Search Results

Search found 14205 results on 569 pages for 'remote monitor'.

Page 226/569 | < Previous Page | 222 223 224 225 226 227 228 229 230 231 232 233  | Next Page >

  • 3 screens on W500 + ATI V5700 + docking station

    - by rafek
    I've got Lenovo W500 with D-SUB and DVI ports. Most of the time I work with a docking station which has D-SUB and DVI ports, as well. I used to have laptop + 22" monitor (DVI) configuration. Now I've got laptop + 22" (DVI) + 19" (D-SUB). I was trying to configure everythin but with no success. I've got ATI V5700 in my laptop. And my ATI CCC allows me to only have one external monitor attached at the time. :( Is there any workaround to this situation? I'd like to have the configuration I've just descripted: laptop + 22" (DVI) + 19" (D-SUB).

    Read the article

  • Downloads speed starts ok but after a few seconds they go down to 10kbps?

    - by peterg
    Since yesterday any file I try to download from any host start downloading ok (at 1mbps) but after a few seconds the speed start to decrease down to 10kbps. I use a mobile modem (huawei) and I connect to a wcdma network. What could be happening? I use kaspersky, and I checked the Network Monitor and I don't see any weird process using bandwidth. What other tests can I run? Recommend me some app to monitor the traffic to see if I have some malware or see where my bandwidth goes.

    Read the article

  • Viewsonic VG2427wm detected max resolution too low

    - by Hassan
    So I have a Viewsonic VG2427wm, which supports max resolution of 1920x1080 and I had it working at this resolution from both windows and linux PCs. Now, I need to connect it to my Dell XPS17 (L702x), which has only DP mini and HDMI, so I'm trying to connect this monitor via HDMI-to-DVI adapter (doesn't work at all) and via DP-mini-to-DVI adapter. The later works, but is limiting my max resolution to 1680x1050. Using same two adapters to connect my dell monitor works fine, so I don't suspect any of the adapters to be faulty. The driver is the latest viewsonic driver (although it's been last updated 3 years back). Any ideas, how I can force it to display it's correct native resolution?

    Read the article

  • How do I tell cmake to do these two steps to use winpcap?

    - by Gtker
    Quoted from here: If your program uses Win32 specific functions of WinPcap, remember to include WPCAP among the preprocessor definitions. If your program uses the remote capture capabilities of WinPcap, add HAVE_REMOTE among the preprocessor definitions. Do not include remote-ext.h directly in your source files. Has anyone managed to use winpcap with cmake?

    Read the article

  • How to do both ways integrations across different perfoce depots?

    - by Sorin Sbarnea
    I would like to know how we are supposed to do integration between different perforce servers/depots. I'm looking for a solution that would allow us to do both-ways integrations. Currently I found some information on Using Remote Depots article where they say how to map the remote depot as read only. Is there the only solution to do mappings on both servers? - this means that I could not use a single branch spec to do both ways integrations.

    Read the article

  • How do I make YouTube videos fill up an entire screen when using dual monitors?

    - by Jephir
    I am using a dual monitor setup on Ubuntu 9.10 using the TwinView configuration in NIVIDA X Server Settings. My total resolution is 2960x1050 pixels, and my individual monitors are 1680x1050 (primary) and 1280x1024 (secondary). When going into fullscreen mode on any video on YouTube, I only see a cropped version of the video on my primary display as seen below. This does not occur on any other video sharing website - they properly make the video to fill the entire screen on my primary monitor. To my knowledge this problem only happens on YouTube.

    Read the article

  • listing network shares with python

    - by Gearoid Murphy
    Hello, if I explicitly attempt to list the contents of a shared directory on a remote host using python on a windows machine, the operation succeeds, for example, the following snippet works fine: os.listdir("\\\\remotehost\\share") However, if I attempt to list the network drives/directories available on the remote host, python fails, an example of which is shown in the following code snippet: os.listdir("\\\\remotehost") Is anyone aware of why this doesn't work?, any help/workaround is appreciated.

