Search Results

Search found 35444 results on 1418 pages for 'lock down computer'.

Page 225/1418 | < Previous Page | 221 222 223 224 225 226 227 228 229 230 231 232  | Next Page >

• Windows Server 2003 IPSec Tunnel Connected, But Not Working (Possibly NAT/RRAS Related)

  - by Kevinoid

  Configuration I have setup a "raw" IPSec tunnel between a Windows Server 2003 (SBS) machine and a Netgear FVG318 according to the instructions in Microsoft KB816514. The configuration is as follows (using the same conventions as the article): NetA | SBS2003 | FVG318 | NetB 10.0.0.0/24 | 216.x.x.x | 69.y.y.y | 10.0.254.0/24 Both the Main Mode and Quick Mode Security Associations are successfully completed and appear in the IP Security Monitor. I am also able to ping the SBS2003 server on its private address from any computer on NetB. The Problem Any traffic sent from a computer on NetA to NetB, or from SBS2003 to NetB (excluding ICMP Ping responses), is sent out on the public network interface outside the IPSec tunnel (no encryption or header authentication, as if the tunnel were not there). Pings sent from a computer on NetB to a computer on NetA successfully reach computers on NetA, but the responses are silently discarded by SBS2003 (they do not go out in the clear and do not generate any encrypted traffic). Possible Solutions Incorrect Configuration I could have mistyped something, somewhere, or KB816514 could be incorrect in some way. I have tried very hard to eliminate the first option. Have re-created the configuration several times, tried tweaking and adjusting all the settings I could without success (most prevent the SA from being established). NAT/RRAS I have seen multiple posts elsewhere suggesting that this could be due to interaction between NAT and the IPSec filters. Possibly the NetA private addresses get rewritten to 216.x.x.x before being compared with the Quick Mode IPSec filters and don't get tunneled because of the mismatch. In fact, The Cable Guy article from June 2005 "TCP/IP Packet Processing Paths" suggests that this is the case, (see step 2 and 4 of the Transit Traffic path). If this is the case, is there a way to exclude NetA-NetB traffic from NAT? Any thoughts, ideas, suggestions, and/or comments are appreciated.

  Read the article

• How to safely move where itunes saves music/iphone apps/and meta data to another internal Drive?

  - by GingerLee

  In the past, when I have moved my itunes data from one computer to another, I usually just follow these steps: Copy the contents of two folders: %USERPROFILE%\Music\iTunes %USERPROFILE%\AppData\Roaming\Apple Computer 1) Install iTunes on the new computer, start it and close it (don't let it search for music). 2) Copy all the files in the above folders from old PC to new PC. 3) Start iTunes and authorize the new computer (and deauthorize old one). 4) Before syncing, update all iphone apps to current versions on both my iphone and in itunes. 5) The Sync. The above steps always work for me, and basically Itunes on my new PC works exactly as it did on the old PC. My Question: In the hopes of bybassing the above steps in the future, I would like to just have Itunes use another internal Drive that I use for file storage (e.g. D:/) as the path for the above two directory? Then if I move to new PC again, I could just setup itunes to use the correct path. Is that possible yet with minimal implications? If so how?

  Read the article

• pfsense 2.0 traffic priority - set full priority for single host

  - by Waxhead

  I have a network with several computers all on the same network and since I have very limited bandwidth I would like to prioritize traffic almost like a CPU scheduler prioritize processes. Example: Computer A: Used for webstuff: YouTube, downloads, news, emails etc. Computer B: Transferring files over HTTP Computer C: Transferring files over ftp, rsync whatever What I would like to do is to give A up to for example 90% of the available bandwidth IF A requires it. The leftovers (10%) is divided between B and C (5% each if both is busy) If A is not utilizing all bandwidth then of course B and C should share the full bandwidth (50% each as long as both are maxing out their bandwidth). All computers are on the same network (192.168.1.0 - 192.168.1-10 for example). Appreciate if anyone could shed some light on how I should set up my network to achieve this. To be honest I actually need a step by step guide on how I should set this up. Network setup: (ADSL modem configured in bridge mode (1500kbps/300kbps)) [ADSL modem (bridge)]<-[pfsense2.0]<-[switch]<-[Computer A,B,C...etc]

