Search Results

Search found 11032 results on 442 pages for 'opensuse 12 2'.

Page 228/442 | < Previous Page | 224 225 226 227 228 229 230 231 232 233 234 235  | Next Page >

  • multicast and iptables

    - by Massimo
    I have secured a linux box, starting with iptables -P INPUT DROP iptables -P OUTPUT DROP iptables -P FORWARD DROP and after adding rules to enable specific protocols and streams. Which are the correct rules to add multicast support ? I am trying with these - for both client and server multicast : iptables -A INPUT -m pkttype --pkt-type multicast -j ACCEPT iptables -A OUTPUT -m pkttype --pkt-type multicast -j ACCEPT iptables -A INPUT --protocol igmp -j ACCEPT iptables -A OUTPUT --protocol igmp -j ACCEPT iptables -A INPUT --dst "224.0.0.0/4" -j ACCEPT iptables -A OUTPUT --dst "224.0.0.0/4" -j ACCEPT Linux 2.6.38-12 / iptables 1.4.10 Is there any internet service to test my multicast set ( pc + adsl router + provider ) ?

    Read the article

  • Nagios remote monitoring: NRPE Vs. SSH

    - by sam
    We use Nagios to monitor quite a few (~130) servers. We monitor CPU, Disk, RAM and a few other things on each server. I've always used SSH to run the remote commands, purely because it requires little to no additional config on the remote server, just install nagios-plugins, create the nagios user and add the SSH key, all of which I've automated into a shell script. I've never actually considered the performance implications of using SSH over NRPE. I'm not too bothered about the load hit on the Nagios server (It's probably over-speced for what it does, it's never been over 10% CPU), but we run each remote check every 30 seconds and each server has 5 different checks performed. I assume SSH requires more resources for each check but is there a huge difference? (I.E. enough of a difference to warrant the switch to NRPE). If it's any help, we monitor a mix of physical servers (Normally with 8, 12 or 16 physical cores) and Amazon EC2 medium/large instances.

    Read the article

  • Why isn't VIM storing macros across sessions?

    - by dotancohen
    In VIM 7.3 on Ubuntu Server 12.04.1, VIM forgets macros and registers after closing. I do have set nocompatible in .vimrc and the command :set viminfo? gives this result: viminfo='100,<50,s10,h What might be preventing the macros and registers from being stored across close / open? Note that I am not interested in storing mappings for long term use in .vimrc. Rather, sometimes (such as during refactoring) I need to perform a simple operation on a few files and I find it easier to do in VIM than with Perl. I just need the macros and registers stored across open / close, which I do have working on other servers. Thanks.

    Read the article

  • afp/smb transfers caps at 2 megabytes/sec, wireless N

    - by RD.
    I wanted to transfer files between two mac computers. The network is wireless-N and both computers have wireless-N modules in them. The problem is that when I transfer files between them, via file sharing (afp) the network speed caps at 2 megabytes/sec. Just downloading files from the internet I can get faster speeds, so this isn't a constriction of my wifi bandwidth, it appears to be a constriction of the protocol being used. My wifi-n is set to 130mbits, so I should see real world transfer speeds around 12-16 megabytes/sec I did this command on both computers sudo sysctl -w net.inet.tcp.delayed_ack=0 which is supposed to lower tcp overhead, but this did not affect it. How can I get the speed I am expecting?

    Read the article

  • How to copy symbolic links?

    - by Basilevs
    I have directory that contains some symbolic links: user@host:include$ find .. -type l -ls 4737414 0 lrwxrwxrwx 1 user group 13 Dec 9 13:47 ../k0607-lsi6/camac -> ../../include 4737415 0 lrwxrwxrwx 1 user group 14 Dec 9 13:49 ../k0607-lsi6/linux -> ../../../linux 4737417 0 lrwxrwxrwx 1 user group 12 Dec 9 13:57 ../k0607-lsi6/dfc -> ../../../dfc 4737419 0 lrwxrwxrwx 1 user group 17 Dec 9 13:57 ../k0607-lsi6/dfcommon -> ../../../dfcommon 4737420 0 lrwxrwxrwx 1 user group 19 Dec 9 13:57 ../k0607-lsi6/dfcommonxx -> ../../../dfcommonxx 4737421 0 lrwxrwxrwx 1 user group 17 Dec 9 13:57 ../k0607-lsi6/dfcompat -> ../../../dfcompat I need to copy them to the current directory. The resulting links should be independent from their prototypes and lead directly to their target objects. cp -s creates links to links that is not appropriate behavior. cp -s -L refuses to copy links to directories cp -s -L -r refuses to copy relative links to non-working directory What should I do?

