Search Results

Search found 7583 results on 304 pages for 'roger guess'.

Page 216/304 | < Previous Page | 212 213 214 215 216 217 218 219 220 221 222 223  | Next Page >

• Router as primary DNS server, Server as alternate? (or vice versa)

  - by Jakobud

  We have a very small business network, with a typical cable modem hooked into a DD-WRT router. We also run a basic CentOS server that does a variety of things, including acting as the primary DNS server for the office. The reason we need an internal DNS server is because we do a lot of internal web development and use the DNS server to add/remove various local network URLs for internal website testing (like www.testsite.com.local). It's very important for us to be able to add/remove URL aliases easily to the DNS. The problem with this setup is that if we ever need to restart the CentOS server or take it offline for upgrades or whatever, then internet access for all computers on the network is lost. That's because each computer relies on that DNS server to access the Internet I guess? The router is online all the time and very very rarely has to be restarted. It would be nice if we could setup my router to be the primary DNS server but still be running DNS on my server. So we could still add my local testing website URLs to the DNS server in CentOS, but be able to also take down the CentOS server without loosing Internet access on the network. How would this be setup? Would I simply need to add both router + server IP addresses to each computer's IP settings? Is the router primary DNS and server secondary DNS server? Or vice versa? Or can one of the two serve as a fallback for the other? What (if anything) needs to be configured on both the router and server in order for them to recognize that the other DNS server exists on the network? Does anyone have any newb-friendly resources for setting up something like this?

  Read the article

• Exchange 2010 mail routing with Hub Transport in multiple sites

  - by jmreicha

  I have two separate physical sites, Site A and Site B. In site A, I have following: 2 CAS servers 2 Hub Transport servers 2 Mailbox servers 2 Edge servers In site B, I have the following: 1 CAS 1 Hub 1 Mailbox 1 Edge Currently everything is working out of site A. That is, all users are housed on mailboxes that are in site A and all inbound mail flow is pointing to site A. I would eventually like to be able to move some of the mailboxes to site B without causing a disruption for resliency and redundancy purposes but I am not quite sure how to go about setting this up or if it is even possible. So far I have created an Edge subscription in site B and am able to send emails out from test accounts set up with mailboxes on the site B Mailbox server. However, I am unable to receive incoming mail messages and am confused. So I'm thinking incoming mail messages are still being directed to site A and then they are getting stuck because there is no way to route the mail to the site B mailboxes. Is this assumption correct? I am unfamiliar with mail flow and routing so I am not really sure what I need to be looking at? Would I add the site B hub transport to the Edge subscription in site A? Or I guess more specifically, how would I go about enabling communication and mail flow between mailboxes split up on site A and B?

  Read the article

• Setting up test an dlive enviornment - how?

  - by Sean

  I am a bit new to servers and stuff so had a question. I have my development team working on my website. They are in different countries and currently they put all the work live on the test site. But the test site is open to anyone who knows the URL. It is behind a directory but this effects my QA process because i cannot use the accurate URL structures to prevent the general public from seeing it. So what I want to do it: Have my site live on the net but only for me and my team, so like an internal network. Also I will need to mirror this to my live site when i put it live. So i guess this is something like setting up a staging and live environment. So how to do it and are both environments on the same physical server or do i need to buy two servers? And if i setup a staging environment how will i access it and my team since we are all spread out so i assume we need to log into something to access it? What about the URL - do i need a different URL for the test site or can i use the same live url for the test site? I plan to get a dedicated server + CDN for my site.

  Read the article

• How to find out which process is hogging the linux server?

