Search Results

Search found 19446 results on 778 pages for 'network printer'.

Page 221/778 | < Previous Page | 217 218 219 220 221 222 223 224 225 226 227 228  | Next Page >

  • Windows 7 Users unable to add Windows 2003 server printers

    - by TravBrack
    Hi there I just rolled out a few Windows 7 x64 machines and ran into this issue where non-admin users are unable to add printers hosted on a windows 2003 server. It works fine on a 2008 server. The issue appears to be with the point and print system. A user will attempt to add the printer, a prompt will come up requiring the user to elevate privileges in order to install a driver, and will fail citing 'access denied'. I found the group policy setting Point and Print Restrictions: When the policy setting is disabled: -Windows Vista computers will not show a warning or an elevated command prompt when users create a printer connection to any server using Point and Print. So I disabled it, verified that the policy was being picked up using rsop, but it still does the same thing. I've also tried the following: Recreating the printers using newer drivers Adding the printer using 32 bit drivers on the 2003 machine, then adding the 64 bit drivers on a Windows 7 machine Adding the printer from a windows 7 machine using print management None of these things work. The security settings are no different than the working printers. Help?

    Read the article

  • Getting Win32_Service security descriptor using VBScript

    - by invictus
    Hi, I am using VbScript for retrieving the securitydescriptor of a Win32_Service. I am using the following code: SE_DACL_PRESENT = &h4 ACCESS_ALLOWED_ACE_TYPE = &h0 ACCESS_DENIED_ACE_TYPE = &h1 strComputer = "." Set objWMIService = GetObject("winmgmts:" _ & "{impersonationLevel=impersonate, (Security)}!\\" & strComputer & "\root\cimv2") Set colInstalledPrinters = objWMIService.ExecQuery _ ("Select * from Win32_Service") For Each objPrinter in colInstalledPrinters Wscript.Echo "Name: " & objPrinter.Name ' Get security descriptor for printer Return = objPrinter.GetSecurityDescriptor( objSD ) If ( return <> 0 ) Then WScript.Echo "Could not get security descriptor: " & Return wscript.Quit Return End If ' Extract the security descriptor flags intControlFlags = objSD.ControlFlags If intControlFlags AND SE_DACL_PRESENT Then ' Get the ACE entries from security descriptor colACEs = objSD.DACL For Each objACE in colACEs ' Get all the trustees and determine which have access to printer WScript.Echo objACE.Trustee.Domain & "\" & objACE.Trustee.Name If objACE.AceType = ACCESS_ALLOWED_ACE_TYPE Then WScript.Echo vbTab & "User has access to printer" ElseIf objACE.AceType = ACCESS_DENIED_ACE_TYPE Then WScript.Echo vbTab & "User does not have access to the printer" End If Next Else WScript.Echo "No DACL found in security descriptor" End If Next However, every time I run it I get the message saying the resulting code is -2165236532 something, rather than the error codes defined in the manual. Anyone got any ideas? I am using Windows 7 professional.

    Read the article

  • Print over remote CUPS server, but just show a subset of the printers.

    - by jdm
    I'd like to print from my Ubuntu laptop (karmic) to some networked printers. Our organisation uses a CUPS server with several hundred printers. What I know I can do is: CUPS_SERVER=printers.company.com acroread document.pdf and then Adobe Reader shows me all available printers to select from. However, it takes a couple of minutes to display the large list, which is really annoying. (The desktop PCs here suffer from this, too.) The other option is to add a new printer with an address like ipp://printers.company.com/printer/bldg1_hp8150 (to the Ubuntu printer configuration = local CUPS server). However, it asks me for a driver. I don't want to / can't always specify a driver, since some printers don't appear in the list. I'd like to let the remote CUPS server handle the driver part (like it does when i set CUPS_SERVER), and do no more preprocessing/"driver stuff" on my side. The ideal thing would be if I could somehow add the remote printer list to my local cups server, and apply a filter, so that it would just display printers a la bldg1_*. This feature was available in KDE3.?, but I can't find something similar in Ubuntu/Gnome. Any suggestions?

    Read the article

  • NIC Bonding/balance-rr with Dell PowerConnect 5324

    - by Branden Martin
    I'm trying to get NIC bonding to work with balance-rr so that three NIC ports are combined, so that instead of getting 1 Gbps we get 3 Gbps. We are doing this on two servers connected to the same switch. However, we're only getting the speed of one physical link. We are using 1 Dell PowerConnect 5324, SW version 2.0.1.3, Boot version 1.0.2.02, HW version 00.00.02. Both servers are CentOS 5.9 (Final) running OnApp Hypervisor (CloudBoot) Server 1 is using ports g5-g7 in port-channel 1. Server 2 is using ports g9-g11 in port-channel 2. Switch show interface status Port Type Duplex Speed Neg ctrl State Pressure Mode -------- ------------ ------ ----- -------- ---- ----------- -------- ------- g1 1G-Copper -- -- -- -- Down -- -- g2 1G-Copper Full 1000 Enabled Off Up Disabled Off g3 1G-Copper -- -- -- -- Down -- -- g4 1G-Copper -- -- -- -- Down -- -- g5 1G-Copper Full 1000 Enabled Off Up Disabled Off g6 1G-Copper Full 1000 Enabled Off Up Disabled Off g7 1G-Copper Full 1000 Enabled Off Up Disabled On g8 1G-Copper Full 1000 Enabled Off Up Disabled Off g9 1G-Copper Full 1000 Enabled Off Up Disabled On g10 1G-Copper Full 1000 Enabled Off Up Disabled On g11 1G-Copper Full 1000 Enabled Off Up Disabled Off g12 1G-Copper Full 1000 Enabled Off Up Disabled On g13 1G-Copper -- -- -- -- Down -- -- g14 1G-Copper -- -- -- -- Down -- -- g15 1G-Copper -- -- -- -- Down -- -- g16 1G-Copper -- -- -- -- Down -- -- g17 1G-Copper -- -- -- -- Down -- -- g18 1G-Copper -- -- -- -- Down -- -- g19 1G-Copper -- -- -- -- Down -- -- g20 1G-Copper -- -- -- -- Down -- -- g21 1G-Combo-C -- -- -- -- Down -- -- g22 1G-Combo-C -- -- -- -- Down -- -- g23 1G-Combo-C -- -- -- -- Down -- -- g24 1G-Combo-C Full 100 Enabled Off Up Disabled On Flow Link Ch Type Duplex Speed Neg control State -------- ------- ------ ----- -------- ------- ----------- ch1 1G Full 1000 Enabled Off Up ch2 1G Full 1000 Enabled Off Up ch3 -- -- -- -- -- Not Present ch4 -- -- -- -- -- Not Present ch5 -- -- -- -- -- Not Present ch6 -- -- -- -- -- Not Present ch7 -- -- -- -- -- Not Present ch8 -- -- -- -- -- Not Present Server 1: cat /etc/sysconfig/network-scripts/ifcfg-eth3 DEVICE=eth3 HWADDR=00:1b:21:ac:d5:55 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth4 DEVICE=eth4 HWADDR=68:05:ca:18:28:ae USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth5 DEVICE=eth5 HWADDR=68:05:ca:18:28:af USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-onappstorebond DEVICE=onappstorebond IPADDR=10.200.52.1 NETMASK=255.255.0.0 GATEWAY=10.200.2.254 NETWORK=10.200.0.0 USERCTL=no BOOTPROTO=none ONBOOT=yes cat /proc/net/bonding/onappstorebond Ethernet Channel Bonding Driver: v3.4.0-1 (October 7, 2008) Bonding Mode: load balancing (round-robin) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth3 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 00:1b:21:ac:d5:55 Slave Interface: eth4 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:28:ae Slave Interface: eth5 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:28:af Server 2: cat /etc/sysconfig/network-scripts/ifcfg-eth3 DEVICE=eth3 HWADDR=00:1b:21:ac:d5:a7 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth4 DEVICE=eth4 HWADDR=68:05:ca:18:30:30 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth5 DEVICE=eth5 HWADDR=68:05:ca:18:30:31 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-onappstorebond DEVICE=onappstorebond IPADDR=10.200.53.1 NETMASK=255.255.0.0 GATEWAY=10.200.3.254 NETWORK=10.200.0.0 USERCTL=no BOOTPROTO=none ONBOOT=yes cat /proc/net/bonding/onappstorebond Ethernet Channel Bonding Driver: v3.4.0-1 (October 7, 2008) Bonding Mode: load balancing (round-robin) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth3 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 00:1b:21:ac:d5:a7 Slave Interface: eth4 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:30:30 Slave Interface: eth5 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:30:31 Here are the results of iperf. ------------------------------------------------------------ Client connecting to 10.200.52.1, TCP port 5001 TCP window size: 27.7 KByte (default) ------------------------------------------------------------ [ 3] local 10.200.3.254 port 53766 connected with 10.200.52.1 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 950 MBytes 794 Mbits/sec

