Search Results

Search found 7086 results on 284 pages for 'proprietary syntax'.

Page 222/284 | < Previous Page | 218 219 220 221 222 223 224 225 226 227 228 229  | Next Page >

• Cant get lm-sensors to load ATI Radeon temp or fan

  - by woody

  New to Linux and having minor issues :/ . I followed this guide initially but did not recieve the proper output and did not show my ATI Radeon HD 5000 temp or fan speed. Then used this guide, same problems exhibited. No issues installing and no errors. I think its not reading i2c for some reason. The proprietary driver is installed and functioning correctly according fglrxinfo. I can use aticonfig commands and view both temp and fan. Any ideas on how to get it working under 'sensors'? When i run 'sudo sensors-detect' this is my ouput # sensors-detect revision 5984 (2011-07-10 21:22:53 +0200) # System: LENOVO IdeaPad Y560 (laptop) # Board: Lenovo KL3 This program will help you determine which kernel modules you need to load to use lm_sensors most effectively. It is generally safe and recommended to accept the default answers to all questions, unless you know what you're doing. Some south bridges, CPUs or memory controllers contain embedded sensors. Do you want to scan for them? This is totally safe. (YES/no): y Silicon Integrated Systems SIS5595... No VIA VT82C686 Integrated Sensors... No VIA VT8231 Integrated Sensors... No AMD K8 thermal sensors... No AMD Family 10h thermal sensors... No AMD Family 11h thermal sensors... No AMD Family 12h and 14h thermal sensors... No AMD Family 15h thermal sensors... No AMD Family 15h power sensors... No Intel digital thermal sensor... Success! (driver `coretemp') Intel AMB FB-DIMM thermal sensor... No VIA C7 thermal sensor... No VIA Nano thermal sensor... No Some Super I/O chips contain embedded sensors. We have to write to standard I/O ports to probe them. This is usually safe. Do you want to scan for Super I/O sensors? (YES/no): y Probing for Super-I/O at 0x2e/0x2f Trying family `National Semiconductor/ITE'... Yes Found unknown chip with ID 0x8502 Probing for Super-I/O at 0x4e/0x4f Trying family `National Semiconductor/ITE'... No Trying family `SMSC'... No Trying family `VIA/Winbond/Nuvoton/Fintek'... No Trying family `ITE'... No Some hardware monitoring chips are accessible through the ISA I/O ports. We have to write to arbitrary I/O ports to probe them. This is usually safe though. Yes, you do have ISA I/O ports even if you do not have any ISA slots! Do you want to scan the ISA I/O ports? (YES/no): y Probing for `National Semiconductor LM78' at 0x290... No Probing for `National Semiconductor LM79' at 0x290... No Probing for `Winbond W83781D' at 0x290... No Probing for `Winbond W83782D' at 0x290... No Lastly, we can probe the I2C/SMBus adapters for connected hardware monitoring devices. This is the most risky part, and while it works reasonably well on most systems, it has been reported to cause trouble on some systems. Do you want to probe the I2C/SMBus adapters now? (YES/no): y Using driver `i2c-i801' for device 0000:00:1f.3: Intel 3400/5 Series (PCH) Now follows a summary of the probes I have just done. Just press ENTER to continue: Driver `coretemp': * Chip `Intel digital thermal sensor' (confidence: 9) To load everything that is needed, add this to /etc/modules: #----cut here---- # Chip drivers coretemp #----cut here---- If you have some drivers built into your kernel, the list above will contain too many modules. Skip the appropriate ones! Do you want to add these lines automatically to /etc/modules? (yes/NO) My output for 'sensors' is: acpitz-virtual-0 Adapter: Virtual device temp1: +58.0°C (crit = +100.0°C) coretemp-isa-0000 Adapter: ISA adapter Core 0: +56.0°C (high = +84.0°C, crit = +100.0°C) Core 1: +57.0°C (high = +84.0°C, crit = +100.0°C) Core 2: +58.0°C (high = +84.0°C, crit = +100.0°C) Core 3: +57.0°C (high = +84.0°C, crit = +100.0°C) and my '/etc/modules' is: # /etc/modules: kernel modules to load at boot time. # # This file contains the names of kernel modules that should be loaded # at boot time, one per line. Lines beginning with "#" are ignored. lp rtc # Generated by sensors-detect on Fri Nov 30 23:24:31 2012 # Chip drivers coretemp

  Read the article

• System Variables, Stored Procedures or Functions for Meta Data

  - by BuckWoody

  Whenever you want to know something about SQL Server’s configuration, whether that’s the Instance itself or a database, you have a few options. If you want to know “dynamic” data, such as how much memory or CPU is consumed or what a particular query is doing, you should be using the Dynamic Management Views (DMVs) that you can read about here: http://msdn.microsoft.com/en-us/library/ms188754.aspx  But if you’re looking for how much memory is installed on the server, the version of the Instance, the drive letters of the backups and so on, you have other choices. The first of these are system variables. You access these with a SELECT statement, and they are useful when you need a discrete value for use, say in another query or to put into a table. You can read more about those here: http://msdn.microsoft.com/en-us/library/ms173823.aspx You also have a few stored procedures you can use. These often bring back a lot more data, pre-formatted for the screen. You access these with the EXECUTE syntax. It is a bit more difficult to take the data they return and get a single value or place the results in another table, but it is possible. You can read more about those here: http://msdn.microsoft.com/en-us/library/ms187961.aspx Yet another option is to use a system function, which you access with a SELECT statement, which also brings back a discrete value that you can use in a test or to place in another table. You can read about those here: http://msdn.microsoft.com/en-us/library/ms187812.aspx  By the way, many of these constructs simply query from tables in the master or msdb databases for the Instance or the system tables in a user database. You can get much of the information there as well, and there are even system views in each database to show you the meta-data dealing with structure – more on that here: http://msdn.microsoft.com/en-us/library/ms186778.aspx  Some of these choices are the only way to get at a certain piece of data. But others overlap – you can use one or the other, they both come back with the same data. So, like many Microsoft products, you have multiple ways to do the same thing. And that’s OK – just research what each is used for and how it’s intended to be used, and you’ll be able to select (pun intended) the right choice. Share this post: email it! | bookmark it! | digg it! | reddit! | kick it! | live it!

  Read the article

• Announcing MySQL Enterprise Backup 3.7.1

  - by Hema Sridharan

  The MySQL Enterprise Backup (MEB) Team is pleased to announce the release of MEB 3.7.1, a maintenance release version that includes bug fixes and enhancements to some of the existing features. The most important feature introduced in this release is Automatic Incremental Backup. The new  argument syntax for the --incremental-base option is introduced which makes it simpler to perform automatic incremental backups. When the options --incremental & --incremental-base=history:last_backup are combined, the mysqlbackup command  uses the metadata in the mysql.backup_history table to determine the LSN to use as the lower limit of the incremental backup. You no longer need to keep track of the actual LSN (as in the option --start-lsn=LSN) or even the location of the previous backup (as in the option --incremental-base=dir:directory_path)This release also incudes various bug fixes related to some options used in MEB. The most important are few of them as listed below,1. The option --force now allows overwriting InnoDB data and log files in  combination with the apply-log and apply-incremental-backup options, and replacing the image file in combination with the backup-to-image and backup-dir-to-image options. 2. Resolved a bug that prevented MEB to interface with third-party storage managers to execute backup and restore jobs in combination with the SBT interface and associated --sbt* options for mysqlbackup. 3. When MEB is run with the copy-back option,  it now displays warnings as existing files are overwritten.For more information about other bug fixes, please refer to the change-log in http://dev.mysql.com/doc/mysql-enterprise-backup/3.7/en/meb-news.html The complete MEB documentation is located at http://dev.mysql.com/doc/mysql-enterprise-backup/3.7/en/index.html. You will find the binaries for the new release in My Oracle Support,  https://support.oracle.comChoose the "Patches & Updates" tab, and then use the "Product or Family (Advanced Search)" feature. If you haven't looked at MEB 3.7.1 recently, please do so now and let us know how MEB works for you. Send your feedback to [email protected].