  - by user1149518

  We have a RHEL server. Today it suddenly became slow. Symptoms - It was responding slow to ping queries from other server. When I try to login using ssh, it was taking about 10 seconds to login. I was able to resolve the problem by doing some guess work. I killed one process which I thought was culprit. Which resolved the problem. Though I would like to know what's proper approach to detect the culprit in such kind of "slow server" situations. Le me know proper way to resolving such slowness issues and decting the process causing the slowness. These were the conditions when the server was slow - # vmstat 3 3 procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu------ r b swpd free buff cache si so bi bo in cs us sy id wa st 1 1 176 6730868 285052 4899676 0 0 3 4 0 0 1 1 97 1 0 0 0 176 6751576 285064 4899704 0 0 0 115 15307 37171 1 1 96 3 0 0 0 176 6751948 285068 4899700 0 0 0 23 14813 39559 1 1 98 1 0 # top top - 16:38:18 up 150 days, 19:36, 64 users, load average: 1.68, 1.46, 1.44 Tasks: 1287 total, 2 running, 1284 sleeping, 1 stopped, 0 zombie Cpu(s): 1.3%us, 1.7%sy, 0.1%ni, 95.9%id, 0.7%wa, 0.0%hi, 0.2%si, 0.0%st Mem: 16620824k total, 9867124k used, 6753700k free, 287424k buffers Swap: 8193140k total, 176k used, 8192964k free, 4898996k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 26258 khk 34 19 130m 47m 7088 S 11.2 0.3 385:32.42 edm Though I would like to know what's proper approach to detect the culprit in such kind of "slow server" situations. Le me know proper way to resolving such slowness issues and decting the process causing the slowness.

  Read the article

• Logging communication between two VMs

  - by sYnfo

  Hi, I'm trying to set up "malware lab" described in this paper. So far, I've set up Windows guest system, adding one Host-only Network adapter, and setting this (sorry if the names aren't exactely correct, I don't have an english language version): - IP Address - 10.0.0.3 - Subnet mask - 255.255.255.0 - Default gateway - not set - Preferred DNS - 10.0.0.4 - Alternate DNS - not set And a Linux guest system - Ubuntu 9.04 - with two Network adapters - Bridged (eth0) and Host-only (eth1), and setting eth1 IP Address to 10.0.0.4, leaving the eth0 to be set by DHCP. Then, I have configured iptables as described in the paper, ie.: iptables -F -t nat iptables -F -t mangle iptables -t mangle -P PREROUTING ACCEPT iptables -t mangle -P OUTPUT ACCEPT iptables -t nat -P PREROUTING ACCEPT iptables -t nat -P POSTROUTING ACCEPT iptables -t nat -P OUTPUT ACCEPT iptables -t mangle -A PREROUTING -i eth0 -j ACCEPT iptables -t mangle -A PREROUTING -p udp -i eth1 -d 10.0.0.3 --dport 53 -j ACCEPT iptables -t mangle -A PREROUTING -p tcp -i eth1 --dport 80 -j ACCEPT iptables -t mangle -A PREROUTING -p tcp -i eth1 -d 10.0.0.3 --dport 6000:7000 -j ACCEPT iptables -t mangle -A PREROUTING -i eth1 -j ULOG iptables -t mangle -A PREROUTING -i eth1 -j DROP Now, when I try to ping the windows system from within the Linux system, it does not reply, I guess thats perfectly normal, because iptables is blocking ping responce. Same when I try to ping the Linux system from within the Windows. But when I try to access any web page from within the Windows system, I would expect that this action should get logged by iptables. But thing is, I don't see any of that kind of lines in log file (If I am looking in the right place, that is. :) It is at /var/log/messages, isn't it?). So, what do you think might be the problem here? I should note, that this is the first time I'm using linux, so don't expect ANY working knowledge of Linux at all... :) Also, since english is not my mother tongue, feel free to point out any gramatical mistakes... :) Thanks for any advice.

  Read the article

• Ubuntu server 10.04 disconnects after short periods of inactivity on my site

  - by user57019

  I'm new to Ubuntu (installed it for the first time just a couple of days ago on my server). I've Ubuntu Server 10.04 and am just using the terminal, no GUI like Gnome. So far it's working pretty great except for one big thing. Whenever I go to sleep and there's no activity on my server (it's not a big site so active users drop to 0 during the night), the server kind of disconnects. The only thing that can bring the site back online is to restart the whole server. I've tried disabling powersaving by using setterm but that changes nothing. Even if I wake up the server by pressing any key or so the site wont go back online! I've tried just restarting both Apache and MySQL (I'm using LAMP-server btw) but not even that works. But as soon as I turn the power off and on at the server, everythings work like normal for a couple of minutes of inactivity (~5-15 minutes I'd guess) and then it's down again unless someone logs in to the site and is active. I was previously using XAMPP on my laptop with Windows XP and that worked 24/7 so I don't think it's anything with my router or ISP. This is driving me crazy! My site is down all the time I'm in school as I have no possibility to restart the server if it becomes offline. Does anyone have a clue to what could be wrong?

