Search Results

Search found 11986 results on 480 pages for 'desktop'.

Page 219/480 | < Previous Page | 215 216 217 218 219 220 221 222 223 224 225 226  | Next Page >

• Linux Kernel Packet Forwarding Performance

  - by Bob Somers

  I've been using a Linux box as a router for some time now. Nothing too fancy, just enabling forwarding in the kernel, turning on masquerading, and setting up iptables to poke a few holes in the firewall. Recently a friend of mine pointed out a performance problem. Single TCP connections seem to experience very poor performance. You have to open multiple parallel TCP connections to get decent speed. For example, I have a 10 Mbit internet connection. When I download a file from a known-fast source using something like the DownThemAll! extension for Firefox (which opens multiple parallel TCP connections) I can get it to max out my downstream bandwidth at around 1 MB/s. However, when I download the same file using the built-in download manager in Firefox (uses only a single TCP connection) it starts fast and the speed tanks until it tops out around 100 KB/s to 350 KB/s. I've checked the internal network and it doesn't seem to have any problems. Everything goes through a 100 Mbit switch. I've also run iperf both internally (from the router to my desktop) and externally (from my desktop to a Linux box I own out on the net) and haven't seen any problems. It tops out around 1 MB/s like it should. Speedtest.net also reports 10 Mbits speeds. The load on the Linux machine is around 0.00, 0.00, 0.00 all the time, and it's got plenty of free RAM. It's an older laptop with a Pentium M 1.6 GHz processor and 1 GB of RAM. The internal network is connected to the built in Intel NIC and the cable modem is connected to a Netgear FA511 32-bit PCMCIA network card. I think the problem is with the packet forwarding in the router, but I honestly am not sure where the problem could be. Is there anything that would substantially slow down a single TCP stream?

  Read the article

• WHS - Windows Update Failure

  - by Kyle B.

  Clicking "Update Now..." inside my EX470 control panel for Windows Update produces the following error message: "Windows Home Server updates installation can not complete. Please try again later. If the problem persists, please restart the server." I have rebooted the server numerous times, and I have also used remote desktop to connect to the machine to perform the update this way, however the browser is unable to pull up http://windowsupdate.microsoft.com. This is very strange behavior because I am able to access all other sites (gmail.com, serverfault.com, etc). Would it be possible for someone to explain to me how I can check to see what is blocking the connection of this device, which apparently has a valid internet connection, to the Microsoft Windows Update site? note #1 Using the shortcut: %SystemRoot%\system32\wupdmgr.exe does not work either. It says "Connecting to 65.55.200.155..." but nothing ever happens. This is strange because all other sites seem fine. Also, I can connect to windowsupdate.microsoft.com on my local desktop so I know this is running as well

  Read the article

• How a batch file runs on a remote machine started by PSEXEC

  - by user38780

  I am having an issue running a Batch file on a remote machine suing PSEXEC. The file runs but does not run like it does when run through remote desktop. The batch runs a file which is a 32 bit application, which opens multiple 16bit applications, this should all run under one ntvdm.exe (In one Memory Space). Through remote desktop the batch file runs under the explorer process, and works correctly opening only one ntvdm.exe. Using PSEXEC the batch runs but not under the explorer process, a separate ntvdm.exe is open for each process. I found running the batch from explorer in PSEXEC works, but comes up with a "File Download - Security Warning" eg. psexec.exe" \compname -u username -p passowrd -s -d -i 0 explorer C:\Program.bat I want to be able to run the batch successfully without receiving warnings, it is a local warning and not a network share warning. Possible to recreate warning typing "explorer C:\windows\system32\cmd.exe" in Run I would like to know if anyone knows of a way to get PSEXEC to open the batch file to run as though it was started by explorer. Or a way of removing the local "File Download - Security Warning" Thanks

  Read the article

• How to bypass firewall to connect to a proxy server?

  - by Bruce

  I am conducting a small experiment on my office network. I have setup a proxy server on my desktop machine (connected to my LAN) and I have volunteers access the internet via my proxy server. Everything is working well. The problem is people cannot connect to the proxy server through their laptops. I asked my network admin and he said the wireless network has a firewall which prevents users from connecting to my proxy. He said I could tunnel the traffic or use SSH though. I am afraid I do not understand fully what is going on. Is there a way by which users connected on the wireless network can connect to my desktop? I am using FreeProxy on Windows as my proxy server: http://www.handcraftedsoftware.org/index.php?page=download FreeProxy allows me to create a SOCKS 4/4a/5 proxy. Is that what I need? Part of the experiment involves logging the URL requests of the users. I am doing a measurement study. So, any solution must allow me to log the URL requests of users. Also, what changes do I need to make in the browser configuration.

