Search Results

Search found 89025 results on 3561 pages for 'spring dm server'.

Page 214/3561 | < Previous Page | 210 211 212 213 214 215 216 217 218 219 220 221  | Next Page >

• Recommended Win2k8 Server software to fix my RAID-0 issue

  - by Jason Kealey

  I'm running an Asus P6T V2 Deluxe. It has six SATA ports and supports onboard RAID. I am using two of those ports for a RAID0 array of 1.5TB Seagate drives using the onboard RAID controller. One of them is giving me SMART warnings and I want to preemptively replace it. I pulled out two other 1.5TB drives from another computer and am ready to use one or both, if necessary. I can't run any SMART diagnostic software from within Windows because it only sees the hardware RAID-0 array, not each individual drive. The first thing I tried was a slow sector-by-sector copy using a free tool called EASEUS Disk Copy. Used the bootdisk, copied (took like 16 hours), unplugged the defective drive and plugged the new one in its place. The motherboard didn't recognize the new drive as being part of the known setup, so it did not want to boot. The second thing I tried was using other software (I forget the name) to copy the partition from within Windows. The first software failed because I had a server operating system. I found another software (I forget the name) which supported a server OS and did a partition copy onto the new drive. This seemed to work and the OS started to boot, but blue screened and started a reboot cycle. I'm assuming the software I was using was no good as it was trying to copy the boot disk while it was in use. I am looking for recommendations on what software to use to fix my problem without doing a re-install. Everything is backed up but my computer works fine and I'd like to avoid re-installation when possible. However, my system would be back up now if I had just started over on a second RAID array. :)

  Read the article

• Windows Server 2003 IPSec Tunnel Connected, But Not Working (Possibly NAT/RRAS Related)

  - by Kevinoid

  Configuration I have setup a "raw" IPSec tunnel between a Windows Server 2003 (SBS) machine and a Netgear FVG318 according to the instructions in Microsoft KB816514. The configuration is as follows (using the same conventions as the article): NetA | SBS2003 | FVG318 | NetB 10.0.0.0/24 | 216.x.x.x | 69.y.y.y | 10.0.254.0/24 Both the Main Mode and Quick Mode Security Associations are successfully completed and appear in the IP Security Monitor. I am also able to ping the SBS2003 server on its private address from any computer on NetB. The Problem Any traffic sent from a computer on NetA to NetB, or from SBS2003 to NetB (excluding ICMP Ping responses), is sent out on the public network interface outside the IPSec tunnel (no encryption or header authentication, as if the tunnel were not there). Pings sent from a computer on NetB to a computer on NetA successfully reach computers on NetA, but the responses are silently discarded by SBS2003 (they do not go out in the clear and do not generate any encrypted traffic). Possible Solutions Incorrect Configuration I could have mistyped something, somewhere, or KB816514 could be incorrect in some way. I have tried very hard to eliminate the first option. Have re-created the configuration several times, tried tweaking and adjusting all the settings I could without success (most prevent the SA from being established). NAT/RRAS I have seen multiple posts elsewhere suggesting that this could be due to interaction between NAT and the IPSec filters. Possibly the NetA private addresses get rewritten to 216.x.x.x before being compared with the Quick Mode IPSec filters and don't get tunneled because of the mismatch. In fact, The Cable Guy article from June 2005 "TCP/IP Packet Processing Paths" suggests that this is the case, (see step 2 and 4 of the Transit Traffic path). If this is the case, is there a way to exclude NetA-NetB traffic from NAT? Any thoughts, ideas, suggestions, and/or comments are appreciated.

  Read the article

• Force delivery retry without restarting the SMTP Service on Windows Server 2008 R2

  - by Mathias R. Jessen

  I have a Windows Server 2008 R2 box hosting 3 virtual SMTP servers; vSMTP01, vSMTP02 and vSMTP03. The first two are configured to deliver all messages to dedicated smarthosts, while the last is set to just deliver the messages on its own. All other delivery settings are as default ----(vSMTP01)-----> {SMARTHST01} / ----Inbound mail--->---SMTPSRV01---[----(vSMTP02)-----> {SMARTHST02} \ ----(vSMTP03)-----> { Internet } Now I want to take SMARTHST01 out for maintenance, but I don't want to reject submissions to vSMTP01 while doing so, so I just let it continue running. When SMARTHST01 is no longer responding, vSMTP01 queues the messages and wait for the first retry interval to pass (15 minutes). So far so good. Let's say SMARTHST01 gets online again after 20 minutes. The first interval has passed, and I'll have to wait another 25 minutes for the second retry interval to pass. If I stop and start the SMTP Service (Services.msc - Simple Mail Transfer Protocol service - Stop), the server will retry all deliveries, but that would cause a service interruption for ALL virtual SMTP servers on the machine, which is highly undesirable. How can I manually force vSMTP01 to retry delivery of all queued messages without interrupting the service of vSMTP02 and vSMTP03?

