Search Results

Search found 6791 results on 272 pages for 'touch typing'.

Page 221/272 | < Previous Page | 217 218 219 220 221 222 223 224 225 226 227 228  | Next Page >

• Switch Windows 8 from a hybrid MBR/GPT => GPT only on Macbook Pro Retina

  - by Sid

  I used DiskUtility+Bootcamp Wizard to setup my hard drive for Windows 8 (final MSDN). Somewhere in that process, the Apple tools turned my GPT disk into a hybrid MBR/GPT. All my 4 primary MBR partitions are used up, so when I try turning on Bitlocker in Windows 8, it complains about not finding a System drive. I know on Windows 8 the Bitlocker setup tries to create the 200(?)MB system partition if it's missing. However with all 4 partitions filled I suspect it can't create system drive = it can't find it = throws back an error like "BitLocker Setup could not find a target system drive. You may need to manually prepare your drive for BitLocker". I've already tried disabling hibernation, swap file etc. Now I'm thinking that if I were to get rid of the MBR scheme altogether, perhaps I can be alright within the GPT world without MBR's 4 primary partitions limit. So, how can I get rid of the MBR tables on the hybrid scheme in a manner that still leaves Mac OS and Windows 8 in working conditions? Details: Hardware is the MacbookPro Retina. Primary MBR partitions are consumed as follows: EFI partition HFS+ partition (=encrypted, therefore ="Apple_CoreStorage") HFS+ partition (Recovery partition, contains unencrypted Mac bootloader) NTFS partition (Windows8 all-in-one partition) diskutil list output sid-mbpr:~ sid$ diskutil list /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *251.0 GB disk0 1: EFI 209.7 MB disk0s1 2: Apple_CoreStorage 160.0 GB disk0s2 3: Apple_Boot Recovery HD 650.0 MB disk0s3 4: Microsoft Basic Data Win8 90.1 GB disk0s4 GPT vs MBR addresses sid-mbpr:~ sid$ sudo gptsync /dev/rdisk0 Password: Current GPT partition table: # Start LBA End LBA Type 1 40 409639 EFI System (FAT) 2 409640 312909639 Unknown 3 312909640 314179175 Mac OS X Boot 4 314179584 490233855 Basic Data Current MBR partition table: # A Start LBA End LBA Type 1 1 409639 ee EFI Protective 2 409640 312909639 ac Apple RAID 3 312909640 314179175 ab Mac OS X Boot 4 * 314179584 490233855 07 NTFS/HPFS Status: GPT partition of type 'Unknown' found, will not touch this disk.** **: Ignore this message, the gptsync tool is old and doesn't understand the UUID for "Apple_CoreStorage" / FileVault2 partitions. Since LBA addresses are alright, safe to ignore this message.

  Read the article

• httpd.config Easy Apache WHM CentOS

  - by jessie

  First let me explain how I got to this situation. I run a Streaming Video Site. Videos are about 100-250MB in size at any given time there are 500 people on the site. So I guess that would make then static. Recently My site started getting really slow and the only way to fix it temporarily was to restart apache. Now there was no change in traffic that could have caused this. My site is not being attacked. My hosting company recomended to implement mpm_mod and suPHP. They did that by using Easy Apache in WHMS. Then everything was working fine but a little slow. I researched around and to my understanding that mpm will do that but be more table. I was told that installing FastCGI would speed things up just enough. Well that made everything worse. The site is slow and time's out. I used WHM and took off fastCGI but its still the same, it seems like everything i do as of now nothing changes. I even did a roll back on the htconfig file but that didn't work. I'm not sure how to fix this. and my hosting network guy wont be able to touch the problem until Tuesday. I have root access.

