Search Results

Search found 594 results on 24 pages for 'ppa'.

Page 22/24 | < Previous Page | 18 19 20 21 22 23 24  | Next Page >

  • Ubuntu 12.04.1 LTS and Nvidia dirver (304.51) 64bit: problem 640x480

    - by nibianaswen
    I have a problem with this configuration: Asus K55V, Ubuntu 12.04 LTS and Nvidia driver 304.51. I have remove the nouveau driver with: apt-get --purge remove xserver-xorg-video-nouveau I installed the official nvidia driver (from www.nvidia.com) but when I reboot the PC the resolution of screen is only 640x480 and the monitor is resized. Mo solution at this problem if i change the xorg.conf. Now i have uninstall the nvidia driver and reinstall with sudo apt-get purge nvidia-current sudo apt-add-repository ppa:ubuntu-x-swat/x-updates sudo apt-get update sudo apt-get install nvidia-current When I reboot the screen resolution and size is OK, but if I start nvidia-setting I received the message: You do not appear to be using the NVIDIA X driver. and with command: sudo lshw -c display | grep driver I received configuration: driver=i915 latency=0 This sound like the system is using the Intel card. When I launch command lspci | grep VGA the output is: 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 01:00.0 VGA compatible controller: NVIDIA Corporation Device 1058 (rev ff) And there is no /etc/X11/xorg.conf. I have read a lot of guides on internet but without success.. How i can use nvidia card with the driver that i have installed?

    Read the article

  • Pandaboard crash on startup or freeze after minutes

    - by Meach
    I just received my Pandaboard ES (rev B) and I am having trouble after installing ubuntu-omap4-addons. Once I copied the image ubuntu-12.04-preinstalled-desktop-armhf+omap4.img on my sd card and boot the pandaboard with it, I run the following commands: sudo add-apt-repository ppa:tiomap-dev/release sudo apt-get update sudo apt-get dist-upgrade sudo apt-get install ubuntu-omap4-extras At the end of the installation of ubuntu-omap4-extras, Ubuntu tells me that a problem occurs when the console displays: ldconfig deferred processing now taking place Clicking on "report the problem" tell me that the problem concerns pvr-omap4-dkms. I read somewhere that this can happen and it is better to reinstall pvr-omap4-dkms. Which I am doing by running: sudo apt-get install --reinstall pvr-omap4-dkms I reboot. Then the board has sometimes difficulties to start Ubuntu: it freezes during the loading page, only action I can do is unplugging the board to start it again. Some other times, Ubuntu load successfully but then freeze at another random time, in the range 20 - 40 minutes. I searched on internet for similar bug and found this: https://bugs.launchpad.net/ubuntu/+source/linux-ti-omap4/+bug/971091 So I typed this in: update-rc.d ondemand disable apt-get -y install cpufrequtils echo 'ENABLE="true" GOVERNOR="performance" MAX_SPEED="0" MIN_SPEED="0"' > /etc/default/cpufrequtils cpufreq-set -r -g performance reboot But it doesn't seems to fix the bug. Another detail: on startup, before the loading screen of Ubuntu (when there is the two penguins displayed :)), it shows this: [0.297271] CPU1: Unknown IPI message 0x1 [0.308990] omap_hwmod: mcpdm: _wait_target_ready error: -16 [0.354705] omap_mux_get_by_name: Could not find signal uart1_cts.uart1_cts [0.354766] omap_hwmod_mux_init: Could not allocate device mux entry [2.107086] thermal_get_slope:Getting slope is not supported for domain gpu [2.107116] thermal_get_offset:Getting offset is not supported for domain gpu [2.107299] stm_fw: vendor driver stm_ti1.0 registered [8.725555] OMAPRPC: Registration of OMAPRPC rpmsg service returned 0! debug=0 Any idea what can be wrong? I am not that good with Ubuntu so any help will be appreciated. Cheers! Meach

    Read the article

  • How to install Tor (Web Browser) in Ubuntu 12.10?