  Read the article

• SQL SERVER – Difference Between CURRENT_TIMESTAMP and GETDATE() – CURRENT_TIMESTAMP Equivalent in SQL Server

  - by pinaldave

  A common question – I often get from Oracle/MySQL Professionals: “What is the Equivalent to CURRENT_TIMESTAMP in SQL Server?” Here is a common question I often get from SQL Server Professionals: “What are differences between Difference Between CURRENT_TIMESTAMP and GETDATE ()?” Very simple question but have showed up so frequently that I feel like to write about it. Well in SQL Server GETDATE() is Equivalent to CURRENT_TIMESTAMP. However, if you use CURRENT_TIMESTAMP in your select statement it will work fine. You can see in the above example – both of them returns the same value. Now let us go to next question regarding difference between GETDATE and CURRENT_TIMESTAMP. Well, the matter of the fact, there is no difference between them in SQL Server (Reference Link). CURRENT_TIMESTAMP is an ANSI SQL function, whereas GETDATE is T-SQL implementation of the same function. Both of them derive value from the operating system of the computer on which SQL Server instance is running. Above discussion prompts another question – in this case, what should one use GETDATE or CURRENT_TIMESTAMP? Well, this is indeed tricky and interesting question. I think I am very comfortable using the GETDATE () so I will go to use it but a matter of the fact there is no right or wrong answer. If you want to follow ancient saying “When in Rome, do as the Romans do”, I suggest using the GETDATE (), or continue using CURRENT_TIMESTAMP. With that said, there is one very important property we all need to keep in mind. If you use CURRENT_TIMESTAMP while creating an object, they are automatically converted to GETDATE() and stored internally. To illustrate what I am suggesting here is the example - Create a table using the following script CREATE TABLE [dbo].[TestTable]( [Cold2] [datetime] NULL ) ON [PRIMARY] GO ALTER TABLE [dbo].[TestTable] ADD DEFAULT (CURRENT_TIMESTAMP) FOR [Cold2] GO Now go to SSMS and generate the script for the table and you will notice following syntax. CREATE TABLE [dbo].[TestTable]( [Cold2] [datetime] NULL ) ON [PRIMARY] GO ALTER TABLE [dbo].[TestTable] ADD DEFAULT (GETDATE()) FOR [Cold2] GO You can notice that SQL Server have automatically converted CURRENT_TIMESTAMP to GETDATE(). I guess this gives us an idea how they behave. Now go ahead and make your choice! Do let me know which one will you use CURRENT_TIMESTAMP or GETDATE () in the comments area. Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: PostADay, SQL, SQL Authority, SQL DateTime, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology

  Read the article

• Automated build platform for .NET portfolio - best choice?

  - by jkohlhepp

  I am involved with maintaining a fairly large portfolio of .NET applications. Also in the portfolio are legacy applications built on top of other platforms - native C++, ECLIPS Forms, etc. I have a complex build framework on top of NAnt right now that manages the builds for all of these applications. The build framework uses NAnt to do a number of different things: Pull code out of Subversion, as well as create tags in Subversion Build the code, using MSBuild for .NET or other compilers for other platforms Peek inside AssemblyInfo files to increment version numbers Do deletes of certain files that shouldn't be included in builds / releases Releases code to deployment folders Zips code up for backup purposes Deploy Windows services; start and stop them Etc. Most of those things can be done with just NAnt by itself, but we did build a couple of extension tasks for NAnt to do some things that were specific to our environment. Also, most of those processes above are genericized and reused across a lot of our different application build scripts, so that we don't repeat logic. So it is not simple NAnt code, and not simple build scripts. There are dozens of NAnt files that come together to execute a build. Lately I've been dissatisfied with NAnt for a couple reasons: (1) it's syntax is just awful - programming languages on top of XML are really horrific to maintain, (2) the project seems to have died on the vine; there haven't been a ton of updates lately and it seems like no one is really at the helm. Trying to get it working with .NET 4 has cause some pain points due to this lack of activity. So, with all of that background out of the way, here's my question. Given some of the things that I want to accomplish based on that list above, and given that I am primarily in a .NET shop, but I also need to build non-.NET projects, is there an alternative to NAnt that I should consider switching to? Things on my radar include Powershell (with or without psake), MSBuild by itself, and rake. These all have pros and cons. For example, is MSBuild powerful enough? I remember using it years ago and it didn't seem to have as much power as NAnt. Do I really want to have my team learn Ruby just to do builds using rake? Is psake really mature enough of a project to pin my portfolio to? Is Powershell "too close to the metal" and I'll end up having to write my own build library akin to psake to use it on its own? Are there other tools that I should consider? If you were involved with maintaining a .NET portfolio of significant complexity, what build tool would you be looking at? What does your team currently use?

  Read the article

• Delegates in c#

  - by Jalpesh P. Vadgama

  I have used delegates in my programming since C# 2.0. But I have seen there are lots of confusion going on with delegates so I have decided to blog about it. In this blog I will explain about delegate basics and use of delegates in C#. What is delegate? We can say a delegate is a type safe function pointer which holds methods reference in object. As per MSDN it's a type that references to a method. So you can assign more than one methods to delegates with same parameter and same return type. Following is syntax for the delegate public delegate int Calculate(int a, int b); Here you can see the we have defined the delegate with two int parameter and integer parameter as return parameter. Now any method that matches this parameter can be assigned to above delegates. To understand the functionality of delegates let’s take a following simple example. using System; namespace Delegates { class Program { public delegate int CalculateNumber(int a, int b); static void Main(string[] args) { int a = 5; int b = 5; CalculateNumber addNumber = new CalculateNumber(AddNumber); Console.WriteLine(addNumber(5, 6)); Console.ReadLine(); } public static int AddNumber(int a, int b) { return a + b; } } } Here in the above code you can see that I have created a object of CalculateNumber delegate and I have assigned the AddNumber static method to it. Where you can see in ‘AddNumber’ static method will just return a sum of two numbers. After that I am calling method with the help of the delegates and printing out put to the console application. Now let’s run the application and following is the output as expected. That’s it. You can see the out put of delegates after adding a number. This delegates can be used in variety of scenarios. Like in web application we can use it to update one controls properties from another control’s action. Same you can also call a delegates whens some UI interaction done like button clicked. Hope you liked it. Stay tuned for more. In next post I am going to explain about multicast delegates. Till then happy programming.

  Read the article

• In the Mobile and Tablet World, How Much is Too Much?

  - by andrewbrust

  The week of April 26th was a huge one in the world of mobile and tablet devices,  There were so many individual developments, announcements and solidifications of strategy, it’s almost impossible to believe they occurred in the same month, let alone the same week. Things started with Apple and Gizmodo having a Law and Order moment over the latter’s procurement of what appears to be the former’s 4th gen iPhone prototype.  We found out on the 26th that Gizmodo blogger Jason Chen’s apartment was raided by police and, honestly, that was a bit much. But Apple didn’t stop there.  They also published Steve Job’s critique of Adobe Flash and his explanation of Cupertino’s embargo of Flash on iPhones, iPods and iPads.  If you ask me, this too, was a bit much. Apple finished up the week by releasing the 3G version of its iPad product to the US market. I like (iLike?) my WiFi iPad.  The idea of getting a version of it that required a second 3G service monthly subscription, is, well, a bit  much. Microsoft was in the news too.  It killed a project it hadn’t even acknowledged the existence of: the Courier tablet.  That’s a bit much too.  If a tree falls in the woods, and Microsoft says they can’t hear it anyway, could they really have chopped it down? Maybe Microsoft Research should have licensed some of Courier’s technology from other parts of Microsoft.  Then maybe they could have kept the product alive.  Ask HTC: they’re going to be licensing technology from Microsoft because Redmond insists that Google’s Android operating system infringes on certain of their patents.  And since HTC now builds a number of handsets on Android, instead of being beholden, as they once were, to Windows Mobile, that means they can keep making their products.  Why does HTC have to pay the royalties, and not Google?  Maybe Microsoft decided that going after GOOG would have been a bit much, even for them. The agreement came not a moment to soon: HTC released their “Droid Incredible” (that name’s a bit much), an Android 2.1 handset with amazing hardware and HTC’s own Sense UI, on April 30th (this past Friday). This phone is very well-reviewed.  Maybe that’s why Google basically decided to beg off introducing a version of its Nexus One phone (also manufactured by HTC) on the Verizon Wireless network.  Google backing down?  That’s incredible, if not also a bit much. And that brings us to HP.  Which this week announced its acquisition of Palm and its webOS mobile phone touch-oriented operating system.  HP also killed its own Slate initiative.  Apparently HP realized that Windows 7, even with a proprietary HP touch UI added on top, is no match for the iPad.  I’m guessing they think webOS might work a bit better,  And I’m wondering if HP even wants to use webOS for phone handsets, beyond the Pre and Pixi.  Using it just for slate devices would be a bit extreme, but maybe not too much. Honestly, this was not Microsoft’s best week.  It killed a project and a close partner did likewise.  Then that same partner bought a competing OS product, while another partner released their new product that uses yet another competing OS platform. What did Microsoft actually produce this past week? An update to its Windows Phone 7 developer tools that actually works with the version of Visual Studio 2010 released on April 12th, and the version of Silverlight released three days later. That took three weeks to get synced up, and that’s a bit much too. But at least it happened. Windows Phone 7 is Microsoft’s best hope for a comeback in the SmartPhone market and to offer a credible touch-based tablet device.  This week, two of Microsoft’s slate initiatives died, and its only mobile phone victory was around its competitor’s operating system.  I hope the new platform gets Redmond out of the PC ghetto and into the classes of device that get people really excited today.  If it can’t, that would be a bit much; probably too much.  And, as the signs at the Lonestar Cafe in NYC used to say, too much ain’t enough.

