Search Results

Search found 592 results on 24 pages for 'lspci'.

Page 22/24 | < Previous Page | 18 19 20 21 22 23 24  | Next Page >

• trying to setup wireless

  - by JohnMerlino

  I'm trying to set up wireless on vostro 1520 dell laptop, with latest Ubuntu install. Here's the output of some of the commands that I was told to run: lshw -C network viggy@ubuntu:~$ lshw -C network WARNING: you should run this program as super-user. *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: 03 serial: 00:24:e8:da:84:25 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168d-1.fw ip=192.168.2.6 latency=0 multicast=yes port=MII speed=100Mbit/s resources: irq:47 ioport:3000(size=256) memory:f6004000-f6004fff memory:f6000000-f6003fff memory:f6020000-f603ffff *-network description: Network controller product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:0e:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:18 memory:fa000000-fa003fff *-network DISABLED description: Wireless interface physical id: 1 logical name: wlan0 serial: 0c:60:76:05:ee:74 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.2.0-29-generic firmware=N/A multicast=yes wireless=IEEE 802.11bg lspci 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) 00:1c.2 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) 00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 03) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) 0e:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) 1a:00.0 FireWire (IEEE 1394): O2 Micro, Inc. Device 10f7 (rev 01) 1a:00.1 SD Host controller: O2 Micro, Inc. Device 8120 (rev 01) 1a:00.2 Mass storage controller: O2 Micro, Inc. Device 8130 (rev 01) iwconfig lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on eth0 no wireless extensions. At this point in time, I don't have wireless.

  Read the article

• Upgraded to 12.04 now wifi doesn't work

  - by Benito Kestelman

  My laptop's wifi stopped working when I upgraded to Ubuntu 12.04 (wired works). I just reinstalled 12.04 over my old 12.04 on which wifi didn't work either in an attempt to restore any settings I may have accidentally changed, but it still doesn't work. I also used a wired connection to install updates in case this bug has been fixed, but it has not. Here is the result of sudo lshw -class network: *-network description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 67 serial: 40:25:c2:5f:5b:f4 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-29-generic-pae firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:51 memory:de800000-de801fff *-network description: Ethernet interface product: AR8151 v2.0 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c0 serial: 14:da:e9:c0:da:78 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:54 memory:dd400000-dd43ffff ioport:a000(size=128) Here is rfkill list all: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: asus-wimax: WiMAX Soft blocked: no Hard blocked: no lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 8087:07d6 Intel Corp. Bus 001 Device 004: ID 13d3:5710 IMC Networks Bus 002 Device 003: ID 045e:0745 Microsoft Corp. Nano Transceiver v1.0 for Bluetooth Bus 003 Device 003: ID 0781:5530 SanDisk Corp. Cruzer lspci: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1c.5 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 6 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 02:00.0 Network controller: Intel Corporation Centrino Wireless-N + WiMAX 6150 (rev 67) 03:00.0 USB controller: ASMedia Technology Inc. ASM1042 SuperSpeed USB Host Controller 04:00.0 Ethernet controller: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet (rev c0)

  Read the article

• Drivers for Atheros AR928X?

  - by Pato7

  I am new in Ubuntu and I had a big trouble with wifi. My ubuntu 12.10 doesn't detect my wifi card and I can't toggle the "activate wireless" option on the tasks bar (it is grey). I searched for drivers to make it work, but nothing worked for me. Can anyone give me a hand? Many thanks in advanced! lspci output 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) 00:1c.2 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RV710 [Mobility Radeon HD 4500/5100 Series] 01:00.1 Audio device: Advanced Micro Devices [AMD] nee ATI RV710/730 HDMI Audio [Radeon HD 4000 series] 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8057 PCI-E Gigabit Ethernet Controller (rev 10) 03:00.0 Network controller: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) (rev 01) 0c:03.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 05) 0c:03.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22) 0c:03.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 12) lshw -c network output *-network descripción: Ethernet interface producto: 88E8057 PCI-E Gigabit Ethernet Controller fabricante: Marvell Technology Group Ltd. id físico: 0 información del bus: pci@0000:02:00.0 nombre lógico: eth0 versión: 10 serie: 00:24:be:83:b2:4f tamaño: 100Mbit/s capacidad: 1Gbit/s anchura: 64 bits reloj: 33MHz capacidades: pm msi pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuración: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.30 duplex=full ip=192.168.1.123 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s recursos: irq:45 memoria:d3520000-d3523fff ioport:c000(size=256) memoria:d3500000-d351ffff *-network DESACTIVADO descripción: Interfaz inalámbrica producto: AR928X Wireless Network Adapter (PCI-Express) fabricante: Atheros Communications Inc. id físico: 0 información del bus: pci@0000:03:00.0 nombre lógico: wlan0 versión: 01 serie: 2c:81:58:e6:b6:03 anchura: 64 bits reloj: 33MHz capacidades: pm msi pciexpress msix bus_master cap_list ethernet physical wireless configuración: broadcast=yes driver=ath9k driverversion=3.5.0-18-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn recursos: irq:17 memoria:d2100000-d210ffff rfkill list all output 0: phy0: Wireless LAN Soft blocked: yes Hard blocked: yes 1: sony-wifi: Wireless LAN Soft blocked: yes Hard blocked: no

  Read the article

• Wireless connection works but the internet is too slow to use in Ubuntu 11.04

  - by Garrin

  The internet is so slow as to be unusable. And I'm not being picky. Even after minutes I can't get my Google home page to load. I tried installing a package through apt-get and was getting rates between 0 and a few hundred bytes/s. That's bytes, not kilobytes! Mostly 0 however (no exaggeration, it spends large amounts of time stalled). And I would go to a speed test web site of some kind but I can't since nothing will load. Briefly put, the laptop I am using was connected to two wireless networks while using Ubuntu 11.04 without any issues before this. It was also connected to a wired network without any issues. It dual boats Windows 7 which has never had any issues, not even with the current wireless network. Just to be clear, on the current wi-fi network, Windows 7 encounters no issues (speedtest.net puts the network speed at 1mb/s) but my network connection in Ubuntu 11.04 is so slow as to literally be unusable. I am unfamiliar with the router except for the fact that it boasts a Rogers logo (that's a large ISP/cable provider in Canada for those not familiar with the land of igloos and polar bears). I am far from the router and some desktop widget I use tells me the signal strength is at 58% (it seems fairly reliable and this would appear to match up with the filled bars in the network icon). I should also mention I'm just renting a room in this house so I'm not the network administrator and while I can access the 192.168.0.1 router page, the password wasn't set to 'password' so it's not much use to me. Here are a bunch of commands I ran which don't tell me a whole lot but I thought might be more instructive to the wise around here: lspci (just showing my network card): 05:00.0 Network controller: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) (rev 01) This one is self explanatory. PING www.googele.com (216.65.41.185) 56(84) bytes of data. 64 bytes from nnw.net (216.65.41.185): icmp_req=1 ttl=51 time=267 ms 64 bytes from nnw.net (216.65.41.185): icmp_req=2 ttl=51 time=190 ms 64 bytes from nnw.net (216.65.41.185): icmp_req=3 ttl=51 time=212 ms 64 bytes from nnw.net (216.65.41.185): icmp_req=4 ttl=51 time=207 ms 64 bytes from nnw.net (216.65.41.185): icmp_req=5 ttl=51 time=220 ms --- www.googele.com ping statistics --- 5 packets transmitted, 5 received, 0% packet loss, time 4003ms rtt min/avg/max/mdev = 190.079/219.699/267.963/26.121 ms ifconfig eth0 Link encap:Ethernet HWaddr 20:6a:8a:02:20:da UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:42 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:16 errors:0 dropped:0 overruns:0 frame:0 TX packets:16 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:960 (960.0 B) TX bytes:960 (960.0 B) wlan0 Link encap:Ethernet HWaddr 20:7c:8f:05:c6:bf inet addr:192.168.0.16 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::227c:8fff:fe05:c6bf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:982 errors:0 dropped:0 overruns:0 frame:0 TX packets:658 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:497250 (497.2 KB) TX bytes:95076 (95.0 KB) Thank you