    Read the article

  • iPhone doesn't save password for Cisco IPsec VPN using racoon daemon

    - by dsx
    On my Debian server I had set up racoon daemon (1:0.8.0-14) for Cisco IPSec VPN using certificates for authentication. My racoon.conf is like following: log info; path certificate "/etc/racoon/certs"; listen { isakmp $SERVER_IP_HERE [500]; isakmp_natt $SERVER_IP_HERE [4500]; } timer { natt_keepalive 10 sec; } remote anonymous { lifetime time 24 hours; proposal_check obey; passive on; exchange_mode aggressive,main; my_identifier asn1dn; peers_identifier asn1dn; verify_identifier on; certificate_type x509 "cert_name.crt" "key_name.key"; ca_type x509 "ca.crt"; mode_cfg on; verify_cert on; ike_frag on; generate_policy on; nat_traversal on; dpd_delay 20; proposal { encryption_algorithm aes; hash_algorithm sha1; authentication_method xauth_rsa_server; dh_group modp1024; } } mode_cfg { conf_source local; auth_source system; auth_throttle 3; save_passwd on; dns4 8.8.8.8; network4 $SOME_LAN_SUBNET; netmask4 255.255.255.0; pool_size 128; } sainfo anonymous { pfs_group 2; lifetime time 24 hour; encryption_algorithm aes; authentication_algorithm hmac_sha1; compression_algorithm deflate; } I'm not using PSK authentication here. Using iPhone configuration utility I had uploaded all required certificates to iPhone and set up VPN on demand. Everything works just fine except one thing: iPhone refuses to save VPN password regardless of save_passwd on; in racoon configuration file. As opposed to iPhone behaviour, Mac OS X 10.8.2 have no problems saving password. I had examined iPhone log file and found following: racoon[151] <Notice>: >>>>> phase change status = phase 1 established configd[50] <Notice>: IPSec Network Configuration started. configd[50] <Notice>: IPSec Network Configuration: INTERNAL-IP4-ADDRESS = $SUBNET_IP_HERE. configd[50] <Notice>: IPSec Network Configuration: INTERNAL-IP4-MASK = 255.255.255.0. configd[50] <Notice>: IPSec Network Configuration: SAVE-PASSWORD = 0. configd[50] <Notice>: IPSec Network Configuration: INTERNAL-IP4-DNS = 8.8.8.8. configd[50] <Notice>: IPSec Network Configuration: BANNER = . configd[50] <Notice>: IPSec Network Configuration: DEF-DOMAIN = . configd[50] <Notice>: IPSec Network Configuration: DEFAULT-ROUTE = local-address $SUBNET_IP_HERE/32. configd[50] <Notice>: IPSec Phase2 starting. configd[50] <Notice>: IPSec Network Configuration established. configd[50] <Notice>: IPSec Phase1 established. Please note IPSec Network Configuration message containing SAVE-PASSWORD = 0.. Is it a bug in racoon daemon on server, or iPhone (iOS version is 6.0.1 (10A523)) or it is me missing something? How to make iPhone remember IPSec VPN password?

    Read the article

  • IPv6: Should I have private addresses?

    - by AlReece45
    Right now, we have a rack of servers. Every server right now has at least 2 IP addresses, one for the public interface, another for the private. The servers that have SSL websites on them have more IP addresses. We also have virtual servers, that are configured similarly. Private Network The private range is currently just used for backups and monitoring. Its a gigabit port, the interface usage does not usually get very high. There are other technologies we're considering using that would use this port: iSCSI (implementations usually recommends dedicating an interface to it, which would be yet another IP network), VPN to get access to the private range (something I'd rather avoid) dedicated database servers LDAP centralized configuration (like puppet) centralized logging We don't have any private addresses in our DNS records (only public addresses). For our servers to utilize the correct IP address for the right interface (and not hard code the IP address) probably requires setting up a private DNS server (So now we add 2 different dns entries to 2 different systems). Public Network Our public range has a variety of services include web, email, and ftp. There is a hardware firewall between our network and the "public" network. We have (relatively secure) method to instruct the firewall to open and close administrative access (web interfaces, ssh, etc) for our current IP address. With either solution discussed, the host-based firewalls will be configured as well. The public network currently runs at a dedicated 20Mbps link. There are a couple of legacy servers with fast-ethernet ports, but they are scheduled for decommissioning. All of the other production boxes have at least 2 Gigabit Ethernet ports. The more traffic-heavy servers have 4-6 available (none is using more than the 2 Gigabit ports right now). IPv6 I want to get an IPv6 prefix from our ISP. So at least every "server" has at least one IPv6 interface. We'll still need to keep the IPv4 addressees up and available for legacy clients (web servers and email at the very least). We have two IP networks right now. Adding the public IPv6 address would make it three. Just use IPv6? I'm thinking about just dumping the private IPv4 range and using the IPv6 range as the primary means of all communications. If an interface starts reaching its capacity, utilize the newly free interfaces to create a trunk. It has the advantage that if either the public or private traffic needs to exceed 1Gbps. The traffic for each interface is already analyzed on a regular basis to predict future bandwidth use. In the rare instances where bandwidth unexpected peaks: utilize QoS to ensure traffic (like our limited SSH access) is prioritized correctly so the problem can be corrected (if possible, our WAN is the bottleneck right now). It also has the advantage of not needing to make an entry for every private address. We may have private DNS (or just LDAP), but it'll be much more limited in scope with less entries to duplicate. Summary I'm trying to make this network as "simple" as possible. At the same time, I want to make sure its reliable, upgradeable, scalable, and (eventually) redundant. Having one IPv6 network, and a legacy IPv4 network seems to be the best solution to me. Regarding using assigned IPv6 addresses for both networks, sharing the available bandwidth on one (more trunked if needed): Are there any technical disadvantages (limitations, buffers, scalability)? Are there any other security considerations (asides from firewalls mentioned above) to consider? Are there regulations or other security requirements (like PCI-DSS) that this doesn't meet? Is there typical software for setting up a Linux network that doesn't have IPv6 support yet? (logging, ldap, puppet) Some other thing I didn't consider?