  Read the article

• Change DPI setting in Windows 8.1 for the Logon Screen

  - by jmc302005

  How can the DPI setting be changed for the Logon Screen in Windows 8.1? Microsoft has added per-user DPI settings. But this means that there is no adjustable DPI setting for the Lock/Logon screen. You can change the DPI setting to be the same across all displays and this does affect the icons and font on the lock/logon screen. However, it does not affect any app/program that can run on the lock/logon screen. Ex. I use a 44" flat screen TV for my monitor on my desktop. Big enough for me to sit in my recliner and use my computer. I use the on-screen keyboard most of the time. (I don't want to keep a keyboard next to me.) The problem is that with the new DPI setup the on-screen keyboard takes up nearly half the screen, which is too big. I tried looking through the registry to see if I could find a setting for it. In the key HKEY_USERS\.DEFAULT\Control Panel\Desktop there is a string value named LogicalDPIOverride with a value of -1. I have a feeling this is where I can fix the issue. I tried changing the value to 0 and to 1 with no change in the result. Instead I noticed that after logging out and back in the -1 value was back in the registry. How can I change this default DPI? Can I use the LogPixels string that worked for DPI in Windows 7? Here are two Screen shots, one of the Lock Screen and one of the Logon Screen:

  Read the article

• Ping: sendmsg: operation not permitted error after installing iptables on Arch GNU/Linux

  - by estol

  Yesterday I got a new computer as my homeserver, a HP Proliant Microserver. Installed Arch Linux on it, with kernel version 3.2.12. After installing iptables (1.4.12.2 - the current version afaik) and changing the net.ipv4.ip_forward key to 1, and enabling forwarding in the iptables configuration file (and rebooting), the system cannot use any of its network itnerfaces. Ping fails with Ping: sendmsg: operation not permitted If I remove iptables completely, networking is okay, but I need to share the Internet connection to the local network. eth0 - wan NIC integrated on the motherboard (no idea of vendor, probably HP). eth1 - lan NIC in a pci-express slot (Intel Gigabit CT Desktop http://www.intel.com/content/www/us/en/network-adapters/gigabit-network-adapters/gigabit-ct-desktop-adapter.html) Since it works without iptables(server can access the internet, and I can login with ssh from the internal network), I assume it has something to do with iptables. I do not have much experience with iptables, so I used these as reference (separate from each other of course...): wiki.archlinux.org/index.php/Simple_stateful_firewall#Setting_up_a_NAT_gateway revsys.com/writings/quicktips/nat.html howtoforge.com/nat_iptables On my previous server, I used the revsys guide to set up nat, worked like a charm. Anyone experienced anything like this before? What am I doing wrong? Thanks, estol

  Read the article

• How to use my computer as a Headset device for my phone with Bluetooth?

  - by TheJelly

  I want to extract the audio from my phone (the analog TV and FM/AM receiver mainly) and play it through my computer speakers. There is a headphone jack but it is of non-standard size (probably a micro-jack) and I do not have access to a shop that sells that kind of equipment in my area so doing this with Bluetooth is the only solution I can foresee. Both my laptop and my phone support A2DP but for some reason the service (from the phone) does not show up while I add a new connection and the phone does not let me initiate a connection with any other profile except FTP (although it detects other services in the service list like A2DP and works perfectly fine with other profiles like DUN, HID, OPP, SSP if the connection is started through the computer). I am currently using the latest version of the Toshiba stack, I have tried using WIDCOMM but it refuses to install drivers for both the internal Bluetooth (which is a Broadcom device) and the USB Bluetooth that I use on my desktop. The standard Microsoft stack (generic driver) does install but it does not work with both of my devices as they do not detect any Bluetooth devices when scanning. With BlueSoleil (the default stack that came with the USB Bluetooth) I could set my device as "headset" instead of only "laptop/desktop", and this allowed both my phones to detect my laptop as a device they can use as a headset, but the problem with this stack was that only the older phone could actually connect to my laptop and that the internal Bluetooth could not be used. Basically, I want to set the device type as a "headset" for my phone using the Toshiba stack like I did with BlueSoleil. Is there any way this could be done? Thanks. Image: Device type selection http://i.stack.imgur.com/drjC6.jpg

