Search Results

Search found 8042 results on 322 pages for 'days'.

Page 225/322 | < Previous Page | 221 222 223 224 225 226 227 228 229 230 231 232  | Next Page >

• 1GB cached memory - Do I need more RAM?

  - by Martin

  The server runs well but I wonder if I should get more RAM. I only have a few MB of "free" memory and 1.2GB of "cached" memory: free: total used free shared buffers cached Mem: 3945 3893 51 0 28 1216 -/+ buffers/cache: 2648 1296 Swap: 3895 857 3038 I learned that cached memory is used while it's free and not. Is the cached value an indicator for the need of more RAM? cat /proc/meminfo 1 day after flushing the cache: MemTotal: 4040048 kB MemFree: 32844 kB Buffers: 18956 kB Cached: 1249092 kB SwapCached: 161576 kB Active: 3611328 kB Inactive: 189104 kB SwapTotal: 3989496 kB SwapFree: 2894200 kB Dirty: 20520 kB Writeback: 0 kB AnonPages: 2523496 kB Mapped: 217744 kB Slab: 70940 kB SReclaimable: 36756 kB SUnreclaim: 34184 kB PageTables: 99648 kB NFS_Unstable: 0 kB Bounce: 0 kB CommitLimit: 6009520 kB Committed_AS: 6401716 kB VmallocTotal: 34359738367 kB VmallocUsed: 18852 kB VmallocChunk: 34359719439 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB top: top - 17:20:10 up 112 days, 3:06, 1 user, load average: 1.01, 1.62, 1.48 Tasks: 208 total, 1 running, 207 sleeping, 0 stopped, 0 zombie Cpu(s): 0.6%us, 0.6%sy, 0.0%ni, 97.5%id, 1.3%wa, 0.0%hi, 0.1%si, 0.0%st Mem: 4040048k total, 3953108k used, 86940k free, 16348k buffers Swap: 3989496k total, 1095712k used, 2893784k free, 1235436k cached

  Read the article

• Is "DSLAM congestion" a legitimate reason for slow DSL?

  - by Jay Bazuzi

  My DSL has been extremely slow in the evenings recently. To test it, I telnet to my DSL Modem, and ping the gateway. This way I eliminate internet congestion and local network issues. In the mornings I get 30ms - 50ms pings. In the evenings, it bounces around a lot, but 10000ms pings are common. I complained to Qwest support, and they said it was a known issue on their end, their engineers were working on it, and wouldn't say anything else. A couple days later I complained again, and they sent out a technician. He tested my house wiring and found that one of them had a short. It was an unused line, so we disconnected it, and he said things looked better and left. My daytime speeds improved at this point, but evening is still bad. I complained to Qwest support again, and they said it was a problem with DSLAM congestion at their end, and that they were working on it, but no ETA. My neighbor has Qwest DSL and doesn't seem to have these problems. That seems strange. I go use her network when I absolutely must get online and mine is behaving badly. I can't tell if they're yanking my chain or not. Regardless, these speeds are crap. I'm paying for 7Mpbs but am lucky if I get 1/10th that in the evenings. My kids like to watch Netflix streaming movies, and it's just impossible after 5pm or so. Should I wait it out? Will complaining again produce any results? Should I change my subscription to a lower speed until they fix their end? Or switch to cable?

  Read the article

• What is the collaborative screen shot/diagramming application recently featured on Hacker News and p

  - by wonsungi

  A few days ago, I saw this video for a screen capture application. I'm pretty sure I followed a link from Hacker News, possibly to a Life Hacker article. The video was very short, but demonstrated how the application could be used: The application was basically a movable/resize-able view port with a button. When the button is pressed, the contents of the view port are saved to an image (basically a screen capture.) The interesting thing is what you could do after that point. One of the specific examples from the video browsed to Google maps street view, grabbed a photo of an intersection, then scribbled notes about where to meet and where the restaurant was in colored "marker." Another example shown was grabbing a house layout from from CAD tool, then scribbling notes on it. The last part of the video showed several possible uses being scrolled through the application's view port. Now, it seemed it was very easy to share these images with other people because there was some type of integration, either with their own site and/or common social websites/chat services. The application was shown running on both Windows and Mac. edit: I think there was an iPhone app, as well. Anyone know what this application is? I tried searching Google, Hacker News, and Life Hacker already. It is not Jing.

