Search Results

Search found 6557 results on 263 pages for 'media centre'.

Page 214/263 | < Previous Page | 210 211 212 213 214 215 216 217 218 219 220 221  | Next Page >

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• Blu-ray BD-R: Would you physically store it in a CaseLogic Wallet pocket?

  - by Rob

  I keep several backup copies of my material and files. For my DVDs, one set of copies is kept in a CaseLogic wallet folder pack, so that I can easily move this around when visiting friends, family or for business. This is highly convenient. The other sets are kept in their jewel cases in hard plastic see thru storage boxes. Although CaseLogic wallet material is designed to be abrasion free, their caveat is that external dust will be the cause of any blemishes. If hard dust gets in these pockets, which is inevitable, this will occasionally cause light hair like scratches on the disc surface as the discs are removed and returned for access to their contents. This is of no consequence as the laser and error correction can more than cope with this. I'm aware that the blu-ray spec requires anti-scratch in disc surfaces but was wondering that, given the smaller pits, would dust and light scratches from wallet storage cause more problems with blu-rays than they would with DVDs? I'm using Blu-ray BD-R and BD-R DL write once media.

  Read the article

• Abnormally high amount of Transmit discards reported by Solarwinds for multiple switches

  - by Jared

  I have several 3750X Cisco switches that, according to our Solarwinds NPM, are producing billions of transmit discards per day. I'm not sure why it's reporting these discards. Many of the ports on the 3750X's have 2960's connected to them and are hardcoded as trunk ports. Solarwinds NPM version 10.3 Cisco IOS version 12.2(58)SE2 Total output drops: 29139431: GigabitEthernet1/0/43 is up, line protocol is up (connected) Hardware is Gigabit Ethernet, address is XXXX (bia XXXX) Description: XXXX MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100/1000BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:47, output 00:00:50, output hang never Last clearing of "show interface" counters 1w4d Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 29139431 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 35000 bits/sec, 56 packets/sec 51376 packets input, 9967594 bytes, 0 no buffer Received 51376 broadcasts (51376 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 51376 multicast, 0 pause input 0 input packets with dribble condition detected 115672302 packets output, 8673778028 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out sh controllers gigabitEthernet 1/0/43 utilization: Receive Bandwidth Percentage Utilization : 0 Transmit Bandwidth Percentage Utilization : 0

  Read the article

• One server running Django (with Nginx and Apache) and Wordpress Blog

  - by JCWong

  I have nginx listening to port 80 for my primary site foo.com. It proxys to port 8080 which is where the Django app lives server { listen 80; server_name www.foo.com foo.com; access_log /home/jeffrey/www/ddt/logs/nginx_access.log; error_log /home/jeffrey/www/ddt/logs/nginx_error.log; location / { proxy_pass http://127.0.0.1:8080; include /etc/nginx/proxy.conf; } location /media/ { root /home/jeffrey/www/ddt/; } location /static/ { root /home/jeffrey/www/ddt/; } location /public/ { root /home/jeffrey/www/ddt/; } } I'd like to have a wordpress blog run on the same server. Apache is listening to port 8080 with this http.conf file NameVirtualHost *:8080 WSGIScriptAlias / /home/jeffrey/www/ddt/apache/ddt.wsgi WSGIPythonPath /home/jeffrey/www/ddt <Directory /home/jeffrey/www/ddt/apache/> <Files ddt.wsgi> Order deny,allow Allow from all </Files> </Directory> I added my Wordpress site using a virtualhost <VirtualHost *:8080> ServerName www.bar.com ServerAlias bar.com DocumentRoot /home/jeffrey/www/jeffrey_wp </VirtualHost> When I go to bar.com I still see my django app. Is it possible for these two sites to run on the same server?