  Read the article

• Ubuntu 12.10 no network and no graphics

  - by khasiKoMasu

  I recently upgraded Ubuntu 12.04 to 12.10 only to find out that it won't connect to any network, neither wired nor wireless and the graphics is messed up too as in a low screen resolution. For 12.04, my system was running perfectly. I don't know why upgrade messed it up so bad. Reinstalling the OS is an issue because I have set up a lot of development environments that I cannot afford to set it up again. Some of the outputs: lspci -nn | grep 0200 02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 02) nm-tool NetworkManager Tool State: disconnected cat /etc/network/interfaces auto lo iface lo inet loopback sudo cat /var/log/syslog | grep etwork | tail -n20 Nov 2 13:50:22 Cobalt NetworkManager[978]: SCPlugin-Ifupdown: (-1240454760) ... get_connections (managed=false): return empty list. Nov 2 13:50:22 Cobalt NetworkManager[978]: Ifupdown: get unmanaged devices count: 0 Nov 2 13:50:22 Cobalt bluetoothd[1016]: Failed to init network plugin Nov 2 13:50:22 Cobalt NetworkManager[978]: <info> modem-manager is now available Nov 2 13:50:22 Cobalt NetworkManager[978]: <info> monitoring kernel firmware directory '/lib/firmware'. Nov 2 13:50:22 Cobalt NetworkManager[978]: <info> WiFi enabled by radio killswitch; enabled by state file Nov 2 13:50:22 Cobalt NetworkManager[978]: <info> WWAN enabled by radio killswitch; enabled by state file Nov 2 13:50:22 Cobalt NetworkManager[978]: <info> WiMAX enabled by radio killswitch; enabled by state file Nov 2 13:50:22 Cobalt NetworkManager[978]: <info> Networking is enabled by state file Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> /sys/devices/virtual/net/lo: couldn't determine device driver; ignoring... Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> /sys/devices/virtual/net/lo: couldn't determine device driver; ignoring... Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> bluez error getting default adapter: Message did not receive a reply (timeout by message bus) Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> bluez error getting default adapter: Message did not receive a reply (timeout by message bus) Nov 2 13:50:22 Cobalt kernel: [ 28.688167] type=1400 audit(1351882222.452:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1046 comm="apparmor_parser" Nov 2 13:50:22 Cobalt bluetoothd[1062]: Failed to init network plugin Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> bluez error getting default adapter: Message did not receive a reply (timeout by message bus) Nov 2 13:50:22 Cobalt bluetoothd[1118]: Failed to init network plugin Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> bluez error getting default adapter: Message did not receive a reply (timeout by message bus) Nov 2 13:50:22 Cobalt bluetoothd[1237]: Failed to init network plugin Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> bluez error getting default adapter: Message did not receive a reply (timeout by message bus) ps aux | grep -i network root 978 0.0 0.1 23732 4808 ? Ssl 13:50 0:00 NetworkManager sudo modprobe -r forcedeth FATAL: Module forcedeth not found

  Read the article

• ubuntu 10.04: wlan0 No such device

  - by AodhanOL

  I am using a Dell xps l702x and I am using ubuntu 10.04 because I need to use f77 (don't ask) and I wasn't able to get it working on later versions of ubuntu. I cannot use the wifi at all. I have tried to fix it and have had limited success (changed the output from rfkill list all from Hard blocked: yes, to hard blocked: no). Here is the output from rfkill list all aodhan@aodhan-laptop:~$ rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 2: dell-bluetooth: Bluetooth Soft blocked: no Hard blocked: no Here is the output from iwconfig: aodhan@aodhan-laptop:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions. pan0 no wireless extensions. And here is the output from ifconfig -a: aodhan@aodhan-laptop:~$ ifconfig -a eth0 Link encap:Ethernet HWaddr 5c:f9:dd:3d:f2:f7 inet addr:192.168.1.17 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::5ef9:ddff:fe3d:f2f7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3417 errors:0 dropped:0 overruns:0 frame:0 TX packets:2894 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3317567 (3.3 MB) TX bytes:505049 (505.0 KB) Interrupt:30 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) pan0 Link encap:Ethernet HWaddr 7e:7e:e8:39:70:af BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) And finally, the output from lspci: 00:00.0 Host bridge: Intel Corporation Device 0104 (rev 09) 00:01.0 PCI bridge: Intel Corporation Sandy Bridge PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Device 0116 (rev 09) 00:16.0 Communication controller: Intel Corporation Cougar Point HECI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation Cougar Point High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 2 (rev b5) 00:1c.3 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 4 (rev b5) 00:1c.4 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 5 (rev b5) 00:1c.5 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 6 (rev b5) 00:1d.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation Device 1c4b (rev 05) 00:1f.2 SATA controller: Intel Corporation Cougar Point 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation Cougar Point SMBus Controller (rev 05) 01:00.0 VGA compatible controller: nVidia Corporation Device 1246 (rev a1) 03:00.0 Network controller: Intel Corporation Device 008a (rev 34) 04:00.0 USB Controller: NEC Corporation Device 0194 (rev 04) 0a:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) Please help me! Thank you in advance. Edit: Further info - this is a dual install with a windows 7 system as the other option. However, I can't access that until tomorrow (I won't have access to the windows 7 disc until then, and grub isn't letting me load it). Therefore, I can't be sure whether it still works on that or not. It used to, though.

  Read the article

• iSCSI timeouts under high load

  - by Antonio

  I have two servers connected via Gigabit Ethernet. One is iSCSI target, the second one is initiator. When I run mkfs.ext4 at initiator, after a while disk IO slows down critically. In the target host I can see the following in syslog: Sep 14 09:40:03 sh11 tgtd: abort_task_set(1139) found 119668c 0 Sep 14 09:40:03 sh11 tgtd: abort_cmd(1115) found 119668c 6 Sep 14 09:40:03 sh11 tgtd: abort_task_set(1139) found 119668d 0 Sep 14 09:40:03 sh11 tgtd: abort_cmd(1115) found 119668d 6 Sep 14 09:40:03 sh11 tgtd: abort_task_set(1139) found 119668e 0 Sep 14 09:40:03 sh11 tgtd: abort_cmd(1115) found 119668e 6 Sep 14 09:40:03 sh11 tgtd: abort_task_set(1139) found 1196696 0 Sep 14 09:40:03 sh11 tgtd: abort_cmd(1115) found 1196696 6 Sep 14 09:40:03 sh11 tgtd: abort_task_set(1139) found 119669e 0 Sep 14 09:40:03 sh11 tgtd: abort_cmd(1115) found 119669e 6 Sep 14 09:40:04 sh11 tgtd: abort_task_set(1139) found 119669f 0 Sep 14 09:40:04 sh11 tgtd: abort_cmd(1115) found 119669f 6 And load average grows to 12 or even more: # uptime 12:37:00 up 23 days, 13:25, 1 user, load average: 12.00, 7.00, 4.00 CentOS 6.3 tgtd 1.0.24 Intel Pentium 4 2.4GHz 1Gb RAM 2Tb WD Cavlar Green SATA 2.0 #lspci 00:00.0 Host bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE DRAM Controller/Host-Hub Interface (rev 02) 00:01.0 PCI bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE Host-to-AGP Bridge (rev 02) 00:1d.0 USB controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 02) 00:1d.1 USB controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 02) 00:1d.2 USB controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 02) 00:1d.7 USB controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 82) 00:1f.0 ISA bridge: Intel Corporation 82801DB/DBL (ICH4/ICH4-L) LPC Interface Bridge (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801DB (ICH4) IDE Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 02) 00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 02) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RV200 QW [Radeon 7500] 02:01.0 Ethernet controller: D-Link System Inc DGE-530T Gigabit Ethernet Adapter (rev 11) (rev 11) 02:02.0 RAID bus controller: VIA Technologies, Inc. VT6421 IDE/SATA Controller (rev 50) 02:03.0 RAID bus controller: VIA Technologies, Inc. VT6421 IDE/SATA Controller (rev 50) 02:04.0 RAID bus controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02) 02:08.0 Ethernet controller: Intel Corporation 82801DB PRO/100 VE (CNR) Ethernet Controller (rev 82) Is there a way to tune target host to avoid these timeouts?

  Read the article

• Attach radeon driver to specific PCI devices?