  Read the article

• Viewing a large-resolution VNC server through a small-resolution viewer in Ubuntu

  - by Madiyaan Damha

  I have two Ubuntu computers, one with a large screen resolution (1920x1600) that is running the default Ubuntu VNC server. I have another computer that has a resolution of about 1200x1024 that I use to VNC into the server using the default Ubuntu VNC viewer). Now everything works fine except there are annoying scrollbars in the viewer because the server's desktop resolution is so much higher than the viewer's. Is there a way to: Scale the server's desktop down to the viewer's resolution. I know there will be a loss of image quality, but I am willing to try it out. This should be something like how Windows Media Player or VLC scales down the window (and does some interpolation of pixels). Automatically shrink the resolution of the server to the client's when I connect and scale the resolution back when I disconnect. This seems like a less attractive solution. Any other solution that gurus out there use? I am sure someone has experienced this before (annoying scroll bars) so there must be a solution out there.

  Read the article

• update all the servers through one virtual servers using Storage are network virtual machine

  - by Mr.Calm

  Using UBUNTU and Virtal Box by Oracle, and Using this script to start nginx in Virtual Box, and placing it in Virtual box inside~/init.d #!/bin/bash ### BEGIN INIT INFO # Provides: Testinit # Required-Start: # Required-Stop: # Default-Start: 2 3 4 5 # Default-Stop: 0 1 6 # Short-Description: Start daemon at boot time # Description: Enable service provided by daemon. ### END INIT INFO # RETVAL=0; start() { CurrentTime=$(date +%d/%m/%Y"-"%I:%M:%S) ./usr/local/nginx/sbin/nginx echo "Current Time:"$CurrentTime>>/home/server/Desktop/NginxLogs.txt echo "!Starting nginx!" >>/home/server/Desktop/NginxLogs.txt Like this i want to write auto script (setup.sh file) and place that script in all virtual boxes inside my system, for example 8 virtual boxes and in all Virtual boxes NGINX is installed. Now, The thing is i am facing problem when i want change something in setup.sh i have to go to each and every virtual box, or Communicate each Virtual machine through SSH from my main machine. i am thinking to write another script (ex: Update.sh),and inside that script we give one path of file which is saved and recently edited in main machine (ex: DummySetup.sh). as soon as i run that script all the setup.sh files which are saved in each virtual machines should update the change or replace contents with DummySetup.sh's contents. Hope this is possible thing. Help would be appreciated.Thanking you

  Read the article

• How to monitor process hogging CPU on a remote server

  - by sergeb

  I have a remotely hosted (virtual, VMware) dedicated server (Windows 2008 Server Web edition w/ SP1) that I can only connect to over Remote Desktop. Lately, a process hogs CPU for ~40 minutes most every day (at a random hour) and brings all web sites on the server down. While this is going on I also cannot connect using Remote Desktop to investigate on what is that process... Promptly after 40 min I can RD and the first thing I see on the Perf Monitor is that there was something topping the CPU at 100% and stops just before I'm able to RD... I'm aware of the beginning and end of this for I have monitors setup that email me up/down status of the web sites but I'm locked out while this is happening - can't RD to the server until it's over (and too late to see the Task Manager/Process Explorer picture). What is the best way/tool to setup on the server to continuously monitor all processes so when this happens I login and "replay" it to find the process causing this trouble? (I have no control over the virtual/VMware setup for it is hosted by a 3rd-party but I have most full control over my dedicated machine) Thanks in advance!

  Read the article

• GNOME 2 + Compiz equivalent?