  Read the article

• Verizon 4G LTE vs. a LAN

  - by n8wrl

  I have been having quite a bit of trouble getting my new Verizon 4G-LTE service running on a Windows 7 desktop. My desktop is on a LAN here at home with two other PC's. We all share printers, files, media, etc. Until yesterday, we also shared a Verizon 3G modem via a NetGear 3G broadband WAP. That isn't compatible with the 4G so now I am just trying to get the 4G modem working directly connected to one of the desktops. After some USB wrangling, it seems to work. Except, every 7-10 minutes the connection would drop. After some time on the phone with a very nice Verizon technician, it seems to be staying up - it's been up for 20 minutes now. He told me that my LAN was causing the 4G to drop. That traffic on my LAN, even though it is not destined for the internet (ICS not working yet) was causing the cell tower to detect an 'IP change' and a 'security violation' in my modem and drop my connection. Is this Verizon's way of forbidding more than one computer to share a modem? I have my computer running now without a LAN connection and the 4G is still up. But this isn't practical. Has anyone heard of this?

  Read the article

• Using UDF on a USB flash drive

  - by CesarB

  After failing to copy a file bigger than 4G to my 8G USB flash drive, I formatted it as ext3. While this is working fine for me so far, it will cause problems if I want to use it to copy files to someone which does not use Linux. I am thinking of formatting it as UDF instead, which I hope would allow it to be read (and possibly even written) on the three most popular operating systems (Windows, MacOS, and Linux), without having to install any extra drivers. However, from what I found on the web already, there seem to be several small gotchas related to which parameters are used to create the filesystem, which can reduce the compability (but most of the pages I found are about optical media, not USB flash drives). I would like to know: Which utility should I use to create the filesystem? (So far I have found mkudffs and genisoimage, and mkudffs seems the best option.) Which parameters should I use with the chosen utility for maximum compability? How compatible with the most common versions of these three operating systems UDF actually is? Is using UDF actually the best idea? Is there another filesystem which would have better compatibility, with no problematic restrictions like the FAT32 4G file size limit, and without having to install special drivers in every single computer which touches it?

  Read the article

• How do I make ESXi 5.0 to shutdown virtual machines when the physical power button is pushed?

  - by Pawel Sawicki

  I have a home NAS/DLNA server built out of an HP Micro Server with the HP branded VMware ESXi 5.0.0 build-623860 (free license) installed. Being a home media center I'd like it to be "manageable" by all my household members. This requires that it needs to be powered on an off (including all the VMs inside) by anybody with the physical access to the server by simply pressing the power button on the chassis. The "startup" part is easy to obtain - all I had to do was to configure the startup/shutdown policy: Once the server powers up, all VMs start as well and that's exactly what I need. Well.. it did work up until 5.0.0U1, but that's a different story: http://blogs.vmware.com/vsphere/2012/03/free-esxi-hypervisor-auto-start-breaks-with-50-update-1.html Unfortunately, pressing the power button doesn't gracefully shutdown the guest machines - they are terminated instead. If I run the "shut down" command from the vSphere Client interface guests are powered off. I'd like to get the same end result when the physical power button is switched. I've poked around a bit on the ESXi server. There's a "/sbin/shutdown.sh" script that seemed to do exactly what I need... but after trying it does exactly what the power off button. The "/etc/inittab" contains an entry for the "shutdown" level but I suppose it's not hooked to the power button. I can't find any acpi related configuration, neither do I know what exactly is executed when the power button is pressed. Does anybody have a clue how can I make the VMs shutdown automatically when the physical power switch is pressed to turn of the computer?

  Read the article

• How can I fix video tearing and pausing on Windows XP Flash videos?

  - by xvs

  I have what should be a reasonably fast PC: it's a Quadcore Intel 6600 at 2.4 GHz, 4MB of RAM, an ATI 3800 series video card and an LG L246WP monitor, which I selected particularly because it was supposed to work well with video and have no trails or other artifacts. So I should be able to play video with no problems. And I can, as long as that video isn't Flash video. With Flash, what I see is tearing, especially during pans, and pausing -- every few seconds the video pauses for about 300ms while the sound stays continuous. I tried going into the video card setup and changing vertical sync, pulldown detection, windows media video acceleration, deinterlacing and triple buffering. but no combination of settings I've tried has changed or corrected the problem in any way. I've also tried enabling and disabling hardware acceleration in the Flash settings, to no avail. This problem happens whether or not the video is streaming or has fully streamed in before playing. So, what can I do? Is this just a flash issue or is there a way to get it to work?

