Search Results

Search found 6651 results on 267 pages for 'description'.

Page 229/267 | < Previous Page | 225 226 227 228 229 230 231 232 233 234 235 236  | Next Page >

• Sound issues after trying everything

  - by Lerp

  I cannot get my sound working properly, no matter what I do, there's always some problem. It's very annoying as it's the only thing preventing me from making Ubuntu my main OS. At the moment my sound always plays through both my speakers and my headphones regardless except the sound through the headphones is crackly. It is also a bit quiet even though everything is maxed. I've managed to improve the situation to a point where the sound out of my speakers is perfect but I have none at all from my headphones. I do have two connectors listed in the sound settings but regardless of which one is selected it always plays through the speakers. I think this might have something to do with the fact that my speakers are plugging into the front of my computer, typically the headphone jack, and my headphones are plugging into the back but when I try disconnecting the speakers from the front there is still no sound from the headphones. I fixed the speaker sound by going through the sound settings and making sure they were all set to 100% then rebooting. Things I have tried: Maxing everything and unmuting everything in alsamixer Uninstalling pulseaudio Making gstreamer use only alsa via gstreamer-properties. This worked with the sound test button including independent sound between headphones and speakers but when I reset the computer it no longer worked. So I tried setting it manually in gconf-editor which didn't work either. Reinstalling alsa and pulseaudio Setting the model in /etc/modprobe.d/alsa-base.conf to 6stack and 6stack-dig neither worked. Upgrading to 12.10 Here's some command output to help you diagnose my problem. aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Intel [HDA Intel], device 0: AD198x Analog [AD198x Analog] Subdevices: 0/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 1: AD198x Digital [AD198x Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 2: AD198x Headphone [AD198x Headphone] Subdevices: 1/1 Subdevice #0: subdevice #0 sudo lshw -C sound *-multimedia description: Audio device product: 82801JI (ICH10 Family) HD Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:70 memory:f7ff8000-f7ffbfff cat /proc/asound/card*/codec* | grep "Codec" Codec: Analog Devices AD1989B cat /etc/modprobe.d/alsa-base.conf # autoloader aliases install sound-slot-0 /sbin/modprobe snd-card-0 install sound-slot-1 /sbin/modprobe snd-card-1 install sound-slot-2 /sbin/modprobe snd-card-2 install sound-slot-3 /sbin/modprobe snd-card-3 install sound-slot-4 /sbin/modprobe snd-card-4 install sound-slot-5 /sbin/modprobe snd-card-5 install sound-slot-6 /sbin/modprobe snd-card-6 install sound-slot-7 /sbin/modprobe snd-card-7 # Cause optional modules to be loaded above generic modules install snd /sbin/modprobe --ignore-install snd $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-ioctl32 ; /sbin/modprobe --quiet --use-blacklist snd-seq ; } # # Workaround at bug #499695 (reverted in Ubuntu see LP #319505) install snd-pcm /sbin/modprobe --ignore-install snd-pcm $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-pcm-oss ; : ; } install snd-mixer /sbin/modprobe --ignore-install snd-mixer $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-mixer-oss ; : ; } install snd-seq /sbin/modprobe --ignore-install snd-seq $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-seq-midi ; /sbin/modprobe --quiet --use-blacklist snd-seq-oss ; : ; } # install snd-rawmidi /sbin/modprobe --ignore-install snd-rawmidi $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-seq-midi ; : ; } # Cause optional modules to be loaded above sound card driver modules install snd-emu10k1 /sbin/modprobe --ignore-install snd-emu10k1 $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-emu10k1-synth ; } install snd-via82xx /sbin/modprobe --ignore-install snd-via82xx $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-seq ; } # Load saa7134-alsa instead of saa7134 (which gets dragged in by it anyway) install saa7134 /sbin/modprobe --ignore-install saa7134 $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist saa7134-alsa ; : ; } # Prevent abnormal drivers from grabbing index 0 options bt87x index=-2 options cx88_alsa index=-2 options saa7134-alsa index=-2 options snd-atiixp-modem index=-2 options snd-intel8x0m index=-2 options snd-via82xx-modem index=-2 options snd-usb-audio index=-2 options snd-usb-caiaq index=-2 options snd-usb-ua101 index=-2 options snd-usb-us122l index=-2 options snd-usb-usx2y index=-2 # Ubuntu #62691, enable MPU for snd-cmipci options snd-cmipci mpu_port=0x330 fm_port=0x388 # Keep snd-pcsp from being loaded as first soundcard options snd-pcsp index=-2 # Keep snd-usb-audio from beeing loaded as first soundcard options snd-usb-audio index=-2 options snd-hda-intel model=6stack

  Read the article

• HP Pavilion tx2000 - Wifi adapter no longer works after moving from 12.04 to a 12.10 clean install

  - by Marek L.

