Search Results

Search found 10688 results on 428 pages for 'dynamic pdf'.

Page 219/428 | < Previous Page | 215 216 217 218 219 220 221 222 223 224 225 226  | Next Page >

  • Windows Home Server 2011, No disks "suitable for a backup destination"

    - by Scott Beeson
    I recently installed Windows Home Server 2011 and love it. However, when I try to set up server backups, it says no suitable disks are available. Initially, before I set up my RAID, it found one of my twin drives and said it would work. Once I set up the mirroring, that one is no longer available (obviously). However, I have an internal SATA 1TB drive and an external USB2.0 1TB drive hooked up. Both are recognized by Disk Management. WHS11 still says nothing suitable for backups. The two drives details are as follows: Edit to clarify: The system partition is on Disk 0, not listed below. The two below are the two that SHOULD be available for system backups. Disk 1: Dynamic "Data" (D:) 931.51 GB NTFS, Healthy Disk 3: Basic 200 MB Healthy (EFI System Partition) "Backup" 930.66 GB NTFS, Healthy (Primary Partition) What's a bit odd is that in Disk Management the "Backup" volume does not show a drive letter, even though I assigned Z: (which is reflected in "My Computer". I also cannot make this a dynamic disk as it says it's unsupported by the device.

    Read the article

  • Setup shared internet connection on virtualbox with fixed IP

    - by Tom
    I am a web developer and until recently I have been using ubuntu as my OS. For many reasons, I have switched back to windows. I still want to keep my server on linux platform, so I setup my local server as a virtual machine. Everything works great, but i have a little struggle with the networking. Since I am working in different places and going around clients, I connect to all sorts of network with different settings. That means the possible IP range is very dynamic which causes issues when I work on my local server. At the moment I have a dynamic IP on my host and static IP on my guest. That way I can access the server from my host (by adding record to hosts file). I also have internet connection on the guest. But once i change networks, it does not work (assuming the network has different configuration). My question is, how to setup host-guest networking, so no matter what network I connect to, I can keep my static IP on guest, which is registered in hosts file on my host so I can access the webserver and also I will have internet connection on the guest? Hope it make sense. Thank you

    Read the article

  • Hyper-V and attaching physical disks [migrated]

    - by Mike Christiansen
    So, I'm looking at rebuilding my home server. My current setup is the following Windows 7 Ultimate 1TB Boot Drive (my smallest drive) Windows Dynamic Spanned volume, continaing 1x 1TB drive, 2x 2TB drives, totalling 5TB. I am upgrading to a hardware RAID controller, and I would like to run Hyper-V server core. However, I want to retain the ability to join my "file server" to a homegroup, so I must use Windows 7. I know VHDs can only be like 127GB or something, so I obviously need to directly connect disks to my Windows 7 machine. Here is my plan: Server Core 2008 R2 (Hyper-V) 1TB Boot Drive (storing VHDs for boot drives of VMs) - possibly in a RAID 1 with my other 1TB drive 5x 2TB drives (1x 2TB drive hot spare), totalling 10TB, directly attached to a Windows 7 VM, for use of homegroup for this array. In the past, I directly attached the windows dynamic volume to a Windows 7 VM, and performance was abysmal. The question is, with hardware RAID, will it really make that much of a difference? Server specs: Intel Core 2 Quad Q9550 2.83GHz Asus Maximus II Formula (PCI-E x16) 8GB DDR2 RAM PC2-6400 (Yes, I know its a bit out of date)

    Read the article

  • How can I read PDFs with e-reader on a Lenovo tablet?

    - by Jack M
    This is my first time using a tablet and I'm totally lost - this must be what computers look like to old people. This is a Lenovo Thinkpad tablet. I don't see a specific model number on it (it was passed down to me second hand). What I'd like to do is read a PDF. I'm fairly certain I successfully transferred the PDF onto the tablet via an SD card, and I noticed this thing has an app called "eReader" on it, so I started that up. All I see are empty bookshelves, and no obvious buttons or settings anywhere. I saw in multiple places that you have to, as one site puts it: ...copy and paste the relevant files into the eBooks folder and they will appear on the eReader shelf for your consumption... But I have no idea how to: Access the file system. Locate the eBooks folder. Copy and paste files. Will I need a file explorer app? If so, how can I install that given that my only method of getting data onto this tablet is an SD card (no wireless internet).

    Read the article

  • Cannot make bind9 forward DNS query to subdomain unless recursive enabled

    - by PP.
    I am trying to develop my own dynamic DNS. I'm running my own custom DNS for the subdomain on port 5353. ASCII diagram: INET --->:53 Bind 9 --->:5353 node.js | V zone_files I have example.com. The node.js DNS is for dyn.example.com. In my /etc/bind/named.conf.local I have: zone "example.com" { type master; file "/etc/bind/db.com.example"; allow-transfer { zonetxfrsafe; }; }; zone "dyn.example.com" IN { # DYNAMIC type forward; forwarders { 127.0.0.1 port 5353; }; forward only; }; I've even gone so far as to add a NS in my example.com zone file: $TTL 86400 @ IN SOA ns.example.com. hostmaster.example.com. ( 2013070104 ; Serial 7200 ; Refresh 1200 ; Retry 2419200 ; Expire 86400 ) ; Negative Cache TTL ; NS ns ; inet of our nameserver ns A 1.2.3.4 ; NS record for subdomain dyn NS ns When I attempt to get a record from the subdomain server it doesn't get forwarded: dig @127.0.0.1 test.dyn.example.com However if I turn recursive on in /etc/bind/named.conf.options: options { recursion yes; } .. then I CAN see the request going to the subdomain server. But I don't want recursion yes; in my Bind configuration as it is poor security practice (and allows all-and-sundry requests that are not related to my managed zones). How does one forward (proxy) zone queries for just one zone? Or do I give up on Bind altogether and find a DNS server that can actually forward specific queries?

    Read the article

  • How expensive is a hostname in htaccess? Other solutions possible?

    - by Nanne
    For easy allow or disallowing of dynamic IP-adresses you can add them as a hostname in a .htaccess file. As I have read from: .htaccess allow from hostname? it does a reverse lookup on the connecting ip address, seeing if the response matches the allowed name. (Well, actually Apache is doing a double lookup, first a reverse lookup and then a forward lookup on the result of the reverse.) This is the reason we are currently not using dynamic-ip hostnames in the .htaccess: this "sounds" quite heavy: 2 extra lookups for every request. Is this indeed quite heavy, and would a reasonably busy server that is rather looking for less then more load get away with this :)? (e.g.: how does this 'load' compare to the rest? If a request is 1000 times more expensive then the lookups it might be negligible. otoh, it could be that final straw :) ) Are there other solutions? I can write a script that does a lookup of the hostname and put it in .htaccess files ofcourse, but this feels a bit like a hack.

    Read the article

  • How can I diagnose what's causing Outlook 2007 when sending an attachment to fail with error 800CCC0F even though the message was sent?

    - by James
    As the title suggests, I've got an issue where outlook 2007 is reporting it failed to send email with error 800ccc0f (unexpectedly terminated connection) but only with attachments. The email is actually sent, but outlook keeps retrying (stays in the outbox), generating more emails to the original recipient (which do get delivered) I've got QMail on the server side supporting a half dozen domains. It doesn't appear to matter which account I send from. I can successfully send attachments via alternate mail clients (webmail, thunderbird) while outlook is failing, or send messages without attachments; so it's seemingly not the accounts themselves or serverside, which leaves outlook as the culprit. There doesn't appear to be any pattern to the failures, and it's not consistent (I successfully sent an attachment as recently as 3 weeks ago) so I'm at a loss as to where to look. Qmail logs don't look any different between successes and failures. Has anybody seen this before/have a solution? UPDATE : It appears it's only PDF files that this occurs with, so I'm even more stumped. I can send html/docx/txt and zip, UNLESS the zip file contains a pdf ... whiskey tango foxtrot

    Read the article

  • Printer irregularly producing garbage output

    - by John Gardeniers
    Every now and then instead of getting the proper output we get numerous pages, mostly with just a single line, of output which appears to be the raw PCL. My theory is that this happens when the first byte or two of the document is somehow not received by the printer, which then doesn't know how to interpret the rest and does it's best by spitting it out as text. This is a problem I've seen many times over the years but has been popping up more often since we upgraded to Win 7 64 bit, which introduced a number of headaches because of the HP lack of real support for 64 bits. It also appears to happen most often when printing PDF files. We have tried several different PDF readers in addition to Adobe's own but that hasn't helped. While we mainly use HP printers, and the problem is not limited to any particular model, I've also seen it happen on other brands, albeit to a lesser extent. I've also been unable to discern a difference between printers used via a print server or those connected directly by IP address. It also happens to USB attached printers. Because of the erratic nature of this problem there is precious little I can think of to try and debug it, so I'm after any ideas that might help to eliminate it.