  - by virtualeyes

  Running Fedora 14 and realize I need to either change distros or find an alternative to GNOME 3 in Fedora 17. Based on what I have read to-date, XFCE and KDE are the go-to WMs if I want to avoid GNOME 3. I tried KDE 4 and I wasn't impressed; I like the simplicity of GNOME 2 with Compiz and Emerald. Can't stay on Fedora 14 forever, however, so...where to turn? Basically looking for these features in my desktop environment: GNOME Do or equivalent Snap to grid/Window tiling A must-have, the ability to hot key focused window to a monitor grid region is a huge productivity win. Zoom window to cursor In a multi-monitor setup sometimes it's nice to, say, GNOME Do terminal in one monitor and then hot key the opened window to the other monitor just by zipping the mouse cursor anywhere on target monitor (followed by, of course, snap-to-grid hotkey, all without a single mouse click) Polarization At night white background hurts the eyes, so I prefer to hot key polarize to black. Multi-monitor support I'm partial to Fedora given that I've worked with CentOS for years and have little experience with any other Linux distro; however, if the difference between Fedora and Arch, Mint, etc. is fairly subtle, I'll make the leap, just need a distro & desktop environment that allows me to be productive with keyboard hot keys and provides the above basic features. Any suggestions?

  Read the article

• Intel Rapid Storage Technology (pre-OS) driver installation

  - by Nero theZero

  My desktop machine is built on Gigabyte GA-Z87-UD3H and Gigabyte provides the latest driver for Intel Rapid Storage Technology (IRST), which I installed after installing the OS. Same goes for my Lenovo Thinkpad-T420. And for both machine, checking the controller device under the IDE ATA/ATAPI Controllers section in Device Manager I see the driver has been updated to the latest version. I set the SATA controller to AHCI from BIOS On the desktop machine I have one WD 2TB BLACK & one WD 3TB Green I don’t use RAID, & no chance of using in near future, but according to Intel IRST improves performance in single disk scenario too. Now I have the following questions – What is the actual purpose of IRST (pre-OS install) driver that doesn’t get served with a post-OS driver that I installed? There must be some difference, otherwise there wouldn’t be a pre-OS version of the driver. Right? In the pre-OS procedure (loading the drivers at OS-installation time) after successfully completing the OS installation, do I need that post-OS driver? Because after installing from that one I got a quick launch icon that runs the IRST configuration application. Where do get that after installing the pre-OS driver? As it is “pre-OS”, when I load it at OS-installation time, does it updates anything at BIOS level or anywhere other than HDD? That’s because I’m going to dual boot Windows 7 with Windows 8.1, and after installing Windows 7 when I install Windows 8.1 & load the IRST driver for that, is there any chance of any “overwriting” or OS-incompatibility? In short, is there anything specific to follow while installing the second OS?

  Read the article

• VMware ARP/Mac Networking

  - by Ross Wilson

  Hi Guys, I am very interested in how VMware networking works. I have scoured the VMware website and read their data sheets, this has given me some basic knowledge. I now have some questions. Lets assume that we have a physical server running the VMware hypervisor. The physical server is running a Virtual Machine. The physical box has one physical NIC. The NIC is connected to a switch, as so is a desktop client. Now, this is where my first question lies. The VM has an IP address: 192.168.1.1. How do desktop clients on the network communicate with this VM? So, the client pings 192.168.1.1. The ping packet is sent to the switch. The switch checks its MAC address table and sees that 192.168.1.1 is associated with the MAC address of the physical NIC. Correct? I then assume that the ping packet is sent to the server's physical NIC, where the hypervisor routes the packet to the VM thats using 192.168.1.1? Please could you give me a run down as to how VM networking works? Many thanks, Ross

  Read the article

• How to wake from screensaver directly to the login screen in Ubuntu

  - by torbengb

  (a.k.a. How to switch users without entering password, part II) (see part I) I've got Ubuntu 9.10 with a user account for my wife, and one for myself. "Wake-from-screensaver" should result in "choose user" without having to enter any password. I know how to do that in Windows, but I'm not good with Linux (yet). Part of this was answered in my earlier question which helped me get past the login screen without passwords (after booting, and after choosing "switch user"), but once the screensaver kicks in and I wake it up again, the system does not present the "choose user" screen. Instead, it either turns off the screensaver and presents the desktop of the most recent user, or (if the screensaver is set to lock the screen) prompt for the user's password (which can be handily surpassed by clicking the "switch user" button and choosing the same user again). So, the login ("choose user") screen has been dealt with. How do I make the (any) screensaver return to the login screen at wake, rather than to the current user's desktop? Windows can do this, I'm sure Linux can too - but how?