    Read the article

  • Ubuntu Server, 2 Ethernet Devices, Same Gateway - Want to force internet traffic through 1 device (or at least allow it to work!)

    - by Chris Drumgoole
    I have a Ubuntu 10.04 Server with 2 ethernet devices, eth0 and eth1. eth0 has a static IP of 192.168.1.210 eth1 has a static IP if 192.168.1.211 The DHCP server (which also serves as the internet gateway) sits at 192.168.1.1. The issue I have right now is when I have both plugged in, I can connect to both IPs over SSH internally, but I can't connect to the internet from the server. If I unplug one of the devices (e.g. eth1), then it works, no problem. (Also, I get the same result when I run sudo ifconfig eth1 down). Question, how can I configure it so that I can have both devices eth0 and eth1 play nice on the same network, but allow internet access as well? (I am open to either enforcing all inet traffic going through a single device, or through both, I'm flexible). From my google searching, it seems I could have a unique (or not popular) problem, so haven't been able to find a solution. Is this something that people generally don't do? The reason I want to make use of both ethernet devices is because I want to run different local traffic services on on both to split the load, so to speak... Thanks in advance. UPDATE Contents of /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp # The secondary network interface #auto eth1 #iface eth1 inet dhcp (Note: above, I commented out the last 2 lines because I thought that was causing issues... but it didn't solve it) netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.1.0 192.168.1.1 255.255.255.0 UG 0 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 UPDATE 2 I made a change to the /etc/network/interfaces file as suggested by Kevin. Before I display the file contents and the route table, when I am logged into the server (through SSH), I can not ping an external server, so this is the same issue I was experiencing that led to me posting this question. I ran a /etc/init.d/networking restart after making the file changes. Contents of /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp address 192.168.1.210 netmask 255.255.255.0 gateway 192.168.1.1 # The secondary network interface auto eth1 iface eth1 inet dhcp address 192.168.1.211 netmask 255.255.255.0 ifconfig output eth0 Link encap:Ethernet HWaddr 78:2b:cb:4c:02:7f inet addr:192.168.1.210 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::7a2b:cbff:fe4c:27f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6397 errors:0 dropped:0 overruns:0 frame:0 TX packets:683 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:538881 (538.8 KB) TX bytes:85597 (85.5 KB) Interrupt:36 Memory:da000000-da012800 eth1 Link encap:Ethernet HWaddr 78:2b:cb:4c:02:80 inet addr:192.168.1.211 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::7a2b:cbff:fe4c:280/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5799 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:484436 (484.4 KB) TX bytes:1184 (1.1 KB) Interrupt:48 Memory:dc000000-dc012800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:635 errors:0 dropped:0 overruns:0 frame:0 TX packets:635 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:38154 (38.1 KB) TX bytes:38154 (38.1 KB) netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0

    Read the article

  • My ASP.NET news sources

    - by Jon Galloway
    I just posted about the ASP.NET Daily Community Spotlight. I was going to list a bunch of my news sources at the end, but figured this deserves a separate post. I've been following a lot of development blogs for a long time - for a while I subscribed to over 1500 feeds and read them all. That doesn't scale very well, though, and it's really time consuming. Since the community spotlight requires an interesting ASP.NET post every day of the year, I've come up with a few sources of ASP.NET news. Top Link Blogs Chris Alcock's The Morning Brew is a must-read blog which highlights each day's best blog posts across the .NET community. He covers the entire Microsoft development, but generally any of the top ASP.NET posts I see either have already been listed on The Morning Brew or will be there soon. Elijah Manor posts a lot of great content, which is available in his Twitter feed at @elijahmanor, on his Delicious feed, and on a dedicated website - Web Dev Tweets. While not 100% ASP.NET focused, I've been appreciating Joe Stagner's Weekly Links series, partly since he includes a lot of links that don't show up on my other lists. Twitter Over the past few years, I've been getting more and more of my information from my Twitter network (as opposed to RSS or other means). Twitter is as good as your network, so if getting good information off Twitter sounds crazy, you're probably not following the right people. I already mentioned Elijah Manor (@elijahmanor). I follow over a thousand people on Twitter, so I'm not going to try to pick and choose a list, but one good way to get started building out a Twitter network is to follow active Twitter users on the ASP.NET team at Microsoft: @scottgu (well, not on the ASP.NET team, but their great grand boss, and always a great source of ASP.NET info) @shanselman @haacked @bradwilson @davidfowl @InfinitiesLoop @davidebbo @marcind @DamianEdwards @stevensanderson @bleroy @humancompiler @osbornm @anurse I'm sure I'm missing a few, and I'll update the list. Building a Twitter network that follows topics you're interested in allows you to use other tools like Cadmus to automatically summarize top content by leveraging the collective input of many users. Twitter Search with Topsy You can search Twitter for hashtags (like #aspnet, #aspnetmvc, and #webmatrix) to get a raw view of what people are talking about on Twitter. Twitter's search is pretty poor; I prefer Topsy. Here's an example search for the #aspnetmvc hashtag: http://topsy.com/s?q=%23aspnetmvc You can also do combined queries for several tags: http://topsy.com/s?q=%23aspnetmvc+OR+%23aspnet+OR+%23webmatrix Paper.li Paper.li is a handy service that builds a custom daily newspaper based on your social network. They've turned a lot of people off by automatically tweeting "The SuperDevFoo Daily is out!!!" messages (which can be turned off), but if you're ignoring them because of those message, you're missing out on a handy, free service. My paper.li page includes content across a lot of interests, including ASP.NET: http://paper.li/jongalloway When I want to drill into a specific tag, though, I'll just look at the Paper.li post for that hashtag. For example, here's the #aspnetmvc paper.li page: http://paper.li/tag/aspnetmvc Delicious I mentioned previously that I use Delicious for managing site links. I also use their network and search features. The tag based search is pretty good: Even better, though, is that I can see who's bookmarked these links, and add them to my Delicious network. After having built out a network, I can optimize by doing less searching and more leaching leveraging of collective intelligence. Community Sites I scan DotNetKicks, the weblogs.asp.net combined feed, and the ASP.NET Community page, CodeBetter, Los Techies,  CodeProject,  and DotNetSlackers from time to time. They're hit and miss, but they do offer more of an opportunity for finding original content which others may have missed. Terms of Enrampagement When someone's on a tear, I just manually check their sites more often. I could use RSS for that, but it changes pretty often. I just keep a mental note of people who are cranking out a lot of good content and check their sites more often. What works for you?