  - by genpfault

  I have two Radeon cards in this machine, a 6570 and a 6950: lspci | grep VGA: 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Turks [Radeon HD 6570] 02:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Cayman PRO [Radeon HD 6950] I'm trying to get VGA passthrough to work with KVM on Debian Wheezy, passing through the 6950 as a secondary video card to a Windows 7 guest. This works fine if I blacklist the radeon kernel module via /etc/modprobe.d/. If I remove the blacklist to run X11 (or even just a KMS console) on the 6570 the radeon module seems to attach to both cards: dmesg | egrep "01:00.0|02:00.0|radeon": pci 0000:01:00.0: [1002:6759] type 0 class 0x000300 pci 0000:01:00.0: reg 10: [mem 0xe0000000-0xefffffff 64bit pref] pci 0000:01:00.0: reg 18: [mem 0xf7e20000-0xf7e3ffff 64bit] pci 0000:01:00.0: reg 20: [io 0xe000-0xe0ff] pci 0000:01:00.0: reg 30: [mem 0xf7e00000-0xf7e1ffff pref] pci 0000:01:00.0: supports D1 D2 pci 0000:02:00.0: [1002:6719] type 0 class 0x000300 pci 0000:02:00.0: reg 10: [mem 0xd0000000-0xdfffffff 64bit pref] pci 0000:02:00.0: reg 18: [mem 0xf7d20000-0xf7d3ffff 64bit] pci 0000:02:00.0: reg 20: [io 0xd000-0xd0ff] pci 0000:02:00.0: reg 30: [mem 0xf7d00000-0xf7d1ffff pref] pci 0000:02:00.0: supports D1 D2 vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none vgaarb: device added: PCI:0000:02:00.0,decodes=io+mem,owns=none,locks=none vgaarb: bridge control possible 0000:02:00.0 vgaarb: bridge control possible 0000:01:00.0 pci 0000:01:00.0: Boot video device [drm] radeon kernel modesetting enabled. radeon 0000:01:00.0: setting latency timer to 64 radeon 0000:01:00.0: VRAM: 1024M 0x0000000000000000 - 0x000000003FFFFFFF (1024M used) radeon 0000:01:00.0: GTT: 512M 0x0000000040000000 - 0x000000005FFFFFFF [drm] radeon: 1024M of VRAM memory ready [drm] radeon: 512M of GTT memory ready. radeon 0000:01:00.0: irq 46 for MSI/MSI-X radeon 0000:01:00.0: radeon: using MSI. [drm] radeon: irq initialized. radeon 0000:01:00.0: WB enabled [drm] radeon: ib pool ready. [drm] radeon: power management initialized fbcon: radeondrmfb (fb0) is primary device fb0: radeondrmfb frame buffer device [drm] Initialized radeon 2.12.0 20080528 for 0000:01:00.0 on minor 0 radeon 0000:02:00.0: enabling device (0000 -> 0003) radeon 0000:02:00.0: setting latency timer to 64 radeon 0000:02:00.0: VRAM: 2048M 0x0000000000000000 - 0x000000007FFFFFFF (2048M used) radeon 0000:02:00.0: GTT: 512M 0x0000000080000000 - 0x000000009FFFFFFF [drm] radeon: 2048M of VRAM memory ready [drm] radeon: 512M of GTT memory ready. radeon 0000:02:00.0: irq 49 for MSI/MSI-X radeon 0000:02:00.0: radeon: using MSI. [drm] radeon: irq initialized. radeon 0000:02:00.0: WB enabled [drm] radeon: ib pool ready. [drm] radeon: power management initialized fb1: radeondrmfb frame buffer device [drm] Initialized radeon 2.12.0 20080528 for 0000:02:00.0 on minor 1 [drm] radeon: finishing device. radeon 0000:02:00.0: ffff88041a941800 unpin not necessary [drm] radeon: ttm finalized pci-stub 0000:02:00.0: claimed by stub pci-stub 0000:02:00.0: irq 49 for MSI/MSI-X This causes the Win7 VM to bluescreen on boot. How can I configure things so that the radeon module only attaches to the 6570 and not the 6950?

  Read the article

• PSTN Trunk TDM400P Install on Asterisk / Trixbox

  - by Jona

  Hey All, I'm trying to get a TDM400P card with FXO module to connect to our PSTN line. The card is correctly detected by Linux: [trixbox1.localdomain asterisk]# lspci 00:09.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface And asterisk can see the channel: > trixbox1*CLI> dahdi show channel 1 > Channel: 1LI> File Descriptor: 14 > Span: 11*CLI> Extension: I> Dialing: > noI> Context: from-pstn Caller ID: I> > Calling TON: 0 Caller ID name: > Mailbox: none Destroy: 0LI> InAlarm: > 1LI> Signalling Type: FXS Kewlstart > Radio: 0*CLI> Owner: <None> Real: > <None>> Callwait: <None> Threeway: > <None> Confno: -1LI> Propagated > Conference: -1 Real in conference: 0 > DSP: no1*CLI> Busy Detection: no TDD: > no1*CLI> Relax DTMF: no > Dialing/CallwaitCAS: 0/0 Default law: > ulaw Fax Handled: no Pulse phone: no > DND: no1*CLI> Echo Cancellation: > trixbox1128 taps trixbox1(unless TDM > bridged) currently OFF Actual > Confinfo: Num/0, Mode/0x0000 Actual > Confmute: No > Hookstate (FXS only): Onhook I have configured a "ZAP Trunk (DAHDI compatibility Mode)" with the ZAP identifier 1 and an outbound route, but when ever I try to make an external call via it I get the "All Circuits are busy now, please try your call again later message". The FXO module is directly connected to our phone line from BT via a BT-RJ11 cable. I'm guessing I've missed a configuration step somewhere but no idea where, any help greatly appreciated.

  Read the article

• Linux Mint 14 severe overheating

  - by agvares

  I've tried switching to Mint (it was Mint 12) about 6 months ago, but failed to do it due to enormous overheating which made it virtually impossible to run any applications more complex than Gedit. Time had passed, and now I'm back again with Mint 14, but feeling way more determined. What I face are the following issues: 1) Great overheating (and by great I mean that just by doing nothing my CPU temp is floating around 70-75 C, which I find a lot) 2) Running multiple applications (let's say Chrome, Skype and Pidgin) results in critical overheating and immediate shutdown of the system 3) Due to the stuff listed above, my battery drains in about 10-15 minutes, pretty much turning my laptop into a crippled desktop machine I've got a HP-dv6 laptop (i7, 6gb RAM, dual graphics) Here's the output of lspci: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Whistler XT [AMD Radeon HD 6700M Series] 07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) 0d:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) 13:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5209 PCI Express Card Reader (rev 01) 19:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) what i've tried to do already: 1) I've edited my grub file to add some "splash" arguments there 2) Installed jupiter and powertop 3) Tried to upgrade to newer kernels (up to 3.8), btw running anything newer than 3.5 results in both resolution and wi-fi detection fail 4) Read lots of forum threads devoted to the topic So, my question is simple: What else might I do to become finally able to use Mint as my default OS without the risk of being burned alive by the CPU heat?

  Read the article

• Clonezilla restore from Samba - no 'restoredisk' option

  - by MT_Head

  I used a CloneZilla LiveCD to back up a couple of Windows machines to a Samba share. Now I'm trying to restore those images, and CloneZilla won't even give me the 'restoredisk' or 'restorepart' options on the menu. I'm guessing that this is because CZ isn't recognizing a valid image... but why? Here's a listing of the folder on the Samba share: -rwxrwxrwx 1 marc users 319 May 31 03:45 blkdev.list -rwxrwxrwx 1 marc users 5307 May 31 04:41 clonezilla-img -rwxrwxrwx 1 marc users 4 May 31 04:31 disk -rwxrwxrwx 1 marc users 16091 May 31 04:31 Info-dmi.txt -rwxrwxrwx 1 marc users 11029 May 31 04:31 Info-lshw.txt -rwxrwxrwx 1 marc users 1502 May 31 04:31 Info-lspci.txt -rwxrwxrwx 1 marc users 170 May 31 04:31 Info-packages.txt -rwxrwxrwx 1 marc users 80 May 31 04:41 Info-saved-by-cmd.txt -rwxrwxrwx 1 marc users 10 May 31 04:31 parts -rwxrwxrwx 1 marc users 2097152000 May 31 04:06 sda1.ntfs-ptcl-img.gz.aa -rwxrwxrwx 1 marc users 247361656 May 31 04:08 sda1.ntfs-ptcl-img.gz.ab -rwxrwxrwx 1 marc users 823182034 May 31 04:31 sda2.ntfs-ptcl-img.gz.aa -rwxrwxrwx 1 marc users 36 May 31 03:45 sda-chs.sf -rwxrwxrwx 1 marc users 31744 May 31 03:45 sda-hidden-data-after-mbr -rwxrwxrwx 1 marc users 512 May 31 03:45 sda-mbr -rwxrwxrwx 1 marc users 315 May 31 03:45 sda-pt.parted -rwxrwxrwx 1 marc users 285 May 31 03:45 sda-pt.parted.compact -rwxrwxrwx 1 marc users 259 May 31 03:45 sda-pt.sf (I've been experimenting with various permissions trying to get this to work; that's why they're currently all "rwxrwxrwx"...) I've got my CZ LiveCD stuck in a (different) machine with a 160GB SATA disk that I'm fine with overwriting; although CZ doesn't show a directory listing, it does show that the correct folder is mounted as /home/partimag. But a moment later, after selecting either Beginner or Expert, I'm only presented with the "savedisk", "saveparts", and "exit" options. What am I doing wrong? I am confident that the initial backup was successful; I can post the log if desired, or any other information that might be germane. Edit: I've copied the contents of the folder onto a 16GB USB stick and set THAT as /home/partimag. Still nothing. What the hell is CZ looking for?