  Read the article

• Cannot log into Oracle Enterprise Manager 11g: ORA-28001

  - by Álvaro G. Vicario

  I can no longer log into Oracle Enterprise Manager 11g. I get this error message: ORA-28001: the password has expired (DBD ERROR: OCISessionBegin) I could log into the server using SQL*Plus. I warned me that the password was going to expire in 7 days (which is not the same as being already expired). Following advice from several documents, I ran these commands from SQL*Plus: ALTER USER sys IDENTIFIED BY new_password; ALTER USER system IDENTIFIED BY new_password; SQL*Plus no longer warns about passwords, but I still cannot use the Enterprise Manager. Then I followed this to remove password expiration: ALTER PROFILE default LIMIT password_life_time UNLIMITED And I've also restarted the Oracle services. In case it was using cached credentials, I've tried to connect from several browsers in several computers. No way: I still get ORA-28001 in Enterprise Manager. What am I missing? Update: Some more info SQL> select username,ACCOUNT_STATUS,EXPIRY_DATE from dba_users; USERNAME ACCOUNT_STATUS EXPIRY_D ------------------------------ -------------------------------- -------- MGMT_VIEW OPEN SYS OPEN SYSTEM OPEN

  Read the article

• High load without explanation

  - by Sebastian

  I have a very high load on my machine and don't know what is responsible or how to find out. On the machine runs a jboss appserver and mysql. Here is a top from the user at peak time: top - 16:23:01 up 101 days, 6:50, 1 user, load average: 23.42, 21.53, 24.73 Tasks: 9 total, 1 running, 8 sleeping, 0 stopped, 0 zombie Cpu(s): 17.2%us, 1.6%sy, 0.0%ni, 80.4%id, 0.1%wa, 0.1%hi, 0.7%si, 0.0%st Mem: 16440784k total, 16263720k used, 177064k free, 151916k buffers Swap: 16780872k total, 30428k used, 16750444k free, 8963648k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 27344 b 40 0 16.0g 6.5g 14m S 169 41.7 1184:09 java 6047 b 40 0 11484 1232 1228 S 0 0.0 0:00.01 mysqld_safe 6192 b 40 0 604m 182m 4696 S 0 1.1 93:30.40 mysqld 7948 b 40 0 84036 1968 1176 S 0 0.0 0:00.07 sshd 7949 b 40 0 14004 2900 1608 S 0 0.0 0:00.03 bash 7975 b 40 0 8604 1044 840 S 0 0.0 0:00.44 top The CPU usage of the java process is normal. The peaks only show up when i deployed a certain web application. Could the resulting network traffic boost the load in such way that i don't see it in top?

  Read the article

• How do I set up DNS with nic.io to point to an AWS EC2 server?

  - by Chad Johnson

  I purchased a domain one week ago via nic.io. I have elected to provide my own DNS [because they provided no other option]. I'm trying to point my .io domain at my EC2 server instance. I've allocated an elastic IP and associated it with the instance. I can SSH into the instance and access point 80 via the IP address just fine. The IP is 54.235.201.241. nic.io support said the following: "You have selected to provide your own DNS and therefore if there is an issue with the set-up of the name servers you will need to contact your DNS provider." So, I created a Hosted Zone via Route 53 in AWS. This created NS and SOA records. I then set the Primary and Secondary servers at nic.io's domain admin page to the SOA record domains. Additionally, I set the optional servers to the NS domains. I did this two days ago, and I can't access the server via the domain. I ran a DNS check here...still not sure what I need to do: http://mydnscheck.com/?domain=chadjohnson.io&ns1=&ns2=&ns3=&ns4=&ns5=&ns6=. I have no idea what I'm supposed to do. Does anyone have any ideas?

  Read the article

• Networking DOS within Windows 7 XP Mode, with a Windows XP/7 Networked Share

  - by theonlylos

  For awhile now, one of my clients has been stuck with Corel Paradox 4.0 (it used to be the biggest database system in the DOS days, until Microsoft released Access in the early 90's) so for awhile I've managed to keep it on life support on Windows XP for a few years, however since switching to Windows 7 x64, I've had to resort to using XP Mode as the sandbox to keep it up and running. While I am able to run Paradox as usual in XP Mode, I'm having a serious issue where if I try connecting the install to the network share (which is located on the Windows 7 portion of the system), Paradox keeps exiting because it says the serial number is invalid. Now, I know for a fact that this is an issue with the virtual loopback adapter and also having the VM linked to the physical ethernet adapter -- and while I have solved this issue before, most of my fixes have been bandages since after a few weeks the issue pops up again. Long story short, I wanted to ask if there is a permanent way to link a DOS program to a network share address. For example, when I try doing \tsclient\paradox (the Windows 7 Address) I keep getting an error saying I need a valid network address. I've tried mapping that folder to various drive letters such as P:\Paradox -- but for some reason that keeps failing over time. For what it's worth, Paradox uses a .SOM file to store the network settings, however it isn't editable in Notepad but rather it's controlled by a wizard in Paradox. But if that extension rings any bells, I'd welcome any insights.

