to give the Radeon card (DIS) another chance. I have never been able to switch to the Radeon card, but recently, I found out that if I do a "delayed switching" (DDIS): # echo "DDIS" > /sys/kernel/debug/vgaswitcheroo/switch root@lieryan-dell-ubuntu:/sys/kernel/debug/vgaswitcheroo# cat switch 0:IGD:+:Pwr:0000:00:02.0 1:DIS: :Pwr:0000:01:00.0 then I logoff (i.e. to restart X), the screen switch to pseudo-tty and then it stuck there freezing. At this situation, mouse and keyboard stops working so I can't switch to another ptty. I tried ssh-ing from another computer to salvage logs (dmesg at that point) and whatnot; I found out that when freezing, the active graphic card is the AMD card: -- this is from ssh -- # cat switch 0:IGD: :Off:0000:00:02.0 1:DIS:+:Pwr:0000:01:00.0 but the GPU is apparently hung, looking at dmesg gives: ... [ 1411.649974] vga_switcheroo: client 0 refused switch [ 1411.649985] vga_switcheroo: setting delayed switch to client 1 [ 1423.911759] vga_switcheroo: processing delayed switch to 1 [ 1424.006564] fbcon: Remapping primary device, fb1, to tty 1-63 [ 1424.006799] i915: switched off [ 1424.840351] [drm:drm_mode_getfb] *ERROR* invalid framebuffer id [ 1425.718088] [drm:drm_mode_getfb] *ERROR* invalid framebuffer id [ 1426.622377] [drm:drm_mode_getfb] *ERROR* invalid framebuffer id [ 1427.355683] [drm:drm_mode_getfb] *ERROR* invalid framebuffer id [ 1428.193549] [drm:drm_mode_getfb] *ERROR* invalid framebuffer id ... the invalid framebuffer id error is repeated for many times over ... I were able to successfully recover by switching back to the Intel card and restarting X from ssh; indicating that only the Radeon card has problems switching. System info: $ uname -a Linux lieryan-dell-ubuntu 3.0.0-14-generic #23-Ubuntu SMP Mon Nov 21 20:28:43 UTC 2011 x86_64 x86_64 x86_64 GNU/Linux $ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 11.10 Release: 11.10 Codename: oneiric The laptop also do not have the option to set graphic card at BIOS and the proprietary driver, fglrx, also have never worked; when I installed it through jockey ("Additional Drivers"), glxinfo showed that it still being rendered by Mesa, the /sys/kernel/debug/vgaswitcheroo directory has gone missing, and the driver crashes with a traceback if I use xorg.conf to tell X to use fglrx. Anyone had any idea if it is possible to use this AMD card either with the radeon or the fglrx driver? logs: dmesg

  Read the article

• Which of these algorithms is best for my goal?

