Search Results

Search found 54116 results on 2165 pages for 'application restart'.

Page 22/2165 | < Previous Page | 18 19 20 21 22 23 24 25 26 27 28 29  | Next Page >

  • Apache restart on Ubuntu - error “could not bind to address 0.0.0.0:80”

    - by william
    I'm a n00b - trying to get apache2 set up on Ubuntu 9.10 (Karmic Koala) on Rackspace Cloud. I have set up/configured OpenSSL and installed Apache, but Apache won't start. I assume its a misconfiguration in my /etc/apache2/sites-available/ssl or /etc/apache2/sites-available/default files) When I try to restart apache using the command: sudo /etc/init.d/apache2 restart I get the following error message: [error] (EAI 2)Name or service not known: Could not resolve host name *.80 -- ignoring! [error] (EAI 2)Name or service not known: Could not resolve host name *.80 -- ignoring! (98)Address already in use: make_sock: could not bind to address 0.0.0.0:80 no listening sockets available, shutting down Unable to open logs ...fail! For my /etc/apache2/sites-available/ssl I have used a virtual host of *:443. For my /etc/apache2/sites-available/default i have used a virtual host of *:80

    Read the article

  • Location of Opera cookies set to expire after restart (time 0)

    - by marc
    Where does Opera store cookies that are destroyed or expire after the browser is restarted? I'm looking for information on where these temporary cookies, with time expire (0), and that are deleted after a browser restart. I tested a file "cookies4.dat" using a hex editor and it doesn't have the temporary cookies stored inside. Does Opera create a temporary file for these cookies and delete them after restart? If that was so, where are they? Or does it store them in RAM?

    Read the article

  • Windows 7 won't restart with SSD

    - by JL
    I have this annoying problem that I just can't seem to fix. Recently I upgraded my main boot drive to an OCZ Vertex Turbo (60GB) which is an SSD. I've installed Windows 7 64bit. The drive works, and is really quick... blah blah blah. My problem is when I do a restart, for example click start, then arrow next to shutdown, and restart. The computer will shut down, and do a warm reboot, but it gets stuck where it says loading Windows. Just before the animation starts. So what I have to do is physically press the reset switch on the computer, then it restarts, firing up a menu which offers to launch Windows Startup Repair, so I select "Start Windows Normally". After this I boot in normally, but its damn annoying. Any ideas why this is happening, what I can do to fix it?

    Read the article

  • Make puppet agent restart itself

    - by SamKrieg
    I've got a file that notifies the puppet agent. In the network module, the proxy settings are included in the .gemrc file like this: file { "/root/.gemrc": content => "http_proxy: $http_proxy\n", notify => Service['puppet'], } The problem is that puppet stops and does not restart. Aug 31 12:05:13 snch7log01 puppet-agent[1117]: (/Stage[main]/Network/File[/root/.gemrc]/content) content changed '{md5}2b00042f7481c7b056c4b410d28f33cf' to '{md5}60b725f10c9c85c70d97880dfe8191b3' Aug 31 12:05:13 snch7log01 puppet-agent[1117]: Caught TERM; calling stop I assume the code does something like /etc/init.d/puppet stop && /etc/init.d/puppet start Since puppet is not running, it cannot start itself... it kind of makes sense. How to make puppet restart itself when this file changes? Note that this file may not exist as well.