  Read the article

• Why are the analoge stereo input and output of my M-Audio 24/96 soundcard not available to me in Ubu

  - by user37968

  I have installed Lucid on an old Mac PowerPC G4 desktop with a M-Audio Audiophile 24/96 soundcard. The only inputs and outputs I can select in the audio preferences are digital ones for the digital input and output. "lspci -v" shows the card as so: 0001:10:13.0 Multimedia audio controller: VIA Technologies Inc. ICE1712 [Envy24] PCI Multi-Channel I/O Controller (rev 02) Subsystem: VIA Technologies Inc. Device d634 Flags: bus master, medium devsel, latency 16, IRQ 53 I/O ports at 0440 [size=32] I/O ports at 04b0 [size=16] I/O ports at 04a0 [size=16] I/O ports at 0400 [size=64] Capabilities: <access denied> Kernel driver in use: ICE1712 Kernel modules: snd-ice1712 "cat /proc/asound/cards" as so: 0 [Tumbler ]: PMac Tumbler - PowerMac Tumbler PowerMac Tumbler (Dev 21) Sub-frame 0 1 [M2496 ]: ICE1712 - M Audio Audiophile 24/96 M Audio Audiophile 24/96 at 0x440, irq 53 "aplay -L" shows these as listed: pulse Playback/recording through the PulseAudio sound server front:CARD=Tumbler,DEV=0 PowerMac Tumbler, PowerMac Tumbler Front speakers front:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi Front speakers surround40:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 4.0 Surround output to Front and Rear speakers surround41:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 5.1 Surround output to Front, Center, Rear and Subwoofer speakers iec958:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi IEC958 (S/PDIF) Digital Audio Output I believe it is a problem with detecting the analogue input/output. Sometimes I can get sound from the device but it is a sheet of white noise and tinkering makes it go away again I don't know if that is a separate problem or if it is linked to not being able to see the analogue input/outputs in the sound preferences. Any help would be greatly appreciated As for the white noise I have installed the Envy24 control panel and spend lots of time playing with the settings but when I can get the white noise I can never get it to an quality where I can actually hear what is being played. The internal speaker plays audio fine and plugging in a NI Audio 4DJ via usb also plays sound, although with some static but I believe that is due to an underpowered usb2 pci expansion card not being able to get enough electricity to the device. Alternatively I have seen other people with problems with this device so it may be a bug in the driver but that is another matter. I would like to get the M-Audio card working so I can begin to enjoy my music once again. As a note, I do not currently have any audio equipment capable of sending or receiving audio via the digital inputs and output so I can not check if they are working. The sound preferences show a wide range of digital in and out options with various surround sound options but no analogue ins and outs.

  Read the article

• Why are the analoge stereo input and output of my M-Audio 24/96 soundcard not available to me in Ubuntu Lucid

  - by MIDoubleKO

  I have installed Lucid on an old Mac PowerPC G4 desktop with a M-Audio Audiophile 24/96 soundcard. The only inputs and outputs I can select in the audio preferences are digital ones for the digital input and output. "lspci -v" shows the card as so: 0001:10:13.0 Multimedia audio controller: VIA Technologies Inc. ICE1712 [Envy24] PCI Multi-Channel I/O Controller (rev 02) Subsystem: VIA Technologies Inc. Device d634 Flags: bus master, medium devsel, latency 16, IRQ 53 I/O ports at 0440 [size=32] I/O ports at 04b0 [size=16] I/O ports at 04a0 [size=16] I/O ports at 0400 [size=64] Capabilities: <access denied> Kernel driver in use: ICE1712 Kernel modules: snd-ice1712 "cat /proc/asound/cards" as so: 0 [Tumbler ]: PMac Tumbler - PowerMac Tumbler PowerMac Tumbler (Dev 21) Sub-frame 0 1 [M2496 ]: ICE1712 - M Audio Audiophile 24/96 M Audio Audiophile 24/96 at 0x440, irq 53 "aplay -L" shows these as listed: pulse Playback/recording through the PulseAudio sound server front:CARD=Tumbler,DEV=0 PowerMac Tumbler, PowerMac Tumbler Front speakers front:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi Front speakers surround40:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 4.0 Surround output to Front and Rear speakers surround41:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 5.1 Surround output to Front, Center, Rear and Subwoofer speakers iec958:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi IEC958 (S/PDIF) Digital Audio Output I believe it is a problem with detecting the analogue input/output. Sometimes I can get sound from the device but it is a sheet of white noise and tinkering makes it go away again I don't know if that is a separate problem or if it is linked to not being able to see the analogue input/outputs in the sound preferences. Any help would be greatly appreciated As for the white noise I have installed the Envy24 control panel and spend lots of time playing with the settings but when I can get the white noise I can never get it to an quality where I can actually hear what is being played. The internal speaker plays audio fine and plugging in a NI Audio 4DJ via usb also plays sound, although with some static but I believe that is due to an underpowered usb2 pci expansion card not being able to get enough electricity to the device. Alternatively I have seen other people with problems with this device so it may be a bug in the driver but that is another matter. I would like to get the M-Audio card working so I can begin to enjoy my music once again. As a note, I do not currently have any audio equipment capable of sending or receiving audio via the digital inputs and output so I can not check if they are working. The sound preferences show a wide range of digital in and out options with various surround sound options but no analogue ins and outs.

  Read the article

• file corruption on read/write 2.6.32-22-server (happens across many kernels)

  - by Jonathan

  Hi Guys, I'm having an issue where after the server has been up for a period of time (~week/few days) the server will start reading corrupt data. For instance when I run a sha1sum of a file after a fresh boot it remains the same. However after a while I will start to get segfaults and from then on whenever I read this file I get a different sha1sum. I've checked S.M.A.R.T with long tests and I've run an extended memtest86+(12 passes) My lspci is as follows: 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge 00:01.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (int gfx) 00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) 00:07.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 3) 00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] 00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:12.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:12.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:13.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:13.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3c) 00:14.1 IDE interface: ATI Technologies Inc SB700/SB800 IDE Controller 00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:14.5 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 01:05.0 VGA compatible controller: ATI Technologies Inc Radeon HD 3300 Graphics 01:05.1 Audio device: ATI Technologies Inc RS780 Azalia controller 02:00.0 Ethernet controller: Atheros Communications Atheros AR8121/AR8113/AR8114 PCI-E Ethernet Controller (rev b0) 03:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. Device 3403 I could really use some help on this, do you have any idea what could cause this? It's really frustrating me as it seems to trigger entirely randomly and will not go away until I reboot. I'm also use KVM for virtualization as well as MD for software RAID on this server and the processor is a Phenom II X4 965. I don't believe it's the software raid however as this affects files also hosted on non-raid partitions so I don't know.

  Read the article

• How to install missing Sound Drivers in Ubuntu?

  - by Sakamoto Kazuma

  I seem to be missing drivers for my Gateway laptop MA7. I have looked in System-Admin-Hardware Drivers, but it does not show up in there.There are also no devices listed in Sound-Hardware. I'm guessing at this point that I don't have the driver installed. However, I get the following output: admin@machine001:~$ cat /proc/asound/cards 0 [Intel ]: HDA-Intel - HDA Intel HDA Intel at 0xd8240000 irq 22 admin@machine001:~$ And my lspci shows: 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA AHCI Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8038 PCI-E Fast Ethernet Controller (rev 14) 03:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02) 04:09.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 04:09.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller 04:09.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) I have also checked alsamixer, and nothing is muted. No headphones plugged into headphone jack either. So the question now is, how do I get sound to work on my laptop? It doesn't work for any application.

  Read the article

• graphic error on console

  - by Christian Elsner

  I have Linux on an embedded system. There is no graphic system, but I still have graphic errors. For example, if I type: ifconfig eth2 hw ether 00:0e:8c:d0:59:d2 I see: ifconfig eth hw ether 00:0e:8:2:2 If I type Enter, it accepts the command I typed, so it's just a matter of displaying. Everything is fine, when I log in via SSH. Anyone any ideas, what could be the cause or where to look at? Output of lspci: 00:00.0 Host bridge: Intel Corporation 3100 Chipset Memory I/O Controller Hub 00:00.1 Unassigned class [ff00]: Intel Corporation 3100 DRAM Controller Error Reporting Registers 00:01.0 System peripheral: Intel Corporation 3100 Chipset Enhanced DMA Controller 00:02.0 PCI bridge: Intel Corporation 3100 Chipset PCI Express Port A 00:03.0 PCI bridge: Intel Corporation 3100 Chipset PCI Express Port A1 00:1c.0 PCI bridge: Intel Corporation 631xESB/632xESB/3100 Chipset PCI Express Root Port 1 (rev 01) 00:1c.1 PCI bridge: Intel Corporation 631xESB/632xESB/3100 Chipset PCI Express Root Port 2 (rev 01) 00:1d.0 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #2 (rev 01) 00:1d.7 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset EHCI USB2 Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c9) 00:1f.0 ISA bridge: Intel Corporation 631xESB/632xESB/3100 Chipset LPC Interface Controller (rev 01) 00:1f.2 IDE interface: Intel Corporation 631xESB/632xESB/3100 Chipset SATA IDE Controller (rev 01) 00:1f.3 SMBus: Intel Corporation 631xESB/632xESB/3100 Chipset SMBus Controller (rev 01) 02:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection 03:01.0 Network controller: Siemens Nixdorf AG Device 4003 (rev 02) 03:01.1 Unassigned class [ff00]: Siemens Nixdorf AG Device 4003 (rev 02) 03:02.0 Ethernet controller: Siemens Nixdorf AG Device 4047 (rev 01) 03:03.0 Ethernet controller: National Semiconductor Corporation DP83815 (MacPhyter) Ethernet Controller 03:04.0 Unassigned class [ff00]: Siemens Nixdorf AG Device 4057 (rev 01) 04:00.0 PCI bridge: Texas Instruments XIO2000(A)/XIO2200(A) PCI Express-to-PCI Bridge (rev 03) 05:00.0 Ethernet controller: Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE] (rev 44) 06:00.0 PCI bridge: Texas Instruments XIO2000(A)/XIO2200(A) PCI Express-to-PCI Bridge (rev 03) 07:00.0 VGA compatible controller: Silicon Motion, Inc. SM720 Lynx3DM (rev c1) 07:01.0 USB Controller: NEC Corporation USB (rev 43) 07:01.1 USB Controller: NEC Corporation USB (rev 43) 07:01.2 USB Controller: NEC Corporation USB 2.0 (rev 04) The whole thing is running on an Intel Core 2 Duo U2500