  Read the article

• Dosbox USB print Windows 8.1 64Bit

  - by eCronik

  Worked fine until I've upgraded to Windows 8.1 as well as made the mail programm working (had to get a windows live ID and have to type in a password now, when starting Windows). I did set the USB printer to lpt1 on the local Windows 8 computer and another XP computer via LAN to lpt2 the same way with the same printer on the Windows 8 computer. But now it doesn't work anymore from the Win8 one (where the printer is plugged via USB). Tried already deleting lpt2: on the XP one, as well as lpt1 on the Windows 8, resetted it. Not working... :-( I tried also net use lpt1: \server\printer password "\user:Ute Berger" /persistent:yes of course with the correct server and shared printer name as well as net use \server\printer "\user:Ute Berger" password /persistent:yes . This is the name displayed as a user now. But in C:\users it is named Benutzer1. Tried this one also. Nothing worked. What could be the problem here? What's strange is that when I type "net use lpt1:" on the XP, I get another error (67 - The networkname wasn't found) than trying something I didn't set up like lpt2 (2 - The system can't find the file). Could this be a possible problem as even if deleted something is left blocking on the Windows 8 computer? Please help me - I tried for hours today but all I've got was frustration... Regards Tim

  Read the article

• linux shutdown hang with wifi cifs mounts

  - by Sirex

  Since fedora 15 (and now with 16) it seems that wireless clients take a long while to shutdown when they have network filesystems mounted at shutdown time. I've pushed out a cifs mount via puppet, and all clients have it, including those on wireless. If say a laptop is on a wired connection it shuts down just fine, but if its on the wifi at the time (and no wired connection) it'll hang at the fedora f logo. I'm not sure if its indefinite or just a really long while, but ill give it a test when i shut this machine down in a second. Needless to say its pretty annoying, so is there a way of causing the machine to shutdown even if network connectivity has been lost at unmount time, -- or an official way to reorder events so the wireless card is kept up until after the unmount happens during the shut down process (short of writing a custom script for shutdowns which is a bit of a kludge) ? It does this on multiple machines, and all started doing it when we went from fedora 14 to 15. It was such an obvious issue i'd kind of assumed someone must have reported it or there was an easy fix, but i've not discovered anything yet. Additional info: I can confirm that manually unmounting the mounts then shutting down (sudo shutdown or the xfce shutdown button) will shutdown just fine, it only hangs if the mounts are still mounted The puppet config that sets the mount looks like this (now with the _netdev entry that is indeed pushed to clients successfully, but makes no difference): file { "/mnt/share": ensure = directory,} mount { "/mnt/share": atboot = true, ensure = mounted, remounts = false, fstype = cifs, device = "//srv/share", options = "user,gid=shareusers,uid=${user},file_mode=0700,dir_mode=0700,credentials=/root/.smbcreds,_netdev", require = [ File["/mnt/share"], Group["shareusers"] ], } }

  Read the article

• Problem with connecting two different networks

  - by tanascius

  I have two networks: 192.168.13.0/24 (blue) and 192.168.15.0/24 (green). Computer A is connected to the 13-net, only. Computer B has two interfaces, one in each network. There is third computer that acts like a router and connects the 13-net to the 15-net (only in this direction). Now, I'd like to ping 192.168.15.100 from computer A to B. Unfortunately there is never a reply. But when I use a hub instead of a switch it works. In my opinion the ping packet travels through the switch to the router (which is the default route/gateway for A). The router sends the packet back to the switch to B. Probably B receives it on its 15-net interface but answers with it's 15th interface? Is this possible? The problem is, that B may have only a gateway 192.168.13.50 - but I am not really sure of it (B is a embedded system with limited configuration possibilities). Can anyone explain what happens here? Thank you!

