Search Results

Search found 6301 results on 253 pages for 'dos commands'.

Page 227/253 | < Previous Page | 223 224 225 226 227 228 229 230 231 232 233 234  | Next Page >

• Trouble connecting a Ubuntu system to IPv6 tunnel over NAT

  - by John Millikin

  I'm trying to set up an IPv6 tunnel, via Hurricane Electric's tunnel-broker service. I've configured my system using their example commands: # $ipv4a = tunnel server's IPv4 IP # $ipv4b = user's IPv4 IP # $ipv6a = tunnel server's side of point-to-point /64 allocation # $ipv6b = user's side of point-to-point /64 allocation ip tunnel add he-ipv6 mode sit remote $ipv4a local $ipv4b ttl 255 ip link set he-ipv6 up ip addr add $ipv6b dev he-ipv6 ip route add ::/0 dev he-ipv6 And have configured my desktop to be in my NAT router's DMZ. The router is running Tomato firmware. But I can't ping any IPv6 services: $ ping6 -I he-ipv6 '2001:470:1f04:454::1' PING 2001:470:1f04:454::1(2001:470:1f04:454::1) from 2001:470:1f04:454::2 he-ipv6: 56 data bytes From 2001:470:1f04:454::2 icmp_seq=1 Destination unreachable: Address unreachable From 2001:470:1f04:454::2 icmp_seq=2 Destination unreachable: Address unreachable I can ping my local address: $ ping6 -I he-ipv6 '2001:470:1f04:454::2' PING 2001:470:1f04:454::2(2001:470:1f04:454::2) from 2001:470:1f04:454::2 he-ipv6: 56 data bytes 64 bytes from 2001:470:1f04:454::2: icmp_seq=1 ttl=64 time=0.037 ms 64 bytes from 2001:470:1f04:454::2: icmp_seq=2 ttl=64 time=0.039 ms I don't know much about routing, but results I found online suggested the output of ip -6 route and ip addr could be useful: $ ip -6 route 2001:470:1f04:454::/64 via :: dev he-ipv6 proto kernel metric 256 mtu 1480 advmss 1420 hoplimit 4294967295 fe80::/64 dev virbr0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 via :: dev he-ipv6 proto kernel metric 256 mtu 1480 advmss 1420 hoplimit 4294967295 default dev he-ipv6 metric 1024 mtu 1480 advmss 1420 hoplimit 4294967295 $ ip addr 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 100 link/ether 00:1c:c0:a1:98:b2 brd ff:ff:ff:ff:ff:ff inet 192.168.1.10/24 brd 192.168.1.255 scope global eth1 inet6 fe80::21c:c0ff:fea1:98b2/64 scope link valid_lft forever preferred_lft forever 3: virbr0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN link/ether 36:4c:33:ab:0d:c6 brd ff:ff:ff:ff:ff:ff inet 192.168.122.1/24 brd 192.168.122.255 scope global virbr0 inet6 fe80::344c:33ff:feab:dc6/64 scope link valid_lft forever preferred_lft forever 4: vboxnet0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000 link/ether 00:76:62:6e:65:74 brd ff:ff:ff:ff:ff:ff 5: pan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether 7e:29:5e:7c:ba:93 brd ff:ff:ff:ff:ff:ff 6: sit0: <NOARP> mtu 1480 qdisc noop state DOWN link/sit 0.0.0.0 brd 0.0.0.0 7: he-ipv6@NONE: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1480 qdisc noqueue state UNKNOWN link/sit 24.130.225.239 peer 72.52.104.74 inet6 2001:470:1f04:454::2/64 scope global valid_lft forever preferred_lft forever inet6 fe80::1882:e1ef/128 scope link valid_lft forever preferred_lft forever

  Read the article

• Squid 2.7.STABLE3-4.1 as a transparent proxy on Ubuntu Server 9.04

  - by E3 Group

  Can't get this to work at all! I'm trying to get this linux box to act as a transparent proxy and, with the help of DHCP, force everyone on the network to gate into the proxy. I have two ethernet connections, both to the same switch. And I'm trying to get 192.168.1.234 to become the default gateway. The actual WAN connection is to a gateway 192.168.1.1. eth0 is 192.168.1.234 eth1 is 192.168.1.2 Effectively I'm trying to make eth0 a LAN only interface and eth1 a WAN interface. I've oi should set the gateway for eth1 to point to 192.168.1.234 my squid.conf file has the following directives added at the bottom: nly set eth0 to have a gateway address in /etc/network/interfaces I'm not sure whether http_port 3128 transparent acl lan src 192.168.1.0/24 acl lh src 127.0.0.1/255.255.255.0 http_access allow lan http_access allow lh i've added the following routing commands: iptables -t nat -A PREROUTING -i eth0 -p tcp -m tcp --dport 80 -j DNAT --to-destination 192.168.1.2:3128 iptables -t nat -A PREROUTING -i eth1 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128 I set a computer with TCP settings 192.168.1.234 as the gateway and opened up google.com, but it comes up with a request error. Any ideas why this isn't working? :( Been searching continuously for a solution to no avail. ----------------------------- EDIT ------------------------------- Managed to get it to route properly to the squid, here's the error I get in the browser: ERROR The requested URL could not be retrieved While trying to process the request: GET / HTTP/1.1 Host: www.google.com User-Agent: Mozilla/5.0 (Windows; U; Windows NT 5.1; en-GB; rv:1.9.1.2) Gecko/20090729 Firefox/3.5.2 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-gb,en;q=0.5 Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 300 Connection: keep-alive Cache-Control: max-age=0 The following error was encountered: * Invalid Request Some aspect of the HTTP Request is invalid. Possible problems: * Missing or unknown request method * Missing URL * Missing HTTP Identifier (HTTP/1.0) * Request is too large * Content-Length missing for POST or PUT requests * Illegal character in hostname; underscores are not allowed Your cache administrator is webmaster. Generated Mon, 26 Oct 2009 03:41:15 GMT by mjolnir.lloydharrington.local (squid/2.7.STABLE3)