  Read the article

• Update Grub on Squeeze - Kernel downgrade due VMware Server

  - by vodoo_boot

  I happen to run into various problems regarding grub and kernels. I don't really care about the kernel internas. All I want is VMware server in that dedicated root-server. 1.) What is a bzImage vs. vmlinuz? kaze:~# ls /boot/ System.map-2.6.32-5-amd64 bzImage-2.6.33.2 config-2.6.33.2 initrd.img-2.6.32-5-amd64 System.map-2.6.33.2 bzImage-2.6.35.6 config-2.6.35.6 vmlinuz-2.6.32-5-amd64 System.map-2.6.35.6 config-2.6.32-5-amd64 grub I updated my menu.lst (grub2): timeout 5 default 0 fallback 1 title 2.6.32.5 kernel (hd0,1)/boot/vmlinuz-2.6.32-5-amd64 root=/dev/sda2 panic=60 noapic acpi=off title 2.6.35.6 kernel (hd0,1)/boot//bzImage-2.6.35.6 root=/dev/sda2 panic=60 noapic acpi=off title 2.6.32.3 kernel (hd0,1)/boot//bzImage-2.6.33.2 root=/dev/sda2 panic=60 noapic acpi=off That doesn't do well... I think the vmlinuz file is missing initrd or so. Dunno. In fact I don't give too much about kernel boot voodoo as long as it works. update-grub(2) does not work. Does anybody know what magical trick there is to get the 2.6.32-5 booting? 2.) I thought t follow the Deban wiki.. I cannot get header-files for the installed 35.6 or 33.2 kernel in the repositories. I cannot build foreign headers because they will not match the running kernel. So how does one deal with that situtation? I'd prefer not to have to downgrade the kernel. Thanks for any answers!

  Read the article

• Server 2008 email on Event variables

  - by Jeff Miles

  One of the new features of Server 2008 is the ability to attach a task to a specific event in the event logs. One of the actions available is to send an email through a SMTP server. This is working great, however it would be ideal if in the message body, the Event contents could be placed. I have tried using $eventdescription and %eventdescription%, but those are just shots in the dark. Any amount of googling produces no results. Does anyone know if this is possible? Update: Sparks' suggestion below is a step in the right direction I believe, however that method doesn't seem to work for all values. For example, I can pull the RecordID, Severity and Channel as shown, but I can't use the same method to retreive the EventID, or most importantly the description. Here's the raw XML from one event: [Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"] [System] [Provider Name="DFSR" /] [EventID Qualifiers="16384"]4412[/EventID] [Level]4[/Level] [Task]0[/Task] [Keywords]0x80000000000000[/Keywords] [TimeCreated SystemTime="2009-05-14T18:18:09.000Z" /] [EventRecordID]45692[/EventRecordID] [Channel]DFS Replication[/Channel] [Computer]servername.domain.com[/Computer] [Security /] [/System] [EventData] [Data]9046C3F4-843E-4A53-B941-4B20764072E5[/Data] [Data]D:\departments\Geomatics\Plan Quality\Data Processing\CG3533017 2009-05-13 KT FIXED[/Data] [Data]D:\departments[/Data] [Data]{26D5F604-E603-4F87-8EC3-DE9A945DA8FD}-v927199[/Data] [Data]Departments[/Data] [Data]domain.ca\files\departments[/Data] [Data]B8242CE2-F5EB-47DA-BA5B-1DD2F7EE3AB9[/Data] [Data]DFAA7A54-66CB-4C31-81A0-0F861382C32C[/Data] [Data]CG3533017 2009-05-13-{26D5F604-E603-4F87-8EC3-DE9A945DA8FD}-v927199[/Data] [/EventData] [/Event] I have tried using a ValueQuery for EventData, but it returns no data.