  Read the article

• Partitioning of Ubuntu server which will use OpenVZ and encrypted partitions (unlocked through SSH l

  - by DeletedAccount

  Hi, I'm about to install a server. Some context: My HDD is 1 TB and I have 2 GB RAM Ubuntu Server Lucid Lynx AMD 64 I will use OpenVZ and have most functionality separated into containers. To support disk quotas I need to use ext3 (not ext4) for the container partition. Each time I reboot the server I want to be forced to login through SSH and mount the encrypted partitions by typing my password (if someone steals the server, no critical data should be available). I want to have as much as possible encrypted. Yet I want to be able to login through SSH as I don't have a monitor or keyboard at the server. I am not sure how big I need my partitions to be. Being able to resize them later would be nice. I guess it implies using LVM? But the manual partition mount using SSH is also very important (in fact it's more important, if I have to pick one). How do you recommend that I partition the HDD? If I have daemons which needs the encrypted partitions, will they fail and can I just restart them after mounting the needed partitions?

  Read the article

• Windows Server 2008 R2 grinds to a screeching halt during file copy operations

  - by skolima

  When my Windows Server 2008 R2 machine is performing any large disk operations (copying 10GB files from one drive to another, copying similar file over network, merging HyperV snapshots, compressing large files), performance of the whole machine slows down terribly, everything becomes unresponsive. This is noticeable in any situation when the disk access is large enough not to fit in the cache. Are there any settings available for tuning this behaviour? I can accept slower file transfer if this would give me more responsiveness. System details: Dell Optiflex 960, Core 2 Quad Q9650, 8GB RAM, 2 SATA drives - 320GB (ST3320418AS) and 1TB (ST31000528AS), NCQ active on both, Intel 82564LM-3 Gigabit Ethernet, ATI HD 3450 graphics, Intel ICH10 bridge. We have multiple machines like this, every one is exhibiting the same behaviour. I though this was overkill for a workstation, apparently I was mistaken. Update: I guess I shouldn't have mentioned the HyperV at all. The above configuration is a standard workstation setup at the company I work for, this is not a server of any kind. I have at most 3 virtual machines working, and usually I'm the only person accessing them. Never the less, the slowdown occurs even when no VMs are running. On a Linux machine I'd simply ionice the copy process and I could forget about it, is there any way to manage IO priorities on Windows?

  Read the article

• Same script, different behavior [migrated]

  - by Antoine_935

  I just stumbled upon an interesting bug... Still trying to figure out what is exactly happening. Maybe you can help. First, the context. I'm currently building yet another man to html converter (for some reasons I won't motivate here, but I need it). So, have a look at the screenshot below (see the link), more precisely at the outlined spots. See? On the upper shell, I have &lt ; and &gt ;, that is, escaped html. While on the shell below I have < and directly. But as you can see (or do I seriously need looking glass ?), the command man 2 semget | webmanneris the same on both sides, as is the which webmanner. The two are executed roughly at the same moment, with no modification made to the script between. [Oops, cannot post pictures just yet... Here comes the link] http://aspyct.org/media/webmanner-bug.png But the shell below is older (open about 1 hour ago). Newer shells all print out &lt ;. So my first guess was that it somehow had a cached reference to the old inode of the file, or old blocks or whatever. So I modified parts of the script, at the start and then at the end, to print different messages. And, surprise, the message shown up on both terminals. But still, same difference between &lt ; and <. I'm confused... How to explain that behavior? I'm working on a OSX 10.8 (Mountain Lion) EDIT: OK, there is one big difference: the shell below uses ruby 1.9.3, while above is 1.8.7. Is there any known difference in string handling between the two versions ?

  Read the article

• Reading log files from web application

  - by Egorinsk

  Hi! I want to write a small PHP application for monitoring logs on a Debian server, including syslog logs and Apache/PHP messages. The problem here is that Apache user (www-data) has no access to /var/log directory. What would be the best way to grant an access to logs for PHP application? Let's assume that log files can be really large, like hundreds of megabytes. I have some ideas: Write a shell script that would be run via sudo and tail last 512 Kb of log into a separate file that can be read by application - that's ineffective, because of forking a new process and having to read data twice Add www-data to adm group (that can read logs) - that's insecure Start a PHP process via cron every minute to read logs — that's not very good, because it doesn't allow real-time monitoring. Also, this script will be started even when I don't read logs, and consume CPU time (server is in the cloud, and I'll have to pay for it) Create a hardlink for all log files with lowered permissions - I guess, that won't work because logrotate could recreate log files and they'll change inode number. Start a separate nginx/Apache server under privileged user that may read logs. Maybe anyone got a better solution?