  Read the article

• error while installing the libmemcached

  - by Ahmet vardar

  I get this while installing libmemcached root@server [/libmemcached]# make make all-am make[1]: Entering directory `/libmemcached' if /bin/sh ./libtool --tag=CXX --mode=compile g++ -DHAVE_CONFIG_H -I. -I. -I. -I. -I. -ggdb -DBUILDING_HASHKIT -MT libhashkit/libhashkit_libhashkit_la-aes.lo -MD -MP -MF "libhashkit/.deps/libhashkit_libhashkit_la-aes.Tpo" -c -o libhashkit/libhashkit_libhashkit_la-aes.lo `test -f 'libhashkit/aes.cc' || echo './'`libhashkit/aes.cc; \ then mv -f "libhashkit/.deps/libhashkit_libhashkit_la-aes.Tpo" "libhashkit/.deps/libhashkit_libhashkit_la-aes.Plo"; else rm -f "libhashkit/.deps/libhashkit_libhashkit_la-aes.Tpo"; exit 1; fi ./libtool: line 866: X--tag=CXX: command not found ./libtool: line 899: libtool: ignoring unknown tag : command not found ./libtool: line 866: X--mode=compile: command not found ./libtool: line 1032: *** Warning: inferring the mode of operation is deprecated.: command not found ./libtool: line 1033: *** Future versions of Libtool will require --mode=MODE be specified.: command not found ./libtool: line 1176: Xg++: command not found ./libtool: line 1176: X-DHAVE_CONFIG_H: command not found ./libtool: line 1176: X-I.: command not found ./libtool: line 1176: X-I.: command not found ./libtool: line 1176: X-I.: command not found ./libtool: line 1176: X-I.: command not found ./libtool: line 1176: X-I.: command not found ./libtool: line 1176: X-ggdb: command not found ./libtool: line 1176: X-DBUILDING_HASHKIT: command not found ./libtool: line 1176: X-MT: command not found ./libtool: line 1176: Xlibhashkit/libhashkit_libhashkit_la-aes.lo: No such file or directory ./libtool: line 1176: X-MD: command not found ./libtool: line 1176: X-MP: command not found ./libtool: line 1176: X-MF: command not found ./libtool: line 1176: Xlibhashkit/.deps/libhashkit_libhashkit_la-aes.Tpo: No such file or directory ./libtool: line 1176: X-c: command not found ./libtool: line 1228: Xlibhashkit/libhashkit_libhashkit_la-aes.lo: No such file or directory ./libtool: line 1233: libtool: compile: cannot determine name of library object from `': command not found make[1]: *** [libhashkit/libhashkit_libhashkit_la-aes.lo] Error 1 make[1]: Leaving directory `/libmemcached' make: *** [all] Error 2 OUTPUT OF ./configure checking build system type... x86_64-unknown-linux-gnu checking host system type... x86_64-unknown-linux-gnu checking target system type... x86_64-unknown-linux-gnu checking for a BSD-compatible install... /usr/bin/install -c checking whether build environment is sane... yes checking for gawk... gawk checking whether make sets $(MAKE)... yes checking for style of include used by make... GNU checking for gcc... gcc checking whether the C compiler works... yes checking for C compiler default output file name... a.out checking for suffix of executables... checking whether we are cross compiling... no checking for suffix of object files... o checking whether we are using the GNU C compiler... yes checking whether gcc accepts -g... yes checking for gcc option to accept ISO C89... none needed checking dependency style of gcc... gcc3 checking dependency style of gcc... (cached) gcc3 checking how to run the C preprocessor... gcc -E checking for grep that handles long lines and -e... /bin/grep checking for egrep... /bin/grep -E checking for ANSI C header files... yes checking for sys/types.h... yes checking for sys/stat.h... yes checking for stdlib.h... yes checking for string.h... yes checking for memory.h... yes checking for strings.h... yes checking for inttypes.h... yes checking for stdint.h... yes checking for unistd.h... yes checking minix/config.h usability... no checking minix/config.h presence... no checking for minix/config.h... no checking whether it is safe to define __EXTENSIONS__... yes checking for isainfo... no checking for g++... g++ checking whether we are using the GNU C++ compiler... yes checking whether g++ accepts -g... yes checking dependency style of g++... gcc3 checking dependency style of g++... (cached) gcc3 checking whether gcc and cc understand -c and -o together... yes checking how to create a ustar tar archive... gnutar checking whether __SUNPRO_C is declared... no checking whether __ICC is declared... no checking "C Compiler version--yes"... "gcc (GCC) 4.1.2 20080704 (Red Hat 4.1.2-52)" checking "C++ Compiler version"... "g++ (GCC) 4.1.2 20080704 (Red Hat 4.1.2-52)" checking whether time.h and sys/time.h may both be included... yes checking whether struct tm is in sys/time.h or time.h... time.h checking for size_t... yes checking for special C compiler options needed for large files... no checking for _FILE_OFFSET_BITS value needed for large files... no checking for library containing clock_gettime... -lrt checking sys/socket.h usability... yes checking sys/socket.h presence... yes checking for sys/socket.h... yes checking size of off_t... 8 checking size of size_t... 8 checking size of long long... 8 checking if time_t is unsigned... no checking for setsockopt... yes checking for bind... yes checking whether the compiler provides atomic builtins... yes checking assert.h usability... yes checking assert.h presence... yes checking for assert.h... yes checking whether to enable assertions... yes checking whether it is safe to use -fdiagnostics-show-option... yes checking whether it is safe to use -floop-parallelize-all... no checking whether it is safe to use -Wextra... yes checking whether it is safe to use -Wformat... yes checking whether it is safe to use -Wconversion... no checking whether it is safe to use -Wmissing-declarations from C++... no checking whether it is safe to use -Wframe-larger-than... no checking whether it is safe to use -Wlogical-op... no checking whether it is safe to use -Wredundant-decls from C++... yes checking whether it is safe to use -Wattributes from C++... no checking whether it is safe to use -Wno-attributes... no checking for perl... perl checking for dpkg-gensymbols... no checking for lcov... no checking for genhtml... no checking for sphinx-build... no checking for working -pipe... yes checking for bison... bison checking for flex... flex checking how to print strings... printf checking for a sed that does not truncate output... /bin/sed checking for fgrep... /bin/grep -F checking for ld used by gcc... /usr/bin/ld checking if the linker (/usr/bin/ld) is GNU ld... yes checking for BSD- or MS-compatible name lister (nm)... /usr/bin/nm -B checking the name lister (/usr/bin/nm -B) interface... BSD nm checking whether ln -s works... yes checking the maximum length of command line arguments... 98304 checking whether the shell understands some XSI constructs... yes checking whether the shell understands "+="... yes checking how to convert x86_64-unknown-linux-gnu file names to x86_64-unknown-linux-gnu format... func_convert_file_noop checking how to convert x86_64-unknown-linux-gnu file names to toolchain format... func_convert_file_noop checking for /usr/bin/ld option to reload object files... -r checking for objdump... objdump checking how to recognize dependent libraries... pass_all checking for dlltool... no checking how to associate runtime and link libraries... printf %s\n checking for ar... ar checking for archiver @FILE support... @ checking for strip... strip checking for ranlib... ranlib checking command to parse /usr/bin/nm -B output from gcc object... ok checking for sysroot... no checking for mt... no checking if : is a manifest tool... no checking for dlfcn.h... yes checking for objdir... .libs checking if gcc supports -fno-rtti -fno-exceptions... no checking for gcc option to produce PIC... -fPIC -DPIC checking if gcc PIC flag -fPIC -DPIC works... yes checking if gcc static flag -static works... yes checking if gcc supports -c -o file.o... yes checking if gcc supports -c -o file.o... (cached) yes checking whether the gcc linker (/usr/bin/ld -m elf_x86_64) supports shared libraries... yes checking whether -lc should be explicitly linked in... no checking dynamic linker characteristics... GNU/Linux ld.so checking how to hardcode library paths into programs... immediate checking whether stripping libraries is possible... yes checking if libtool supports shared libraries... yes checking whether to build shared libraries... yes checking whether to build static libraries... yes checking how to run the C++ preprocessor... g++ -E checking for ld used by g++... /usr/bin/ld -m elf_x86_64 checking if the linker (/usr/bin/ld -m elf_x86_64) is GNU ld... yes checking whether the g++ linker (/usr/bin/ld -m elf_x86_64) supports shared libraries... yes checking for g++ option to produce PIC... -fPIC -DPIC checking if g++ PIC flag -fPIC -DPIC works... yes checking if g++ static flag -static works... yes checking if g++ supports -c -o file.o... yes checking if g++ supports -c -o file.o... (cached) yes checking whether the g++ linker (/usr/bin/ld -m elf_x86_64) supports shared libraries... yes checking dynamic linker characteristics... (cached) GNU/Linux ld.so checking how to hardcode library paths into programs... immediate checking whether the -Werror option is usable... yes checking for simple visibility declarations... yes checking for ISO C++ 98 include files... checking whether memcached executable path has been provided... no checking for memcached... /usr/local/bin/memcached checking whether memcached_sasl executable path has been provided... no checking for memcached_sasl... no checking whether gearmand executable path has been provided... no checking for gearmand... no checking libgearman/gearmand.h usability... no checking libgearman/gearmand.h presence... no checking for libgearman/gearmand.h... no checking for library containing getopt_long... none required checking for library containing gethostbyname... none required checking for the pthreads library -lpthreads... no checking whether pthreads work without any flags... yes checking for joinable pthread attribute... PTHREAD_CREATE_JOINABLE checking if more special flags are required for pthreads... no checking for PTHREAD_PRIO_INHERIT... yes checking the location of cstdint... configure: WARNING: Could not find a cstdint header. <stdint.h> checking the location of cinttypes... configure: WARNING: Could not find a cinttypes header. <inttypes.h> checking whether byte ordering is bigendian... no checking for htonll... no checking for working SO_SNDTIMEO... yes checking for working SO_RCVTIMEO... yes checking for supported struct padding... yes checking for alarm... yes checking for dup2... yes checking for getline... yes checking for gettimeofday... yes checking for memchr... yes checking for memmove... yes checking for memset... yes checking for pipe2... no checking for select... yes checking for setenv... yes checking for socket... yes checking for sqrt... yes checking for strcasecmp... yes checking for strchr... yes checking for strdup... yes checking for strerror... yes checking for strtol... yes checking for strtoul... yes checking for strtoull... yes checking arpa/inet.h usability... yes checking arpa/inet.h presence... yes checking for arpa/inet.h... yes checking fcntl.h usability... yes checking fcntl.h presence... yes checking for fcntl.h... yes checking libintl.h usability... yes checking libintl.h presence... yes checking for libintl.h... yes checking limits.h usability... yes checking limits.h presence... yes checking for limits.h... yes checking malloc.h usability... yes checking malloc.h presence... yes checking for malloc.h... yes checking netdb.h usability... yes checking netdb.h presence... yes checking for netdb.h... yes checking netinet/in.h usability... yes checking netinet/in.h presence... yes checking for netinet/in.h... yes checking stddef.h usability... yes checking stddef.h presence... yes checking for stddef.h... yes checking sys/time.h usability... yes checking sys/time.h presence... yes checking for sys/time.h... yes checking execinfo.h usability... yes checking execinfo.h presence... yes checking for execinfo.h... yes checking cxxabi.h usability... yes checking cxxabi.h presence... yes checking for cxxabi.h... yes checking sys/sysctl.h usability... yes checking sys/sysctl.h presence... yes checking for sys/sysctl.h... yes checking umem.h usability... no checking umem.h presence... no checking for umem.h... no checking for C++ compiler vendor... gnu checking for working alloca.h... yes checking for alloca... yes checking for error_at_line... yes checking for pid_t... yes checking vfork.h usability... no checking vfork.h presence... no checking for vfork.h... no checking for fork... yes checking for vfork... yes checking for working fork... yes checking for working vfork... (cached) yes checking for stdlib.h... (cached) yes checking for GNU libc compatible malloc... yes checking for stdlib.h... (cached) yes checking for GNU libc compatible realloc... yes checking whether strerror_r is declared... yes checking for strerror_r... yes checking whether strerror_r returns char *... yes checking for stdbool.h that conforms to C99... yes checking for _Bool... no checking for int16_t... yes checking for int32_t... yes checking for int64_t... yes checking for int8_t... yes checking for off_t... yes checking for pid_t... (cached) yes checking for ssize_t... yes checking for uint16_t... yes checking for uint32_t... yes checking for uint64_t... yes checking for uint8_t... yes checking whether byte ordering is bigendian... (cached) no checking for an ANSI C-conforming const... yes checking for inline... inline checking for working volatile... yes checking for C/C++ restrict keyword... __restrict checking whether the compiler supports GCC C++ ABI name demangling... yes checking sasl/sasl.h usability... no checking sasl/sasl.h presence... no checking for sasl/sasl.h... no checking uuid/uuid.h usability... yes checking uuid/uuid.h presence... yes checking for uuid/uuid.h... yes checking for main in -luuid... yes checking for clock_gettime in -lrt... yes checking for floor in -lm... yes checking for sigignore... yes checking atomic.h usability... no checking atomic.h presence... no checking for atomic.h... no checking for setppriv... no checking for winsock2.h... no checking for poll.h... yes checking for sys/wait.h... yes checking for fnmatch.h... yes checking for MSG_NOSIGNAL... yes checking for MSG_DONTWAIT... yes checking for MSG_MORE... yes checking event.h usability... yes checking event.h presence... yes checking for event.h... yes checking for main in -levent... yes checking for endianness... little configure: creating ./config.status config.status: creating Makefile config.status: creating docs/conf.py config.status: creating libhashkit-1.0/configure.h config.status: creating libmemcached-1.0/configure.h config.status: creating libmemcached-1.2/configure.h config.status: creating libmemcached-2.0/configure.h config.status: creating support/libmemcached.pc config.status: creating support/libmemcached.spec config.status: creating support/libmemcached-fc.spec config.status: creating libtest/version.h config.status: creating config.h config.status: config.h is unchanged config.status: executing depfiles commands config.status: executing libtool commands --- Configuration summary for libmemcached version 1.0.6 * Installation prefix: /usr/local * System type: unknown-linux-gnu * Host CPU: x86_64 * C Compiler: gcc (GCC) 4.1.2 20080704 (Red Hat 4.1.2-52) * Assertions enabled: yes * Debug enabled: no * Warnings as failure: no * SASL support: --- anyone knows how to solve this ?