  - by JonathonG

  I have created a program that restricts the mouse to a certain region based on a black/white bitmap. The program is 100% functional as-is, but uses an inaccurate, albeit fast, algorithm for repositioning the mouse when it strays outside the area. Currently, when the mouse moves outside the area, basically what happens is this: A line is drawn between a pre-defined static point inside the region and the mouse's new position. The point where that line intersects the edge of the allowed area is found. The mouse is moved to that point. This works, but only works perfectly for a perfect circle with the pre-defined point set in the exact center. Unfortunately, this will never be the case. The application will be used with a variety of rectangles and irregular, amorphous shapes. On such shapes, the point where the line drawn intersects the edge will usually not be the closest point on the shape to the mouse. I need to create a new algorithm that finds the closest point to the mouse's new position on the edge of the allowed area. I have several ideas about this, but I am not sure of their validity, in that they may have far too much overhead. While I am not asking for code, it might help to know that I am using Objective C / Cocoa, developing for OS X, as I feel the language being used might affect the efficiency of potential methods. My ideas are: Using a bit of trigonometry to project lines would work, but that would require some kind of intense algorithm to test every point on every line until it found the edge of the region... That seems too resource intensive since there could be something like 200 lines that would have each have to have as many as 200 pixels checked for black/white.... Using something like an A* pathing algorithm to find the shortest path to a black pixel; however, A* seems resource intensive, even though I could probably restrict it to only checking roughly in one direction. It also seems like it will take more time and effort than I have available to spend on this small portion of the much larger project I am working on, correct me if I am wrong and it would not be a significant amount of code (100 lines or around there). Mapping the border of the region before the application begins running the event tap loop. I think I could accomplish this by using my current line-based algorithm to find an edge point and then initiating an algorithm that checks all 8 pixels around that pixel, finds the next border pixel in one direction, and continues to do this until it comes back to the starting pixel. I could then store that data in an array to be used for the entire duration of the program, and have the mouse re-positioning method check the array for the closest pixel on the border to the mouse target position. That last method would presumably execute it's initial border mapping fairly quickly. (It would only have to map between 2,000 and 8,000 pixels, which means 8,000 to 64,000 checked, and I could even permanently store the data to make launching faster.) However, I am uncertain as to how much overhead it would take to scan through that array for the shortest distance for every single mouse move event... I suppose there could be a shortcut to restrict the number of elements in the array that will be checked to a variable number starting with the intersecting point on the line (from my original algorithm), and raise/lower that number to experiment with the overhead/accuracy tradeoff. Please let me know if I am over thinking this and there is an easier way that will work just fine, or which of these methods would be able to execute something like 30 times per second to keep mouse movement smooth, or if you have a better/faster method. I've posted relevant parts of my code below for reference, and included an example of what the area might look like. (I check for color value against a loaded bitmap that is black/white.) // // This part of my code runs every single time the mouse moves. // CGPoint point = CGEventGetLocation(event); float tX = point.x; float tY = point.y; if( is_in_area(tX,tY, mouse_mask)){ // target is inside O.K. area, do nothing }else{ CGPoint target; //point inside restricted region: float iX = 600; // inside x float iY = 500; // inside y // delta to midpoint between iX,iY and tX,tY float dX; float dY; float accuracy = .5; //accuracy to loop until reached do { dX = (tX-iX)/2; dY = (tY-iY)/2; if(is_in_area((tX-dX),(tY-dY),mouse_mask)){ iX += dX; iY += dY; } else { tX -= dX; tY -= dY; } } while (abs(dX)>accuracy || abs(dY)>accuracy); target = CGPointMake(roundf(tX), roundf(tY)); CGDisplayMoveCursorToPoint(CGMainDisplayID(),target); } Here is "is_in_area(int x, int y)" : bool is_in_area(NSInteger x, NSInteger y, NSBitmapImageRep *mouse_mask){ NSAutoreleasePool * pool = [[NSAutoreleasePool alloc] init]; NSUInteger pixel[4]; [mouse_mask getPixel:pixel atX:x y:y]; if(pixel[0]!= 0){ [pool release]; return false; } [pool release]; return true; }

  Read the article

• Are You an IT Geek? Why Not Write for How-To Geek?

  - by The Geek

  Are you a geek in the IT field that wants to share your skills with the world? We’re looking for an experienced Sysadmin / IT Admin / Webmaster geek with writing skills that wants to join our team on a part-time basis. Please apply if you have the following qualities: You must be a geek at heart, willing to try and make the boring world of IT sound glamorous and sexy. If that’s not possible, at least be willing to share your wisdom and skills to help other IT geeks save time and become better at what they do. You must be able to write articles that are easy to understand. Either Windows or Linux writers are welcome to apply. You must be able to follow our style guide. You must be creative. You must generate ideas for articles on your own, and take suggestions like a pro. You’re ambitious, looking to build your skills and your name, and are prepared to work hard. If you aren’t willing to work hard, put some dedication and pride into your work, or aren’t really interested in the topic, this job might not be for you. We’re looking for serious individuals that want to grow with us, and as we grow, you’ll grow as well. How To Apply If you think this job is a good fit for you, send an email to [email protected] and include some background information about yourself, why you’d be a good fit, some topic areas you are familiar with, and hopefully some examples of your work. Bonus points if you have a ninja costume and a keyboard strapped to your back. Similar Articles Productive Geek Tips What Topics Should The How-To Geek Write About?Got Awesome Skills? Why Not Write for How-To Geek?Got Awesome Geek Skills? The How-To Geek is Looking for WritersAbout the GeekThe How-To Geek Bounty Program TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 QuicklyCode Provides Cheatsheets & Other Programming Stuff Download Free MP3s from Amazon Awe inspiring, inter-galactic theme (Win 7) Case Study – How to Optimize Popular Wordpress Sites Restore Hidden Updates in Windows 7 & Vista Iceland an Insurance Job?

  Read the article

• New computer hangs on shutdown/reboot, how to troubleshoot?