  Read the article

• Server Bash Line Wrapping Over Text & In Wrong Place

  - by Pez Cuckow

  This is quite a hard problem to explain, when connecting to one of my servers using the bash shell, under any user the line wrapping is broken and has all sorts of problems. Once of which I detail in screenshots below: Other problems I experience include nano getting very confused about which line and or letter I am on, as shown by typing the same message into nano: These problems only occur when connecting as I previously mentioned to one of my servers which runs CentOs. Do you know why this is occurring and what I can do to fix it? On other servers the message works fine! Thanks for your time, Output of requested commands: Server that doesn't work properly: Working server: Could it perhaps be the custom prompt on the non working server? In .bashrc PS1='\e[1;32m\u@\h\e[m:\e[1;34m\w\e[m$ ' Commenting this out appeared to resolve the problem. Google says line wrapping errors can occur if you don't conform to these rules use the \[ escape to begin a sequence of non-printing characters, and the \] escape to signal the end of such a sequence I am not sure where this would fit in on my prompt?

  Read the article

• Adding port forwardings programmatically on a ControlMaster SSH session

  - by aef

  I just found out about the ControlMaster/ControlPath feature of OpenSSH, which allows you to use a single SSH connection to run multiple terminals. As I often use SSH to use port forwarding to get encrypted and authenticated VNC sessions I instantly recognized that you can't add port forwardings to a remote server to which you already have an established connection. This sucks. Sometimes later I found out that you can circumvent this limitation by typing ~C in a running SSH terminal session. This opens up a command-line which allows you to add or remove port forwardings. My quesion now is: How can I add port forwardings on an existing SSH session which is using the ControlMaster/ControlPath feature, without the need to have access to a terminal session inside that SSH session. I need this to enable my script which starts a secure tunneled VNC connection for me to add and later remove its port forwardings. (I know I could use a terminal multiplexer such as GNU Screen or tmux, actually I'm doing this already. But I like the idea of using just one SSH session for serveral reasons.)

  Read the article

• Why are FMS logs filled with 'play' event status code 408 for a failed webcast?

  - by Stu Thompson

  Recently we had a live webcast event go horribly wrong. I'm doing the technical post-mortem, with limited information. We know that the hardware encoder (a Digital Rapid Touch Stream Web HDI) was unable to send upstream at a sustained reliable high rate. What we don't know is if the encoder's connection was problematic (Zürich), or that of the streaming server (in Frankfurt). Unfortunately, I've got three different vendors all blaming each other (the CDN who runs the server, the on-site ISP and the on-site encoding team.) In the FMS log files I see a couple of interesting things: Zillions of Status Code 408 on play event entries for clients. Adobe's documentation stats that this "Stream stopped because client disconnected". ("Zillions" would be a ratio of 10 events for every individual IP address.) Several unpublish / (re)publish events per hour for the encoder I'd like to know if all those 408s could tell me with authority that the FMS server was starved for bandwidth, or that the encoding signal was starved (and hence the server was disconnecting clients.) Any clues?

  Read the article

• iOrgSoft Video Converter for Mac

  - by terryhao

  [url=http://www.iorgsoft.com/Video-Converter-for-Mac/]video converter for mac[/url] IOrgSoft[url=http://www.iorgsoft.com/Video-Converter-for-Mac/]video converter for mac[/url] is an excellent video converting and editing software for Macintosh users. A built-in powerful video player, trimming, splitter/joiner/merger tools give you everything you need to manage your videos on mac. This mac converter supports many video formats like AVI, MP4, WMV, MPEG-1,2, YouTube(FLV), Limewire, Realplayer(RM,RMVB), Quicktime(MOV), MKV, MOD, TOD, ASF, 3GP, 3G2, AVCHD/M2TS/MTS/TS/TRP/TS, MXF, etc. Video Converter for Mac features a very clean user interface which makes this task a breeze. You can trim/clip any segments and optionally merge/join and sort them to create your personal movie, crop frame size to remove any unwanted area in the frame just like a pair of smart scissors and set the output video parameters such as video resolution, video frame rate, audio codec, video codec and video quality. Converted videos can be imported into imovie/itunes/FCE/FCP/QuickTime Pro or played on iPad, iPod touch, iPod classic, iPod nano, iPhone, iPhone 3GS, Apple TV, PSP, PS3, Creative Zen, iRiver PMP, Archos, mobile phones and other MP4/MP3 players. Video Converter for Mac makes video conversion easy. Free download now and have a try for yourself! [url=http://www.iorgsoft.com/Video-Editor-for-Mac/]Video Editor for Mac[/url] [url=http://www.iorgsoft.com/Mod-Converter/]mod converter[/url] [url=http://www.iorgsoft.com/Mod-Converter-for-Mac/]mod converter for mac[/url]