    Read the article

  • SQL Transactional Replication snapshot not applying

    - by dmch2
    Hi, I'm using SQL Transactional Replication with pull subscriptions to replicate databases (hosting their own distribution database) from several servers across a VPN to a central server. I've got the first 2 databases working fine but the 3rd one is causing me problems. My subscription server is SQL 2008, the source systems are all SQL 2005. The source databases are a few 100Mb in size and contain audit data so are simply growing slowly by adding new records at approx 1kb a second. As far as the replication monitor, Agent logs and event logs show everything is working fine - except that no data appears in my subscription database. The distribution agent doesn't seem to want to read the snapshot (and hence the initial state and schema) from the publisher. New transactions aren't applied although they do seem to be arriving OK as the replication monitor shows things like '5 transactions with 10 commands were delivered'. I would expect (as in previous times) to see statements about data being BCPed in the replication monitor. The snapshot is on the publisher on a shared folder. The subscriber can view the snapshot OK (\\repldata) and the alt snapshot folder is pointing at it. But the distribution agent doesn't seem to be making an attempt to do read it. I tried changing the snapshot path to something that's incorrect and didn't even get an error saying that it couldn't access it. After lots of googling etc I found that sp_MSget_repl_commands is called by the subscriber on the distribution database on the publisher. Running a profiler I can see that it's only called for one agent Id. After a reinit it's called for sequence number 0x0 as expected so I thought that would mean it's would look for the snapshot. However, looking on the publisher I see that there's data for two agents - the snapshot agent and the log reader agent (which is being queries). So I guess I need to tell the distribution agent to get the data for both. But how? and more importantly - why? It worked fine on the other two servers I've replicated. I'm not an SQL novice but this is pretty much my first go at replication so don't be afraid to accuse me of missing something obvious/stupid! I can get log files (eg from the distribution agent) if you want but they don't seem to have any errors in them - it just starts up and starts applying log reader agent changes. Cheers Dave

    Read the article

  • Best window manager for Linux for Virtual Desktop / Multimon

    - by mattcodes
    Previous used Ubuntu Gnome with Compiz but for my basic spec intel macbook (4 years old) its a little too heavyweight. So for now Im back on my macbook with os x, but now considering going back to Linux. Im looking for a window manager that has the following properties: 1) Supports virtual desktop (need 4 minimum) 2) Works well with multi monitors - can move an app with shortcut from one monitor to the other (on same virtual desktop) 3) Can remember window position (i.e. open vim on 2 monitor) - however must coerce everything back to first window when 2nd screen is unplugged 4) Keyboard shortcut friendly 5) Not too hard to install 6) Works well with minimum hardware such as integrated graphics Please suggest and share your experiences

    Read the article

  • Snow Leopard Hangs at Login Window

    - by jessecurry
    I've had an issue for the past few months, but I rarely restart so it hasn't caused too much trouble. Basically, when I start up my Mac (iMac10,1 - 3.06GHz Intel Core 2 Duo, OS X 10.6.3) everything proceeds as usual until I reach the login window. The login window displays normally, but keyboard and mouse input seem to be ignored. This condition persists for around 5 minutes at which time everything goes back to normal. While the login window is frozen my second monitor appears entirely blue, the second monitor receives a background as soon as the login window becomes responsive. If I startup while holding SHIFT the problem still occurs, but the freeze is much shorter. Looking through my logs I see no activity during the time that the login window is frozen. I've attempted to repair disk permissions, and gone through every possible maintenance option in Cocktail.

    Read the article

  • remsh rsh error redirect problem

    - by soField
    using following command on hp-ux remsh opera -l myuser crontab -l /opt1/exp_opera_crontab 2/opt/a.log and when i echo $? i get 0 because its executing crontab -l on remote machine but i dont have opt1 directory so export wont be copied to my local machine in /opt1/exp_opera_crontab i dont get any error about this when i run this remsh or rsh command is there any way to identify both of remote and local machine related errors and redirecting them into my local machine ?