  Read the article

• Uninstalling MySQL for MariaDB Replacement on cPanel

  - by ImmortalFirefly

  Well the first part of my day was spent researching how to remove MySQL to install MariaDB and the second part of my day was spent trying to reinstall MySQL cause something was messed up. So now I come to the masses for some help. I have a box with cPanel/WHM on it. CentOS 5.6 64 bit. I have upgraded (through WHM) MySQL to 5.5.24 and that was successful. After some research, the options I found were an intimidating Linux command with pipes greps and dashes, and another command yum remove mysql I tried that out and it appeared to remove mysql.....ish. I tried installing MariaDB from this instructions page and it started to do it's thing and then came the zillions of errors (here's a small sample): Transaction Check Error: file /etc/init.d/mysql from install of MariaDB-server-5.5.25-1.i386 conflicts with file from package MySQL-server-5.5.24-1.cp.1132.x86_64 file /usr/bin/mysql_convert_table_format from install of MariaDB-server-5.5.25-1.i386 conflicts with file from package MySQL-server-5.5.24-1.cp.1132.x86_64 file /usr/bin/mysql_install_db from install of MariaDB-server-5.5.25-1.i386 conflicts with file from package MySQL-server-5.5.24-1.cp.1132.x86_64 file /usr/bin/mysql_secure_installation from install of MariaDB-server-5.5.25-1.i386 conflicts with file from package MySQL-server-5.5.24-1.cp.1132.x86_64 file /usr/bin/mysqlbug from install of MariaDB-server-5.5.25-1.i386 conflicts with file from package MySQL-server-5.5.24-1.cp.1132.x86_64 file /usr/bin/mysqld_multi from install of MariaDB-server-5.5.25-1.i386 conflicts with file from package MySQL-server-5.5.24-1.cp.1132.x86_64 file /usr/bin/mysqld_safe from install of MariaDB-server-5.5.25-1.i386 conflicts with file from package MySQL-server-5.5.24-1.cp.1132.x86_64 file /usr/bin/mysqldumpslow from install of MariaDB-server-5.5.25-1.i386 conflicts with file from package MySQL-server-5.5.24-1.cp.1132.x86_64 file /usr/bin/mysqlhotcopy from install of MariaDB-server-5.5.25-1.i386 conflicts with file from package MySQL-server-5.5.24-1.cp.1132.x86_64 file /usr/share/man/man1/innochecksum.1.gz from install of MariaDB-server-5.5.25-1.i386 conflicts with file from package MySQL-server-5.5.24-1.cp.1132.x86_64 file /usr/share/man/man1/my_print_defaults.1.gz from install of MariaDB-server-5.5.25-1.i386 conflicts with file from package MySQL-server-5.5.24-1.cp.1132.x86_64 file /usr/share/man/man1/myisam_ftdump.1.gz from install of MariaDB-server-5.5.25-1.i386 conflicts with file from package MySQL-server-5.5.24-1.cp.1132.x86_64 file /usr/share/man/man1/myisamchk.1.gz from install of MariaDB-server-5.5.25-1.i386 conflicts with file from package MySQL-server-5.5.24-1.cp.1132.x86_64 file /usr/share/man/man1/myisamlog.1.gz from install of MariaDB-server-5.5.25-1.i386 conflicts with file from package MySQL-server-5.5.24-1.cp.1132.x86_64 So it appeared that MySQL wasn't removed correctly. I've read from different tutorials given on different sites that to install MariaDB, you had to uninstall/remove MySQL and there weren't any commands given on how to do this. Does anyone know how to "safely" remove MySQL on a WHM/cPanel server so that I can install MariaDB? Here's my repo file in case anyone needs to know... # MariaDB repository list - created 2012-07-10 17:09 UTC # http://downloads.mariadb.org/mariadb/repositories/ [mariadb] name = MariaDB baseurl = http://yum.mariadb.org/5.5/centos5-x86 gpgcheck=1

  Read the article

• GRUB 2 freezing at OS selection screen, what could be the cause?

  - by Michael Kjörling

  Mains power is somewhat unreliable where I live, so every now and then, the computer gets rebooted when the PSU can't maintain proper voltage during a brown-out or momentary black-out. It's happened a few times recently that when power is restored, the BIOS POST completes successfully, GRUB starts to load and then freezes. I've seen this at the Welcome to GRUB! message, but it seems to happen more often just past the switch to the graphical OS list. At this point, the computer will not respond to anything (arrow keys, control commands, Ctrl+Alt+Del, ...) - it simply sits there displaying this image, seemingly doing nothing more. At that point, turning the computer off using the power button and letting it sit for a while (cooling down?) has allowed it to boot successfully. Turning the computer off and immediately back on seems to give the same result (successful POST then freeze in GRUB). This behavior began recently, although does not seem to be directly correlated with my hard disk woes (although it may be relevant that GRUB resides on that physical disk, I don't know). Once the computer has booted, it runs without a hitch. I know that a "proper" solution would be to invest in a UPS, but what might be causing behavior like this? I was thinking in terms of perhaps the CPU shutting down as a thermal control measure, but if that was the cause then wouldn't I see similar freezes during use (which I do not)? What else could cause freezes apparently closely but not perfectly related to the BIOS handover from POST to OS bootloader? The BIOS settings are to reset to previous power status after a power loss. Since the PC in question is almost always turned on, this means restore to full power status. I have no expansion cards installed that make any BIOS extensions known by screen output during the boot process, at least, but I do have a few expansion cards installed. Haven't made any changes in that regard in a long time, now. I haven't touched GRUB itself for a long time, whether configuration or binaries, so I don't think that's the problem. Also, it doesn't really make sense that a bug in GRUB would manifest itself only once in a blue moon but significantly more often after a power failure.

  Read the article

• How to properly add .NET assemblies to Powershell session?

  - by amandion

  I have a .NET assembly (a dll) which is an API to backup software we use here. It contains some properties and methods I would like to take advantage of in my Powershell script(s). However, I am running into a lot of issues with first loading the assembly, then using any of the types once the assembly is loaded. The complete file path is: C:\rnd\CloudBerry.Backup.API.dll In Powershell I use: $dllpath = "C:\rnd\CloudBerry.Backup.API.dll" Add-Type -Path $dllpath I get the error below: Add-Type : Unable to load one or more of the requested types. Retrieve the LoaderExceptions property for more information. At line:1 char:9 + Add-Type <<<< -Path $dllpath + CategoryInfo : NotSpecified: (:) [Add-Type], ReflectionTypeLoadException + FullyQualifiedErrorId : System.Reflection.ReflectionTypeLoadException,Microsoft.PowerShell.Commands.AddTypeComma ndAdd-Type : Unable to load one or more of the requested types. Retrieve the LoaderExceptions property for more information. Using the same cmdlet on another .NET assembly, DotNetZip, which has examples of using the same functionality on the site also does not work for me. I eventually find that I am seemingly able to load the assembly using reflection: [System.Reflection.Assembly]::LoadFrom($dllpath) Although I don't understand the difference between the methods Load, LoadFrom, or LoadFile that last method seems to work. However, I still seem to be unable to create instances or use objects. Each time I try, I get errors that describe that Powershell is unable to find any of the public types. I know the classes are there: $asm = [System.Reflection.Assembly]::LoadFrom($dllpath) $cbbtypes = $asm.GetExportedTypes() $cbbtypes | Get-Member -Static ---- start of excerpt ---- TypeName: CloudBerryLab.Backup.API.BackupProvider Name MemberType Definition ---- ---------- ---------- PlanChanged Event System.EventHandler`1[CloudBerryLab.Backup.API.Utils.ChangedEventArgs] PlanChanged(Sy... PlanRemoved Event System.EventHandler`1[CloudBerryLab.Backup.API.Utils.PlanRemoveEventArgs] PlanRemoved... CalculateFolderSize Method static long CalculateFolderSize() Equals Method static bool Equals(System.Object objA, System.Object objB) GetAccounts Method static CloudBerryLab.Backup.API.Account[], CloudBerry.Backup.API, Version=1.0.0.1, Cu... GetBackupPlans Method static CloudBerryLab.Backup.API.BackupPlan[], CloudBerry.Backup.API, Version=1.0.0.1,... ReferenceEquals Method static bool ReferenceEquals(System.Object objA, System.Object objB) SetProfilePath Method static System.Void SetProfilePath(string profilePath) ----end of excerpt---- Trying to use static methods fail, I don't know why!!! [CloudBerryLab.Backup.API.BackupProvider]::GetAccounts() Unable to find type [CloudBerryLab.Backup.API.BackupProvider]: make sure that the assembly containing this type is load ed. At line:1 char:42 + [CloudBerryLab.Backup.API.BackupProvider] <<<< ::GetAccounts() + CategoryInfo : InvalidOperation: (CloudBerryLab.Backup.API.BackupProvider:String) [], RuntimeException + FullyQualifiedErrorId : TypeNotFound Any guidance appreciated!!

  Read the article

• autocomplete not working on one sever, works on others

  - by dogmatic69

  I have Ubuntu 10.10 x64 and x86 running on various servers and auto complete works on all of them bar one. The issue: apt-<tab> would show a list of options but sudo apt-<tab> would not. After fiddling with it for a few hours i've found that /etc/bash_autocomplete did not exist. on the broken server. Copying the one from a working one it now works. but still not properly. sudo apt-get ins<tab> does not show do anything. listing the files in /etc/bash_autocomplete.d/ on the working server has about 50 files, and the broken one only two or three. i dont think that i can just copy these files though as it might show commands for things that are not even installed. TL;DR autocomplete broken, how can i fix it. Seems like its disabled somewhere, why is this EDIT: Ok, it was not ever installed... $ sudo apt-get install bash-completion Reading package lists... Done Building dependency tree Reading state information... Done The following NEW packages will be installed bash-completion 0 upgraded, 1 newly installed, 0 to remove and 3 not upgraded. Need to get 140kB of archives. After this operation, 1,061kB of additional disk space will be used. Get:1 http://archive.ubuntu.com/ubuntu/ maverick-updates/main bash-completion all 1:1.2-2ubuntu1.1 [140kB] Fetched 140kB in 0s (174kB/s) Selecting previously deselected package bash-completion. (Reading database ... 23808 files and directories currently installed.) Unpacking bash-completion (from .../bash-completion_1%3a1.2-2ubuntu1.1_all.deb) ... Processing triggers for man-db ... Setting up bash-completion (1:1.2-2ubuntu1.1) ... its now kinda working, but still wonky... apt-get ins<tab> gives sudo apt-get insserv as the option. also apt-get install php5<tab> gives apt-get install php5/ not php5-* options.