  Read the article

• Cisco ASA with CSC module bypassing

  - by Shial

  We recently upgraded from a Watchguard X5500e Peak firewall appliance to a Cisco 5500 ASA with the CSC module. The ASA is running the 8.2 software and the CSC is on the 6.3.1172 software. We've finally gotten everything stabilized after a few weeks of pulling hairs and gnashing of teeth and now its down to trying to setup a few items that were lower on the priority list. With the watchguard we were able to go with the browser to an internal webpage and authenticate against the firewall to allow us to bypass the filters. Useful when a classroom here needs access to streaming media or an executive needs us to download a video. I'm trying to setup something similar but I'm fairly inexperienced with the Cisco devices like this ASA so I'm not sure if its treated as a VPN connection or some kind of ACL. Ideally we would want to setup more than one to limit exposure rather than one thats wide open when used. I did a search and couldn't find anything related to thing in the other questions asked here and I have had no luck googgling it either.

  Read the article

• permanent NAS-mount in Ubuntu - wrong fs type, bad option, bad superblock

  - by Emil

  My network drive shows up in the file browser, just like my external usb-harddrive. Moving, running and editing files works. Hovering over it shows smb://lacie-2big/nasdisk . BUT, when I want to save a file, the drive doesn't come up as an option. All I can see is my other places, including my usb-harddrive. I am a complete newbie but I am GUESSING that it has something to do with the mount not being a "real" mount but just a shortcut to the smb location. So I ran the tutorial at https://wiki.ubuntu.com/MountWindowsSharesPermanently about how to "mount a network drive permanently". edited my fstab to //LaCie-2big/nasdisk /media/nasmount cifs guest,uid=1000,iocharset=utf8,codepage=unicode,unicode 0 0 and running sudo mount -a gave me the following error: mount: wrong fs type, bad option, bad superblock on //LaCie-2big/nasdisk, missing codepage or helper program, or other error (for several filesystems (e.g. nfs, cifs) you might need a /sbin/mount. helper program) In some cases useful info is found in syslog - try dmesg | tail or so Now thats a very helpful error message, BUT, before I go any further, I'd be really thankful if one of you could tell me if I'm even in the right ballpark, or if my actual need: to be able to download files (ie torrents) directly to the drive, can be possible as it is already. Question: How to fix "wrong fs type, bad option, bad superblock on //LaCie-2big/nasdisk, missing codepage or helper program" when running mount -a

  Read the article

• Nginx with http/https - Http seemed redirected to https all the time

  - by dwarfy

  I've this really weird behaviour with my ubuntu 10.04 / nginx 1.2.3 server. Basically I changed the SSL certificates this morning. And ever since it has been behaving weirdly on all apps. Godaddy is reporting that HTTPS/SSL setup is correct. When I try a page it still works correctly when I'm using HTTPS. But when I try using HTTP nginx reports error : 400 Bad Request The plain HTTP request was sent to HTTPS port After looking around on google for hours, I've tried different setup (while originaly my setup was working correctly for longtime, I just renewed certificates) I kindof found a half solution by adding this to my config : error_page 497 $request_uri; The realllly weird thing is that when I use this setup : server { listen 80; server_name john.johnrocks.eu; access_log /home/john/envs/john_prod/nginx_access.log; error_log /home/john/envs/john_prod/nginx_error.log; location / { uwsgi_pass unix:///home/john/envs/john_prod/john.sock; include uwsgi_params; } location /media { alias /home/john/envs/john_prod/johntab/www; } location /adminmedia { alias /home/john/envs/john_prod/johntab/www/adminmedia; } } I still have the same error when using HTTP (while nothing is setup for HTTPS here)?? I'm getting crazy on this !

  Read the article

• Is it possible/practical to install and run Linux on a USB flash drive?