  Read the article

• Any way to bring my laptop battery back to life?

  - by Josh

  Recently my laptop battery will get extremely hot (definitely hotter than it should get) when I charge it. After that I usually end up removing it once it's fully charged to let it cool down, which takes a couple hours... Question is, is my battery dead? My last battery I had that died just ended up lasting 2 - 3 minutes on battery, no weird heat issues. And is there any way to possibly fix this? Probably not but I won't be able to get a replacement anytime soon. UPDATE: A few days ago when this happened and it cooled down, assuming it was fully charged, I ran my laptop on battery, and the battery life lasted about 10 minutes and then the laptop shutdown. I then plugged it in later and charged it back up, and for a while I had a orange light blinking on my laptop - which I assumed meant the battery was dead, especially since I got 10 minutes battery life. Then today, I turned my laptop on and was surprised to see that the battery was at 20% and charging (it's been plugged in since the incident above, so it should have been fully charged when I shut it off) I let it charge up, and as usual it got pretty hot around the time it was fully charged. So I turned my laptop off and pulled the battery out to let it cool down Now the thing is, just now I tried running it on battery, and it's been going for an hour now... so maybe its not dead? (also the orange light is no longer blinking...) Thanks in advance if anyone knows whats going on, and how to fix it, if its fixable =] EDIT: Some info if it helps... my laptop is about 2 years ago, and it's an Asus K50ID. I know laptop batteries usually don't last more than a year but I'm trying to keep this one going for as long as I can.

  Read the article

• sendmail relay status

  - by Andy

  Hello all, I have a RHEL3 server with sendmail configured to relay mail to: # "Smart" relay host (may be null) DSmailrelay This relay server is an exchange server not administered by me. A few days ago its IP address was changed without my knowledge so I've updated the correct ip in /etc/hosts for the mail relay entry. Unfortunately no mail is currently going through and maillog reports: Oct 26 14:32:39 fsimag sendmail[12580]: n9Q3VxPA012580: from=root, size=3685, class=0, nrcpts=1, msgid=<~R.*.2009102614315955@*>, relay=root@localhost Oct 26 14:32:39 fsimag sendmail[12580]: n9Q3VxPA012580: to=wodwest@*.net, delay=00:00:40, mailer=esmtp, pri=33685, dsn=4.4.3, stat=queued Oct 26 14:36:09 fsimag sendmail[13670]: n9Q3ZTcf013670: from=root, size=5831, class=0, nrcpts=1, msgid=<~R.medicus.2009102614352914@*>, relay=root@localhost Oct 26 14:36:09 fsimag sendmail[13670]: n9Q3ZTcf013670: to=tsgastro@(.net, delay=00:00:40, mailer=esmtp, pri=35831, dsn=4.4.3, stat=queued Oct 26 14:36:50 fsimag sendmail[13882]: n9Q3aAxj013882: from=root, size=5830, class=0, nrcpts=1, msgid=<~C.medicus.2009102614361009@*>, relay=root@localhost Oct 26 14:36:50 fsimag sendmail[13882]: n9Q3aAxj013882: to=elmwood@*.net, delay=00:00:40, mailer=esmtp, pri=35830, dsn=4.4.3, stat=queued (With domains obscured) The mailq command shows nothing, and I've also tried connecting to this new mail server via telnet and manually sending and reports as being queued but not sent. The administrator of this machine has put it back to me saying he sees no problems, and I just want to cover everything before passing it back to him. Is there any other tests/logs/reasons for sendmail to only report it as "stat=queued" ? I've looked in previous logs and the relay is set to root@localhost in those but none were ever set to queued. Thanks for any help, Andy

  Read the article

• How to solve SocketException: Permission denied: connect

  - by luxinxian

  I recently encountered a problem that is giving me a headache and I need help ... The System consists of two subsystems, called A and B, each running on a standalone Tomcat instance and currently running on the same machine. A invokes B's service via Spring httpInvoker (i.e. over HTTP). B system also invokes the other system's services via HTTP. Symptoms: the system starts to run and appears to work normally for around 10-15 days; the system will run for a period of time after an exception: org.springframework.remoting.RemoteAccessException: Could not access HTTP invoker remote service at [http://xxx.xxx.xxx.xxx/remoting/call]; The nested exception is java. net.SocketException: **Permission denied: connect** when the exception occurs, the system continues. This happens always, not only occasionally. (It looks like some resources are exhausted, but CPU rate < 5%, memory < 15%, network < 5%). when the system call between A and B fails, the B system call over HTTP to an external service also failed, with the same exception. Restarting both Tomcat services makes the whole system work properly. So repeatedly following steps 1 - 5, I have not found the root reason. Environment: windows 2008 R2 tomcat7.0.42 x86_64 oralce-jdk-1.7.0_40 Any ideas?