  Read the article

• Automatically Applying Security Updates for AWS Elastic Beanstalk

  - by Eric Anderson

  I've been a fan of Heroku since it's earliest days. But I like the fact that AWS Elastic Beanstalk gives you more control over the characteristics of the instances. One thing I love about Heroku is the fact that I can deploy an app and not worry about managing it. I am assuming Heroku is ensuring all OS security updates are timely applied. I just need to make sure my app is secure. My initial research on Beanstalk shows that although it builds and configures the instances for you, after that it moves to a more manual management process. Security updates won't automatically be applied to the instances. It seems there are two areas of concerns: New AMI releases - As new AMI releases hit it seems we would want to run the latest (presumably most secure). But my research seems to indicate you need to manually launch a new setup to see the latest AMI version and then create a new environment to use that new version. Is there a better automated way of rotating your instances into new AMI releases? In between releases there will be security updates released for packages. Seems we want to upgrade those as well. My research seems to indicate people install commands to occasionally run a yum update. But since new instances are created/destroyed based on usage it seems that the new instances would not always have the updates (i.e. the time between the instance creation and the first yum update). So occasionally you will have instances that aren't patched. And you are also going to have instances constantly patching themselves until the new AMI release is applied. My other concern is that perhaps these security updates haven't gone through Amazon's own review (like the AMI releases do) and it might break my app to automatically update them. I know Dreamhost once had a 12 hour outage because they were applying debian updates completely automatically without any review. I want to make sure the same thing doesn't happen to me. So my question is does Amazon provide a way to offer fully managed PaaS like Heroku? Or is AWS Elastic Beanstalk really more of just a install script and after that you are on your own (other than the monitoring and deployment tools they provide)?

  Read the article

• Understanding vhosts settings

  - by Matt

  Ok so i have a server and I want to put a few applications on and i am having vhost configuration problems. Here is what i have and I want some direction on what i am doing wrong...ok so the first file is /etc/apache2/ports.conf NameVirtualHost 184.106.111.142:80 Listen 80 <IfModule mod_ssl.c> Listen 443 </IfModule> <IfModule mod_gnutls.c> Listen 443 </IfModule> then i have /etc/apache2/sites-available/somesite.com <VirtualHost 184.106.111.142:80> ServerAdmin [email protected] ServerName somesite.com ServerAlias www.somesite.com DocumentRoot /srv/www/somesite.com/ ErrorLog /srv/www/somesite.com/logs/error.log CustomLog /srv/www/somesite.com/logs/access.log combined <Directory "/srv/www/somesite.com/"> AllowOverride all Options -MultiViews </Directory> </VirtualHost> when i visit somesite.com everything works great but when i add another vhost and lets say thats named anothersite.com. So i have /etc/apache2/sites-available/anothersite.com <VirtualHost 184.106.111.142:80> ServerAdmin [email protected] ServerName anothersite.com ServerAlias www.anothersite.com DocumentRoot /srv/www/anothersite.com/ ErrorLog /srv/www/anothersite.com/logs/error.log CustomLog /srv/www/anothersite.com/logs/access.log combined <Directory "/srv/www/anothersite.com/"> AllowOverride all Options -MultiViews </Directory> </VirtualHost> then i run the following commands >> sudo a2ensite anothersite.com Enabling site anothersite.com. Run '/etc/init.d/apache2 reload' to activate new configuration! >> /etc/init.d/apache2 reload * Reloading web server config apache2 ...done. but when i visit anothersite.com or somesite.com they are both down..What is going on with the vhosts. Could it be the NameVirtualHost declaration with the ip or something...maybe my understanding of vhost settings is not clear. What i dont understand is why do both site now all the sudden not work at all.I would highly appreciate the clarity By the way anothersite.com or somesite.com are the only things I changed to make it more readable

  Read the article

• DNSBL listed at zen.spamhaus.org - cant get outgoing mail working? Am I interpreting the response correctly?

  - by Joe Hopfgartner

  I have problem with a mailserver and there is something I kind of not understand! I can connect, authenticate, specify the sender address - but when specifying the reciever i get a error 550 which looks like so: RCPT TO:[email protected] 550-DNSBL listed at zen.spamhaus.org 550 http://www.spamhaus.org/query/bl?ip=62.178.15.161 Now the strange thing is that 62.178.15.161 is my local client address. Not the servers ip address. Also the error code 550 seems to be defined as so: 550 Requested action not taken: mailbox unavailable To me that makes totally no sense. Why this error code with this spamhaus message? Why the local ip adress and not the servers? There is exim running and there is nothing turning up in the logs mail.err mail.info mail.log mail.warn in /var/log I looked up both the servers and the clients ip adress on blacklists. The clients ip adress is listed on some (as expected), but the server is totally clean. Here is the complete telnet log when I reproduced the error. Mail clients like Evolution and Thunderbird give me the same spamhaus error message. joe@joe-desktop:~$ telnet mail.hunsynth.org 25 Trying 193.164.132.42... Connected to mail.hunsynth.org. Escape character is '^]'. 220 hunsynth.org ESMTP Exim 4.69 Sat, 01 Jan 2011 17:52:45 +0100 HELP 214-Commands supported: 214 AUTH STARTTLS HELO EHLO MAIL RCPT DATA NOOP QUIT RSET HELP EHLO AUTH 250-hunsynth.org Hello chello062178015161.6.11.univie.teleweb.at [62.178.15.161] 250-SIZE 52428800 250-PIPELINING 250-AUTH PLAIN LOGIN CRAM-MD5 250-STARTTLS 250 HELP AUTH LOGIN 334 VXNlcm5hbWU6 dGVzdEBodW5zeW50aC5vcmc= 334 UGFzc3dvcmQ6 ***** 235 Authentication succeeded MAIL FROM:[email protected] 250 OK RCPT TO:[email protected] 550-DNSBL listed at zen.spamhaus.org 550 http://www.spamhaus.org/query/bl?ip=62.178.15.161 quit 221 hunsynth.org closing connection Connection closed by foreign host. joe@joe-desktop:~$ Update: I tried the same thing from my other server and could successfully send an email. So it really looks like the server does check the IP wich establiches the connection is in some blacklist. This is theoretically a good thing - but - the authentication on the server should prevent that? Or shouldn't it? Well I just think it would be absurd if I couldn't send email over my smtp server from my dynamic ISP connection because the dynamic is listed, altough i have a clean server with login?

  Read the article

• NRPE Warning threshold must be a positive integer

  - by Frida

  OS: Ubuntu 12.10 Server 64bits I've installed Icinga, with ido2db, pnp4nagios and icinga-web (last release, following the instruction given in the documentation, installation with apt, etc). I am using icinga-web to monitor my hosts. For the moment, I have just my localhost, and all is perfect. I am trying to add a host and monitor it with NRPE (version 2.12): root@server:/etc/icinga# /usr/lib/nagios/plugins/check_nrpe -H client NRPE v2.12 The configuration looks good. I've created a file in /etc/icinga/objects/client.cfg as below on the server: root@server:/etc/icinga/objects# cat client.cfg define host{ use generic-host ; Name of host template to use host_name client alias client.toto address xx.xx.xx.xx } # Service Definitions define service{ use generic-service host_name client service_description CPU Load check_command check_nrpe_1arg!check_load } define service{ use generic-service host_name client service_description Number of Users check_command check_nrpe_1arg!check_users } And add in my /etc/icinga/commands.cfg: # this command runs a program $ARG1$ with no arguments define command { command_name check_nrpe command_line /usr/lib/nagios/plugins/check_nrpe -H $HOSTADDRESS$ -c $ARG1$ -a $ARG2$ } # this command runs a program $ARG1$ with no arguments define command { command_name check_nrpe_1arg command_line /usr/lib/nagios/plugins/check_nrpe -H $HOSTADDRESS$ -c $ARG1$ } But it does not work. These are the logs from the client: Dec 3 19:45:12 client nrpe[604]: Connection from xx.xx.xx.xx port 32641 Dec 3 19:45:12 client nrpe[604]: Host address is in allowed_hosts Dec 3 19:45:12 client nrpe[604]: Handling the connection... Dec 3 19:45:12 client nrpe[604]: Host is asking for command 'check_users' to be run... Dec 3 19:45:12 client nrpe[604]: Running command: /usr/lib/nagios/plugins/check_users -w -c Dec 3 19:45:12 client nrpe[604]: Command completed with return code 3 and output: check_users: Warning t hreshold must be a positive integer#012Usage:check_users -w -c Dec 3 19:45:12 client nrpe[604]: Return Code: 3, Output: check_users: Warning threshold must be a positive integer#012Usage:check_users -w -c Dec 3 19:44:49 client nrpe[32582]: Connection from xx.xx.xx.xx port 32129 Dec 3 19:44:49 client nrpe[32582]: Host address is in allowed_hosts Dec 3 19:44:49 client nrpe[32582]: Handling the connection... Dec 3 19:44:49 client nrpe[32582]: Host is asking for command 'check_load' to be run... Dec 3 19:44:49 client nrpe[32582]: Running command: /usr/lib/nagios/plugins/check_load -w -c Dec 3 19:44:49 client nrpe[32582]: Command completed with return code 3 and output: Warning threshold mu st be float or float triplet!#012#012Usage:check_load [-r] -w WLOAD1,WLOAD5,WLOAD15 -c CLOAD1,CLOAD5,CLO AD15 Dec 3 19:44:49 client nrpe[32582]: Return Code: 3, Output: Warning threshold must be float or float trip let!#012#012Usage:check_load [-r] -w WLOAD1,WLOAD5,WLOAD15 -c CLOAD1,CLOAD5,CLOAD15 Dec 3 19:44:49 client nrpe[32582]: Connection from xx.xx.xx.xx closed. Have you any ideas?