  Read the article

• Can't do more than one activity at a time after switching modems

  - by vallorn

  I had to replace the Motorola 2210 DSL modem that I got when I signed up for AT&T DSL Direct a few years ago. The modem kept randomly restarting and it eventually gave out on me. I am assuming overheating was the cause here because it was almost too hot to touch. In any case, I replaced it with a Netgear DM111PSP. It works fine but I can't do more than one activity at a time with it. If my wife is watching Netflix, there is a noticeable delay/latency when trying to view web sites. It's even worse if I try to play an on-line game while she's streaming; the game is basically unplayable. The odd thing is, the only other activity I can do while she's streaming is stream another Netflix show myself. There is no delay when doing that, no buffering either. I'm not a networking guy so maybe there is an explanation for it but I find that kind of odd. I've tried using QoS through my Buffalo N600 wireless router and it doesn't seem to help. With the old Motorola modem, she could be watching Netflix while I play a game and everything worked just fine. Is there anything I can check or reconfigure possibly on the modem that would account for this? Should I just ditch the Netgear and get another modem instead? I have the Netgear modem connected to the Buffalo router in a bridged mode. Its the same exact setup as I had with the Motorola and as far as I can tell, it's not the router that is the cause.

  Read the article

• Make Google Chrome's address bar prefer page titles to domain names when offering completions?

  - by Ryan Thompson

  I've recently switched from Firefox to Chrome, and the thing I miss most from Firefox is the "Awesome Bar" that suggests completions for what I type primarily based on page titles, and then secondarily based on domain names. Chrome offers both matching URLs and titles, just like like Firefox, but Chrome seems to always prefer a matching domain name over a matching page title or a match to another part of the URL (besides the domain), no matter how many times I pass over the former for the latter. In fact, Chrome also prefers to suggest a search rather than matching anything other than a domain name. So is there any hidden preference I can change to tell Chrome that I care more about page titles than domain names? Example: I want to go to Google Reader, so I press Control+L and begin typing "reader". The URL for google reader is http://www.google.com/reader/view/#overview-page, so the domain name is www.google.com, which does not contain the word "reader". So the first option that Chrome suggests is either another site that has "reader" as part of the domain, or a search for "reader" with the default search engine. No matter how many times I scroll down and select Google Reader, Chrome never "learns" that that's what I want.

  Read the article

• Ubuntu xrandr rotate issue

  - by user83544

  I've just bought a second monitor for my PC which happens to be a pivot monitor. I've already read lots of forums related to my problem but haven't come across a solution - I have the same symptoms as dozens of posts but no matter whatever I try it just doesn't work. I've already changed the xorg.conf file and added in the device section just under Driver "nvidia" the following for my second monitor: Option "RandRRotation" "on" When I save and reboot I try to rotate my screen with the nvidia X server settings by choosing the second monitor and clicking either "left" or "right" for the rotation. It immediately exits the nvidia settings window and does nothing. I tried within the terminal by typing: xrandr -o right I get the following error: X Error of failed request: BadMatch (invalid parameter attributes) Major opcode of failed request: 154 (RANDR) Minor opcode of failed request: 2 (RRSetScreenConfig) Serial number of failed request: 14 Current serial number in output stream: 14 I actually manage to rotate it with Option "Rotate" "CCW" instead of "RandRRotation". The problem with this solution is that you get the second monitor in the right position, but any window you open on that screen is practically unchangeable. You can't change the size nor move it, making it useless for reading PDFs, which is the main reason why I bought this second screen to help me write my thesis. Any help is really appreciated. sudo lshw -c video hiram@hiram-linux:~$ sudo lshw -c video *-display description: VGA compatible controller product: nVidia Corporation vendor: nVidia Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nvidia latency=0 resources: irq:16 memory:f8000000-f9ffffff memory:d8000000-dfffffff memory:d4000000-d7ffffff ioport:dc00(size=12 memory:fbd80000-fbdfffff