  I have a HP Pavilion tx2000 that I have been running Ubuntu 12.04 on for a couple of months without any problems (wifi worked great) until yesterday when my hard drive failed. I replaced the hard drive and decided to install Ubuntu 12.10. Unlike 12.04, the wifi did not work after the installation finished and all the updates where installed (over Ethernet). The network drop down in the top right didn't even show a wireless option. I Googled about for a bit and found some solutions that seemed like they might work. Unfortunately they did not. Here is what I tried: sudo apt-get remove bcmwl-kernel-source sudo apt-get install b43-fwcutter sudo apt-get install firmware-b43-lpphy-installer Restart the computer. And the wifi still didn't work. At which point I panicked a bit and tried to undo the previous commands by running: sudo apt-get remove b43-fwcutter firmware-b43-lpphy-installer sudo apt-get install bcmwl-kernel-source Restart the computer. The wifi still doesn't work. This is where I stopped because I have no idea what I am doing and don't want to mess something up. The network drop down still doesn't show a wireless option and the hardware wifi switch on the laptop is amber (it turns blue when the wifi is on). Using the hardware switch does not change the color. Output from: sudo lspci ... 08:00.0 Network controller: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller (rev 01) ... Output from: sudo lshw -class network *-network UNCLAIMED description: Network controller product: BCM4322 802.11a/b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:08:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:d1100000-d1103fff ... Output from: sudo rfkill list all 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes UPDATE: After writing up this question tried the following command: sudo rfkill unblock all At first it didn't do anything but after running it about four times, sudo rfkill list all now returns: 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no But the network menu still does not have a wireless option and the hardware switch still glows amber. Pushing the hardware switch turns the hard block back on and I have to run sudo rfkill unblock all multiple times again to turn it off. Any help is appreciated! Update 2: Full output from sudo lspci -nn: 00:00.0 Host bridge [0600]: Advanced Micro Devices [AMD] RS780 Host Bridge [1022:9600] 00:01.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (int gfx) [1022:9602] 00:04.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 0) [1022:9604] 00:05.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 1) [1022:9605] 00:06.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) [1022:9606] 00:11.0 SATA controller [0106]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] [1002:4391] 00:12.0 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397] 00:12.1 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0 USB OHCI1 Controller [1002:4398] 00:12.2 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396] 00:13.0 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397] 00:13.1 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0 USB OHCI1 Controller [1002:4398] 00:13.2 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396] 00:14.0 SMBus [0c05]: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller [1002:4385] (rev 3a) 00:14.1 IDE interface [0101]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 IDE Controller [1002:439c] 00:14.2 Audio device [0403]: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) [1002:4383] 00:14.3 ISA bridge [0601]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 LPC host controller [1002:439d] 00:14.4 PCI bridge [0604]: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge [1002:4384] 00:14.5 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI2 Controller [1002:4399] 00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor HyperTransport Configuration [1022:1300] (rev 40) 00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor Address Map [1022:1301] 00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor DRAM Controller [1022:1302] 00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor Miscellaneous Control [1022:1303] 00:18.4 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor Link Control [1022:1304] 01:05.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI RS780M/RS780MN [Mobility Radeon HD 3200 Graphics] [1002:9612] 08:00.0 Network controller [0280]: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller [14e4:432b] (rev 01) 09:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 02)