  Read the article

• IPSEC site-to-site Openswan to Cisco ASA

  - by Jim

  I recieved a list of commands that were run on the right side of the VPN tunnel which is where the Cisco ASA resides. On my side, I have a linux based firewall running debian with openswan installed. I am having an issue with getting to Phase 2 of the VPN negotiation. Here is the Cisco Information I was sent: {my_public_ip} = left side of connection tunnel-group {my_public_ip} type ipsec-l2l tunnel-group {my_public_ip} ipsec-attributes pre-shared-key fakefake crypto map vpn1 1 match add customer-ipsec crypto map vpn1 1 set peer {my_public_ip} crypto map vpn1 1 set transform-set aes-256-sha crypto map vpn1 interface outside static (outside,inside) 10.2.1.200 {my_public_ip} netmask 255.255.255.255 crypto ipsec transform-set aes-256-sha esp-aes-256 esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto map vpn1 1 match address customer-ipsec crypto map vpn1 1 set peer {my_public_ip} crypto map vpn1 1 set transform-set aes-256-sha crypto map vpn1 interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption aes-256 hash sha group 2 lifetime 86400 Myside ipsec.conf config setup klipsdebug=none plutodebug=none protostack=netkey #nat_traversal=yes conn cisco #name of VPN connection type=tunnel authby=secret #left side (myside) left={myPublicIP} leftsubnet=172.16.250.0/24 #net subnet on left sdie to assign to right side leftnexthop=%defaultroute #right security gateway (ASA side) right={CiscoASA_publicIP} #cisco ASA rightsubnet=10.2.1.0/24 rightnexthop=%defaultroute #crypo stuff keyexchange=ike ikelifetime=86400s auth=esp pfs=no compress=no auto=start ipsec.secrets file {CiscoASA_publicIP} {myPublicIP}: PSK "fakefake" When I start ipsec from the left side/my side I don't recieve any errors, however when I run the ipsec auto --status command: 000 "cisco": 172.16.250.0/24==={left_public_ip}<{left_public_ip}>[+S=C]---{left_public_ip_gateway}...{left_public_ip_gateway}--{right_public_ip}<{right_public_ip}>[+S=C]===10.2.1.0/24; prospective erouted; eroute owner: #0 000 "cisco": myip=unset; hisip=unset; 000 "cisco": ike_life: 86400s; ipsec_life: 28800s; rekey_margin: 540s; rekey_fuzz: 100%; keyingtries: 0 000 "cisco": policy: PSK+ENCRYPT+TUNNEL+UP+IKEv2ALLOW+SAREFTRACK+lKOD+rKOD; prio: 24,24; interface: eth0; 000 "cisco": newest ISAKMP SA: #0; newest IPsec SA: #0; 000 000 #2: "cisco":500 STATE_MAIN_I1 (sent MI1, expecting MR1); EVENT_RETRANSMIT in 10s; nodpd; idle; import:admin initiate 000 #2: pending Phase 2 for "cisco" replacing #0 Now I'm new to setting up an site-to-site IPSEC tunnel so the status informatino I am unsure what it means. All I know is it sits at this "pending Phase 2" and I can't ping the other side, Another question I have is, if I do a route -n, should I see anything relating to this connection? Also, I read a few artilcle where configs contained the interface="ipsec0=eth0", is this an interface that I have to create on the linux debian firewall on my side? Appreciate your time to look at this.

  Read the article

• Squid 2.7.STABLE3-4.1 as a transparent proxy on Ubuntu Server 9.04

  - by LOGIC9

  Can't get this to work at all! I'm trying to get this linux box to act as a transparent proxy and, with the help of DHCP, force everyone on the network to gate into the proxy. I have two ethernet connections, both to the same switch. And I'm trying to get 192.168.1.234 to become the default gateway. The actual WAN connection is to a gateway 192.168.1.1. eth0 is 192.168.1.234 eth1 is 192.168.1.2 Effectively I'm trying to make eth0 a LAN only interface and eth1 a WAN interface. I've oi should set the gateway for eth1 to point to 192.168.1.234 my squid.conf file has the following directives added at the bottom: nly set eth0 to have a gateway address in /etc/network/interfaces I'm not sure whether http_port 3128 transparent acl lan src 192.168.1.0/24 acl lh src 127.0.0.1/255.255.255.0 http_access allow lan http_access allow lh i've added the following routing commands: iptables -t nat -A PREROUTING -i eth0 -p tcp -m tcp --dport 80 -j DNAT --to-destination 192.168.1.2:3128 iptables -t nat -A PREROUTING -i eth1 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128 I set a computer with TCP settings 192.168.1.234 as the gateway and opened up google.com, but it comes up with a request error. Any ideas why this isn't working? :( Been searching continuously for a solution to no avail. ----------------------------- EDIT ------------------------------- Managed to get it to route properly to the squid, here's the error I get in the browser: ERROR The requested URL could not be retrieved While trying to process the request: GET / HTTP/1.1 Host: www.google.com User-Agent: Mozilla/5.0 (Windows; U; Windows NT 5.1; en-GB; rv:1.9.1.2) Gecko/20090729 Firefox/3.5.2 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-gb,en;q=0.5 Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 300 Connection: keep-alive Cache-Control: max-age=0 The following error was encountered: * Invalid Request Some aspect of the HTTP Request is invalid. Possible problems: * Missing or unknown request method * Missing URL * Missing HTTP Identifier (HTTP/1.0) * Request is too large * Content-Length missing for POST or PUT requests * Illegal character in hostname; underscores are not allowed Your cache administrator is webmaster. Generated Mon, 26 Oct 2009 03:41:15 GMT by mjolnir.lloydharrington.local (squid/2.7.STABLE3)

  Read the article

• Windows 7 remains powered on when restarting

  - by BombDefused

  I'm running windows 7 x64 on an MSI P67A-GD53 motherboard, in an Antec P280 Super Midi Towercase with a Corsair 650w PSU. I've just installed a second instance of windows 7 x64 on a separate disk (this is to keep my games separate from my work OS). The problem is that it appears now that I cannot restart from either instance of Windows 7. The shut down command, and sleep commands work as expected. When I try to restart, the shutdown happens but the system never reboots. Everything remains powered on, until I hold down the power button to force the power off. Ithink (but am not 100% sure) this has only started since I installed the second OS, and am assuming this has something to do with the motherboard needing to know which OS to run up again? Some other forums I've read suggest that the PSU has a major role in restart and could be at fault. Changing the boot order of the disks in the BIOS does not change anything. Any suggestions greatfully recieved! Update: I now have a reproduceable issue: I think the secondary OS install may have been a red herring. It was when windows tried to reboot during the install that I noticed the issue. After playing around with installing drivers, and rebooting many many times, I have found that it is the OC genie setting on the MSI motherboard that seems to trigger the problem. This makes sense as I only started using the OC genie feature a couple of weeks ago, and probably hadn't used restart in that time. However... simply turning off OC genie does not make the issue go away. I have to turn off OC genie, shutdown, start enter bios, go to the "Save and Exit" menu "Restore Defaults" yes to "Load optimized defaults", which will reset to clear the problem. Now when the PC boots into windows, I can restart as normal (and from the OS on either HDD). I only know how to control the issue, and don't still know the root cause. I'd like to be able to use the OC genie function if anyone can suggest a why I'm seeing this problem. Could it be that I'm drawing too much power when using OC feature?

  Read the article

• Detecting upload success/failure in a scripted command-line SFTP session?

  - by Will Martin

  I am writing a BASH shell script to upload all the files in a directory to a remote server and then delete them. It'll run every few hours via a CRON job. My complete script is below. The basic problem is that the part that's supposed to figure out whether the file uploaded successfully or not doesn't work. The SFTP command's exit status is always "0" regardless of whether the upload actually succeeded or not. How can I figure out whether a file uploaded correctly or not so that I can know whether to delete it or let it be? #!/bin/bash # First, save the folder path containing the files. FILES=/home/bob/theses/* # Initialize a blank variable to hold messages. MESSAGES="" ERRORS="" # These are for notifications of file totals. COUNT=0 ERRORCOUNT=0 # Loop through the files. for f in $FILES do # Get the base filename BASE=`basename $f` # Build the SFTP command. Note space in folder name. CMD='cd "Destination Folder"\n' CMD="${CMD}put ${f}\nquit\n" # Execute it. echo -e $CMD | sftp -oIdentityFile /home/bob/.ssh/id_rsa [email protected] # On success, make a note, then delete the local copy of the file. if [ $? == "0" ]; then MESSAGES="${MESSAGES}\tNew file: ${BASE}\n" (( COUNT=$COUNT+1 )) # Next line commented out for ease of testing #rm $f fi # On failure, add an error message. if [ $? != "0" ]; then ERRORS="${ERRORS}\tFailed to upload file ${BASE}\n" (( ERRORCOUNT=$ERRORCOUNT+1 )) fi done SUBJECT="New Theses" BODY="There were ${COUNT} files and ${ERRORCOUNT} errors in the latest batch.\n\n" if [ "$MESSAGES" != "" ]; then BODY="${BODY}New files:\n\n${MESSAGES}\n\n" fi if [ "$ERRORS" != "" ]; then BODY="${BODY}Problem files:\n\n${ERRORS}" fi # Send a notification. echo -e $BODY | mail -s $SUBJECT [email protected] Due to some operational considerations that make my head hurt, I cannot use SCP. The remote server is using WinSSHD on windows, and does not have EXEC privileges, so any SCP commands fail with the message "Exec request failed on channel 0". The uploading therefore has to be done via the interactive SFTP command.

  Read the article

• Static IPv6 address in Windows unused for outgoing connections

  - by Luc

  I'm running a Windows server and trying to get it to use a static IPv6 address for outgoing connections to other IPv6 hosts (such as Gmail). I need this because Gmail requires a ptr record, and I can't set one for random addresses. The static address is configured on the host, but it also has a temporary privacy address as well as a random address from the router it seems. By default Windows uses the privacy address; it seems this is the expected behavior (and it makes perfect sense for people/users that did not set a static address, but I did!). I've tried disabling the privacy address with: netsh int ipv6 set privacy disabled This indeed gets rid of the privacy address, but I still have the random address that the router assigned. To disable this, it was said I needed to disable "router discovery" using this command: net interface ipv6 set interface 14 routerdiscovery=disabled Upon doing this, all IPv6 connectivity is lost. If I do this while pinging Gmail, it will report "Destination host unreachable" as soon as I enter the command. In the static IPv6 configuration, I did configure the default gateway and prefix length, so I don't see why it's unable to connect. Probably has something to do with the lack of ARP in IPv6 and somehow being unable to resolve the router's MAC, but I wouldn't know how to fix this. Finally I've tried disabling the DHCPv6 lease with these commands: netsh interface ipv6 set interface "IDMZ Team" managedaddress=disabled netsh interface ipv6 set interface "IDMZ Team" otherstateful=disabled Which was to no avail; the host continues to obtain and use the router-assigned IPv6 address. The router is a FritzBox 7340, which shows me all the IPv4 and IPv6 addresses that the host (identified by MAC) utilizes, but I'm unable to change the assigned address. Maybe this could be done over the telnet interface of the router somehow, but again, I wouldn't know how to do this even if it's the way to go. In short, any of the following would probably solve my problem: Change Windows' source address selection behavior. Have Windows not get an address from the router and not generate a privacy address; Have the router hand out a static address and make Windows use that as source address. Recover connectivity after disabling router discovery on Windows. Alternatively I might use some (batch, perl, ...) script to throw away all IPv6 addresses except the desired one, but this feels rather hacky. If it's the only way (or less hacky than another hacky solution), it might be an option though. Thanks!