    Read the article

  • Who should own exim4 under debian?

    - by raindog308
    Installed debian from DVD. And now I see exim4 is running owned by UID 107. There is no user 107 in my /etc/passwd. Same problem on another system (owned by UID 101), so I suspect this is a debian problem...? Running squeeze on both. So under debian, who should own the mail system? This is what I have installed: # dpkg -l | grep exim ii exim4 4.72-6+squeeze2 metapackage to ease Exim MTA (v4) installation ii exim4-base 4.72-6+squeeze2 support files for all Exim MTA (v4) packages ii exim4-config 4.72-6+squeeze2 configuration for the Exim MTA (v4) ii exim4-daemon-light 4.72-6+squeeze2 lightweight Exim MTA (v4) daemon The binary itself is owned by root: -rwsr-xr-x 1 root root 758852 May 12 2011 /usr/sbin/exim4

    Read the article

  • Can I fine-tune my screen brightness? (Ubuntu Studio, Thinkpad T420s)

    - by Dan S
    I am in a similar situation as question Can I fine-tune my screen brightness? . For me, Thinkpad T420s and Ubuntu Studio 11.10. The brightness keys work fine but the increments are too large. I have the /sys/class/backlight/acpi_video0 and I can see the value of actual_brightness changing as I use the brightness keys - it changes between values 0,3,6,9,12,15. None of the listed answers for fine control works here, as follows: As the root user I can echo integers to brightness in the above folder. As an ordinary user I cannot. I do not have /usr/sbin/gnome-power-backlight-helper (because I'm using xfce perhaps?), and not sure what package it's from or if installing such a package would make sense since it's not what's currently managing the backlight. How can it be done, please?

    Read the article

  • file copy error from system to cifs mount

    - by dwpriest
    When coping a file greater than 64kB from an Ubuntu server to a CIFS mounted windows share, most of the data is copied, but it seems the last chunk doesn't get copied. The size doesn't match, and the md5 check sums don't match. I have plenty of file space, but then I use cp, I get the following... cp: closing `cloudBackup/asdf.txt': No space left on device Using rsync, I get the following... rsync: close failed on "/home/fluffy/cloudBackup/.asdf.txt.qrBWe6": No space left on device (28) rsync error: error in file IO (code 11) at receiver.c(752) [receiver=3.0.8] rsync: connection unexpectedly closed (29 bytes received so far) [sender] rsync error: error in rsync protocol data stream (code 12) at io.c(601) [sender=3.0.8] I have full read/write permissions on the mounted share. I can copy via SSH just fine. Any ideas? Thank you

    Read the article

  • Am I using too much memory? (Rails on EC2 with Resque)

    - by Stpn
    I am looking at the memory usage of the Rails application (it uses background processes via Resque) and since the common answer to the question, "how many workers is too many" was "test and see", I ran some memory commands and wonder if someone can help figuring if the memory usage is high enough already, or I can still add some extra workers.. so (this is all under the maximum load): $ free -t -m total used free shared buffers cached Mem: 1756 1532 223 0 12 229 -/+ buffers/cache: 1291 464 Swap: 895 10 885 Total: 2652 1543 1108 $ vmstat procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 0 0 10588 156172 13400 326476 1 6 4 0 5 4 1 0 99 0 If there is any extra info I can provide to help answer this, I would be happy to do so. If the question is strange in some way, please let me know I'd be glad to fix etc..