    Read the article

  • Xsigo and Oracle's Storage

    - by Philippe Deverchère
    Xsigo, a virtual network infrastructure provider, has recently been acquired by Oracle. Following this acquisition, one might ask ourselves why it is important to Oracle and how Oracle's storage is going to benefit on the long term from this virtualized infrastructure layer. Well, the first thing to understand is that Virtual Networking addresses both network and storage connectivity. Oracle Virtual Networking, as the Xsigo technology is now called, connects any server to any network and storage, so this is not just about connecting servers to the Internet or Intranet. It is also for a large part connecting servers to NAS and SAN storage. Connecting servers to storage has become increasingly complex in the past few years because of the strong emergence of virtualization at the Operating System level. 50% of enterprise workloads are now virtualized, up from 18% in 2009, resulting in a strong consolidation of various applications in a high density server footprint. At the same time, server I/O capability increased 8x in the last 8 years. All this has pushed IT administrators to multiply the number of I/O connections in the back-end of their physical servers, resulting in a messy and very hard to manage networking infrastructure. Here is a typical view of a rack back-end when no virtual networking is used. We consider that today: - 75% of users have ten or more Ethernet ports per server - 85% of users have two or more SAN ports per server - 58% have had to add connectivity to a server specifically for VMs - 65% consider cable reduction a priority The average is 12 or more ports per server, resulting in an extremely complex infrastructure to manage. What Oracle wants to achieve with its Oracle Virtual Networking offering is pretty simple. The objective is to eliminate the complexity through a dramatic reduction of cabling between servers and storage/networks. It is also to provide a software based management system so that any server can be connected to any network or any storage, on demand, and without physical intervention on the infrastructure. At the end of the day, the picture on the left shows what one wants to get for the back-end of customer's racks: just a couple of connections on each physical server to provide a simple, agile and fast network infrastructure for both storage and networking access. This is exactly what the Oracle Virtual Networking solution does. It transforms a complex, error-prone, difficult to manage and expensive networking infrastructure into a simple, high performance and agile solution for the data center. Practically speaking, and for the sake of simplicity, imagine that each server just hosts a minimal number of physical InfiniBand HCAs (Host Channel Adapter) with two links (for redundancy) onto the Oracle Fabric Interconnect director. Using the Oracle Fabric Manager software, you'll then be able to create virtual NICs and HBAs (called vNIC and vHBA) that will be seen by the servers as standard NICs and HBAs and associate them to networks and storage systems which are physically connected to the back-end of the director through standard Fibre Channel and Ethernet GbE/10GbE ports. In addition to this incredibly simple "at-a-click" connectivity capability, the Oracle Virtual Networking solution offers powerful features such as network isolation, Quality of Service, advanced performance monitoring and non-disruptive reconfiguration, migration and scalability of networking infrastructure. So let's go back now to our initial question: why is Oracle Virtual Networking especially important to Oracle's storage solutions? After all, one could connect any storage in the back-end of the Oracle Fabric Interconnect directors, right? The answer is pretty simple: since Oracle owns both the virtualized networking infrastructure and the storage (ZFS-SA, Pillar Axiom and tape), it is possible to imagine several ways in the future to add value when it comes to connect storage to a virtualized storage network: enhanced storage capabilities, converged management between storage and network, improved diagnostic capabilities and optimized integration resulting in higher performance and unique features/functions. Of course, all this is not going to be done overnight, and future will tell us is which evolutions come first. But there is little doubt that the integration of Xsigo within Oracle is going to create opportunities for Oracle's storage!

    Read the article

  • My LAN USB NIC is not working in ubuntu 11.10?

    - by Gaurav_Java
    Today i start my system its seems that my LAN port is not working . so i buy one USB to LAN adapter and i plug in ubuntu system its doen't connect automatically .when i check result lsusb its shows me that there is one DM9601 Ethernet adapter is connected when i click on network information in panel its shows me that there is something " wired NEtwork (Broadcom NetLink BCM5784M gigabit Ethernet PCIe) I think want some driver for that .i don't have any idea how it can be used ? here output of sudo lspci -nn *00:00.0 Host bridge [0600]: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub [8086:2a40] (rev 07) 00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a42] (rev 07) 00:02.1 Display controller [0380]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a43] (rev 07) 00:1a.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 [8086:2937] (rev 03) 00:1a.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 [8086:2938] (rev 03) 00:1a.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 [8086:293c] (rev 03) 00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio Controller [8086:293e] (rev 03) 00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 [8086:2940] (rev 03) 00:1c.1 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 [8086:2942] (rev 03) 00:1c.2 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 [8086:2944] (rev 03) 00:1c.4 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 [8086:2948] (rev 03) 00:1d.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 [8086:2934] (rev 03) 00:1d.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 [8086:2935] (rev 03) 00:1d.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 [8086:2936] (rev 03) 00:1d.3 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 [8086:2939] (rev 03) 00:1d.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 [8086:293a] (rev 03) 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev 93) 00:1f.0 ISA bridge [0601]: Intel Corporation ICH9M LPC Interface Controller [8086:2919] (rev 03) 00:1f.2 SATA controller [0106]: Intel Corporation ICH9M/M-E SATA AHCI Controller [8086:2929] (rev 03) 00:1f.3 SMBus [0c05]: Intel Corporation 82801I (ICH9 Family) SMBus Controller [8086:2930] (rev 03) 02:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5784M Gigabit Ethernet PCIe [14e4:1698] (rev 10) 04:00.0 Network controller [0280]: Intel Corporation WiFi Link 5100 [8086:4232]* sudo lshw -class network *-network description: Ethernet interface product: NetLink BCM5784M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 10 serial: 00:1f:16:9a:56:98 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 firmware=sb v2.19 latency=0 link=no multicast=yes port=twisted pair resources: irq:47 memory:f4500000-f450ffff *-network DISABLED description: Wireless interface product: WiFi Link 5100 vendor: Intel Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 00 serial: 00:22:fa:09:02:00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-17-generic firmware=8.83.5.1 build 33692 latency=0 link=no multicast=yes wireless=IEEE 802.11abgn resources: irq:46 memory:f4600000-f4601fff *-network description: Ethernet interface physical id: 4 logical name: eth1 serial: 00:60:6e:00:f1:7d size: 100Mbit/s capacity: 100Mbit/s capabilities: ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=dm9601 driverversion=22-Aug-2005 duplex=full firmware=Davicom DM9601 USB Ethernet ip=192.168.1.34 link=yes multicast=yes port=MII speed=100Mbit/s I am using Wimax internet connection which i have to connect from browser . at that time my system is not showing that i am connected to any wired connection. but when i connect internet from other system after getting conneted to internet . when i plug again my USB LAN then its shows that you are conneted to wired connetion. here is screenshot for conneting wimax from browser after connecting to internet network connection shows