  Read the article

• Windows module installer delaying login, server 2008 R2

  - by Kyle

  We updated our servers this weekend (windows updates), everything went fine except one of our terminal servers now hangs at login with the message, "waiting for windows modules installer." It eventually times out and leaves an event log message that the service has stopped unexpectedly. I have disabled the service and users can now login in a reasonable time frame. However we will need to re-enable the service in order to install further updates. I'm not sure where to start with this one, I'm an entry level admin and my colleagues are on vacation today, thank God this isn't a serious problem. Further details: -It affects all users. -The only third party software on the server is our ERP software and screwdrivers from Tricerat. -The only event log message is that the service has stopped unexpectedly. -The server manager screen does not display any information about roles it just says, "error". -The remote desktop roles all seem to be functioning properly, Remote app works as well as standard RDP. Let me know if there is any further details I can provide, I will be checking this frequently throughout the day.

  Read the article

• Server 2008 email on Event variables

  - by Jeff Miles

  One of the new features of Server 2008 is the ability to attach a task to a specific event in the event logs. One of the actions available is to send an email through a SMTP server. This is working great, however it would be ideal if in the message body, the Event contents could be placed. I have tried using $eventdescription and %eventdescription%, but those are just shots in the dark. Any amount of googling produces no results. Does anyone know if this is possible? Update: Sparks' suggestion below is a step in the right direction I believe, however that method doesn't seem to work for all values. For example, I can pull the RecordID, Severity and Channel as shown, but I can't use the same method to retreive the EventID, or most importantly the description. Here's the raw XML from one event: [Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"] [System] [Provider Name="DFSR" /] [EventID Qualifiers="16384"]4412[/EventID] [Level]4[/Level] [Task]0[/Task] [Keywords]0x80000000000000[/Keywords] [TimeCreated SystemTime="2009-05-14T18:18:09.000Z" /] [EventRecordID]45692[/EventRecordID] [Channel]DFS Replication[/Channel] [Computer]servername.domain.com[/Computer] [Security /] [/System] [EventData] [Data]9046C3F4-843E-4A53-B941-4B20764072E5[/Data] [Data]D:\departments\Geomatics\Plan Quality\Data Processing\CG3533017 2009-05-13 KT FIXED[/Data] [Data]D:\departments[/Data] [Data]{26D5F604-E603-4F87-8EC3-DE9A945DA8FD}-v927199[/Data] [Data]Departments[/Data] [Data]swg.ca\files\departments[/Data] [Data]B8242CE2-F5EB-47DA-BA5B-1DD2F7EE3AB9[/Data] [Data]DFAA7A54-66CB-4C31-81A0-0F861382C32C[/Data] [Data]CG3533017 2009-05-13-{26D5F604-E603-4F87-8EC3-DE9A945DA8FD}-v927199[/Data] [/EventData] [/Event] I have tried using a ValueQuery for EventData, but it returns no data.

  Read the article

• SQL Server Replication Backup

  - by user18039

  Hi We have a new system that runs on SQL Server 2008 r2 64-bit. There is a primary on-line transactional processing (OLTP) database that accepts a high volume of updates from several thousand Point of Sale systems at stores around the country. In order to protect this vital function, I have decided to introduce a dedicated reporting database server - from which multiple users will run some pretty complex reports. I realise that there were a number of choices but I decided to use Transaction Replication as the mechanism for copying the data from the OLTP database to the new reporting database - one way replication. The solution has worked well in test. I'm now being asked what changes need to be made to the backup policy to cover the architectural changes. I have read pages such as MSDN:Strategies for Backing Up and Restoring Snapshot and Transactional Replication but I think these are overkill for my solution. In fact, my current thinking is that we simply need to continue making backups of the OLTP data and logs. If the Reporting db or any of the system replication (eg distribution) databases fail then it's no big deal - we can clear all down then re-create the replication. I realise that taking a complete snapshot of the OLTP would be time consuming (approx 5 hours) but I'd be more relaxed about this that trying to restore backups of the various data and log files in the correct sequence. My view is that the complex strategies set out in the MSDN article would only be the way to go for a more complex replication solution than I have, eg if there were multiple subscribers with 2-way replication. Would you agree? I'd be grateful for any advice. Many thanks, Rob.,

  Read the article

• Experience with asymmetrical (non-identical hardware) SQL Server 2005 / Win 2003 cluster