    Read the article

  • Xen DomU does not have network connectivity

    - by Prakashkumar Thiagarajan
    I am trying to install Xen on my Fedora box. Dom0 image has network connectivity. But when I try to create a DomU, it does not have network connectivity. I want to be able to run in bridged mode. I have the /etc/xend/xend-config.sxp file accordingly. My config file looks like kernel = "/boot/vmlinuz-2.6.18-xenU" memory = 64 name = "clientA" vif = ['bridge=xenbr0,mac=12.34.56.78.9A.BC'] root = "/dev/sda1 ro" ramdisk = "/boot/initrd-linux.img" extra = "ro selinux=0.3 initcall_debug" features = 'auto_translated_physmap' Am I missing something ?

    Read the article

  • Motherboard: Intel S5520HCR s1366 SSI EEB

    - by Crazy_Bash
    I'm building a storage server for online video streaming. I thought about adding two SSD drive for a OS. other 15*(12 SATA & 3 SSD) drives i want to build with aufs XFS and ethernet 4GB/sec network. But I'm confused a little. S5520HCR board supports 6, SATA/300, RAID: 0, 1, 10, Intel ICH10R. Does it mean i can use SATAIII HDD? I'm planing on buying SEAGATE SV35 Series (3.5, 3??, 64??, SATA III-600). also my Chassis supports up-to 16 sata and the motherboard only 6 what kind of sata controller should i use? What's better in terms of performance 1366 or 2011 socket? My server so far: AIC RSC-3EG-80R-SA1S-2 3U Motherboard: Intel S5520HCR s1366 SSI EEB Kingston DDR3 8192Mb PC3-10600 1333MHz (KVR1333D3N9/8G) Seagate 3000GB 64MB 3.5" 7200rpm SATAIII (ST3000DM001) Kingston 480GB SSD 2.5" SATAIII Intel E1G44HTBLK Intel Xeon E5606 2133MHz/L3-8192Kb/QPI s1366 tray SERVER ACC CARD SAS PCIE 16P HBA 9201-16I LSI00244 SGL LSI

    Read the article

  • How to find what is causing Windows 7 Desktop pause

    - by user1009073
    Windows 7 64 bit. Been in use approx 2 years since last rebuild. Recently, system is misbehaving. Specifically, on bootup, I get the login screen. I login, I get my desktop wallpapers (2 monitors). I get one widget (Rainlender2). It now pauses for approx 12 minutes. After that time, it continues fine, without errors/popups. It acts like the delay never happens. How do I identify the cause of the delay?

    Read the article

  • Copy-paste stops working on Windows 7

    - by earlyadopter
    Copy-paste functionality stops working after about an hour after each reboot on a Windows 7 64-bit system. Running Google Chrome (with gmail and few other tabs open like Calendar, Reader), MS Outlook (which I don't think has anything to do with the problem — I saw it when outlook was off as well), iTunes (9.1.1.12 if it matters). Would appreciate hints where and what for to look in a registry, and ideas for possible fix. That is not an Internet Explorer problem (I don't even run it) — it happens in all applications. Neither Ctrl-C/Ctrl-V nor context menu right-click Copy-Paste (actually, nothing happens on Copy, so there is nothing in a clipboard to Paste) are working. Drag-and-Drop (where supported) continues working though.

    Read the article

  • Replace files with symlink

    - by soandos
    This question is intended to be the inverse of Replace Symbolic Links with Files, but for windows. I have started running out of space on my SSD drive, and I found that about 12% of used space is in my installer folder (holds the .msi files for all the programs that I have installed) I am looking for two things: A way to move this (or any) folder via symlink. Ideally, some powershell function that I could use to just designate a folder, a destination, and the symlink would be created in the original (pointing to the destination) In this particular case, a registry change that would allow the location to be move would also be helpful, but I would still prefer solution 1. How can this be done?

