Search Results

Search found 11313 results on 453 pages for 'ip aliasing'.

Page 217/453 | < Previous Page | 213 214 215 216 217 218 219 220 221 222 223 224  | Next Page >

• network is not available even when cisco vpn client is connected. wrong route?

  - by javapowered

  I'm using Vodafone 3G modem. I've disabled other network devices in the system (ethernet, wifi, wimax) turned off firewall and antivirus. cisco vpn client connects successfully but I still can not access computer 192.168.147.120 (as well as any other computer from network). Any suggestions are welcome as I don't know what to do. ipconfig /all and route print commands (translated to english): Microsoft Windows [Version 6.1.7601] (C) Microsoft Corporation (Microsoft Corp.), 2009. All rights reserved. C: \ Users \ Oleg> ipconfig / all IP Configuration for Windows The name of the computer. . . . . . . . . : OlegPC The primary DNS-suffix. . . . . . : Node Type. . . . . . . . . . . . . : Hybrid IP-routing is enabled. . . . : No WINS-proxy enabled. . . . . . . : No Ethernet adapter Local Area Connection 4: DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Cisco Systems VPN Adapter Physical Address. . . . . . . . . 00-05-9A-3C-78-00 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes Local IPv6-address channel. . . : Fe80:: c073: 41b2: 852f: eb87% 26 (Preferred) IPv4-address. . . . . . . . . . . . : 10.53.127.204 (Preferred) The subnet mask. . . . . . . . . . : 255.0.0.0 Default Gateway. . . . . . . . . : IAID DHCPv6. . . . . . . . . . . : 536872346 DUID the client DHCPv6. . . . . . . 00-01-00-01-14-6F-4C-8D-60-EB-69-85-10-2D DNS-servers. . . . . . . . . . . : Fec0: 0:0: ffff:: 1% 1 fec0: 0:0: ffff:: 2% 1 fec0: 0:0: ffff:: 3% 1 NetBios over TCP / IP. . . . . . . . : Disabled Adapter mobile broadband connection through a broadband adapter mobile communications: DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Vodafone Mobile Broadband Network Adapter (Huawei) Physical Address. . . . . . . . . 58-2C-80-13-92-63 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes IPv4-address. . . . . . . . . . . . : 10.229.227.77 (Preferred) The subnet mask. . . . . . . . . . : 255.255.255.252 Default Gateway. . . . . . . . . : 10.229.227.78 DNS-servers. . . . . . . . . . . : 163.121.128.134 212.103.160.18 NetBios over TCP / IP. . . . . . . . : Disabled Tunnel adapter isatap. {737FF02E-D473-4F91-840E-2A4DD293FC12}: State of the environment. . . . . . . . : DNS Suffix. DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Adapter Microsoft ISATAP # 3 Physical Address. . . . . . . . . 00-00-00-00-00-00-00-E0 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes Tunnel adapter isatap. {EF585226-5B07-4446-A5A4-CB1B8E4B13AC}: State of the environment. . . . . . . . : DNS Suffix. DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Adapter Microsoft ISATAP # 4 Physical Address. . . . . . . . . 00-00-00-00-00-00-00-E0 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes Tunnel adapter Teredo Tunneling Pseudo-Interface: DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physical Address. . . . . . . . . 00-00-00-00-00-00-00-E0 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes IPv6-address. . . . . . . . . . . . : 2001:0:4137:9 e76: ea: b77: f51a: 1cb2 (Basically d) Local IPv6-address channel. . . : Fe80:: ea: b77: f51a: 1cb2% 16 (Preferred) Default Gateway. . . . . . . . . ::: NetBios over TCP / IP. . . . . . . . : Disabled C: \ Users \ Oleg> route print ================================================== ========================= List of interfaces 26 ... 00 05 9a 3c 78 00 ...... Cisco Systems VPN Adapter 23 ... 58 2c 80 13 92 63 ...... Vodafone Mobile Broadband Network Adapter (Huawei) 1 ........................... Software Loopback Interface 1 19 ... 00 00 00 00 00 00 00 e0 Adapter Microsoft ISATAP # 3 20 ... 00 00 00 00 00 00 00 e0 Adapter Microsoft ISATAP # 4 16 ... 00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface ================================================== ========================= IPv4 Route Table ================================================== ========================= Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.229.227.78 10.229.227.77 296 10.0.0.0 255.0.0.0 On-link 10.53.127.204 286 10.6.93.21 255,255,255,255 10.0.0.1 10.53.127.204 100 10.13.50.12 255,255,255,255 10.0.0.1 10.53.127.204 100 10.53.8.0 255.255.252.0 10.0.0.1 10.53.127.204 100 10.53.127.204 255.255.255.255 On-link 10.53.127.204 286 10.53.128.0 255.255.248.0 10.0.0.1 10.53.127.204 100 10.53.148.0 255,255,255,240 10.0.0.1 10.53.127.204 100 10.53.148.16 255,255,255,240 10.0.0.1 10.53.127.204 100 10.229.227.76 255.255.255.252 On-link 10.229.227.77 296 10.229.227.77 255.255.255.255 On-link 10.229.227.77 296 10.229.227.79 255.255.255.255 On-link 10.229.227.77 296 10.255.255.255 255.255.255.255 On-link 10.53.127.204 286 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.147.0 255,255,255,240 10.0.0.1 10.53.127.204 100 192.168.147.96 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,112 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,128 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,144 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,224 255,255,255,240 10.0.0.1 10.53.127.204 100 192.168.214.0 255.255.255.0 10.0.0.1 10.53.127.204 100 192.168.215.0 255.255.255.0 10.0.0.1 10.53.127.204 100 194.247.133.19 255,255,255,255 10.0.0.1 10.53.127.204 100 213,247,231,194 255,255,255,255 10.229.227.78 10.229.227.77 100 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.229.227.77 296 224.0.0.0 240.0.0.0 On-link 10.53.127.204 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.229.227.77 296 255.255.255.255 255.255.255.255 On-link 10.53.127.204 286 ================================================== ========================= Persistent Routes: None IPv6 Route Table ================================================== ========================= Active Routes: If Metric Network Destination Gateway 16 58:: / 0 On-link 1306:: 1 / 128 On-link 16 58 2001:: / 32 On-link 16 306 2001: 0:4137:9 e76: ea: b77: f51a: 1cb2/128 On-link 16 306 fe80:: / 64 On-link 26 286 fe80:: / 64 On-link 16 306 fe80:: ea: b77: f51a: 1cb2/128 On-link 26 286 fe80:: c073: 41b2: 852f: eb87/128 On-link 1306 ff00:: / 8 On-link 16 306 ff00:: / 8 On-link 26 286 ff00:: / 8 On-link ================================================== ========================= Persistent Routes: None C: \ Users \ Oleg>