  - by Graeme Donaldson

  I'm going to replace my old 2004 vintage desktop PC soon and I have an idea of what I want to do, I'm just not sure if it's possible or realistic. In the time since I built the old PC it has slowly become less used as a PC and more as a file server, so I figured I'd build a small file server which could also function as a router/DHCP/DNS/whatever box. The idea is to base it on an Atom system. I have my eye on the Intel D510MO for the moment. This supports 2 SATA disks, and I'd prefer to dedicate those to data storage. I'd like to install Ubuntu Server or maybe Debian on a 8/16GB USB flash drive. I have seen plenty of tutorials on how to perform an installation from a USB drive, but I can't seem to find any info on actually booting and running the OS from USB flash. Is this even possible? Is it practical? This box will mostly be used for: Making backups of mine and my wife's notebooks via LAN. Will use SMB or NFS for this. Digital media storage, which will be accessed by a Mede8er box with no storage of its own. I will most likely use NFS for this.

  Read the article

• can't backup to a NAS drive as offline schedule task

  - by imageng

  I have seen this problem issue discussed in several forums including this one, but could not find a solution. On MS server 2003 I configured a Backup task, the target backup is on a NAS disc (Seagate BlackArmor NAS 110). The backup task is working well as a scheduled task or by a direct command, when I am logged on. It is not working when the user is offline (in this case - Administrator). I already tried the following actions: 1) addressing to the target as network drive (Y:location..), 2)Using UNC instead, 3) making the drive a domain member (the NAS admin S/W allows to define itself as a domain member) The result log message for 1 and 2 is: "The operation was not performed because the specified media cannot be found." The result log message for 3 is empty file. The schedule task "RUN" command is: C:\WINDOWS\system32\ntbackup.exe backup "@C:\Documents and Settings\Administrator\Local Settings\Application Data\Microsoft\Windows NT\NTBackup\data\de-board.bks" /a /d "Set created 2/14/2010 at 5:10 PM" /v:yes /r:no /rs:no /hc:off /m incremental /j "de-board" /l:s /f "\10.0.0.8\public\Backups\IBMServer\de-board.bkf" 10.0.0.8 is the static IP of the NAS. "Run only if logged on" is NOT marked. Password of the administrator user is set. It is obvious that there is no access to the NAS when the user is logged-out. Do you have any idea how can I solve it? Thanks

  Read the article

• What is the point of PPPoE?

  - by aaa90210

  I am trying to expand my knowledge of networking beyond the basics. I have started reading about PPP, and how it is used in DSL modems with PPPoE and PPPoA. My first impression of PPP was "well that seems pretty similar to Ethernet". They are both data link layer protocols. They both have fields to identify the encapsulated protocol (e.g. IP). They both have related protocols to assign IP addresses (DHCP and NCP). So my first question was "so what's the point of PPP, why not just use Ethernet?". The answer to that was fairly straightforward - Ethernet is not supported over a wide range of media like serial lines, and is a fairly specific technology to LAN's using CAT5 or similar. HOWEVER - then I was reading about PPPoE, and the obvious thought was "well if we are doing something over Ethernet, then Ethernet must be available and in use, so why not just use it?". In other words, PPPoE seems to be encapsulating one data-link layer protocol in another very similar protocol. Why do IP-inside-PPP-inside-Ethernet when we could just be doing IP-inside-Ethernet, and use DHCP rather than NCP to assign the IP address to the home router? Thanks

  Read the article

• Automated Scanning for Corrupted Archive Files

  - by Synetech inc.

  Hi, I have all kinds of files that I have downloaded from everywhere over the years scattered around my hard drives. I’m in the process of trying to organize them all and have run into a problem. Sometimes a file was not downloaded correctly (this was a big issue when Chromium first came out) and is thus corrupt. For media files, this is relatively simple to determine (it requires actually opening and examining the file). For executables or other binaries, it is relatively difficult (executables may or may not crash, other binaries could be completely unknown). Archive files (eg zip, rar, 7z, exe, ace, etc.) however should be pretty simple, they have a built-in corruption detection facility. My problem now is that I really don’t want to open and test each and every single archived file throughout my drive; that would be a nightmare. I’m looking for a utility that can automate the process. Is there a program that can scan archive files on a drive and list the ones that are corrupt? Thanks a lot.

  Read the article

• Distributed File Systems.