    Read the article

  • How do I get the PreviewDialog of Apache FOP to actually display my document?

    - by JRSofty
    Search as I may I have not found a solution to my problem here and I'm hoping the combined minds of StackOverflow will push me in the right direction. My problem is as follows, I'm developing a print and print preview portion of a messaging system's user agent. I was given specific XSLT templates that after transforming XML will produce a Formatting Objects document. With Apache FOP I've been able to render the FO document into PDF which is all fine and good, but I would also like to display it in a print preview dialog. Apache FOP contains such a class called PreviewDialog which requires in its constructor a FOUserAgent, which I can generate, and an object implementing the Renderable Interface. The Renderable Interface has one implementing class in the FOP package which is called InputHandler which takes in its constructor a standard io File object. Now here is where the trouble begins. I'm currently storing the FO document as a temp file and pass this as a File object to an InputHandler instance which is then passed to the PreviewDialog. I see the dialog appear on my screen and along the bottom in a status bar it says that it is generating the document, and that is all it does. Here is the code I'm trying to use. It isn't production code so it's not pretty: import java.io.BufferedOutputStream; import java.io.File; import java.io.FileNotFoundException; import java.io.FileOutputStream; import java.io.IOException; import java.io.OutputStream; import java.util.Random; import javax.xml.transform.Result; import javax.xml.transform.Source; import javax.xml.transform.Transformer; import javax.xml.transform.TransformerConfigurationException; import javax.xml.transform.TransformerException; import javax.xml.transform.TransformerFactory; import javax.xml.transform.sax.SAXResult; import javax.xml.transform.stream.StreamResult; import javax.xml.transform.stream.StreamSource; import org.apache.fop.apps.FOPException; import org.apache.fop.apps.FOUserAgent; import org.apache.fop.apps.Fop; import org.apache.fop.apps.FopFactory; import org.apache.fop.cli.InputHandler; import org.apache.fop.render.awt.viewer.PreviewDialog; public class PrintPreview { public void showPreview(final File xslt, final File xmlSource) { boolean err = false; OutputStream out = null; Transformer transformer = null; final String tempFileName = this.getTempDir() + this.generateTempFileName(); final String tempFoFile = tempFileName + ".fo"; final String tempPdfFile = tempFileName + ".pdf"; System.out.println(tempFileName); final TransformerFactory transformFactory = TransformerFactory .newInstance(); final FopFactory fopFactory = FopFactory.newInstance(); try { transformer = transformFactory .newTransformer(new StreamSource(xslt)); final Source src = new StreamSource(xmlSource); out = new FileOutputStream(tempFoFile); final Result res = new StreamResult(out); transformer.transform(src, res); System.out.println("XSLT Transform Completed"); } catch (final TransformerConfigurationException e) { err = true; e.printStackTrace(); } catch (final FileNotFoundException e) { err = true; e.printStackTrace(); } catch (final TransformerException e) { err = true; e.printStackTrace(); } finally { if (out != null) { try { out.close(); } catch (final IOException e) { // TODO Auto-generated catch block e.printStackTrace(); } } } System.out.println("Initializing Preview"); transformer = null; out = null; final File fo = new File(tempFoFile); final File pdf = new File(tempPdfFile); if (!err) { final FOUserAgent ua = fopFactory.newFOUserAgent(); try { transformer = transformFactory.newTransformer(); out = new FileOutputStream(pdf); out = new BufferedOutputStream(out); final Fop fop = fopFactory.newFop( MimeConstants.MIME_PDF, ua, out); final Source foSrc = new StreamSource(fo); final Result foRes = new SAXResult(fop.getDefaultHandler()); transformer.transform(foSrc, foRes); System.out.println("Transformation Complete"); } catch (final FOPException e) { err = true; e.printStackTrace(); } catch (final FileNotFoundException e) { err = true; e.printStackTrace(); } catch (final TransformerException e) { err = true; e.printStackTrace(); } finally { if (out != null) { try { out.close(); } catch (final IOException e) { // TODO Auto-generated catch block e.printStackTrace(); } } } if (!err) { System.out.println("Attempting to Preview"); final InputHandler inputHandler = new InputHandler(fo); PreviewDialog.createPreviewDialog(ua, inputHandler, true); } } // perform the clean up // f.delete(); } private String getTempDir() { final String p = "java.io.tmpdir"; return System.getProperty(p); } private String generateTempFileName() { final String charset = "abcdefghijklmnopqrstuvwxyz1234567890abcdefghijklmnopqrstuvwxyz1234567890"; final StringBuffer sb = new StringBuffer(); Random r = new Random(); int seed = r.nextInt(); r = new Random(seed); for (int i = 0; i < 8; i++) { final int n = r.nextInt(71); seed = r.nextInt(); sb.append(charset.charAt(n)); r = new Random(seed); } return sb.toString(); } } Any help on this would be appreciated.

    Read the article

  • ASP.NET how to save textbox in database?

    - by mahsoon
    I used some textboxes to get some info from users + a sqldatasource <tr> <td class="style3" colspan="3" style="font-size: medium; font-family: 'B Nazanin'; font-weight: bold; position: relative; right: 170px" > &nbsp; ????? ??????? ????</td> </tr> <tr> <td class="style3"> &nbsp;&nbsp;&nbsp; <asp:Label ID="Label1" runat="server" Text=" ???: " Font-Bold="True" Font-Names="B Nazanin" Font-Size="Medium"></asp:Label> </td> <td class="style2"> <asp:TextBox ID="FirstName" runat="server"></asp:TextBox> </td> <td class="style4"> <asp:RequiredFieldValidator ID="RequiredFieldValidator1" runat="server" Display="Dynamic" ErrorMessage="???? ???? ??? ?????? ???" ControlToValidate="FirstName">*</asp:RequiredFieldValidator> </td> </tr> <tr> <td class="style3"> &nbsp;&nbsp;&nbsp;<asp:Label ID="Label2" runat="server" Text=" ??? ????????: " Font-Bold="True" Font-Names="B Nazanin" Font-Size="Medium"></asp:Label> </td> <td class="style2"> <asp:TextBox ID="LastName" runat="server"></asp:TextBox> </td> <td class="style4"> <asp:RequiredFieldValidator ID="RequiredFieldValidator2" runat="server" Display="Dynamic" ErrorMessage="???? ???? ??? ???????? ?????? ???" ControlToValidate="LastName">*</asp:RequiredFieldValidator> </td> </tr> <tr> <td class="style3"> &nbsp;&nbsp;&nbsp;<asp:Label ID="Label3" runat="server" Text=" ????? ???????? : " Font-Bold="True" Font-Names="B Nazanin" Font-Size="Medium"></asp:Label> </td> <td class="style2"> <asp:TextBox ID="StudentNumber" runat="server"></asp:TextBox> </td> <td class="style4"> <asp:RequiredFieldValidator ID="RequiredFieldValidator3" runat="server" Display="Dynamic" ErrorMessage="???? ???? ????? ???????? ?????? ???" ControlToValidate="StudentNumber">*</asp:RequiredFieldValidator> </td> </tr> <tr> <td class="style3"> &nbsp;&nbsp;<asp:Label ID="Label4" runat="server" Text="  ????? ???? : " Font-Bold="True" Font-Names="B Nazanin" Font-Size="Medium"></asp:Label> </td> <td class="style2"> <asp:TextBox ID="DateOfBirth" runat="server"></asp:TextBox> </td> <td class="style4"> <asp:CompareValidator ID="CompareValidator1" runat="server" Display="Dynamic" ErrorMessage="????? ???? ?????? ?? ???? ??????" Operator="DataTypeCheck" Type="Date" ControlToValidate="dateOfBirth"></asp:CompareValidator> </td> </tr> <tr> <td class="style3"> &nbsp;</td> <td class="style2"> <asp:Button ID="SaveButton" runat="server" Text=" ????? ???????" Width="102px" style="margin-right: 15px; height: 26px;" /> </td> <td class="style4"> <asp:SqlDataSource ID="SqlDataSource1" runat="server" ConnectionString="<%$ ConnectionStrings:ASPNETDBConnectionString1 %>" SelectCommand="SELECT aspnet_personalInformation.FirstName, aspnet_personalInformation.LastName, aspnet_personalInformation.StudentNumber, aspnet_personalInformation.DateOfBirth FROM aspnet_personalInformation INNER JOIN aspnet_Users ON aspnet_personalInformation.UserId = aspnet_Users.UserId WHERE aspnet_personalInformation.UserId=aspnet_Users.UserId ORDER BY aspnet_personalInformation.LastName" InsertCommand="INSERT INTO aspnet_PersonalInformation(UserId) SELECT UserId FROM aspnet_Profile"> </asp:SqlDataSource> </td> </tr> </table> i wanna save firstname lastname studentnumber and dateofbirth in aspnet_personalinformation table in database but before that, i fill one column of aspnet_personalinformation table named UserId by inserting sql command with aspnet_profile.userid now by running this code my table has still blankes protected void SaveButton_Click(object sender, EventArgs e) { string str= "Data Source=.\\SQLEXPRESS;AttachDbFilename=|DataDirectory|\\ASPNETDB.MDF;Integrated Security=True;User Instance=True"; SqlConnection con = new SqlConnection(str); con.Open(); string query = "INSERT INTO aspnet_PersonalInformation( FirstName, LastName,StudentNumber,DateOfBirth) VALUES ('" + this.FirstName.Text + "','" + this.LastName.Text + "','" + this.StudentNumber.Text + "','" + this.DateOfBirth.Text + "') where aspnet_PersonalInformation.UserId=aspnet_Profile.UserID"; SqlCommand cmd=new SqlCommand(query,con); cmd.ExecuteNonQuery(); con.Close(); } but it doesn't work help me plz