  - by user24161

  I am reasonably good at dealing with SQL Server clusters; I am wondering if folks have experience, good or bad, using a mix of different models of servers from the same vendor in one SQL 2005 cluster. Suppose: I have one more powerful, more RAM, more shizzle box and one less powerful, less memory, less shizzle box bound together in a 2-node cluster. These would be HP DL380 and 580 machines (not that it should matter) I understand AND automate the process of managing memory for each SQL instance, so there's no memory contention when SQL instances fail over. Basically I am thinking a CLR proc will monitor the instances and self-regulate memory caps on each instance, so that they won't page or step on one another. I get the fact the instances might be slower and or under memory pressure if they share a "lesser" node, and that's OK. The business can deal with a slower instance in a server-problem scenario. Reasonable? Any "gotchas" to watch out for? More info 10/28: doing some experiments with a test cluster I find that reconfiguring max/min memory is OK PROVIDED the instance isn't already under memory pressure. If I torture the system with a huge query that demands a big chunk of RAM, and simultaneously adjust the memory allocation to a smaller value than what is being actively used, it's possible to run the instance out of memory and have it halt and restart itself (unhappy situation). Many ugly out-of-memory messages in the error log, crashing, burning... It's an extreme case, but good to know. Seems, then, that it would only be really safe to set this on startup of the instance, as in have a startup script that says "I am on node1, so my RAM settings are X or I am on node two, so they are Y," like this: http://sqlblog.com/blogs/aaron_bertrand... Update: I am testing a SQL Agent + PowerShell solution described in more detail here.

  Read the article

• Windows Server 2008 R2 grinds to a screeching halt during file copy operations

  - by skolima

  When my Windows Server 2008 R2 machine is performing any large disk operations (copying 10GB files from one drive to another, copying similar file over network, merging HyperV snapshots, compressing large files), performance of the whole machine slows down terribly, everything becomes unresponsive. This is noticeable in any situation when the disk access is large enough not to fit in the cache. Are there any settings available for tuning this behaviour? I can accept slower file transfer if this would give me more responsiveness. System details: Dell Optiflex 960, Core 2 Quad Q9650, 8GB RAM, 2 SATA drives - 320GB (ST3320418AS) and 1TB (ST31000528AS), NCQ active on both, Intel 82564LM-3 Gigabit Ethernet, ATI HD 3450 graphics, Intel ICH10 bridge. We have multiple machines like this, every one is exhibiting the same behaviour. I though this was overkill for a workstation, apparently I was mistaken. Update: I guess I shouldn't have mentioned the HyperV at all. The above configuration is a standard workstation setup at the company I work for, this is not a server of any kind. I have at most 3 virtual machines working, and usually I'm the only person accessing them. Never the less, the slowdown occurs even when no VMs are running. On a Linux machine I'd simply ionice the copy process and I could forget about it, is there any way to manage IO priorities on Windows?

  Read the article

• PPTP connection fails with errors 800/806

  - by Mark S. Rasmussen

  I've got a client (Server 2008 R2) that won't connect to our production environment PPTP VPN server (Server 2003, running RRAS). The server is behind a firewall that has TCP1723 open as well as GRE. Other clients at our office are able to connect just fine. Our office is behind a Juniper SSG5-Serial firewall, but all outgoing traffic is allowed, and multiple other clients are able to connect to VPN servers without issues. I've also setup a completely different VPN server on another network outside of our office. The functioning clients connect just fine - the Server 2008 R2 machine doesn't. Thus it's definitely a problem with this machine in particular. I've rebooted it. I've disabled the firewall, no dice on either. I've run PPTPSRV and PPTPCLNT on the server/client and they're able to communicate perfectly - indicating there's no problem using neither TCP1723 nor GRE. The Server 2008 R2 machine is also running as a VPN server itself (incoming connection) and that's working perfectly. We have the issues no matter if there are active incoming connections or not. I'm not sure what my next debugging step would be; any suggestions? EDIT: The event log on the server has the following warning from RasMan: A connection between the VPN server and the VPN client xxx.xxx.xxx.xxx has been established, but the VPN connection cannot be completed. The most common cause for this is that a firewall or router between the VPN server and the VPN client is not configured to allow Generic Routing Encapsulation (GRE) packets (protocol 47). Verify that the firewalls and routers between your VPN server and the Internet allow GRE packets. Make sure the firewalls and routers on the user's network are also configured to allow GRE packets. If the problem persists, have the user contact the Internet service provider (ISP) to determine whether the ISP might be blocking GRE packets. Obviously this points to GRE being a potential problem. But seeing as I have other clients connectiong without problems, as well as PPTPSRV and PPTPCLNT being able to communicate, I'm suspecting this might be a red herring. EDIT: Here are the anonymized events logged by the client in chronological order: CoId={742CB15C-A7E0-47B7-8240-0EFA1139CBD9}: The user XXX\YYY has started dialing a VPN connection using a per-user connection profile named ZZZ. The connection settings are: Dial-in User = XXX\YYY VpnStrategy = PPTP DataEncryption = Require PrerequisiteEntry = AutoLogon = No UseRasCredentials = Yes Authentication Type = CHAP/MS-CHAPv2 Ipv4DefaultGateway = No Ipv4AddressAssignment = By Server Ipv4DNSServerAssignment = By Server Ipv6DefaultGateway = Yes Ipv6AddressAssignment = By Server Ipv6DNSServerAssignment = By Server IpDnsFlags = Register primary domain suffix IpNBTEnabled = Yes UseFlags = Private Connection ConnectOnWinlogon = No. CoId={742CB15C-A7E0-47B7-8240-0EFA1139CBD9}: The user XXX\YYY is trying to establish a link to the Remote Access Server for the connection named ZZZ using the following device: Server address/Phone Number = XXX.YYY.ZZZ.KKK Device = WAN Miniport (PPTP) Port = VPN3-4 MediaType = VPN. CoId={742CB15C-A7E0-47B7-8240-0EFA1139CBD9}: The user XXX\YYY has successfully established a link to the Remote Access Server using the following device: Server address/Phone Number = XXX.YYY.ZZZ.KKK Device = WAN Miniport (PPTP) Port = VPN3-4 MediaType = VPN. CoId={742CB15C-A7E0-47B7-8240-0EFA1139CBD9}: The link to the Remote Access Server has been established by user XXX\YYY. CoId={742CB15C-A7E0-47B7-8240-0EFA1139CBD9}: The user XXX\YYY dialed a connection named ZZZ which has failed. The error code returned on failure is 806. Running Wireshark on the client shows it trying and retrying to send a "71 Configuration Request" While the server shows the incoming client requests, but apparently without replying: Given that this is GRE traffic, I think rules out the GRE traffic being blocked. Question is, why doesn't the server reply? This is the Configuration Request the server receives from the non functioning client (meaning no response is sent to the client request): And this is the Configuration Request the server receives from the working client: To me they seem identical, except for differing keys and magic numbers, and the fact that one client receives a response while the other doesn't.