  Read the article

• Citrix Metaframe/RD - screen refresh weirdness

  - by southof40

  I access a clients W2003 machine (XEN Virtualization) using RD over Citrix Metaframe. Everything used to be fine. Some weeks ago things turned bad ! All is well initially but after, say, 5 minutes the screen will stop refreshing. Rather weirdly you can then still proceed in a way as you can make the screen refresh by getting the RD window to go through a restore/maximise cycle (this is only possible using the ALT-BREAK shortcut as everything else is locked up). This then allows you to proceed by typing something and going ALT-BREAK to see the results. Using menus is just not possible at all. There's some indications that clearing the java cache between sessions helps. Also that the lockup happens more quickly if you make the 'lots of stuff happen' on the screen - for instance if you do a directory listing of a big directory then often that will cause the lockup to occur. Similary opening a dense Excel workbook and then scrolling it will cause the lockup to occur. Any Metaframe veterans out there who recognise these symptoms ? I'd be very grateful as it's driving me nuts.

  Read the article

• Spotlight actually searching every file on "This Mac"

  - by Cawas

  I know of 2 ways to search for any file in your machine using Finder (some say it's Spotlight) and no Terminal. To prevent answers / comments about Terminal, I consider it either for scripting something or as last resource. It's not practical for lots of usages. For instance, if you want to find something to attach to a mail, or embed in iTunes or any other app, you can just drag n' drop one or many of them. Definitely not practical to do under Terminal. There are many cases of use for any, but the focus here is Graphical User Interface. Well, the 2 ways basically are: Press Cmd + Opt + Spacebar and type in your search. Press the + button, select "System files" and "are included". This is so far my preferred way, but I'm not sure it will go through every file. Open Finder, press Cmd + Shift + G and/or select just one folder. Type in your search and select the folder rather than "This Mac". This will bring files not shown in "This Mac" if you select a folder outside of the default scope. Thing is, none of those is really convenient or have the nice presentation from regular Spotlight, which you get from Cmd + Spacebar and just typing. And, as far as I've heard, the default behavior on Spotlight in Tiger was actually being able to find files anywhere. So, is there any way to make the process significantly simpler? Maybe some tweak, configuration or really good Spotlight alternative? I'd rather keep it simple and tweak Spotlight.

  Read the article

• Linksys router cannot change default password

  - by Jessica M.

  My wireless internet suddenly stopped working today. I have Windows 7 and Lindsys WRT54G router. I tried to log into the Linksys setup router page by typing in www.192.168.1.1 into firefox and it prompted me for a username and password as usual. The problem is when i tried to enter my regular username and password it did not work. I finally solved my problem when I came across this post here and the very last post solved my problem. It suggested I try username: root / password: admin. For some reason the username and password has been changed. When i tried username: root / password: admin , it worked and allowed me to get into the Linksys setup page. The problem is I can't change the username or password anymore. Every time I want to log into my Linksys setup page I have to enter username: root / password: admin. I can't change the "WPA shared key" (password). For the security settings I selected WPA2Personal + AES. Also the post said "If the firmware was upgraded to non-linksys firmware - the default will be different" . The problem is I didn't update anything and I'm worried that someone installed a virus or something or somehow changed the firmware on my router. How did I get non-Linksys firmware on my router? EDIT: I figured out how to change the password when I log into the Lynksys setup page. Administration -- Management -- password. I still don't understand if my router firmware was changed or who changed it or if it happened by mistake.

  Read the article

• Can a hardware firewall block a server accessing its OWN UNC shares?