  - by GruffTech

  So, I've been reading several articles around ServerFault as well as google. (For Example, this link) My Requirements are very similar to the link above, however i'd like to also have dynamic or at least resizeable file volumes, so if necessary i can add 4-5 servers to the pool, and then expand the volume. Any Distributed File systems that support that, to save me some time? Thanks! LustreFS will be my next test cluster to build. GlusterFS I've build a 3-machine test GlusterFS cluster, However i quickly became aware of several of its limitations that it doesn't seem to make clearly public. One, i can't seem to resize a volume. Once a volume is created, its done. Which seems retarded, why have a fully scalable file system if i can't scale a volume? So maybe i'm doing something wrong. I'm not sure. AmazonS3 while gives the cheapest startup adds too much cost when broken down to per client per month, so its out. Building my own system when prorated over several years with no bandwidth costs makes it significantly cheaper. MogileFS isn't an option as we'd like this server to be a SAN-Replacement, for storing tons of media from a multitude of systems, which for us means it needs to be POSIX compliant so it can be remotely mounted via NFS or CIFS.

  Read the article

• CentOS 6.0 yum audacity dependency

  - by Kaemic

  I'm trying to install audacity on centos using yum and I cant force yum to resolve all dependencies, here's what i got, can someone help me with it (when I download the rpm file and click-installit i get the dependency problem too): # yum --disablerepo=c6-media install audacity-1.2.3-2.2.el4.rf.i386.rpm Loaded plugins: fastestmirror, refresh-packagekit Loading mirror speeds from cached hostfile * base: mirror.karneval.cz * centosplus: mirror.karneval.cz * extras: centos.vieth-server.de * rpmforge: fr2.rpmfind.net * updates: mirror.karneval.cz Setting up Install Process Examining audacity-1.2.3-2.2.el4.rf.i386.rpm: audacity-1.2.3-2.2.el4.rf.i386 Marking audacity-1.2.3-2.2.el4.rf.i386.rpm to be installed Resolving Dependencies --> Running transaction check ---> Package audacity.i386 0:1.2.3-2.2.el4.rf set to be updated --> Processing Dependency: wxGTK >= 2.4.0 for package: audacity-1.2.3-2.2.el4.rf.i386 --> Processing Dependency: libwx_gtk-2.4.so.0 for package: audacity-1.2.3-2.2.el4.rf.i386 --> Processing Dependency: libwx_gtk-2.4.so.0(WXGTK_2.4) for package: audacity-1.2.3-2.2.el4.rf.i386 --> Running transaction check ---> Package audacity.i386 0:1.2.3-2.2.el4.rf set to be updated --> Processing Dependency: libwx_gtk-2.4.so.0 for package: audacity-1.2.3-2.2.el4.rf.i386 --> Processing Dependency: libwx_gtk-2.4.so.0(WXGTK_2.4) for package: audacity-1.2.3-2.2.el4.rf.i386 ---> Package wxGTK.i686 0:2.8.12-1.el6.rf set to be updated --> Finished Dependency Resolution Error: Package: audacity-1.2.3-2.2.el4.rf.i386 (/audacity-1.2.3-2.2.el4.rf.i386) Requires: libwx_gtk-2.4.so.0 Error: Package: audacity-1.2.3-2.2.el4.rf.i386 (/audacity-1.2.3-2.2.el4.rf.i386) Requires: libwx_gtk-2.4.so.0(WXGTK_2.4) You could try using --skip-broken to work around the problem You could try running: rpm -Va --nofiles --nodigest

  Read the article

• Windows PE network setup

  - by microchasm

  I'm walking through the following step-by-step guide for deploying Windows 7 via AIK: http://technet.microsoft.com/en-us/library/dd349348%28WS.10%29.aspx On step 4 (Capturing the Installation onto a Network Share), I run into a bit of a snag: attempting to connect to a network drive repeatedly fails. I'm using/deploying Dell Optiplex 380 64 bit machines, and the network cards seem to be really wonky. On the machine that I'm using to run AIK etc, the network driver wasn't found automatically. I had to manually go in and install the driver (which was found on the OEM installation media). I've since copied this to the USB key that I'm using for the Autounattend.xml so its handy. I think that because of this, the PE environment doesn't or can't instantiate the network device. Is there a way to install/configure the network device through the command prompt in PE? If not, I read about adding in the answer file path(s) to drivers, but if I did it this way, would I have to start the process all over again (i.e. create new Autounattend.xml with the PnPcustomizations path included, re-run the installation on the reference machine, install all the applications, re-make the PE iso, reboot into new PE iso)? Any shortcuts, direction, or advice would be appreciated. Thanks!