    Read the article

  • 6 Reasons Why You Can’t Move Your Cell Phone To Any Carrier You Want

    - by Chris Hoffman
    You can buy a laptop or Wi-Fi tablet and use it on Wi-Fi anywhere in the world, so why are cell phones and devices with mobile data not portable between different cellular networks in the same country? Unlike with Wi-Fi, there are many different competing cellular network standards — both around the world and within countries. Cellular carriers also like locking you to their specific network and making it difficult to move. That’s what contracts are for. Phone Locking Many phones are sold locked to a specific network. When you buy a phone from a cellular carrier, they often lock that phone to their network so you can’t take it to a competitor’s network. That’s why you’ll often need to unlock a phone before you can move it to a different cellular provider or take it to a different country and use it on a local provider instead of roaming. Cellular carriers will generally unlock your phone for you as long as you’re no longer in a contract with them. However, unlocking a cell phone you’ve paid for without your carrier’s permission is currently a crime in the USA. GSM vs. CDMA Some cellular networks use the GSM (Global System for Mobile Communications) standard, while some use CDMA (Code-division multiple access). Worldwide, most cellular networks use GSM. In the USA, both GSM and CDMA are popular. Verizon, Sprint, and other carriers that use their networks use CDMA. AT&T, T-Mobile, and other carriers that use their networks are use GSM. These are two competing standards and are not interoperable. This means you can’t simply take a phone from Verizon to T-Mobile, or from AT&T to Sprint. These carriers have incompatible phones. CDMA Restrictions CDMA is more restricted than GSM. GSM phones have SIM cards. Simply open the phone, pop out the SIM card, and pop in a new SIM card to switch carriers. (In reality, it’s more complicated thanks to phone locking and other factors here.) CDMA phones don’t have removable modules like this. All CDMA phones ship locked to a specific network and you’d have to get both your old carrier and your new carrier to cooperate to switch phones between them. In reality, many people just consider CDMA phones eternally locked to a specific carrier. Frequencies Different cellular networks throughout the USA and the rest of the world use different frequencies. These radio frequencies have to be supported by your phone’s hardware or your phone simply can’t work on a network using those frequencies. Many GSM phones support three or four bands of frequencies — 900/1800/1900 MHz, 850/1800/1900 MHz, or 850/900/1800/1900 MHz. These are sometimes called “world phones” because they allow easier roaming. This allows the manufacturer to produce a phone that will support all GSM networks in the world and allows their customers to travel with those phones. If your phone doesn’t support the appropriate frequencies, it won’t work on certain networks. LTE Bands When it comes to newer, faster LTE networks, different frequencies are still a concern. LTE frequencies are generally known as “LTE bands.” To use a smartphone on a certain LTE network, that smartphone will have to support that LTE network’s frequency. Different models of phones are often created to work on different LTE networks around the world. However, phones are generally supporting more and more LTE networks and becoming more and more interoperable over time. SIM Card Sizes The SIM cards used in GSM phones come in different sizes. Newer phones use smaller SIM cards to save space and be more compact. This isn’t a big obstacle, as the different sizes of SIM cards — full-size SIM, mini-SIM, micro-SIM, and nano-SIM are actually compatible. The only difference between them is the size of the plastic card surrounding the SIM’s chip. The actual chip is the same size between all the SIM cards. This means you can take an old SIM card and cut the plastic off until it becomes a smaller-size SIM card that fits in a modern phone. Or, you can take a smaller-size SIM card and insert it into a tray so that it becomes a larger-size SIM card that fits in an older phone. Be aware that it’s very possible to damage your SIM card and make it not work properly by cutting it to the wrong dimensions. Your cellular carrier will often be able to cut your SIM card for you or give you a new one if you want to use an old SIM card in a new phone. Hopefully they won’t overcharge you for this service, too. Be sure to check what types of networks, frequencies, and LTE bands your phone supports before trying to move it between networks. You may have to buy a new phone when moving between certain cellular carriers. Image Credit: Morgan on Flickr, 22n on Flickr

    Read the article

  • Configure IPv6 on your Linux system (Ubuntu)

    After the presentation on IPv6 at the first event of the Emtel Knowledge Series and some recent discussion on social media networks with other geeks and Linux interested IT people here in Mauritius, I thought that I should give it a try (finally) and tweak my local network infrastructure. Honestly, I have been to busy with contractual project work and it never really occurred to me to set up IPv6 in my LAN. Well, the following paragraphs are going to shed some light on those aspects of modern computer and network technology. This is the first article in a series on IPv6 configuration: Configure IPv6 on your Linux system DHCPv6: Provide IPv6 information in your local network Enabling DNS for IPv6 infrastructure Accessing your web server via IPv6 Piece of advice: This is based on my findings on the internet while reading other people's helpful articles and going through a couple of man-pages on my local system. Let's embrace IPv6 The basic configuration on Linux is actually very simple as the kernel, operating system, and user-space programs support that protocol natively. If your system is ready to go for IP (aka: IPv4), then you are good to go for anything else. At least, I didn't have to install any additional packages on my system(s). We are going to assign a static IPv6 address to the system. Hence, we have to modify the definition of interfaces and check whether we have an inet6 entry specified. Open your favourite text editor and check the following entries (it should be at least similar to this): $ sudo nano /etc/network/interfaces auto eth0# IPv4 configurationiface eth0 inet static  address 192.168.1.2  network 192.168.1.0  netmask 255.255.255.0  broadcast 192.168.1.255# IPv6 configurationiface eth0 inet6 static  pre-up modprobe ipv6  address 2001:db8:bad:a55::2  netmask 64 Of course, you might have to adjust your interface device (eth0) or you might be interested to have multiple directives for additional devices (eth1, eth2, etc.). The auto instruction takes care that your device is enabled and configured during the booting phase. The use of the pre-up directive depends on your kernel configuration but in most scenarios this might be an optional line. Anyways, it doesn't hurt to have it enabled after all - just to be on the safe side. Next, either restart your network subsystem like so: $ sudo service networking restart Or you might prefer to do it manually with identical parameters, like so: $ sudo ifconfig eth0 inet6 add 2001:db8:bad:a55::2/64 In case that you're logged in remotely into your PC (ie. via ssh), it is highly advised to opt for the second choice and add the device manually. You can check your configuration afterwards with one of the following commands (depends on whether it is installed): $ sudo ifconfig eth0eth0      Link encap:Ethernet  HWaddr 00:21:5a:50:d7:94            inet addr:192.168.160.2  Bcast:192.168.160.255  Mask:255.255.255.0          inet6 addr: fe80::221:5aff:fe50:d794/64 Scope:Link          inet6 addr: 2001:db8:bad:a55::2/64 Scope:Global          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1 $ sudo ip -6 address show eth03: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000    inet6 2001:db8:bad:a55::2/64 scope global        valid_lft forever preferred_lft forever    inet6 fe80::221:5aff:fe50:d794/64 scope link        valid_lft forever preferred_lft forever In both cases, it confirms that our network device has been assigned a valid IPv6 address. That's it in general for your setup on one system. But of course, you might be interested to enable more services for IPv6, especially if you're already running a couple of them in your IP network. More details are available on the official Ubuntu Wiki. Continue to configure your network to provide IPv6 address information automatically in your local infrastructure.

