Search Results

Search found 1148 results on 46 pages for 'capacity'.

Page 22/46 | < Previous Page | 18 19 20 21 22 23 24 25 26 27 28 29  | Next Page >

• Optimal Memory Configuration for Dell PowerEdge 1800 (Windows Server 2000 32bit)

  - by David Murdoch

  I am upgrading the memory on a Dell PowerEdge 1800 Server running Windows Server 2000 (32 bit). My Computer Properties currently reports "2,096,432 KB RAM" (4 modules @ 512MB each). Crucial.com scan reports: "Each memory slot can hold DDR2 PC2-5300 with a maximum of 2GB per slot. Maximum Memory Capacity:  12288MB Currently Installed Memory:  2GB Available Memory Slots:  2 Total Memory Slots:  6 Dual Channel Support:   No CPU Manufacturer:  GenuineIntel CPU Family:  Intel(R) Xeon(TM) CPU 2.80GHz Model 4, Stepping 1 CPU Speed:  2793 MHz Installed in pairs of modules." We will be completely replacing the old 512 MB modules. Will there be any performance difference between installing 4 modules @ 1GB vs. 2 modules @ 2GB?

  Read the article

• Resize Ubuntu Linux system to smaller disk inside VMware ESXi

  - by mlambie

  I have several Ubuntu Linux virtual machines running on VMware ESXi hosts that have all been allocated disks much larger than their required capacity. As space is now becoming an issue on our SAN, I'd like to investigate downsizing the allocated disk space on these machines. All systems will be completely backed up imaged before I begin making changes, and I will always retain a pristine backup in case the partition resizing does not work. Is there an easier way than the following procedure, or is their a better solution entirely? Shutdown and assign a second disk to the virtual machine Boot using the SystemRescueCD Use GParted to resize the original (source) partition, making it smaller Clone the new, smaller partition to the second disk Shutdown and remove initial disk from the virtual machine Reboot and force fsck to check the filesystem

  Read the article

• Optimising bare-metal hypervisor installation

  - by Stephen

  what is the best way to install a bare metal hypervisor (i.e. to host multiple VM's)? I spoke to a friend and he is using a HP server to host all his VMs with VMware ESXi, but he installed the VMWARE esxi software on a flash card. He can then use his full hard disk capacity from each drive for the VMs. Is this a pretty standard setup when configuring a bare-metal hypervisor? How do you guys do it, and what is best?

  Read the article

• How do I make more available space on a Time Machine hard disk?

  - by Daryl Spitzer

  I upgraded my MacBook Pro to Snow Leopard, and made some other changes that have caused my next Time Machine backup to be quite large. Previous to the upgrade my backup drive had filled up, so Time Machine was deleting old backups to make room for new ones. When Time Machine started the first backup after the upgrade, it displayed a message that it was freeing up space. But it wasn't able to free up enough: (The disk has 320 GB capacity.) How can I free up more space on the disk (without reformatting or deleting all the existing backups)? I don't want to recklessly delete files and take the risk of confusing Time Machine.

  Read the article

• Mountable online storage (no syncing)

  - by Sam

  I have a Linux VPS that I would like to turn into a media server. Like most cheap VPS's, it has a fairly small storage capacity. What I would like to do is attach the box to an online backup system such as SpiderOak or DropBox, where the files would reside and be directly accessible to either a webserver or media server software. Since the VPS hdd is small, I do not want the files to be synced to it. I would like a storage system that is online only. Ideally mountable like a network drive. Are there any services that suit my needs, or workarounds for services such as SpiderOak that do not require syncing?

  Read the article

• Photo Management Software for OS X That Supports Multiple Library Locations

  - by Lance Rushing

  I'm looking at the possibility of changing our photo management software. Thinking about Aperture or Lightroom. And want to know if either supports: Having folders/libraries on separate harddrives/Volumes. Tolerates having network folders occasionally connected Snappy interface A solid enough piece of software as not to crash or behave weirdly. [ so the wife doesn't get stuck and have to call me ;) ] Background The wife is photographer and I'm the computer programmer. Our current setup is Picasa, with a "Recent/Working" folder on the local iMac harddrive, and "Archive" folders on NFS mounted Linux Server, Raid 5, for redundant and extra storage capacity. (the Linux server also syncs with Amazon's EC2) Picasa is doing OK, but I get annoyed when it doesn't do behave properly. Usually around issues when the Linux disk isn't mounted. And overall, I wish Picasa seemed a little more polished and snappier. Thanks, Lance

  Read the article

• What is better to have more LUNs or more Storages

  - by skomak

  Hi, what is better to have - more LUNs or more Storages. Actually i have 1 storage ESXi per 1 LUN so there are about 15 LUNs and 15 storages. Now there is a kind of problem because the LUNs have different space allocated so if i remove 2 LUNs f.e. 1 2 3 4 [x] 6 [x] 8 9 (like that) i can't make 1 LUN from 5 and 7 pieces of free diskspace on IBM storage array. It's a first argument to not have a lot of LUNs. If i had to make only a few LUNs (about 3) and inside some Storage from ESXi would it be a better idea? For example for expanding storage capacity? i look for good solutions. Thanks in advance.