  Read the article

• ownCloud WebDAV interface seems to be broken

  - by Nobleleader13245

  I've been trying to host ownCloud on my server but everytime I try to it tells me this : Your web server is not yet properly setup to allow files synchronization because the WebDAV interface seems to be broken. Please double check the installation guides. This is my setup : Windows Server 2012 R2 IIS 8.5 PHP 5.5.11 ownCloud 6.0.3 MySQL 5.6.17 I tried google the error but I can't seem to find anything usefull. Some say I should try if this works : [hostname]/remote.php/webdav/ and yes I can navigate to this folder and I can open files from there. The calendar works and I can also just upload files the web version of ownCloud the only thing that doesn't seem to work is the sync client. The sync client doesn't say anything it just doesn't connect (Screenshot : http://prntscr.com/3p2apz) This is the error log : Warning core isWebDAVWorking: NO - Reason: [CURL] Error while making request: Could not resolve host: cloud.mcsoftworks.net (error code: 6) (Sabre_DAV_Exception) 2014-06-02T19:56:00+00:00 Warning core isWebDAVWorking: NO - Reason: [CURL] Error while making request: Could not resolve host: cloud.mcsoftworks.net (error code: 6) (Sabre_DAV_Exception) 2014-06-02T19:55:47+00:00 Warning core isWebDAVWorking: NO - Reason: [CURL] Error while making request: Could not resolve host: cloud.mcsoftworks.net (error code: 6) (Sabre_DAV_Exception) 2014-06-02T19:55:34+00:00 Warning core isWebDAVWorking: NO - Reason: [CURL] Error while making request: Could not resolve host: cloud.mcsoftworks.net (error code: 6) (Sabre_DAV_Exception) 2014-06-02T19:55:34+00:00 Fatal webdav Sabre_DAV_Exception_Forbidden: Path does not exist, or escaping from the base path was detected 2014-06-02T19:54:37+00:00 Fatal webdav Sabre_DAV_Exception_Forbidden: Path does not exist, or escaping from the base path was detected 2014-06-02T19:54:36+00:00 Fatal webdav Sabre_DAV_Exception_Forbidden: Path does not exist, or escaping from the base path was detected 2014-06-02T19:54:36+00:00 Fatal webdav Sabre_DAV_Exception_Forbidden: Path does not exist, or escaping from the base path was detected 2014-06-02T19:54:36+00:00 Warning core isWebDAVWorking: NO - Reason: [CURL] Error while making request: Could not resolve host: cloud.mcsoftworks.net (error code: 6) (Sabre_DAV_Exception) 2014-06-02T19:51:24+00:00 This is my php.ini : http://pastebin.com/es3MB8Uh Does anyone have any idea on how I should get this to work? I've been trying to get this to work for about 14 days now and it starts to annoy me =P