  Read the article

• XEROX Phaser 3160N installation on UBUNTU 12.04 LTE machine

  - by Greg Verrall

  I have recently had windows XP die on one of my machines, and have installed Linux UBUNTU. The OS works great, except for installing the Xerox Phaser 3160N printer. The OS can find and install the network printer, but when I print a test page, it tells me “Internal Error – Please use the correct driver”. I have the correct drivers, as your support team have sent me the link, (http://www.support.xerox.com/support/phaser-3160/file-download/enau.html?operatingSystem=linux&fileLanguage=en_GB&contentId=105724&from=downloads&viewArchived=false) but I cannot install these drivers to run the printer. These are the instructions from the online guide for installing on a Linux machine: 1. Make sure that the machine is connected to your network and powered on. Also, your machine’s IP address should have been set. 2. Insert the supplied software CD into your CD-ROM drive. 3. Double-click CD-ROM icon that appears on your Linux desktop. 4. Double-click the Linux folder. 5. Double-click the install.sh icon. 6. The Xerox Installer window opens. Click Continue. 7. The Add printer wizard window opens. Click Next. 8. Select Network printer and click Search button. 9. The Printer’s IP address and model name appears on list field. 10. Select your machine and click Next. I get as far as step 5, and step 6 never happens, if it did, it would be very easy from there. There are options to add additional software to UBUNTU, however it does not recognise the installation CD as valid when I try to add it as a source. Any ideas on who can help me? regards, Greg Verrall

  Read the article

• How to make Connect Communications VPN connection in 10.10?

  - by Bilal Mohammad Qazi

  these steps were send by my iSP admin for ver10.10 and i'm using 11.10... step 1 sucessfully implemented till point 7 after that the problems are marked after '//' Step 2 i cannot completely do the step 2 How to make Connect Communications VPN connection in Ubuntu 10.10. 1st Step:- 1- Go to System > Administration > Synaptic Package Manage 2- Search for “PPTP”, check “network-manager-PPTP” and click “Apply” 3- Click on the Network Manager tray icon with your right mouse button and choose “Edit Connections…”. 4- Go to the “VPN” tab and click “Add”. 5- Choose “Point-to-Point Tunneling Protocol (PPTP)” as the VPN Connection Type 6- Check the VPN Connection Type and click “Create”. 7- Give your VPN connection a name and assign all the necessary information • Gateway = blue.connect.net.pk if you got Blue Package or • Gateway = green.connect.net.pk if you got Green Package or • Gateway = blueplus.connect.net.pk if you got BluePlus Package or • Gateway = red.connect.net.pk if you got Red Package • User name = Connect Communications Userid • Password = Connect Communications Password 8- Now Click on “Advanced” Authentication • Unchecked “PAP" // cannot uncheck • Unchecked “MSCHAP" // cannot uncheck • Unchecked “CHAP" • Checked only “MSCHAPv2" EAP shown in ver11.10 and cannot be unchecked Security And Compression. • Unchecked “Use Point-to-Point encryption (MPPE)”. • Unchecked “Allow statefull encryption”. • Unchecked “Allow BSD data Compression”. • Unchecked “Allow Deflate data Compression”. • Unchecked “Use TCP Header Compression”. • Unchecked “Send PPP echo Packets” Then Press “OK” then “Apply”. 9-Now you are able to connect to the specified VPN connection via the Networking Manager Then you can connect to VPN in the menu bar and your Internet icon will have a lock when the connection is successful. 2nd Step:- Open Terminal window. First, you open a terminal (Applications > Accessories > Terminal): Run command “sudo” Now gave root Password. Then run command “netstat -r -n” It will show some lines and for example from the last line pick the IP from 2nd column like 10.111.0.1 0.0.0.0 10.111.0.1 0.0.0.0 UG 0 0 0 eth0 Now run the fallowing command. echo “route add -net 10.101.8.0 netmask 255.255.252.0 gw 10.152.24.1” > /etc/rc.local note :- 10.111.0.1 is an example IP now run “ sh /etc/rc.local “