  Read the article

• Alternative to WMP for mp3 player sync

  - by Dan Neely

  I've been using WMP to sync to my Creative Zen since I bought it a year ago. It worked fine when my collection was still smaller than its capacity, but that's no longer the case, and I can't find any way to specify which music should be synced/not synced. WMP's sync by alphabetical order is an unacceptable option. What I think I want is something that would show my collection organized by artist/album/song (with file size info) in a treeview with checkboxes that saves my selections so I just have make adjustments as needed with new albums instead of having to rebuild my list from scratch every time.

  Read the article

• Linux software raid robustness for raid1 vs other raid levels

  - by Waxhead

  I have a raid5 running and now also a raid1 that I set up yesterday. Since raid5 calculates parity it should be able to catch silent data corruption on one disk. However for raid1 the disks are just mirrors. The more I think about it I figure that raid1 is actually quite risky. Sure it will save me from a disk failure but i might not be as good when it comes to protecting the data on disk (who is actually more important for me). How does Linux software raid actually store raid1 type data on disk? How does it know what spindle is giving corrupt data (if the disk(subsystem) is not reporting any errors) If raid1 really is not giving me data protection but rather disk protection is there some tricks I can do with mdadm to create a two disk "raid5 like" setup? e.g. loose capacity but still keep redundancy also for data!?

  Read the article

• Intel cpu hyperthreading on or off for ibm db2?

  - by rtorti19

  Has anyone ever done any database performance comparisons with hyper-threading enabled vs disabled? We are running ibm db2 and I'm curious if anyone has an recommendations for enabling hyper-threading or not. With hyper-threading enabled it makes it quite difficult to do capacity planning for cpu usage. For example. "With 8 physical cores represented as 16 "threads" on the OS and a cpu-bound workload, does that mean when your cpu usage hit's 50% you are actually running at 100%." What real benefits do I gain with leaving hyper-threading enabled on an intel server running DB2? Does hyper-threading help if you're workload is truly disk IO bound? If so, up to what percentage? These are the types of questions I'm trying to answer. Any thoughts?

  Read the article

• How can I log all traffic with its exact length?

  - by Legate

  I want to process all packets with their size going through our gateway server (running Debian 4.0). My idea is to use tcpdump, but I have two questions. The command I'm currently thinking of is tcpdump -i iface -n -t -q. Is it guaranteed that tcpdump will process all packets? What happens if the CPU is working to full capacity? The format of the output lines is IP ddd.ddd.ddd.ddd.port > ddd.ddd.ddd.ddd.port: tcp 1260. What exactly is 1260? I have the suspicion that it is the payload in bytes of the packet, which would be exactly what I need, but I'm not sure. It might be the TCP Window Size. Or perhaps there is an even better way of doing this? I thought about a LOG rule in iptables, but tcpdump seems easier and I don't know whether iptables can log the packet lengths.

  Read the article

• (Open Source) Cloud-Filesystem to run a Database on Top?

  - by jens

  Hello, what are current "technologies and implementations" to get a filesystem with unlimited capacity by using single servers with their harddisk to form a "grid/cloud filesystem"? I need to have unlimited space (by adding further servers) but it must be a filesysem that is capable of running a database on top. I know of Apache Hadoop but that seems not be be Ideal for running a DB on top of it (or am I wrong??) And iSCSI seems to be "remote/networked" but I do not know how and if this is clusterable? thank you very much!! jens

  Read the article

• (Open Source) Cloud-Filesystem to run a Database on Top?

  - by jens

  Hello, what are current "technologies and implementations" to get a filesystem with unlimited capacity by using single servers with their harddisk to form a "grid/cloud filesystem"? I need to have unlimited space (by adding further servers) but it must be a filesysem that is capable of running a database on top. I know of Apache Hadoop but that seems not be be Ideal for running a DB on top of it (or am I wrong??) And iSCSI seems to be "remote/networked" but I do not know how and if this is clusterable? thank you very much!! jens

  Read the article

• What are the quality metrics for RAM?