  - by torbengb

  Summary: My machine hangs on shutdown/restart: all windows and the menu bar disappear but the desktop wallpaper remains, and it stays like that without disk activity forever (hours). It doesn't even show the shutdown screen (the one with the animated dots) where I could hit ESC and watch the shutdown text. How can I troubleshoot this? Details: I've just received a new nettop computer (Acer Aspire Revo 3700: CPU:Atom D525, GPU:Nvidia ION2). I've just made a clean install of Ubuntu 10.10 using the standard USB pendrive method. The machine boots okay and works OK including WLAN and audio, but the graphics are not OK. Ubuntu offered to install&activate the current recommended Nvidia driver, but the machine hangs on shutdown/restart which prevents the installation of the proper Nvidia driver. I have to cycle the power to reboot. I ran the Update Manager in the hope that the updates would fix the hang-up. At the end of the update-installation it asked to reboot - and got stuck just like before. I see no obvious cause of the freeze and I don't know if it's caused by graphics problems or anything else. The only USB attachment is a mouse/keyboard; I don't have any external storage attached; and I don't have any programs running (the machine freezes even when doing restart right after login). How can I determine what is causing the freeze? How can I fix this? I'm frankly rather disappointed because I bought this new machine in the hopes of getting the graphics to work, which failed miserably on my old machine, even though Ubuntu is supposed to be good with Nvidia. Being a fresh convert from Windows, I was hoping for a happier experience this time, so I'm very much looking forward to your suggestions! ... After posting this question, I see related questions in the right sidebar: this, this, and this. Don't know why these didn't show up while I composed by question. Those questions suggest some ACPI settings but I am not experienced enough to find/change those settings. I'll try the sudo shutdown -h now command when I get home and see if that works, then update this question. I did check the system BIOS but didn't see anything out of the ordinary.