    - by Zignd
    I would like to install the Tor, but I'm having some problems. I know that someone will say "This question is a exactly duplication of How to install tor?", but it's not, because the another question can not be applied to Ubuntu 12.10 as the deb command is not available anymore. I did a research and even at the Tor's Official Website the available resource can not be applied to Ubuntu 12.10. I tried to use the deb command (as the above question says: deb http://deb.torproject.org/torproject.org <DISTRIBUTION> main) and the Terminal says deb: command not found and when I try to install it says E: Unable to locate package deb. I've also tried to use the ppa: ubun-tor, but it's not compatible with Quantal Quetzal, because it's too old. I've also tried to use sudo apt-get install tor, but browser icon don't shows up after installation and if you try to use the command tor in the Terminal I get the following error message: Nov 26 10:59:25.731 [notice] Tor v0.2.3.22-rc (git-4a0c70a817797420) running on Linux. Nov 26 10:59:25.731 [notice] Tor can't help you if you use it wrong! Learn how to be safe at https://www.torproject.org/download/download#warning Nov 26 10:59:25.731 [notice] Read configuration file "/etc/tor/torrc". Nov 26 10:59:25.737 [notice] Initialized libevent version 2.0.19-stable using method epoll (with changelist). Good. Nov 26 10:59:25.737 [notice] Opening Socks listener on 127.0.0.1:9050 Nov 26 10:59:25.737 [warn] Could not bind to 127.0.0.1:9050: Address already in use. Is Tor already running? Nov 26 10:59:25.737 [warn] Failed to parse/validate config: Failed to bind one of the listener ports. Nov 26 10:59:25.737 [err] Reading config failed--see warnings above. Thanks in advance.

    Read the article

  • How can I stop Chromium from putting focus in the address bar when using the up arrow key to scroll

    - by codeLes
    This is bugging me. I'm at a web page, any web page, and I am scrolling back to the top of the page with the up arrow key as I tend to do when browsing a page and once I get to the top of the page if I don't pay attention and hit the key one more times than is needed Chromium in all it's wisdom decides I must want to do something with the address so it places the focus in the address bar. ARGH! Any way to stop this? I'm running Ubuntu 9.04 Jaunty and have installed the nightly build version of Chromium PPA.

    Read the article

  • How do I finish installing Sun JDK after cancelling out of the legal term screen?

    - by Ravi
    I am a newcomer to linux and have had lots of problems in installing java on my newly installed Ubuntu 11.10. I use a statistical programming environment called R and many of the packages there require java (the sun variety, I am told). I tried the following : sudo add-apt-repository ppa:ferramroberto/java sudo apt-get update sudo apt-get install sun-java6-jre sun-java6-plugin sun-java6-fonts (after this, I wanted to continue with (but never got that far) : sudo apt-get install sun-java6-jdk After this, a window appeared with the heading, "Configuring jre", or something like that. Below was a long list of legal text about accepting Sun's terms. I did not know how to close this window (no obvious option like pressing return worked). After a long time, when nothing seemed to happen, I finally closed the window. After that, I could not open synaptic. I got the error message : dpkg was interrupted. You must manually run 'sudo dpkg --configure -a' I did this. But it does not help. I have java as a "broken" program. When I try to remove the program from synaptic, I get a message that I must reinstall it again.I do not know what I should do. I want to install jdk6. And also remove the open jdk which is still persistently present in my system. I tried the clean and purge command shown below. Next, I tried to remove the sun-java6-jre from synaptic. I get the following message :E: sun-java6-jre: Package is in a very bad inconsistent state - you should reinstall it before attempting a removal. When I tried to follow the procedure suggested in the related question (from the link suggested below), I get the following message on trying to install again :Could not mark all packages for installation or upgrade.The following packages have unresolvable dependancies. Make sure that all required repositories are added and enabled in the preferences. sun-java6-bin : Depends: sun-java6-jre but it is not going to be installed