  Read the article

• Alternative software for Pinnacle PCTV 100e

  - by Stijn Sanders

  I have a Pinnacle PCTV 100e external USB cable television receiver. I've been using Pinnacle's software that came with the card (TVCenter Pro) to record things at given times. Things I don't like is an extremely high CPU load, and that it doesn't seem to halt the screensaver from running when watching in full screen. Also, I was away the last two weeks, and the schedules went terribly bust. Some items were recorded hours before or after the actual scheduled time (and now I missed some shows), and some recurring schedules weren't converted into the next occurrence correctly! Is there good alternative software that would work with my PCTV 100e? (Preferalby cheap or free) I've tried VLC Player, which gets video, but no audio. I've tried MediaPortal, which crashes when trying to scan for channels. When I select a channel manually, the stored mpg has big errors in encoding and is also missing audio. There's VirtualDub, but that doesn't have ready-made scheduled-recording options. This I can conjure some scheduled scripts for, but I've noticed the sync gets awfully wrong after some time. I've tried Windows Media Center, but it doesn't seem to support the PCTV 100e.

  Read the article

• SATA Blu-Ray drive not detected via USB adapter

  - by LTR

  I'm using an SATA blu-ray drive (Lite-On IHOS104), connected via a USB adapter to my Windows 7 (32-bit) notebook. The first time I plugged the adapter in, it worked perfectly. The drive appeared in Explorer, and my player software was able to play an encrypted Blu-Ray disc just fine. After the first reboot, it never worked again. Now it shows up as "removable media" with a size of 0 bytes, irregardless of whether a disk is inserted or not. The drive does not show up under the green "eject USB device" icon in the taskbar. The adapter is powered using a separate power adapter. I have tried: disconnecting all other USB devices testing with a DVD instead of a Blu-Ray disc letting Windows search for updated drivers for the drive - there are none using the same drive and adapter on another Win7 (but x64) computer. They work perfectly. using other USB ports on the same notebook - tried them all. using a different SATA/USB-adapter What else can I do to diagnose this problem?

  Read the article

• Using UDF on a USB flash drive

  - by CesarB

  After failing to copy a file bigger than 4G to my 8G USB flash drive, I formatted it as ext3. While this is working fine for me so far, it will cause problems if I want to use it to copy files to someone which does not use Linux. I am thinking of formatting it as UDF instead, which I hope would allow it to be read (and possibly even written) on the three most popular operating systems (Windows, MacOS, and Linux), without having to install any extra drivers. However, from what I found on the web already, there seem to be several small gotchas related to which parameters are used to create the filesystem, which can reduce the compability (but most of the pages I found are about optical media, not USB flash drives). I would like to know: Which utility should I use to create the filesystem? (So far I have found mkudffs and genisoimage, and mkudffs seems the best option.) Which parameters should I use with the chosen utility for maximum compability? How compatible with the most common versions of these three operating systems UDF actually is? Is using UDF actually the best idea? Is there another filesystem which would have better compatibility, with no problematic restrictions like the FAT32 4G file size limit, and without having to install special drivers in every single computer which touches it?

  Read the article

• Why can't I boot in to Windows Recovery Environment to fix my HDD or salvage my data?