  Read the article

• Solaris10 x86 mirror. Making second disk booteable when failure

  - by Kani

  Did a mirror (RAID1) with Solaris 10 in x86. Everything OK. Now, I´m trying to make the second disk booteable, this is: from grub or in case of failure of disk1. I edited /boot/grub/menu.lst: #---------- ADDED BY BOOTADM - DO NOT EDIT ---------- title Solaris 10 9/10 s10x_u9wos_14a X86 findroot (rootfs1,0,a) kernel /platform/i86pc/multiboot module /platform/i86pc/boot_archive #---------------------END BOOTADM-------------------- #---------- ADDED BY BOOTADM - DO NOT EDIT ---------- title Solaris failsafe findroot (rootfs1,0,a) kernel /boot/multiboot -s module /boot/amd64/x86.miniroot-safe #---------------------END BOOTADM-------------------- #---------- ADDED BY BOOTADM - DO NOT EDIT ---------- title Solaris failsafe findroot (rootfs1,0,a) kernel /boot/multiboot kernel/unix -s module /boot/x86.miniroot-safe #---------------------END BOOTADM-------------------- #Make second disk booteable!!!!!!! title alternate boot findroot (rootfs1,1,a) kernel /boot/multiboot kernel/unix -s module /boot/x86.miniroot-safe But is not working. In the BIOS, when I select "alternate boot" I get: Error 15: 15 file not found also, how to configure to GRUB to make the disk2 to boot in case of error in disk1? Additionally, I did (but not related to GRUB): eeprom altbootpath=/devices/pci@0,0/pci108e,5352@1f,2/disk@1,0:a Here is the output of some commands that may help you: /sbin/biosdev 0x80 /pci@0,0/pci108e,5352@1f,2/disk@0,0 0x81 /pci@0,0/pci108e,5352@1f,2/disk@1,0 ls -l /dev/dsk/c1t?d0s0 lrwxrwxrwx 1 root root 50 Jul 7 12:01 /dev/dsk/c1t0d0s0 -> ../../devices/pci@0,0/pci108e,5352@1f,2/disk@0,0:a lrwxrwxrwx 1 root root 50 Jul 7 12:01 /dev/dsk/c1t1d0s0 -> ../../devices/pci@0,0/pci108e,5352@1f,2/disk@1,0:a more /boot/solaris/bootenv.rc setprop ata-dma-enabled '1' setprop atapi-cd-dma-enabled '0' setprop ttyb-rts-dtr-off 'false' setprop ttyb-ignore-cd 'true' setprop ttya-rts-dtr-off 'false' setprop ttya-ignore-cd 'true' setprop ttyb-mode '9600,8,n,1,-' setprop ttya-mode '9600,8,n,1,-' setprop lba-access-ok '1' setprop prealloc-chunk-size '0x2000' setprop bootpath '/pci@0,0/pci108e,5352@1f,2/disk@0,0:a' setprop keyboard-layout 'US-English' setprop console 'text' setprop altbootpath '/pci@0,0/pci108e,5352@1f,2/disk@1,0:a' cat /etc/vfstab #device device mount FS fsck mount mount #to mount to fsck point type pass at boot options # fd - /dev/fd fd - no - /proc - /proc proc - no - #/dev/dsk/c1t0d0s1 - - swap - no - /dev/md/dsk/d1 - - swap - no - /dev/md/dsk/d0 /dev/md/rdsk/d0 / ufs 1 no - /devices - /devices devfs - no - sharefs - /etc/dfs/sharetab sharefs - no - ctfs - /system/contract ctfs - no - objfs - /system/object objfs - no - swap - /tmp tmpfs - yes - df -h Filesystem size used avail capacity Mounted on /dev/md/dsk/d0 909G 11G 889G 2% / /devices 0K 0K 0K 0% /devices ctfs 0K 0K 0K 0% /system/contract proc 0K 0K 0K 0% /proc mnttab 0K 0K 0K 0% /etc/mnttab swap 14G 972K 14G 1% /etc/svc/volatile objfs 0K 0K 0K 0% /system/object sharefs 0K 0K 0K 0% /etc/dfs/sharetab /usr/lib/libc/libc_hwcap1.so.1 909G 11G 889G 2% /lib/libc.so.1 fd 0K 0K 0K 0% /dev/fd swap 14G 40K 14G 1% /tmp swap 14G 28K 14G 1% /var/run

  Read the article

• DNS and DHCP dies after ~2 days of use on ClearOS

  - by TheLQ

  I'm using ClearOS (based on CentOS, so any info specific to it should apply here) as a gateway, DHCP, and DNS server. I had this server running perfectly for a month or two before replacing it with another server. However due DNS and DHCP failing 2 days in and a host of other performance issues (the box was a little underpowered), I changed back to the origional server. However 2 days in DHCP and DNS are failing again, and I'm out of idea's on why. In both cases to my knowledge no network or server changes occurred after installation. Right after installing (and at least a day in) DNS and DHCP was working just fine. However later (Day 2) I get a call saying their internet is down (translation: Nobody can get to websites because DNS is down) I've tried to fix the problem by checking if the dnsmasq is even running (it is), restarting the service, and restarting the server to no effect. I do have two internal servers that have static DHCP leases but one's lease must of expired as I can't connect to it anymore. I'm hesitant to do any dhcp testing on the last server as I'll not be able to connect to it anymore. Is there anything anyone can think of on why DNS and DHCP would fail 2 days in to running perfectly? More info: Running dnsmasq in debug mode. This is all that's displayed even when running nslookup quackwall. I'm not sure though if nslookup commands should show up in the log [root@quackwall ~]# /usr/sbin/dnsmasq -dq dnsmasq: started, version 2.49 cachesize 150 dnsmasq: compile time options: IPv6 GNU-getopt no-DBus no-I18N DHCP TFTP dnsmasq-dhcp: DHCP, IP range 10.0.0.100 -- 10.0.0.254, lease time 12h dnsmasq: reading /etc/resolv.conf dnsmasq: using nameserver 74.128.17.114#53 dnsmasq: using nameserver 74.128.19.102#53 dnsmasq: read /etc/hosts - 5 addresses dnsmasq-dhcp: read /etc/ethers - 2 addresses On the other server DNS and the Gateway are all configured correctly (10.0.0.2 is quackwall) lordquackstar@quackgame:~$ netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 10.0.0.0 0.0.0.0 255.255.240.0 U 0 0 0 eth0 0.0.0.0 10.0.0.2 0.0.0.0 UG 0 0 0 eth0 lordquackstar@quackgame:~$ cat /etc/resolv.conf nameserver 10.0.0.2 domain highwow.lan search highwow.lan

  Read the article

• Slow Memcached: Average 10ms memcached `get`

  - by Chris W.

  We're using Newrelic to measure our Python/Django application performance. Newrelic is reporting that across our system "Memcached" is taking an average of 12ms to respond to commands. Drilling down into the top dozen or so web views (by # of requests) I can see that some Memcache get take up to 30ms; I can't find a single use of Memcache get that returns in less than 10ms. More details on the system architecture: Currently we have four application servers each of which has a memcached member. All four memcached members participate in a memcache cluster. We're running on a cloud hosting provider and all traffic is running across the "internal" network (via "internal" IPs) When I ping from one application server to another the responses are in ~0.5ms Isn't 10ms a slow response time for Memcached? As far as I understand if you think "Memcache is too slow" then "you're doing it wrong". So am I doing it wrong? Here's the output of the memcache-top command: memcache-top v0.7 (default port: 11211, color: on, refresh: 3 seconds) INSTANCE USAGE HIT % CONN TIME EVICT/s GETS/s SETS/s READ/s WRITE/s cache1:11211 37.1% 62.7% 10 5.3ms 0.0 73 9 3958 84.6K cache2:11211 42.4% 60.8% 11 4.4ms 0.0 46 12 3848 62.2K cache3:11211 37.5% 66.5% 12 4.2ms 0.0 75 17 6056 170.4K AVERAGE: 39.0% 63.3% 11 4.6ms 0.0 64 13 4620 105.7K TOTAL: 0.1GB/ 0.4GB 33 13.9ms 0.0 193 38 13.5K 317.2K (ctrl-c to quit.) ** Here is the output of the top command on one machine: ** (Roughly the same on all cluster machines. As you can see there is very low CPU utilization, because these machines only run memcache.) top - 21:48:56 up 1 day, 4:56, 1 user, load average: 0.01, 0.06, 0.05 Tasks: 70 total, 1 running, 69 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.0%sy, 0.0%ni, 99.7%id, 0.0%wa, 0.0%hi, 0.0%si, 0.3%st Mem: 501392k total, 424940k used, 76452k free, 66416k buffers Swap: 499996k total, 13064k used, 486932k free, 181168k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 6519 nobody 20 0 384m 74m 880 S 1.0 15.3 18:22.97 memcached 3 root 20 0 0 0 0 S 0.3 0.0 0:38.03 ksoftirqd/0 1 root 20 0 24332 1552 776 S 0.0 0.3 0:00.56 init 2 root 20 0 0 0 0 S 0.0 0.0 0:00.00 kthreadd 4 root 20 0 0 0 0 S 0.0 0.0 0:00.00 kworker/0:0 5 root 20 0 0 0 0 S 0.0 0.0 0:00.02 kworker/u:0 6 root RT 0 0 0 0 S 0.0 0.0 0:00.00 migration/0 7 root RT 0 0 0 0 S 0.0 0.0 0:00.62 watchdog/0 8 root 0 -20 0 0 0 S 0.0 0.0 0:00.00 cpuset 9 root 0 -20 0 0 0 S 0.0 0.0 0:00.00 khelper ...output truncated...