  Read the article

• Migrating Core Data to new UIManagedDocument in iOS 5

  - by samerpaul

  I have an app that has been on the store since iOS 3.1, so there is a large install base out there that still uses Core Data loaded up in my AppDelegate. In the most recent set of updates, I raised the minimum version to 4.3 but still kept the same way of loading the data. Recently, I decided it's time to make the minimum version 5.1 (especially with 6 around the corner), so I wanted to start using the new fancy UIManagedDocument way of using Core Data. The issue with this though is that the old database file is still sitting in the iOS app, so there is no migrating to the new document. You have to basically subclass UIManagedDocument with a new model class, and override a couple of methods to do it for you. Here's a tutorial on what I did for my app TimeTag.  Step One: Add a new class file in Xcode and subclass "UIManagedDocument" Go ahead and also add a method to get the managedObjectModel out of this class. It should look like:   @interface TimeTagModel : UIManagedDocument   - (NSManagedObjectModel *)managedObjectModel;   @end   Step two: Writing the methods in the implementation file (.m) I first added a shortcut method for the applicationsDocumentDirectory, which returns the URL of the app directory.  - (NSURL *)applicationDocumentsDirectory {     return [[[NSFileManagerdefaultManager] URLsForDirectory:NSDocumentDirectoryinDomains:NSUserDomainMask] lastObject]; }   The next step was to pull the managedObjectModel file itself (.momd file). In my project, it's called "minimalTime". - (NSManagedObjectModel *)managedObjectModel {     NSString *path = [[NSBundlemainBundle] pathForResource:@"minimalTime"ofType:@"momd"];     NSURL *momURL = [NSURL fileURLWithPath:path];     NSManagedObjectModel *managedObjectModel = [[NSManagedObjectModel alloc] initWithContentsOfURL:momURL];          return managedObjectModel; }   After that, I need to check for a legacy installation and migrate it to the new UIManagedDocument file instead. This is the overridden method: - (BOOL)configurePersistentStoreCoordinatorForURL:(NSURL *)storeURL ofType:(NSString *)fileType modelConfiguration:(NSString *)configuration storeOptions:(NSDictionary *)storeOptions error:(NSError **)error {     // If legacy store exists, copy it to the new location     NSURL *legacyPersistentStoreURL = [[self applicationDocumentsDirectory] URLByAppendingPathComponent:@"minimalTime.sqlite"];          NSFileManager* fileManager = [NSFileManagerdefaultManager];     if ([fileManager fileExistsAtPath:legacyPersistentStoreURL.path])     {         NSLog(@"Old db exists");         NSError* thisError = nil;         [fileManager replaceItemAtURL:storeURL withItemAtURL:legacyPersistentStoreURL backupItemName:niloptions:NSFileManagerItemReplacementUsingNewMetadataOnlyresultingItemURL:nilerror:&thisError];     }          return [superconfigurePersistentStoreCoordinatorForURL:storeURL ofType:fileType modelConfiguration:configuration storeOptions:storeOptions error:error]; }   Basically what's happening above is that it checks for the minimalTime.sqlite file inside the app's bundle on the iOS device.  If the file exists, it tells you inside the console, and then tells the fileManager to replace the storeURL (inside the method parameter) with the legacy URL. This basically gives your app access to all the existing data the user has generated (otherwise they would load into a blank app, which would be disastrous). It returns a YES if successful (by calling it's [super] method). Final step: Actually load this database Due to how my app works, I actually have to load the database at launch (instead of shortly after, which would be ideal). I call a method called loadDatabase, which looks like this: -(void)loadDatabase {     static dispatch_once_t onceToken;          // Only do this once!     dispatch_once(&onceToken, ^{         // Get the URL         // The minimalTimeDB name is just something I call it         NSURL *url = [[selfapplicationDocumentsDirectory] URLByAppendingPathComponent:@"minimalTimeDB"];         // Init the TimeTagModel (our custom class we wrote above) with the URL         self.timeTagDB = [[TimeTagModel alloc] initWithFileURL:url];           // Setup the undo manager if it's nil         if (self.timeTagDB.undoManager == nil){             NSUndoManager *undoManager = [[NSUndoManager  alloc] init];             [self.timeTagDB setUndoManager:undoManager];         }                  // You have to actually check to see if it exists already (for some reason you can't just call "open it, and if it's not there, create it")         if ([[NSFileManagerdefaultManager] fileExistsAtPath:[url path]]) {             // If it does exist, try to open it, and if it doesn't open, let the user (or at least you) know!             [self.timeTagDB openWithCompletionHandler:^(BOOL success){                 if (!success) {                     // Handle the error.                     NSLog(@"Error opening up the database");                 }                 else{                     NSLog(@"Opened the file--it already existed");                     [self refreshData];                 }             }];         }         else {             // If it doesn't exist, you need to attempt to create it             [self.timeTagDBsaveToURL:url forSaveOperation:UIDocumentSaveForCreatingcompletionHandler:^(BOOL success){                 if (!success) {                     // Handle the error.                     NSLog(@"Error opening up the database");                 }                 else{                     NSLog(@"Created the file--it did not exist");                     [self refreshData];                 }             }];         }     }); }   If you're curious what refreshData looks like, it sends out a NSNotification that the database has been loaded: -(void)refreshData {     NSNotification* refreshNotification = [NSNotificationnotificationWithName:kNotificationCenterRefreshAllDatabaseData object:self.timeTagDB.managedObjectContext  userInfo:nil];     [[NSNotificationCenter defaultCenter] postNotification:refreshNotification];     }   The kNotificationCenterRefreshAllDatabaseData is just a constant I have defined elsewhere that keeps track of all the NSNotification names I use. I pass the managedObjectContext of the newly created file so that my view controllers can have access to it, and start passing it around to one another. The reason we do this as a Notification is because this is being run in the background, so we can't know exactly when it finishes. Make sure you design your app for this! Have some kind of loading indicator, or make sure your user can't attempt to create a record before the database actually exists, because it will crash the app.

  Read the article

• Five Fake Sounds Engineered to Make Your Feel Better [Science]

  - by Jason Fitzpatrick

  As objects in our environment (like cars, ATMs, and phones) have grown lighter and quieter scientists have been carefully engineering their sounds so that they continue to sound like we expect them to. Read on to see how. At the design blog Humans Invent they share five interesting ways that the world around us is being engineered so it sounds the way we expect it to. They start with the example of the car door. Years ago cars were almost entirely steel, the doors were weighty, and when you slammed them it sounded like one big hunk of steel locking into another big hunk of steel (which, in fact, it was). Newer cars are lighter but people still crave that substantial clunk. Humans Invent highlights the effect of consumer desire: A car door is essentially a hollow shell with parts placed inside it. Without careful design the door frame amplifies the rattling of mechanisms inside. Car companies know that if buyers don’t get a satisfying thud when they close the door, it dents their confidence in the entire vehicle. To produce the ideal clunk, car doors are designed to minimise the amount of high frequencies produced (we associate them with fragility and weakness) and emphasise low, bass-heavy frequencies that suggest solidity. The effect is achieved in a range of different ways – car companies have piled up hundreds of patents on the subject – but usually involves some form of dampener fitted in the door cavity. Locking mechanisms are also tailored to produce the right sort of click and the way seals make contact is precisely controlled. On average it takes 1.8 seconds to close a car door but in that time you’re witnessing a strange kind of symphony composed by engineers and designers whose goal is to reassure you that its rock solid. They mention lock mechanisms, something you may never have thought about. A friend of mine had a Ford Focus some years ago and that particular model had electric locks that, instead of giving a satisfying thunk or solid click, made this horrible gates-of-the-prison-buzzing sound that was completely unnerving. Hit up the link below to see how sounds are engineered for car doors, electric motors, ATM machines, and more. 5 Fake Sounds Designed to Help Humans [Humans Invent via Boing Boing] How To Easily Access Your Home Network From Anywhere With DDNSHow To Recover After Your Email Password Is CompromisedHow to Clean Your Filthy Keyboard in the Dishwasher (Without Ruining it)