    Read the article

  • T60 Screen/LCD gets black after some minutes with a highpitched sound rising and fading

    - by edelwater
    Just now my T60 screen got "black" (so no display). On my second monitor: no problems so the VGA output works. Symptom: Screen blanks / no display, but it works on the second monitor Steps to reproduce: - boot - wait (it does not matter what you do you do not have to login or anything) - (now the monitor of the laptop slowly begins to make a ssssssssHHHHHHHHHHHHHHHHHWOEOEssssssss noise of about 10 seconds) - right after the sounds ends, the monitor gets black. Sometimes it seems to be the same each time. Software: Installed no new software before/after, running ZoneAlarm and antivirus. Other: It does not feel hot in any place, there don't seem to be running processes with strange behaviour. Warranty: Out of warranty What was I doing: Typing text on a website and doing some PHP coding in a text editor. What can I do here other than buy a new laptop? Does it sound familiar to known cases? Update 1: Exactly the same problem: http://forums.lenovo.com/t5/T61-and-prior-T-series-ThinkPad/T60-Screen-Blackout/m-p/288772 and the second poster (garyj), http://forums.lenovo.com/t5/T61-and-prior-T-series-ThinkPad/Black-Screen-on-T60/m-p/235053#M48627 And here: "I have that same problem. I replaced the CCRL on mine and it works fine when the screen is not screwed in. Once the frame of the LCD screen (metal portion) touches the metal on the laptop which holds the screen the screen goes black. If the metal is touching the screen when you boot up it boots up with it being very dimmly lit. " from http://forums.lenovo.com/t5/T61-and-prior-T-series-ThinkPad/T60-screen-problems/m-p/205047#M44995 (it seems replacing the LCD display is no use, he tried it three times). Same problem: http://forums.lenovo.com/t5/T61-and-prior-T-series-ThinkPad/T60-black-screen/m-p/80604#M25914 Hmmm... not handy 3 or 4 months ago I ordered and installed a new fan. Now the LCD. Which does not seem the core issue but some electric issue so it seems replacing the LCD is not the thing to do here. If it is not the LCD that needs to be replaced (see other threads), which parts can I order to fix this? Is there any information which could lead me to identify the issue? I have read replacing the "inverter" AND the "backlightning" would that make sense? Update 2: I replaced the inverter with another inverter, but IO have the same problem. I DID notice that the inverter is the component that makes the sssssssssssssHHHHHHHHHH sound AND it becomes very hot in a few seconds. (So both the old and the test one) The problem is hmmm wat is then the thing that makes the inverter hot by (assumption) after which it shuts itself down. Is it either the input or the output? The output seems to me not, because the screen seems to function so it must be the electricity coming in. But what causes it to become so hot would it be the VGA card outputting some unusual high voltage seems unlikely? I am looking for the component to order / replace update 3: Great news. Ewendish gave me the hint to look in the BIOS. While I was in the BIOS I noticed that the screen did not switch off and there was not a high pitched sound. So I lowered some settings in the BIOS. I then noticed that with brightness turned to 0 (via FN End), it does not make a high pitched sound and does not turn off, with brightness turned up just three "stripes" it starts making the sound. So I could from now on work under lowest brightness modus or... see where the problem lies. So as stated below with either power management or display drivers / ATI Catalyst settings / Windows display settings. I'm trying to see where it lies, but I will google some first. Update 4: I wiped clean the Windows XP installation and installed Windows 7 on it. Unfortunately the problem remains: as soon as the brightness goes up the screen starts hissing. This means... back to original thought: it probably IS a hardware problem. Although ... again... if it is NOT the inverter, what is it? Could it be the backlightning component? I could try to switch that with a another T60... but this is quite tricky.