    Read the article

  • Mouse takes a while to start working after boot

    - by warkior
    I just recently installed Ubuntu 12.04 (64 bit) and a number of my USB devices have stopped working. At least, they don't work for the first 3-5 minutes. I have two mice (one wireless, one wired) and a camera, which seem to take Ubuntu 3-5 minutes to recognize after booting up. Eventually, they do start to work, but it takes ages! lsusb results: (when the mice are working...) $ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 046d:c512 Logitech, Inc. LX-700 Cordless Desktop Receiver Bus 003 Device 003: ID 03f0:3f11 Hewlett-Packard PSC-1315/PSC-1317 Bus 006 Device 002: ID 046d:c00c Logitech, Inc. Optical Wheel Mouse Bus 006 Device 003: ID 046d:c52b Logitech, Inc. Unifying Receiver syslog entries for what seems (to my very untrained eye) to be the problem: Oct 12 20:12:51 REMOVED-GA-MA785GM-US2H kernel: [ 17.420117] usb 2-3: device descriptor read/64, error -110 Oct 12 20:12:57 REMOVED-GA-MA785GM-US2H goa[1879]: goa-daemon version 3.4.0 starting [main.c:112, main()] Oct 12 20:13:06 REMOVED-GA-MA785GM-US2H kernel: [ 32.636107] usb 2-3: device descriptor read/64, error -110 Oct 12 20:13:06 REMOVED-GA-MA785GM-US2H kernel: [ 32.852122] usb 2-3: new high-speed USB device number 3 using ehci_hcd Oct 12 20:13:21 REMOVED-GA-MA785GM-US2H kernel: [ 47.964131] usb 2-3: device descriptor read/64, error -110 Oct 12 20:13:37 REMOVED-GA-MA785GM-US2H kernel: [ 63.180115] usb 2-3: device descriptor read/64, error -110 Oct 12 20:13:37 REMOVED-GA-MA785GM-US2H kernel: [ 63.396126] usb 2-3: new high-speed USB device number 4 using ehci_hcd Oct 12 20:13:47 REMOVED-GA-MA785GM-US2H kernel: [ 73.804158] usb 2-3: device not accepting address 4, error -110 Oct 12 20:13:47 REMOVED-GA-MA785GM-US2H kernel: [ 73.916190] usb 2-3: new high-speed USB device number 5 using ehci_hcd Oct 12 20:13:58 REMOVED-GA-MA785GM-US2H kernel: [ 84.324160] usb 2-3: device not accepting address 5, error -110 Oct 12 20:13:58 REMOVED-GA-MA785GM-US2H kernel: [ 84.324197] hub 2-0:1.0: unable to enumerate USB device on port 3 Oct 12 20:13:58 REMOVED-GA-MA785GM-US2H udev-configure-printer: failed to claim interface Oct 12 20:13:58 REMOVED-GA-MA785GM-US2H udev-configure-printer: Failed to get parent Oct 12 20:13:58 REMOVED-GA-MA785GM-US2H udev-configure-printer: device devpath is /devices/pci0000:00/0000:00:12.0/usb3/3-3 Oct 12 20:13:58 REMOVED-GA-MA785GM-US2H udev-configure-printer: MFG:hp MDL:psc 1310 series SERN:CN47CB60BJO2 serial:CN47CB60BJO2 Oct 12 20:13:58 REMOVED-GA-MA785GM-US2H kernel: [ 84.768132] usb 5-3: new full-speed USB device number 2 using ohci_hcd Oct 12 20:14:01 REMOVED-GA-MA785GM-US2H udev-configure-printer: no corresponding CUPS device found Oct 12 20:14:13 REMOVED-GA-MA785GM-US2H kernel: [ 99.904185] usb 5-3: device descriptor read/64, error -110 Oct 12 20:14:29 REMOVED-GA-MA785GM-US2H kernel: [ 115.144188] usb 5-3: device descriptor read/64, error -110 Oct 12 20:14:29 REMOVED-GA-MA785GM-US2H kernel: [ 115.384178] usb 5-3: new full-speed USB device number 3 using ohci_hcd Oct 12 20:14:44 REMOVED-GA-MA785GM-US2H kernel: [ 130.520196] usb 5-3: device descriptor read/64, error -110 Oct 12 20:14:59 REMOVED-GA-MA785GM-US2H kernel: [ 145.760179] usb 5-3: device descriptor read/64, error -110 Oct 12 20:14:59 REMOVED-GA-MA785GM-US2H kernel: [ 146.000173] usb 5-3: new full-speed USB device number 4 using ohci_hcd Oct 12 20:15:10 REMOVED-GA-MA785GM-US2H kernel: [ 156.408168] usb 5-3: device not accepting address 4, error -110 Oct 12 20:15:10 REMOVED-GA-MA785GM-US2H kernel: [ 156.544188] usb 5-3: new full-speed USB device number 5 using ohci_hcd Oct 12 20:15:20 REMOVED-GA-MA785GM-US2H kernel: [ 166.952181] usb 5-3: device not accepting address 5, error -110 Oct 12 20:15:20 REMOVED-GA-MA785GM-US2H kernel: [ 166.952215] hub 5-0:1.0: unable to enumerate USB device on port 3 Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H kernel: [ 167.216164] usb 6-2: new low-speed USB device number 2 using ohci_hcd Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H mtp-probe: checking bus 6, device 2: "/sys/devices/pci0000:00/0000:00:13.1/usb6/6-2" Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H mtp-probe: bus: 6, device: 2 was not an MTP device Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H kernel: [ 167.396138] input: Logitech USB Mouse as /devices/pci0000:00/0000:00:13.1/usb6/6-2/6-2:1.0/input/input16 Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H kernel: [ 167.396442] generic-usb 0003:046D:C00C.0003: input,hidraw2: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:13.1-2/input0 Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H kernel: [ 167.660187] usb 6-3: new full-speed USB device number 3 using ohci_hcd Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H mtp-probe: checking bus 6, device 3: "/sys/devices/pci0000:00/0000:00:13.1/usb6/6-3" Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H mtp-probe: bus: 6, device: 3 was not an MTP device Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H kernel: [ 167.859045] logitech-djreceiver 0003:046D:C52B.0006: hiddev0,hidraw3: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:13.1-3/input2 Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H kernel: [ 167.865086] input: Logitech Unifying Device. Wireless PID:400a as /devices/pci0000:00/0000:00:13.1/usb6/6-3/6-3:1.2/0003:046D:C52B.0006/input/input17 Oct 12 20:15:21 REMOVED-GA-MA785GM-US2H kernel: [ 167.865291] logitech-djdevice 0003:046D:C52B.0007: input,hidraw4: USB HID v1.11 Mouse [Logitech Unifying Device. Wireless PID:400a] on usb-0000:00:13.1-3:1 Oct 12 20:15:24 REMOVED-GA-MA785GM-US2H colord: io/hpmud/musb.c 139: unable get_string_descriptor -1: Operation not permitted Oct 12 20:15:24 REMOVED-GA-MA785GM-US2H colord: io/hpmud/musb.c 2040: invalid product id string ret=-1 Oct 12 20:15:24 REMOVED-GA-MA785GM-US2H colord: io/hpmud/musb.c 139: unable get_string_descriptor -1: Operation not permitted Oct 12 20:15:24 REMOVED-GA-MA785GM-US2H colord: io/hpmud/musb.c 2045: invalid serial id string ret=-1 Oct 12 20:15:24 REMOVED-GA-MA785GM-US2H colord: io/hpmud/musb.c 139: unable get_string_descriptor -1: Operation not permitted Oct 12 20:15:24 REMOVED-GA-MA785GM-US2H colord: io/hpmud/musb.c 2050: invalid manufacturer string ret=-1

    Read the article

  • After tarball restore my PC (tar xvfpz backup.tgz -C /), my sound card and network are not working. How to detect?