  Read the article

• DHCPv6: Provide IPv6 information in your local network

  Even though IPv6 might not be that important within your local network it might be good to get yourself into shape, and be able to provide some details of your infrastructure automatically to your network clients. This is the second article in a series on IPv6 configuration: Configure IPv6 on your Linux system DHCPv6: Provide IPv6 information in your local network Enabling DNS for IPv6 infrastructure Accessing your web server via IPv6 Piece of advice: This is based on my findings on the internet while reading other people's helpful articles and going through a couple of man-pages on my local system. IPv6 addresses for everyone (in your network) Okay, after setting up the configuration of your local system, it might be interesting to enable all your machines in your network to use IPv6. There are two options to solve this kind of requirement... Either you're busy like a bee and you go around to configure each and every system manually, or you're more the lazy and effective type of network administrator and you prefer to work with Dynamic Host Configuration Protocol (DHCP). Obviously, I'm of the second type. Enabling dynamic IPv6 address assignments can be done with a new or an existing instance of a DHCPd. In case of Ubuntu-based installation this might be isc-dhcp-server. The isc-dhcp-server allows address pooling for IP and IPv6 within the same package, you just have to run to independent daemons for each protocol version. First, check whether isc-dhcp-server is already installed and maybe running your machine like so: $ service isc-dhcp-server6 status In case, that the service is unknown, you have to install it like so: $ sudo apt-get install isc-dhcp-server Please bear in mind that there is no designated installation package for IPv6. Okay, next you have to create a separate configuration file for IPv6 address pooling and network parameters called /etc/dhcp/dhcpd6.conf. This file is not automatically provided by the package, compared to IPv4. Again, use your favourite editor and put the following lines: $ sudo nano /etc/dhcp/dhcpd6.conf authoritative;default-lease-time 14400; max-lease-time 86400;log-facility local7;subnet6 2001:db8:bad:a55::/64 {    option dhcp6.name-servers 2001:4860:4860::8888, 2001:4860:4860::8844;    option dhcp6.domain-search "ios.mu";    range6 2001:db8:bad:a55::100 2001:db8:bad:a55::199;    range6 2001:db8:bad:a55::/64 temporary;} Next, save the file and start the daemon as a foreground process to see whether it is going to listen to requests or not, like so: $ sudo /usr/sbin/dhcpd -6 -d -cf /etc/dhcp/dhcpd6.conf eth0 The parameters are explained quickly as -6 we want to run as a DHCPv6 server, -d we are sending log messages to the standard error descriptor (so you should monitor your /var/log/syslog file, too), and we explicitely want to use our newly created configuration file (-cf). You might also use the command switch -t to test the configuration file prior to running the server. In my case, I ended up with a couple of complaints by the server, especially reporting that the necessary lease file wouldn't exist. So, ensure that the lease file for your IPv6 address assignments is present: $ sudo touch /var/lib/dhcp/dhcpd6.leases$ sudo chown dhcpd:dhcpd /var/lib/dhcp/dhcpd6.leases Now, you should be good to go. Stop your foreground process and try to run the DHCPv6 server as a service on your system: $ sudo service isc-dhcp-server6 startisc-dhcp-server6 start/running, process 15883 Check your log file /var/log/syslog for any kind of problems. Refer to the man-pages of isc-dhcp-server and you might check out Chapter 22.6 of Peter Bieringer's IPv6 Howto. The instructions regarding DHCPv6 on the Ubuntu Wiki are not as complete as expected and it might not be as helpful as this article or Peter's HOWTO. But see for yourself. Does the client get an IPv6 address? Running a DHCPv6 server on your local network surely comes in handy but it has to work properly. The following paragraphs describe briefly how to check the IPv6 configuration of your clients, Linux - ifconfig or ip command First, you have enable IPv6 on your Linux by specifying the necessary directives in the /etc/network/interfaces file, like so: $ sudo nano /etc/network/interfaces iface eth1 inet6 dhcp Note: Your network device might be eth0 - please don't just copy my configuration lines. Then, either restart your network subsystem, or enable the device manually using the dhclient command with IPv6 switch, like so: $ sudo dhclient -6 You would either use the ifconfig or (if installed) the ip command to check the configuration of your network device like so: $ sudo ifconfig eth1eth1      Link encap:Ethernet  HWaddr 00:1d:09:5d:8d:98            inet addr:192.168.160.147  Bcast:192.168.160.255  Mask:255.255.255.0          inet6 addr: 2001:db8:bad:a55::193/64 Scope:Global          inet6 addr: fe80::21d:9ff:fe5d:8d98/64 Scope:Link          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1 Looks good, the client has an IPv6 assignment. Now, let's see whether DNS information has been provided, too. $ less /etc/resolv.conf # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8)#     DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTENnameserver 2001:4860:4860::8888nameserver 2001:4860:4860::8844nameserver 192.168.1.2nameserver 127.0.1.1search ios.mu Nicely done. Windows - netsh Per description on TechNet the netsh is defined as following: "Netsh is a command-line scripting utility that allows you to, either locally or remotely, display or modify the network configuration of a computer that is currently running. Netsh also provides a scripting feature that allows you to run a group of commands in batch mode against a specified computer. Netsh can also save a configuration script in a text file for archival purposes or to help you configure other servers." And even though TechNet states that it applies to Windows Server (only), it is also available on Windows client operating systems, like Vista, Windows 7 and Windows 8. In order to get or even set information related to IPv6 protocol, we have to switch the netsh interface context prior to our queries. Open a command prompt in Windows and run the following statements: C:\Users\joki>netshnetsh>interface ipv6netsh interface ipv6>show interfaces Select the device index from the Idx column to get more details about the IPv6 address and DNS server information (here: I'm going to use my WiFi device with device index 11), like so: netsh interface ipv6>show address 11 Okay, address information has been provided. Now, let's check the details about DNS and resolving host names: netsh interface ipv6> show dnsservers 11 Okay, that looks good already. Our Windows client has a valid IPv6 address lease with lifetime information and details about the configured DNS servers. Talking about DNS server... Your clients should be able to connect to your network servers via IPv6 using hostnames instead of IPv6 addresses. Please read on about how to enable a local named with IPv6.