  Read the article

• "shutting down hyper-v virtual machine management service"

  - by icelava

  I have a Windows 2008 R2 server that is a Hyper-V host (Dell PowerEdge T300). Today for the first time I encountered an odd situation; i lost connection with one of the guest machines but logging on physically it seems the guest OS is still running but no longer contactable via the network. I tried to shut down the guest machine (Windows XP) but it would not shut down, getting stuck in a "Not responding" dialog box that cannot be dismissed. I used the Hyper-V management console to reset the machine and it could not get out of resetting state. I tried to save another Windows 2003 guest machine, and it would be progress with its Saving state (0%). The other running Windows 2003 guest was stuck in the logon dialog. My first suspicion is perhaps one of the Windows update patches this week (10 Nov 2011) may something to do with it, which was still pending a system restart. Well, since I could not do anything with Hyper-V i proceeded with the Windows Update restart, and now it is stuck half an hour at "Shutting down hyper-v virtual machine management service" Prior to restarting I did not observe any hard disk errors reported in the system event log; doubt it is a disk-related condition. Shall I force a hard reboot? UPDATE As per answer report, it eventually restarted itself.

  Read the article

• Can't start managed server in Oracle Weblogic 10.3.2

  - by Neuquino

  I installed Oracle SOA Suite 11g. I start the NodeManager successfully. I start the AdminServer successfully. When I go to start the soa serve (soa_server1) I get this output: NMProcess: <Mar 15, 2010 3:33:30 PM> <WARNING> <Exception while starting server 'soa_server1'> NMProcess: java.io.IOException: Server failed to start up. See server output log for more details. NMProcess: at weblogic.nodemanager.server.ServerManager.start(ServerManager.java:331) NMProcess: at weblogic.nodemanager.server.Handler.handleStart(Handler.java:541) NMProcess: at weblogic.nodemanager.server.Handler.handleCommand(Handler.java:116) NMProcess: at weblogic.nodemanager.server.Handler.run(Handler.java:70) NMProcess: at java.lang.Thread.run(Thread.java:619) NMProcess: NMProcess: Mar 15, 2010 3:33:30 PM weblogic.nodemanager.server.Handler handleStart NMProcess: WARNING: Exception while starting server 'soa_server1' NMProcess: java.io.IOException: Server failed to start up. See server output log for more details. NMProcess: at weblogic.nodemanager.server.ServerManager.start(ServerManager.java:331) NMProcess: at weblogic.nodemanager.server.Handler.handleStart(Handler.java:541) NMProcess: at weblogic.nodemanager.server.Handler.handleCommand(Handler.java:116) NMProcess: at weblogic.nodemanager.server.Handler.run(Handler.java:70) NMProcess: at java.lang.Thread.run(Thread.java:619) Error Starting server soa_server1: weblogic.nodemanager.NMException: Exception while starting server 'soa_server1' In the log file I've got this: Enter username to boot WebLogic server:Enter password to boot WebLogic server: There are 1 nested errors: weblogic.management.ManagementException: Booting as admin server, but servername, soa_server1, does not match the admin server name, AdminServer at weblogic.management.provider.internal.RuntimeAccessService.start(RuntimeAccessService.java:67) at weblogic.t3.srvr.ServerServicesManager.startService(ServerServicesManager.java:461) at weblogic.t3.srvr.ServerServicesManager.startInStandbyState(ServerServicesManager.java:166) at weblogic.t3.srvr.T3Srvr.initializeStandby(T3Srvr.java:749) at weblogic.t3.srvr.T3Srvr.startup(T3Srvr.java:488) at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:446) at