  Read the article

• Ubuntu hardware wireless switch has no effect after suspend and 13.10 upgrade

  - by blaineh

  I'm posting this on SU after it stalled on askubuntu. I hope someone here can help! If you'd prefer to answer on AU itself, here's the link: http://askubuntu.com/questions/365177/hardware-wireless-switch-has-no-effect-after-suspend-and-13-10-upgrade Wireless works fine after a reboot, but after a suspend the hardware switch (for my laptop this is f12) has no effect on the wireless, it is just permanently off, and shows that it is with a red LED. My rfkill list all reads: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Any combination with rfkill <un>block wifi doesn't work, although one time first blocking then unblocking actually turned it on again. sudo lshw -C network reads: *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:65:2e:3f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.11.0-12-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:90100000-9010ffff *-network DISABLED description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 02 serial: c8:0a:a9:89:b4:30 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:90010000-90010fff memory:90000000-9000ffff memory:90020000-9002ffff Also, adding a /etc/pm/sleep.d/brcm.sh file as recommended here simply prevents the laptop from suspending at all, which of course is no good. This question has an answer urging to install the original driver, but it wasn't an "accepted answer" so I'd rather not take a chance on it. Also I'll admit I'm a bit lost on that and would like help doing so with the specific information I've given. I would be happy to provide more information, so long as you're willing to help me find it for you! This is a very annoying bug. I have a Compaq Presario CQ62. Edit. Output of lspci | grep Network: 02:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01) Edit. This morning, I had had the laptop suspended all night, and then when I tried to awake it, it simply wouldn't. It would try, and then it would sleep again (I guess it felt a little bit like me! </badjoke>). Is it possible these problems are related? Edit. I don't have enough reputation on SU proper to post links to pastebins and other questions I've tried, so I'm putting them in comments, and of course they're available in the original question.

  Read the article

• how to setup kismet.conf on Ubuntu

  - by Registered User

  I installed Kismet on my Ubuntu 10.04 machine as apt-get install kismet every thing seems to work fine. but when I launch it I see following error kismet Launching kismet_server: //usr/bin/kismet_server Suid priv-dropping disabled. This may not be secure. No specific sources given to be enabled, all will be enabled. Non-RFMon VAPs will be destroyed on multi-vap interfaces (ie, madwifi-ng) Enabling channel hopping. Enabling channel splitting. NOTICE: Disabling channel hopping, no enabled sources are able to change channel. Source 0 (addme): Opening none source interface none... FATAL: Please configure at least one packet source. Kismet will not function if no packet sources are defined in kismet.conf or on the command line. Please read the README for more information about configuring Kismet. Kismet exiting. Done. I followed this guide http://www.ubuntugeek.com/kismet-an-802-11-wireless-network-detector-sniffer-and-intrusion-detection-system.html#more-1776 how ever in kismet.conf I am not clear with following line source=none,none,addme as to what should I change this to. lspci -vnn shows 0c:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g [14e4:4315] (rev 01) Subsystem: Dell Device [1028:000c] Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f69fc000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number Capabilities: [16c] Power Budgeting <?> Kernel driver in use: wl Kernel modules: wl, ssb and iwconfig shows lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"WIKUCD" Mode:Managed Frequency:2.462 GHz Access Point: <00:43:92:21:H5:09> Bit Rate=11 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Managementmode:All packets received Link Quality=1/5 Signal level=-81 dBm Noise level=-90 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:169 Invalid misc:0 Missed beacon:0 So what should I be putting in place of source=none,none,addme with output I mentioned above ?

  Read the article

• Can not get sound over hdmi in kubuntu 9.10

  - by user32509

  I have used a hdmi cable to connect my lcd (which is connected with my speakers) with my nvida 275 gtx grafic card. I can not get the sound output to work. The hardware itself is working probably - I tested it under windows. Currently I am running Kubuntu 9.10 64 with Nvidia 190.53. The sound output worked fine before I installed the hdmi connection. (German output - i can change it, if you tell me how :)) aplay -l **** Liste von PLAYBACK Geräten **** Karte 0: Intel [HDA Intel], Gerät 0: ALC889A Analog [ALC889A Analog] Untergeordnete Geräte: 1/1 Untergeordnetes Gerät '0: subdevice #0 Karte 0: Intel [HDA Intel], Gerät 1: ALC889A Digital [ALC889A Digital] Untergeordnete Geräte: 1/1 Untergeordnetes Gerät '0: subdevice #0 aplay -L front:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog Front speakers surround40:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 4.0 Surround output to Front and Rear speakers surround41:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 5.1 Surround output to Front, Center, Rear and Subwoofer speakers surround71:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 7.1 Surround output to Front, Center, Side, Rear and Woofer speakers iec958:CARD=Intel,DEV=0 HDA Intel, ALC889A Digital IEC958 (S/PDIF) Digital Audio Output null Discard all samples (playback) or generate zero samples (capture) pulse Playback/recording through the PulseAudio sound server And i disabled mute in kmix an all channels :) Edit: lspci -v ... 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02) Subsystem: Giga-byte Technology Device a022 Flags: bus master, fast devsel, latency 0, IRQ 22 Memory at ea400000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel <?> Capabilities: [130] Root Complex Link <?> Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel ... cat /proc/asound/version Advanced Linux Sound Architecture Driver Version 1.0.20. lsmod | grep snd_hda_intel snd_hda_intel 31880 2 snd_hda_codec 87584 2 snd_hda_codec_realtek,snd_hda_intel snd_pcm 93160 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss snd 77096 16 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device snd_page_alloc 10928 2 snd_hda_intel,snd_pcm I think I am missing the something-hdmi module? Is there such a thing?

  Read the article

• Network unreachable on Ubuntu guest after trying to set up a host only network on Virtualbox

  - by gkb0986

  I have a Mac OS X host and a bunch of guests including Ubuntu and Arch Linux. I was trying to set up a host-only network at eth1 to let me ssh into the system. But now eth0 isn't working properly either. Ubuntu can no longer connect to remote hosts or browse the internet. It tells me that the network is unreachable. What's gone wrong here? I've included some diagnostics below. $ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:10968 errors:0 dropped:0 overruns:0 frame:0 TX packets:10968 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:897264 (897.2 KB) TX bytes:897264 (897.2 KB) Other diagnostic commands and the output: $sudo lspci -n 00:00.0 0600: 8086:1237 (rev 02) 00:01.0 0601: 8086:7000 00:01.1 0101: 8086:7111 (rev 01) 00:02.0 0300: 80ee:beef 00:03.0 0200: 8086:100e (rev 02) 00:04.0 0880: 80ee:cafe 00:05.0 0401: 8086:2415 (rev 01) 00:06.0 0C03: 106B:003F 00:07.0 0680: 8086:7113 (REV 08) 00:0D.0 0106: 8086:2829 (REV 02) $sudo lshw -c network *-network DISABLED description: Ethernet interface product: 82540EM Gigabit Ethernet Controller vendor: Intel Corporation physical id: 3 bus info: pci@0000:00:03.0 logical name: eth0 version: 02 serial: 08:00:27:7d:22:df size: 1Gbit/s capacity: 1Gbit/s width: 32 bits clock: 66MHz capabilities: pm pcix bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000 driverversion=7.3.21-k8-NAPI duplex=full firmware=N/A latency=64 link=no mingnt=255 multicast=yes port=twisted pair speed=1Gbit/s resources: irq:19 memory:f0000000-f001ffff ioport:d010(size=8) $lsmod Module Size Used by nls_utf8 12557 1 isofs 40257 1 vboxsf 43743 2 vesafb 13844 1 snd_intel8x0 38570 2 snd_ac97_codec 134869 1 snd_intel8x0 ac97_bus 12730 1 snd_ac97_codec snd_pcm 97275 2 snd_intel8x0,snd_ac97_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi rfcomm 47604 0 snd_seq 61929 2 snd_seq_midi,snd_seq_midi_event bnep 18281 2 bluetooth 180113 10 rfcomm,bnep ppdev 17113 0 psmouse 97519 0 snd_timer 29990 2 snd_pcm,snd_seq joydev 17693 0 snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq vboxvideo 12622 1 serio_raw 13211 0 snd 79041 11 snd_intel8x0,snd_ac97_codec,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 15091 1 snd vboxguest 235498 7 vboxsf parport_pc 32866 0 drm 241971 2 vboxvideo i2c_piix4 13301 0 snd_page_alloc 18529 2 snd_intel8x0,snd_pcm mac_hid 13253 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp usbhid 47238 0 hid 99636 1 usbhid e1000 108589 0