    Read the article

  • How to help FGLRX detect a device

    - by user113416
    I have HD 4850 card, Ubuntu 12.10 and installed legacy drivers using makson96 ppa. The issue is, that FGLRX can not detect my device and loads vesa bios. I had the same problem on ubuntu 11.10, 12.04 versions. I want to manually help fglrx find a matching device to load as it shoudld do. It is interesting, why does fglrx search for a device in a PCI:0@1:0:1 Bus? in xorg.cof different bus is indicated: Section "Device" Identifier "aticonfig-Device[0]-0" Driver "fglrx" BusID "PCI:1:0:0" EndSection fglrxinfo display: :0.0 screen: 0 OpenGL vendor string: Advanced Micro Devices, Inc. OpenGL renderer string: ATI Radeon HD 4800 Series OpenGL version string: 3.3.11653 Compatibility Profile Context Here is a part of my xorg log: [ 3.846] (II) VESA: driver for VESA chipsets: vesa [ 3.846] (II) FBDEV: driver for framebuffer: fbdev [ 3.846] (++) using VT number 7 [ 3.846] (WW) Falling back to old probe method for fglrx [ 3.883] (II) Loading PCS database from /etc/ati/amdpcsdb [ 3.883] (--) Assigning device section with no busID to primary device [ 3.883] (--) Chipset Supported AMD Graphics Processor (0x9442) found [ 3.884] (WW) fglrx: No matching Device section for instance (BusID PCI:0@1:0:1) found [ 3.884] (II) AMD Video driver is running on a device belonging to a group targeted for this release [ 3.884] (II) AMD Video driver is signed [ 3.884] (II) fglrx(0): pEnt->device->identifier=0xb7791d8f [ 3.884] (WW) Falling back to old probe method for vesa [ 3.884] (WW) Falling back to old probe method for fbdev Thanks in advance.

    Read the article

  • install filezilla error, Depends: libatk1.0-0 (>= 1.29.3) but 1.28.0-0ubuntu1 is to be installed

    - by solomongaby
    I am trying to install filezilla from this repo: https://launchpad.net/~yofel/+archive/ppa and after sudo apt-get update i tried to install it but i get the error: Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: filezilla: Depends: libatk1.0-0 (>= 1.29.3) but 1.28.0-0ubuntu1 is to be installed Do you have any ideea what is happening ?

    Read the article

  • how to properly Install chromium from zip and make it the default browser

    - by ClarifyLinux
    Since the Chromium PPA is no longer maintained, for those of us preferring to use chromium over chrome, we have two options: Build and Install from Source Download either 'beta' or daily builds (in a zip file) Unfortunately for me, option 1 is overly complicated. I know how to compile most any other applications in Ubuntu but I've never been able to get chromium to build correctly. I am currently using option 2. In Chromium I have the Chromium Updater installed (http://goo.gl/ffAMy). This gives me quick access to the most recent 64bit versions. Once downloaded, I install to /home/myuser/opt/chrome-linux. From this directory I can run the chrome binary. It works perfectly except for the fact that I cannot get it to act as my default browser. I've tried, as root, installing the binary in /opt/chrome-linux/ with a symbolic link to the 'chrome' binary in /usr/bin. Unfortunately, this doesn't work as a non root user. So my question is - How do I properly install a downloaded chromium zip build so tht it's listed as an option for the default browser?

    Read the article

  • How can I enable readline for PHP 5.4 on Ubuntu 11.10?

    - by dotweb
    I installed PHP 5.4 on my Ubuntu 11.10 PC like this: $ sudo add-apt-repository ppa:ondrej/php5 $ sudo apt-get update $ sudo apt-get install php5 It's working fine but I don't have the readline function anymore that I need for my PHP CLI scripts. libreadline-dev is installed and readline was working perfectly in 5.3. I also tried to compile 5.4 with readline: $ wget http://de2.php.net/get/php-5.4.0.tar.gz/from/de.php.net/mirror $ tar xzvf mirror $ cd php-5.4.0/ $ ./configure --with-readline $ make test But the last command echoed this error after compiling for some minutes: FAILED TEST SUMMARY Test 7: DTD tests [ext/dom/tests/dom007.phpt] You may have found a problem in PHP. I appreciate any help on how to get readline working!