  Read the article

• Should I update the kernel on a Linux machine?

  - by Legate

  As I understand it, updating to a new kernel (with the normal linux-image... package, not by rolling my own) requires a server restart. However, one of our servers (Ubuntu 10.04) is running several extensive screen sessions. Restarting kills those which is always a major hassle to their owners (mostly because of lost session histories). What should I do? I see several possibilites: Not doing anything, that is update only non-kernel packages (perhaps use apt-pinning?) Update the kernel, but not restart. (Is that smart? I seem to remember there might be some problems with loading kernel modules.) Updating the kernel and restarting. Is there perhaps some way to preserve the screen sessions? I guess it ultimately boils down to this question: How important is it to update the kernel? I posted this question here instead of askubuntu.com as I think this is not an Ubuntu-specific issue though this server is running Ubuntu.

  Read the article

• Change the logical name of sql server express 2005 database file?

  - by oob

  In Microsoft SQL Server Management Studio Express for Sql Server Express 2005, I needed to copy a database for testing and keep it on the same server as the old database. I did the following: Right Click on Databases Created new database Detached the database I wanted to copy "Restored" my new database from the backup file of my old database. I did this by clicking the 'Overwrite the existing database' box on the Options pane, and I changed the paths in the 'restore as' options so that they pointed to my new .mdf and .ldf files. Everything is working like I want. Problem is, when I right-click - Properties - Files on my new database, the logical name of the .mdf file is the same as the logical name of the old .mdf file. They are actually different files - they just share the same logical name? I guess maybe this isn't a short-term problem, but I can see it confusing somebody down the road. Any way to change the logical name of the .mdf file? UPDATE EDIT - Apparently you can just change the logical name through the GUI by, get this, clicking on it and typing a new name. I could swear that was not possible when I posted this, but maybe it was and I somehow missed it! Either way - the solution below should still work but doing it through the GUI is also an option.

  Read the article

• ec2 spot instance for daily processing task

  - by chaft

  I don't have much experience as a sysadmin or with amazon aws, so I hope someone can explain in simple terms or refer me to a good guide on how to achieve the below. I have a system running on ec2 and amazon rds getting data in and saving it to the db. I need to run a script once a day (at the end of the day) to process all that data and prepare a daily report. This process will take approximately an hour to run. It needs to run on a high memory instance.. From what i've read so far, I guess the best way to do it is to have a high memory spot instance run every day, set it up to execute the script on startup and and shut down when done. Is that the right way to do it? If so, how to do it? how to tell the spot instance to run every day? through a cron job on the other server or is there a better way? How to set it up to run the script on startup? through cloudinit? Any help would be appreciated. One last thing, the job is not very time sensitive as long as it runs every day.. thanks

  Read the article

• How to fix missing RAID1 drive

  - by Sodved

  I had to do some fiddling about with my cables inside thebox and now I am getting a "Critical Error" about the RAID disks during startup. I have a gigabyte GA-MA770T-UD3 motherboard. Aparently the RAID controller is an AMD SB710 chip. I'm pretty sure I know what happenned. The first time I rebooted I had forgotten the power cable on one of the disks in the RAID1 (mirror) and let it boot up. So I shut down and put the power back in. So now when it boots up I go into the RAID admin interface (between the BIOS screen and the OS loading): it shows the RAID1 as in error the logical device has one disk and says the other is disconnected or missing the other physical disk shows up as a single disk If I boot to the OS (Windows 7 32 bit) the data all seems to be there. If I go into computer management it says my partition is on a disk and working OK. But the other disk is offline because: "The disk is offline because it has a signature collision with another disk that is online" So I am guessing because I STUPIDLY booted up with only one of the disks powered on, the other disk fell out of synch with the mirror and so now cannot rejoin the mirror. How do I fix this? I want to get the RAID1 mirror working again. There does not appear to be any "Repair" option in the basic RAID admin tool which I get into during startup before the OS boots. I have not made any explicit changes to the online one (but I guess the OS has probably written some admin data).