  Read the article

• Should I be put off a junior role that uses an online development test?

  - by Ninefingers

  I've applied for a junior development role, or rather been found by a recruiter looking for a developer. In order to get to a telephone interview stage I've been asked to sit one of those online coding assessments. This wasn't quite what I expected. I consider myself a fairly good developer for my age and experience, but I've no illusions about being Don Knuth or anything. The test was a series of incredibly obtuse questions asking about the results of various obscure evaluations. About 30 minutes in I was thinking to myself I hadn't intended to enter an obfuscated code contest/code golf exercise. After my last telephone interview I was asked to build something. I did. That seemed fair. Go away and work this out is more my in office experience of programming than "please evaluate this combination of lambdas, filters, maps, lists, tuples etc". So I'm a little put off, to be honest. I never claimed to know the language inside out or all the little corner cases. My questions, then: Should I be put off? Why? Why not? Are these kinds of tests what I should be expecting for junior roles? Should I learn stuff exam style? That seems to be the objective of these tests, for which you are timed and not supposed to use references or books? Normally, in the course of development I have a fairly good idea of basic types, rules, flow control and whatever. Occasionally I'll come up on something I need to use a regex for and have to go and remind myself of the exact piece of syntax I need if trying what I think should work doesn't. Or I'll come up against a module I've not used before and go and look it up. For example, if I wanted to write a server using sockets in C right now, I'd probably check the last piece of code I wrote doing that (and or the various books I have) and work from there. Chances are I probably couldn't do it exactly from scratch and from memory, although I can tell you you'd need a socket(), bind(), listen() and accept() call and you might also want select() depending on whether you intend to pthread_create or not. So I know what the calls are, but not their specific parameter list. What are your experiences if you are a recruiting manager? Are you after programmers who can quote you the API or do you not mind if your programmers have a few books on their desk and google function calls every so often?

  Read the article

• Au revoir, Python?

  - by GuySmiley

  I'm an ex-C++ programmer who's recently discovered (and fallen head-over-heels with) Python. I've taken some time to become reasonably fluent in Python, but I've encountered some troubling realities that may lead me to drop it as my language of choice, at least for the time being. I'm writing this in the hopes that someone out there can talk me out of it by convincing me that my concerns are easily circumvented within the bounds of the python universe. I picked up python while looking for a single flexible language that will allow me to build end-to-end working systems quickly on a variety of platforms. These include: - web services - mobile apps - cross-platform client apps for PC Development speed is more of a priority at the time-being than execution speed. However, in order to improve performance over time without requiring major re-writes or architectural changes I think it's imperative to be able to interface easily with Java. That way, I can use Java to optimize specific components as the application scales, without throwing away any code. As far as I can tell, my requirement for an enterprise-capable, platform-independent, fast language with a large developer base means it would have to be Java. .NET or C++ would not cut it due to their respective limitations. Also Java is clearly de rigeur for most mobile platforms. Unfortunately, tragically, there doesn't seem to be a good way to meet all these demands. Jython seems to be what I'm looking for in principle, except that it appears to be practically dead, with no one developing, supporting, or using it to any great degree. And also Jython seems too married to the Java libraries, as you can't use many of the CPython standard libraries with it, which has a major impact on the code you end up writing. The only other option that I can see is to use JPype wrapped in marshalling classes, which may work although it seems like a pain and I wonder if it would be worth it in the long run. On the other hand, everything I'm looking for seems to be readily available by using JRuby, which seems to be much better supported. As things stand, I think this is my best option. I'm sad about this because I absolutely love everything about Python, including the syntax. The perl-like constructs in Ruby just feel like such a step backwards to me in terms of readability, but at the end of the day most of the benefits of python are available in Ruby as well. So I ask you - am I missing something here? Much of what I've said is based on what I've read, so is this summary of the current landscape accurate, or is there some magical solution to the Python-Java divide that will snuff these concerns and allow me to comfortably stay in my happy Python place?

  Read the article

• How to Quickly Add Multiple IP Addresses to Windows Servers

  - by Sysadmin Geek

  If you have ever added multiple IP addresses to a single Windows server, going through the graphical interface is an incredible pain as each IP must be added manually, each in a new dialog box. Here’s a simple solution. Needless to say, this can be incredibly monotonous and time consuming if you are adding more than a few IP addresses. Thankfully, there is a much easier way which allows you to add an entire subnet (or more) in seconds. Adding an IP Address from the Command Line Windows includes the “netsh” command which allows you to configure just about any aspect of your network connections. If you view the accepted parameters using “netsh /?” you will be presented with a list of commands each which have their own list of commands (and so on). For the purpose of adding IP addresses, we are interested in this string of parameters: netsh interface ipv4 add address Note: For Windows Server 2003/XP and earlier, “ipv4″ should be replaced with just “ip” in the netsh command. If you view the help information, you can see the full list of accepted parameters but for the most part what you will be interested in is something like this: netsh interface ipv4 add address “Local Area Connection” 192.168.1.2 255.255.255.0 The above command adds the IP Address 192.168.1.2 (with Subnet Mask 255.255.255.0) to the connection titled “Local Area Network”. Adding Multiple IP Addresses at Once When we accompany a netsh command with the FOR /L loop, we can quickly add multiple IP addresses. The syntax for the FOR /L loop looks like this: FOR /L %variable IN (start,step,end) DO command So we could easily add every IP address from an entire subnet using this command: FOR /L %A IN (0,1,255) DO netsh interface ipv4 add address “Local Area Connection” 192.168.1.%A 255.255.255.0 This command takes about 20 seconds to run, where adding the same number of IP addresses manually would take significantly longer. A Quick Demonstration Here is the initial configuration on our network adapter: ipconfig /all Now run netsh from within a FOR /L loop to add IP’s 192.168.1.10-20 to this adapter: FOR /L %A IN (10,1,20) DO netsh interface ipv4 add address “Local Area Connection” 192.168.1.%A 255.255.255.0 After the above command is run, viewing the IP Configuration of the adapter now shows: Latest Features How-To Geek ETC How To Create Your Own Custom ASCII Art from Any Image How To Process Camera Raw Without Paying for Adobe Photoshop How Do You Block Annoying Text Message (SMS) Spam? How to Use and Master the Notoriously Difficult Pen Tool in Photoshop HTG Explains: What Are the Differences Between All Those Audio Formats? How To Use Layer Masks and Vector Masks to Remove Complex Backgrounds in Photoshop Bring Summer Back to Your Desktop with the LandscapeTheme for Chrome and Iron The Prospector – Home Dash Extension Creates a Whole New Browsing Experience in Firefox KinEmote Links Kinect to Windows Why Nobody Reads Web Site Privacy Policies [Infographic] Asian Temple in the Snow Wallpaper 10 Weird Gaming Records from the Guinness Book