  Read the article

• My EliteBook is not auto picking 1080p for external monitor, poor display on forcing

  - by Griever

  I'm connecting my Samsung LED S22A300B to my HP EliteBook 6930p through VGA out. Laptop has Intel 4500MHD video card. I have latest drivers installed for both card and monitor. Only 800x600 and 1024x768 are shown. A lot of other people get this problem when they use it with docking station as discussed here. But I am not using any docking station. The monitor works great with my desktop though. As advised on the aforementioned page, one of the things I tried was to force the resolution using Intel's "custom resolution" feature. I installed PowerStrip on my desktop and copied advanced timing values(front/back porch,sync width, etc.) from there and then used the same values while defining a custom resolution in my laptop's Intel graphics utility. As a result, I got the 1080p resolution but the display is poor. Text has some weird colored shadow and sometimes on images too. What should I do?

  Read the article

• Samba and Windows 7

  - by John Gaughan

  I built a new computer with the intention of it being primarily a home file server. Here is my setup: one desktop with Windows 7 64 HP one laptop with Windows 7 64 HP one desktop with Kubuntu 11.10 (server) The two desktops use static IPs, and I have hostnames mapped in the HOSTS files on all three systems. I have the same username/password combo on all three systems. I have been trying for a while now to set up Samba so the Windows 7 systems can see and use it. Even if I can get the server to show up, Windows is unable to log in. One of the first things I did was to enable LMv2 authentication, which this version of Samba (3.5.11) supports. The workgroup is set correctly. I can normally see the server, but cannot authenticate. Windows homegroup is turned off. Pinging between machines works fine, and the two Windows 7 systems work together flawlessly. What I am trying to do is set up Samba to use peer to peer networking using NTLM security and user-mode authentication. According to the documentation this is possible, but there are no examples that I could find. In all the googling I have done, I see a lot of people asking how to set this up but it either works for someone else and not for me (no idea what I'm missing), or it doesn't work. Has anyone gotten this to work? Is there a place I could download a smb.conf that is set up to work in this environment?

  Read the article

• How to activate Win XP from Windows 7 compatibility mode on MacOS Parallels 5

  - by Ben Hammond

  I am running Parallels Desktop 5.0.9344 for Mac. I am running Mac OS 10.6.3 10D2094 I have bought a retail copy of Window 7 professional specifically because I need the XP compatibility. Windows 7 is installed and working. I have problems with the XP activation Windows7 'Virtual PC' does not run under Parallels (strange error about Server Execution failed 0x80080005). I have used the Parallels Transporter to convert the "Windows XP Mode Base.vhd" file into a parallels Virtual Machine. This copy of XP now starts normally, however it records itself as unregistered. There was a KEY.txt file in the same directory as the .vhd file; although this file contains a valid-looking activation key, it does not appear to activate the instance of XP. I have also tried to enter the Win7 activation key; this does not work either. I have tried calling the two phone numbers; an automated system asked me to enter 56 digits through the telephone and then accused me of being a pirate. I believe it may be possible to install Win7 via Bootcamp, start WinXP under Virtual PC, activate it and then import this activated .vhd into Parallels; but that seems a long way round, and is far from certain. What can I do to get WinXP running under Mac Parallels Desktop ?

  Read the article

• Win7 Aero disabled due to mirror drivers following TightVNC use, cannot re-enable

  - by me_and

  I recently installed TightVNC, and used it to access my desktop from my phone. When I did so, my desktop reported that Aero had been disabled due to an application being run that didn't support it. I now cannot re-enable Aero, despite having closed the TightVNC server (and indeed having rebooted a number of times since). Windows 7 troubleshooting reports the following: Close programs using mirror drivers To allow Aero effects to be displayed, close any programs that use mirror drivers (a type of display driver), such as Windows Remote Assistance and Windows Live Mesh. The troubleshooting system appears to attempt to automatically fix that, but fails. I can see nothing in the task manager that obviously uses mirror drivers; in particular, I can see nothing that looks like TightVNC in there. Starting and exiting TightVNC makes no difference. Google has turned up nothing that looks useful so far, either, although my Google-fu isn't great and I may just be searching for the wrong things. There's another question that reports the same problem, caused by LogMeIn rather than TightVNC, but the solution listed there doesn't work—TightVNC doesn't install LogMeIn mirror drivers, for obvious reasons.