  Read the article

• Working with packed dates in SSIS

  - by Jim Giercyk

  One of the challenges recently thrown my way was to read an EBCDIC flat file, decode packed dates, and insert the dates into a SQL table.  For those unfamiliar with packed data, it is a way to store data at the nibble level (half a byte), and was often used by mainframe programmers to conserve storage space.  In the case of my input file, the dates were 2 bytes long and  represented the number of days that have past since 01/01/1950.  My first thought was, in the words of Scooby, Hmmmmph?  But, I love a good challenge, so I dove in. Reading in the flat file was rather simple.  The only difference between reading an EBCDIC and an ASCII file is the Code Page option in the connection manager.  In my case, I needed to use Code Page 1140 for EBCDIC (I could have also used Code Page 37).       Once the code page is set correctly, SSIS can understand what it is reading and it will convert the output to the default code page, 1252.  However, packed data is either unreadable or produces non-alphabetic characters, as we can see in the preview window.   Column 1 is actually the packed date, columns 0 and 2 are the values in the rest of the file.  We are only interested in Column 1, which is a 2 byte field representing a packed date.  We know that 2 bytes of packed data can be stored in 1 byte of character data, so we are working with 4 packed digits in 2 character bytes.  If you are confused, stay tuned….this will make sense in a minute.   Right-click on your Flat File Source shape and select “Show Advanced Editor”. Here is where the magic begins. By changing the properties of the output columns, we can access the packed digits from each byte. By default, the Output Column data type is DT_STR. Since we want to look at the bytes individually and not the entire string, change the data type to DT_BYTES. Next, and most important, set UseBinaryFormat to TRUE. This will write the HEX VALUES of the output string instead of writing the character values.  Now we are getting somewhere! Next, you will need to use a Data Conversion shape in your Data Flow to transform the 2 position byte stream to a 4 position Unicode string containing the packed data.  You need the string to be 4 bytes long because it will contain the 4 packed digits.  Here is what that should look like in the Data Conversion shape: Direct the output of your data flow to a test table or file to see the results.  In my case, I created a test table.  The results looked like this:     Hold on a second!  That doesn't look like a date at all.  No, of course not.  It is a hex number which represents the days which have passed between 01/01/1950 and the date.  We have to convert the Hex value to a decimal value, and use the DATEADD function to get a date value.  Luckily, I have created a function to convert Hex to Decimal:   -- ============================================= -- Author:        Jim Giercyk -- Create date: March, 2012 -- Description:    Converts a Hex string to a decimal value -- ============================================= CREATE FUNCTION [dbo].[ftn_HexToDec] (     @hexValue NVARCHAR(6) ) RETURNS DECIMAL AS BEGIN     -- Declare the return variable here DECLARE @decValue DECIMAL IF @hexValue LIKE '0x%' SET @hexValue = SUBSTRING(@hexValue,3,4) DECLARE @decTab TABLE ( decPos1 VARCHAR(2), decPos2 VARCHAR(2), decPos3 VARCHAR(2), decPos4 VARCHAR(2) ) DECLARE @pos1 VARCHAR(1) = SUBSTRING(@hexValue,1,1) DECLARE @pos2 VARCHAR(1) = SUBSTRING(@hexValue,2,1) DECLARE @pos3 VARCHAR(1) = SUBSTRING(@hexValue,3,1) DECLARE @pos4 VARCHAR(1) = SUBSTRING(@hexValue,4,1) INSERT @decTab VALUES (CASE               WHEN @pos1 = 'A' THEN '10'                 WHEN @pos1 = 'B' THEN '11'               WHEN @pos1 = 'C' THEN '12'               WHEN @pos1 = 'D' THEN '13'               WHEN @pos1 = 'E' THEN '14'               WHEN @pos1 = 'F' THEN '15'               ELSE @pos1              END, CASE               WHEN @pos2 = 'A' THEN '10'                 WHEN @pos2 = 'B' THEN '11'               WHEN @pos2 = 'C' THEN '12'               WHEN @pos2 = 'D' THEN '13'               WHEN @pos2 = 'E' THEN '14'               WHEN @pos2 = 'F' THEN '15'               ELSE @pos2              END, CASE               WHEN @pos3 = 'A' THEN '10'                 WHEN @pos3 = 'B' THEN '11'               WHEN @pos3 = 'C' THEN '12'               WHEN @pos3 = 'D' THEN '13'               WHEN @pos3 = 'E' THEN '14'               WHEN @pos3 = 'F' THEN '15'               ELSE @pos3              END, CASE               WHEN @pos4 = 'A' THEN '10'                 WHEN @pos4 = 'B' THEN '11'               WHEN @pos4 = 'C' THEN '12'               WHEN @pos4 = 'D' THEN '13'               WHEN @pos4 = 'E' THEN '14'               WHEN @pos4 = 'F' THEN '15'               ELSE @pos4              END) SET @decValue = (CONVERT(INT,(SELECT decPos4 FROM @decTab)))         +                 (CONVERT(INT,(SELECT decPos3 FROM @decTab))*16)      +                 (CONVERT(INT,(SELECT decPos2 FROM @decTab))*(16*16)) +                 (CONVERT(INT,(SELECT decPos1 FROM @decTab))*(16*16*16))     RETURN @decValue END GO     Making use of the function, I found the decimal conversion, added that number of days to 01/01/1950 and FINALLY arrived at my “unpacked relative date”.  Here is the query I used to retrieve the formatted date, and the result set which was returned: SELECT [packedDate] AS 'Hex Value',        dbo.ftn_HexToDec([packedDate]) AS 'Decimal Value',        CONVERT(DATE,DATEADD(day,dbo.ftn_HexToDec([packedDate]),'01/01/1950'),101) AS 'Relative String Date'   FROM [dbo].[Output Table]         This technique can be used any time you need to retrieve the hex value of a character string in SSIS.  The date example may be a bit difficult to understand at first, but with SSIS becoming the preferred tool for enterprise level integration for many companies, there is no doubt that developers will encounter these types of requirements with regularity in the future. Please feel free to contact me if you have any questions.