    Read the article

  • Why doesn't unity show icons or panel after installing numix theme?

    - by Sid
    I'm a beginner to Ubuntu/Linux and I have a problem: Unity is not loading! When I choose Unity in the log-in screen, I get notifications and I can see the mouse, but that's it. I have Ubuntu 14.04 installed, along with Bumblebee/Primus. I had no issues whatsoever, until I decided to try the numix-theme and the numix icon pack. I added the PPA and installed it, but when I logged off and logged back on, nothing showed up. I panicked, and in tty1, I purged numix-* but that did not solve the issue. To get by day-to-day use, I installed gnome-flashback, and among those environments, only the metacity one works. (The compiz one does not.) I've tried installing the unity-tweak-tool to reset unit, installing dconf and doing: dconf reset -f /org/compiz/ but that didn't work either. One site even told me to delete /org/compiz/, but that did not resolve the issue. When I checked ccsm, the Unity plugin had a check to it. I also tried with Unity doesn't load, no Launcher, no Dash appears, but it gets stuck on "loading icons". Any help will be awesome!

    Read the article

  • Banshee doesn't like opening websites

    - by Allan
    I have come across two bugs (which will be added to launchpad if it's not resolved here) When I open any of the websites in Banshee Amazon or Miro Guide as soon as the site is finished loading it crashes Banshee. If I play any video local or remote it will show 1 frame maybe 0.5 sec of video then I get a black screen and audio continues in the backgound. Specs & Details I have a Fujitsu Amilo 1718 laptop with 2 gig of ram (original 1 gig) graphics is provided by ATI Radeon Xpress 200M (don't laugh it works with compiz....just) I have a link to the output of banshee --debug Here Don't have time to read? Here are the Highlights [2 Warn 11:52:34.814] Caught an exception - System.ArgumentNullException: Argument cannot be null. then abit later Debug info from gdb: Could not attach to process. If your uid matches the uid of the target process, check the setting of /proc/sys/kernel/yama/ptrace_scope, or try again as the root user. For more details, see /etc/sysctl.d/10-ptrace.conf ptrace: Operation not permitted. ================================================================= Got a SIGSEGV while executing native code. This usually indicates a fatal error in the mono runtime or one of the native libraries used by your application. ================================================================= Aborted Not music to my ears as you can expect. The version I am using is 1.9.4 from the daily ppa but these bugs happen in any version of banshee from 1.8.1 and up. So if any one has come across a fix for this problem please share!! additional info Both VLC and Miro work on my system so there isn't a system wide problem with video and I haven't mentioned mono so no trolling it will get voted down.

    Read the article

  • Ubuntu 12.04 - default Radeon driver does not work at all

    - by mumble
    I've recently upgraded to 12.04 LTS and I have an ATI Radeon HD5670. I've heard that the open source 'Radeon' driver is used by default. However, it wasn't showing anything for me. What I did was I added the 'nomodeset' option to boot up and install fglrx. But it didn't work well for me as it introduced a lot of problems (freezes/glitches). So I removed/purged fglrx and am planning to use the open source drivers instead. So my question is this: Why is my default Radeon driver not working? Is anyone having a similar issue? I've also tried using the ubuntu-x-swat driver by running the ff commands: sudo add-apt-repository ppa:ubuntu-x-swat/x-updates sudo apt-get update But the result was the same as the Radeon driver. Nothing shows up on system boot. Any ideas? Thanks in advance! Update Running lspci -nn | grep VGA gives me the following: 02:00.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI Redwood [Radeon HD 5670] [1002:68d8]