  - by Simon

  I need to set up a UNC share for my hosted dedicated server to access a share on itself. Unfortunately TFS requires a UNC share. I am on a Windows Server 2008 Standard SP2 64bit dedicated server behind a PIX 501 firewall hosted with GoDaddy. I just cannot get the server to access itself and get this error: Windows cannot access \\SERVER\SHARE Check the spelling of the name.. etc. I've found numerous questions about this but no answer to my problem. Server 2008 Standard x64 SP2 Workgroup - not domain Windows Firewall is off Computer browser service is on I am trying to access \\MYMACHINE\TFS-BUILDS by typing in - or double clicking. Neither works. Machine has single network card Filesharing wizard says share was ok Share was showing under 'Computer management' Permissions are set to 'everyone' full control No obvious errors in eventlog Reboot didn't fix it Unfortunately I cannot try to access other shares in or out of this machine because it is a hosted dedicated server and the only machine behind a hardware firewall. The only thing left i can think of is that the hardware firewall needs to be configured. Is this possible? Does 'UNC traffic' go out of the machine and then back in again?

  Read the article

• Windows 7 keeps insisting that it needs to check disk for consistency, but never does

  - by Mike

  Lately Windows 7 has been telling me that I need to check disk D: for consistency. This happens more than 50% of the time when booting up. The first time, I didn't touch anything so that it would go ahead and do its scan. It didn't seem to do anything - just booted straight into Windows. The second time I tried to skip it by pressing any key. It ignored all of my keystrokes and still counted down to 0 (then skipped the disk check). Sometimes, it gets down to 0 but then just hangs... no indication that anything is going on. This is happening on a < 3 month old laptop. C: and D: are on the same physical disk - just two partitions. I never get any notification that C: needs to be checked for consistency. It's a ~300GB HD. C: has 60gb (32gb free) and D: has ~240GB (122gb free). What could be causing this to keep coming up? What can I do to fix it? Thanks!

  Read the article

• location of index.html CentOS 6

  - by user2118559

  Based on this http://www.servermom.com/how-to-add-new-site-into-your-apache-based-centos-server/454/ tutorial installed Apache-based CentOS Server I use putty.exe as editor vi /etc/httpd/conf/httpd.conf at very bottom modified to <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot /var/www/fikitipis.com/public_html ServerName www.fikitipis.com ServerAlias fikitipis.com ErrorLog /var/www/fikitipis.com/error.log CustomLog /var/www/fikitipis.com/requests.log common </VirtualHost> So expect that index is at /var/www/fikitipis.com/public_html When in browser type ip address of server, see Apache 2 Test Page powered by CentOS and so on You may now add content to the directory /var/www/html/ Then [root@vps ~]# ls /var/www/ see cgi-bin domain.com error fikitipis.com html icons Checking content of directories ls /var/www/domain.com/public_html, ls /var/www/fikitipis.com/public_html, /var/www/html/ are empty Where is index.html? Did touch /var/www/fikitipis.com/public_html/index1.html then vi /var/www/fikitipis.com/public_html/index1.html, typed a, then wrote some text in file, then Escape and shift+zz. And in browser http://111.111.11.111/index1.html and see what I had wrote. So until now seems that all works

  Read the article

• i7 overclocking problem

  - by benwebdev

  Hi everyone, I've got an overclocked system that seems to be misbehaving. When trying to boot up from cold the system just hangs and nothing is output to the screen. Fans are on as they should but nothing happens to finish the boot. From here I have to switch it off then on again and the boot completes. If I go into the tweak menu in the BIOS I'm informed that a boot has failed I've been in touch with Overclockers UK support a bit and theres not yet been a solution. We've mainly been tweaking the voltage for the CPU. Any suggestions? I'm new to Overclocking which is why I got a bundle with OCUK. With this issue happening on Cold Boot too its tricky to test as I have to make a change then wait till the next day. My system is here: Intel Core i7 930 2.80Ghz overclocked to 4GHz Gigabyte X58A-UD3R (BIOS Version: FC) 6GB RAM Power Supply - CoolerMaster Silent Pro M series 700W One suggestion made by OCUK was that maybe its the power supply but I'm not sure and dont have a spare - it's brand new and a pretty expensive piece of kit. Any thoughts on this? Other recomendations for Power? thanks Ben