    Read the article

  • iPhone XMLParser help

    - by Brodie4598
    I am needing to parse an XML file for my app and I dont have any clue how to do it. I went through one XMLParser tutorial, and it worked fine but the XML file in the tutorial was very simple and my XML file is quite a bit more complex. here is a snippet of the xml file: <?xml version="1.0" encoding="UTF-8"?> <digital_tpp cycle="1003" from_edate="0901Z 03/11/10" to_edate="0901Z 04/08/10"> <state_code ID="AK" state_fullname="Alaska"> <city_name ID="ADAK ISLAND" volume="AK-1"> <airport_name ID="ADAK" military="N" apt_ident="ADK" icao_ident="PADK" alnum="1244"> <record> <chartseq>10100</chartseq> <chart_code>MIN</chart_code> <chart_name>TAKE-OFF MINIMUMS</chart_name> <useraction></useraction> <pdf_name>AKTO.PDF</pdf_name> <cn_flg>N</cn_flg> <cnsection></cnsection> <cnpage></cnpage> <bvsection>C</bvsection> <bvpage></bvpage> <procuid></procuid> <two_colored>N</two_colored> <civil> </civil> <faanfd15></faanfd15> <faanfd18></faanfd18> <copter></copter> </record> <record> <chartseq>10200</chartseq> <chart_code>MIN</chart_code> <chart_name>ALTERNATE MINIMUMS</chart_name> <useraction></useraction> <pdf_name>AKALT.PDF</pdf_name> <cn_flg>N</cn_flg> <cnsection></cnsection> <cnpage></cnpage> <bvsection>E</bvsection> <bvpage></bvpage> <procuid></procuid> <two_colored>N</two_colored> <civil> </civil> <faanfd15></faanfd15> <faanfd18></faanfd18> <copter></copter> </record> </airport_name> </city_name> </state_code> </digital_tpp> What I'm needing to do is search the XML file for the <...icao_ident> that the user specifies, then create a dictionary containing the <pdf_name> and <chart_name> for each <record> . I will then create a UI that displays the pdf files. Can someone direct me to a good tutorial or explanation of how XML parser works? Or if I'm going about this the wrong way I'd be open to suggestions too. (the XML file is about 8MB)

    Read the article

  • Can connect to Samba server but cannot access shares?

    - by jlego
    I have setup a stand-alone box running Fedora 16 to use as a file-sharing and web development server. Needs to be able to share files with a PC running Windows 7 and a Mac running OSX Snow Leopard. I've setup Samba using the Samba configuration GUI tool. Added users to Fedora and connected them as Samba users (which are the same as the Windows and Mac usernames and passwords). The workgroup name is the same as the Windows workgroup. Authentication is set to User. I've allowed Samba and Samba client through the firewall and set the ethernet to a trusted port in the firewall. Both the Windows and Mac machines can connect to the server and view the shares, however when trying to access the shares, Windows throws error 0x80070035 " Windows cannot access \SERVERNAME\ShareName." Windows user is not prompted for a username or password when accessing the server (found under "Network Places"). This also happens when connecting with the IP rather than the server name. The Mac can also connect to the server and see the shares but when choosing a share gives the error "The original item for ShareName cannot be found." When connecting via IP, the Mac user is prompted for username and password, which when authenticated gives a list of shares, however when choosing a share to connect to, the error is displayed and the user cannot access the share. Since both machines are acting similarly when trying to access the shares, I assume it is an issue with how Samba is configured. smb.conf: [global] workgroup = workgroup server string = Server log file = /var/log/samba/log.%m max log size = 50 security = user load printers = yes cups options = raw printcap name = lpstat printing = cups [homes] comment = Home Directories browseable = no writable = yes [printers] comment = All Printers path = /var/spool/samba browseable = yes printable = yes [FileServ] comment = FileShare path = /media/FileServ read only = no browseable = yes valid users = user1, user2 [webdev] comment = Web development path = /var/www/html/webdev read only = no browseable = yes valid users = user1 How do I get samba sharing working? UPDATE: Before this box I had another box with the same version of fedora installed (16) and samba working for these same computers. I started up the old machine and copied the smb.conf file from the old machine to the new one (editing the share definitions for the new shares of course) and I still get the same errors on both client machines. The only difference in environment is the hardware and the router. On the old machine the router received a dynamic public IP and assigned dynamic private IPs to each device on the network while the new machine is connected to a router that has a static public IP (still dynamic internal IPs though.) Could either one of these be affecting Samba? UPDATE 2: As the directory I am trying to share is actually an entire internal disk, I have tried to things: 1.) changing the owner of the mounted disk from root to my user (which is the same username as on the Windows machine) 2.) made a share that only included one of the folders on the disk instead of the entire disk with my user again as the owner. Both tests failed giving me the same errors regarding the network address. UPDATE 3: Not sure exactly what I did, but now whenever I try to connect to the share on the Windows 7 client I am prompted for my username and password. When I enter the correct credentials I get an access denied message. However I did notice that under the login box "domain: WINDOWS-PC-NAME" is listed. I believe this could very well be the problem. Any suggestions? UPDATE 4: So I've completely reinstalled Fedora and Samba now. I've created a share on the first harddrive (one fedora is installed on) and I can access that fine from Windows. However when I try to share any data on the second disk, I am receiving the same error. This I believe is the problem. I think I need to change some things in fstab or fdisk or something. UPDATE 5: So in fstab I mapped the drive to automount in a folder which works correctly. I also added the samba_share_t SElinux label to the mountpoint directory which now allows me to access the shares on the Windows machine, however I cannot see any of the files in the directory on the windows machine. (They are there, I can see them in the fedora file browser locally) UPDATE 6: Figured it out. See answer below