    Read the article

  • Unable to load type error in ASP.NET 4 application on Windows Server 2003 / IIS6 -- only happens after first worker process recycle

    - by Daniel Coffman
    I'm running an ASP.NET 4.0 web application on IIS6 (Windows Server 2003 x64). This app is one of many running on this server under the Default Web Site -- but is alone on it's own application pool because the other sites are all running ASP.NET 2.0 still. When I deploy my application, it works just fine until the application pool recycles or kills its worker process (by default 2 hours or 20 minutes with no activity). After this, I get the error: "Unable to load one or more of the requested types. Retrieve the LoaderExceptions property for more information. System.Reflection.ReflectionTypeLoadException: Unable to load one or more of the requested types. Retrieve the LoaderExceptions property for more information." Refreshing the page, recycling the application pool, and iisreset do nothing. But, I can bring the site back online again for a little while by simply redeploying it. The stack trace seems to start at an EntityDataSource -- see below: [ReflectionTypeLoadException: Unable to load one or more of the requested types. Retrieve the LoaderExceptions property for more information.] System.Reflection.RuntimeModule.GetTypes(RuntimeModule module) +0 System.Reflection.Assembly.GetTypes() +144 System.Data.Metadata.Edm.ObjectItemConventionAssemblyLoader.LoadTypesFromAssembly() +45 System.Data.Metadata.Edm.ObjectItemAssemblyLoader.Load() +34 System.Data.Metadata.Edm.AssemblyCache.LoadAssembly(Assembly assembly, Boolean loadReferencedAssemblies, ObjectItemLoadingSessionData loadingData) +130 System.Data.Metadata.Edm.AssemblyCache.LoadAssembly(Assembly assembly, Boolean loadReferencedAssemblies, KnownAssembliesSet knownAssemblies, EdmItemCollection edmItemCollection, Action`1 logLoadMessage, Object& loaderCookie, Dictionary`2& typesInLoading, List`1& errors) +248 System.Data.Metadata.Edm.ObjectItemCollection.LoadAssemblyFromCache(ObjectItemCollection objectItemCollection, Assembly assembly, Boolean loadReferencedAssemblies, EdmItemCollection edmItemCollection, Action`1 logLoadMessage) +580 System.Data.Metadata.Edm.ObjectItemCollection.ExplicitLoadFromAssembly(Assembly assembly, EdmItemCollection edmItemCollection, Action`1 logLoadMessage) +193 System.Data.Metadata.Edm.MetadataWorkspace.ExplicitLoadFromAssembly(Assembly assembly, ObjectItemCollection collection, Action`1 logLoadMessage) +140 System.Web.UI.WebControls.EntityDataSourceView.ConstructContext() +756 System.Web.UI.WebControls.EntityDataSourceView.ExecuteSelect(DataSourceSelectArguments arguments) +147 This is a bug filed for the same (or similar) problem: http://connect.microsoft.com/VisualStudio/feedback/details/541962/unable-to-load-one-or-more-of-the-requested-types-connected-with-entitydatasource Question: Has anyone seen this and have advice? I've tried copy-local on all the references... Works just fine on my dev machine. Works on the server until the application pool worker process recycles. I'm building in release mode, but experience the same result when I build for debug. I'm stumped.

    Read the article

  • OS2/Warp - Remotely Stop and Restart a Program

    - by Justin S
    Our current phone system runs off of a legacy OS2/Warp box. Periodically we have to log into the machine and restart OS2RSD.exe and then start it again and the phone system starts working again. The problem is we have to physically get in front of the box and use the GUI to stop and restart the process. Is it possibly to remotely run a script to kill OS2RSD.exe if its running and then start it again? I have been unable to figure this out on my own. The OS is OS2/Warp Version 3 if that helps.

    Read the article

  • Windows 7 unload driver/disconnect usb before restart

    - by brux
    In xp, my Tascam US 122 usb audio interface works fine. On my windows 7 computer the device works, however when i restart/shutdown it hangs at the "shutting down" screen forever. If the usb cable is removed prior to initiating restart/shutdown then everything goes fine, the computer restarts as normal. This is a known problem, running any other driver in compatibility mode doesnt fix the problem. Is there a method I can use to unload the device/drivers so that I dont have to reach round physically and disconnect the cable. Somebody suggested a spdt switch on the cable itself, but I am looking for a simpler method. Surely I can automate the unloading of the device through a script or such? Any ideas are greatly welcomed thanks

    Read the article

  • How to "restart/repair" an USB port?