  Read the article

• Wireless cuts out on Toshiba Satellite S7208

  - by alecRN

  I recently got a Toshiba Satellite L875-S7208 with Windows 7 preinstalled. I installed Ubuntu 12.04 LTS dual boot to the same Windows partition. However, usually 15 minutes or less after booting, the wifi connection dies. Here's some hopefully relevant information: lspci -knn 00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0104] (rev 09) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0116] (rev 09) Subsystem: Toshiba America Info Systems Device [1179:fb40] Kernel driver in use: i915 Kernel modules: i915 00:14.0 USB controller [0c03]: Intel Corporation Panther Point USB xHCI Host Controller [8086:1e31] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: xhci_hcd 00:16.0 Communication controller [0780]: Intel Corporation Panther Point MEI Controller #1 [8086:1e3a] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller [0c03]: Intel Corporation Panther Point USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: ehci_hcd 00:1b.0 Audio device [0403]: Intel Corporation Panther Point High Definition Audio Controller [8086:1e20] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb40] Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge [0604]: Intel Corporation Panther Point PCI Express Root Port 1 [8086:1e10] (rev c4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge [0604]: Intel Corporation Panther Point PCI Express Root Port 2 [8086:1e12] (rev c4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.2 PCI bridge [0604]: Intel Corporation Panther Point PCI Express Root Port 3 [8086:1e14] (rev c4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller [0c03]: Intel Corporation Panther Point USB Enhanced Host Controller #1 [8086:1e26] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge [0601]: Intel Corporation Panther Point LPC Controller [8086:1e59] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel modules: iTCO_wdt 00:1f.2 SATA controller [0106]: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] [8086:1e03] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: ahci 00:1f.3 SMBus [0c05]: Intel Corporation Panther Point SMBus Controller [8086:1e22] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel modules: i2c-i801 02:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) Subsystem: Realtek Semiconductor Co., Ltd. Device [10ec:8211] Kernel driver in use: rtl8192ce Kernel modules: rtl8192ce 03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) Subsystem: Toshiba America Info Systems Device [1179:fb37] Kernel driver in use: r8169 Kernel modules: r8169 lsmod Module Size Used by snd_hda_codec_hdmi 32474 1 snd_hda_codec_realtek 224066 1 joydev 17693 0 rfcomm 47604 0 bnep 18281 2 bluetooth 180104 10 rfcomm,bnep parport_pc 32866 0 ppdev 17113 0 arc4 12529 2 snd_hda_intel 33773 3 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq psmouse 87692 0 serio_raw 13211 0 rtl8192ce 84826 0 rtl8192c_common 75767 1 rtl8192ce rtlwifi 111202 1 rtl8192ce mac80211 506816 3 rtl8192ce,rtl8192c_common,rtlwifi snd 78855 16 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device sparse_keymap 13890 0 uvcvideo 72627 0 videodev 98259 1 uvcvideo v4l2_compat_ioctl32 17128 1 videodev mac_hid 13253 0 mei 41616 0 wmi 19256 0 soundcore 15091 1 snd i915 472941 3 snd_page_alloc 18529 2 snd_hda_intel,snd_pcm drm_kms_helper 46978 1 i915 cfg80211 205544 2 rtlwifi,mac80211 drm 242038 4 i915,drm_kms_helper i2c_algo_bit 13423 1 i915 video 19596 1 i915 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp r8169 62099 0 ums_realtek 18248 0 uas 18180 0 usb_storage 49198 1 ums_realtek dmesg | grep firmware [ 15.692951] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 16.240881] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 452.419288] rtl8192c_common:rtl92c_firmware_selfreset(): 8051 reset fail. [ 458.572211] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 465.440640] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 472.337617] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 479.175471] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 485.978582] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 492.764893] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 499.579348] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 506.386934] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 513.209545] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 519.991365] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 526.778375] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 533.629695] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 540.426004] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 547.238125] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 554.024434] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 560.854794] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 567.678160] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 574.494666] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 581.336653] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 588.157710] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 595.221122] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 602.047429] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 608.829534] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 615.639079] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 622.454991] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 629.273231] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 636.056613] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 642.858096] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 649.640753] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 657.184094] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 664.008018] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 670.838639] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 677.675418] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 684.507255] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 691.310994] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 698.095325] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 704.914509] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 711.725178] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin uname -r 3.2.0-29-generic ifconfig eth0 Link encap:Ethernet HWaddr 4c:72:b9:59:6c:61 inet addr:192.168.0.11 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::4e72:b9ff:fe59:6c61/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4447 errors:0 dropped:0 overruns:0 frame:0 TX packets:2762 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3671147 (3.6 MB) TX bytes:335133 (335.1 KB) Interrupt:42 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:515 errors:0 dropped:0 overruns:0 frame:0 TX packets:515 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:83153 (83.1 KB) TX bytes:83153 (83.1 KB) wlan0 Link encap:Ethernet HWaddr 74:e5:43:32:47:95 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:280 errors:0 dropped:0 overruns:0 frame:0 TX packets:51 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:32958 (32.9 KB) TX bytes:10431 (10.4 KB)

  Read the article

• Dlink DWA-556 Access point fails to start on 2.6.35-25 while 2.6.35-24 works. How can I do this with >2.6.35-24?

  - by Azendale

  I'm using hostapd to run an access point with a Dlink DWA-556 wireless N card. However, I can no longer get it to start when I use kernels greater than 2.6.35-24. Here's a log where I ran the uname -a&&hostapd -c <configfile> on the different kernel versions. Linux erikbandersen 2.6.35-24-generic #42-Ubuntu SMP Thu Dec 2 02:41:37 UTC 2010 x86_64 GNU/Linux Configuration file: hostapd.conf ctrl_interface_group=0 Opening raw packet socket for ifindex 248 BSS count 1, BSSID mask ff:ff:ff:ff:ff:ff (0 bits) SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf nl80211: Added 802.11b mode based on 802.11g information HT40: control channel: 2 secondary channel: 6 RATE[0] rate=10 flags=0x2 RATE[1] rate=20 flags=0x6 RATE[2] rate=55 flags=0x6 RATE[3] rate=110 flags=0x6 RATE[4] rate=60 flags=0x0 RATE[5] rate=90 flags=0x0 RATE[6] rate=120 flags=0x0 RATE[7] rate=180 flags=0x0 RATE[8] rate=240 flags=0x0 RATE[9] rate=360 flags=0x0 RATE[10] rate=480 flags=0x0 RATE[11] rate=540 flags=0x0 Passive scanning not supported Mode: IEEE 802.11g Channel: 2 Frequency: 2417 MHz Flushing old station entries Deauthenticate all stations Using interface wlan1 with hwaddr 1c:bd:b9:d5:e8:3c and ssid 'erikbandersen.com/freewifi' wlan1: Setup of interface done. MGMT (TX callback) ACK Malformed netlink message: len=436 left=256 plen=420 256 extra bytes in the end of netlink message MGMT (TX callback) ACK mgmt::proberesp cb MGMT (TX callback) ACK mgmt::proberesp cb MGMT (TX callback) ACK mgmt::proberesp cb mgmt::auth authentication: STA=3c:4a:92:0e:41:2f auth_alg=0 auth_transaction=1 status_code=0 wep=0 New STA wlan1: STA 3c:4a:92:0e:41:2f IEEE 802.11: authentication OK (open system) wlan1: STA 3c:4a:92:0e:41:2f MLME: MLME-AUTHENTICATE.indication(3c:4a:92:0e:41:2f, OPEN_SYSTEM) wlan1: STA 3c:4a:92:0e:41:2f MLME: MLME-DELETEKEYS.request(3c:4a:92:0e:41:2f) authentication reply: STA=3c:4a:92:0e:41:2f auth_alg=0 auth_transaction=2 resp=0 (IE len=0) MGMT (TX callback) ACK mgmt::auth cb wlan1: STA 3c:4a:92:0e:41:2f IEEE 802.11: authenticated mgmt::assoc_req association request: STA=3c:4a:92:0e:41:2f capab_info=0x421 listen_interval=10 Validating WMM IE: OUI 00:50:f2 OUI type 2 OUI sub-type 0 version 1 QoS info 0x0 HT: STA 3c:4a:92:0e:41:2f HT Capabilities Info: 0x102c handle_assoc STA 3c:4a:92:0e:41:2f - no greenfield, num of non-gf stations 1 handle_assoc STA 3c:4a:92:0e:41:2f - 20 MHz HT, num of 20MHz HT STAs 1 hostapd_ht_operation_update current operation mode=0x0 hostapd_ht_operation_update new operation mode=0x7 changes=2 new AID 1 wlan1: STA 3c:4a:92:0e:41:2f IEEE 802.11: association OK (aid 1) MGMT (TX callback) ACK mgmt::assoc_resp cb wlan1: STA 3c:4a:92:0e:41:2f IEEE 802.11: associated (aid 1) wlan1: STA 3c:4a:92:0e:41:2f MLME: MLME-ASSOCIATE.indication(3c:4a:92:0e:41:2f) wlan1: STA 3c:4a:92:0e:41:2f MLME: MLME-DELETEKEYS.request(3c:4a:92:0e:41:2f) wlan1: STA 3c:4a:92:0e:41:2f RADIUS: starting accounting session 4DAC8224-00000000 MGMT (TX callback) ACK mgmt::action cb MGMT (TX callback) ACK mgmt::proberesp cb MGMT (TX callback) ACK mgmt::proberesp cb MGMT (TX callback) ACK mgmt::proberesp cb MGMT (TX callback) ACK mgmt::proberesp cb MGMT (TX callback) ACK mgmt::proberesp cb Signal 2 received - terminating wlan1: STA 3c:4a:92:0e:41:2f MLME: MLME-DEAUTHENTICATE.indication(3c:4a:92:0e:41:2f, 1) wlan1: STA 3c:4a:92:0e:41:2f MLME: MLME-DELETEKEYS.request(3c:4a:92:0e:41:2f) Removing station 3c:4a:92:0e:41:2f hostapd_ht_operation_update current operation mode=0x7 hostapd_ht_operation_update new operation mode=0x0 changes=2 Flushing old station entries Deauthenticate all stations . Linux erikbandersen 2.6.35-25-generic #44-Ubuntu SMP Fri Jan 21 17:40:44 UTC 2011 x86_64 GNU/Linux Configuration file: hostapd.conf ctrl_interface_group=0 Opening raw packet socket for ifindex 248 BSS count 1, BSSID mask ff:ff:ff:ff:ff:ff (0 bits) SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf nl80211: Added 802.11b mode based on 802.11g information Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=27 dBm HT40: control channel: 2 secondary channel: 6 RATE[0] rate=10 flags=0x2 RATE[1] rate=20 flags=0x6 RATE[2] rate=55 flags=0x6 RATE[3] rate=110 flags=0x6 RATE[4] rate=60 flags=0x0 RATE[5] rate=90 flags=0x0 RATE[6] rate=120 flags=0x0 RATE[7] rate=180 flags=0x0 RATE[8] rate=240 flags=0x0 RATE[9] rate=360 flags=0x0 RATE[10] rate=480 flags=0x0 RATE[11] rate=540 flags=0x0 Passive scanning not supported Mode: IEEE 802.11g Channel: 2 Frequency: 2417 MHz Could not set channel for kernel driver wlan1: Unable to setup interface. My wireless card is listed as 02:00.0 Network controller: Atheros Communications Inc. AR5008 Wireless Network Adapter (rev 01) by lspci. Am I doing it wrong and there's a new way of doing it? I'm holding off upgrading to Natty because of this. What changed between the versions that would cause this? Should I report it as a bug?