  Read the article

• Live CD has black screen HP DV6

  - by Shaun Killingbeck

  Attempting to install/try ubuntu (11.10, 12.04) on my new laptop, using a liveCD (and tried USB). I get the purple screen (with the man/keyboard at the bottom) and after that the screen flashes bright white before going black. Ubuntu continues to load in the background, with login sound etc but the screen is off. I have tried as many different solutions as I could find including: using nomodestep, xforcevesa, i915.modeset=0, and also now i915.modeset=1 in boot options (seperately): varying consequences, but either I end up at a blinking cursor with no prompt, a command line (startx fails: no screen found), or the original blank screen again Tried booting from VirtualBox - it crashes at the same place the screen would go blank when using a CD/USB tried 11.04: I don't have this problem BUT when trying to install, I get a ubi-partman error 141 (possibly down to the three partitions that came on my laptop... not sure why HP needed there own separate partition for HP Tools...) Model: HP Pavillion DV6 6B08SA Processor: AMD Quad-Core A6-3410MX APU with Radeon HD 6545G2 Dual Graphics (1.6 GHZ 4 MB L2 cache ) Chipset: AMD RS880M Any help would be greatly appreciated. I just want to be able to partition the drive and install Ubuntu. I'm assuming the issue is graphics card related, although I have no confirmation of that. Update: Tried the ?orkarounds on https://wiki.ubuntu.com/X/Troubleshooting/BlankScreen - set gfxpayload=text changed nothing, removing splash did nothing and setting vesafb.nonsense=1 did nothing either. I'd like to be able to collect some log information somehow, but I can't get to a command line from the liveCD. tried using the latest 12.04 beta, same issue tried nomodeset without splash or quiet. get the following (tail of) output before it freezes on that screen: * Starting configure network device security [OK] * Starting configure network device [OK] [ 25.720899] ieee80211 phy0: w1_ops_config: change monitor mode: false (implement) [ 25.720923] ieee80211 phy0: w1_ops_config: change power-save mode: false (implement) * Starting restore sound card(s') mixer state(s) [fail] [ 25.721849] ieee80211 phy0: w1_ops_bss_info_changed: qos enabled: false (implement) * Stopping save kernel messages [OK] * Starting bluetooth [OK] * PulseAudio configured for per-user sessions saned disabled; edit /etc/default/saned [ 25.988016] hci_cmd_timer: hci0 command tx timeout [ 26.207225] bad LUN (0:1) [ 26.223735] bad target number (1:0) [ 26.252111] bad target number (2:0) [ 26.272170] bad target number (3:0) [ 26.300154] bad target number (4:0) [ 26.328162] bad target number (5:0) [ 26.344180] bad target number (6:0) [ 26.368142] bad target number (7:0) * Checking battery state... [OK] * Stopping System V runlevel capability [OK] Does this give any indication of the problem? the false (implement) messages also reappear when I press the power button to ask it to shutdown, followed by a [fail] status for killing remaining processes.