weblogic.Server.main(Server.java:67) > <Mar 15, 2010 3:33:30 PM ART> <Notice> <WebLogicServer> <BEA-000365> <Server state changed to FAILED> <Mar 15, 2010 3:33:30 PM ART> <Error> <WebLogicServer> <BEA-000383> <A critical service failed. The server will shut itself down> <Mar 15, 2010 3:33:30 PM ART> <Notice> <WebLogicServer> <BEA-000365> <Server state changed to FORCE_SHUTTING_DOWN> <Mar 15, 2010 3:33:30 PM> <FINEST> <NodeManager> <Waiting for the process to die: 31144> <Mar 15, 2010 3:33:30 PM> <INFO> <NodeManager> <Server failed during startup so will not be restarted> <Mar 15, 2010 3:33:30 PM> <FINEST> <NodeManager> <runMonitor returned, setting finished=true and notifying waiters> Do you have any clue of what is happening? If you need more info, just ask for it. thanks in advance

  Read the article

• VSS error 521 when attempting backup

  - by blade

  Hi, I have backupassist and I attempt to run a backup, with VSS service running. However, I get this error in Windows Event Log: The backup operation that started at '?2010?-?04?-?30T01:51:15.601000000Z' has failed because the Volume Shadow Copy Service operation to create a shadow copy of the volumes being backed up failed with following error code '2155348129'. Please review the event details for a solution, and then rerun the backup operation once the issue is resolved. Code: 521. The error in backupassist is: The backup operation stopped before completing. Detailed error: ERROR - A Volume Shadow Copy Service operation error has occurred: (0x80042336) The writer experienced a partial failure. Check the component level error state for more information. Log of files successfully backed up: C:\Windows\Logs\WindowsServerBackup\Backup-29-04-2010_18-51-15.log Log of files for which backup failed: C:\Windows\Logs\WindowsServerBackup\Backup_Error-29-04-2010_18-51-15.log A Volume Shadow Copy Service operation failed. Please check "VSS" and "SPP" application event logs for more information. ERROR - A Volume Shadow Copy Service operation error has occurred: (0x80042336) The writer experienced a partial failure. Check the component level error state for more information. Any idea how to fix this? I work in a company with server engineers, they all state of having no problems with 2008 and VSS (though in the company we use predominantly 2003). Without vss working, I assume no backup application will work? Thanks

  Read the article

• SQL Server Reporting Services Report Viewer wrapper for ASP.NET MVC has been released!

  - by Ilya Verbitskiy

  Originally posted on: http://geekswithblogs.net/ilich/archive/2013/11/04/sql-server-reporting-services-report-viewer-wrapper-for-asp.net-mvc.aspxSQL Server Reporting Services is rich and popular reporting solution that you have free with SQL Server. It is widely used in the industry: from small family businesses running on SQL Server 2008/2012 express to huge corporations with SQL Server clusters. There is one issue with the solution. Microsoft has not release SSRS viewer for ASP.NET MVC yet. That is why people usually mixing modern ASP.NET MVC enterprise applications with ASP.NET Web Forms pages to view report. Today I released ASP.NET MVC HTML helper which renders a basic ASP.NET Web Forms ReportViewer control inside an iframe. You can get it from NuGet. The package name is MvcReportViewer. The documentation and source code are available on GitHub under MIT license: https://github.com/ilich/MvcReportViewer. Bug reports, patches and other contributions are welcome!

  Read the article

• Are there any Linear Regression Function in MS SQL Server?