  Read the article

• ownCloud WebDAV interface seems to be broken

  - by Nobleleader13245

  I've been trying to host ownCloud on my server but everytime I try to it tells me this : Your web server is not yet properly setup to allow files synchronization because the WebDAV interface seems to be broken. Please double check the installation guides. This is my setup : Windows Server 2012 R2 IIS 8.5 PHP 5.5.11 ownCloud 6.0.3 MySQL 5.6.17 I tried google the error but I can't seem to find anything usefull. Some say I should try if this works : https://cloud.mcsoftworks.net/remote.php/webdav/ and yes I can navigate to this folder and I can open files from there. The calendar works and I can also just upload files from here https://cloud.mcsoftworks.net/ the only thing that doesn't seem to work is the sync client. The sync client doesn't say anything it just doesn't connect (Screenshot : http://prntscr.com/3p2apz) This is the error log : Warning core isWebDAVWorking: NO - Reason: [CURL] Error while making request: Could not resolve host: cloud.mcsoftworks.net (error code: 6) (Sabre_DAV_Exception) 2014-06-02T19:56:00+00:00 Warning core isWebDAVWorking: NO - Reason: [CURL] Error while making request: Could not resolve host: cloud.mcsoftworks.net (error code: 6) (Sabre_DAV_Exception) 2014-06-02T19:55:47+00:00 Warning core isWebDAVWorking: NO - Reason: [CURL] Error while making request: Could not resolve host: cloud.mcsoftworks.net (error code: 6) (Sabre_DAV_Exception) 2014-06-02T19:55:34+00:00 Warning core isWebDAVWorking: NO - Reason: [CURL] Error while making request: Could not resolve host: cloud.mcsoftworks.net (error code: 6) (Sabre_DAV_Exception) 2014-06-02T19:55:34+00:00 Fatal webdav Sabre_DAV_Exception_Forbidden: Path does not exist, or escaping from the base path was detected 2014-06-02T19:54:37+00:00 Fatal webdav Sabre_DAV_Exception_Forbidden: Path does not exist, or escaping from the base path was detected 2014-06-02T19:54:36+00:00 Fatal webdav Sabre_DAV_Exception_Forbidden: Path does not exist, or escaping from the base path was detected 2014-06-02T19:54:36+00:00 Fatal webdav Sabre_DAV_Exception_Forbidden: Path does not exist, or escaping from the base path was detected 2014-06-02T19:54:36+00:00 Warning core isWebDAVWorking: NO - Reason: [CURL] Error while making request: Could not resolve host: cloud.mcsoftworks.net (error code: 6) (Sabre_DAV_Exception) 2014-06-02T19:51:24+00:00 This is my php.ini : http://pastebin.com/es3MB8Uh Does anyone have any idea on how I should get this to work? I've been trying to get this to work for about 14 days now and it starts to annoy me =P

  Read the article

• Recommended partitions to migrate from Windows XP to Windows 7 and Ubuntu

  - by Juanillo

  Hello, I have a system with Windows XP. My hard disk has 189 GB NTFS. I want to change the operative system to windows 7, but I want to add Ubuntu as well. As the change might take several days (because I don't have much time) I want to install one system (or Windows 7 or Ubuntu) keeping my windows XP installed in another partition so if something doesn't work in thebrand new operating system installed I can use my Windows XP installation. So I've thouht about doing something like this: Copy the data I want to keep to an external hard disk. Make partitions enough to install windows 7, keep data in another partition and another one to install Ubuntu. Copy the data I want to keep to the partition I've just created. Install Ubuntu in the partitions for Ubuntu. Check if Ubuntu works fine If it works OK install Windows 7 on the partition of Windows XP (Windows XP will be erased). Reinstall the programs in Windows 7. So my question is: How many partitions do you recommend me to have (and the size of each one and NTFS or FAT32)? The operative system I'm going to use more is Windows 7 (though I love Linux I use many programs which are windows dependant). Do you think I should do anything else / change something in the proccess to avoid any problem? I don't know if making the partitions can harm the data I have in the disk. Thanks.

  Read the article

• 32bit SQLServer with AWE NOT enabled. Buffer Cache Hit Ratio High, Disk Read Queue VERY HIGH, WHY?

  - by chenwq

  We have a "SQLServer 2005 SP3 32bit Enterprise Edition" running on a 32 bit Windows 2003 32bit Enterprise Edition 12GB RAM with AWE enabled using RAID5(5 pysical disks). We tuned AWE to enabled and restart sqlserver this afternoon after work, hope the performance will be better than old time. But there is something that we are very confused. On working days, SQLServer has a very bad performance. When we are looking for reasons, we check Windows Performance counter. Avg. Disk Read Queue Lenght > 140 Avg. Disk Write Queue Length < 1 SQL Server Buffer Cache Hit Ratio > 96% %Processor Time < 30% SQL Server Total Server Memory < 1.8G Obviously, without AWE enabled, SQL Server can use only less than 2G memory. My Question is: why "SQL Server Total server Memory" is less than 2G?I think SQL Server will use all 2G process address space. Does this counter count anything out? we known that sql server is sufferring lack of memory, but why "buffer hit ratio“ is as high as 96? Any advice is welcomed!

  Read the article

• cPanel web server redundancy advice?