  Read the article

• SQL Server 2005 standard filegroups / files for performance on SAN

  - by Blootac

  Ok so I've just been on a SQL Server course and we discussed the usage scenarios of multiple filegroups and files when in use over local RAID and local disks but we didn't touch SAN scenarios so my question is as follows; I currently have a 250 gig database running on SQL Server 2005 where some tables have a huge number of writes and others are fairly static. The database and all objects reside in a single file group with a single data file. The log file is also on the same volume. My interpretation is that separate data files should be used across different disks to lessen disk contention and that file groups should be used for partitioning of data. However, with a SAN you obviously don't really have the same issue of disk contention that you do with a small RAID setup (or at least we don't at the moment), and standard edition doesn't support partitioning. So in order to improve parallelism what should I do? My understanding of various Microsoft publications is that if I increase the number of data files, separate threads can act across each file separately. Which leads me to the question how many files should I have. One per core? Should I be putting tables and indexes with high levels of activity in separate file groups, each with the same number of data files as we have cores? Thank you

  Read the article

• How to start using twill?

  - by brilliant

  How do I start using twill? I have just downloaded it, unpacked it and clicked on the setup .py file in the folder. The black window (terminal) appeared for a moment and vanished. (I do have Python 2.5 installed on my computer - along with SDK from Google App Engine) In the twill documentation section it says: Downloading twill The latest release of twill is twill 0.9, released Thursday, December 27th, 2007; it is available for download at http://darcs.idyll.org/~t/projects/twill-0.9.tar.gz. You can also use Python's easy_install to install or upgrade twill. twill works with Python 2.3 or later. To start using twill, install it and then type twill-sh. At the prompt type: go http://www.slashdot.org/ show showforms showhistory I am not clear from this passage what I am supposed to type (only "twill-sh" or "twill-sh" and all the words under that line) and where (I tried typing it in the command prompt window of my computer - to no avail) Can, anyone, please, help me out here? Thank You in advance.

  Read the article

• Google: "302 Moved" in Firefox

  - by Virtlink

  For some Google search queries executed from the Firefox search bar, or manually by typing in the URL, I get a ''302 Moved'' page. I did a quick virus scan, have checked the hosts file and the plugins and add-ons that are installed in Firefox. Nothing is out of the ordinary. What could be the problem? These URLs (and any URL with google.com, empty and firefox-a in them) show me a 302 Moved page: https://www.google.com/search?q=c%23+empty+array&client=firefox-a https://www.google.com/search?q=empty&client=firefox-a Whereas these URLs work fine: https://www.google.com/search?q=c%23+empty+array (no firefox-a) https://www.google.com/search?q=empty (no firefox-a) https://www.google.com/search?q=c%23+array&client=firefox-a (no empty) https://www.google.nl/search?q=c%23+empty+array&client=firefox-a (no .com) By default Google redirects my queries to their .nl website, and uses HTTPS. I am currently executing a full system virus scan using Security Essentials. My Firefox plugins were up-to-date. No unfamiliar Firefox plugins or add-ons found. Restarting Firefox did not solve the issue. The issue does not occur in Internet Explorer. The hosts file did not contain any unfamiliar entries.

  Read the article

• Where in the stack is Software Restriction Policies implemented?