    - by Click Ok
    My laptop have 2 usb ports, but one is broken, so I use an USB hub in the another good USB port. In that USB hub, I use a mouse and keyboard. Suddenly, that USB port doesn't detects the mouse and keyboard (even with the light of the hub is on), and the only solution that I found is restarting the laptop. But just some minutes and the keyboard and mouse goes undetected again... So, I wonder if there is some method/software/etc to "restart/repair" the USB port without restart the PC. Thanks for all!

    Read the article

  • Unable to change IP address for eth0 without restart in Ubuntu

    - by Rodnower
    I have Ubuntu 12.04.1 installed. I tried to change the IP address of the interface eth0 in /etc/network/interfaces from 192.168.1.3 to 192.168.1.4 auto lo iface lo inet loopback pre-up iptables-restore < /etc/iptables.up.rules auto eth0 iface eth0 inet static address 192.168.1.4 gateway 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 sudo service networking status When I issue: sudo service networking restart I get this response: stop: Unknown instance: networking stop/waiting And IP remains 192.168.1.3: eth0 Link encap:Ethernet HWaddr 00:1e:33:71:cd:a4 inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21e:33ff:fe71:cda4/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3861 errors:0 dropped:0 overruns:0 frame:0 TX packets:3291 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3423285 (3.4 MB) TX bytes:521854 (521.8 KB) Interrupt:45 Base address:0x4000 Only after restart does the IP change. Any ideas?

    Read the article

  • Unable chage IP address for eth0 without restart in Ubunto

    - by Rodnower
    I have Ubuntu 12.04.1 installed. I try to change IP address of the interface eth0 in /etc/network/interfaces from 192.168.1.3 to 192.168.1.4: auto lo iface lo inet loopback pre-up iptables-restore < /etc/iptables.up.rules auto eth0 iface eth0 inet static address 192.168.1.4 gateway 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 sudo service networking status Now I issue: sudo service networking restart I have response: stop: Unknown instance: networking stop/waiting And IP remains 192.168.1.3: eth0 Link encap:Ethernet HWaddr 00:1e:33:71:cd:a4 inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21e:33ff:fe71:cda4/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3861 errors:0 dropped:0 overruns:0 frame:0 TX packets:3291 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3423285 (3.4 MB) TX bytes:521854 (521.8 KB) Interrupt:45 Base address:0x4000 Only after restart IP changing... Any ideas?

    Read the article

  • mysqld stopped working..can't restart...need help?

    - by grant tailor
    i was just checking somethings and noticed mysqld is not running in parallels power panel control panel...but my websites on the server were all working fine, which use mysql databases...so really strange So i tried to restart mysqld but got errors and can't restart and now all my websites are all offline now saying error connecting to database. logged in as root and tried /etc/init.d/mysqld start and got this error ERROR! Manager of pid-file quit without updating file What do i do next? What do i do? Please help!

    Read the article

  • Linux: how to verify my network configuration before doing a restart

    - by wael34218
    I am trying to build a network bridge for my VMs on a server. So I added a new file and changed another in the /etc/sysconfig/network-scripts directory. Then I did a network reboot with the following command:/etc/init.d/network restart After that the server was not up again. I contacted the hosting provider's support for help. I need a way to verify my new configuration before a network restart. I need to make sure that it will be up again, just like apache's /etc/init.d/httpd configtest

    Read the article

  • Group policy reset upon restart?