  Read the article

• Why just splitting an Ethernet cable does not work?

  - by Sin Jeong-hun

  I thought the Ethernet is logically one-line communication bus (for argument's sake, I am excluding hubs). All machines attached in the bus hears the same signals and the machines themselves try to avoid collisions by randomly backing off. http://computer.howstuffworks.com/ethernet6.htm If so, why splitting one Ethernet line from my home router into two and connecting two computers would not work? Why do I have to add a switch to it? *What the Internet said would not work. [4 port home router] ------[one Ethernet cable]-----[simple splitter]======[two computers] *What the Internet said I should do [4 port home router] ------[one Ethernet cable]-----[switch]======[two computers] Is this because of the signal degradation (reduced electric current)? Thank you for all the answers! The reason why I did not just use the two ports of my home router is... The 4-port gigabit router is in my room and I had put a computer in another room (also my room, though). Since wired network is far more reliable and secure, I had bought a long Ethernet cable and and connected the computer to the router. Now I was thinking about adding another computer to that room. I could buy another long Ethernet cable, but then there will be two cables between the rooms. The one line already is a minor annoyance, so I thought if I could share the one line between the two computers in that room. A switch would work, but it requires power and is a little bit pricey. That is why I wondered why it would not work to simply split the physical Ethernet cable. Apparently I do not completely understand how Ethernet and a switch work. I just have some bit of knowledge I heard in my college class.

  Read the article

• Why is my Toshiba Satellite L675D laptop not connecting to my HD TV using an HDMI cord?

  - by Akasha Eyre

  I'm having a problem connecting my Toshiba Satellite L675 laptop to my Samsung HD TV. I've done it before using an HDMI cord but now, for some odd reason, it's not connecting at all. My computer screen before would go completely black for a second & then come back & (with it being attached to the TV with the HDMI cord & it being on the proper channel) it would make a sound, come on & work beautifully. Now, I try hooking it up & it doesn't do anything. No black screen, no sound. The TV screen just says there's no connection & that I need to check out the power source. I'm still checking around, trying to find out if there's a virus in my computer (since my dad & I have the same computer & he can connect his to the TV with no problems), or if I deleted something that had to do with the connection. I've tried turning my computer off & letting it sit for a while, I've tried checking out other websites & have come up with nothing.

  Read the article

• Remote Desktop Encryption

  - by Kumar

  My client is RDP 6.1 (On Windows XP SP3) and Server is Windows Server 2003. I have installed an SSL certificate on server for RDP. In the RDP settings (General tab), the Encryption method is set to SSL/TLS 1.0 and Encryption level is set to "Client Compatible". I have following questions In this case is it guaranteed that all communication is encrypted even when I remote login to the server? I mean pwd is encrypted Does RDP always use some kind of encryption even if there is no SSL certificate installed on the server? In this case I do not see security lock in the connection bar. When I set encryption level to "High" then I see security lock. I do believe that communication is both cases will be encrypted. Is it true? Please reply to my questions Thanks in advance Kumar

  Read the article

• How to recover Windows Password without reinstalling if you forgot Windows password?

  - by user38908

  Usually, we can recover Windows admin password in two traditional ways. The first is to change Windows password with another admin account; the second is to recover the previous password with the windows password reset disk that had been created before you forgot the password. Take Windows XP for example, 1 At the Windows XP login prompt when the password is entered incorrectly click the reset button in the login failed window. 2 Insert the password reset diskette into the computer and click Next. 3 If the correct diskette Windows XP will open a window prompting for the new password you wish to use. However, we offen ignore the important of security until we have been locked out of computer. Fortunately, there is still the last way that can unlock your computer without reinstalling - erase Windows password with Windows password reset CD, which can recover admin password for Windows 7/XP/Vista/NT/2000/2003.... Take Windows Password unlocker for example, followings are the steps to create the reset CD 1.Download Windows Password Unlocker from Password Unlocker Official site 2.Decompress the Windows password unlocker and note that there is an .ISO image file. Burn the image file onto an blank CD with the burner freely supported by Password Unlocker. 3.Insert the newly created CD into the locked computer and re-boot it from the CD drive. 4.After launched the CD, a window pop up with all your account names(if you have several accounts) select one of the accounts that you have forgotten its password to reset it. Just one press, this software can remove Windows password instantly.