  Read the article

• DVD not detected?

  - by Benjamin

  As i insert a DVD in my drive (on a laptop) using Kubuntu 12.04, the DVD is not detected. The drive takes the DVD, I can hear it munching on it for a while, and then nothing. Even ejecting the DVD becomes a hassle, I need to do that at boot time otherwise the OS won't allow me to eject. Kubuntu 12.04 used to read and mount the same DVDs just fine a week ago. Edit: since I am able to boot from CD, can I safely assume the issue is not a hardware issue? How can I fix this? wodim --devices returns: wodim: Overview of accessible drives (1 found) : ------------------------------------------------------------------------- 0 dev='/dev/sg1' rwrw-- : 'Optiarc' 'DVD+-RW AD-7640A' ------------------------------------------------------------------------- sudo lshw -class disk returns: *-cdrom description: DVD-RAM writer product: DVD+-RW AD-7640A vendor: Optiarc physical id: 0.0.0 bus info: scsi@3:0.0.0 logical name: /dev/cdrom2 logical name: /dev/cdrw2 logical name: /dev/dvd2 logical name: /dev/dvdrw2 logical name: /dev/sr0 version: JD06 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=open lspci returns: 00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 0c) 00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (primary) (rev 0c) 00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (secondary) (rev 0c) 00:1a.0 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 03) 00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 (rev 03) 00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f3) 00:1f.0 ISA bridge: Intel Corporation 82801HM (ICH8M) LPC Interface Controller (rev 03) 00:1f.1 IDE interface: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 03) 06:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) 07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) 08:05.0 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) 08:05.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 02) 08:05.3 Mass storage controller: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) and lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 003: ID 0c45:63e0 Microdia Sonix Integrated Webcam Bus 003 Device 002: ID 0483:2016 SGS Thomson Microelectronics Fingerprint Reader The /etc/modprobe.d/blacklist.conf contains: # This file lists those modules which we don't want to be loaded by # alias expansion, usually so some other driver will be loaded for the # device instead. # evbug is a debug tool that should be loaded explicitly blacklist evbug # these drivers are very simple, the HID drivers are usually preferred blacklist usbmouse blacklist usbkbd # replaced by e100 blacklist eepro100 # replaced by tulip blacklist de4x5 # causes no end of confusion by creating unexpected network interfaces blacklist eth1394 # snd_intel8x0m can interfere with snd_intel8x0, doesn't seem to support much # hardware on its own (Ubuntu bug #2011, #6810) blacklist snd_intel8x0m # Conflicts with dvb driver (which is better for handling this device) blacklist snd_aw2 # causes failure to suspend on HP compaq nc6000 (Ubuntu: #10306) blacklist i2c_i801 # replaced by p54pci blacklist prism54 # replaced by b43 and ssb. blacklist bcm43xx # most apps now use garmin usb driver directly (Ubuntu: #114565) blacklist garmin_gps # replaced by asus-laptop (Ubuntu: #184721) blacklist asus_acpi # low-quality, just noise when being used for sound playback, causes # hangs at desktop session start (Ubuntu: #246969) blacklist snd_pcsp # ugly and loud noise, getting on everyone's nerves; this should be done by a # nice pulseaudio bing (Ubuntu: #77010) blacklist pcspkr # EDAC driver for amd76x clashes with the agp driver preventing the aperture # from being initialised (Ubuntu: #297750). Blacklist so that the driver # continues to build and is installable for the few cases where its # really needed. blacklist amd76x_edac

  Read the article

• I have a problem with a AE1200 Cisco/Linksys Wireless-N USB adapter having stopped working after I ran the update manager in Ubuntu 12.04

  - by user69670

  Here is the problem, I use a Cisco/Linksys AE1200 wireless network adapter to connect my desktop to a public wifi internet connection. I use ndiswrapper to use the windows driver and it had been working fine for me untill I ran the update manager overnight a few days ago. When I woke up it was asking for the normal computer restart to implement the changes but after rebooting the computer, the wireless adapter did not work, the status light on the adapter did not light up even though ubuntu recognizes it is there and according to ndiswrapper the drivers are loaded and the hardware is present. the grep command is being a bitch for some unknown reason today so this will be long sorry Output from "lspci": 00:00.0 Host bridge: Advanced Micro Devices [AMD] nee ATI Radeon Xpress 200 Host Bridge (rev 01) 00:01.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RS480 PCI Bridge 00:12.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB600 Non-Raid-5 SATA 00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI0) 00:13.1 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI1) 00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI2) 00:13.3 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI3) 00:13.4 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI4) 00:13.5 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB Controller (EHCI) 00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 13) 00:14.1 IDE interface: Advanced Micro Devices [AMD] nee ATI SB600 IDE 00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB600 PCI to LPC Bridge 00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge 01:05.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RC410 [Radeon Xpress 200] 02:02.0 Communication controller: Conexant Systems, Inc. HSF 56k Data/Fax Modem 02:03.0 Multimedia audio controller: Creative Labs CA0106 Soundblaster 02:05.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Output from "lsusb": Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 009: ID 13b1:0039 Linksys AE1200 802.11bgn Wireless Adapter [Broadcom BCM43235] Bus 003 Device 002: ID 045e:0053 Microsoft Corp. Optical Mouse Bus 004 Device 002: ID 1043:8006 iCreate Technologies Corp. Flash Disk 32-256 MB Output from "ifconfig": eth0 Link encap:Ethernet HWaddr 00:19:21:b6:af:7c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:20 Base address:0xb400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:13232 errors:0 dropped:0 overruns:0 frame:0 TX packets:13232 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1084624 (1.0 MB) TX bytes:1084624 (1.0 MB) Output from "iwconfig": lo no wireless extensions. eth0 no wireless extensions. Output from "lsmod": Module Size Used by nls_iso8859_1 12617 1 nls_cp437 12751 1 vfat 17308 1 fat 55605 1 vfat uas 17828 0 usb_storage 39646 1 nls_utf8 12493 1 udf 84366 1 crc_itu_t 12627 1 udf snd_ca0106 39279 2 snd_ac97_codec 106082 1 snd_ca0106 ac97_bus 12642 1 snd_ac97_codec snd_pcm 80845 2 snd_ca0106,snd_ac97_codec rfcomm 38139 0 snd_seq_midi 13132 0 snd_rawmidi 25424 2 snd_ca0106,snd_seq_midi bnep 17830 2 parport_pc 32114 0 bluetooth 158438 10 rfcomm,bnep ppdev 12849 0 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq snd 62064 11 snd_ca0106, snd_ac97_codec,snd_pcm,snd_rawj9fe snd_ca0106,snd_ac97_codec,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 14635 1 snd snd_page_alloc 14108 2 snd_ca0106,snd_pcm sp5100_tco 13495 0 i2c_piix4 13093 0 radeon 733693 3 ttm 65344 1 radeon drm_kms_helper 45466 1 radeon drm 197692 5 radeon,ttm,drm_kms_helper i2c_algo_bit 13199 1 radeon mac_hid 13077 0 shpchp 32325 0 ati_agp 13242 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp usbhid 41906 0 hid 77367 1 usbhid 8139too 23283 0 8139cp 26759 0 pata_atiixp 12999 1 Output from "sudo lshw -C network": *-network description: Ethernet interface product: RTL-8139/8139C/8139C+ vendor: Realtek Semiconductor Co., Ltd. physical id: 5 bus info: pci@0000:02:05.0 logical name: eth0 version: 10 serial: 00:19:21:b6:af:7c size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 10 0bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=half latency=64 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s resources: irq:20 ioport:b400(size=256) memory:ff5fdc00-ff5fdcff Output from "iwlist scan": lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. Output from "lsb_release -d": Ubuntu 12.04 LTS Output from "uname -mr": 3.2.0-24-generic-pae i686 Output from "sudo /etc/init.d/networking restart": * Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces * Reconfiguring network interfaces... [ OK ]