  Read the article

• The DOS DEBUG Environment

  - by MarkPearl

  Today I thought I would go back in time and have a look at the DEBUG command that has been available since the beginning of dawn in DOS, MS-DOS and Microsoft Windows. up to today I always knew it was there, but had no clue on how to use it so for those that are interested this might be a great geek party trick to pull out when you want the awe the younger generation and want to show them what “real” programming is about. But wait, you will have to do it relatively quickly as it seems like DEBUG was finally dumped from the Windows group in Windows 7. Not to worry, pull out that Windows XP box which will get you even more geek points and you can still poke DEBUG a bit. So, for those that are interested and want to find out a bit about the history of DEBUG read the wiki link here. That all put aside, lets get our hands dirty.. How to Start DEBUG in Windows Make sure your version of Windows supports DEBUG. Open up a console window Make a directory where you want to play with debug – in my instance I called it C221 Enter the directory and type Debug You will get a response with a – as illustrated in the image below…   The commands available in DEBUG There are several commands available in DEBUG. The most common ones are A (Assemble) R (Register) T (Trace) G (Go) D (Dump or Display) U (Unassemble) E (Enter) P (Proceed) N (Name) L (Load) W (Write) H (Hexadecimal) I (Input) O (Output) Q (Quit) I am not going to cover all these commands, but what I will do is go through a few of them briefly. A is for Assemble Command (to write code) The A command translates assembly language statements into machine code. It is quite useful for writing small assembly programs. Below I have written a very basic assembly program. The code typed out is as follows mov ax,0015 mov cx,0023 sub cx,ax mov [120],al mov cl,[120]A nop R is for Register (to jump to a point in memory) The r command turns out to be one of the most frequent commands you will use in DEBUG. It allows you to view the contents of registers and to change their values. It can be used with the following combinations… R – Displays the contents of all the registers R f – Displays the flags register R register_name – Displays the contents of a specific register All three methods are illustrated in the image above T is for Trace (To execute a program step by step) The t command allows us to execute the program step by step. Before we can trace the program we need to point back to the beginning of the program. We do this by typing in r ip, which moves us back to memory point 100. We then type trace which executes the first line of code (line 100) (As shown in the image below starting from the red arrow). You can see from the above image that the register AX now contains 0015 as per our instruction mov ax,0015 You can also see that the IP points to line 0103 which has the MOV CX,0023 command If we type t again it will now execute the second line of the program which moves 23 in the cx register. Again, we can see that the line of code was executed and that the CX register now holds the value of 23. What I would like to highlight now is the section underlined in red. These are the status flags. The ones we are going to look at now are 1st (NV), 4th (PL), 5th (NZ) & 8th (NC) NV means no overflow, the alternate would be OV PL means that the sign of the previous arithmetic operation was Plus, the alternate would be NG (Negative) NZ means that the results of the previous arithmetic operation operation was Not Zero, the alternate would be ZR NC means that No final Carry resulted from the previous arithmetic operation. CY means that there was a final Carry. We could now follow this process of entering the t command until the entire program is executed line by line. G is for Go (To execute a program up to a certain line number) So we have looked at executing a program line by line, which is fine if your program is minuscule BUT totally unpractical if we have any decent sized program. A quicker way to run some lines of code is to use the G command. The ‘g’ command executes a program up to a certain specified point. It can be used in connection with the the reset IP command. You would set your initial point and then run the G command with the line you want to end on. P is for Proceed (Similar to trace but slightly more streamlined) Another command similar to trace is the proceed command. All that the p command does is if it is called and it encounters a CALL, INT or LOOP command it terminates the program execution. In the example below I modified our example program to include an int 20 at the end of it as illustrated in the image below… Then when executing the code when I encountered the int 20 command I typed the P command and the program terminated normally (illustrated below). D is for Dump (or for those more polite Display) So, we have all these assembly lines of code, but if you have ever opened up an exe or com file in a text/hex editor, it looks nothing like assembly code. The D command is a way that we can see what our code looks like in memory (or in a hex editor). If we examined the image above, we can see that Debug is storing our assembly code with each instruction following immediately after the previous one. For instance in memory address 110 we have int and 111 we have 20. If we examine the dump of memory we can see at memory point 110 CD is stored and at memory point 111 20 is stored. U is for Unassemble (or Convert Machine code to Assembly Code) So up to now we have gone through a bunch of commands, but probably one of the most useful is the U command. Let’s say we don’t understand machine code so well and so instead we want to see it in its equivalent assembly code. We can type the U command followed by the start memory point, followed by the end memory point and it will show us the assembly code equivalent of the machine code. E is for a bunch of things… The E command can be used for a bunch of things… One example is to enter data or machine code instructions directly into memory. It can also be used to display the contents of memory locations. I am not going to worry to much about it in this post. N / L / W is for Name, Load & Write So we have written out assembly code in debug, and now we want to save it to disk, or write it as a com file or load it. This is where the N, L & W command come in handy. The n command is used to give a name to the executable program file and is pretty simple to use. The w command is a bit trickier. It saves to disk all the memory between point bx and point cx so you need to specify the bx memory address and the cx memory address for it to write your code. Let’s look at an example illustrated below. You do this by calling the r command followed by the either bx or cx. We can then go to the directory where we were working and will see the new file with the name we specified. The L command is relatively simple. You would first specify the name of the file you would like to load using the N command, and then call the L command. Q is for Quit The last command that I am going to write about in this post is the Q command. Simply put, calling the Q command exits DEBUG. Commands we did not Cover Out of the standard DEBUG commands we covered A, T, G, D, U, E, P, R, N, L & W. The ones we did not cover were H, I & O – I might make mention of these in a later post, but for the basics they are not really needed. Some Useful Resources Please note this post is based on the COS2213 handouts for UNISA A Guide to DEBUG - http://mirror.href.com/thestarman/asm/debug/debug.htm#NT

  Read the article

• What is the best Apache logs Analyzer?

  - by Evgeny

  What real-time log analyzer can you suggest for Apache access and error logs? There is a list of web analytics software on wikipedia, but it would be great to hear opinions from people with experience without having to try all of them. Please don't suggest Google Analytics or any other hosted/javascript analytics suites, already using them, GA is not real-time and it is missing some data that the logs show. For example 404 errors, script errors, the full query-string of the referral, IP addresses, visitor path through the website, etc ...

  Read the article

• Why does my MySQL remote-connection fail (VLAN)?

  - by Johannes Nielsen

  ubuntu-community! Again I have a problem with my special friend MySQL :D I have got two servers - a database-server and a web-server - who are connected via VLAN. Now I want the web-server to have remote access to the database-server's MySQL. So I created the user user in mysql.user. user's Host is xxx.yyy.zzz.9 which is the internal IP-address of the web-server. xxx.yyy.zzz.0 is the network. I also created user with Host % . As long as I use MySQL on the database-server logging in as user, everything works fine. But trying to log in as user from xxx.yyy.zzz.9 using mysql -h xxx.yyy.zzz.8 -u user -p (where xxx.yyy.zzz.8 is the database-server's internal IP), I get ERROR 2003 (HY000): Can't connect to MySQL server on 'xxx.yyy.zzz.8' (110) So I tried to activate Bind-Address in the my.cnf file. Well, if I use xxx.yyy.zzz.8, nothing changes. But if I try xxx.yyy.zzz.9 and try to restart MySQL, I get mysql stop/waiting start: Job failed to start I checked the log files and found - nothing. The database-server's MySQL doesn't even register, that the web-server tries to connect remotely. My idea is, that maybe I didn't configure the VLAN properley, even though I asked someone who actually knows such stuff and he told me, I did everything right. What I wrote into /etc/networking/interfaces is: #The VLAN auto eth1 iface eth1 inet static address xxx.yyy.zzz..8 netmask 255.255.255.0 network xxx.yyy.zzz.0 broadcast xxx.yyy.zzz.255 mtu 1500 ifconfig returns eth1 Link encap:Ethernet HWaddr xxxxxxxxxxxxxx inet addr:xxx.yyy.zzz.8 Bcast:xxx.yyy.zzz.255 Mask:255.255.255.0 inet6 addr: xxxxxxxxxxxxxxx/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:241146 errors:0 dropped:0 overruns:0 frame:0 TX packets:9765 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:17825995 (17.8 MB) TX bytes:566602 (566.6 KB) Memory:fb900000-fb920000 for the eth1, what is, what I configured. (This is for the database-server, the web-server looks similar). ethtool eth1 returns: Settings for eth1: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 100Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: on MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00000003 (3) drv probe Link detected: yes (This is for the database-server, the web-server looks similar). Actually I think, everything is right, but it still doesn't work. Is there someone with an idea? EDIT: I commented ou Bind-Address in my.cnf after it didn't work.