  - by pavanrao

  Are there any Linear Regression Function in SQL Server 2005/2008, similar to the the Linear Regression functions in Oracle ?

  Read the article

• Windows 2003 R2 x86 Mini dump fails to write to disk

  - by Randy K

  I have 3 blade servers that are Blue Screening with a 0xC2 error as far as we can tell randomly. When it started happening I found that the servers weren't set to do provide a dump because they each have 16GB RAM and a 16GB swap file divided over 4 partitions in 4GB files. I set them to provided a small dump file (64K mini dump), but the dump files aren't being written. On start up the server event log is reporting both Event ID 45 "The system could not sucessfully load the crash dump driver." and Event ID 49 "Configuring the Page file for crash dump failed. Make sure there is a page file on the boot partition and that is large enough to contain all physical memory." I understanding is the the small dump shouldn't need a swap file large enough for all physical memory, but the error seems to point to this not being the case. The issue of course is that the max swap file size is 4GB, so this seems to be impossible. Can anyone point me where to go from here?

  Read the article

• Whats the difference between local and remote addresses in 2008 firewall address

  - by Ian

  In the firewall advanced security manager/Inbound rules/rule property/scope tab you have two sections to specify local ip addresses and remote ip addresses. What makes an address qualify as a local or remote address and what difference does it make? This question is pretty obvious with a normal setup, but now that I'm setting up a remote virtualized server I'm not quite sure. What I've got is a physical host with two interfaces. The physical host uses interface 1 with a public IP. The virtualized machine is connected interface 2 with a public ip. I have a virtual subnet between the two - 192.168.123.0 When editing the firewall rule, if I place 192.168.123.0/24 in the local ip address area or remote ip address area what does windows do differently? Does it do anything differently? The reason I ask this is that I'm having problems getting the domain communication working between the two with the firewall active. I have plenty of experience with firewalls so I know what I want to do, but the logic of what is going on here escapes me and these rules are tedious to have to edit one by one. Ian

  Read the article

• SQL 2K5 - Multiple databases vs. Multiple files

  - by Bob Palmer

  Hey all, quick question. Our current legacy system was built using multiple distinct databases (about ten of them). These are all part of the same discreet system, and a large number of SPs and functionalty span multiple databases. There are also key relationships that span (for example, a header table may be in database A with history, etc. in database B). When deploying multiple copies of our app to the same server therefore, we have to use multiple instances (because the database names are coded into so many sprocs). We're evaluating the idea of taking these ten databases (about 30gb total with individual sizes ranging from 100mb to 10gb) and merging them into a single database. Currently, we have our databases spread accross multiple spindles for better IO. The question I have is whether or not there is any performance loss or benefit of having 10 different databases vs. 10 different database files? i.e. rather than having three databases (A, B, and C) Disk D: A.mdf (1gb) Disk E: B.mdf (4gb) Disk F: C.mdf (10gb) Disk G: A_Log.ldf, B_Log.ldf, C_Log.ldf have one database (X) Disk D: X1.mdf (5gb) Disk E: X2.mdf (5gb) Disk F: X3.mdf (5gb) Disk G: X1_log.ldf,X2_log.ldf,X3_log.ldf Thanks! -Bob

  Read the article

• How can a NodeJS server be used from Game Maker HTML5?

  - by Tokyo Dan

  I want to create a client-server game that runs on Game Maker HTML5-NodeJS. The NodeJS server will be an AI server - a bot that acts like a human opponent and plays against the human player at a front-end game client that is coded in GM HTML5. How can a NodeJS server be used from GM HTML5. Are there any examples of such a system? I already got an iOS game that can talk to a remote AI server (coded in Lua) using TCP sockets. Can this be done with Game Maker HTML5 and NodeJS.

  Read the article

• How to salvage SQL server 2008 query from KILLED/ROLLBACK state?