    Read the article

  • My computer will not reboot after fresh install of ubuntu 12.04LTS

    - by user170715
    I bought a new computer yesterday and it came with Windows 8. When installing Ubuntu, i choose the erase and install option thinking that Ubuntu would install easily like it did for my old laptop... After a successful install and following the instructions telling me to reboot to finish installation and remove installation media. It worked and my computer booted fine, however once I began installing updates via update manager and activating additional driver {ATI/AMD proprietary FGLRX graphics driver (post-release updates)} out of the following: Experimental AMD binary Xorg driver and kernel module ATI/AMD proprietary FGLRX graphics driver (*experimental*beta) ATI/AMD proprietary FGLRX graphics driver (post-release updates) Then reboot to finish making changes I reboot and get an error (Reboot and select proper boot device) At this point I was stuck, so I eventually reinstalled ubuntu and repeated the exacted same steps until right before i rebooted to finish making changes. However this time i used this Boot Repair tool sudo add-apt-repository ppa:yannubuntu/boot-repair sudo apt-get update sudo apt-get install -y boot-repair boot-repair After running the program i get a "boot successfully repaired" message. Then I try to reboot again and get the GNU Grub screen where it says would you like to boot: normal recovery memorytest Once it begins loading, you see the code moving across the screen then it pauses when it gets to and doesnt do anything. If someone could tell me how to fix this or get Windows 8 back soon, I'd appreciate it because like i said i just bought it yesterday and now i cant even use it.

    Read the article

  • Error when installing ubuntu-zfs

    - by ubiquibacon
    I'm switching from FreeNAS to Ubuntu 12.04 LTS. After a vanilla install of Ubuntu has been completed I run the following commands in the order shown to install ZFS: apt-get install python-software-properties add-apt-repository ppa:zfs-native/stable apt-get -y -q update && apt-get -y -q upgrade apt-get install ubuntu-zfs When the last command is run ZFS is installed and seems to be working correctly... mostly (more on that later). However, when the last command is run I get this error (full log here): configure: error: *** Please make sure the kmod spl devel <kernel> package for your *** distribution is installed then try again. If that fails you *** can specify the location of the spl objects with the *** '--with-spl-obj=PATH' option. What is this error and how do I fix it? Now I said mostly earlier because my pool's don't auto mount when the server restarts the way they should. All my reading (mostly from this page) indicates that mountall should just take care of the mounting. I have followed the instructions on that page and I cannot get mountall to work correctly. My pools will only auto mount on restart if I edit /etc/fstab or change the ZFS_MOUNT and ZFS_UNMOUNT options in /etc/default/zfs.

    Read the article

  • install filezilla error, Depends: libatk1.0-0 (>= 1.29.3) but 1.28.0-0ubuntu1 is to be installed

    - by solomongaby
    Hello, I am trying to install filezilla from this repo: https://launchpad.net/~yofel/+archive/ppa and after sudo apt-get update i tried to install it but i get the error: Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: filezilla: Depends: libatk1.0-0 (>= 1.29.3) but 1.28.0-0ubuntu1 is to be installed Do you have any ideea what is happening ?

    Read the article

  • Mplayer not working after update

    - by R. Morgenstern
    After an update with update-manager in Unbuntu 12.04, Mplayer is not working anymore. It needs ffmpeg, but it can't be installed due to unmet dependencies. I added a ppa for fmpeg, but did not solve the problem. see output: Python (v2.7) requires to install .... GStreamer ffmpeg video plugin. Codecs to play mpeg, divx, mpeg4, ac3, wmv and asf files. Using Install, I get an error messages that it can't be installed due to unmet dependencies. see list below. How can I fix this problem? Thanks in advance for guidance. Renate The following packages have unmet dependencies: gstreamer0.10-ffmpeg: Depends: libavcodec-extra-53 (>= 4:0.7.3-1) but 4:0.8.3ubuntu0.12.04.1 is to be installed Depends: libavformat-extra-53 (>= 4:0.7.3-1) but 4:0.8.3ubuntu0.12.04.1 is to be installed Depends: libavutil-extra-51 (>= 4:0.7.3-1) but 6:0.10.4.0ubuntu0jon2.2 is to be installed Depends: libc6 (>= 2.7) but 2.15-0ubuntu10 is to be installed Depends: libglib2.0-0 (>= 2.31.2) but 2.32.3-0ubuntu1 is to be installed Depends: libgstreamer-plugins-base0.10-0 (>= 0.10.31) but 0.10.36-1 is to be installed Depends: libgstreamer0.10-0 (>= 0.10.31) but 0.10.36-1ubuntu1 is to be installed Depends: liborc-0.4-0 (>= 1:0.4.16) but 1:0.4.16-1ubuntu2 is to be installed Depends: libpostproc-extra-52 (>= 4:0.7.3-1) but 4:0.8.3ubuntu0.12.04.1 is to be installed Depends: libswscale-extra-2 (>= 4:0.7.3-1) but 4:0.8.3ubuntu0.12.04.1 is to be installed

    Read the article

  • DEBIAN repository signing: a step-by-step guide.