    Read the article

  • OSX 10.6 Cisco IPSEC strange behavior

    - by tair
    I'm trying to connect to Cisco IPSEC VPN of my company over DSL Internet. I managed to successfully connect using Cisco VPN Client, now I'm trying to switch to OSX 10.6 native client, because of licensing issues. The problems is that the connection fails with a dialog box containing the message: The negotiation with the VPN server failed. Verify the server address and try reconnecting. I checked logs: Jun 29 13:10:39 racoon[4551]: Connecting. Jun 29 13:10:39 racoon[4551]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1). Jun 29 13:10:39 racoon[4551]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2). Jun 29 13:10:39 racoon[4551]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2). Jun 29 13:10:39 racoon[4551]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode). Jun 29 13:10:39 racoon[4551]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3). Jun 29 13:10:42 racoon[4551]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:10:42 racoon[4551]: IKEv1 XAUTH: success. (XAUTH Status is OK). Jun 29 13:10:42 racoon[4551]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:10:42 racoon[4551]: IKEv1 Config: retransmited. (Mode-Config retransmit). Jun 29 13:10:42 racoon[4551]: IKE Packet: receive success. (MODE-Config). Jun 29 13:10:42 configd[19]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.1.107), current interface setting (name: u92.168.54.147, subnet: 255.255.255.0, destination: 192.168.54.147). Jun 29 13:10:42 configd[19]: network configuration changed. Jun 29 13:10:42 vmnet-bridge[111]: Dynamic store changed Jun 29 13:10:42 named[62]: not listening on any interfaces Jun 29 13:10:58: --- last message repeated 1 time --- Jun 29 13:10:58 configd[19]: SCNCController: Disconnecting. (Connection tried to negotiate for, 16 seconds). Jun 29 13:10:58 racoon[4551]: IKE Packet: transmit success. (Information message). Jun 29 13:10:58 racoon[4551]: IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA). Jun 29 13:10:58 racoon[4551]: Disconnecting. (Connection tried to negotiate for, 19.113382 seconds). Jun 29 13:10:58 named[62]: not listening on any interfaces Jun 29 13:10:58 vmnet-bridge[111]: Dynamic store changed Jun 29 13:10:58 named[62]: not listening on any interfaces Jun 29 13:10:58 configd[19]: network configuration changed. Then I opened Terminal, started pinging a server behind VPN, and tried to connect again. Now connection is OK! Logs this time: Jun 29 13:46:53 racoon[8136]: Connecting. Jun 29 13:46:53 racoon[8136]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1). Jun 29 13:46:53 racoon[8136]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2). Jun 29 13:46:53 racoon[8136]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2). Jun 29 13:46:53 racoon[8136]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode). Jun 29 13:46:53 racoon[8136]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:46:56 racoon[8136]: IKEv1 XAUTH: success. (XAUTH Status is OK). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:46:56 racoon[8136]: IKEv1 Config: retransmited. (Mode-Config retransmit). Jun 29 13:46:56 racoon[8136]: IKE Packet: receive success. (MODE-Config). Jun 29 13:46:56 configd[19]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.1.107), current interface settinaddress: 192.168.54.149, subnet: 255.255.255.0, destination: 192.168.54.149). Jun 29 13:46:56 vmnet-bridge[111]: Dynamic store changed Jun 29 13:46:56 named[62]: not listening on any interfaces Jun 29 13:46:56 configd[19]: network configuration changed. Jun 29 13:46:56 named[62]: not listening on any interfaces Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1). Jun 29 13:46:56 racoon[8136]: IKE Packet: receive success. (Initiator, Quick-Mode message 2). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3). Jun 29 13:46:56 racoon[8136]: IKEv1 Phase2 Initiator: success. (Initiator, Quick-Mode). Jun 29 13:46:56 racoon[8136]: Connected. Jun 29 13:46:56 configd[19]: SCNCController: Connected. I tested it several times and it consistently behaves the same. What is the magic?

    Read the article

  • Python RSS Feeder + Jquery RSS Reader

    - by Panther24
    I'm trying to implement an RSS Feeder in python using PyRSS2Gen and it created an XML file. Now in jQuery I'm using Google Ajax API's RSS reader and trying to read it. I get an error saying something is wrong. I'm unable to figure out the issue. I've checked some documentation but not able to get it. This is how my xml file looks: <rss version="2.0"> <channel> <title>Andrew's PyRSS2Gen feed</title> <link> http://www.dalkescientific.com/Python/PyRSS2Gen.html </link> <description> The latest news about PyRSS2Gen, a Python library for generating RSS2 feeds </description> <lastBuildDate>Fri, 26 Mar 2010 13:10:55 GMT</lastBuildDate> <generator>PyRSS2Gen-1.0.0</generator> <docs>http://blogs.law.harvard.edu/tech/rss</docs> <item> <title>PyRSS2Gen-0.0 released</title> <link> http://www.dalkescientific.com/news/030906-PyRSS2Gen.html </link> <description> Dalke Scientific today announced PyRSS2Gen-0.0, a library for generating RSS feeds for Python. </description> <guid isPermaLink="true"> http://www.dalkescientific.com/news/030906-PyRSS2Gen.html </guid> <pubDate>Sat, 06 Sep 2003 21:31:00 GMT</pubDate> </item> <item> <title>Thoughts on RSS feeds for bioinformatics</title> <link> http://www.dalkescientific.com/writings/diary/archive/2003/09/06/RSS.html </link> <description> One of the reasons I wrote PyRSS2Gen was to experiment with RSS for data collection in bioinformatics. Last year I came across... </description> <guid isPermaLink="true"> http://www.dalkescientific.com/writings/diary/archive/2003/09/06/RSS.html </guid> <pubDate>Sat, 06 Sep 2003 21:49:00 GMT</pubDate> </item> </channel> </rss> And my JS looks like this <!-- ++Begin Dynamic Feed Wizard Generated Code++ --> <!-- // Created with a Google AJAX Search and Feed Wizard // http://code.google.com/apis/ajaxsearch/wizards.html --> <!-- // The Following div element will end up holding the actual feed control. // You can place this anywhere on your page. --> <!-- Google Ajax Api --> <script src="../js/jsapi.js" type="text/javascript"></script> <!-- Dynamic Feed Control and Stylesheet --> <script src="../js/gfdynamicfeedcontrol.js" type="text/javascript"></script> <link rel="stylesheet" type="text/css" href="../css/gfdynamicfeedcontrol.css"> <script type="text/javascript"> function LoadDynamicFeedControl() { var feeds = [ {title: 'Demo', url: 'wcarss.xml' }]; var options = { stacked : false, horizontal : false, title : "" } new GFdynamicFeedControl(feeds, 'feed-control', options); } // Load the feeds API and set the onload callback. google.load('feeds', '1'); google.setOnLoadCallback(LoadDynamicFeedControl); </script> <!-- ++End Dynamic Feed Control Wizard Generated Code++ --> Can some help me and tell me what I'm doing wrong here? NOTE: Does the XML file have to be deployed? Cause currently its in my local machine and I'm trying to just call it.

    Read the article

  • OSX 10.6 Cisco IPSEC strange behavior

    - by tair
    I'm trying to connect to Cisco IPSEC VPN of my company over DSL Internet. I managed to successfully connect using Cisco VPN Client, now I'm trying to switch to OSX 10.6 native client, because of licensing issues. The problems is that the connection fails with a dialog box containing the message: The negotiation with the VPN server failed. Verify the server address and try reconnecting. I checked logs: Jun 29 13:10:39 racoon[4551]: Connecting. Jun 29 13:10:39 racoon[4551]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1). Jun 29 13:10:39 racoon[4551]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2). Jun 29 13:10:39 racoon[4551]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2). Jun 29 13:10:39 racoon[4551]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode). Jun 29 13:10:39 racoon[4551]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3). Jun 29 13:10:42 racoon[4551]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:10:42 racoon[4551]: IKEv1 XAUTH: success. (XAUTH Status is OK). Jun 29 13:10:42 racoon[4551]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:10:42 racoon[4551]: IKEv1 Config: retransmited. (Mode-Config retransmit). Jun 29 13:10:42 racoon[4551]: IKE Packet: receive success. (MODE-Config). Jun 29 13:10:42 configd[19]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.1.107), current interface setting (name: u92.168.54.147, subnet: 255.255.255.0, destination: 192.168.54.147). Jun 29 13:10:42 configd[19]: network configuration changed. Jun 29 13:10:42 vmnet-bridge[111]: Dynamic store changed Jun 29 13:10:42 named[62]: not listening on any interfaces Jun 29 13:10:58: --- last message repeated 1 time --- Jun 29 13:10:58 configd[19]: SCNCController: Disconnecting. (Connection tried to negotiate for, 16 seconds). Jun 29 13:10:58 racoon[4551]: IKE Packet: transmit success. (Information message). Jun 29 13:10:58 racoon[4551]: IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA). Jun 29 13:10:58 racoon[4551]: Disconnecting. (Connection tried to negotiate for, 19.113382 seconds). Jun 29 13:10:58 named[62]: not listening on any interfaces Jun 29 13:10:58 vmnet-bridge[111]: Dynamic store changed Jun 29 13:10:58 named[62]: not listening on any interfaces Jun 29 13:10:58 configd[19]: network configuration changed. Then I opened Terminal, started pinging a server behind VPN, and tried to connect again. Now connection is OK! Logs this time: Jun 29 13:46:53 racoon[8136]: Connecting. Jun 29 13:46:53 racoon[8136]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1). Jun 29 13:46:53 racoon[8136]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2). Jun 29 13:46:53 racoon[8136]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2). Jun 29 13:46:53 racoon[8136]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode). Jun 29 13:46:53 racoon[8136]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:46:56 racoon[8136]: IKEv1 XAUTH: success. (XAUTH Status is OK). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:46:56 racoon[8136]: IKEv1 Config: retransmited. (Mode-Config retransmit). Jun 29 13:46:56 racoon[8136]: IKE Packet: receive success. (MODE-Config). Jun 29 13:46:56 configd[19]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.1.107), current interface settinaddress: 192.168.54.149, subnet: 255.255.255.0, destination: 192.168.54.149). Jun 29 13:46:56 vmnet-bridge[111]: Dynamic store changed Jun 29 13:46:56 named[62]: not listening on any interfaces Jun 29 13:46:56 configd[19]: network configuration changed. Jun 29 13:46:56 named[62]: not listening on any interfaces Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1). Jun 29 13:46:56 racoon[8136]: IKE Packet: receive success. (Initiator, Quick-Mode message 2). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3). Jun 29 13:46:56 racoon[8136]: IKEv1 Phase2 Initiator: success. (Initiator, Quick-Mode). Jun 29 13:46:56 racoon[8136]: Connected. Jun 29 13:46:56 configd[19]: SCNCController: Connected. I tested it several times and it consistently behaves the same. What is the magic?