  - by littlegreen

  I have a stored procedure that inserts batches of millions of rows, emerging from a certain query, into an SQL database. It has one parameter selecting the batch; when this parameter is omitted, it will gather a list of batches and recursively call itself, in order to iterate over batches. In (pseudo-)code, it looks something like this: CREATE PROCEDURE spProcedure AS BEGIN IF @code = 0 BEGIN ... WHILE @@Fetch_Status=0 BEGIN EXEC spProcedure @code FETCH NEXT ... INTO @code END END ELSE BEGIN -- Disable indexes ... INSERT INTO table SELECT (...) -- Enable indexes ... Now it can happen that this procedure is slow, for whatever reason: it can't get a lock, one of the indexes it uses is misdefined or disabled. In that case, I want to be able kill the procedure, truncate and recreate the resulting table, and try again. However, when I try and kill the procedure, the process frequently oozes into a KILLED/ROLLBACK state from which there seems to be no return. From Google I have learned to do an sp_lock, find the spid, and then kill it with KILL <spid>. But when I try to kill it, it tells me SPID 75: transaction rollback in progress. Estimated rollback completion: 0%. Estimated time remaining: 554 seconds. I did find a forum message hinting that another spid should be killed before the other one can start a rollback. But that didn't work for me either, plus I do not understand, why that would be the case... could it be because I am recursively calling my own stored procedure? (But it should be having the same spid, right?) In any case, my process is just sitting there, being dead, not responding to kills, and locking the table. This is very frustrating, as I want to go on developing my queries, not waiting hours on my server sitting dead while pretending to be finishing a supposed rollback. Is there some way in which I can tell the server not to store any rollback information for my query? Or not to allow any other queries to interfere with the rollback, so that it will not take so long? Or how to rewrite my query in a better way, or how kill the process successfully without restarting the server?

  Read the article

• How to allow multiple users to manage application running on server?

  - by Mary-Chan

  I'm not sure if the title makes sense. Hard question to ask. I have an application running on a server under my network account, and it's scheduled to run daily. I can remote in with my user credentials and check on the application. What if I want more than one person to be able to remote in and check it? I can create a new account on the server, but it wouldn't have network rights and the application needs access to network folders. What would be the best approach? Thanks! :-) P.S. Feel free to edit the tags. I can't figure out what to pick.

  Read the article

• Web App Server hardware question. Which configuration?

  - by JBeckton

  I am pricing some new servers and I am not sure which configuration to get. The server will be running some web applications for our company. Some of them are ASP.Net sites and some are ColdFusion. The OS will be Win Server 2008 Web or Standard Edition. Do I need 2 processors or will a single quad core handle it? Xeon multi core Hyperthreading or non Hyperthreading? I am going 64bit so I can go higher than 4 Gigs of Ram. I am shopping at Dell and there are so many options, i do not want to get too much hardware and not use half of it because that would be a waste of money and I do not want to get too little and have to ask for more money to upgrade it later.

  Read the article

• How can I turn a bunch of rows into aggregated columns WITHOUT using pivot in SQL Server 2005?

  - by cdeszaq

  Here is the scenario: I have a table that records the user_id, the module_id, and the date/time the module was viewed. eg. Table: Log ------------------------------ User_ID Module_ID Date ------------------------------ 1 red 2001-01-01 1 green 2001-01-02 1 blue 2001-01-03 2 green 2001-01-04 2 blue 2001-01-05 1 red 2001-01-06 1 blue 2001-01-07 3 blue 2001-01-08 3 green 2001-01-09 3 red 2001-01-10 3 green 2001-01-11 4 white 2001-01-12 I need to get a result set that has the user_id as the 1st column, and then a column for each module. The row data is then the user_id and the count of the number of times that user viewed each module. eg. --------------------------------- User_ID red green blue white --------------------------------- 1 2 1 2 0 2 0 1 1 0 3 1 2 1 0 4 0 0 0 1 I was initially thinking that I could do this with PIVOT, but no dice; the database is a converted SQL Server 2000 DB that is running in SQL Server 2005. I'm not able to change the compatibility level, so pivot is out. How can I accomplish this?

  Read the article

• Msg 10054, Level 20, State 0, Line 0 Error when altering a stored procedure to add a couple of curso

  - by doug_w

  We have a home-rolled backup stored procedure that uses xp_cmdshell to create and clean up database backups. We have an instance that is 2005 sp3 that we are trying to deploy this script to. I am at a bit of a loss for why it is not working. When I execute the create it runs for about 30 seconds and yields the following error: Msg 10054, Level 20, State 0, Line 0 A transport-level error has occurred when sending the request to the server. (provider: TCP Provider, error: 0 - An existing connection was forcibly closed by the remote host.) In my tinkering I discovered that by removing the cursors that actually do the work it will allow me to create the stored procedure (not very helpful for me though). If I add the cursors back in using an alter the error returns. I would be curious if someone has experienced this problem and knows of a solution or work around. I am not opposed to posting the source, it is just lengthy. Things I have checked: Error Logs No dump files in the log directory Thanks in advance for the help.

  Read the article

< Previous Page | 210 211 212 213 214 215 216 217 218 219 220 221  | Next Page >