  - by crgnz

  At present I operate a (reasonably low volume) web-hosting service with a Centos 5.3 server running cPanel/WHM. I would like to implement a level of redundancy such that in the event of server failure, I can restore service with a minimum of effort in less than 60 minutes. I also want to setup a secondary DNS that cPanel will replicate with. My current idea is to kill two birds with one stone by: My current server is called "www1" Purchase an identical server (HP DL360 G4) with mirrored disks. Call this server "www2" Install Centos 5.4 (or perhaps I should install 5.3 to be identical with www1) Install cPanel/WHM on this server and fully license it Setup www1 and www2 cPanel to replicate DNS with each other Setup a nightly replication script that does the following: a) rsync's the /home directory from www1 to www2 b) dumps all MySQL databases on www1 and copies them to a temp folder (with root access only) on www2 c) triggers a script to run on www2 that restores the MySQL dumps Thus each night a fully working copy of all the websites and MySQL databases is copied to www2. I do not have enough knowledge of MySQL replication to understand if it works safely and transparently with cPanel. Thus I propose the mysql dump/copy/restore due to not knowing any better! In the event that www1 dies a horrible death, I envisage that I could login to www2, change the IP addresses to those that www1 had, and presto, the websites are available again. The advantage of this idea is that it is fairly simple and "low tech" and thus does not require an expert sysadmin to setup and monitor (I am NOT an expert sysadmin) The disadvantage of this idea is that up to a full days worth of data changes would be lost. I think this would be acceptable to the sorts of customers I host at the moment. The other disadvantage would be having to pay for a full cPanel license, but I am comfortable with that cost, so for now all I want to discuss are technical considerations. Is this a sound scheme?

  Read the article

• RemoteApp .rdp embed creds?

  - by Chris_K

  Windows 2008 R2 server running Remote Desktop Services (what we used to call Terminal Services back in the olden days). This server is the entry point into a hosted application -- you could call it Software as a Service I suppose. We have 3rd party clients connecting to use it. Using RemoteApp Manager to build RemoteApp .rdp shortcuts to distribute to client workstations. These workstations are not in the same domain as the RDS server. There is no trust relationship between domains (nor will there be). There is a tightly controlled site to site VPN between workstations and the RDS server, we're quite confident we have access to the server locked down. The remoteApp being run is an ERP application with its own authentication scheme. The issue? I'm trying to avoid the need to create AD logins for every end user when connecting to the RemoteApp server. In fact, since we're doing a remoteApp and they have to authenticate to that app, I'd rather just not prompt them at all for AD creds. I certainly don't want them caught up in managing AD passwords (and periodic expirations) for accounts they only use to get to their ERP login. However, I can't figure out how to embed AD creds in a RemoteApp .rdp file. I don't really want to turn off all authentication on the RDS server at that level. Any good options? My goal is to make this as seamless as possible for the end-users. Clarifying questions are welcome.

  Read the article

• Slow parity initialization of RAID-5 array on HP Smart Array 411 controller

  - by Rob Nicholson

  On 29th October 2011, I built a RAID-5 array using 4 x 146.8GB Seagate SAS ST3146855SS drives running at 15k connected to a PowerEdge R515 with HP Smart Array P411 controller running Windows 2008 (so nothing particularly unusual). I know that parity initialisation of a RAID-5 array can take some time but it's still running after 2.5 weeks which seems a little unusual. I'd previously built another array on the same controller using 4 x 2TB SATA-2 drives and that did take a while to complete but a) I'm sure it was less than 2.5 weeks, b) that array was ~12 times bigger and c) during initialization, the percentrage slowly increased each day. At the moment, the status display for this new 2nd array simply says "Parity Initialization Status: In Progress" and it's said that since the start. It's this lack of change on the status that worries me the most - feels like it's not actually doing anything. Do you think something has gone wrong or am I being unpatient and for some reason, the status not increasing is normal? I kind of expected a much smaller array on faster drives (15k SAS versus 7.5k SATA-2) to build in a few days. This is our primary SAN running StarWind so my "have a play" options are very limited. This 2nd array is currently in use for one small virtual disk so I could shut the target machine down, move the virtual disk to another drive and try rebuilding.

  Read the article

• SSL in IIS 7 on a subdomain in a web farm

  - by justjoshingyou

  I have been having one of the most frustrating days in my entire IT career. I am trying to install an SSL certificate on a subdomain in a web farm. http://shop.mydomain.com needs to ALWAYS be forced to https://shop.mydomain.com I have a temporary cert issued from verisign on shop.mydomain.com I have installed the cert on the server. The website for shop.mydomain.com is set as a host header in IIS with the DNS entry pointed to the same IP as mydomain.com - which is our load balancer. I actually have 2 load balancers (as needed by our ISP). One redirects all traffic on port 80 out to the different servers on port 80. The other pushes out port 443 to the servers on port 443. shop.mydomain.com is to be the only site protected by SSL at this time. When I add the binding and I navigate to https://shop.mydomain.com it pops up with a warning about the cert being invalid (assumed because this is a test cert), and then it sends the user to http. So, I checked the box "Require SSL and it redirects to http://shop.mydomain.com/default.aspx and displayes an ASP.NET 404 error message. (not the IIS 404 error) I tried removing the binding on the site to port 80 as well with no luck. I am nearly ready to crawl under my desk into the fetal position. How on earth do I make this work? I can't even get it to work on one machine, let alone in the load balanced environment.