    - by jldupont
    I've got many DEBIAN repository for my projects (e.g. EPAPI, erlang-dbus etc.). It seems that now Synaptic wants those to be signed for the packages to appear by default. For the DEBIAN kung-fu masters out there, please provide me with a step-by-step guide to achieving this, please. I've googled a lot but I am still a bit confused on the subject. update: I use a Launchpad PPA now... saves me from all this trouble.

    Read the article

  • Error while installing an application

    - by Bong.Da.City
    So i have installed synaptic package manager.. via it, i have checked once libopencv-highgui-dev and applied complete removal.. after that i installed it... now everytime i try to install an application e.g Format Junkie sudo add-apt-repository ppa:format-junkie-team/release && sudo apt-get update && sudo apt-get install formatjunkie in the command install format junkie it gives me that error everytime: sudo apt-get install formatjunkie Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: libopencv-features2d-dev : Depends: libopencv-highgui-dev (= 2.3.1-11ubuntu2) but it is not going to be installed E: Error, pkgProblemResolver::Resolve generated breaks, this may be caused by held packages. What should i do? And 2nd what did i did wrong so it won't happen another time? output of lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.10 Release: 12.10 Codename: quantal

    Read the article

  • Ubuntu 14.04 stalling. Problem with LightDM. Plymouth (and logging out) switches over to a black screen w/ white cursor

    - by Kage
    if its a duplicate, sorry. Couldn't find anything that fits my issue, much less that was on 14.04. I changed a few things recently. Switched to the Numix theme (from PPA), installed lm-sensors and psensor (ran all the I/O probes), Ubuntu Tweak, Pinta, and well, Team Fortress 2 on Steam. :P The system will get to the Plymouth 'ubuntu' screen, load load, all dots filled, switches over to LightDM, but wait! No LightDM. :I Just a blank screen with that white cursor. Can't switch out to tty1-6 - not sure if the Ctrl-Alt-F1 is disabled in 14.04 or if its literally just locked down. If I change any files, I have access to the filesystem from my Windows 8 partition. That's it. :/ I'm pretty familiar with Linux, especially Ubuntu, but I think I'm still at the point I know just enough to break things and not always how to fix 'em. Any help would be greatly appreciated. Thanks! UPDATE I was just able to get into my desktop briefly. I booted Ubuntu. When the black screen froze, I hit Ctrl-Alt-Del. When it started switching off, I hit Ctrl-Alt-Backspace. It rebooted. I plugged the second monitor in I had been using before the issue ever came about. Plymouth displayed on both. LightDM came up, displayed on both (it used to show only the ubuntu logo on the unfocused monitor though). I logged in just fine. Even ran some pending software updates. I logged out of the desktop though, and LightDM refused to show again. xP