  Read the article

• Using CTAS & Exchange Partition Replace IAS for Copying Partition on Exadata

  - by Bandari Huang

  Usage Scenario: Copy data&index from one partition to another partition in a partitioned table. Solution: Create a partition definition Copy data from one partition to another partiton by 'Insert as select (IAS)' Create a nonpartitioned table by 'Create table as select (CTAS)' Convert a nonpartitioned table into a partition of partitoned table by exchangng their data segments. Rebuild unusable index Exchange Partition Convertion Mutual convertion between a partition (or subpartition) and a nonpartitioned table Mutual convertion between a hash-partitioned table and a partition of a composite *-hash partitioned table Mutual convertiton a [range | list]-partitioned table into a partition of a composite *-[range | list] partitioned table. Exchange Partition Usage Scenario High-speed data loading of new, incremental data into an existing partitioned table in DW environment Exchanging old data partitions out of a partitioned table, the data is purged from the partitioned table without actually being deleted and can be archived separately Exchange Partition Syntax ALTER TABLE schema.table EXCHANGE [PARTITION|SUBPARTITION] [partition|subprtition] WITH TABLE schema.table [INCLUDE|EXCLUDING] INDEX [WITH|WITHOUT] VALIDATION UPDATE [INDEXES|GLOBAL INDEXES] INCLUDING | EXCLUDING INDEXES Specify INCLUDING INDEXES if you want local index partitions or subpartitions to be exchanged with the corresponding table index (for a nonpartitioned table) or local indexes (for a hash-partitioned table). Specify EXCLUDING INDEXES if you want all index partitions or subpartitions corresponding to the partition and all the regular indexes and index partitions on the exchanged table to be marked UNUSABLE. If you omit this clause, then the default is EXCLUDING INDEXES. WITH | WITHOUT VALIDATION Specify WITH VALIDATION if you want Oracle Database to return an error if any rows in the exchanged table do not map into partitions or subpartitions being exchanged. Specify WITHOUT VALIDATION if you do not want Oracle Database to check the proper mapping of rows in the exchanged table. If you omit this clause, then the default is WITH VALIDATION.  UPADATE INDEX|GLOBAL INDEX Unless you specify UPDATE INDEXES, the database marks UNUSABLE the global indexes or all global index partitions on the table whose partition is being exchanged. Global indexes or global index partitions on the table being exchanged remain invalidated. (You cannot use UPDATE INDEXES for index-organized tables. Use UPDATE GLOBAL INDEXES instead.) Exchanging Partitions&Subpartitions Notes Both tables involved in the exchange must have the same primary key, and no validated foreign keys can be referencing either of the tables unless the referenced table is empty.  When exchanging partitioned index-organized tables: – The source and target table or partition must have their primary key set on the same columns, in the same order. – If key compression is enabled, then it must be enabled for both the source and the target, and with the same prefix length. – Both the source and target must be index organized. – Both the source and target must have overflow segments, or neither can have overflow segments. Also, both the source and target must have mapping tables, or neither can have a mapping table. – Both the source and target must have identical storage attributes for any LOB columns. 

  Read the article

• The standards that fail us and the intellectual bubble

  - by Jeff

  There has been a great deal of noise in the techie community about standards, and a sudden and unexplainable hate for Flash. This noise isn't coming from consumers... the countless soccer moms, teens and your weird uncle Bob, it's coming from the people who build (or at least claim to build) the stuff those consumers consume. If you could survey the position of consumers on the topic, they'd likely tell you that they just want stuff on the Web to work.The noise goes something like this: Web standards are the correct and right thing to use across the Intertubes, and anything not a part of those standards (Flash) is bad. Furthermore, the more recent noise is centered around the idea that HTML 5, along with Javascript, is the right thing to use. The arguments against Flash are, well, the truth is I haven't seen a good argument. I see anecdotal nonsense about high CPU usage and things I'd never think to check when I'm watching Piano Cat on YouTube, but these aren't arguments to me. Sure, I've seen it crash a browser a few times, but it's totally rare.But let's go back to standards. Yes, standards have played an important role in establishing the ubiquity of the Web. The protocols themselves, TCP/IP and HTTP, have been critical. HTML, which has served us well for a very long time, established an incredible foundation. Javascript did an OK job, and thanks to clever programmers writing great frameworks like JQuery, is becoming more and more useful. CSS is awful (there, I said it, I feel SO much better), and I'll never understand why it's so disconnected and different from anything else. It doesn't help that it's so widely misinterpreted by different browsers. Still, there's no question that standards are a good thing, and they've been good for the Web, consumers and publishers alike.HTML 4 has been with us for more than a decade. In Web years, that might as well be 80. HTML 5, contrary to popular belief, is not a standard, and likely won't be for many years to come. In fact, the Web hasn't really evolved at all in terms of its standards. The tools that generate the standard markup and script have, but at the end of the day, we're still living with standards that are more than ten years old. The "official" standards process has failed us.The Web evolved anyway, and did not wait for standards bodies to decide what to do next. It evolved in part because Macromedia, then Adobe, kept evolving Flash. In the earlier days, it mostly just did obnoxious splash pages, but then it started doing animation, and then rich apps as they added form input. Eventually it found its killer app: video. Now more than 95% of browsers have Flash installed. Consumers are better for it.But I'll do it one better... I'll go out on a limb and say that Flash is a standard. If it's that pervasive, I don't care what you tell me, it's a standard. Just because a company owns it doesn't mean that it's evil or not a standard. And hey, it pains me to say that as a developer, because I think the dev tools are the suck (more on that in a minute). But again, consumers don't care. They don't even pay for Flash. The bottom line is that if I put something Flash based on the Internet, it's likely that my audience will see it.And what about the speed of standards owned by a company? Look no further than Silverlight. Silverlight 2 (which I consider the "real" start to the story) came out about a year and a half ago. Now version 4 is out, and it has come a very long way in its capabilities. If you believe Riastats.com, more than half of browsers have it now. It didn't have to wait for standards bodies and nerds drafting documents, it's out today. At this rate, Silverlight will be on version 6 or 7 by the time HTML 5 is a ratified standard.Back to the noise, one of the things that has continually disappointed me about this profession is the number of people who get stuck in an intellectual bubble, color it with dogmatic principles, and completely ignore the actual marketplace where this stuff all has to live. We aren't machines; Binary thinking that forces us to choose between "open standards" and "proprietary lock-in" (the most loaded b.s. FUD term evar) isn't smart at all. The truth is that the <object> tag has allowed us to build incredible stuff on top of the old standards, and consumers have benefitted greatly. Consumer desire, capitalism, and yes, standards ratified by nerds who think about this stuff for years have all played a role in the broad adoption of the Interwebs.We could all do without the noise. At the end of the day, I'm going to build stuff for the Web that's good for my users, and I'm not going to base my decisions on a techie bubble religion. Imagine what the brilliant minds behind the noise could do for the Web if they joined me in that pursuit.