  Read the article

• Hard drive causing BSOD

  - by JoshIrving

  I've come across a problem after building my new PC and installing a clean Windows 7. I originally planed on a RAID 1 or 0 but after further research I decided against it. So I was left with two 1TB Western Digital Black SATA 6Gb/s hard drives. My plan now was to use my second hard drive as a backup (using Windows Backup or 3rd party software). I set both hard drives to AHCI in the BIOS and installed Windows 7. I went through the lengthy process of downloading and installing each driver manually (latest versions), using the motherboard disk for a list of what I need. After a few restarts and before installing any software, I took an image backup onto DVD and the second hard drive. First witnessed the problem during the first scheduled Windows backup. The progress bar froze at about 70% (doc backup done, image backup in progress). It stayed still for 2 hours until it blue screened. Next time the backup froze, I tried shutting down. It logged me out and got stuck at the last step ("Shutting down" and blue spinner) for an hour, until I hard shutdown. I later realised this hasn't got anything to do with the backup. I ended up blue screening on almost every shut down (same place). Turns out, it's because of the second hard drive spinning down or turning off. The computer will now shutdown properly, as long as I remember to read or write to the second drive before executing shutdown. I've now set "Turn off hard disk after: Never" - No problems, so far. Do I have dodgy hard drive(s) or should I investigate the POWER_STATE_DRIVER_FAILURE BSOD - can it be a driver issue? AHCI?

  Read the article

• Can I install windows on an SSD and access data from my old windows HDD?

  - by nzifnab

  I purchased new computer components, switching my hardware from AMD and Radeon to Intel and Nvidia. I kept components from my old computer like the powersupply and two HDDs. Everything appeared to install correctly and the system booted into the BIOS just fine (after a brief snafu with the CPU fan). My goal was to use the two harddrives and just be able to turn on the computer and load up my old windows install with all the files, programs, and documents. I expected to have to call Microsoft to re-register the windows install for the new hardware (since I had to do that last time I upgraded w/ the same windows version). When the computer attempts to boot into windows it briefly flashes a bluescreen and then restarts. System recovery gives a message something like "BadDriver Failover" something something. I assume this is because it's trying to use amd drivers for an intel chipset (or something...?) and I've been as-yet unsuccessful in getting it to boot into my old windows partition. SO! I decided eff it, maybe I'll go visit my nearest Micro Center and buy a 200 GB SSD, install windows onto that, and then... be able to access just the contents of both of my other harddrives? I don't intend on running any of the programs but there were some saved files I would like to salvage from the 500 GB harddrive, The 1.5 TB harddrive only had files on it, no OS or applications so I'd also expect to still be able to access it. Is this possible? Can I install the SSD and only format/install windows onto it and still access the contents from my two transferred-over drives?