  Read the article

• TouchDevelop: The Fast Path to Windows 8 and Phone Apps

  - by Clint Edmonson

  Are you looking for a little extra cash for the upcoming holidays? Then you might be interested in creating some cool apps to sell in the Windows Store. Or maybe you’re simply curious and want to try your hand at developing for Windows 8 and Windows Phone. In either case, the newly released TouchDevelop Web App is for you. TouchDevelop Web App is a development environment to create apps on your tablet or smartphone, without requiring a separate PC. Scripts written by using TouchDevelop can access data, media, and sensors on the phone, tablet, and PC. The script can interact with cloud services, including storage, computing, and social networks. TouchDevelop lets you quickly create fun games and useful tools, turning your scripts into true Windows Phone and Windows 8 apps. A year ago, Microsoft Research released TouchDevelop for Windows Phone, which is being used by enthusiasts, students, and researchers to program their phones in fun, inventive, and interesting ways. These scripts are available at TouchDevelop for anyone to download and use. Ever since we released TouchDevelop, we’ve been eyeing the tablet form factor and working on a version for the browser. Now, with the release of TouchDevelop Web App, the wait is over: the tablet version is ready, so go play around with it. All TouchDevelop scripts that are developed on the smartphone can be downloaded to the tablet and run (if hardware allows). Any script that is developed on the tablet can also be accessed on the phone. And scripts can be converted to Windows Phone or Windows 8 apps and submitted to the Windows Phone Store or Windows Store, respectively. TouchDevelop Web App’s editor and programming language have been designed for tablet devices with touchscreens, but you can also use a keyboard and a mouse. So grab your web-enabled device and give the TouchDevelop Web App a try. It’s fun and easy, and could even put a little cash in your holiday-depleted wallet. Or at least give you bragging rights at family get-togethers. Are you interested in further tips on Windows 8 development?  Sign up for the 30 to launch program which will help you build a Windows Store application in 30 days.  You will receive a tip per day for 30 days, along with potential free design consultations and technical support from a Windows 8 expert. As always, stay tuned to my twitter feed for Windows 8, Windows Azure and other Microsoft announcements, updates, and links: @clinted

  Read the article

• It's Here! Visual Studio 2010 and ASP.NET 4.0 Ship

  Today Microsoft released Visual Studio 2010 and ASP.NET 4.0. I've been using the RC version of Visual Studio 2010 quite a bit for the past couple of months and have really grown to like it. It has a host of features and enhancements that improve developer productivity, from improved IntelliSense to better multiple monitor support. Plus there's something about the user experience that, to me, makes it feel better than Visual Studio 2008. I don't know if it's the new blue color motif or what, but the IDE seems more modern looking and more responsive to my mouse movements and other input. Anyway, if you've not yet downloaded Visual Studio 2010 and ASP.NET 4.0, why not? As with previous versions of Visual Studio there's a free Express Edition and VS2010 and ASP.NET 4.0 runs side-by-side with earlier versions of Visual Studio and ASP.NET. And with Visual Studio 2010's multi-targeting you can even use VS2010 as your development editor for ASP.NET 2.0 and ASP.NET 3.5 web applications. (Although be forewarned if you have multiple developers working on the application that the project files in VS2010 and earlier versions of Visual Studio differ.) This week's article on 4Guys explores my favorite new features of Visual Studio 2010. Here's an excerpt: The Visual Studio 2010 user experience is noticeably different than with previous versions. Some of the changes are cosmetic - gone is the decades-old red and orange color scheme, having been replaced with blues and purples - while others are more substantial. For instance, the Visual Studio 2010 shell was rewritten from the ground up to use Microsoft's Windows Presentation Foundation (WPF). In addition to an updated user experience, Visual Studio introduces an array of new features designed to improve developer productivity. There are new tools for searching for files, types, and class members; it's now easier than ever to use IntelliSense; the Toolbox can be searched using the keyboard; and you can use a single editor - Visual Studio 2010 - to work on. This article explores some of the new features in Visual Studio 2010. It is not meant to be an exhaustive list, but rather highlights those features that I, as an ASP.NET developer, find most useful in my line of work. Read on to learn more! And, in closing, here are some helpful VS2010 and ASP.NET 4.0 links: One click installation for ASP.NET 4.0, Visual Web Developer 2010, .NET Framework 4.0, and ASP.NET MVC 2 Eight Quick Hit videos showing some of the cool new VS2010 features VS2010 and ASP.NET 4.0 Release Announcement with some great info/links from none other than Scott Guthrie Happy Programming!Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• Lock mouse in center of screen, and still use to move camera Unity