  - by Knox

  I am a big fan of Software Restriction Policies for Microsoft Windows and was recently updating our settings for this. I became curious as to where Microsoft implemented this technology in the stack. I can imagine a very naive implementation being in Windows Explorer where when you double click on an exe or other blocked file type, that Explorer would check against the policy. I call this naive because obviously this wouldn't protect against someone typing something in a CMD window. Or worse, Adobe Reader running an external application. On the other hand, I can imagine that software restriction policies could be implemented deep in the stack almost at the metal. In this case, the low level loader would load into memory the questionable file, but mark the memory in the memory manager as non-executable data. I'm pretty sure that Microsoft did not do the most naive implementation, because if I block Java using a path block, Internet Explorer will crash if it attempts to load Java. Which is what I want. But I'm not sure how deep in the stack it's implemented and any insight would be appreciated.

  Read the article

• Adding a Second Wireless Router to an Existing Wired Network

  - by KVCrawford

  I apologize ahead of time, I know this has been asked before, but I'm still having problems...maybe you guys can help. I started out with the basic instructions from the highest-voted answer at http://serverfault.com/questions/41572/adding-a-second-wireless-router-to-my-network The new Wireless router in question is a Linksys Wireless-N Gigabit Router, Model # WRT310N Here are the steps I've taken in setting it up: Plug my laptop into LAN port #2 in the new router. Nothing else is connected at this point Configure the new router to be 192.168.1.200 (the original router is 192.168.1.1, and its DHCP clients are from 192.168.1.100-x.x.x.199) Set the internet connection on the new router to "DHCP Client" Turn off the DHCP server & NAT routing on the new router Plug in a LAN cable from the original router into the LAN port #1 on the new router (NOT the WAN port, nothing is plugged in there) Reset the new router Afterwards, I try to ping 192.168.1.1 from the laptop plugged into LAN port #2 on the new router, with no response. 192.168.1.200 garners no response either. Typing "ipconfig" tells me: Autoconfiguration IP Address: 169.254.198.113 Subnet Mask: 255.255.0.0 Default Gateway: 169.254.198.113 What's going wrong? I appreciate any help!

  Read the article

• Rsync when run in cron doesnt work. Rsync between Mac Os x Server and Linux Centos

  - by Brady

  I have a working rsync setup between Mac OS X Server and Linux Centos when run manually in a terminal. I enter the rsync command, it asks for the password, I enter it and off it goes, runs and completes. Now I know thats working I set out to fully automate it via cron. First off I create an SSH authorized key by running this command on the Mac server: ssh-keygen -t dsa -b 1024 -f /Users/admin/Documents/Backup/rsync-key Entering the password and then confirming it. I then copy the rsync-key.pub file accross to the linux server and place in the rsync user .ssh folder and rename to authorized_keys: /home/philosophy/.ssh/authorized_keys I then make sure that the authorized_keys file is chmod 600 in the folder chmod 700. I then setup a shell script for cron to run: #!/bin/bash RSYNC=/usr/bin/rsync SSH=/usr/bin/ssh KEY=/Users/admin/Documents/Backup/rsync-key RUSER=philosophy RHOST=example.com RPATH=data/ LPATH="/Volumes/G Technology G Speed eS/Backup" $RSYNC -avz --delete --progress -e "$SSH -i $KEY" "$LPATH" $RUSER@$RHOST:$RPATH Then give the shell file execute permissions and then add the following to the crontab using crontab -e: 29 12 * * * /Users/admin/Documents/Backup/backup.sh I check my crontab log file after the above command should run and I get this in the log and nothing else: Feb 21 12:29:00 fileserver /usr/sbin/cron[80598]: (admin) CMD (/Users/admin/Documents/Backup/backup.sh) So I asume everything has run as it should. But when I check the remote server no files have been copied accross. If I run the backup.sh file in a terminal as normal it still prompts for a password but this time its through the Mac Key chain system rather than typing into the console window. With the Mac Key Chain I can set it to save the password so that it doesnt ask for it again but Im sure when run with cron this password isnt picked up. This is where I'm asuming where rsync in cron is failing because it needs a password to connect but I thought the whole idea of making the SSH keys was to prevent the use of a password. Have I missed a step or done something wrong here? Thanks Scott

  Read the article

• Some Can reach bidmail.com others can't.