  Read the article

• Cant get lm-sensors to load ATI Radeon temp and fan or output all settings

  - by woody

  New to Linux and having minor issues :/ . I followed this guide initially but did not recieve the proper output and did not show my ATI Radeon HD 5000 temp or fan speed. Then used this guide, same problems exhibited. No issues installing and no errors. I think its not reading i2c for some reason. The proprietary driver is installed and functioning correctly according fglrxinfo. I can use aticonfig commands and view both temp and fan. Any ideas on how to get the ATI Radeon sensors working under 'sensors'? When i run 'sudo sensors-detect' this is my ouput # sensors-detect revision 5984 (2011-07-10 21:22:53 +0200) # System: LENOVO IdeaPad Y560 (laptop) # Board: Lenovo KL3 This program will help you determine which kernel modules you need to load to use lm_sensors most effectively. It is generally safe and recommended to accept the default answers to all questions, unless you know what you're doing. Some south bridges, CPUs or memory controllers contain embedded sensors. Do you want to scan for them? This is totally safe. (YES/no): y Silicon Integrated Systems SIS5595... No VIA VT82C686 Integrated Sensors... No VIA VT8231 Integrated Sensors... No AMD K8 thermal sensors... No AMD Family 10h thermal sensors... No AMD Family 11h thermal sensors... No AMD Family 12h and 14h thermal sensors... No AMD Family 15h thermal sensors... No AMD Family 15h power sensors... No Intel digital thermal sensor... Success! (driver `coretemp') Intel AMB FB-DIMM thermal sensor... No VIA C7 thermal sensor... No VIA Nano thermal sensor... No Some Super I/O chips contain embedded sensors. We have to write to standard I/O ports to probe them. This is usually safe. Do you want to scan for Super I/O sensors? (YES/no): y Probing for Super-I/O at 0x2e/0x2f Trying family `National Semiconductor/ITE'... Yes Found unknown chip with ID 0x8502 Probing for Super-I/O at 0x4e/0x4f Trying family `National Semiconductor/ITE'... No Trying family `SMSC'... No Trying family `VIA/Winbond/Nuvoton/Fintek'... No Trying family `ITE'... No Some hardware monitoring chips are accessible through the ISA I/O ports. We have to write to arbitrary I/O ports to probe them. This is usually safe though. Yes, you do have ISA I/O ports even if you do not have any ISA slots! Do you want to scan the ISA I/O ports? (YES/no): y Probing for `National Semiconductor LM78' at 0x290... No Probing for `National Semiconductor LM79' at 0x290... No Probing for `Winbond W83781D' at 0x290... No Probing for `Winbond W83782D' at 0x290... No Lastly, we can probe the I2C/SMBus adapters for connected hardware monitoring devices. This is the most risky part, and while it works reasonably well on most systems, it has been reported to cause trouble on some systems. Do you want to probe the I2C/SMBus adapters now? (YES/no): y Using driver `i2c-i801' for device 0000:00:1f.3: Intel 3400/5 Series (PCH) Now follows a summary of the probes I have just done. Just press ENTER to continue: Driver `coretemp': * Chip `Intel digital thermal sensor' (confidence: 9) To load everything that is needed, add this to /etc/modules: #----cut here---- # Chip drivers coretemp #----cut here---- If you have some drivers built into your kernel, the list above will contain too many modules. Skip the appropriate ones! Do you want to add these lines automatically to /etc/modules? (yes/NO) My output for 'sensors' is: acpitz-virtual-0 Adapter: Virtual device temp1: +58.0°C (crit = +100.0°C) coretemp-isa-0000 Adapter: ISA adapter Core 0: +56.0°C (high = +84.0°C, crit = +100.0°C) Core 1: +57.0°C (high = +84.0°C, crit = +100.0°C) Core 2: +58.0°C (high = +84.0°C, crit = +100.0°C) Core 3: +57.0°C (high = +84.0°C, crit = +100.0°C) and my '/etc/modules' is: # /etc/modules: kernel modules to load at boot time. # # This file contains the names of kernel modules that should be loaded # at boot time, one per line. Lines beginning with "#" are ignored. lp rtc # Generated by sensors-detect on Fri Nov 30 23:24:31 2012 # Chip drivers coretemp

  Read the article

• Windows Azure Recipe: Software as a Service (SaaS)

  - by Clint Edmonson

  The cloud was tailor built for aspiring companies to create innovative internet based applications and solutions. Whether you’re a garage startup with very little capital or a Fortune 1000 company, the ability to quickly setup, deliver, and iterate on new products is key to capturing market and mind share. And if you can capture that share and go viral, having resiliency and infinite scale at your finger tips is great peace of mind. Drivers Cost avoidance Time to market Scalability Solution Here’s a sketch of how a basic Software as a Service solution might be built out: Ingredients Web Role – this hosts the core web application. Each web role will host an instance of the software and as the user base grows, additional roles can be spun up to meet demand. Access Control – this service is essential to managing user identity. It’s backed by a full blown implementation of Active Directory and allows the definition and management of users, groups, and roles. A pre-built ASP.NET membership provider is included in the training kit to leverage this capability but it’s also flexible enough to be combined with external Identity providers including Windows LiveID, Google, Yahoo!, and Facebook. The provider model provides extensibility to hook into other industry specific identity providers as well. Databases – nearly every modern SaaS application is backed by a relational database for its core operational data. If the solution is sold to organizations, there’s a good chance multi-tenancy will be needed. An emerging best practice for SaaS applications is to stand up separate SQL Azure database instances for each tenant’s proprietary data to ensure isolation from other tenants. Worker Role – this is the best place to handle autonomous background processing such as data aggregation, billing through external services, and other specialized tasks that can be performed asynchronously. Placing these tasks in a worker role frees the web roles to focus completely on user interaction and data input and provides finer grained control over the system’s scalability and throughput. Caching (optional) – as a web site traffic grows caching can be leveraged to keep frequently used read-only, user specific, and application resource data in a high-speed distributed in-memory for faster response times and ultimately higher scalability without spinning up more web and worker roles. It includes a token based security model that works alongside the Access Control service. Blobs (optional) – depending on the nature of the software, users may be creating or uploading large volumes of heterogeneous data such as documents or rich media. Blob storage provides a scalable, resilient way to store terabytes of user data. The storage facilities can also integrate with the Access Control service to ensure users’ data is delivered securely. Training & Examples These links point to online Windows Azure training labs and examples where you can learn more about the individual ingredients described above. (Note: The entire Windows Azure Training Kit can also be downloaded for offline use.) Windows Azure (16 labs) Windows Azure is an internet-scale cloud computing and services platform hosted in Microsoft data centers, which provides an operating system and a set of developer services which can be used individually or together. It gives developers the choice to build web applications; applications running on connected devices, PCs, or servers; or hybrid solutions offering the best of both worlds. New or enhanced applications can be built using existing skills with the Visual Studio development environment and the .NET Framework. With its standards-based and interoperable approach, the services platform supports multiple internet protocols, including HTTP, REST, SOAP, and plain XML SQL Azure (7 labs) Microsoft SQL Azure delivers on the Microsoft Data Platform vision of extending the SQL Server capabilities to the cloud as web-based services, enabling you to store structured, semi-structured, and unstructured data. Windows Azure Services (9 labs) As applications collaborate across organizational boundaries, ensuring secure transactions across disparate security domains is crucial but difficult to implement. Windows Azure Services provides hosted authentication and access control using powerful, secure, standards-based infrastructure. Developing Applications for the Cloud, 2nd Edition (eBook) This book demonstrates how you can create from scratch a multi-tenant, Software as a Service (SaaS) application to run in the cloud using the latest versions of the Windows Azure Platform and tools. The book is intended for any architect, developer, or information technology (IT) professional who designs, builds, or operates applications and services that run on or interact with the cloud. Fabrikam Shipping (SaaS reference application) This is a full end to end sample scenario which demonstrates how to use the Windows Azure platform for exposing an application as a service. We developed this demo just as you would: we had an existing on-premises sample, Fabrikam Shipping, and we wanted to see what it would take to transform it in a full subscription based solution. The demo you find here is the result of that investigation See my Windows Azure Resource Guide for more guidance on how to get started, including more links web portals, training kits, samples, and blogs related to Windows Azure.