  - by Flotolk

  I am making a program from 1st person point of view. I would like the camera to be moved using the mouse, preferably using simple code, like from XNA var center = this.Window.ClientBounds; MouseState newState = Mouse.GetState(); if (Keyboard.GetState().IsKeyUp(Keys.Escape)) { Mouse.SetPosition((int)center.X, (int)center.Y); camera.Rotation -= (newState.X - center.X) * 0.005f; camera.UpDown += (newState.Y - center.Y) * 0.005f; } Is there any code that lets me do this in Unity, since Unity does not support XNA, I need a new library to use, and a new way to collect this input. this is also a little tougher, since I want one object to go up and down based on if you move it the mouse up and down, and another object to be the one turning left and right. I am also very concerned about clamping the mouse to the center of the screen, since you will be selecting items, and it is easiest to have a simple cross-hairs in the center of the screen for this purpose. Here is the code I am using to move right now: using UnityEngine; using System.Collections; [AddComponentMenu("Camera-Control/Mouse Look")] public class MouseLook : MonoBehaviour { public enum RotationAxes { MouseXAndY = 0, MouseX = 1, MouseY = 2 } public RotationAxes axes = RotationAxes.MouseXAndY; public float sensitivityX = 15F; public float sensitivityY = 15F; public float minimumX = -360F; public float maximumX = 360F; public float minimumY = -60F; public float maximumY = 60F; float rotationY = 0F; void Update () { if (axes == RotationAxes.MouseXAndY) { float rotationX = transform.localEulerAngles.y + Input.GetAxis("Mouse X") * sensitivityX; rotationY += Input.GetAxis("Mouse Y") * sensitivityY; rotationY = Mathf.Clamp (rotationY, minimumY, maximumY); transform.localEulerAngles = new Vector3(-rotationY, rotationX, 0); } else if (axes == RotationAxes.MouseX) { transform.Rotate(0, Input.GetAxis("Mouse X") * sensitivityX, 0); } else { rotationY += Input.GetAxis("Mouse Y") * sensitivityY; rotationY = Mathf.Clamp (rotationY, minimumY, maximumY); transform.localEulerAngles = new Vector3(-rotationY, transform.localEulerAngles.y, 0); } while (Input.GetKeyDown(KeyCode.Space) == true) { Screen.lockCursor = true; } } void Start () { // Make the rigid body not change rotation if (GetComponent<Rigidbody>()) GetComponent<Rigidbody>().freezeRotation = true; } } This code does everything except lock the mouse to the center of the screen. Screen.lockCursor = true; does not work though, since then the camera no longer moves, and the cursor does not allow you to click anything else either.

  Read the article

• why are my players drawn to the side of my viewport

  - by Jetbuster

  Following this admittedly brilliant and clean 2d camera class I have a camera on each player, and it works for multiplayer and i've divided the screen into two sections for split screen by giving each camera a viewport. However in the game it looks like this I'm not sure if thats their position relative to the screen or what The relevant gameScreen code, the makePlayers is setup so it could theoretically work for up to 4 players private void makePlayers() { int rowCount = 1; if (NumberOfPlayers > 2) rowCount = 2; players = new Player[NumberOfPlayers]; for (int i = 0; i < players.Length; i++) { int xSize = GameRef.Window.ClientBounds.Width / 2; int ySize = GameRef.Window.ClientBounds.Height / rowCount; int col = i % rowCount; int row = i / rowCount; int xPoint = 0 + xSize * row; int yPoint = 0 + ySize * col; Viewport viewport = new Viewport(xPoint, yPoint, xSize, ySize); Vector2 playerPosition = new Vector2(viewport.TitleSafeArea.X + viewport.TitleSafeArea.Width / 2, viewport.TitleSafeArea.Y + viewport.TitleSafeArea.Height / 2); players[i] = new Player(playerPosition, playerSprites[i], GameRef, viewport); } //players[1].Keyboard = true; } public override void Draw(GameTime gameTime) { base.Draw(gameTime); foreach (Player player in players) { GraphicsDevice.Viewport = player.PlayerCamera.ViewPort; GameRef.spriteBatch.Begin(SpriteSortMode.Immediate, BlendState.AlphaBlend, SamplerState.PointClamp, null, null, null, player.PlayerCamera.Transform); map.Draw(GameRef.spriteBatch); // Draw the Player player.Draw(GameRef.spriteBatch); // Draw UI screen elements GraphicsDevice.Viewport = Viewport; ControlManager.Draw(GameRef.spriteBatch); GameRef.spriteBatch.End(); } } the player's initialize and draw methods are like so internal void Initialize() { this.score = 0; this.angle = (float)(Math.PI * 0 / 180);//Start sprite at it's default rotation int width = utils.scaleInt(picture.Width, imageScale); int height = utils.scaleInt(picture.Height, imageScale); this.hitBox = new HitBox(new Vector2(centerPos.X - width / 2, centerPos.Y - height / 2), width, height, Color.Black, game.Window.ClientBounds); playerCamera.Initialize(); } #region Methods public void Draw(SpriteBatch spriteBatch) { //Console.WriteLine("Hitbox: X({0}),Y({1})", hitBox.Points[0].X, hitBox.Points[0].Y); //Console.WriteLine("Image: X({0}),Y({1})", centerPos.X, centerPos.Y); Vector2 orgin = new Vector2(picture.Width / 2, picture.Height / 2); hitBox.Draw(spriteBatch); utils.DrawCrosshair(spriteBatch, Position, game.Window.ClientBounds, Color.Red); spriteBatch.Draw(picture, Position, null, Color.White, angle, orgin, imageScale, SpriteEffects.None, 0.1f); } as I said I think I'm gonna need to do something with the render position but I'm to entirely sure what or how it would be elegant to say the least