  - by user69426

  On a windows 7 Professional machine in Chrome one of our Estimating assistants can't get to www.bidmail.com, however the other 3 can. On his machine I did nslookup then bidmail.com and it fails to find it. I then went to a machine that could reach bidmail and did nslookup. It can't find it. I was skeptical and thought maybe it was a cached page so I cleared the cache then went back to bidmail.com was able to get to the page, login, lookup a newly posted bid then download the file. Yet I can not look it up through nslookup and I can't ping it www.bidmail.com and I can't trace it. I remoted to our other warehouse which is set up as a workgroup and attempt to nslookup bidmail and that nslookup fail... and on that machine which has never been to bidmail before it was able to connect to the website! I am totally confused if I can't ping it and I can't use nslookup to get there how in the hell is Chrome getting to the page and how do I get this guy back on? Also while typing this I took a new laptop out of the box plugged it in with no updates and can get to bidmail! omg!

  Read the article

• Firefox 29 - how do I delete history entries visited fewer than x times

  - by lousyuser

  Context: I've been using my Firefox profile for a couple of years now. My history file has become huge, naturally. I got Firefox Sync set up between my main desktop PC and my laptop. HW configs: PC: i5-3450, 8 GB DDR3 RAM, Crucial M4 128 GB SSD laptop: Pentium SU4100, 4 GB DDR3 RAM, WD 5400 rpm HDD Accessing history entries when typing into the Awesome Bar on my desktop takes quite a long time despite the decent config, the laptop is even slower. The experience is quite unresponsive. I figured if I cleared the history up a little bit, I might avoid creating a new profile to speed things up. The question itself: to illustrate: Is there a way to delete all history entries that have been visited fewer than x (let's say 5) times and at the same time the recent visit is fewer than y (let's say 120) days old? afaik the history file is some kind of SQL database, but I'm not really sure how the data is saved, if there's a "safe way" to edit it and what the query to do what I need would look like. Thanks in advance for any help. I kept browsing through previous SuperUser questions to see if I could find relevant information. "In my Firefox profile directory, there is a filed named places.sqlite. Opening it with sqlite reveals (amongst others) the tables moz_places and moz_historyvisits. It seems that moz_historyvisits uses the primary of moz_places to refer to the URLs." As I'm unfamiliar with databases, I don't really understand the way the two tables mentioned in the quote are related. screenshot of a part of the tables I've noticed the visit_count is in a standard format, making it easy to work with. The last_visit_date looks encrypted to my naked eye, but I can't see in which way. Hope that helps, I'm at my wits' end.

  Read the article

• Desktop virtualization

  - by gurpal2000

  Is there currently a proper Type 1 "desktop" hypervisor? Either free or not? This is just for tinkering around at home on some beefy Phenom machines. Basically i want to be able to run say 2 OSs on the same PC but without loading windows or a heavy flavour of linux and then use a hotkey to switch between them. I should get full performance out of them. So do i need something better than vmware workstation and/or virtualbox. I think these are "Type 2"? I already run VMWare w/s and VBox but is there a more performant solution? I saw a YouTube video from Citrix where a laptop was running XP and Vista. With the touch of a hot key they could switch between them. There was no visible underlying OS (there might be a hypervisor)? I have access to Citrix XenDesktop 3 enterprise edition evaluation. I realise this isn't for desktops but can i achieve my goal (geekiness) ? If i use the free XenServer 5.5.0 how do my client PCs access windows/linux/whatever from the xenserver? Is it via a thin client RDP type application? If so if there one for both windows and linux? Also if i do use XenServer can i use USB in either direction? What is Citrix receiver can i use that for (3) ? If so, is there some hotkey i can configure? whatever client is used to access the server software (whether it be on a different server or local) can i get full opengl/directx acceleration? what about Xen? i tried the Xen LiveCD but no clue as how to configure it. As you can see much confusion. Any help/pointers welcome. Cheers.

  Read the article

< Previous Page | 217 218 219 220 221 222 223 224 225 226 227 228  | Next Page >