  Read the article

• Ubuntu server 10.04 disconnects after short periods of inactivity on my site

  - by Melot

  Hi! I'm new to Ubuntu (installed it for the first time just a couple of days ago on my server). I've Ubuntu Server 10.04 and am just using the terminal, no GUI like Gnome. So far it's working pretty great except for one big thing. Whenever I go to sleep and there's no activity on my server (it's not a big site so active users drop to 0 during the night), the server kind of disconnects. The only thing that can bring the site back online is to restart the whole server. I've tried disabling powersaving by using setterm but that changes nothing. Even if I wake up the server by pressing any key or so the site wont go back online! I've tried just restarting both Apache and MySQL (I'm using LAMP-server btw) but not even that works. But as soon as I turn the power off and on at the server, everythings work like normal for a couple of minutes of inactivity (~5-15 minutes I'd guess) and then it's down again unless someone logs in to the site and is active. I was previously using XAMPP on my laptop with Windows XP and that worked 24/7 so I don't think it's anything with my router or ISP. This is driving me crazy! My site is down all the time I'm in school as I have no possibility to restart the server if it becomes offline. Does anyone have a clue to what could be wrong?

  Read the article

• Messages don’t always appear in Mail.app

  - by MikeHoss

  I asked this question on serverfault, but it was correctly suggested that superuser is better -- and I agree: My wife and I share a Mac and use different accounts. We both use Apple's standard Mail.app. We can also get to our email accounts via SquirrelMail that our webhost provides. Both SquirrelMail and Mail.app are connecting via IMAP. My wife was the first to notice that not all messages were getting to the Mail.app. She would check the Mac (our main machine) and then a little while later check mail from another machine via SquirrelMail and see messages there that should have been on the Mac. She would go back and those messages would never show up. Lately, I have been seeing the same thing, though less often. I can't reproduce it, or just look at a message to see if they haven't been moved over. I've looked in Junk, etc. and the Mac simply never sees those messages via IMAP. Does anyone have a guess to something I could poke around at?

  Read the article

• Always maximize almost maximized window utility

  - by AbstractDissonance

  It drives me nuts when a window is nearly maximized but not quite and when I go to close/move/scroll it I end up bringing up the window behind it. This happens all the time with acrobat. It seems that it's default non-minimized state is usually an "almost" maximized windowed. Is there any utility that will maximize a window when it is open or size changed when it is near the size of the monitor. I'll never have any need to have a window 99% the size of the window with it centered. Why? Because it behaves just as a maximized window by obscuring all(well, almost all) the windows behind it. (It should be only the main window of an application that is affected) The issue seems to be a few programs like acrobat that, I guess, try to fit it's contents which, sometimes, happens to be almost the full screen but not quite making it look maximized when it is not. I do not want all windows to open maximized but have no need for the window state almost centered and almost the same size as the desktop. (I imagine most people don't)

  Read the article

• Optimize Apache performance

  - by Phliplip

  I'm looking for ways to optimize our current web server hosted in-house. I'm trying to supply as much relevant information below. Please let me know if you would require additional information in order to assist. Server is running 1 single website, which is an online pizza ordering platform built on Zend Framework (ver1). On traffic stats from the last month aprox 6.000 pageloads per day, concentrated mainly around dinnertime. Around 1500 loads/hour peaks in that period. We recently upgraded from a 2/2mbit aDSL-line to 100/100mbit fiber, and we still have performance issues at dinner time. We assumed the 2mbit was the issue. Website is pretty snappy in low-load periods. Hardware CPU: Intel(R) Xeon(R) CPU 5160 @ 3.00GHz (3000.13-MHz K8-class CPU) Mem: 328M Active, 4427M Inact, 891M Wired, 244M Cache, 623M Buf, 33M Free Swap: 16G Total, 468K Used, 16G Free (6GB physical, 16GB swap) Filesystem Type Size Used Avail Capacity Mounted on /dev/ad7s1a ufs 4.8G 768M 3.7G 17% / devfs devfs 1.0K 1.0K 0B 100% /dev /dev/ad7s1g ufs 176G 5.2G 157G 3% /home /dev/ad7s1e ufs 4.8G 2.8M 4.5G 0% /tmp /dev/ad7s1f ufs 19G 3.5G 14G 19% /usr /dev/ad7s1d ufs 4.8G 550M 3.9G 12% /var Server OS FreeBSD 8.2-RELEASE Software apache-2.2.17 php5-5.3.8 mysql-server-5.5 Apache footprint (example, taken from # top) 31140 www 1 45 0 377M 41588K lockf 2 0:00 0.00% httpd 31122 www 1 44 0 375M 35416K lockf 2 0:00 0.00% httpd 31109 www 1 44 0 375M 38188K lockf 2 0:00 0.00% httpd 31113 www 1 44 0 375M 35188K lockf 2 0:00 0.00% httpd Apache is using the prefork MPM, APC (Alternative PHP Cache). SSL module is loaded, but not utilized (as in don't really work, thus not used). There is a file containing settings for MPM modules, but as i see it's not included in the httpd.conf file, the include line is commented out. Thus i would guess that the prefork MPM is working of default values too. Here are some other Apache conf values that i found - which are included in https.conf Timeout 300 KeepAlive On MaxKeepAliveRequests 100 KeepAliveTimeout 5 UseCanonicalName Off HostnameLookups Off