  - by Hi-Tech KitKat Android

  I have searched RAM and i found there are given some specification for the same capacity RAM, What are the difference and performance comparison between these? Like RAM1 General Brand Transcend Memory Type 2 GB (8 x 128 MB) DDR2 DIMM Memory Standard DDR2-800/PC-6400 Compatible Device PC Pins 240-pin Burst Length 4, 8 Buffered/Unbuffered Unbuffered Memory Memory Clock 400 MHz Technology DDR2 SDRAM Memory CAS Latency 4, 5, 6 RAM 2 General Brand Transcend Memory Type 2 GB (8 x 128 MB) DDR2 DIMM Memory Standard DDR2-667/PC2-5300 Compatible Device PC Pins 240-pin Burst Length 4, 8 Buffered/Unbuffered Unbuffered Memory Memory Clock 333 MHz Technology DDR2 SDRAM Memory CAS Latency 3, 4, 5 RAM3 General Brand Kingston Memory Type 2 GB (64 x 256 MB) 800 MHz DDR2 DIMM Compatible Device PC Pins 240-pin Error Check Non-ECC Buffered/Unbuffered Unbuffered Memory Memory Clock 200 MHz Technology DDR2 SDRAM Memory CAS Latency 6 What are the affect of the following Memory Type(given as 8 x 128 MB) Memory Clock (given in MHz) CAS Latency (given as 4,5,6) my Requirement is 2 GB DDR2 Type Desktop Please help

  Read the article

• Wireless technology - which is better: more single radio APs or less dual radio APs?

  - by gert_78

  We are currently talking to vendors of wireless solutions for a wireless deployment in a university campus with some 5000 students. One vendor is offering us a Cisco solution with a WLC 5508 controller and 69 2x2 MIMO Dual-band/Dual radio APs (Aironet AP 1042 model) The other vendor is offering us an Aruba solution with a 3600 controller and 96 2x2 MIMO dual band BUT single radio APs (Aruba AP93) Both vendors are charging 82.000 US$ (support, 3y service contracts, switches and additional required options all included of course) The Aruba vendor is trying to convince me that 96 single radio APs will give us more connection/users/capacity then the 69 dual radio APs. I have my doubts about that and since it is my core competence-domain I wanted to ask here the opinion of people that have a more profound knowledge and experience in this area. When you talk to vendors it's often hard to get objective information. So try to answer only if you are sure and please mention it if you are affiliated with one of the vendors. I appreciate all useful help and want to thank you in advance for the effort!

  Read the article

• Linear Performance Scalability with HP San Solutions

  - by Berzemus

  Hi all, I need a San Solution with linear scalability in size as well as in performance. From what I know, with a Modular Smart Array solution such as the P2000/MSA-class solutions from HP, even with a dual controller initial node, I can only increase the size of it, as added nodes come controller-less, so overall performance tends to decrease. On the other hand, the P4000 (lefthand) family of solutions has each of it's nodes have it's own controller, and so when a node is added, storage capacity as well as performance increase. Am I right in all that I say, and is the P4000 the only solution, or have I forgotten something ?

  Read the article

• Postfix Inbound/Outbound Gateway for Google Apps

  - by geofflee

  I currently have a Postfix/Dovecot setup, but our server is hitting capacity, so we decided to switch to Google Apps. However, we have certain web applications that need to send and receive e-mail directly (for example, e-mail being redirected to a script). What I want to do is host certain e-mail accounts with Google Apps, while my current server continues to manage other e-mail accounts. I assume this means that I would use my current server as an Inbound/Outbound Gateway, so my questions are: 1) How do I setup Postfix as an Outbound Gateway without making it an (insecure) open relay? 2) How do I setup Postfix as an Inbound Gateway so that only certain e-mail addresses are forwarded to Google Apps? Thank you!

  Read the article

• MacBook says to replace battery. Should I?

  - by Palantir

  Hi! My MacBook says that battery is not charging, and the battery is completely empty (in fact, pressing the button on the battery illuminates no LEDs). If I plug the power adapter off the mac shuts off immediately. I tried with a spare adapter, and it won't charge it. System information says it has 380 cycles. The battery is 2.5 years old. System profiler says the battery has 0 mAh of capacity, and that it should be replaced. Should I just buy a new battery, or should I bring it to an apple point, and leave it there? They can take a look at it (it's on AppleCare), they told me that they will repair it is there is anything wrong with the charging circuit, but they won't give me a new battery. They will keep the laptop for 10 working days at least... I hate when this happens :P

  Read the article

• Why does 1GBit card have output limited to 80 MiB ?

  - by Gallus

  I'm trying to utilize maximal bandwidth provided by my 1GiB network card, but it's always limited to 80MiB (real megabytes). What can be the reason? Card description (lshw output): description: Ethernet interface product: DGE-530T Gigabit Ethernet Adapter (rev 11) vendor: D-Link System Inc physical id: 0 bus info: pci@0000:03:00.0 logical name: eth1 version: 11 serial: 00:22:b0:68:70:41 size: 1GB/s capacity: 1GB/s width: 32 bits clock: 66MHz capabilities: pm vpd bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation The card is placed in following PCI slot: *-pci:2 description: PCI bridge product: 82801 PCI Bridge vendor: Intel Corporation physical id: 1e bus info: pci@0000:00:1e.0 version: 92 width: 32 bits clock: 33MHz capabilities: pci subtractive_decode bus_master cap_list The PCI isn't any PCI Express right? It's a legacy PCI slot? So maybe this is the reason? OS is a linux.