    Read the article

  • alsa - sound issues on ubuntu 12.04

    - by tam_ubuuser
    i am having an sony E series laptop.i have an HDMI port .at this stage ,i have tested my sound card , which provides audio out on my laptop i.e i could hear songs .my laptop has two sound cards amd 5450 and an intel-hda(alsamixer shows that as s/pdif) . i decided to connect HDMI output to my new HD-TV.but, i could get only visuals on my TV,NO AUDIO OUTPUT ( HDMI cable works fine with win 7).my laptop has two sound cards.but i couldn't switch output to other card.( i don't know ,how to do that) i decided to update alsa. complied the following code in terminal. sudo apt-add-repository ppa:ubuntu-audio-dev/alsa-daily sudo apt-get update sudo apt-get install alsa-hda-dkms then,strangely no login sound, and no audio output on my laptop at all .then, started complied code from step1 sound troubleshooting procedure from offical ubuntu site.then, my speaker icon taskbar disappeared .obivously $aplay -l ,provided output as no soundcards detected . so , i implemented step 4 from that guide, it provides a output of all hardware devices in my laptop. *-multimedia UNCLAIMED description: Audio device product: Cedar HDMI Audio [Radeon HD 5400/6300 Series] vendor: Hynix Semiconductor (Hyundai Electronics) physical id: 0.1 bus info: pci@0000:01:00.1 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi bus_master cap_list configuration: latency=0 resources: memory:f0040000-f0043fff *-multimedia UNCLAIMED description: Audio device product: 5 Series/3400 Series Chipset High Definition Audio vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 05 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f5e00000-f5e03fff that command displayed output name of the two cards . but , still i have no positive output on $aplay -l. so therfore, i think alsa couldn't detect my sound cards . is there solution to this problem? it could be better,if alsa would channel output from multiple sound cards ? how should install and configure alsa such that detects HDMI cable as soon i connect to my HD tv? is it possible to alsa and pluseaudio 2.0 to co-exist, if so how?

    Read the article

  • Can't login to Unity 3d after enabling Xinerama for a short moment

    - by Amir Adar
    Today I connected a second monitor to my computer. I set it up using nVidia's control panel, and all was working quite well, so I figured it won't be a problem to try Xinerama, just to see the difference between that and twinview. After enabling Xinerama and restarting the X session, I saw that I was logged into a Unity 2d session. I thought it was a problem with Xinerama, so I switched back to twinview, but it still logged me into Unity 2d. I tried disconnecting the second monitor, no luck: still Unity 2d. I tried changing GPU drivers and installing drivers from a separate ppa, and still I was logged into Unity 2d. Up until this point, I didn't have any problem logging into Unity 3d. It only happened after I tried using Xinerama. I should note that I was doing all this while updates were going on in the background, so it could be something related to that, though I can't imagine what (I tried booting with another kernel, but no luck). So what exactly happened? Did changing the mode to Xinerama triggered some other changes that I'm not aware of? Did these updates cause a certain malfunction in the driver? Is it something else?

    Read the article

  • Is there a way how to customize my keyboard layout in Xubuntu in a graphical way (by clicking)?

    - by Honza Javorek
    Possible duplicate, but I really couldn't find a solution. I would like to adjust my US keyboard layout, e.g. to add possibility to type some special characters on combination of right Alt + another character, etc. Moreover, my arrow up is dead, so until I buy another keyboard, I'd like to use my right shift as my arrow up, ASAP. However, there seems to be no way how to edit my keyboard layout easily in Xubuntu :( I found no editor and I really don't want to spend years in some configuration files and terminal (not that I can't, but I really really don't want). KLE - the only editor I could find, but no installation guide, no package, no PPA, no idea how to make it working (and uninstallable if not needed one day) Editor in Ubuntu - apparently not present in Xubuntu I found several tutorials how to change the layout, but they all seems to be complicated and not easy to follow. I don't want to spend a weekend in terminal or so, I am looking for an app to launch, make some clicking, finish my work by hitting Save button and - done! Please, is there such solution? For humans?