  Read the article

• Which scripting language to use to asynchronously ssh into equipment, run several commands, parse the output, and save to a file on my computer?

  - by Fujin

  There are several points I'd like to stress in my question. I'd like to login by asynchronously ssh'ing into our infrastructure equipment. Meaning, I do not want to connect to only one device, do all the tasks I need, disconnect, then connect to the next device. I want to connect to several devices at once in order to make the process as fast as possible. By equipment I mean 'infrastructure equipment' and not servers. I say this because I will not have the luxury of saving files to the device then transferring them to myself with scp or another method. The output of the scripts that are run will have to be saved directly to my computer. The output of the commands that are run will need to be cleaned up and parsed. Also I want the outputs of each device to be combined into one nice and neat file, not a separate file for each device. This will all be done from a linux box, using ssh, into devices that all use linux'ish proprietary OSes. My guess is the answer to my question will either be a Bash, Perl, or Python script but I figured it wouldn't hurt to ask and to hear the reasons why one way is better than another. Thanks everyone. EXTRA CREDIT: With you answer, include links to resources that will help create the script I described in the language that you suggested.

  Read the article

• Auto-restart mysql when it dies

  - by Los Frijoles

  I have a rackspace server that I have been renting to run my personal projects upon. Since I am cheap, it has 256Mb of RAM and honestly can't handle alot. Every once in a while, when there is a sharp uptick in traffic, the server decides to start killing processes and it seems that mysqld is a popular one for it to kill. I try to visit my site and am greeted with the message that there was an error establishing the database connection. Inspection of the logs reveals that mysqld was killed due to lack of memory. Since I am still as poor as I was yesterday and don't want to upgrade my rackspace VM's RAM, is there a way I can tell it to automagically restart mysqld when it dies? I have a thought to use something like crontab, but alas, I don't know exactly what to do there either. I guess I am product of the "Linux on your desktop" generation since I can do most things on my desktop and laptop (which run Linux almost exclusively), but still lack a lot of server administration skills for Linux. The server runs CentOS 6.3

  Read the article

• Things to consider when building a continuous integration server?

  - by Dave

  I'm new to continuous integration, but immediately realize its value, and I want to get one set up right away. I have played with TeamCity and have it working in a VM great. Now, I don't want to spend money on another system, so I was planning on just doing the VM again on a faster machine (i.e. my dev system). There are a few questions that come to mind with this: Hard disk allocation - how big should it be? Sure, 60GB seems like more than enough, but people also used to think that we'd never need more than 64KB of RAM Backups - is it even important to back up the integration server? Sure, I guess it's nice so that one doesn't have to go through the entire configuration process again, but I would think that's about it. I could snapshot my VM every time I do a configuration change, and then do a backup of applications only (ignore the buildAgent stuff). Migration - if I want to go away from a VM on my dev system, to a new server, which maybe even runs Windows Server 2003, is it easy enough? Perhaps this is a particular point best suited for StackOverflow.

  Read the article

• RedStation.com is heaven for ddos attackers, How to file complaint?