    Read the article

  • Error while rendering report(.rdl).

    - by Sushavon Banerjee
    Hi, I have generated a .rdl report file. Now, when I am going to render the .rdl report file into pdf format,exception is throwing. The exception is : - "An error occurred during local report processing." The stack trace is follows : - " at Microsoft.Reporting.WebForms.LocalReport.InternalRender(String format, Boolean allowInternalRenderers, String deviceInfo, CreateAndRegisterStream createStreamCallback, Warning[]& warnings)\r\n at Microsoft.Reporting.WebForms.LocalReport.InternalRender(String format, Boolean allowInternalRenderers, String deviceInfo, String& mimeType, String& encoding, String& fileNameExtension, String[]& streams, Warning[]& warnings)\r\n at Microsoft.Reporting.WebForms.LocalReport.Render(String format, String deviceInfo, String& mimeType, String& encoding, String& fileNameExtension, String[]& streams, Warning[]& warnings)\r\n at SaltlakeSoft.APEX2.Controllers.TestPageController.RenderReport() in E:\Documents and Settings\Administrator\Desktop\afetbuild15thmayapex2\apex2\Controllers\TestPageController.cs:line 1626\r\n at lambda_method(ExecutionScope , ControllerBase , Object[] )\r\n at System.Web.Mvc.ActionMethodDispatcher.<c_DisplayClass1.b_0(ControllerBase controller, Object[] parameters)\r\n at System.Web.Mvc.ActionMethodDispatcher.Execute(ControllerBase controller, Object[] parameters)\r\n at System.Web.Mvc.ReflectedActionDescriptor.Execute(ControllerContext controllerContext, IDictionary2 parameters)\r\n at System.Web.Mvc.ControllerActionInvoker.InvokeActionMethod(ControllerContext controllerContext, ActionDescriptor actionDescriptor, IDictionary2 parameters)\r\n at System.Web.Mvc.ControllerActionInvoker.<c_DisplayClassa.b_7()\r\n at System.Web.Mvc.ControllerActionInvoker.InvokeActionMethodFilter(IActionFilter filter, ActionExecutingContext preContext, Func`1 continuation)" My code is as follows : - LocalReport report = new LocalReport(); report.ReportPath = @"E:\Report1.rdl"; List<Employee> employeeCollection = empRepository.FindAll().ToList(); ReportDataSource reportDataSource = new ReportDataSource("dataSource1",employeeCollection); report.DataSources.Clear(); report.DataSources.Add(reportDataSource); report.Refresh(); string reportType = "PDF"; string mimeType; string encoding; string fileNameExtension; string deviceInfo ="<DeviceInfo>" +"<OutputFormat>PDF</OutputFormat>" + "<PageWidth>8.5in</PageWidth>" + "<PageHeight>11in</PageHeight>" + "<MarginTop>0.5in</MarginTop>" +"<MarginLeft>1in</MarginLeft>" + "<MarginRight>1in</MarginRight>" +"<MarginBottom>0.5in</MarginBottom>" + "</DeviceInfo>"; Warning[] warnings; string[] streams; byte[] renderedBytes; renderedBytes = report.Render(reportType,deviceInfo,out mimeType,out encoding, out fileNameExtension, out streams, out warnings); Response.Clear(); Response.ContentType = mimeType; Response.AddHeader("content-disposition", "attachment; filename=foo." + fileNameExtension); Response.BinaryWrite(renderedBytes); Response.End(); Help me please... Thanks, Sushavon

    Read the article

  • Adding UL to jQuery UI Tabs

    - by Dave Kiss
    It seems like whenever I try to add a UL inside of the containers when using jQuery UI - Tabs, it breaks the javascript. Is there a way I can use a UL inside of these containers that I am missing? Thanks <div id="tabs"> <div id="fragment-1"> <h4>Pre-Press Requirements</h4> ? SAMPLE of final artwork with noted sizes. ? NATIVE FILES & High Resolution PDF preferred. Files must be created or saved to the listed accepted file formats. ? FONTS used in files need to be supplied in a separate folder marked "fonts". Please ensure all families (screen & printer) fonts are supplied for the job. ? IMAGES must be saved as CMYK and no less than 300dpi. NO RGB FILES! We prefer images to be TIF or EPS formats. If you are submitting artwork for spot color printing vector artwork is preferred. Your images should be supplied in a separate folder marked "links". This will ensure proper reproduction of your artwork. ? COLORS need to be clearly specified. Pantone (PMS) colors preferred. Please specify if job is to be printed CMYK, spot color, etc. ? BLEEDS should be no less than .25" ? PDF's should be High Resolution. Please include any spot colors or CMYK format for full color printing. NO RGB FILES! All bleeds should be included with trim marks. All fonts must be embedded or outlined. No "layered" PDF files. </div> <div id="fragment-2"> <p>Our presses are all capable of sizes up to 11" x 17" using spot color or full color.</p> </div> <div id="fragment-3"> <p>USA Quickprint has complete in house bindery to finish each job to meet your needs.</p> <ul> <li>Folding</li> <li>Scoring</li> <li>Perforation</li> <li>Drilling</li> <li>Shrink Wrap</li> <li>Trimming</li> <li>Collating</li> <li>Spiral Binding</li> <li>GBC Binding</li> <li>Padding</li> <li>Stapling</li> <li>Numbering</li> <li>Lamination</li> </ul> </div>

    Read the article

  • Cannot find Package fop ( Ithink)