  Read the article

• AMD FX 8350 potentially overheating

  - by rhughes

  I am worried that my CPU is overheating when running at maximum capacity. I have not overclocked the machine. The machine often powers down after a couple of minutes of max CPU usage. I get the following events in the Event Log after the crash: Log Name: System Source: Microsoft-Windows-Kernel-Power Date: 11/10/2013 12:05:40 Event ID: 41 Task Category: (63) Level: Critical Keywords: (2) User: SYSTEM Computer: home-pc Description: The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. What can I do to confirm this or further narrow down this issue? Due to the sudden nature of the crash, no MEMORY.DMP is created I believe. I am happy to post any extra information that is needed.

  Read the article

• Volume size doesn't match Disk size after gparted expansion

  - by Cybersylum

  I just expanded a basic disk on a Windows XP VM from 15gb to 40 gb using GPARTED LiveCD (0.5.2-11). I didn't notice anything unusual during the expansion; but after I rebooted back into Windows, the disk capacity doesn't match the disk size as it should (only 1 volume on the disk). The disk shows as 40gb; but the C: volume still shows the original size. I've tried expanding the disk again with GPARTED (no change), and using VMware converter and have it adjust the size of the volume during the process (complains about a lack of space of snapshot error inside the os). The volume has 27% free space so I don't think it is a space issue. Chkdsk doesn't seem to find anything wrong either. The OS seems to run just fine, it doesn't see the additional space however. Any ideas?

  Read the article

• Choosing A Power Supply [closed]

  - by Geeks On Hugs

  Possible Duplicate: Power Supply Capacity Formula How can I check if my system needs more PSU power? I'm not sure if it's OK or not to ask a hardware question here. If not please let me know a good place but I've always got good info here so I thought I'd give it a shot. I'm custom building a new workstation for coding (Linux/Eclipse). How do I determine how much power the power supply needs? I'm building a mini ITX system on a budget and so I need to get as small as possible that is sufficient. I'll have a mini itx mobo with on board wifi and bluetooth, 8 GB RAM, an Intel i3 3.1 Ghz processor, 64 GB SSD and a slim optical drive. In the future I might add a descrete GPU, 16 GB RAM, 128 GB SSD. What is the minimum power I need and how do I calculate that?

  Read the article

• Massive amount of subfolders and long subfolders. ¿How can I delete all of them?

  - by Carlos

  Good day. We have a little problem here. We have a share with the backup of all the server's offices, Its a really big share with more than 8.000.000 files. Our users usually give long names to the folders they create, and then make subfolders (long too) and more subfolders... and more suboflders.... We have a new share with more capacity, and with a simpe robocopy bat we copied all the files and folders (some give problems, but we manually copied them) But the problem is deleting them. del command didnt work well when so long paths, neirder rmdir... I'm tried some commanders, but no luck. Can u recommend me any tool that can delete recursively or able to delete 255+ paths? Edited: The SO on background of the share it's NetApp OS. But I can access it from Windows Servers. 2000 and 2003 Thanks.

  Read the article

• Count total file size of many files in Windows

  - by user105249

  When I want to burn a CD R with lots of files, I have to make sure the total file size in my folder doesn't exceed the capacity of the disc (680MB). In Windows are there possibilities to check the total file size of a bunch of files. I put them in a folder, right-click and check the properties. But this is an annoying trial and error kind of way. Either there are too many files in the folder, or too little. I watch the file size go up as I keep selecting more files, using ALT+going down button. No. 2 is my favorite way to do it. Here's my question: For some reason Windows (I still use XP) only shows the total file size of 100 selected files. When you select more than 100 files, no file size information appears any more. Is there way, a trick, an app, to work around this problem?

  Read the article

• Windows server 2008 UPS support

  - by Rory McCune

  I'm looking to set-up a UPS on a Windows Small Business Berver 2k8 and I've noticed that there are some large price differences for similar capacity in-line UPSs. The most important point for me in UPS selection is that the server should have the ability to shut itself down before the UPS power runs out, so that if the server is unattended during the outage, it should minimize the risk of data loss. From some reading it appears that Windows Server 2008 should has the ability to natively recognise a UPS, which can then be managed through the battery settings on the server or via WMI. What I'm wondering if anyone know is, Is Windows 2008 servers UPS support specific to certain brands of UPS (eg, APC) or is it likely to work with any UPS which has a USB port, which I can connect to the server?

  Read the article

< Previous Page | 18 19 20 21 22 23 24 25 26 27 28 29  | Next Page >