    Read the article

  • Ubuntu: nautilus cannot browse samba shares

    - by Alexey Pilipchuk
    Got a problem with browsing samba shares with nautilus in ubuntu i can see workgroups but cannot go any deeper. On the other hand i can use smbclient and mount samba shares from command line. Also i can browse ubuntu shares from windows but not vise versa. So i suspect it is nautilus problem. Moreover it has never been working for me since very first ubuntu i used. Systems i tryed to browse shares on: Ubuntu 8-12 Windows Xp 7 Dune HD Max Could someone provide me with ideas how to diagnose this issue? Or describe how network browsing is implemented in nautilus Thanx in advance

    Read the article

  • Multi domain server with dedicated SSL's HA

    - by user3692800
    I am hosting a server with 150 domain names (websites), each of the ssl's requere dedicated IP address. So server windows 2008, with 150 IP addressees and 150 websites. I need to have high availability solution. So thinking setting up AWS but ELB will not be a solution... and max IP's I can get per instance is 12 addresses. So what can I do to have all 150 sites hosted on one instance and be HA with instance in different availability zone.

    Read the article

  • RAID 1 after install and two controlers

    - by jfreak53
    I have question regarding RAID 1. Can I setup software RAID 1 after having installed the first drive and setup ubuntu 12? I know that during server install and partitioning I can select RAID and setup then, but what I am not clear on is how in the world to setup RAID 1 after the fact? Can someone provide directions for this? Also, can I RAID 1 two drives one being 500GB and the mirror drive being 1TB? Of course the mirror drive would have a 500GB partition but that's my point. Lastly, can one drive be on IDE and the other on a SATA controller? I know speed will be an issue, that doesn't matter, I just need to know if it will work without corrupting data and if it's the same process? Thanks.

    Read the article

  • COUNTIFS over multiple worksheets

    - by Alison
    I am trying to make COUNTIFS go across two worksheets in the same excel file (Final Driver Forecast Model), just on different tabs. I need it to count if a driver returns between a certain time, then to put a 1 in that time slot. For example if a driver returns at 2:30 p.m. on the 27th, then the formula will put in a 1 in the July 27th slot from 2:00 p.m.-4:00 p.m. I have tried two different formulas the first is =COUNTIF3D(Bid Sheet '[1]Bid Sheet 1'!O4:O110,">="&B76,O4:O110,"<="&C76) This is looking at the worksheet called Bid Sheet 1 and the column O4 through O110 and deciding if the time fits in the time slot of B76 00:00 (12 a.m.) and C 76 2:00 a.m. The second formula I tried to do the exact same thing =COUNTIF3D(O4:O110,">="B76,O4:O110,"<="&C76,"FinalDriverForecastModel',Bid Sheet 1") Neither is working and they both give me #NAME? when I hit enter......What am I doing wrong?

    Read the article

  • How (much) is virtualization used today?

    - by BLAKE
    I know that where I have worked, I have pushed alot for virtualizing our servers. I think that it is much easier to implement and maintain than physical servers. I have been using Microsoft's Virtual Server 2005 R2 since it was released. Right now at my workplace we have 12 VMHosts that hold about 55 VMs. We have 6 other servers that we have been unable to convert to VMs. I want to know how other people in our field view virtualization. I know that I have had developers dislike the notion of VMs claiming major performance hits. What do other Sys Admins think about virtualized servers?

    Read the article

  • Odd SVN Checkout failures occur frequenctly on VMWare virtual machines

    - by snowballhg
    We've recently been experiencing seemingly random SVN checkout failures on our Hudson build system. Google search has failed me; I'm hoping the super user community can help me out :-) We are occasionally receiving the following SVN error when our Hudson build jobs checkout source via the Hudson Subversion plug-in (which uses svn kit): ERROR: Failed to check out http://server/svnroot/trunk org.tmatesoft.svn.core.SVNException: svn: Processing REPORT request response failed: XML document structures must start and end within the same entity. (/svnroot/!svn/vcc/default) svn: REPORT request failed on '/svnroot/!svn/vcc/default' This issue seems to only occur when checking out from our Virtual Machines (Windows XP, Fedora 9, Fedora 12) using Hudson's SVN Plug-in. Systems that use the traditional SVN client seem to work. SVN Server version: 1.6.6 Hudson version: 1.377 Hudson SVN Plugin Version: 1.17 Has anyone dealt with this issue, or have any suggestions? Thanks