    - by axton hunger
    1 . I have a old laptop I installed Ubuntu 12.04 on. (It was ACER) 2 . I booted into single user mode and backed it up via cd / sudo -i tar cvpzf backup.tgz --exclude=/proc --exclude=/dev --exclude=/lost+found --exclude=/backup.tgz --exclude=/mnt --exclude=/sys / 3 . I installed a fresh copy of Ubuntu 1204 on my new laptop (It is Dell) 4 . I boot into single user mode 5 . I backup the existing /boot directory 6 . I untar my backup to restore on to the Dell sudo tar xvfpz backup.tgz -C / 7 . I restore the previous /boot directory again 8 . I boot it up, and my profile and settings are loaded ok but, Ubuntu shows that there is no Sound Card.. I cannot use unity to drag and change volume. I noticed that the network card also doesnt work. ** How do you make ubuntu recognize changed hardware, if the hardware is already configured for a different laptop? Does anyone know?**

    Read the article

  • Using RabbitMQ (Java client), is there a way to determine if network connection is closed during con

    - by MItch Branting
    I'm using RabbitMQ on RHEL 5.3 using the Java client. I have 2 nodes (machines). Node1 is consuming messages from a queue on Node2 using the Java helper class QueueingConsumer. QueueingConsumer consumer = new QueueingConsumer(channel); channel.basicConsume("MyQueueOnNode2", noAck, consumer); while (true) { QueueingConsumer.Delivery delivery = consumer.nextDelivery(); ... Process message - delivery.getBody() } If the interface is brought down on Node1 or Node2 (e.g. ifconfig eth1 down), the client (above) never knows the network isn't there anymore. Does RabbitMQ provide some type of configuration on the Java client that can be used to determine if the connection has gone away. Shutting down the RabbitMQ server on Node2 will trigger a ShutdownSignalException, which can be caught and the app can go into a reconnect loop. But bringing down the interface doesn't cause any type of exception to happen, so the code will be waiting forever on consumer.nextDelivery(). I've also tried using the timeout version of this call. e.g. QueueingConsumer consumer = new QueueingConsumer(channel); channel.basicConsume("MyQueueOnNode2", noAck, consumer); int timeout_ms = 30000; while (true) { QueueingConsumer.Delivery delivery = consumer.nextDelivery(timeout_ms); if (delivery == null) { if (channel.isOpen() == false) // Seems to always return true { throw new ShutdownSignalException(); } } else { ... Process message - delivery.getBody() } } but appears that this always returns true (even though the interface is down). I assume registering for the ShutdownListener on the connection will yield the same results, but haven't tried that yet. Is there a way to configure some sort of heartbeat, or do you just have to write custom lease logic (e.g. "I'm here now") in order to get this to work?

    Read the article

  • How to Impersonate a user for a file copy over the network when dns or netbios is not available

    - by Scott Chamberlain
    I have ComputerA on DomainA running as userA needing to copy a very large file to ComputerB on WorkgroupB which has the ip of 192.168.10.2 to a windows share that only userB has write access to. There is no netbios or dns resolving so the computer must be refrenced by IP I first I tried AppDomain.CurrentDomain.SetPrincipalPolicy(System.Security.Principal.PrincipalPolicy.WindowsPrincipal); WindowsIdentity UserB = new WindowsIdentity("192.168.10.2\\UserB", "PasswordB"); //Execption WindowsImpersonationContext contex = UserB.Impersonate() File.Copy(@"d:\bigfile", @"\\192.168.10.2\bifgile"); contex.Undo(); but I get a System.Security.SecurityException "The name provided is not a properly formed account name." So I tried AppDomain.CurrentDomain.SetPrincipalPolicy(System.Security.Principal.PrincipalPolicy.WindowsPrincipal); WindowsIdentity webinfinty = new WindowsIdentity("ComputerB\\UserB", "PasswordB"); //Execption But I get "Logon failure: unknown user name or bad password." error instead. so then I tried IntPtr token; bool succeded = LogonUser("UserB", "192.168.10.2", "PasswordB", LogonTypes.Network, LogonProviders.Default, out token); if (!succeded) { throw new Win32Exception(Marshal.GetLastWin32Error()); } WindowsImpersonationContext contex = WindowsIdentity.Impersonate(token); (...) [DllImport("advapi32.dll", SetLastError = true)] static extern bool LogonUser( string principal, string authority, string password, LogonTypes logonType, LogonProviders logonProvider, out IntPtr token); but LogonUser returns false with the win32 error "Logon failure: unknown user name or bad password" I know my username and password are fine, I have logged on to computerB as that user. Any reccomandations

    Read the article

  • How do I set up a public server on a network?

    - by tyjkenn
    I am trying to set up a personal cloud server with OwnCloud on Ubuntu. LAMP is all set up. I was able to access it using the external IP address when I connected it directly to the modem, but what if I what if I want my server to share a LAN? I still want it accessible over the internet, but then if I go to the IP address from a web browser, it just tries to log into to router admin tools. The internal IP address works across the LAN, but I want to be able to access it from anywhere. This may be simple and I may be over-thinking it, but how do access my server? The router I am using is ASUS WL-520GU.

    Read the article

  • Why are UDP messages from outside the network received but not delivered?

    - by Warren Pena
    I have an Ubuntu Server 10.04 application I've developed that receives messages over a UDP port. The ultimate purpose of this application is to receive messages sent from workers' 3G modems out in the field. If use netcat on either another ubuntu Server or my Vista laptop (both on the same LAN as my test machine) to send a message, the message arrives correctly and appears in my application. However, if I go out to my car and use its 3G modem to send a message from the same Vista laptop, it doesn't work. If I run tcpdump -A, I see the message arrive correctly, but it's never delivered to my application. Clearly, the OS is the one making the choice not to deliver the messages (else they wouldn't appear in tcpdump nor would my app receive them when coming from local machines). I have not installed any firewall software on this machine, nor am I aware of anything installed by default that would block the traffic. sudo iptables --list returns Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination I'm not too familiar with iptables, but it looks to me like that's telling it to not do anything. What could be going on that's preventing my messages from being delivered?

    Read the article

  • How to make sysctl network bridge settings persist after a reboot?

    - by user183394
    I am setting up a notebook for software demo purpose. The machine has 8GB RAM, a Core i7 Intel CPU, a 128GB SSD, and runs Ubuntu 12.04 LTS 64bit. The notebook is used as a KVM host and runs a few KVM guests. All such guests use the virbr0 default bridge. To enable them to communicate with each other using multicast, I added the following to the host's /etc/sysctl.conf, as shown below net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-call-arptables = 0 Afterwards, following man sysctl(8), I issued the following: sudo /sbin/sysctl -p /etc/sysctl.conf My understanding is that this should make these settings persist over reboots. I tested it, and was surprised to find out the following: root@sdn1 :/proc/sys/net/bridge# more *tables :::::::::::::: bridge-nf-call-arptables :::::::::::::: 1 :::::::::::::: bridge-nf-call-ip6tables :::::::::::::: 1 :::::::::::::: bridge-nf-call-iptables :::::::::::::: 1 All defaults are coming back! Yes. I can use some kludgy "get arounds" such as putting a /sbin/sysctl -p /etc/sysctl.conf into the host's /etc/rc.local but I would rather "do it right". Did I misunderstand the man page or is there something that I missed? Thanks for any hints. -- Zack