  Read the article

• unable to read/write CIFS mounts in Ubuntu 11.10

  - by Paul Collins

  upgraded my laptop from 11.04 too 11.10 and since then the CIFS mounts are not working before the upgrade it would allow mounts on host names, in 11.10 its only IP addresses (not much of an issue) however all the shares i mount are as Read only despite the FStab File declaring the options rw and auto, i have chowned the mount point to be nogroup.nouser and it still wont work, here is an extract from my FSTAB: //192.168.1.1/stories /home/paul/Documents/Stories cifs rw,user,exec,auto,username=,password= 0 0

  Read the article

• Installing IIS 8 on Windows 8

  - by The Official Microsoft IIS Site

  In case you haven’t heard Windows 8 is now available. As a web developer I think one of the best reasons to upgrade to Windows 8 is that you can start testing IIS 8 right from your PC. This way if you don’t have a budget for a new server you can start to familiarize yourself with some of the new features. IIS 8 has some great new features such as Dynamic IP Restrictions an Application Initialization . However one of the best new features of IIS 8 enables you to throttle the CPU utilization for any...(read more)

  Read the article

• XConnect to Offer Free Trial of HD Voice Peering Federation

  First HD federation will provide scalable, end-to-end IP interconnection, using ENUM technology, to enable cross-network high-definition voice traffic between disparate networks.

  Read the article

• CodePlex Daily Summary for Monday, May 17, 2010

  CodePlex Daily Summary for Monday, May 17, 2010New Projects.NET Essentials Course: .NET Essentials course @ Telerik Academy Training project for the studentsAU/NZ Office 2010 Launch Demos: The AU/NZ Office 2010 Launch Demos are a collection of code samples that were used as part of the Office/SharePoint 2010 launch parties in Australi...CybennyCMS: Very simple CMS system for building sites with ASP.NET with templates for lay-out, content pages with only html content and a xml file for the site...essionPIM: essionPIMGIStance: A library for finding "nearest neighbor" among an in-memory set of positions, in C# and F#. A radius must be specified for making a meaningful s...IP Informer: IP Informer is IP Informer.Kurumsal Ofis Paketi: Kurumsal Ofis Paketi (KOP), Microsoft Ofis 2010 ürünleri için geliştirilmiş eklenti yazılımıdır. KOP, Word ve Excel’de bulunan işlevlerinin genişle...Mockup to XAML: Convert Balsamiq Mockups to XAML. This project supports BMML mockup control conversion using plugins. A standard set of controls are included wit...Open XML Validator: This WPF app give you a brief resume about errors in your Open XML documents.Paint.NET Bulk Image Processor: PDNBulkUpdater is a plug-in for Paint.NET that allows you to efficiently perform operations such as resizing and converting multiple images at the ...PiPiBugNet: PiPiBugNet是一套全新的开源Bug管理系统Roleplay character generator: The roleplay character generator allows the creation of characters for different roleplaying gamesSharePoint User Search WebParts: This project contains SharePoint webparts which provide advanced search configuration and experience for SharePoint 2007. It will be upgrade in few...Spodi: Spodi is created on 22-04-2010TfsPolicyPack: This project will provide a few checkin policies for VS 2010.vccodesandobx: vccodesandobxvccodesandobxvccodesandobxWhiteNile: test project using codeplexNew ReleasesAnimeStore.Net: 1.0.3.0: Build 1.0.3.0 Changes Move some functionality to features (MEF) Filter / Search functionality. Anime hard-copy records storage (e.g Disk Storage ...AU/NZ Office 2010 Launch Demos: Twitter map web part: This is the main twitter map web part download, see the Twitter Map web part page for all the information.Blueset Studio Opensource Projects: 推来: 稳定版本BUtil: BUtil 5.0 Alpha2: The initial implementation of multitasking (except ghost)CassiniDev - Cassini 3.5/4.0 Developers Edition: CassiniDev 3.5.1 and 4.0.1 beta: Beta 2 is released here: url http://cassinidev.codeplex.com/releases/view/45456 New in CassiniDev v3.5.1.0/v4.0.1.0 Added .Net 4 / VS10 build. ...CBM-Command: 2010-05-16: Release Notes - 2010-05-16New Features New navigation options: Page Up, Page Down, Top of Directory, Bottom of Directory. See documentation (http:...CCNet Conditional Plugin: CCNet Conditional for CCNet 1.5: A (quick) build of the plugin for CCNet 1.5 to fix the 17365 bug reported by Beakster. This also adds a new condition "timeCondition"CybennyCMS: Cybenny CMS beta 1: The first beta. Includes a small demo site.Data Extracting SDK: Data Extracting SDK v.1.1 RTM: RTM version of Data Extracting SDK.Duckworth Lewis Professional Edition Calculator: DLcalc 2.0: This software can perform all D/L calculations 100% accurately. From version 2.0 onwards, tables for par scores can also be produced.EPiServer CMS Page Type Builder: Page Type Builder 1.2: Release notes can be found in this blog post.Floe IRC Client: Floe IRC Client 2010-05 R5: - Many new context menu options for @s - Ability to select multiple users in the nick list for some operations (kick, ban) - Bunch of minor bug fix...Graffiti CMS Events Plugin: Version 1.0.1: Minor update to previous version to fix bug where deleted posts were still showing in the calendar.Microsoft Research Boogie: 2010-05-16: Binary release of Boogie and Dafny. (Note, Chalice is not pre-built as part of this binary release. To obtain it, you need to build it yourself f...MSBuild Launch Pad (mPad): 1.0 Beta 2: Basic support for sln, csproj, vbproj, vcxproj, shfbproj, ccproj, oxygene and proj files are added. Basic settings (Show Prompt, and Auto Hide) are...Multi-Language Words Memorizer: Memorizer 1.1: Issues fix, XML db update with new words.NShader - HLSL - GLSL - CG - Shader Syntax Highlighter AddIn for Visual Studio: NShader 1.1: New release of NShader! New : - a Visual Studio 2010 port can be installed through the new extension manager : you just have to download NShaderV...PHPExcel: PHPExcel 1.7.3 Production: Want to contribute?Please refer the Contribute page. DonationsDonate via PayPal. If you want to, we can also add your name / company on our Donati...Rollback - A social backup tool.: Rollback Setup 0.5.1.2 Build 48360: Bug fixes for backing up files which are hidden/system. Changes to make builds on 64 bit Windows 7 using VS 2010 Express edition.Rollback - A social backup tool.: Rollback Setup 0.5.1.3: Updated version number.Shake - C# Make: Shake v0.1.20: New: Simple console logger Changes: Command line params helper writes out syntax and samples (like msbuild) Fixes: Assembly info, file task and r...SharePoint User Search WebParts: v0.1 Friendly MOSS 2007 Search WebPart: Very first version of this webpart. A more stabilized version will follow in few days.Team Deploy: Team Deploy 2010 Beta 1: This is the initial release for Team Deploy 2010 for TFS Team Build 2010. All features from Team Build 2.x are functional in this version. Comp...Team Foundation Server Administration Tool: 2.0: TFS Administration Tool 2.0 TFS Administration Tool 2.0 is built on top of the Team Foundation Server 2008 object model and in order to connect to...The Ping Master: v0.9.0.0: Installer for The Ping Master binariesUseful Office Macros: All Macro Downloads: Please find above the downloads related to this project. Each Excel Workbook below works independently of the others, so you only need to download...VCC: Latest build, v2.1.30516.0: Automatic drop of latest buildVisual Studio DSite: Advanced Digital Board Game (Visual C++ 2008): An advanced digital board game made in visual c 2008.YUI Compressor Custom Tool for Visual Studio: YUI Compressor Custom Tool Full Version: Version 1.0 The following changes have been made: Merged classes to automatically sense if the target file is Javascript or CSS. Cleaned up setu...Most Popular ProjectsRawrWBFS ManagerAJAX Control ToolkitMicrosoft SQL Server Product Samples: DatabaseSilverlight ToolkitWindows Presentation Foundation (WPF)patterns & practices – Enterprise LibraryMicrosoft SQL Server Community & SamplesPHPExcelASP.NETMost Active Projectspatterns & practices – Enterprise LibraryPHPExcelBlogEngine.NETRawrMicrosoft Biology FoundationCustomer Portal Accelerator for Microsoft Dynamics CRMWindows Azure Command-line Tools for PHP DevelopersDotNetZip LibraryCaliburn: An Application Framework for WPF and SilverlightSQL Server PowerShell Extensions