  Read the article

• NetApp erroring with: STATUS_NOLOGON_WORKSTATION_TRUST_ACCOUNT

  - by Sobrique

  Since a sitewide upgrade to Windows 7 on desktop, I've started having a problem with virus checking. Specifically - when doing a rename operation on a (filer hosted) CIFS share. The virus checker seems to be triggering a set of messages on the filer: [filerB: auth.trace.authenticateUser.loginTraceIP:info]: AUTH: Login attempt by user server-wk8-r2$ of domain MYDOMAIN from client machine 10.1.1.20 (server-wk8-r2). [filerB: auth.dc.trace.DCConnection.statusMsg:info]: AUTH: TraceDC- attempting authentication with domain controller \\MYDC. [filerB: auth.trace.authenticateUser.loginRejected:info]: AUTH: Login attempt by user rejected by the domain controller with error 0xc0000199: STATUS_NOLOGON_WORKSTATION_TRUST_ACCOUNT. [filerB: auth.trace.authenticateUser.loginTraceMsg:info]: AUTH: Delaying the response by 5 seconds due to continuous failed login attempts by user server-wk8-r2$ of domain MYDOMAIN from client machine 10.1.1.20. This seems to specifically trigger on a rename so what we think is going on is the virus checker is seeing a 'new' file, and trying to do an on-access scan. The virus checker - previously running as LocalSystem and thus sending null as it's authentication request is now looking rather like a DOS attack, and causing the filer to temporarily black list. This 5s lock out each 'access attempt' is a minor nuisance most of the time, and really quite significant for some operations - e.g. large file transfers, where every file takes 5s Having done some digging, this seems to be related to NLTM authentication: Symptoms Error message: System error 1808 has occurred. The account used is a computer account. Use your global user account or local user account to access this server. A packet trace of the failure will show the error as: STATUS_NOLOGON_WORKSTATION_TRUST_ACCOUNT (0xC0000199) Cause Microsoft has changed the functionality of how a Local System account identifies itself during NTLM authentication. This only impacts NTLM authentication. It does not impact Kerberos Authentication. Solution On the host, please set the following group policy entry and reboot the host. Network Security: Allow Local System to use computer identity for NTLM: Disabled Defining this group policy makes Windows Server 2008 R2 and Windows 7 function like Windows Server 2008 SP1. So we've now got a couple of workaround which aren't particularly nice - one is to change this security option. One is to disable virus checking, or otherwise exempt part of the infrastructure. And here's where I come to my request for assistance from ServerFault - what is the best way forwards? I lack Windows experience to be sure of what I'm seeing. I'm not entirely sure why NTLM is part of this picture in the first place - I thought we were using Kerberos authentication. I'm not sure how to start diagnosing or troubleshooting this. (We are going cross domain - workstation machine accounts are in a separate AD and DNS domain to my filer. Normal user authentication works fine however.) And failing that, can anyone suggest other lines of enquiry? I'd like to avoid a site wide security option change, or if I do go that way I'll need to be able to supply detailed reasoning. Likewise - disabling virus checking works as a short term workaround, and applying exclusions may help... but I'd rather not, and don't think that solves the underlying problem. EDIT: Filers in AD ldap have SPNs for: nfs/host.fully.qualified.domain nfs/host HOST/host.fully.qualified.domain HOST/host (Sorry, have to obfuscate those). Could it be that without a 'cifs/host.fully.qualified.domain' it's not going to work? (or some other SPN? ) Edit: As part of the searching I've been doing I've found: http://itwanderer.wordpress.com/2011/04/14/tread-lightly-kerberos-encryption-types/ Which suggests that several encryption types were disabled by default in Win7/2008R2. This might be pertinent, as we've definitely had a similar problem with Keberized NFSv4. There is a hidden option which may help some future Keberos users: options nfs.rpcsec.trace on (This hasn't given me anything yet though, so may just be NFS specific). Edit: Further digging has me tracking it back to cross domain authentication. It looks like my Windows 7 workstation (in one domain) is not getting Kerberos tickets for the other domain, in which my NetApp filer is CIFS joined. I've done this separately against a standalone server (Win2003 and Win2008) and didn't get Kerberos tickets for those either. Which means I think Kerberos might be broken, but I've no idea how to troubleshoot further. Edit: A further update: It looks like this may be down Kerberos tickets not being issued cross domain. This then triggers NTLM fallback, which then runs into this problem (since Windows 7). First port of call will be to investigate the Kerberos side of things, but in neither case do we have anything pointing at the Filer being the root cause. As such - as the storage engineer - it's out of my hands. However, if anyone can point me in the direction of troubleshooting Kerberos spanning two Windows AD domains (Kerberos Realms) then that would be appreciated. Options we're going to be considering for resolution: Amend policy option on all workstations via GPO (as above). Talking to AV vendor about the rename triggering scanning. Talking to AV vendor regarding running AV as service account. investigating Kerberos authentication (why it's not working, whether it should be).

  Read the article

• VMWare tools not installing with an error

  - by JDS

  VMWare tools not installing on Ubuntu 12.04. I'm using Chef to manage the installation, but the Apt commands fail if run manually. I'm using the VMWare tool Debian repo. Example: $ cat /etc/apt/sources.list.d/vmware-tools-source.list deb http://packages.vmware.com/tools/esx/5.0u2/ubuntu precise main When trying to install, most packages seem to go ok, but one, "vmware-tools-foundation", does not. Example: $ apt-get -q -y install vmware-tools-esx-nox=8.6.10-1.precise Reading package lists... Building dependency tree... Reading state information... You might want to run 'apt-get -f install' to correct these: The following packages have unmet dependencies: vmware-tools-esx-kmods-3.2.0-23-generic : Depends: vmware-tools-foundation (>= 8.6.10) but it is not going to be installed vmware-tools-esx-nox : Depends: ...snip list of deps... E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution). $ apt-get -f install Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following extra packages will be installed: vmware-tools-foundation The following NEW packages will be installed: vmware-tools-foundation 0 upgraded, 1 newly installed, 0 to remove and 118 not upgraded. 7 not fully installed or removed. Need to get 0 B/5,886 B of archives. After this operation, 86.0 kB of additional disk space will be used. Do you want to continue [Y/n]? y (Reading database ... 103499 files and directories currently installed.) Unpacking vmware-tools-foundation (from .../vmware-tools-foundation_8.6.10-1.precise_all.deb) ... VMware Tools cannot install because it appears that another installation of VMware Tools is already present. Please remove the previous installation and then attempt to install this copy of VMware Tools again. dpkg: error processing /var/cache/apt/archives/vmware-tools-foundation_8.6.10-1.precise_all.deb (--unpack): subprocess new pre-installation script returned error exit status 1 Errors were encountered while processing: /var/cache/apt/archives/vmware-tools-foundation_8.6.10-1.precise_all.deb E: Sub-process /usr/bin/dpkg returned an error code (1) The key seems to be this error: "VMware Tools cannot install because it appears that another installation of VMware Tools is already present. Please remove the previous installation and then attempt to install this copy of VMware Tools again." However, I've tryed removing and purging and can't seem to "trick" VMWare tools into thinking the packages are gone. Apt thinks they are gone. Is there some service/file/cache/lock left that VMWare tools sees that makes it think that VMWare tools are still installed? I've googled and googled but there is no answer to this question with my particular circumstances on the interwebs. VMWare's documentation of this error is minimal.

  Read the article

• Can't get Apache 2.2.21 to compile with OpenSSL support

  - by angstwad

  Alright -- having a bad couple days here compiling Apache 2.2.21 on CentOS 5.7 with the following configure commands: ./configure --enable-ssl=shared --with-ssl=/usr/local/openssl I've compiled from source OpenSSL 1.0.0e from source: ./config --prefix=/usr/local --openssldir=/usr/local/openssl shared zlib-dynamic I attempt to start Apache and it returns: httpd: Syntax error on line 54 of /usr/local/apache2/conf/httpd.conf: Cannot load /usr/local/apache2/modules/mod_ssl.so into server: /usr/local/apache2/modules/mod_ssl.so: undefined symbol: SSL_get_servername If I look at how the libraries are linked, this is what I get: [root@web1 modules]# ldd mod_ssl.so libssl.so.6 => /lib64/libssl.so.6 (0x00002aaaaace4000) libcrypto.so.6 => /lib64/libcrypto.so.6 (0x00002aaaaaf30000) libdl.so.2 => /lib64/libdl.so.2 (0x00002aaaab281000) libz.so.1 => /lib64/libz.so.1 (0x00002aaaab486000) libpthread.so.0 => /lib64/libpthread.so.0 (0x00002aaaab69a000) libc.so.6 => /lib64/libc.so.6 (0x00002aaaab8b5000) libgssapi_krb5.so.2 => /usr/lib64/libgssapi_krb5.so.2 (0x00002aaaabc0e000) libkrb5.so.3 => /usr/lib64/libkrb5.so.3 (0x00002aaaabe3c000) libcom_err.so.2 => /lib64/libcom_err.so.2 (0x00002aaaac0d1000) libk5crypto.so.3 => /usr/lib64/libk5crypto.so.3 (0x00002aaaac2d4000) /lib64/ld-linux-x86-64.so.2 (0x0000555555554000) libkrb5support.so.0 => /usr/lib64/libkrb5support.so.0 (0x00002aaaac4f9000) libkeyutils.so.1 => /lib64/libkeyutils.so.1 (0x00002aaaac702000) libresolv.so.2 => /lib64/libresolv.so.2 (0x00002aaaac904000) libselinux.so.1 => /lib64/libselinux.so.1 (0x00002aaaacb19000) libsepol.so.1 => /lib64/libsepol.so.1 (0x00002aaaacd32000) Basically, I've tired compiling from source OpenSSL (both 0.9.8r and 1e), having yum reinstall from the repos, done a make clean and remade both OpenSSL and Apache numerous times -- but I can't get it to compile into the apache base or dynamically as a shared object file. What am I doing wrong here? Update 1: After doing a make clean and make distclean, I've reconfigured with the same parameters as above without any effect. The config.log is at Pastebin. Update 2: Modifying the LD_LIBRARY_PATH had no effect on the lib-deps of mod_ssl.so. UPDATE 3: I've compiled and recompiled many times, and verified with ldconfig that the OpenSSL libs dir is in my path, and included in ld.so.conf. Still cannot get httpd/mod_ssl to load the library at runtime.