    Read the article

  • Uninstall ax88179 package

    - by jackbenny
    I've installed the ax88179 package from the PPA (since the ax88179 driver isn't in the 3.8 kernel). But now I'd like to install kernel 3.11.6 and this module is already included here. So I'd like to uninstall the the module from the package but this fails with the following error message The following packages will be REMOVED: ax88179* 0 upgraded, 0 newly installed, 1 to remove and 0 not upgraded. After this operation, 313 kB disk space will be freed. Do you want to continue [Y/n]? (Reading database ... 202833 files and directories currently installed.) Removing ax88179 ... Error! There are no instances of module: ax88179_178a 1.6.0 located in the DKMS tree. rm: cannot remove ‘/usr/src/AX88179_178A_LINUX_DRIVER_v1.6.0_SOURCE’: No such file or directory dpkg: error processing ax88179 (--purge): subprocess installed pre-removal script returned error exit status 1 No apport report written because MaxReports is reached already ln: failed to create symbolic link ‘/usr/src/AX88179_178A_LINUX_DRIVER_v1.7.0_SOURCE’: File exists Error! DKMS tree already contains: ax88179_178a-1.7.0 You cannot add the same module/version combo more than once. Module ax88179_178a/1.7.0 already built for kernel 3.8.0-32-generic/4 Module ax88179_178a/1.7.0 already installed on kernel 3.8.0-32-generic/x86_64 Errors were encountered while processing: ax88179 E: Sub-process /usr/bin/dpkg returned an error code (1) It complains about both version 1.6 and 1.7. I've updated to 1.7 a couple of days ago. --force doesn't help either. I just want to get rid of it since when I'm running 3.11.6 the versions interfere with each other.

    Read the article

  • Grub menu not waiting despite of GRUB_TIMEOUT=10

    - by Optimus
    I have Ubuntu 12.04 installed along side of windows 7. The grub menu doesn't seem obey GRUB_TIMEOUT=10, I see the grub menu there for a split second and it immediately defaults to the first option. Grub menu worked fine when I first installed ubuntu. I am not able to pinpoint what exactly broke it(maybe some update?). I did resize my ubuntu partition using gparted but am not sure if that is what caused it. here are my settings from etc/default/grub GRUB_DEFAULT=0 #GRUB_HIDDEN_TIMEOUT=0 #GRUB_HIDDEN_TIMEOUT_QUIET=true GRUB_TIMEOUT=10 GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian` GRUB_CMDLINE_LINUX_DEFAULT="quiet splash" GRUB_CMDLINE_LINUX="" How do I fix this? Edit: As suggested by 'kamil' this is what I have tried so far with no luck - 1) hold the shift key while booting 2) sudo gedit /etc/default/grub edit GRUB_TIMEOUT to `GRUB_TIMEOUT=10` sudo update-grub 3) sudo gedit /etc/default/grub edit GRUB_TIMEOUT to `GRUB_TIMEOUT=10` sudo update-grub2 4) at the end of your /etc/grub.d/00_header file, comment out the if condition except for the regular set timeout line like this: #if [ \${recordfail} = 1 ]; then # set timeout=-1 #else set timeout=${GRUB_TIMEOUT} #fi then sudo update-grub and sudo update-grub2 5) install boot repair sudo add-apt-repository ppa:yannubuntu/boot-repair sudo apt-get update sudo apt-get install -y boot-repair boot-repair boot-repair output - Boot successfully repaired. ... The boot files of [The OS now in use - Ubuntu 12.04.1 LTS] are far from the start of the disk. Your BIOS may not detect them. You may want to retry after creating a /boot partition (EXT4, 200MB, start of the disk). This can be performed via tools such as gParted. Then select this partition via the [Separate /boot partition:] option of [Boot Repair]. (https://help.ubuntu.com/community/BootPartition) http://paste.ubuntu.com/1220468/ - here is the full boot-repair data Could grub files not being at the start of the disk create such issues?

    Read the article

  • Login Screen hangs after entering password

    - by Ravi
    When I enter my password in the login box nothing happens. It gets stuck. It was running fine earlier. I have installed gnome-panel and cairo-dock, after which, I logged out, logged back in, and choose gnome classic session. I also added a ppa from the webupd8.org to install the themes (link). I opened Ubuntu Tweak tool, and changed the theme to Evolve the whole laptop stopped responding. The keyboard and mouse were unresponsive. So I was forced to do a shut down. Now whenever it starts, I cannot login into Ubuntu. I hear the fan noise, as its spinning very fast, when the laptop freezes.(Probably the CPU is running at 100%). Please help me. How can I login back to Ubuntu? I am using Ubuntu 12.04 and have installed all the latest updates.. EDIT: I want to know how can I delete a folder from the file system using the live CD?

    Read the article

< Previous Page | 18 19 20 21 22 23 24  | Next Page >