  - by Ehsan

  Sorry, I don't know where to open this subject. This is not the first time we have faced with a massive DDOS attack from one of servers in RedStation.com and even after we had contacted with their abuse department with it's log there is no cooperation and they don't even like to bother themselves about it. and we don't know how to stop such activity. Do you know how to file complaint against this datacenter? we could not be patient anymore and see they are not care about such things on their network ? it seems like they are heaven for attackers now since they close their eyes to gain more money. I guess some global organization is missing in this matter to investigate such activity and make sure providers are responsible for their services. Here is some of it's log: 2686M 75G DROP all -- * * 31.3-RedStation 0.0.0.0/0 rt: 16167 0.002007 31.3-RedStation -> my-server-ip UDP Source port: 36391 Destination port: 16167 0.002011 31.3-RedStation -> my-server-ip UDP Source port: 38367 Destination port: 16312 0.002014 31.3-RedStation -> my-server-ip UDP Source port: 39585 Destination port: 12081 0.002018 31.3-RedStation -> my-server-ip UDP Source port: 39585 Destination port: 12081 0.002021 31.3-RedStation -> my-server-ip UDP Source port: 38367 Destination port: 16312 0.002025 31.3-RedStation -> my-server-ip UDP Source port: 39585 Destination port: 12081 0.002033 31.3-RedStation -> my-server-ip UDP Source port: 36391 Destination port: 16167 0.002037 31.3-RedStation -> my-server-ip UDP Source port: 38367 Destination port: 16312 0.002040 31.3-RedStation -> my-server-ip UDP Source port: 38367 Destination port: 16312 0.002044 31.3-RedStation -> my-server-ip UDP Source port: 38367 Destination port: 16312 0.002047 31.3-RedStation -> my-server-ip UDP Source port: 39585 Destination Any response would be appreciated

  Read the article

• How many guesses per second are possible against an encrypted disk? [closed]

  - by HappyDeveloper

  I understand that guesses per second depends on the hardware and the encryption algorithm, so I don't expect an absolute number as answer. For example, with an average machine you can make a lot (thousands?) of guesses per second for a hash created with a single md5 round, because md5 is fast, making brute force and dictionary attacks a real danger for most passwords. But if instead you use bcrypt with enough rounds, you can slow the attack down to 1 guess per second, for example. 1) So how does disk encryption usually work? This is how I imagine it, tell me if it is close to reality: When I enter the passphrase, it is hashed with a slow algorithm to generate a key (always the same?). Because this is slow, brute force is not a good approach to break it. Then, with the generated key, the disk is unencrypted on the fly very fast, so there is not a significant performance lose. 2) How can I test this with my own machine? I want to calculate the guesses per second my machine can make. 3) How many guesses per second are possible against an encrypted disk with the fastest PC ever so far?

  Read the article

• How to diagnose a spontaneous reboot?

  - by Spectralist

  My computer reboots, seemingly completely at random, about once every week to two weeks but has occasionally gone months. It just goes from running fine to the POST with no error messages or anything and doesn't seem to be due to heat or usage as it's happened a couple of times when the computer has booted just a few moments ago and is idling. It's been happening for as long as I've had this computer, almost two years. It's happened in both Vista and Windows7. I strongly suspect it's a hardware problem. But due to the rareish and random nature of the crashes my normal strategy of just removing hardware until the problem stops isn't really practical. My guess would be Power Supply, Ram, or Motherboard. But I just don't know how to test an issue this random and want to figure out how to confirm which it is before I go replacing things. So is there some software or hardware that can be used to test these sorts of errors? I did run memtest86 for about 8 hours without finding any issues. And the power supply is more than capable of running my system.

  Read the article

• Windows 7 delayed file delete

  - by GregoryM

  I'm stuck with a pretty rare problem that happens on Windows 7 OS only. Every time I'm deleting the file with *.exe extension through explorer, the file doesn't get deleted immediately. I'm forced to wait for around one-two minutes before the system will delete the file. The main problem is that I cannot develop in such situation, because every time I build my solution, the old executable gets 'deleted', but is still there. So the new one cannot be created by Visual Studio. This problem breaks the Steam update progress and a few other installers functionality too. Fresh installed Win7 doesn't have this kind of trouble, so I guess this must be some bad registry entries or some services. Browsing the internet for solutions I found only this: http://www.sevenforums.com/software/72091-several-minute-delay-when-deleting-any-exe-file.html. But the solution the author found is not working (change the userName :)). Is there any ideas how to find what causes this to happen? BTW: when I place the file into Trash bin, no delay occurs. When I delete file with Total Commander - no delay too. Tech details: Windows 7 x64 Ultimate.

  Read the article

< Previous Page | 212 213 214 215 216 217 218 219 220 221 222 223  | Next Page >