  Read the article

• TechEd 2010 Day Three: The Database Designer (Isn't)

  - by BuckWoody

  Yesterday at TechEd 2010 here in New Orleans I worked the front-booth, answering general SQL Server questions for the masses. I was actually a little surprised to find most of the questions I got were from folks that wanted to know more about Stream Insight and Master Data Services. In past conferences I've been asked a lot of "free consulting" questions, about problems folks have had from older products. I don't mind that a bit - in fact, I'm always happy to help in any way I can. But this time people are really interested in the new features in the product, and I like that they are thinking ahead, not just having to solve problems in production. My presentation was on "Database Design in an Hour". We had the usual fun, and SideShow Bob made an appearance - I kid you not. The guy in the back of the room looked just like Sideshow Bob, so I quickly held a "bes thair" contest, and he won. Duing the presentation, I explain the tools you can use to design databases. I also explain that the "Database Designer" tool in SQL Server Management Studio (SSMS) isn't truly a desinger - it uses non-standard notation, doesn't have a meta-data dictionary, and worst of all, it works at the physical level. In other words, whatever you do in SSMS will automatically change the field/table/relationship structures in the database. We fixed this in SSMS 2008 and higher by adding an option to block that, but the tool is not a good design function nonetheless. To be fair, no one I know of at Microsoft recommends that it is - but I was shocked to hear so many developers in the room defending it as a good tool. I think the main issue for someone who doesn't have to work with Relational Systems a great deal is that it can be difficult to figure out Foreign Keys. The syntax makes them look "backwards", so it's just easier to grab a field and place it on the table you want to point to. There are options. You can download a couple of free tools (CA has a community edition of ER-WIN, Quest has one, and Embarcadero also has one) and if you design more than one or two databases a year, it may be worth buying a true design tool. For years I used Visio, but we changed it so that it doesn't forward-engineer (create the DDL) any more, so it isn't a true design tool either. So investigate those free and not-so-free tools. You'll find they help you in your job - but stay away from the Database Designer in SSMS. Or I'll send Sideshow Bob over there to straighten you out. Share this post: email it! | bookmark it! | digg it! | reddit! | kick it! | live it!

  Read the article

• A big flat text file or a HTML site for language documentation?

  - by Bad Sector

  A project of mine is a small embeddable Tcl-like scripting language, LIL. While i'm mostly making it for my own use, i think it is interesting enough for others to use, so i want it to have a nice (but not very "wordy") documentation. So far i'm using a single flat readme.txt file. It explains the language's syntax, features, standard functions, how to use the C API, etc. Also it is easy to scan and read in almost every environment out there, from basic text-only terminals to full-fledged high-end graphical desktop environments. However, while i tried to keep things nicely formatted (as much as this is possible in plain text), i still think that being a big (and growing) wall of text, it isn't as easy on the eyes as it could be. Also i feel that sometimes i'm not writing as much as i want in order to avoid expanding the text too much. So i thought i could use another project of mine, QuHelp, which is basically a help site generator for sites like this one with a sidebar that provides a tree of topics/subtopics and offline full text search. With this i can use HTML to format the documentation and if i use QuHelp for some other project that uses LIL, i can import LIL's documentation as part of the other project's documentation. However converting the existing documentation to QuHelp/HTML isn't a small task, especially when it comes to functions (i'll need to put more detail on them than what currently exists in the readme.txt file). Also it loses the wide range of availability that it currently has (even if QuHelp's generated code degrades gracefully down to console-only web browsers, plain text is readable from everywhere, including from popular editors such as Vim and Emacs - i had someone once telling me that he likes LIL's documentation because it is readable without leaving his editor). So, my question is simply this: should i keep the documentation as it is now in the form of a single readme.txt file or should i convert it to something like the site i mentioned above? There is also the option to do both, but i'm not sure if i'll be able to always keep them in sync or if it is worth the effort. After asking around in IRC i've got mixed answers: some liked the wide availability of the single text file, others said that it is looks as bad as a man page (personally i don't mind that - i can read man pages just fine - but other people might have issues reading them). What do you think?

  Read the article

• BPM ADF Task forms. Checking whether the current user is in a BPM Swimlane

  - by Christopher Karl Chan

  @page { margin: 0.79in } P { margin-bottom: 0.08in } --Focus So this blog entry will focus on BPM Swimlane roles and users from a ADF context. So we have an ADF Task Details Form and we are in the process of making it richer and dynamic in functionality. A common requirement could be to dynamically show different areas based on the user logged into the workspace. Perhaps even we want to know even what swim-lane role the user belongs to. It is is a little bit harder to achieve then one thinks unless you know the trick. The Challenge The tricky part here is that the ADF Task Details Form is in fact part of a separate J2EE application to the main workspace. So if you try to use Java or Expression Language to get the logged in user you will only find anonymous and none of the BPM Roles you will be expecting. So what to do? The Magic First add the BC4J Security library to your view project. Then Restart JDeveloper. Now find the web.xml file in the view project of your ADF Task Details Application and look for the JpsFilter section. Then add in the following section. <init-param> <param-name>application.name</param-name> <param-value>OracleBPMProcessRolesApp</param-value></init-param> This will link your application to that of the BPM workspace. Then in your dynamic part of your ADF form you can now check whether the user logged into the BPM Workspace belongs in a BPM swim-lane in any BPM process. The best way to do this is by using expression language in the JSF page itself. Here I am simply changing the rendered flag to either true or false and thereby hiding or showing a section. Perhaps you are re-using the same form for a task in an approver swim-lane and ordinary user swimlane. So we only want the approver to see this field. So call the built in function to check if the user is a member of the BPM swim-lane role. The name of the role must be of the syntax BPMProject.RoleName <af:outputText value="This will only be rendered when the user is part of the BPM Swimlane Role rendered="#{securityContext.userInRole['BPMProjectName.Rolename']}"/> Now you must redeploy your ADF Task Form project Now (in the image above) the text will ONLY get rendered in the Task Details Form only if the user logged into the workspace is a member of the swimlane Unsecure of the BPM project SimpleTask

  Read the article

• Selectively Exposing Functionallity in .Net

  - by David V. Corbin

  Any developer should be aware of the principles of encapsulation, cross-tier isolation, and cross-functional separation of concerns. However, it seems the few take the time to consider the adage of "minimal yet complete"1 when developing the software. Consider the exposure of "business objects" to the user interface. Some common situations occur: Accessing a given element requires a compound set of calls that do not "make sense" to the User Interface. More information than absolutely required is exposed to the user interface It would be much cleaner if a custom interface was provided that exposed exactly (and only) the information that is required by the consumer. Achieving this using conventional techniques would require the creation (and maintenance!) of custom classes to filter and transpose the information into the ideal format. Determining the ROI on this approach can be very difficult to ascertain, and as a result it is often ignored completely. There is another approach, which is largely made practical by virtual of the Action and Func delegates. From a callers point of view, the following two samples can be used interchangeably:     interface ISomeInterface     {         void SampleMethod1(string param);         string SamepleMethod2(string param);     }       class ISomeInterface     {         public Action<string> SampleMethod1 {get; }         public Func<string,string> SamepleMethod2 {get; }     }   The capabilities this simple changes enable are significant (and remember it does not cange the syntax at the call site): The delegates can be initialized to directly call the proper method of any target class. The delegates can be dynamically updated based on the current state. The "interface" can NOT be cast to the concrete class (which often exposes more functionallity). This patterns By limiting the interface to the exact functionallity required, the reduced surface area will typically result in lower development, testing and maintenance costs. We are currently in the process of posting a project on CodePlex which illustrates this (and many other) techniques which have proven helpful in creating robust yet flexible solutions that are highly efficient2 and maintainable. This post will be updated as soon as the project is published. 1) Credit: Scott  Meyers, Effective C++, Addison-Wesley 1992 2) For those who read my previous post on performance it should be noted that the use of delegates is on the same order of magnitude (actually a tiny amount faster) as conventional interfaces.

  Read the article

• Is there a better term than "smoothness" or "granularity" to describe this language feature?