  Read the article

• Unable to connect to shared (iscsitarget) dvd-rw drive on ubuntu karmic box

  - by develop7

  Preface: I have desktop with DVD-RW drive that runs primarily on Linux (namely Ubuntu 9.10). My wife has netbook that rins Windows XP with no cd/dvd drive. There's also LAN through our ADSL modem/router. I've "ported" (actually, I've just grabbed sources and ran dpkg-buildpackage) iscsitarget package from Ubuntu Lucid to Karmic (here are packages), installed it (sudo aptitude install iscsitarget; sudo m-a a-i iscsitarget) and configured it in the following way (/etc/ietd.conf): Target iqn.2020-01.local.develop7-desktop:storage.disc.dvdrw Lun 0 Path=/dev/sr0,Type=blockio #I've skipped commented lines Also, I've opened port 3260 with ufw: $ sudo ufw status | grep 3260 3260 ALLOW 192.168.1.0/24 But (here's the trouble) I still can't connect to this target from Windows box. Microsoft Software iSCSI Initiator tells "Logon failure" upon connect attempt. After unsuccessful connection attempt I've noticed this line in dmesg | tail's output: iscsi_trgt: ioctl(299) invalid ioctl cmd c078690d So the question is — what's wrong with my config/iSCSI target/whatever else? Or, in short — what I'm doing wrong? Thanks in advance.

  Read the article

• Unable to connect to shared (iscsitarget) dvd-rw drive on ubuntu karmic box

  - by Develop7

  Intro I have desktop with DVD-RW drive that runs primarily on Linux (namely Ubuntu 9.10). My wife has netbook that rins Windows XP with no cd/dvd drive. There's also LAN through our ADSL modem/router. I've "ported" (actually, I've just grabbed sources and ran dpkg-buildpackage) iscsitarget package from Ubuntu Lucid to Karmic (here are packages), installed it (sudo aptitude install iscsitarget; sudo m-a a-i iscsitarget) and configured it in the following way (/etc/ietd.conf): Target iqn.2020-01.local.develop7-desktop:storage.disc.dvdrw Lun 0 Path=/dev/sr0,Type=blockio #I've skipped commented lines Also, I've opened port 3260 with ufw: $ sudo ufw status | grep 3260 3260 ALLOW 192.168.1.0/24 Problem But (here's the trouble) I still can't connect to this target from Windows box. Microsoft Software iSCSI Initiator screams "Logon failure" upon connect attempt, and, respectively, fails to connect. After unsuccessful connection attempt I've noticed this line in dmesg | tail's output: iscsi_trgt: ioctl(299) invalid ioctl cmd c078690d Question So the question is — what's wrong with my config/iSCSI target/whatever else? Or, in short — what I'm doing wrong? Thanks in advance.

  Read the article

• Shared printer stops working on clients but not host computer

  - by Tony

  I have a Brother MFC-7420 USB all-in-one laser printer. It is plugin via USB to my Windows 7 x64 machine. I have it shared to a few users on my home network. My wife's laptop running Vista x64 can normally print fine to the printer. However it seems that every day or two, when she pushes print on a something it just sits in her laptop's print queue and never makes it to my desktop. The only thing that seems to fix this is if she restarts her laptop. Not a big deal but this problem is sort of annoying. I don't know if this affects but the laptop is put into hibernate at night and I turn my desktop off at night. Does anyone know why this happens and if there is something easy to do to fix the problem besides restart the computer? EDIT: I was thinking that maybe my wife's laptop loses its connection to the printer. Is there a way to reset a connection to a shared printer? Or maybe reauth with the printer?

  Read the article

• Domain joined computer unable to access servers through VPN

  - by kscott

  Our servers are in a virtual off site hosting center, our office has a vpn connection to the data center, but for reasons I don't understand we also have to connect to the Citrix Access Gateway (CAG) client in order to access the servers. I am a programmer with rather limited ops knowledge including a weak grasp of networking and terminology. Bear with me. I was just given a new laptop, which is a 64 bit Windows 7 system unlike my previous 32 bit Windows XP desktop which was able to connect without issue. My laptop has been joined to the domain so that I login with my AD credentials, I am able to connect to the CAG and get authenticated, and after doing this I can ping our servers and they resolve to the correct internal IP addresses, but I am unable to use remote desktop to the servers, connect to SQL servers through my local SQL Management Studio, navigate to them through the file system, or view any of our internal intranet websites. All of which I was able to do previously. I have tried turning off my Windows firewall and the problem remains, the DNS servers are set to the correct IPs of our domain controllers, and the ops guys here are a little stumped. Does any one have any suggestions?