  Read the article

• Bugzilla email issue

  - by xian

  My bugzilla system keep hit the following error: There was an error sending mail from '[email protected]' to '[email protected]':Can't send data I think that is some problem with my setting and configuration. First is the urlbase I have tried setting it to bugzilla.example.com, and http://127.0.0.1:81/, and http://10.0.0.236/ (My laptop IP address, I use this laptop to set up bugzilla) but the error still persists. Actually what should I put in the urlbase field? Parameter = Email Under mail_delivery_method, i choose SMTP. Under mailfrom, I put bugzilla-daemon. smtpserver, I tried leaving it blank, or setting it to 220.181.12.12 before, but could not solve my problem For my sql, the following is the data and command I used: C:\mysql\bin>mysql --user=root -p mysql Enter password: 1234 (When I install mysql into my laptop, it ask me to key an username and password, i have key in username as 'cvuser' and password as '1234', but here never ask me to key in any username) Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 1 Server version: 5.5.15 MySQL Community Server (GPL) mysql> GRANT ALL PRIVILEGES ON bugs.* TO 'bugs'@'localhost' IDENTIFIED BY '123456'; Query OK, 0 rows affected (0.03 sec) In C:\Bugzilla\localconfig, I put the following info: # # How to access the SQL database: # $db_host = "localhost"; # where is the database? $db_port = 3306; # which port to use $db_name = "bugs"; # name of the MySQL database $db_user = "bugs"; # user to attach to the MySQL database # # Enter your database password here. It's normally advisable to specify # a password for your bugzilla database user. # If you use apostrophe (') or a backslash (\) in your password, you'll # need to escape it by preceding it with a \ character. (\') or (\\) # $db_pass = '123456'; Can someone tell me where my mistake is? I have googled for this issue for few days but still cannot find the solution.

  Read the article

• How to Change the Kerberos Default Ticket Lifetime

  - by user40497

  Our KDC servers are running either Ubuntu Dapper (2.6.15-28) or Hardy (2.6.24-19). The Kerberos software is the MIT implementation of Kerberos 5. By default, a Kerberos ticket lasts for 10 hours. However, we'd like to increase it a bit (e.g. 14 hours) to suit our needs better. I had done the following but the ticket lifetime still stays at 10 hours: 1) On all the KDC servers, set the following parameter under [realms] in /etc/krb5kdc/kdc.conf and restarted the KDC daemon: max_life = 14h 0m 0s 2) Via "kadmin", changed the "maxlife" for a test principal via "modprinc -maxlife 14hours ". "getprinc " shows that the maximum ticket life is indeed 14 hours: Maximum ticket life: 0 days 14:00:00 3) On a Kerberos client machine, set the following parameters under [libdefaults], [realms], [domain_realm], and [login] in /etc/krb5.conf (everywhere basically since nothing I tried had worked): ticket_lifetime = 13hrs default_lifetime = 13hrs With the above settings, I suppose that the ticket lifetime would be capped at 13 hours. When I do "k5start -l 14h -t ", I see that the end time for the "renew until" line is now 14 hours from the starting time: Valid starting Expires Service principal 04/13/10 16:42:05 04/14/10 02:42:05 krbtgt/@ renew until 04/14/10 06:42:03 "-l 13h" would make the end time in the "renew until" line 13 hours after the starting time. However, the ticket still expires in 10 hours (04/13 16:42:05 - 014/14 02:42:05). Am I not changing the right configuration file(s)/parameter(s), not specifying the right option when obtaining a Kerberos ticket, or something else? Any feedback is greatly appreciated! Thank you!

  Read the article

• Thunderbird alerts when expected email does not arrive

  - by user871199

  I am on Ubuntu 12.04 using Thunderbird as email client. Both are up to date in terms of updates. I have bunch of nightly jobs that do the work and send a status mail. It gets tedious if you keep getting same/similar mails every day so I ended up writing a mail filter rule which causes emails to end up in their respective folders automatically. If things are going ok, I really don't need to read emails. Failure emails are sent to different alias - if the job runs. We recently discovered that one of the job had not run for few days as someone accidentally disabled it. In order to avoid such problems in future, I would like to setup thunderbird in such a way that if I don't get email from given address within given duration, it should alert me. My dream solution is to set up frequency - some jobs do run every 4 hours. Is this possible? Can I setup Thunderbird (preferred) or other email client for reminding me when expected email does not show up. Based on comments and answer I received, here are the reasons why I would like to use Thunderbird. We are already using Thunderbird. It has calender support via plugin, so I suppose someone is already watching time to remind us about the event. May be this another type of event. Additional job is one more failure point, may complicate life if it has to monitor multiple hosts. Additional tools - same thing, one more failure point. Thunderbird can be run across all the platforms we are using - Windows and Ubuntu. It sort of becomes platform independent solution.