    - by efendioglu
    Hello friends I try to use fop engine programatically I search for an example and I find this class import java.io.File; import java.io.IOException; import java.io.OutputStream; import javax.xml.transform.Transformer; import javax.xml.transform.TransformerFactory; import javax.xml.transform.TransformerException; import javax.xml.transform.Source; import javax.xml.transform.Result; import javax.xml.transform.stream.StreamSource; import javax.xml.transform.sax.SAXResult; import org.apache.avalon.framework.ExceptionUtil; import org.apache.avalon.framework.logger.ConsoleLogger; import org.apache.avalon.framework.logger.Logger; import org.apache.fop.apps.Driver; import org.apache.fop.apps.FOPException; import org.apache.fop.messaging.MessageHandler; public class Invokefop { public void convertXML2PDF(File xml, File xslt, File pdf) throws IOException, FOPException, TransformerException { Driver driver = new Driver(); Logger logger = new ConsoleLogger(ConsoleLogger.LEVEL_INFO); driver.setLogger(logger); MessageHandler.setScreenLogger(logger); driver.setRenderer(Driver.RENDER_PDF); OutputStream out = new java.io.FileOutputStream(pdf); try { driver.setOutputStream(out); TransformerFactory factory = TransformerFactory.newInstance(); Transformer transformer = factory.newTransformer(new StreamSource(xslt)); Source src = new StreamSource(xml); Result res = new SAXResult(driver.getContentHandler()); transformer.transform(src, res); } finally { out.close(); } } public static void main(String[] args) { try { System.out.println("JAVA XML2PDF:: FOP ExampleXML2PDF\n"); System.out.println("JAVA XML2PDF:: Preparing..."); File base = new File("../"); File baseDir = new File(base, "in"); File outDir = new File(base, "out"); outDir.mkdirs(); File xmlfile = new File(baseDir, args[0]); File xsltfile = new File(baseDir, args[1]); File pdffile = new File(outDir, args[2]); System.out.println("JAVA XML2PDF:: Input: XML (" + xmlfile + ")"); System.out.println("JAVA XML2PDF:: Stylesheet: " + xsltfile); System.out.println("JAVA XML2PDF:: Output: PDF (" + pdffile + ")"); System.out.println(); System.out.println("JAVA XML2PDF:: Transforming..."); Invokefop app = new Invokefop(); app.convertXML2PDF(xmlfile, xsltfile, pdffile); System.out.println("JAVA XML2PDF:: Success!"); } catch (Exception e) { System.err.println(ExceptionUtil.printStackTrace(e)); System.exit(-1); } } } All the Libs from Fop are in the Classpath including the fop.jar in build directory. After I run thejavac Invokefop.java I get this error: > C:\....\fop>javac Invokefop.java Invokefop.java:21: cannot find symbol symbol : class Driver location: package org.apache.fop.apps import org.apache.fop.apps.Driver; ^ Invokefop.java:23: package org.apache.fop.messaging does not exist import org.apache.fop.messaging.MessageHandler; ^ Invokefop.java:31: cannot find symbol symbol : class Driver location: class Invokefop Driver driver = new Driver(); ^ Invokefop.java:31: cannot find symbol symbol : class Driver location: class Invokefop Driver driver = new Driver(); ^ Invokefop.java:36: cannot find symbol symbol : variable MessageHandler location: class Invokefop MessageHandler.setScreenLogger(logger); ^ Invokefop.java:39: cannot find symbol symbol : variable Driver location: class Invokefop driver.setRenderer(Driver.RENDER_PDF); ^ 6 errors I am relatively new to Java, but with this approach I try to execute the fop engine in c++ using this java class.. Have anybody some Idea, how to solve this errors... Thanx in advance..

    Read the article

  • Problem exporting NSOpenGLView pixel data to some image file formats using ImageKit & CGImageDestina

    - by walkytalky
    I am developing an application to visualise some experimental data. One of its functions is to render the data in an NSOpenGLView subclass, and allow the resulting image to be exported to a file or copied to the clipboard. The view exports the data as an NSImage, generated like this: - (NSImage*) image { NSBitmapImageRep* imageRep; NSImage* image; NSSize viewSize = [self bounds].size; int width = viewSize.width; int height = viewSize.height; [self lockFocus]; [self drawRect:[self bounds]]; [self unlockFocus]; imageRep=[[[NSBitmapImageRep alloc] initWithBitmapDataPlanes:NULL pixelsWide:width pixelsHigh:height bitsPerSample:8 samplesPerPixel:4 hasAlpha:YES isPlanar:NO colorSpaceName:NSDeviceRGBColorSpace bytesPerRow:width*4 bitsPerPixel:32] autorelease]; [[self openGLContext] makeCurrentContext]; glReadPixels(0,0,width,height,GL_RGBA,GL_UNSIGNED_BYTE,[imageRep bitmapData]); image=[[[NSImage alloc] initWithSize:NSMakeSize(width,height)] autorelease]; [image addRepresentation:imageRep]; [image setFlipped:YES]; // this is deprecated in 10.6 [image lockFocusOnRepresentation:imageRep]; // this will flip the rep [image unlockFocus]; return image; } Copying uses this image very simply, like this: - (IBAction) copy:(id) sender { NSImage* img = [self image]; NSPasteboard* pb = [NSPasteboard generalPasteboard]; [pb clearContents]; NSArray* copied = [NSArray arrayWithObject:img]; [pb writeObjects:copied]; } For file writing, I use the ImageKit IKSaveOptions accessory panel to set the output file type and associated options, then use the following code to do the writing: NSImage* glImage = [glView image]; NSRect rect = [glView bounds]; rect.origin.x = rect.origin.y = 0; img = [glImage CGImageForProposedRect:&rect context:[NSGraphicsContext currentContext] hints:nil]; if (img) { NSURL* url = [NSURL fileURLWithPath: path]; CGImageDestinationRef dest = CGImageDestinationCreateWithURL((CFURLRef)url, (CFStringRef)newUTType, 1, NULL); if (dest) { CGImageDestinationAddImage(dest, img, (CFDictionaryRef)[imgSaveOptions imageProperties]); CGImageDestinationFinalize(dest); CFRelease(dest); } } (I've trimmed a bit of extraneous code here, but nothing that would affect the outcome as far as I can see. The newUTType comes from the IKSaveOptions panel.) This works fine when the file is exported as GIF, JPEG, PNG, PSD or TIFF, but exporting to PDF, BMP, TGA, ICNS and JPEG-2000 produces a red colour artefact on part of the image. Example images are below, the first exported as JPG, the second as PDF. Copy to clipboard does not exhibit this red stripe with the current implementation of image, but it did with the original implementation, which generated the imageRep using NSCalibratedRGBColorSpace rather than NSDeviceRGBColorSpace. So I'm guessing there's some issue with the colour representation in the pixels I get from OpenGL that doesn't get through the subsequent conversions properly, but I'm at a loss as to what to do about it. So, can anyone tell me (i) what is causing this, and (ii) how can I make it go away? I don't care so much about all of the formats but I'd really like at least PDF to work.

    Read the article

  • Paging, sorting and filtering in a stored procedure (SQL Server)

    - by Fruitbat
    I was looking at different ways of writing a stored procedure to return a "page" of data. This was for use with the asp ObjectDataSource, but it could be considered a more general problem. The requirement is to return a subset of the data based on the usual paging paremeters, startPageIndex and maximumRows, but also a sortBy parameter to allow the data to be sorted. Also there are some parameters passed in to filter the data on various conditions. One common way to do this seems to be something like this: [Method 1] ;WITH stuff AS ( SELECT CASE WHEN @SortBy = 'Name' THEN ROW_NUMBER() OVER (ORDER BY Name) WHEN @SortBy = 'Name DESC' THEN ROW_NUMBER() OVER (ORDER BY Name DESC) WHEN @SortBy = ... ELSE ROW_NUMBER() OVER (ORDER BY whatever) END AS Row, ., ., ., FROM Table1 INNER JOIN Table2 ... LEFT JOIN Table3 ... WHERE ... (lots of things to check) ) SELECT * FROM stuff WHERE (Row > @startRowIndex) AND (Row <= @startRowIndex + @maximumRows OR @maximumRows <= 0) ORDER BY Row One problem with this is that it doesn't give the total count and generally we need another stored procedure for that. This second stored procedure has to replicate the parameter list and the complex WHERE clause. Not nice. One solution is to append an extra column to the final select list, (SELECT COUNT(*) FROM stuff) AS TotalRows. This gives us the total but repeats it for every row in the result set, which is not ideal. [Method 2] An interesting alternative is given here (http://www.4guysfromrolla.com/articles/032206-1.aspx) using dynamic SQL. He reckons that the performance is better because the CASE statement in the first solution drags things down. Fair enough, and this solution makes it easy to get the totalRows and slap it into an output parameter. But I hate coding dynamic SQL. All that 'bit of SQL ' + STR(@parm1) +' bit more SQL' gubbins. [Method 3] The only way I can find to get what I want, without repeating code which would have to be synchronised, and keeping things reasonably readable is to go back to the "old way" of using a table variable: DECLARE @stuff TABLE (Row INT, ...) INSERT INTO @stuff SELECT CASE WHEN @SortBy = 'Name' THEN ROW_NUMBER() OVER (ORDER BY Name) WHEN @SortBy = 'Name DESC' THEN ROW_NUMBER() OVER (ORDER BY Name DESC) WHEN @SortBy = ... ELSE ROW_NUMBER() OVER (ORDER BY whatever) END AS Row, ., ., ., FROM Table1 INNER JOIN Table2 ... LEFT JOIN Table3 ... WHERE ... (lots of things to check) SELECT * FROM stuff WHERE (Row > @startRowIndex) AND (Row <= @startRowIndex + @maximumRows OR @maximumRows <= 0) ORDER BY Row (Or a similar method using an IDENTITY column on the table variable). Here I can just add a SELECT COUNT on the table variable to get the totalRows and put it into an output parameter. I did some tests and with a fairly simple version of the query (no sortBy and no filter), method 1 seems to come up on top (almost twice as quick as the other 2). Then I decided to test probably I needed the complexity and I needed the SQL to be in stored procedures. With this I get method 1 taking nearly twice as long as the other 2 methods. Which seems strange. Is there any good reason why I shouldn't spurn CTEs and stick with method 3? UPDATE - 15 March 2012 I tried adapting Method 1 to dump the page from the CTE into a temporary table so that I could extract the TotalRows and then select just the relevant columns for the resultset. This seemed to add significantly to the time (more than I expected). I should add that I'm running this on a laptop with SQL Server Express 2008 (all that I have available) but still the comparison should be valid. I looked again at the dynamic SQL method. It turns out I wasn't really doing it properly (just concatenating strings together). I set it up as in the documentation for sp_executesql (with a parameter description string and parameter list) and it's much more readable. Also this method runs fastest in my environment. Why that should be still baffles me, but I guess the answer is hinted at in Hogan's comment.