  - by Kevin

  I've been trying to get in to WindowsRE to salvage the files on my Sony Vaio laptop after it failed to load Vista (it finally, consistently displays "Error loading operating system" after months of such intermittent failures, usually rectified via restarts or utilizing Startup Repair or CHKDSK from WindowsRE) . The problem is, after successfully accessing it once after this failure (and many times before over the course of the laptop's life), I can no longer get it to load. During the last successful access (right after the failure), I ran startup repair, which itself failed and notified me that the boot sector was corrupt. I attempted to head in to Sony's proprietary recovery tools menu, which is accessible from WindowsRE when it is loaded from the recovery partition or recovery disk, however it hung. I have since been unable to access the recovery environment after restarting, using any of these methods: Access via the recovery partition (pressing F10 on boot) Access via recovery DVD (created using the same computer when it was healthy) Access via a Windows Vista installation DVD All three methods produce the same results: The computer acknowledges the boot attempt The computer successfully gets passed the "Windows is loading files" screen The computer successfully gets passed the Windows loading screen The computer then stalls at a black screen, while showing HDD activity (via indicator light). After a few minutes, the HDD activity ceases, and after a few more minutes, the over sized cursor that is utilized in WindowsRE appears on the black screen. The actual recovery environment, however, never appears, even after leaving the computer in such a state overnight. What is fustrating is that other bootable utilities, such as SeaTools for DOS and MemTest, boot up and run fine. In running perfectly normally, MemTest was able to produce a plethora of errors utilizing my RAM. I'm inclined to believe the RAM's faultiness may causing the WindowsRE booting to fail. Would this be a valid assumption? If I'm not mistaken, booting from external media utilizes the RAM, so such a reason is plausible, assuming my knowledge of bootloading is correct. Other than that, I can't figure out any reason why all the bootable utilities except WindowsRE run fine. Does anyone know what the problem is, or could be? Any solutions?

  Read the article

• Offline copies in Windows file sharing

  - by netvope

  I frequently access media files (music or video) on a remote Windows file share. My Internet connection is not very fast, and I find it a waste of bandwidth when I repeatedly access the same files. For example, I may listen to the same song 30 times in a month. So, I would like to cache files I've used. I know Windows has an "Always available offline" feature but I think it doesn't suit my needs. I don't want to make the whole share "available offline" as the remote Windows file share is huge (in terabytes). Making individual files "available offline" is tedious as the files are scattered in many different directories. It would be much more convenient if I can simply cache those I've used. Also The files on the share seldom change. Many of the files are rarely used. Some of the files are frequently used. I don't have a list of the most frequently used files. So I think the best way is to have a caching proxy for the Windows share. What do you think? I have a Linux box sitting around. Perhaps I should try to setup samba4?

  Read the article

• Is StoreJet Transcend (0x2329) an Advanced Format drive?

  - by Graham Perrin

  I use a 640 GB StoreJet Transcend (0x2329) with ZEVO Community Edition 1.1.1 on OS X 10.8.2. Question Is this drive Advanced Format? Background I submitted a request for technical support to Transcend but the first response was gibberish so I don't expect a reasonable follow-up. Models at http://www.transcend-info.com/Products/CatList.asp?LangNo=0&ModNo=293 are similar but different sizes (not 640 GB). Mine is probably 25M2 (TS640GSJ25M2): Unless I'm missing something, nothing currently in the Transcend support area tells me whether the drive is Advanced Format. From System Information in OS X 10.8.2: StoreJet Transcend: Capacity: 640.14 GB (640,135,028,736 bytes) Removable Media: Yes Detachable Drive: Yes BSD Name: disk3 Product ID: 0x2329 Vendor ID: 0x152d (JMicron Technology Corp.) Version: 0.00 Serial Number: 322549FBA004 Speed: Up to 480 Mb/sec Manufacturer: JMicron History for the ZFS pool shows creation in March 2012 –  macbookpro08-centrim:~ gjp22$ zpool history zhandy | grep create 2012-03-14.17:29:37 zpool create -f -O compression=off -O copies=1 -O casesensitivity=insensitive -O snapdir=visible zhandy /dev/dsk/GPTE_1928482A-7FE4-482D-B692-3EC6B03159BA 2012-06-22.15:51:16 zfs create zhandy/Pocket Time Machine At that time I almost certainly used ZEVO Setup Assistant to create the pool. macbookpro08-centrim:~ gjp22$ zpool get ashift zhandy NAME PROPERTY VALUE SOURCE zhandy ashift 0 default If I discover that the drive is Advanced Format, a different ashift value will be appropriate.

  Read the article

< Previous Page | 210 211 212 213 214 215 216 217 218 219 220 221  | Next Page >