  - by Chris

  One of the best things about programming is the abundance of different languages. There are general purpose languages like C++ and Java, as well as little languages like XSLT and AWK. When comparing languages, people often use things like speed, power, expressiveness, and portability as the important distinguishing features. There is one characteristic of languages I consider to be important that, so far, I haven't heard [or been able to come up with] a good term for: how well a language scales from writing tiny programs to writing huge programs. Some languages make it easy and painless to write programs that only require a few lines of code, e.g. task automation. But those languages often don't have enough power to solve large problems, e.g. GUI programming. Conversely, languages that are powerful enough for big problems often require far too much overhead for small problems. This characteristic is important because problems that look small at first frequently grow in scope in unexpected ways. If a programmer chooses a language appropriate only for small tasks, scope changes can require rewriting code from scratch in a new language. And if the programmer chooses a language with lots of overhead and friction to solve a problem that stays small, it will be harder for other people to use and understand than necessary. Rewriting code that works fine is the single most wasteful thing a programmer can do with their time, but using a bazooka to kill a mosquito instead of a flyswatter isn't good either. Here are some of the ways this characteristic presents itself. Can be used interactively - there is some environment where programmers can enter commands one by one Requires no more than one file - neither project files nor makefiles are required for running in batch mode Can easily split code across multiple files - files can refeence each other, or there is some support for modules Has good support for data structures - supports structures like arrays, lists, and especially classes Supports a wide variety of features - features like networking, serialization, XML, and database connectivity are supported by standard libraries Here's my take on how C#, Python, and shell scripting measure up. Python scores highest. Feature C# Python shell scripting --------------- --------- --------- --------------- Interactive poor strong strong One file poor strong strong Multiple files strong strong moderate Data structures strong strong poor Features strong strong strong Is there a term that captures this idea? If not, what term should I use? Here are some candidates. Scalability - already used to decribe language performance, so it's not a good idea to overload it in the context of language syntax Granularity - expresses the idea of being good just for big tasks versus being good for big and small tasks, but doesn't express anything about data structures Smoothness - expresses the idea of low friction, but doesn't express anything about strength of data structures or features Note: Some of these properties are more correctly described as belonging to a compiler or IDE than the language itself. Please consider these tools collectively as the language environment. My question is about how easy or difficult languages are to use, which depends on the environment as well as the language.

  Read the article

• Apache2 Syntex, cant acces 000-default

  - by enrique2334

  I have been using Apache2 and webmin with my raspberry pi. after a restart and reinstalations apache wont start. > sudo /etc/init.d/apache2 restart apache2: Syntax error on line 268 of /etc/apache2/apache2.conf: Could not open configuration file /etc/apache2/sites-enabled/000-default: No such file or directory Action 'configtest' failed. The Apache error log may have more information. failed! The file 000-default is there and unopenable permisions to root-root My apache2.conf file looks like this (bottom half) # ErrorLog: The location of the error log file. # If you do not specify an ErrorLog directive within a <VirtualHost> # container, error messages relating to that virtual host will be # logged here. If you *do* define an error logfile for a <VirtualHost> # container, that host's errors will be logged there and not here. # ErrorLog ${APACHE_LOG_DIR}/error.log # # LogLevel: Control the number of messages logged to the error_log. # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. # LogLevel debug # Include module configuration: Include mods-enabled/*.load Include mods-enabled/*.conf # Include list of ports to listen on and which to use for name based vhosts Include ports.conf # # The following directives define some format nicknames for use with # a CustomLog directive (see below). # If you are behind a reverse proxy, you might want to change %h into %{X-Forwarded-For}i # LogFormat "%v:%p %h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" vhost_combined LogFormat "%h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %O" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent # Include of directories ignores editors' and dpkg's backup files, # see the comments above for details. # Include generic snippets of statements Include conf.d/ # Include the virtual host configurations: Include sites-enabled/ <VirtualHost *:80> DocumentRoot /var/www <Directory /var/www> allow from all Options +Indexes </Directory> ServerName IMASERVER </VirtualHost> does anyone know what the cause of this?

  Read the article

• ODI 11g - Cleaning control characters and User Functions

  - by David Allan

  In ODI user functions have a poor name really, they should be user expressions - a way of wrapping common expressions that you may wish to reuse many times - across many different technologies is an added bonus. To illustrate look at the problem of how to remove control characters from text. Users ask these types of questions over all technologies - Microsoft SQL Server, Oracle, DB2 and for many years - how do I clean a string, how do I tokenize a string and so on. After some searching around you will find a few ways of doing this, in Oracle there is a convenient way of using the TRANSLATE and REPLACE functions. So you can convert some text using the following SQL; replace( translate('This is my string'||chr(9)||' which has a control character', chr(3)||chr(4)||chr(5)||chr(9), chr(3) ), chr(3), '' ) If you had many columns to perform this kind of transformation on, in the Oracle database the natural solution you'd go to would be to code this as a PLSQL function since you don't want the code splattered everywhere. Someone tells you that there is another control character that needs added equals a maintenance headache. Coding it as a PLSQL function will incur a context switch between SQL and PLSQL which could prove costly. In ODI user functions let you capture this expression text and reference it many times across your mappings. This will protect the expression from being copy-pasted by developers and make maintenance much simpler - change the expression definition in one place. Firstly define a name and a syntax for the user function, I am calling it UF_STRIP_BAD_CHARACTERS and it has one parameter an input string;  We then can define an implementation for each technology we will use it, I will define Oracle's using the inputString parameter and the TRANSLATE and REPLACE functions with whatever control characters I want to replace; I can then use this inside mapping expressions in ODI, below I am cleaning the ENAME column - a fabricated example but you get the gist.  Note when I use the user function the function name remains in the text of the mapping, the actual expression is not substituted until I generate the scenario. If you generate the scenario and export the scenario you can have a peak at the code that is processed in the runtime - below you can see a snippet of my export scenario;  That's all for now, hopefully a useful snippet of info.

  Read the article

• What Keeps You from Changing Your Public IP Address and Wreaking Havoc on the Internet?

  - by Jason Fitzpatrick

  What exactly is preventing you (or anyone else) from changing their IP address and causing all sorts of headaches for ISPs and other Internet users? Today’s Question & Answer session comes to us courtesy of SuperUser—a subdivision of Stack Exchange, a community-driven grouping of Q&A web sites. The Question SuperUser reader Whitemage is curious about what’s preventing him from wantonly changing his IP address and causing trouble: An interesting question was asked of me and I did not know what to answer. So I’ll ask here. Let’s say I subscribed to an ISP and I’m using cable internet access. The ISP gives me a public IP address of 60.61.62.63. What keeps me from changing this IP address to, let’s say, 60.61.62.75, and messing with another consumer’s internet access? For the sake of this argument, let’s say that this other IP address is also owned by the same ISP. Also, let’s assume that it’s possible for me to go into the cable modem settings and manually change the IP address. Under a business contract where you are allocated static addresses, you are also assigned a default gateway, a network address and a broadcast address. So that’s 3 addresses the ISP “loses” to you. That seems very wasteful for dynamically assigned IP addresses, which the majority of customers are. Could they simply be using static arps? ACLs? Other simple mechanisms? Two things to investigate here, why can’t we just go around changing our addresses, and is the assignment process as wasteful as it seems? The Answer SuperUser contributor Moses offers some insight: Cable modems aren’t like your home router (ie. they don’t have a web interface with simple point-and-click buttons that any kid can “hack” into). Cable modems are “looked up” and located by their MAC address by the ISP, and are typically accessed by technicians using proprietary software that only they have access to, that only runs on their servers, and therefore can’t really be stolen. Cable modems also authenticate and cross-check settings with the ISPs servers. The server has to tell the modem whether it’s settings (and location on the cable network) are valid, and simply sets it to what the ISP has it set it for (bandwidth, DHCP allocations, etc). For instance, when you tell your ISP “I would like a static IP, please.”, they allocate one to the modem through their servers, and the modem allows you to use that IP. Same with bandwidth changes, for instance. To do what you are suggesting, you would likely have to break into the servers at the ISP and change what it has set up for your modem. Could they simply be using static arps? ACLs? Other simple mechanisms? Every ISP is different, both in practice and how close they are with the larger network that is providing service to them. Depending on those factors, they could be using a combination of ACL and static ARP. It also depends on the technology in the cable network itself. The ISP I worked for used some form of ACL, but that knowledge was a little beyond my paygrade. I only got to work with the technician’s interface and do routine maintenance and service changes. What keeps me from changing this IP address to, let’s say, 60.61.62.75 and mess with another consumer’s internet access? Given the above, what keeps you from changing your IP to one that your ISP hasn’t specifically given to you is a server that is instructing your modem what it can and can’t do. Even if you somehow broke into the modem, if 60.61.62.75 is already allocated to another customer, then the server will simply tell your modem that it can’t have it. David Schwartz offers some additional insight with a link to a white paper for the really curious: Most modern ISPs (last 13 years or so) will not accept traffic from a customer connection with a source IP address they would not route to that customer were it the destination IP address. This is called “reverse path forwarding”. See BCP 38. Have something to add to the explanation? Sound off in the the comments. Want to read more answers from other tech-savvy Stack Exchange users? Check out the full discussion thread here.     