  Read the article

• Amazon EC2 SIP Brute Force Attacks on Rise

  <b>VoIP Tech Chat:</b> "Complaints of rampant SIP Brute Force Attacks coming from servers with Amazon EC2 IP Addresses cause many admins to simply drop all Amazon EC2 traffic."

  Read the article

• Best development architecture for a small team of programmers ( WAMP Stack )

  - by Tio

  Hi all.. I'm in the first month of work in a new company.. and after I met the two programmer's and asked how things are organized in terms of projects inside the company, they simply shrug their shoulders, and said that nothing is organized.. I think my jaw hit the ground that same time.. ( I know some, of you think I should quit, but I'm on a privileged position, I'm the most experienced there, so there's room for me to grow inside the company, and I'm taking the high road ).. So I talked to the IT guy, and one of the programmers, and maybe this week I'm going to get a server all to myself to start organizing things. I've used various architectures in my previous work experiences, on one I was developing in a server on the network ( no source control of course ).. another experience I had was developing in my local computer, with no server on the network, just source control. And at home, I have a mix of the two, everything I code is on a server on the network, and I have those folders under source control, and I also have a no-ip account configured on that server so I can access it everywhere and I can show the clients anything. For me I think this last solution ( the one I have at home ) is the best: Network server with WAMP stack. The server as a public IP so we can access it by domain name. And use subdomains for each project. Everybody works directly on the network server. I think the problem arises, when two or more people want to work on the same project, in this case the only way to do this is by using source control and local repositories, this is great, but I think this turns development a lot more complicated. In the example I gave, to make a change to the code, I would simply need to open the file in my favorite editor, make the change, alter the database, check in the changes into source control and presto all done. Using local repositories, I would have to get the latest version, run the scripts on the local database to update it, alter the file, alter the database, check in the changes to the network server, update the database on the network server, see if everything is running well on the network server, and presto all done, to me this seems overcomplicated for a change on a simple php page. I could share the database for the local development and for the network server, that sure would help. Maybe the best way to do this is just simply: Network server with WAMP stack ( test server so to speak ), public server accessible trough the web. LAMP stack on every developer computer ( minus the database ) We develop locally, test, then check in the changes into the server test and presto. What do you think? Maybe I should start doing this at home.. Thanks and best regards... Edit: I'm sorry I made a mistake and switched WAMP with LAMP, sorry about that..

  Read the article

• Microsoft Fights Back Against Zeus Malware Ring

  According to a press release from Microsoft, the software giant, along with its partners, solicited the help of the U.S. Marshals on March 23 to seize Zeus command-and-control servers in charge of delivering malware updates, issuing commands, and stealing data in Lombard, Illinois, and Scranton, Pennsylvania. The active servers were seized on the premises of the two hosting companies before their owners could attempt to destroy the evidence. Microsoft was allowed to overtake 800 domains used by the Zeus servers and two IP addresses used to advance the operation were also dismantled. Microso...

  Read the article

• Understanding IIS Bindings

  - by OWScott

  Internet Information Services (IIS) uses 4 decision points for the site bindings.  They are the protocol, port, IP and host header.  This video lesson walks through the bindings and shows how each one is used. This is part 5 of a 52 week series on various topics for the Web Administrator. Other weeks include: Week 1 – Ping and Tracert Week 2 – Understanding DNS zone records Week 3 – Nslookup – the Ultimate DNS Troubleshooting Tool Week 4 – Three Tricks for Capturing Command Line Output Understanding IIS Bindings