  Read the article

• Wireless Problem on Acer Aspire 5610z

  - by Ugur Can Yalaki

  I installed ubuntu 12.04 on my machine, but I can't get wireless connection to work. My computer is Acer Aspire 5610z. I found that some other people that have same computer, face the same problem. Here is some information about it: ****** info trace ****** * uname -a * Linux ucy-Aspire-5610Z 3.8.0-32-generic #47~precise1-Ubuntu SMP Wed Oct 2 16:22:28 UTC 2013 i686 i686 i386 GNU/Linux * lsb_release * Distributor ID: Ubuntu Description: Ubuntu 12.04.3 LTS Release: 12.04 Codename: precise * lspci * 05:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN [14e4:4311] (rev 01) Subsystem: AMBIT Microsystem Corp. Device [1468:0422] Kernel driver in use: b43-pci-bridge 06:01.0 Ethernet controller [0200]: Broadcom Corporation BCM4401-B0 100Base-TX [14e4:170c] (rev 02) Subsystem: Acer Incorporated [ALI] Device [1025:0090] Kernel driver in use: b44 * lsusb * Bus 001 Device 004: ID 04e8:6863 Samsung Electronics Co., Ltd Bus 001 Device 002: ID 5986:0100 Acer, Inc Orbicam Bus 002 Device 002: ID 046d:c52f Logitech, Inc. Wireless Mouse M305 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub * PCMCIA Card Info * PRODID_1="" PRODID_2="" PRODID_3="" PRODID_4="" MANFID=0000,0000 FUNCID=255 * iwconfig * * rfkill * 0: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no * lsmod * ssb_hcd 12781 0 ssb 51554 2 ssb_hcd,b44 * nm-tool * NetworkManager Tool State: connected (global) Device: usb0 [Wired connection 2] ------------------------------------------- Type: Wired Driver: rndis_host State: connected Default: yes HW Address: Capabilities: Carrier Detect: yes Wired Properties Carrier: on IPv4 Settings: Address: 192.168.42.7 Prefix: 24 (255.255.255.0) Gateway: 192.168.42.129 DNS: 192.168.42.129 IPv6 Settings: Address: ::a05d:a1ff:fea4:1738 Prefix: 64 Gateway: fe80::504d:76ff:fe86:db04 Address: fe80::a05d:a1ff:fea4:1738 Prefix: 64 Gateway: fe80::504d:76ff:fe86:db04 DNS: fe80::504d:76ff:fe86:db04 Device: eth2 ----------------------------------------------------------------- Type: Wired Driver: b44 State: unavailable Default: no HW Address: Capabilities: Carrier Detect: yes Wired Properties Carrier: off * NetworkManager.state * [main] NetworkingEnabled=true WirelessEnabled=true WWANEnabled=true WimaxEnabled=true * NetworkManager.conf * [main] plugins=ifupdown,keyfile dns=dnsmasq [ifupdown] managed=false * interfaces * auto lo iface lo inet loopback * iwlist * * resolv.conf * nameserver 127.0.0.1 * blacklist * [/etc/modprobe.d/blacklist-ath_pci.conf] blacklist ath_pci [/etc/modprobe.d/blacklist-bcm43.conf] blacklist b43 blacklist b43legacy blacklist ssb blacklist bcm43xx blacklist brcm80211 blacklist brcmfmac blacklist brcmsmac blacklist bcma [/etc/modprobe.d/blacklist.conf] blacklist evbug blacklist usbmouse blacklist usbkbd blacklist eepro100 blacklist de4x5 blacklist eth1394 blacklist snd_intel8x0m blacklist snd_aw2 blacklist i2c_i801 blacklist prism54 blacklist bcm43xx blacklist garmin_gps blacklist asus_acpi blacklist snd_pcsp blacklist pcspkr blacklist amd76x_edac * modinfo * filename: /lib/modules/3.8.0-32-generic/kernel/drivers/usb/host/ssb-hcd.ko license: GPL description: Common USB driver for SSB Bus author: Hauke Mehrtens srcversion: E127A51EDC8F44D2C2A8F15 alias: ssb:v4243id0819rev* alias: ssb:v4243id0817rev* alias: ssb:v4243id0808rev* depends: ssb intree: Y vermagic: 3.8.0-32-generic SMP mod_unload modversions 686 filename: /lib/modules/3.8.0-32-generic/kernel/drivers/ssb/ssb.ko license: GPL description: Sonics Silicon Backplane driver srcversion: 14621F6EC014F731244437C alias: pci:v000014E4d00004350sv*sd*bc*sc*i* alias: pci:v000014E4d0000432Csv*sd*bc*sc*i* alias: pci:v000014E4d0000432Bsv*sd*bc*sc*i* alias: pci:v000014E4d00004329sv*sd*bc*sc*i* alias: pci:v000014E4d00004328sv*sd*bc*sc*i* alias: pci:v000014E4d00004325sv*sd*bc*sc*i* alias: pci:v000014E4d00004324sv*sd*bc*sc*i* alias: pci:v000014E4d0000A8D6sv*sd*bc*sc*i* alias: pci:v000014E4d00004322sv*sd*bc*sc*i* alias: pci:v000014E4d00004321sv*sd*bc*sc*i* alias: pci:v000014E4d00004320sv*sd*bc*sc*i* alias: pci:v000014E4d00004319sv*sd*bc*sc*i* alias: pci:v000014A4d00004318sv*sd*bc*sc*i* alias: pci:v000014E4d00004318sv*sd*bc*sc*i* alias: pci:v000014E4d00004315sv*sd*bc*sc*i* alias: pci:v000014E4d00004312sv*sd*bc*sc*i* alias: pci:v000014E4d00004311sv*sd*bc*sc*i* alias: pci:v000014E4d00004307sv*sd*bc*sc*i* alias: pci:v000014E4d00004306sv*sd*bc*sc*i* alias: pci:v000014E4d00004301sv*sd*bc*sc*i* depends: intree: Y vermagic: 3.8.0-32-generic SMP mod_unload modversions 686 * udev rules * PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1e.0/0000:06:01.0/ssb1:0 (b44) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0" PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1e.0/0000:06:01.0/ssb2:0 (b44) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth1" PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1e.0/0000:06:01.0/ssb3:0 (b44) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth2" * dmesg * [ 2.385241] ssb: Found chip with id 0x4311, rev 0x01 and package 0x00 [ 2.385256] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x11, vendor 0x4243) [ 2.385266] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x0A, vendor 0x4243) [ 2.385276] ssb: Core 2 found: USB 1.1 Host (cc 0x817, rev 0x03, vendor 0x4243) [ 2.385286] ssb: Core 3 found: PCI-E (cc 0x820, rev 0x01, vendor 0x4243) [ 2.448147] ssb: Sonics Silicon Backplane found on PCI device 0000:05:00.0 [ 2.468112] ssb: Found chip with id 0x4401, rev 0x02 and package 0x00 [ 2.468124] ssb: Core 0 found: Fast Ethernet (cc 0x806, rev 0x07, vendor 0x4243) [ 2.468132] ssb: Core 1 found: V90 (cc 0x807, rev 0x03, vendor 0x4243) [ 2.468140] ssb: Core 2 found: PCI (cc 0x804, rev 0x0A, vendor 0x4243) [ 2.508230] ssb: Sonics Silicon Backplane found on PCI device 0000:06:01.0 [ 2.528620] b44 ssb1:0 eth0: Broadcom 44xx/47xx 10/100 PCI ethernet driver ******** done ******** Thank you already for your help.

  Read the article

< Previous Page | 18 19 20 21 22 23 24  | Next Page >