    - by sc_ray
    Is it possible for a group policy to revert back to its original state upon server restart? Our servers are hosted as a Virtual Machine on the rack. We had to restart our server for some reason and all of a sudden we cannot remote desktop into the server any more. Pinging the server succeeds but RDPing into it fails. My assumption is that the group policy has reverted back preventing any remote desktop connections from taking place. Is that a possibility? Since the network is managed by another group, we don't have the authority to physically look into what's going on with this particular VM. Can somebody suggest some ideas? Thanks

    Read the article

  • Remote Desktop AND monitor fail on restart (Win2008R2)

    - by Wesley
    I am in the process of building a small 3 server farm. Each machine is running Window Server 2008 R2. As is normal, I am in the process of installing patch after patch to bring the machine up to snuff. Every time I restart the machine, or most every time, when I try to remote in to the machine I get the Log In window, but then almost immediately I get the message that my remote session was ended. If I physically walk over to the machine and plug in a monitor and keyboard, I see nothing. If I leave the keyboard and monitor in and restart the machine by force, the computer reboots just fine. When windows starts, I get no error message about windows not starting or being shut off unexpectedly. Once I log into the machine physically by the keyboard, I can then remote in to the machine at that point. Very confused. This happens on all 3 machines, these machines have different hardware.

    Read the article

  • Auto restart server if virtual memory is too low

    - by Sukhjinder Singh
    There are quite number of software running on my server: httpd, varnish, mysql, memcache, java.. Each of them is using a part of the virtual memory and varnish was configured to be allocated 3GB of memory to run. Due to high traffic load which is 100K, our server ran out of memory and oom-killer is invoked. We've to reboot the server. We have 8GB of Virtual Memory and due to some reason we cannot extend to larger memory. My question is - Is there any automated script, which will monitor how much virtual memory left and based upon certain criteria, lets say if 500MB left than restart the server automatically? I do know this is not the proper solution but we have to do it, otherwise we don't know when server will get OOM and by the time we know and restart the server, we lost our visiting users.

    Read the article

  • HttpUtility.UrlEncode in console application

    - by iar
    I'd like to use HttpUtility.UrlEncode in a console application, VB.NET, VS 2010 Beta 2. System.Web.HttpUtility.UrlEncode(item) Error message: 'HttpUtility' is not a member of 'Web'. In this question Anjisan suggests to add a reference to System.Web, as follows: In your solution explorer, right click on references Choose "add reference" In the "Add Reference" dialog box, use the .NET tab Scroll down to System.Web, select that, and hit ok However, I don't have a System.Web entry at that location.

    Read the article

  • Blackberry Menu from native blackberry application

    - by chrishawn
    I have an application that inserts an ApplicationMenuItem into the native blackberry contacts menu. I can get this to work just fine. Now my question is how would I change or remove that ApplicationMenuItem based on the contact that i am highlighted on? Would I need to use a GlobalEventListener? I assume overriding makeMenu can only be done for menus on my own screens and not the native contacts screen?

    Read the article

  • Changing startup object of console application at runtime

    - by MicMit
    Assuming I've got several unrelated classes in separate files with a main method in each. Currently project is a console application and I just change a startup object in IDE to run respective main which instantiates respective class from IDE. Out of curiosity would it be possible to change the startup object dynamically at runtime somehow before launching this exe as an alternative of having this project as a class library and repeating code which I have in main(s) somewhere else.

    Read the article

  • Input event loop in a console application

    - by Álvaro
    Hi, I'm trying to make a little console application that is able to deal with keystrokes as events. What I need is mostly the ability to get the keystrokes and be able to do something with them without dealing with the typical stdin reading functions. I tried to check the code of programs like mplayer, which implement this (for stopping the play, for example), but I can't get to the core of this with such a big code base. Thanks

    Read the article

  • Relative connection string to AzMan XML store when using security application block

    - by David Hall
    Is it possible to specify a relative connection string for an AzMan XML store? My current connection string is connectionString="msxml://c:/azman.xml" but I really need to make that relative so other developers and automated builds can get the latest authorization store. MS documentation seems to suggest that connectionString="msxml://azman.xml" should work but that throws a The request is not supported error. EDIT: I realised that the fact I'm using AzMan through the Enterprise Library Security Application Block was important to the question.

    Read the article

< Previous Page | 18 19 20 21 22 23 24 25 26 27 28 29  | Next Page >