  Read the article

• Hard drive causing BSOD

  - by JoshIrving

  I've come across a problem after building my new PC and installing a clean Windows 7. I originally planed on a RAID 1 or 0 but after further research I decided against it. So I was left with two 1TB Western Digital Black SATA 6Gb/s hard drives. My plan now was to use my second hard drive as a backup (using Windows Backup or 3rd party software). I set both hard drives to AHCI in the BIOS and installed Windows 7. I went through the lengthy process of downloading and installing each driver manually (latest versions), using the motherboard disk for a list of what I need. After a few restarts and before installing any software, I took an image backup onto DVD and the second hard drive. First witnessed the problem during the first scheduled Windows backup. The progress bar froze at about 70% (doc backup done, image backup in progress). It stayed still for 2 hours until it blue screened. Next time the backup froze, I tried shutting down. It logged me out and got stuck at the last step ("Shutting down" and blue spinner) for an hour, until I hard shutdown. I later realised this hasn't got anything to do with the backup. I ended up blue screening on almost every shut down (same place). Turns out, it's because of the second hard drive spinning down or turning off. The computer will now shutdown properly, as long as I remember to read or write to the second drive before executing shutdown. I've now set "Turn off hard disk after: Never" - No problems, so far. Do I have dodgy hard drive(s) or should I investigate the POWER_STATE_DRIVER_FAILURE BSOD - can it be a driver issue? AHCI?

  Read the article

• emacs does not open a file from argument and syntax highlight does not work

  - by Jus

  In my latest ubuntu box, When I type for example emacs ~/.bashrc, Emacs will start but not open .bashrc. This is true for any file I pass in. I've used Emacs for several years, and have never experienced this problem before. I added (global-font-lock-mode 1);; to my .emacs file, and Emacs does recognize it, for example. "(C++/; Abbrev)", but it won't do syntax highlighting. If you can solve any of these problems, it will be very appreciated. The following is my machine's configuration: uname -a Linux 2.6.35-28-generic-pae #49-Ubuntu SMP Tue Mar 1 14:58:06 UTC 2011 i686 GNU/Linux ~/.emacs (global-font-lock-mode 1);;

  Read the article

• Internet compression proxy for low speed broadband?

  - by user23150

  I live in a rural location, using high-latency wireless off a local ISP's tower. My speed tests vary day to day, but I can get around 1Mb up/down. The problem is, I work with large files, uploading and downloading (HD videos, development software, etc.). It can be painful to wait sometimes. Plus I do some side contract game development, and it can be very difficult to playtest with other developers (200ms ping is a good day for me). Now, obviously it's not going to be easy to solve the latency problem without different wireless hardware. But speedwise, I am wondering if I can use some kind of compression technology on a proxy. For instance, my work computer has full access to a 26Mb down, 10Mb up connection, that is totally unused at night and the weekends. If I could run some kind of compression technology on our server, and use it as a proxy to route to my home computer, I could stand to gain some major speed. I realize that by bogging down a system with compression, I could potentially lose whatever speed gain I had. But the proxy server is a quad core xeon, and the receiving computer is a pretty decent i7 computer, so that shouldn't be a concern. I found http://toonel.net/ but it seems more geared toward very slow narrowband users, like dial-up. Plus, I would prefer to just be able to point my browser to a proxy server, rather then install software on my client machine. EDIT I thought about my question a little more, and realize I am going to need to install software on my client in order to decompress, and possible compress (for uploading). That's not a huge deal.

  Read the article

• Lost user account for Windows Vista

  - by annelie

  Hello, I'm trying to help a friend who's lost her user account in Vista. I know there's supposed to be a way you can boot the computer from the vista installation disc and create an admin account you can later login with, but her installation disc is in Australia and her laptop in London. Is there any other way to get in? Or would it be better to try and access just the harddrive? She's mainly concerned with getting all her data off it. As for how she lost the account, I'll let her explain in her words. :) My computer basically got some virus and now is up sh*t creek. it told me i had this cryptic thingy majiggy was missing and then this fake virus told me i needed to scan my computer. SO i tried to do malware thing but it kept shutting my computer down. ANYWAY...now its it will only open up with 'launch startup repair' and has got rid of my settings for logging in and wants me to be 'other user' which i have no password or username for'...so basically im stuffed. This is Windows Vista by the way. Thanks, Annelie