  Read the article

• DHCP server with multiple interfaces on ubuntu, destroys default gateway

  - by Henrik Alstad

  I use Ubuntu, and I have many interfaces. eth0, which is my internet connection, and it gets its info from a DHCP-server totally outisde of my control. I then have eth1,eth2,eth3 and eth4 which I have created a DHCP-server for.(ISC DHCP-Server) It seems to work, and I even get an IP-address from the foreign DHCP-server on the internet facing interface. However, for some reason it seems my gateway for eth0 became screwed after I installed my local DHCP-server for eth1-eth4. (I think so because I got an IP for eth0, and I can ping other stuff on the local network, but I cannot get access to the internet). My eth0-specific info in /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp auto eth1 iface eth1 inet static address 10.0.1.1 netmask 255.255.255.0 network 10.0.1.0 broadcast 10.0.1.255 gateway 10.0.1.1 mtu 8192 auto eth2 iface eth2 inet static address 10.0.2.1 netmask 255.255.255.0 network 10.0.2.0 broadcast 10.0.2.255 gateway 10.0.2.1 mtu 8192 My /etc/default/isc-dhcp-server: INTERFACES="eth1 eth2 eth3 eth4" So why does my local DHCP-server fuck up the gateway for eth0, when I tell it not to listen to eth0? Anyone see the problem or what I can do to fix it? The problem seems indeed to be the gateways. "netstat -nr" gives: 0.0.0.0 --- 10.X.X.X ---- 0.0.0.0 --- UG 0 0 0 eth3 It should have been 0.0.0.0 129.2XX.X.X 0.0.0.0 UG 0 0 0 eth0 So for some reason, my local DHCP-server overrides the gateway I get from the network DHCP. Edit: dhcp.conf looks like this(I included info only for eth1 subnet): ddns-update-style none; not authoritative; subnet 10.0.1.0 netmask 255.255.255.0 { interface eth1; option domain-name "example.org"; option domain-name-servers ns1.example.org, ns2.example.org; default-lease-time 600; max-lease-time 7200; range 10.0.1.10 10.0.1.100; host camera1_1 { hardware ethernet 00:30:53:11:24:6E; fixed-address 10.0.1.10; } host camera2_1 { hardware ethernet 00:30:53:10:16:70; fixed-address 10.0.1.11; } } Also, it seems that the gateway is correctly set if I run "/etc/init.d/networking restart" in a terminal, but that's not helpful for me, I need the correct gateway to be set during startup, and i'd rather find the source of the problem

  Read the article

• w WARN: Thread pool pressure. Using current thread for a work item.

  - by GrumpyOldDBA

  The skill set needed by a DBA can be quite diverse at times and a run in with SSRS 2005 probably illustrates the point quite well. I don't have skills in IIS although I was responsible for the design and deployment of an online mortage application site some years ago.I had to get hands on with IIS5, firewalls, intrusion systems, ISA Server, dmzs, NAT, IP and lots of other acronyms so I have an understanding of these things but never had to do anything other than set up and configure IIS - no...(read more)

  Read the article

• As a programmer, should I know low and high-level programming languages?

  - by job

  I been contacted to do some work remote controlling LEDs displays over TCP/IP, but my experience and preparation is mostly about high-level programming language. I said that to the person who contact me about the work and he told me that: "if you call yourself a programmer you should know all these things" Should a programmer really know the details of low-level programming? Or can I treat it as a black box concept, as theoretical knowledge but not necessarily doing it or implementing low level language solutions, having in mind that low-level programming is not my expertise?

  Read the article

• rkhunter 1.4 different results than version before?

  - by dschinn1001

  with rkhunter version before ubuntu-update from 12.04 to 12.10 I had NOT these warnings like listed here: Performing file properties checks Checking for prerequisites [ Warning ] /usr/sbin/adduser [ Warning ] /usr/sbin/chroot [ Warning ] /usr/sbin/cron [ Warning ] /usr/sbin/groupadd [ Warning ] /usr/sbin/groupdel [ Warning ] /usr/sbin/groupmod [ Warning ] /usr/sbin/grpck [ Warning ] /usr/sbin/nologin [ Warning ] /usr/sbin/pwck [ Warning ] /usr/sbin/rsyslogd [ Warning ] /usr/sbin/tcpd [ Warning ] /usr/sbin/useradd [ Warning ] /usr/sbin/userdel [ Warning ] /usr/sbin/usermod [ Warning ] /usr/sbin/vipw [ Warning ] /usr/bin/awk [ Warning ] /usr/bin/basename [ Warning ] /usr/bin/chattr [ Warning ] /usr/bin/curl [ Warning ] /usr/bin/cut [ Warning ] /usr/bin/diff [ Warning ] /usr/bin/dirname [ Warning ] /usr/bin/dpkg [ Warning ] /usr/bin/dpkg-query [ Warning ] /usr/bin/du [ Warning ] /usr/bin/env [ Warning ] /usr/bin/file [ Warning ] /usr/bin/find [ Warning ] /usr/bin/GET [ Warning ] /usr/bin/groups [ Warning ] /usr/bin/head [ Warning ] /usr/bin/id [ Warning ] /usr/bin/killall [ Warning ] /usr/bin/last [ Warning ] /usr/bin/lastlog [ Warning ] /usr/bin/ldd [ Warning ] /usr/bin/less [ Warning ] /usr/bin/locate [ Warning ] /usr/bin/logger [ Warning ] /usr/bin/lsattr [ Warning ] /usr/bin/lsof [ Warning ] /usr/bin/lynx [ Warning ] /usr/bin/mail [ Warning ] /usr/bin/md5sum [ Warning ] /usr/bin/mlocate [ Warning ] /usr/bin/newgrp [ Warning ] /usr/bin/passwd [ Warning ] /usr/bin/perl [ Warning ] /usr/bin/pgrep [ Warning ] /usr/bin/pkill [ Warning ] /usr/bin/pstree [ Warning ] /usr/bin/rkhunter [ Warning ] /usr/bin/rpm [ Warning ] /usr/bin/runcon [ Warning ] /usr/bin/sha1sum [ Warning ] /usr/bin/sha224sum [ Warning ] /usr/bin/sha256sum [ Warning ] /usr/bin/sha384sum [ Warning ] /usr/bin/sha512sum [ Warning ] /usr/bin/size [ Warning ] /usr/bin/sort [ Warning ] /usr/bin/stat [ Warning ] /usr/bin/strace [ Warning ] /usr/bin/strings [ Warning ] /usr/bin/sudo [ Warning ] /usr/bin/tail [ Warning ] /usr/bin/test [ Warning ] /usr/bin/top [ Warning ] /usr/bin/touch [ Warning ] /usr/bin/tr [ Warning ] /usr/bin/uniq [ Warning ] /usr/bin/users [ Warning ] /usr/bin/vmstat [ Warning ] /usr/bin/w [ Warning ] /usr/bin/watch [ Warning ] /usr/bin/wc [ Warning ] /usr/bin/wget [ Warning ] /usr/bin/whatis [ Warning ] /usr/bin/whereis [ Warning ] /usr/bin/which [ Warning ] /usr/bin/who [ Warning ] /usr/bin/whoami [ Warning ] /usr/bin/unhide.rb [ Warning ] /usr/bin/gawk [ Warning ] /usr/bin/lwp-request [ Warning ] /usr/bin/heirloom-mailx [ Warning ] /usr/bin/w.procps [ Warning ] /sbin/depmod [ Warning ] /sbin/fsck [ Warning ] /sbin/ifconfig [ Warning ] /sbin/ifdown [ Warning ] /sbin/ifup [ Warning ] /sbin/init [ Warning ] /sbin/insmod [ Warning ] /sbin/ip [ Warning ] /sbin/lsmod [ Warning ] /sbin/modinfo [ Warning ] /sbin/modprobe [ Warning ] /sbin/rmmod [ Warning ] /sbin/route [ Warning ] /sbin/runlevel [ Warning ] /sbin/sulogin [ Warning ] /sbin/sysctl [ Warning ] /bin/bash [ Warning ] /bin/cat [ Warning ] /bin/chmod [ Warning ] /bin/chown [ Warning ] /bin/cp [ Warning ] /bin/date [ Warning ] /bin/df [ Warning ] /bin/dmesg [ Warning ] /bin/echo [ Warning ] /bin/ed [ Warning ] /bin/egrep [ Warning ] /bin/fgrep [ Warning ] /bin/fuser [ Warning ] /bin/grep [ Warning ] /bin/ip [ Warning ] /bin/kill [ Warning ] /bin/less [ Warning ] /bin/login [ Warning ] /bin/ls [ Warning ] /bin/lsmod [ Warning ] /bin/mktemp [ Warning ] /bin/more [ Warning ] /bin/mount [ Warning ] /bin/mv [ Warning ] /bin/netstat [ Warning ] /bin/ping [ Warning ] /bin/ps [ Warning ] /bin/pwd [ Warning ] /bin/readlink [ Warning ] /bin/sed [ Warning ] /bin/sh [ Warning ] /bin/su [ Warning ] /bin/touch [ Warning ] /bin/uname [ Warning ] /bin/which [ Warning ] /bin/dash [ Warning ] It seems that rkhunter 1.4 is oversensitive somehow about changed bin-files ? chkrootkit finds nothing and no warnings too.