    Read the article

  • PHP - Code Sample - Polymorphism Implementation - How to allow for expansion?

    - by darga33
    I've read numerous SO posts about Polymorphism, and also the other really good one at http://net.tutsplus.com/tutorials/php/understanding-and-applying-polymorphism-in-php/ Good stuff!!! I'm trying to figure out how a seasoned PHP developer that follows all the best practices would accomplish the following. Please be as specific and detailed as possible. I'm sure your answer is going to help a lot of people!!! :-) While learning Polymorphism, I came across a little stumbling block. Inside of the PDFFormatter class, I had to use (instanceof) in order to figure out if some code should be included in the returned data. I am trying to be able to pass in two different kinds of profiles to the formatter. (needs to be able to handle multiple kinds of formatters but display the data specific to the Profile class that is being passed to it). It doesn't look bad now, but imagine 10 more kinds of Profiles!! How would you do this? The best answer would also include the changes you would make. Thanks sooooooo much in advance!!!!! Please PHP only! Thx!!! File 1. FormatterInterface.php interface FormatterInterface { public function format(Profile $Profile); } File 2. PDFFormatter.php class PDFFormatter implements FormatterInterface { public function format(Profile $Profile) { $format = "PDF Format<br /><br />"; $format .= "This is a profile formatted as a PDF.<br />"; $format .= 'Name: ' . $Profile->name . '<br />'; if ($Profile instanceof StudentProfile) { $format .= "Graduation Date: " . $Profile->graduationDate . "<br />"; } $format .= "<br />End of PDF file"; return $format; } } File 3. Profile.php class Profile { public $name; public function __construct($name) { $this->name = $name; } public function format(FormatterInterface $Formatter) { return $Formatter->format($this); } } File 4. StudentProfile.php class StudentProfile extends Profile { public $graduationDate; public function __construct($name, $graduationDate) { $this->name = $name; $this->graduationDate = $graduationDate; } } File 5. index.php //Assuming all files are included...... $StudentProfile = new StudentProfile('Michael Conner', 55, 'Unknown, FL', 'Graduate', '1975', 'Business Management'); $Profile = new Profile('Brandy Smith', 44, 'Houston, TX'); $PDFFormatter = new PDFFormatter(); echo '<hr />'; echo $StudentProfile->format($PDFFormatter); echo '<hr />'; echo $Profile->format($PDFFormatter);

    Read the article

  • Creating a custom module for Orchard

    - by Moran Monovich
    I created a custom module using this guide from Orchard documentation, but for some reason I can't see the fields in the content type when I want to create a new one. this is my model: public class CustomerPartRecord : ContentPartRecord { public virtual string FirstName { get; set; } public virtual string LastName { get; set; } public virtual int PhoneNumber { get; set; } public virtual string Address { get; set; } public virtual string Profession { get; set; } public virtual string ProDescription { get; set; } public virtual int Hours { get; set; } } public class CustomerPart : ContentPart<CustomerPartRecord> { [Required(ErrorMessage="you must enter your first name")] [StringLength(200)] public string FirstName { get { return Record.FirstName; } set { Record.FirstName = value; } } [Required(ErrorMessage = "you must enter your last name")] [StringLength(200)] public string LastName { get { return Record.LastName; } set { Record.LastName = value; } } [Required(ErrorMessage = "you must enter your phone number")] [DataType(DataType.PhoneNumber)] public int PhoneNumber { get { return Record.PhoneNumber; } set { Record.PhoneNumber = value; } } [StringLength(200)] public string Address { get { return Record.Address; } set { Record.Address = value; } } [Required(ErrorMessage = "you must enter your profession")] [StringLength(200)] public string Profession { get { return Record.Profession; } set { Record.Profession = value; } } [StringLength(500)] public string ProDescription { get { return Record.ProDescription; } set { Record.ProDescription = value; } } [Required(ErrorMessage = "you must enter your hours")] public int Hours { get { return Record.Hours; } set { Record.Hours = value; } } } this is the Handler: class CustomerHandler : ContentHandler { public CustomerHandler(IRepository<CustomerPartRecord> repository) { Filters.Add(StorageFilter.For(repository)); } } the Driver: class CustomerDriver : ContentPartDriver<CustomerPart> { protected override DriverResult Display(CustomerPart part, string displayType, dynamic shapeHelper) { return ContentShape("Parts_Customer", () => shapeHelper.Parts_BankCustomer( FirstName: part.FirstName, LastName: part.LastName, PhoneNumber: part.PhoneNumber, Address: part.Address, Profession: part.Profession, ProDescription: part.ProDescription, Hours: part.Hours)); } //GET protected override DriverResult Editor(CustomerPart part, dynamic shapeHelper) { return ContentShape("Parts_Customer", () => shapeHelper.EditorTemplate( TemplateName:"Parts/Customer", Model: part, Prefix: Prefix)); } //POST protected override DriverResult Editor(CustomerPart part, IUpdateModel updater, dynamic shapeHelper) { updater.TryUpdateModel(part, Prefix, null, null); return Editor(part, shapeHelper); } the migration: public class Migrations : DataMigrationImpl { public int Create() { // Creating table CustomerPartRecord SchemaBuilder.CreateTable("CustomerPartRecord", table => table .ContentPartRecord() .Column("FirstName", DbType.String) .Column("LastName", DbType.String) .Column("PhoneNumber", DbType.Int32) .Column("Address", DbType.String) .Column("Profession", DbType.String) .Column("ProDescription", DbType.String) .Column("Hours", DbType.Int32) ); return 1; } public int UpdateFrom1() { ContentDefinitionManager.AlterPartDefinition("CustomerPart", builder => builder.Attachable()); return 2; } public int UpdateFrom2() { ContentDefinitionManager.AlterTypeDefinition("Customer", cfg => cfg .WithPart("CommonPart") .WithPart("RoutePart") .WithPart("BodyPart") .WithPart("CustomerPart") .WithPart("CommentsPart") .WithPart("TagsPart") .WithPart("LocalizationPart") .Creatable() .Indexed()); return 3; } } Can someone please tell me if I am missing something?