  Read the article

• How to move a ruby on rails application to a new server

  - by ManiacZX

  I have a rails app on an old Ubuntu server I need to move onto a new machine. I haven't worked with ruby on rails so I don't really know anything about the structure of the app. I want to load this onto an Ubuntu 8.04 AMI on Amazon EC2 and am looking for any information regarding the migration process such as: Do I copy over the entire folder defined as the application root in the mongrel config (for ex: /u/apps/myapp/current) or just certain folders? Am I looking for trouble if I go with the latest versions of ruby and the various gems? Any general gotchas to look out for in the process. Current server information: root@webnode001:/# cat /proc/version Linux version 2.6.15-27-server (buildd@terranova) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 SMP Fri Dec 8 18:43:54 UTC 2006 root@webnode001:/# rails -v Rails 1.2.3 root@webnode001:/# mongrel_rails cluster::configure --version Version 1.0.1 root@webnode001:/# gem -v 0.9.0 root@webnode001:/# gem list -l *** LOCAL GEMS *** actionmailer (1.3.3, 1.2.5) Service layer for easy email delivery and testing. actionpack (1.13.3, 1.12.5) Web-flow and rendering framework putting the VC in MVC. actionwebservice (1.2.3, 1.1.6) Web service support for Action Pack. activerecord (1.15.3, 1.15.2, 1.14.4) Implements the ActiveRecord pattern for ORM. activesupport (1.4.2, 1.4.1, 1.3.1) Support and utility classes used by the Rails framework. cgi_multipart_eof_fix (2.1) Fix an exploitable bug in CGI multipart parsing which affects Ruby <= 1.8.5 when multipart boundary attribute contains a non-halting regular expression string. daemons (1.0.7, 1.0.5, 1.0.4, 1.0.2) A toolkit to create and control daemons in different ways eventmachine (0.7.2, 0.7.0) Ruby/EventMachine socket engine library fastercsv (1.2.0, 1.1.0) FasterCSV is CSV, but faster, smaller, and cleaner. fastthread (1.0) Optimized replacement for thread.rb primitives ferret (0.11.4) Ruby indexing library. gem_plugin (0.2.2, 0.2.1) A plugin system based only on rubygems that uses dependencies only mongrel (1.0.1, 0.3.13.4) A small fast HTTP library and server that runs Rails, Camping, Nitro and Iowa apps. mongrel_cluster (0.2.1) Mongrel plugin that provides commands and Capistrano tasks for managing multiple Mongrel processes. mysql (2.7) MySQL/Ruby provides the same functions for Ruby programs that the MySQL C API provides for C programs. piston (1.3.3) Piston is a utility that enables merge tracking of remote repositories. rails (1.2.3, 1.1.6) Web-application framework with template engine, control-flow layer, and ORM. rake (0.7.3, 0.7.1) Ruby based make-like utility. sources (0.0.1) This package provides download sources for remote gem installation swiftiply (0.5.1) A fast clustering proxy for web applications.

  Read the article

• Starting/Stopping Custom PHP Chat Server Linux Service (CentOS)

  - by chad

  I have been trying all night to get this service working properly. I created this script from a template and am very new to bash coding. I wrote a fully functioning chat server in php which runs endlessly, but now want to make it a dedicated service. I want to do this so that it starts on server boot and boots back up if possible when there are any down-times with the server. The issue is that I need this thing to run in a detached screen so that I can monitor packet data or send server commands via SSH when need-be. The main problem that i'm having is that it needs to have its own PID when it starts so that I can stop/restart it when needed. I am the type who grinds on coding until I figure it out, but this is so new to me that it seems the learning curve here is very steep and frustrating. Below is my code if anybody can please help me with this one, i've gotten so tired I can't even concentrate any more :( #!/bin/sh # # chatserver # # chkconfig: 345 20 90 # description: chatServer Linux Service Daemon \ # for general server handling ### BEGIN INIT INFO # Provides: chatserver # Required-Start: $local_fs $network $named $syslog # Required-Stop: $local_fs $syslog # Default-Start: 3 4 5 # Default-Stop: 0 1 2 6 # Short-Description: This service maintains the chatServer # Description: chatServer Linux Service Daemon # for general server handling ### END INIT INFO # Source function library. . /etc/rc.d/init.d/functions exec="screen php -q /var/www/html/chatServer.php" prog="chatserver" config="/etc/sysconfig/$prog" pidfile="/var/run/chatserver.pid" [ -e /etc/sysconfig/$prog ] && . /etc/sysconfig/$prog lockfile=/var/lock/subsys/$prog start() { #$exec || exit 5 echo -n $"Starting $prog: " daemon $exec --name=$exec --pidfile=$pidfile retval=$? echo [ $retval -eq 0 ] && touch $lockfile return $retval } stop() { echo -n $"Stopping $prog: " killproc -p $pidfile rm -f $pidfile retval=$? echo [ $retval -eq 0 ] && rm -f $lockfile return $retval } restart() { stop start } reload() { restart } force_reload() { restart } rh_status() { # run checks to determine if the service is running or use generic status status $prog } rh_status_q() { rh_status >/dev/null 2>&1 } case "$1" in start) rh_status_q && exit 0 $1 ;; stop) rh_status_q || exit 0 $1 ;; restart) $1 ;; reload) rh_status_q || exit 7 $1 ;; force-reload) force_reload ;; status) rh_status ;; condrestart|try-restart) rh_status_q || exit 0 restart ;; *) echo $"Usage: $0 {start|stop|status|restart|condrestart|try-restart|reload|force-reload}" exit 2 esac exit $?

  Read the article

• postfix error: open database /var/lib/mailman/data/aliases.db: No such file

  - by Thufir

  In trying to follow the Ubuntu guide for postfix and mailman, I do not understand these directions: This build of mailman runs as list. It must have permission to read /etc/aliases and read and write /var/lib/mailman/data/aliases. Do this with these commands: sudo chown root:list /var/lib/mailman/data/aliases sudo chown root:list /etc/aliases Save and run: sudo newaliases I'm getting this kind of error: root@dur:~# root@dur:~# root@dur:~# telnet localhost 25 Trying 127.0.0.1... Connected to localhost. Escape character is '^]'. 220 dur.bounceme.net ESMTP Postfix (Ubuntu) ehlo dur 250-dur.bounceme.net 250-PIPELINING 250-SIZE 10240000 250-VRFY 250-ETRN 250-STARTTLS 250-ENHANCEDSTATUSCODES 250-8BITMIME 250 DSN quit 221 2.0.0 Bye Connection closed by foreign host. root@dur:~# root@dur:~# tail /var/log/mail.log Aug 28 01:16:43 dur postfix/master[19444]: terminating on signal 15 Aug 28 01:16:43 dur postfix/postfix-script[19558]: starting the Postfix mail system Aug 28 01:16:43 dur postfix/master[19559]: daemon started -- version 2.9.1, configuration /etc/postfix Aug 28 01:16:45 dur postfix/postfix-script[19568]: stopping the Postfix mail system Aug 28 01:16:45 dur postfix/master[19559]: terminating on signal 15 Aug 28 01:16:45 dur postfix/postfix-script[19673]: starting the Postfix mail system Aug 28 01:16:45 dur postfix/master[19674]: daemon started -- version 2.9.1, configuration /etc/postfix Aug 28 01:17:22 dur postfix/smtpd[19709]: error: open database /var/lib/mailman/data/aliases.db: No such file or directory Aug 28 01:17:22 dur postfix/smtpd[19709]: connect from localhost[127.0.0.1] Aug 28 01:18:37 dur postfix/smtpd[19709]: disconnect from localhost[127.0.0.1] root@dur:~# root@dur:~# postconf -n alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases, hash:/var/lib/mailman/data/aliases append_dot_mydomain = no biff = no broken_sasl_auth_clients = yes config_directory = /etc/postfix default_transport = smtp home_mailbox = Maildir/ inet_interfaces = loopback-only mailbox_command = /usr/lib/dovecot/deliver -c /etc/dovecot/conf.d/01-mail-stack-delivery.conf -m "${EXTENSION}" mailbox_size_limit = 0 mailman_destination_recipient_limit = 1 mydestination = dur, dur.bounceme.net, localhost.bounceme.net, localhost myhostname = dur.bounceme.net mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 readme_directory = no recipient_delimiter = + relay_domains = lists.dur.bounceme.net relay_transport = relay relayhost = smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtp_use_tls = yes smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_recipient_restrictions = reject_unknown_sender_domain, reject_unknown_recipient_domain, reject_unauth_pipelining, permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination smtpd_sasl_auth_enable = yes smtpd_sasl_authenticated_header = yes smtpd_sasl_local_domain = $myhostname smtpd_sasl_path = private/dovecot-auth smtpd_sasl_security_options = noanonymous smtpd_sasl_type = dovecot smtpd_tls_auth_only = yes smtpd_tls_cert_file = /etc/ssl/certs/ssl-mail.pem smtpd_tls_key_file = /etc/ssl/private/ssl-mail.key smtpd_tls_mandatory_ciphers = medium smtpd_tls_mandatory_protocols = SSLv3, TLSv1 smtpd_tls_received_header = yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes tls_random_source = dev:/dev/urandom transport_maps = hash:/etc/postfix/transport root@dur:~# root@dur:~# And am wondering what connection might be. I do see that I don't have the requisite files: root@dur:~# root@dur:~# ll /var/lib/mailman/data/aliases ls: cannot access /var/lib/mailman/data/aliases: No such file or directory root@dur:~# At what stage were those aliases created? How can I create them? Is that what's causing the error error: open database /var/lib/mailman/data/aliases.db: No such file or directory Aug 28 01:17:22 dur postfix/smtpd[19709]: connect from localhost[127.0.0.1]?

  Read the article

< Previous Page | 223 224 225 226 227 228 229 230 231 232 233 234  | Next Page >