  Read the article

• Computer causing WiFi interference?

  - by Mannimarco

  I came back from college and brought my desktop computer. Family recently switched to Verizon FIOS and got a new router because of it. Unfortunately, my connection to the new wifi network is awful, with the download speeds (tested through speedtest.net) fluctuating wildly and often dropping below 1.5 Mbps. A laptop in the same room gets 20 Mbps. I've tried a new wireless card, thinking that mine got damaged in the move home but no luck. Here's where it gets weird: if I place the laptop near the computer, the laptop's download speeds often suffer greatly. Pulling the laptop away always fixes this. So now I'm under the impression that there's something in the computer (which I built a year ago and has had 0 issues up to this point) is causing an insane amount of wireless interference. Also bizarre: the upload speeds seem unaffected by this problem. On the laptop and desktop, upload speeds are generally around 5 Mpbs. Any ideas as to what could be causing this and how to test said theories would be fantastic.

  Read the article

• GnuPG Command Line - Verifying KeePass Signature

  - by Stisfa

  I'm trying to verify the PGP Signature of the latest version of KeePass 2.14's setup file against this signature, but this is the output I receive: C:\Program Files (x86)\GNU\GnuPG>gpg.exe --verify C:\Users\User\Desktop\KeePass-2.14-Setup.exe gpg: no valid OpenPGP data found. gpg: the signature could not be verified. Please remember that the signature file (.sig or .asc) should be the first file given on the command line. C:\Program Files (x86)\GNU\GnuPG> I found this command here, but it made no mention about ".sig" or ".asc" files, so I figured I did something wrong. By reading (http://www.gnupg.org/documentation/manuals/gnupg/gpgv.html#gpgv), I further tried the following: C:\Program Files (x86)\GNU\GnuPG>gpg.exe --pgpfile C:\Users\User\Desktop\KeePass-2.14-Setup.exe gpg: Invalid option "--pgpfile" C:\Program Files (x86)\GNU\GnuPG> As you can see, the results are quite obfuscating... I took a look at this on SuperUser (http://superuser.com/questions/16160/short-easy-to-understand-explanation-of-gpg-pgp-for-nontechnical-people - I couldn't use "a href" due to the built in spam filter that discriminates against users with < 10 rep; this is the same reason for the link above this link), but none of the links seemed to really address my question, at least not directly enough for me to get any idea on how to move forward on this. Can anybody here help me with the esoteric technicality of OpenPGP & the associated use of the GnuPG program? I've felt pretty dumb learning VBS, but this is beyond humiliating: it's absolutely debilitating and maiming whatever confidence I had with my IT skills (then again, I have no justification for making any boast either, as I have yet to get my A+ Cert, lol).

  Read the article

• Bash script to run a clamscan on Ubuntu- how to use return values properly?

  - by Marius

  I'm trying to put together a simple script that will scan my home directory with clamscan and give me a warning if any viruses were found. What I have so far is: #! /usr/bin/env bash clamscan -l ~/.ClamScan/$(date +"%a%b%d") -ir /home RETVAL=$? [ $RETVAL -eq 0 ] && notify-send 'clamscan finished. No viruses found' [ $RETVAL -eq 1 ] && notify-send 'clamscan found a virus' && touch ~/Desktop/VirusFound [ $RETVAL -eq 2 ] && notify-send 'clamscan encountered errors. Check the logs' && touch ~/Desktop/ClamscanError find ~/.ClamScan/* -mtime +7 -exec rm {} \; However, I'm unsure about a couple of things: I'm always wary of using rm- as far as I can tell, the find command I've got should be deleting any log files that are more than a week old. I'm also not entirely sure how the return value testing works- I've got a manual that briefly covers bash, which says that the meaning of $? is "match one character", and I'm not entirely sure how that grabs the return value. Should I be using -eq or = for testing the return value? From what I can tell -eq tests strings and = tests numerals, but I'm not sure what the type of the return value is.

  Read the article

< Previous Page | 215 216 217 218 219 220 221 222 223 224 225 226  | Next Page >