    Read the article

  • Mint 13 does nothing when laptop lid is closed

    - by ewok
    I have a laptop running Mint 13. I have it hooked up to a 30" monitor and have no use for the laptop being open, so I put it on a shelf and close it. When I do that, the monitor goes blank. The power manager does not have an option for doing nothing when the lid is closed. The options are "Blank Screen", "Suspend", and "Shutdown". Is there a way to make the laptop not go to a blank screen when the lid is closed?

    Read the article

  • Git pre-receive hook to lunch PHP CodeSniffer

    - by Ralphz
    Hey. I'd like to check code committed to my remote git repository with PHP CodeSniffer and reject it if there are any problems code standards. Does anyone have an example how to use it on git remote repository or maybe example how to use it with pre-receive hook? Thanks.

    Read the article

  • Lightweight window manager for Linux for Virtual Desktop / Multimon

    - by mattcodes
    Previous used Ubuntu Gnome with Compiz but for my basic spec intel macbook (4 years old) its a little too heavyweight. So for now Im back on my macbook with os x, but now considering going back to Linux. Im looking for a window manager that has the following properties: Supports virtual desktop (need 4 minimum) Works well with multi monitors - can move an app with shortcut from one monitor to the other (on same virtual desktop) Can remember window position (i.e. open vim on 2 monitor) - however must coerce everything back to first screen when 2nd screen is unplugged Keyboard shortcut friendly Not too hard to install Works well with minimum hardware such as integrated graphics Please suggest and share your experiences

    Read the article

  • Linux released memory

    - by user59088
    If My process allocates some big memory and then deallocates, would top or gnome-system-monitor show that my memory usage of that process decreased ? or kernel will still reserve that memory for that process ? What I see is I am deallocating memory. But I still see gnome-system-monitor displaying growing memory for my program. I don't find memory leak in my end. I want to know whether its not displaying released memory ? or there is really a memory leak at my end ?

    Read the article

  • SocketTimeout: Read timed out

    - by Lieven Cardoen
    I'm using Flex - IIS - ASP.NET to do remote calls. When I stresstest, all remote calls that take longer than 30 seconds fail. In Charles I get a message saying 'SocketTimeout: Read timed out'. Is this something that can be configured in IIS? Or could it be a problem with a setting in Charles?

    Read the article

  • Running ubuntu 10.04 without a laptop's primary display

    - by riteshmnayak
    I have an IBM thinkpad(R50e) whose display is broken. I would still like to use the laptop by connecting it to an external monitor and keyboard/mouse. This is what I did: Removed the hard disk from the broken IBM Put the hard disk in the working IBM and installed 10.04 on it. It booted fine and I installed many packages and stuff. I put the hard disk back into the broken display IBM thinking I could use it by connecting it to an external monitor that I own. Well, it turns out that while booting, the display shows up but because the display shifts from the VGA display to the primary display mid-boot, the laptop does not boot. Is there a way in which I can force the laptop to not use its primary display while booting. I looked at Randr and also grub.conf settings but nothing seemed to work. Please help!

    Read the article

  • How to make a video card use DVI output by default in text mode?

    - by Igor Zinov'yev
    I have an ASUS ENGT440/DI1GD5 video card which has three outputs: DVI, D-Sub and HDMI. I am using both D-Sub and DVI, but my main monitor is connected to the DVI output. Everything works fine except for the text mode. The card somehow uses the D-Sub output in text mode when both monitors are connected (when I disconnect the D-Sub output and leave only the primary monitor connected to the DVI output, it's being used correctly). How do I make the card use only the DVI output (or both) in text mode?

    Read the article

  • Is MySQL Replication Appropriate in this case?