  Read the article

• init.d service died

  - by jerluc

  Adapting some code from a linux forum, I've added a service script to /etc/init.d on my ubuntu natty server to start/stop/restart node.js It literally was working the first day I made it, but then today, after viewing my website this morning, the server threw a 404, and upon further inspection, the node.js process was gone. So I went to start the service again, only this time, node.js didn't start at all, and ever since I haven't been able to get my service script working. Below is the entire script: #!/bin/sh # # Node Server Startup # case "$1" in start) echo -n "Starting node: " daemon node /usr/local/www/server.js echo touch /var/lock/subsys/node ;; stop) echo -n "Shutting down node: " killall node echo rm -f /var/lock/subsys/node rm -f /var/run/node.pid ;; status) status node ;; restart) $0 stop $0 start ;; reload) echo -n "Reloading node: " killall node -HUP echo ;; *) echo "Usage: $0 {start|stop|restart|reload|status}" exit 1 esac exit 0 Thanks for any help!

  Read the article

• Backup Mongodb on EC2 through EBS snapshots - timing issue

  - by DmitrySemenov

  I'm following this guidance http://docs.mongodb.org/ecosystem/tutorial/backup-and-restore-mongodb-on-amazon-ec2/ I have 4 EBS 1000 IOPS volumes assigned to instance These 4 volumes through MDADM assembled into software RAID10 array. I want to do backups through EBS Snapshots as explained in the article above Question: Mongodb says - that I need to mongo shelldb.runCommand({fsync:1,lock:1}); -- this will lock the db for writing ....run snapshot creation... mongo shell db.$cmd.sys.unlock.findOne(); -- this will unlock the db for writing so do I need to unlock the DB for writing after I issued the comand ec2-create-snapshot or after it's finished and the actual snapshot is created thanks, Dmitry

  Read the article

• is it possible to access/write database ms access 2003 .mdb at the same time?

  - by tintincute

  hi i have a problem, i have a user who created a database using ms access 2003 the problem is, if he's opening the db and made some changes, the other user can open the db but they can't work on it. but if he's exited the program, then the user can make some changes. i would like to know if its possible; that they can work at the same time when they open the database? Thanks I attached a .jpg here to see the program: www.freeimagehosting.net/image.php?ed11af4cc5.jpg additional jpg: http://www.freeimagehosting.net/image.php?3c60d8e046.jpg additional question: I tried to do the "Splitting of Database" here and after I clicked on Split I got an error: "The database engine couldn't lock the table, because it is already in use by another person or process"... what does that mean? Did I lock the table? www.freeimagehosting.net/image.php?fc52cfc486.jpg

  Read the article

• How to avoid loop limitation in a openvz container?

  - by mat.viguier

  On a openVZ containing Deb7 I need to lock the maximum size of a folder, which is used to upload on a php based web server. The directory is synced, so I have to lock the maxsize. MAXSIZE should be upgradable by adding some physical disk later ... I want to use a file as a block device for a file system. So I have done : dd if=/dev/zero of=/disk2/filesystem.dat bs=1M count=100 Then, I made the filesystem on it mkfs.ext4 filesystem.dat Then I tried to mount it : mkdir /opt/filesystem ; mount /disk2/filesystem.dat /opt/filesystem My OpenVZ (it is on a VPS) has no loop module in the kernerl. So I got Could not find any loop device as usual under OpenVz So i think I have to use FUSE, but I really do not know HOW .... Any idea on locking the size of directory under OpenVZ ?