  Read the article

• WebLogic Server Weekly for March 26th, 2012: WLS 1211 Update, Java 7 Certification, Galleria, WebLogic for DBAs, REST and Enterprise Architecture, Singleton Services

  - by Steve Button

  WebLogic Server 12c Certified with Java 7 for Production Use WebLogic Server 12c (12.1.1) has been certified with JDK 7 for development usage since December and we have now completed JDK 7 certification for use with production systems. In doing so, we have updated the WebLogic Server 12c (12.1.1) distributions incorporating fixes associated with JDK 7 support as well as some bundled patches that address several issues that have been discovered since the initial release. These updated distributions are available for download from OTN and will be beneficial for all WebLogic Server 12c (12.1.1) users in general. What's New Release Notes Download Here! Updated Oracle WebLogic Server 12.1.1.0 distribution Never one to miss a trick, Markus Eisele was one of the first to notice the WebLogic Server 12c update and post a blog about it. Sources told me that as of Friday last week you have an updated version of WebLogic Server 12c on OTN. http://blog.eisele.net/2012/03/updated-oracle-weblogic-server-12110.html Using WebLogic Server 12c with Java 7 - Video To illustrate the use of Java 7 with WebLogic Server 12c, I put together a screen cam showing the creation of a domain using Java 7 and then build and deploy a simple web application that uses Java 7 syntax to show it working. Ireland OUG Presentation: WebLogic for DBAs Simon Haslam posted his slides from a presentation he gave Dublin on 21/3/12 at the OUG Ireland conference. In this presentation, he explains the core concepts and ideas behind WebLogic Server, walks through an installation and offers some tips and common gotcha's to avoid. Simon also covers some aspects of installing and use Enterprise Manager 12c. Note: I usually install the JVM and use the generic .jar installer rather than using an installer bundled with a JVM. http://www.slideshare.net/Veriton/weblogic-for-dbas-10h Slightly Retro: Jeff West on Enterprise Architecure and REST In this weeks flashback, we look at Jeff West's blog from early 2011 where he provides some thoughtful opinions on enterprise architecture and innovation, then jumps into his views on REST. After I progressed in my career and did more team-leading and architecture type roles I was ‘educated’ on what it meant to have Asynchronous and Long-Running processes as part of your Enterprise Application architecture. If I had a synchronous process then I needed a thread available to service the request and then provide the response. https://blogs.oracle.com/jeffwest/entry/weblogic_integration_wli_web_services_and_soap_and_rest_part_1 Starting Managed Servers without an Administration Server using Node Manager and WLST Blogger weblogic-tips shows how to start a managed server without going through the Administration Server, using the Node Manager and WLST. Connect WLST to a Node Manager by entering the nmConnect command. http://www.weblogic-tips.com/2012/02/18/starting-managed-servers-without-an-administration-server-using-node-manager-and-wlst/ Using WebLogic Server Singleton Services WebLogic Server has supported the notion of a Singleton Service for a number of releases, in which WebLogic Server will maintain a single instance of a configured singleton service on one managed server within a cluster. This blog demonstrates how the singleton service can be accessed and used from applications deployed on the cluster. http://buttso.blogspot.com.au/2012/03/weblogic-server-singleton-services.html

  Read the article

• Library to fake intermittent failures according to tester-defined policy?

  - by crosstalk

  I'm looking for a library that I can use to help mock a program component that works only intermittently - usually, it works fine, but sometimes it fails. For example, suppose I need to read data from a file, and my program has to avoid crashing or hanging when a read fails due to a disk head crash. I'd like to model that by having a mock data reader function that returns mock data 90% of the time, but hangs or returns garbage otherwise. Or, if I'm stress-testing my full program, I could turn on debugging code in my real data reader module to make it return real data 90% of the time and hang otherwise. Now, obviously, in this particular example I could just code up my mock manually to test against a random() routine. However, I was looking for a system that allows implementing any failure policy I want, including: Fail randomly 10% of the time Succeed 10 times, fail 4 times, repeat Fail semi-randomly, such that one failure tends to be followed by a burst of more failures Any policy the tester wants to define Furthermore, I'd like to be able to change the failure policy at runtime, using either code internal to the program under test, or external knobs or switches (though the latter can be implemented with the former). In pig-Java, I'd envision a FailureFaker interface like so: interface FailureFaker { /** Return true if and only if the mocked operation succeeded. Implementors should override this method with versions consistent with their failure policy. */ public boolean attempt(); } And each failure policy would be a class implementing FailureFaker; for example there would be a PatternFailureFaker that would succeed N times, then fail M times, then repeat, and a AlwaysFailFailureFaker that I'd use temporarily when I need to simulate, say, someone removing the external hard drive my data was on. The policy could then be used (and changed) in my mock object code like so: class MyMockComponent { FailureFaker faker; public void doSomething() { if (faker.attempt()) { // ... } else { throw new RuntimeException(); } } void setFailurePolicy (FailureFaker policy) { this.faker = policy; } } Now, this seems like something that would be part of a mocking library, so I wouldn't be surprised if it's been done before. (In fact, I got the idea from Steve Maguire's Writing Solid Code, where he discusses this exact idea on pages 228-231, saying that such facilities were common in Microsoft code of that early-90's era.) However, I'm only familiar with EasyMock and jMockit for Java, and neither AFAIK have this function, or something similar with different syntax. Hence, the question: Do such libraries as I've described above exist? If they do, where have you found them useful? If you haven't found them useful, why not?

  Read the article

• Backup Azure Tables with the Enzo Backup API

  - by Herve Roggero

  In case you missed it, you can now backup (and restore) Azure Tables and SQL Databases using an API directly. The features available through the API can be found here: http://www.bluesyntax.net/backup20api.aspx and the online help for the API is here: http://www.bluesyntax.net/EnzoCloudBackup20/APIIntro.aspx. Backing up Azure Tables can’t be any easier than with the Enzo Backup API. Here is a sample code that does the trick: // Create the backup helper class. The constructor automatically sets the SourceStorageAccount property StorageBackupHelper backup = new StorageBackupHelper("storageaccountname", "storageaccountkey", "sourceStorageaccountname", "sourceStorageaccountkey", true, "apilicensekey"); // Now set some properties… backup.UseCloudAgent = false;                                       // backup locally backup.DeviceURI = @"c:\TMP\azuretablebackup.bkp";    // to this file backup.Override = true; backup.Location = DeviceLocation.LocalFile; // Set optional performance options backup.PKTableStrategy.Mode = BSC.Backup.API.TableStrategyMode.GUID; // Set GUID strategy by default backup.MaxRESTPerSec = 200; // Attempt to stay below 200 REST calls per second // Start the backup now… string taskId = backup.Backup(); // Use the Environment class to get the final status of the operation EnvironmentHelper env = new EnvironmentHelper("storageaccountname", "storageaccountkey", "apilicensekey"); string status = env.GetOperationStatus(taskId);   As you can see above, the code is straightforward. You provide connection settings in the constructor, set a few options indicating where the backup device will be located, set optional performance parameters and start the backup. The performance options are designed to help you backup your Azure Tables quickly, while attempting to keep under a specific threshold to prevent Storage Account throttling. For example, the MaxRESTPerSec property will attempt to keep the overall backup operation under 200 rest calls per second. Another performance option if the Backup Strategy for Azure Tables. By default, all tables are simply scanned. While this works best for smaller Azure Tables, larger tables can use the GUID strategy, which will issue requests against an Azure Table in parallel assuming the PartitionKey stores GUID values. It doesn’t mean that your PartitionKey must have GUIDs however for this strategy to work; but the backup algorithm is tuned for this condition. Other options are available as well, such as filtering which columns, entities or tables are being backed up. Check out more on the Blue Syntax website at http://www.bluesyntax.net.

  Read the article

< Previous Page | 218 219 220 221 222 223 224 225 226 227 228 229  | Next Page >