  Read the article

• Why is my Network Connections list empty?

  - by DealerNextDoor

  I'm sure this question has been asked before, but none of the links I have found have worked. I've been trying to find fixes for the past couple of weeks. This all started a few days after I got my router. At first, I thought it was just something that would fix it self. But as usual, it never does. I am trying to update my router's wireless card to try and fix this problem, but I need to get the card's information to update it on the HP website. And since my Network Connections list is empty, I can't get any information about it. So to get around this, I tried to go to 'Manage Wireless Networks', and when I tried to get the properties from there, I get this error: Windows has encounter an error saving the wireless profile. Specific Error: The data is invalid. So, what all can I do to try and fix this? Any help will be appreciated. EDIT: Sorry, forgot to put router info. Router Model: WNR1000v2-V2 Router Maker: NETGEAR Router Firmware Version: V1.0.0.12NA The router is up-to-date on all updates.

  Read the article

• Windows - Website unaccessible only on windows pcs in LAN

  - by DorentuZ

  For serveral days now, a website isn't accessible on a single pc in the LAN. On the other pc's, it works just fine. And it's just a single website that's not accessible as far as I know of. The website generates a timeout on every single web browser I've tried (IE8, Firefox and Chrome). However, traceroute, nmap and telnet all work just fine. I've even tried multiple user accounts and safe mode, but that didn't work either. As a side note: using a linux live cd did work and I could access the website without any problems. The hosts file is the windows default, the ip- and dns settings on the network adapter normal as well. No strange processes are running and no viruses found. According to tcpview and netstat there are connections to the domain, but every request in the browser results in a timeout.. Any idea what's happening? Update: All of the computers on the network running Windows (any version) are showing this problem now. The website is still working under linux and mac osx. So, it has to be related to some kind of windows update (although I haven't installed any on one computer in the past week, which I've set to do manual updates only)..

  Read the article

• Unable to connect to CopSSH when running Windows service, works when running sshd directly

  - by Joe Enos

  I've been using CopSSH (that uses OpenSSH and Cygwin, so I don't know which of the three is the problem) as my SSH server application at home on Windows 7 Ultimate 32 bit. I have used it for about a year with no real problems, other than it sometimes takes 2 or 3 connection attempts to get through, but it's always worked within a few attempts. A few days ago, it just stopped working. The Windows service is still running, and I've rebooted, restarted the service, etc. with no change. On the client (using Putty on Windows), I get the message "Software caused connection abort". On the server, my event viewer registers the following: fatal: Write failed: Socket operation on non-socket I finally got it working, but only by executing sshd.exe directly from the command line on the server. No special flags or options, just straight execution, and then when I connect remotely, it goes through. I do have firewall and anti-virus software which appears to be configured properly, but the fact that things work when running sshd.exe also indicates that the firewall is fine. I thought the service and executable did exactly the same thing, but apparently there's some difference. Does anyone have any ideas on where I should look for the problem? If I can't find something, I suppose I can write a Windows service or scheduled task that fires off sshd.exe directly and ensures that it stays running, but that's kind of a last resort, since it's just wrapping around something that should already work. I appreciate your help.

  Read the article

• Running Windows Update inside Windowx XP Mode

  - by Noam Gal

  I am working on a Win 7 Ultimate machine, and was using XP for some development tasks (for compatibility checks). Everything worked like a charm on the XP, including updates. Two days ago I had to switch computer (mainly a new motherboard/cpu), and I had just stuck my old HD inside the newer case. Win 7 worked like a charm - installed all the new drivers, identified everything automatically, no sweat. The trouble started when I tried running my old XP mode - it won't launch, complaining about the cpu change. I figured it's not a big deal, and I deleted the VM, and re-ran XP mode. It told me it can't find it, and offered to create a new one, just what I wanted. I had finished setting up the new XP mode VM, and it seems to work just fine. Got it to use the host network adapter, so I can surf from "inside". But I can't get Windows Update to run. Whenever I click on the "Custom" button on the WU site, after a short while, I get the [Error number: 0x80072EFD] page. I tried several solution from around the web for it (clearing some cache and restarting the wuauserv, even a microsoft fix-it run), but still nothing seems to work. Anyone here has any new tip for me? Thanks.

  Read the article

< Previous Page | 221 222 223 224 225 226 227 228 229 230 231 232  | Next Page >