    Read the article

  • Unable to change IP address for eth0 without restart in Ubuntu

    - by Rodnower
    I have Ubuntu 12.04.1 installed. I tried to change the IP address of the interface eth0 in /etc/network/interfaces from 192.168.1.3 to 192.168.1.4 auto lo iface lo inet loopback pre-up iptables-restore < /etc/iptables.up.rules auto eth0 iface eth0 inet static address 192.168.1.4 gateway 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 sudo service networking status When I issue: sudo service networking restart I get this response: stop: Unknown instance: networking stop/waiting And IP remains 192.168.1.3: eth0 Link encap:Ethernet HWaddr 00:1e:33:71:cd:a4 inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21e:33ff:fe71:cda4/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3861 errors:0 dropped:0 overruns:0 frame:0 TX packets:3291 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3423285 (3.4 MB) TX bytes:521854 (521.8 KB) Interrupt:45 Base address:0x4000 Only after restart does the IP change. Any ideas?

    Read the article

  • Creating ip alias on bonded interface ie. bond0:1

    - by bobothechimp
    System: HP Proliant DL360 G5 running CentOS 5.4 Bonded interface is working fine for a long time. I just went to add an alias the way I always have on a regular interface, and on first check it works (pinging on the local box) but it is not accessable from outside (iptables is turned off). In addition with this setup the normal network response started to decline, hanging for around a minute before I could get a prompt on login. Here are my config files: [root network-scripts]# cat ifcfg-eth0 DEVICE=eth0 BOOTPROTO=none ONBOOT=yes MASTER=bond0 SLAVE=yes USERCTL=no [root network-scripts]# cat ifcfg-eth1 DEVICE=eth1 BOOTPROTO=none ONBOOT=yes MASTER=bond0 SLAVE=yes USERCTL=no [root network-scripts]# cat ifcfg-bond0 DEVICE=bond0 BONDING_OPTS="mode=1 miimon=100" BOOTPROTO=none ONBOOT=yes NETWORK=10.2.1.0 NETMASK=255.255.255.0 IPADDR=10.2.1.11 USERCTL=no [root network-scripts]# cat ifcfg-bond0:1 DEVICE=bond0:1 BOOTPROTO=static ONBOOT=yes NETWORK=10.2.1.0 NETMASK=255.255.255.0 IPADDR=10.2.1.12 USERCTL=no any thoughts?