  Read the article

• Incorrect Internal DNS Resolution

  - by user167016

  I'm having a DNS issue. Server 2008 R2. The first clue was that after being off the network for a month, I could no longer Remote Desktop into my workstation by name, it wouldn't find it. Both via VPN and internally. But if I connect using its IP, that works. Now I notice in the server's Share and Storage Management, in Manage Sessions, it's displaying the incorrect computer name for some users. So I try, for one example: Ping -a 192.168.16.81 Pinging BOBS_COMPUTER.ourdomain.local [192.168.16.81] with 32 bytes of data: - replies all successful Then I try Ping RICHARDS_COMPUTER Pinging RICHARDS_COMPUTER.ourdomain.local [192.168.16.81] with 32 bytes of data: -all replies successful In DHCP, .81 belongs to RICHARDS_COMPUTER I did try flushdns. Not sure if this is related, apologies if it's not, but when I try to connect, I also get prompted: "The identity of the remote computer cannot be verified. Do you want to connect anyway? The remote computer could not be authenticated due to problems with its security certificate. It may be unsafe to proceed.." It then lists the correct name as the name in the certificate from the remote computer, but claims that the certificate is not from a trusted authority. Any thoughts are most appreciated!

  Read the article

• Formatting a former RAID 0 drive through USB

  - by EXC

  I'll try to be as specific as possible here: I was using two Hitachi 2.5" 500 gb HDDs in my Gateway P-7805u laptop in a RAID 0 configuration. The array was causing the laptop to run extremely hot, however, so I removed them and deleted the RAID array through Intel Matrix HDD manager. I did a clean install of Windows 7 on the original 320 gb HDD that came with the laptop. I never did format the original RAID array HDDs before taking them out of the computer. Now, I am attempting to format the Hitachi 500 gb RAID array HDDs externally through a USB external enclosure. The external HDD drivers install on my clean install OS, but when I go into 'My Computer' there is no external drive available. I cannot format in CMD Prompt because my computer will not designate a drive letter to the external HDD. The drivers install and the HDD is recognized as a Hitachi external drive, but nothing seems to show up in my computer window. I need to know if there is a way to format these drives to NTFS externally.

  Read the article

• Can I insert rows next to a locked column in Excel?

  - by Tom

  If I lock cells A1:A3000, is there a way to insert rows in columns B-Z? I highlight them and I don't get the option to insert even though it is selected in the lock options. (Bottom line is that I need column A static, not to move.) Any ideas? Is it even possible? Better yet, is there any way to have formulas in column A static, as I insert rows in column B? Column A formulas change cell location when I do so.

  Read the article

• Keyboard no longer works when entering BIOS

  - by Tommy

  I am trying to boot from USB so I can install a couple different Linux distros. I can enter the BIOS, but as soon as I enter the BIOS the keyboard lights switch off (Num Lock and Caps Lock) and I cannot use the keyboard to do anything in the BIOS or even exit or restart the PC using Ctrl+Alt+Del or do anything at all with the keyboard. But as soon as I boot back into Windows, everything is fine... I've never had this problem before and some Googling hasn't helped. I've tried using a few other keyboards and simply unplugging/replugging the keyboards, but it didn't work. Is there anything I can do in Windows to maybe find out why the keyboard isn't working in the BIOS screen? In the Device Manager, all the drivers are up to date and there are no conflicts.

  Read the article

• Is there any any merit to routinely restore a linux system, even if unnecessary?

  - by field_guy

  I do fieldwork with a number of computers running ubuntu performing critical tasks doing fieldwork. The computers are similarly configured with slight variations. Since we've had some configuration issues in the past, my boss is pressing for us to take an image of the installation on each computer, and restore each computer to that image before they are to go into the field. My preferred solution would be to write a common script that checks to ensure that the configuration of the system is correct and that the system is operational. If the computer has been verified, isn't restoring it to that configuration redundant? And are there any inherent problems with doing so? My reluctance stems from the fact that our software and configuration is subject to change in the field, but these changes must be made across all the computers. That means that when a change is made, all the restoration images have to be updated as well. The differences in the configuration of each of the computers live in /etc. In the event that restoration is required, I would prefer to keep a single image containing everything that is common to all machines, and have a snapshot of each computer's /etc directory to be used for restoring the state of that particular machine. What's the better approach?

  Read the article

< Previous Page | 221 222 223 224 225 226 227 228 229 230 231 232  | Next Page >