    - by MJB
    I have a series of databases, each of which is basically standalone. It initially seemed like I needed a replication solution, but the more I researched it, the more it felt like replication was overkill and not useful anyway. I have not done MySQL replication before, so I have been reading up on the online docs, googling, and searching SO for relevant questions, but I can't find a scenario quite like mine. Here is a brief description of my issue: The various databases almost never have a live connection to each other. They need to be able to "sync" by copying files to a thumb drive and then moving them to the proper destination. It is OK for the data to not match exactly, but they should have the same parent-child relationships. That is, if a generated key differs between databases, no big deal. But the visible data must match. Timing is not critical. Updates can be done a week later, or even a month later, as long as they are done eventually. Updates cannot be guaranteed to be in the proper order, or in any order for that matter. They will be in order from each database; just not between databases. Rather than a set of master-slave relationships, it is more like a central database (R/W) and multiple remote databases (also R/W). I won't know how many remote databases I have until they are created. And the central DB won't know that a database exists until data arrives from it. (To me, this implies I cannot use the method of giving each its own unique identity range to guarantee uniqueness in the central database.) It appears to me that the bottom line is that I don't want "replication" so much as I want "awareness". I want the central database to know what happened in the remote databases, but there is no time requirement. I want the remote databases to be aware of the central database, but they don't need to know about each other. WTH is my question? It is this: Does this scenario sound like any of the typical replication scenarios, or does it sound like I have to roll my own? Perhaps #7 above is the only one that matters, and given that requirement, out-of-the-box replication is impossible. EDIT: I realize that this question might be more suited to ServerFault. I also searched there and found no answers to my questions. And based on the replication questions I did find both on SO and SF, it seemed that the decision was 50-50 over where to put my question. Sorry if I guessed wrong.

    Read the article

  • Client PC not booting when certain TFT plugged in - TFT or graphics card failure?

    - by Chake
    here comes something quite strange: On a client machine (DELL Vostro 420) we experienced problems when booting: when turning on the machine beeps normal but doesn't display anything and doesn't boot. After some testing I found out, that this only happens if one (of the two) monitors (Iiyama ProLite E2472HDD) is plugged in while booting. If the other monitor (TFT 2) is plugged in everything is fine. Here a small illustration, TFT 1 is the bad guy: TFT 1 | TFT 2 | failure x | x | x x | | x | x | After BIOS-Phase I can safely plug in TFT 1 and everything works just fine. The question is, what can be done to avoide this behavior: Change monitor? (Iiyama ProLite E2472HDD) Change graphics card? (GeForce 9800 GT) Other suggestions?

    Read the article

  • Passwordless SSH using cgi-perl script

    - by AV
    Hello, This is my first shot at trying out cgi-perl scripts. I have SSH keys set up between my (root user) local machine and a remote machine. I'm trying to run a command on the remote box and display the output on a webpage hosted from my local machine. The script runs fine from command line however, it throws SSH key error when called from the webpage because the user running the script is apache and not root. Is there a way to get around this issue?

    Read the article

  • 3 Monitors on a Notebook

    - by Rihan Meij
    I would like to use 3 screens on my Dell Inspiron 1720 So On the laptop built in screen have that as one, and then have 2 more screens. The catch is, that I want to play racing games with this set-up. So that my main screen is the focus area (the front window if you will) and the other 2 screens will be used for peripheral vision, on the side. The software that I use (LFS.net) does support multiple screens. However the notebook can have the main screen on, and another external screen. So I would need to split this "second" monitor output, to 2 screens, the one to the left of the main monitor, and the other one to the right. Is this possible? Is there perhaps a external card / docking station solution that could help with this? Any advice or ideas is greatly appreciated. Best Regards Rihan

    Read the article

  • Can't set correct desktop resolution on Windows 7 after playing Mirror's Edge

    - by DeadMG
    Ever since I launched Mirror's Edge, my entire system seems to think that my monitor is 1600x1200, when actually it's 1920x1080. The game would only go up to 1600x1200, Windows will only go up to 1600x1200, and even my video drivers will only go up that high. The monitor isn't even that aspect ratio. I've rebooted the system to no effect, and installed the latest graphics drivers for my Radeon 5770, unplugged it and re-plugged it, etc. My secondary screen is still working perfectly correctly. Any suggestions?

    Read the article

< Previous Page | 222 223 224 225 226 227 228 229 230 231 232 233  | Next Page >