    Read the article

  • Linux/Apache performance very slow even on local network

    - by klausch
    I have an Ubuntu server machine running Apache and MYSQL. System and version info is as follows: Linux kernel 3.0.0.-12 Apache/2.2.20 MySQL Ver 14.14.Distrib 5.1.58 I am running a few websites on this server, some HTML only, some PHP/MySQL. THe [problem is that response time is very slow, both on static as well as the dynamic sites. Sometimes it takes more than 10 seconds before a response is given, this makes the sites very slow and almost unusable. The problem occurs even when requesting from the local network. I have added the involved subdomains to my /etc/hosts file, and abolve all the problem is not solved by using IP numbers instead of URL's. So there is no DNS lookup issue. I have modified the log format by showing the response times and sometimes a files takes 12 seconds to be served, see the jquery~.js file in the example screenshot. I have no explanation for this extremely long response time, but is is not even the only issue here, some other files takes a long time to be served too, but do not show a long response time in the log file. So probably different tissues are involved here. I cannot find a solution until now, any suggestions??? THanx in advance, Klaas link to screenshot picture from access logfile Some extra configuration info: apache2.conf (comment is removed) LockFile ${APACHE_LOCK_DIR}/accept.lock PidFile ${APACHE_PID_FILE} Timeout 300 KeepAlive On MaxKeepAliveRequests 100 KeepAliveTimeout 5 <IfModule mpm_prefork_module> StartServers 5 MinSpareServers 5 MaxSpareServers 10 MaxClients 150 MaxRequestsPerChild 0 </IfModule> <IfModule mpm_worker_module> StartServers 2 MinSpareThreads 25 MaxSpareThreads 75 ThreadLimit 64 ThreadsPerChild 25 MaxClients 150 MaxRequestsPerChild 0 </IfModule> <IfModule mpm_event_module> StartServers 2 MinSpareThreads 25 MaxSpareThreads 75 ThreadLimit 64 ThreadsPerChild 25 MaxClients 150 MaxRequestsPerChild 0 </IfModule> User ${APACHE_RUN_USER} Group ${APACHE_RUN_GROUP} AccessFileName .htaccess <Files ~ "^\.ht"> Order allow,deny Deny from all Satisfy all </Files> DefaultType text/plain HostnameLookups Off ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel warn Include mods-enabled/*.load Include mods-enabled/*.conf Include httpd.conf Include ports.conf LogFormat "%v:%p %h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" vhost_combined LogFormat "%h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\" %T/%D" combined LogFormat "%h %l %u %t \"%r\" %>s %O" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent Include conf.d/ Include sites-enabled/ And the virtual hostfile for one of the slow sites, in fact it is pretty straightforward... <VirtualHost *:80> ServerAdmin [email protected] ServerSignature EMail ServerName toenjoy.drsklaus.nl DocumentRoot /var/www/toenjoy.drsklaus.nl <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/toenjoy.drsklaus.nl/> Options Indexes FollowSymLinks MultiViews AllowOverride AuthConfig AuthType Basic AuthName "To Enjoy" AuthUserFile /etc/.htpasswd Require user petraaa Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> And the output of free -m: klaas@ubuntu-server:/etc/apache2$ free -m total used free shared buffers cached Mem: 1997 1401 595 0 144 1017 -/+ buffers/cache: 238 1758 Swap: 2035 0 2035 and I have no indication that swapping occurs on the moments the site is slow. I have runned top and it does not appear to be a CPU issue. I have the impression that the spawning of a apache thread could maybe be the bottleneck but it is just a suggestion. Maybe this gives some extra information! EDIT: The problem seemed to be gone for some time but occurs again! And not only with Apache, also connecting using SSH takes a tremendous time, sometimes it takes up to 15 seconds before the keyphrase is asked for. Also scp works very slowly. The behavious is really unpredoctable and makes the server very hard to use. Any ideas...?

    Read the article

  • Where can I find a good, tab-less privacy filter for my monitor?

    - by KeyStroke
    Hi, I have an ASUS laptop with a 14" monitor (12" by 7" to be more specific), and I've been looking for a decent privacy filter that I can use with for, yet I couldn't find any. The problem with the filters I've found is that they all use those ugly "tabs" that you have to stick on the sides of your monitor in order to slip the filter in. I'm looking for ones that are like HP privacy filter, where parts of it goes under the frame of the monitor to hold it in place. Too bad HP doesn't sell filters that fit my screen. So, any idea where I can get a good privacy filter? Your help is so much appreciated

    Read the article

  • how to debug BSOD irql_not_less_or_equal error

    - by Sev
    So I'm getting the irql_not_less_or_equal BSOD. I tried looking at the event viewer for potential causes, and cannot find any. I also checked the CPU temperature in BIOS right after the error and that was fine. I've tried 2 sets of RAM chips already, both give the issues. The error doesn't happen consistently...it happens daily, but many hours can pass and it won't happen, or only 10 minutes can pass and it might happen again. By the way, just bought the parts and built the computer myself a couple of weeks ago. How to debug the cause for this? Hardware info: Asus P6X58D PREMIUM motherboard Intel core i7 930 quad core 2.8 ghz Kingston 128 GB SSD 3 Gb/sec Nvidia Geforce GTX 465 PNY Edition Corsair 12 GB DDR3 1600 Mhz Ram Windows 7 Ultimate

    Read the article

< Previous Page | 224 225 226 227 228 229 230 231 232 233 234 235  | Next Page >