  Read the article

• My co-worker has not been doing such a good job for the past decade. What do I do? [closed]

  - by stijn

  Possible Duplicate: How do I approach a coworker about his or her code quality? I started working with him almost a decade ago and back then I had never really programmed before, being a young hardware engineer. Right now however I have made quite some progress in all areas being part of software design and i am much, much more skilled than my co-worker who is 15 years older and has been programming more than twice as long. He is super nice and definitely smart enough, but lately his lack of skill and performance are starting to drag me down because we're more and more working on the same codebase. And soon we are going to do a quite ambitious start from scratch creating a whole new hard/software system. I feel it is time to address all issues now, but i do not know how to start. Here are some of the things that I would like to see him improve on: no consistent usage of style, spaces nor tabs (eg if(something ) a =b ) adds newlines around pieces of code to make it easier to read, then commits those with messages like 'no changes made' overall commit messages are useless and so are most of the comments, if there are any (eg 'remove solves for bug Rik' if Rik reported a bug). There is no function/class documentation. lots of spelling errors, in both English and native language, which sometimes are mixed 6/7/8 level deep deep nesting is no exception, a lot of functions start with one level already like if(ptr!=Null){ even when ptr is the result of allocation via new in the constructor numerous source files have over 10k lines of those lines, a major part is simply a result of copy-pasting functionality instead of using a function. This includes copying comments so we end up with 50 occurrences of var=NULL; //TODO TEST this!!!!!!! another part is hundreds of lines of dead code knows what versioning does, yet comments out old code and places new code underneath it when making changes coding skills are below par, especially for the type of rather high precision applications we do. Yet somehow, after a lot of trying and testing, stuff starts to work. But then breaks again some time later because every change casues a waterfall effect. violates every single item in the C++ FAQ lite, practices every bad practice I can think of still doesn't know how to properly use the debugger, but spends hours inspecting messy logfiles in notepad on a tiny laptop screen. Does not make any adjustments to the settings of the software he uses. Never uses keyboard shortcuts. does not seem to progress or learn new things at all. Work rather slow, mostly due to the lack of planning and incorrect usage of tools. How does one deal with this? For starters, how do I make him aware of all these problems? Should I tell the staff about it? And the next step, how to get him to learn new things and adopt another way of working?

  Read the article

• Ubuntu is booting on acer e1-510 laptop, but screen displays nothing

  - by user287602

  Tried loading ubuntu 12.04 (32-bit as well 64 bit) through bootable usb , on a brand new 64-bit acer E1-510 laptop. It shows the 'Try ubuntu without installing screen' and I selected that option. But instead of showing ubuntu's logo(which implies it is loading). I get a blank screen. The screen is on, but it shows nothing. I tried the same on an old model laptop acer aspire 5738 and it worked like a charm. However, I realized that Ubuntu is actually booting on E1-510 and only the display is not working. How did I arrive at this conclusion? When I select on 'Try ubuntu without installing screen', after about 8-10 seconds I see that the WiFi indicator light on the laptop panel switches on(just like when we boot up a Windows OS or even Ubuntu ). I got an idea that the system booted Ubuntu. To confirm this, I tried to adjust volume using keyboard shortcuts. Voila, I can hear the sound of adjusting volume! That means it has already booted Ubuntu. I confirmed this with another step. I pressed the power button once and after two seconds I pressed ENTER. It began the process of switching off and within 5 seconds the laptop was powered off. You may ask, Why is this a confirmation that Ubuntu has booted? This is because in Ubuntu when you press on power button, a dialog box opens with shut down, restart, suspend option- and the shut down option is already selected by default; so all I have to do is press ENTER to shut down. This again proved that Ubuntu was indeed up and running. Unlike previous 'AskUbunutu' posts about Acer e1-510, I must mention that my laptop came WITH the Legacy BIOS mode, so its not really a problem to boot ubuntu from a bootable pendrive. Only the screen is not working. In case you need to know, I am running Windows 7-Ultimate 64 bit on acer e1-510.

  Read the article

< Previous Page | 210 211 212 213 214 215 216 217 218 219 220 221  | Next Page >