    Read the article

  • Sonicwall routing between multiple subnets on multiple interfaces

    - by Rain
    As shown by the network diagram below, I have two completely separate networks. One is being managed by a Sonicwall NSA 220, the other by some other router (the brand is not important). My goal is to allow devices within the 192.168.2.0/24 network to access devices in the 192.168.3.0/24 network. Allowing the reverse (192.168.3.0/24 - 192.168.2.0/24) is not required. So far, I have done the following: I connected the X3 Interface on the Sonicwall to the 192.168.3.0/24 network switch (shown as the dashed red line in the diagram). Next, I gave it a static ip address of 192.168.3.254 and set the Zone to LAN (the same Zone for the X0 interface). Judging by various articles and KBs I've read, this is all that should be necessary, although it does not work. I can ping 192.168.3.254 from any device in the 192.168.2.0/24 network although I cannot ping/connect to any device within the 192.168.3.0/24 network. Any help would be greatly appreciated! Network Diagram: (I asked a similar, yet more complicated, question earlier; although, I realized that I cannot solve that without first solving this (which may actually solve my original question))

    Read the article

  • Xen HVM networking wont work

    - by Nathan
    I'm trying to get a Xen HVM network working using route however I am failing. Xen PV works fine using Ubuntu but when installing Ubuntu on HVM it fails to pick up the network. I'll let you know now that I'm not that experienced with Xen so I would appreciate any help. vm104 is the HVM thats causing me the problems, here is the configs that I believe should help resolve the problem. [root@eros vm104]# cat vm104.cfg import os, re arch = os.uname()[4] if re.search('64', arch): arch_libdir = 'lib64' else: arch_libdir = 'lib' kernel = '/usr/lib/xen/boot/hvmloader' builder = 'hvm' memory = 6000 shadow_memory = '8' cpu_weight = 256 name = 'vm104' vif = ['type=ioemu, ip=85.25.x.y, vifname=vifvm104.0, mac=00:16:3e:52:3d:fe, bridge=xenbr0'] acpi = 1 apic = 1 vnc = 1 vcpus = 4 vncdisplay = 3 vncviewer = 0 vncconsole = 1 vnclisten = '217.118.x.y' vncpasswd = 'kCfb5S4tE7' serial = 'pty' disk = ['phy:/dev/vpsvg/vm104_img,hda,w', 'file:/home/solusvm/xen/iso/Windows-Server-2008-RC2.iso,hdc:cdrom,r'] device_model = '/usr/' + arch_libdir + '/xen/bin/qemu-dm' boot = 'cd' sdl = '0' usbdevice = 'tablet' pae=1 [root@eros /]# cat /etc/xen/xend-config.sxp | egrep -v "(^#.*|^$)" (xend-unix-server yes) (xend-unix-path /var/lib/xend/xend-socket) (xend-relocation-hosts-allow '^localhost$ ^localhost\\.localdomain$') (network-script network-route) (vif-script vif-route) (network-script 'network-route netdev=eth0') (dom0-min-mem 256) (dom0-cpus 0) (vnc-listen '0.0.0.0') (vncpasswd '') (keymap 'en-us') The Windows install will not pick up the network - I've tried setting the IP manually by using the Xen servers IP as the gateway and setting the main IP in Windows but no luck. If anyone needs any more information let me know and I appreciate any input!

    Read the article

  • 10/100 Network performing at 1.5 to 2.0 megabyte per second - is that below normal?

    - by burnt1ce
    This comes out to about 12 to 16 megabit/seond. I've read in forums that people are getting much higher speeds (ie: "40-60 Mb/s" http://forums.cnet.com/5208-7589_102-0.html?threadID=265967). I'm getting my benchmark by having a unmanged 5 port switch connected to a WRT54GS router connect. I'm sending a file from a computer connect to the WRT54GS to another computer that's connect to the unmanaged 5 port switch. Is the linkage of the switch causing this massive overhead? i doubt it. What could explain the slow down? electrical interference?

    Read the article

  • Inter-vlan routing issues

    - by DKNUCKLES
    I've been brought in to help administer a network and I've run into an issue - I'm not sure why this one is beyond me, however I figure an extra set of eyes on the problem may help resolve the issue. I have an HP MSM720 controller and at the time I'm trying to set up a basic hotspot set up with access points. For the time being I'm just looking to have people authenticate with a PSK and access the internet and other resources (namely printers) on other vlans. The user authenticates and the DHCP server on the controller gives them a 192.168.1.0/24 address. They are able to successfully browse the internet and ping machines on other networks, however they are unable to print to network printers that sit on the same LANs as the very computers that wireless clients can ping. The (extremely simplified) topology is as follows Computers on the wireless 192.168.1.1 network are able to ping computers on the 192.168.0.0 network, however cannot ping or print to the printers on the same network. I'm baffled and I have no idea why this is the case. Can anyone shed some light on this for me? Can someone spot the error of my configuration? EDIT : It should be noted that for whatever reason other computers on the 10.0.100.0/24 network cannot even ping the gateway of the Wireless Access network (192.168.1.1) - I'm not sure if this is relevant. These are the VLANS listed on the controller.

    Read the article

  • How can I route all network traffic through Sonicwall Netextender VPN Client with Ethernet internet sharing enabled on a mac?

    - by Ryan Smith
    I basically have a sonic wall firewall protecting a server which I want to SSL VPN log into with multiple computers. However, I would like to do this by having those computers (or router with computer) connected to a Mac's ethernet port (the vpn would be over wireless) through the internet sharing feature on the iMac. We use the provided Sonicwall Netextender VPN Client to connect to the firewall / server and would like to only have to use one SSL ID to cover all the computers by only having the central Mac sign in. Can anyone out there help me achieve this or tell me it isn't possible? Thank a lot.

    Read the article

  • Lion server profile manager, device enrollment doesn't work

    - by user964406
    I am in the process of setting up Lion Servers profile manager to manage iPads on our local school network. I don't need to manage them while they are outside the network. I have successfully had it working on my personal network. The school network is behind a proxy which we have no control over. I can get the iPads to view the mydevices page and install a trust cert. I have managed to get an iPad to successfully install the remote management profile. After this the profile manager bugs out. It will list the active task of 'new device (sending)' but it's unable to complete the task. If I click on the device on profile manager and try any of the actions out they will all fail to complete. I am using the auto generated certificates and this works if I bring the server and iPad outside of the school network. Shortly after device enrollment the system log on the Lion server reports the following Replaced the actual ip address with INTERNALIP Jun 4 08:40:53 mini sandboxd[760] ([778]): applepushservice(778) deny network-outbound INTERNALIP:8080 Jun 4 08:40:53 mini sandboxd[760] ([778]): applepushservice(778) deny network-outbound INTERNALIP:8080 Jun 4 08:40:53 mini applepushserviced[778]: Got connection error Error Domain=NSPOSIXErrorDomain Code=1 "The operation couldn\u2019t be completed. Operation not permitted" UserInfo=0x7fa483b1a340 {NSErrorFailingURLStringKey=https://albert.apple.com/WebObjects/ALUnbrick.woa/wa/deviceActivation?device=Mac OS, NSErrorFailingURLKey=https://albert.apple.com/WebObjects/ALUnbrick.woa/wa/deviceActivation?device=Mac OS} Jun 4 08:40:53 mini applepushserviced[778]: Failed to get client cert on attempt 2, will retry in 15 seconds Does anyone have any ideas on how to get past this stage? Thanks in advance.

    Read the article

< Previous Page | 217 218 219 220 221 222 223 224 225 226 227 228  | Next Page >