    Read the article

  • Using CreateSourceQuery in CTP4 Code First

    - by Adam Rackis
    I'm guessing this is impossible, but I'll throw it out there anyway. Is it possible to use CreateSourceQuery when programming with the EF4 CodeFirst API, in CTP4? I'd like to eagerly load properties attached to a collection of properties, like this: var sourceQuery = this.CurrentInvoice.PropertyInvoices.CreateSourceQuery(); sourceQuery.Include("Property").ToList(); But of course CreateSourceQuery is defined on EntityCollection<T>, whereas CodeFirst uses plain old ICollection (obviously). Is there some way to convert? I've gotten the below to work, but it's not quite what I'm looking for. Anyone know how to go from what's below to what's above (code below is from a class that inherits DbContext)? ObjectSet<Person> OSPeople = base.ObjectContext.CreateObjectSet<Person>(); OSPeople.Include(Pinner => Pinner.Books).ToList(); Thanks! EDIT: here's my version of the solution posted by zeeshanhirani - who's book by the way is amazing! dynamic result; if (invoice.PropertyInvoices is EntityCollection<PropertyInvoice>) result = (invoices.PropertyInvoices as EntityCollection<PropertyInvoice>).CreateSourceQuery().Yadda.Yadda.Yadda else //must be a unit test! result = invoices.PropertyInvoices; return result.ToList(); EDIT2: Ok, I just realized that you can't dispatch extension methods whilst using dynamic. So I guess we're not quite as dynamic as Ruby, but the example above is easily modifiable to comport with this restriction EDIT3: As mentioned in zeeshanhirani's blog post, this only works if (and only if) you have change-enabled proxies, which will get created if all of your properties are declared virtual. Here's another version of what the method might look like to use CreateSourceQuery with POCOs public class Person { public virtual int ID { get; set; } public virtual string FName { get; set; } public virtual string LName { get; set; } public virtual double Weight { get; set; } public virtual ICollection<Book> Books { get; set; } } public class Book { public virtual int ID { get; set; } public virtual string Title { get; set; } public virtual int Pages { get; set; } public virtual int OwnerID { get; set; } public virtual ICollection<Genre> Genres { get; set; } public virtual Person Owner { get; set; } } public class Genre { public virtual int ID { get; set; } public virtual string Name { get; set; } public virtual Genre ParentGenre { get; set; } public virtual ICollection<Book> Books { get; set; } } public class BookContext : DbContext { public void PrimeBooksCollectionToIncludeGenres(Person P) { if (P.Books is EntityCollection<Book>) (P.Books as EntityCollection<Book>).CreateSourceQuery().Include(b => b.Genres).ToList(); }

    Read the article

  • I can connect to Samba server but cannot access shares.

    - by jlego
    I'm having trouble getting samba sharing working to access shares. I have setup a stand-alone box running Fedora 16 to use as a file-sharing and web development server. It needs to be able to share files with a Windows 7 PC and a Mac running OSX Snow Leopard. I've setup Samba using the Samba configuration GUI tool on Fedora. Added users to Fedora and connected them as Samba users (which are the same as the Windows and Mac usernames and passwords). The workgroup name is the same as the Windows workgroup. Authentication is set to User. I've allowed Samba and Samba client through the firewall and set the ethernet to a trusted port in the firewall. Both the Windows and Mac machines can connect to the server and view the shares, however when trying to access the shares, Windows throws error: 0x80070035 " Windows cannot access \\SERVERNAME\ShareName." Windows user is not prompted for a username or password when accessing the server (found under "Network Places"). This also happens when connecting with the IP rather than the server name. The Mac can also connect to the server and see the shares but when choosing a share gives the error: The original item for ShareName cannot be found. When connecting via IP, the Mac user is prompted for username and password, which when authenticated gives a list of shares, however when choosing a share to connect to, the error is displayed and the user cannot access the share. Since both machines are acting similarly when trying to access the shares, I assume it is an issue with how Samba is configured. smb.conf: [global] workgroup = workgroup server string = Server log file = /var/log/samba/log.%m max log size = 50 security = user load printers = yes cups options = raw printcap name = lpstat printing = cups [homes] comment = Home Directories browseable = no writable = yes [printers] comment = All Printers path = /var/spool/samba browseable = yes printable = yes [FileServ] comment = FileShare path = /media/FileServ read only = no browseable = yes valid users = user1, user2 [webdev] comment = Web development path = /var/www/html/webdev read only = no browseable = yes valid users = user1 How do I get samba sharing working? UPDATE: I Figured it out, it was because I was sharing a second hard drive. See checked answer below. Speculation 1: Before this box I had another box with the same version of fedora installed (16) and samba working for these same computers. I started up the old machine and copied the smb.conf file from the old machine to the new one (editing the share definitions for the new shares of course) and I still get the same errors on both client machines. The only difference in environment is the hardware and the router. On the old machine the router received a dynamic public IP and assigned dynamic private IPs to each device on the network while the new machine is connected to a router that has a static public IP (still dynamic internal IPs though.) Could either one of these be affecting Samba? Speculation 2: As the directory I am trying to share is actually an entire internal disk, I have tried these things: 1.) changing the owner of the mounted disk from root to my user (which is the same username as on the Windows machine) 2.) made a share that only included one of the folders on the disk instead of the entire disk with my user again as the owner. Both tests failed giving me the same errors regarding the network address. Speculation 3: Whenever I try to connect to the share on the Windows 7 client I am prompted for my username and password. When I enter the correct credentials I get an access denied message. However I did notice that under the login box "domain: WINDOWS-PC-NAME" is listed. I believe this could very well be the problem. Speculation 4: So I've completely reinstalled Fedora and Samba now. I've created a share on the first harddrive (one fedora is installed on) and I can access that fine from Windows. However when I try to share any data on the second disk, I am receiving the same error. This I believe is the problem. I think I need to change some things in fstab or fdisk or something. Speculation 5: So in fstab I mapped the drive to automount in a folder which works correctly. I also added the samba_share_t SElinux label to the mountpoint directory which now allows me to access the shares on the Windows machine, however I cannot see any of the files in the directory on the windows machine. (They are there, I can see them in the fedora file browser locally)

    Read the article

  • How to select table column names in a view and pass to controller in rails?

    - by zachd1_618
    So I am new to Rails, and OO programming in general. I have some grasp of the MVC architecture. My goal is to make a (nearly) completely dynamic plug-and-play plotting web server. I am fairly confused with params, forms, and select helpers. What I want to do is use Rails drop downs to basically pass parameters as strings to my controller, which will use the params to select certain column data from my database and plot it dynamically. I have the latter part of the task working, but I can't seem to pass values from my view to controller. For simplicity's sake, say my database schema looks like this: --------------Plot--------------- |____x____|____y1____|____y2____| | 1 | 1 | 1 | | 2 | 2 | 4 | | 3 | 3 | 9 | | 4 | 4 | 16 | | 5 | 5 | 25 | ... and in my Model, I have dynamic selector scopes that will let me select just certain columns of data: in Plot.rb class Plot < ActiveRecord::Base scope :select_var, lambda {|varname| select(varname)} scope :between_x, lambda {|x1,x2| where("x BETWEEN ? and ?","#{x1}","#{x2}")} So this way, I can call: irb>>@p1 = Plot.select_var(['x','y1']).between_x(1,3) and get in return a class where @p1.x and @p1.y1 are my only attributes, only for values between x=1 to x=4, which I dynamically plot. I want to start off in a view (plot/index), where I can dynamically select which variable names (table column names), and which rows from the database to fetch and plot. The problem is, most select helpers don't seem to work with columns in the database, only rows. So to select columns, I first get an array of column names that exist in my database with a function I wrote. Plots Controller def index d=Plot.first @tags = d.list_vars end So @tags = ['x','y1','y2'] Then in my plot/index.html.erb I try to use a drop down to select wich variables I send back to the controller. index.html.erb <%= select_tag( :variable, options_for_select(@plots.first.list_vars,:name,:multiple=>:true) )%> <%= button_to 'Plot now!', :controller =>"plots/plot_vars", :variable => params[:variable]%> Finally, in the controller again Plots controller ... def plot_vars @plot_data=Plot.select_vars([params[:variable]]) end The problem is everytime I try this (or one of a hundred variations thereof), the params[:variable] is nill. How can I use a drop down to pass a parameter with string variable names to the controller? Sorry its so long, I have been struggling with this for about a month now. :-( I think my biggest problem is that this setup doesn't really match the Rails architecture. I don't have "users" and "articles" as individual entities. I really have a data structure, not a data object. Trying to work with the structure in terms of data object speak is not necessarily the easiest thing to do I think. For background: My actual database has about 250 columns and a couple million rows, and they get changed and modified from time to time. I know I can make the database smarter, but its not worth it on my end. I work at a scientific institute where there are a ton of projects with databases just like this. Each one has a web developer that spends months setting up a web interface and their own janky plotting setups. I want to make this completely dynamic, as a plug-and-play solution so all you have to do is specify your database connection, and this rails setup will automatically show and plot which data you want in it. I am more of a sequential programmer and number cruncher, as are many people here. I think this project could be very helpful in the end, but its difficult to figure out for me right now.

    Read the article

< Previous Page | 215 216 217 218 219 220 221 222 223 224 225 226  | Next Page >