  Read the article

• DRBD and MySQL - Heartbeat Setup

  Heartbeat automates all the moving parts and can work as well with the MySQL master-master active/passive solution as well as it can with the MySQL & DRBD solution. It manages the virtual IP address used by the database, directs DRBD to become primary, or relinquish primary duties, mounts the /dev/drbd0 device, and starts/stops MySQL as needed.

  Read the article

• DRBD and MySQL - Heartbeat Setup

  Heartbeat automates all the moving parts and can work as well with the MySQL master-master active/passive solution as well as it can with the MySQL & DRBD solution. It manages the virtual IP address used by the database, directs DRBD to become primary, or relinquish primary duties, mounts the /dev/drbd0 device, and starts/stops MySQL as needed.

  Read the article

• Avoid SEO loss after URL structure change

  - by Eric Nguyen

  We recently re-wrote our site from Umbraco to WordPress. This has been done by third-party developers. I have been the project manager and it is my mistake that I haven't notice the change of URLs that affect SEO until now. New site was launch last Thursday. The old URL for a "place" (a WordPress custom post type, in case you're WordPress expert and want/ need to point me to another discussion on WP Stackexchange) page is as follows: ourdomain.com/singapore/central/alexandra/an-interesting-place Now it has been changed to ourdomain.com/places/an-interesting-place I have already requested the third-party developers to work rewriting the URLs to emulate the old URL structure. However, it's taking quite a lot of time (we have multiple custom post types e.g. events etc. so it might be complicated; the developers seem quite by blur when I first mentioned rewriting URLs for the custom post types) In the meantime, I wonder if there is a quicker work around for this 1) Use .htaccess to rewrite ourdomain.com/singapore/central/alexandra/an-interesting-place to ourdomain.com/places/an-interesting-place This should avoid 90% loss of the search traffic. I suppose I can learn how to do this quite quickly but no harm mentioning it here 2) Use rel="canonical" to indicate that ourdomain.com/places/an-interesting-place is the exact duplicate of ourdomain.com/singapore/central/alexandra/an-interesting-place I will definitely go for both approaches (and also I'm changing 404 page to cater for this temporary isue) but I wonder if 2) is even feasible and if I have missed anything. Is there anything else you could recommend me in this situation. Let me know if my question is not clear anywhere. Clarifications The old website is on a Windows Server EC2 completely separated from the Linux EC2 instance on which the new site is running. In addition, the same domain "ourdomain.com" is used here (an A record is used to point to an EC2 Elastic IP). Therefore, the old server is completely inaccessible at the moment, unless you we use the IP address to old server (which doesn't help me at all in this case). Even if the old server is accessible, I can't see where one can put the .htaccess or a HTML file to do 301 redirect here. Unless I'm successful with my approach 1) or the developers can rewrite the URLs with coding, 404 page is really a choice for me.

  Read the article

• how can I disable ssh prompt from kvm remote

  - by kamil

  when I upgraded my KVM virtual machine manager to the latest version I got a question prompt every time I try to connect remotely to my machines: The authenticity of host 'kvm.local (ip address)' can't be established. ECDSA key fingerprint is b5:fa:0a:d0:39:af:0a:60:fa:04:87:6c:31:1d:13:15. Are you sure you want to continue connecting (yes/no)? And when changing any setting on a VM I was obliged to type yes and then type the root password in another dialog using ubuntu 12.04 64bit

  Read the article

• What are the basic features of an email module in a common web application?

  - by Coral Doe

  When developing an email module, what are the features to have in mind, besides actual email sending? I am talking about an email module that notifies users of events and periodically sends reports. The only other feature I have in mind is maintaining grey/black lists for users that do illegal operations in the system or any other things that may lead to email/domain/IP banning. Is there an etiquette for developing email modules? Are there some references of requirements for such modules?

  Read the article

• Using the fsc mount option with nfsroot kernel parameter to allow FS-cache

  - by meanderix

  I'm PXE-booting a Ubuntu 10.10 system, where I specify the kernel parameters as follows: append root=/dev/nfs initrd=ubuntu-boot/initrd.img-2.6.35-24-generic nfsroot=11.22.33.44:/data/nfsroot,fsc ip=dhcp rw I need to use the mount option 'fsc' in order to use FS-cache functionality (the cachefilesd package.) However, when I try this I get the following error upon boot: nfsmount: bad option 'fsc' Why doesn't nfsmount permit this option? (It works fine when you mount manually with "mount -o fsc" after booting up.)

  Read the article

< Previous Page | 213 214 215 216 217 218 219 220 221 222 223 224  | Next Page >