  Read the article

• WebLogic JDBC Use of Oracle Wallet for SSL

  - by Steve Felts

  Introduction Secure Sockets Layer (SSL) can be used to secure the connection between the middle tier “client”, WebLogic Server (WLS) in this case, and the Oracle database server.  Data between WLS and database can be encrypted.  The server can be authenticated so you have proof that the database can be trusted by validating a certificate from the server.  The client can be authenticated so that the database only accepts connections from clients that it trusts. Similar to the discussion in an earlier article about using the Oracle wallet for database credentials, the Oracle wallet can also be used with SSL to store the keys and certificates.  By using it correctly, clear text passwords can be eliminated from the JDBC configuration and client/server configuration can be simplified by sharing the wallet across multiple datasources. There is a very good Oracle Technical White Paper on using SSL with the Oracle thin driver at http://www.oracle.com/technetwork/database/enterprise-edition/wp-oracle-jdbc-thin-ssl-130128.pdf [LINK1].  The link http://www.oracle.com/technetwork/middleware/weblogic/index-087556.html [LINK2] describes how to use WebLogic Server with Oracle JDBC Driver SSL. The information in this article is a guide on what steps need to be taken in the variety of available options; use the links above for details. SSL from the driver to the database server is basically turned on by specifying a protocol of “tcps” in the URL.  However, there is a fair amount of setup needed.  Also remember that there is an overhead in performance. Creating the wallets The common use cases are 1. “data encryption and server-only authentication”, requiring just a trust store, or 2. “data encryption and authentication of both tiers” (client and server), requiring a trust store and a key store. It is recommended to use the auto-login wallet type so that clear text passwords are not needed in the datasource configuration to open the wallet.  The store type for an auto-login wallet is “SSO” (Single Sign On), not “JKS” or “PKCS12” as in [LINK2].  The file name is “cwallet.sso”. Wallets are created using the orapki tool.  They need to be created based on the usage (encryption and/or authentication).  This is discussed in detail in [LINK1] in Appendix B or in the Advanced Security Administrator’s Guide of the Database documentation. Database Server Configuration It is necessary to update the sqlnet.ora and listener.ora files with the directory location of the wallet using WALLET_LOCATION.  These files also indicate whether or not SSL_CLIENT_AUTHENTICATION is being used (true or false). The Oracle Listener must also be configured to use the TCPS protocol.  The recommended port is 2484. LISTENER = (ADDRESS_LIST= (ADDRESS=(PROTOCOL=tcps)(HOST=servername)(PORT=2484))) WebLogic Server Classpath The WebLogic Server CLASSPATH must have three additional security files. The files that need to be added to the WLS CLASSPATH are $MW_HOME/modules/com.oracle.osdt_cert_1.0.0.0.jar $MW_HOME/modules/com.oracle.osdt_core_1.0.0.0.jar $MW_HOME/modules/com.oracle.oraclepki_1.0.0.0.jar One way to do this is to add them to PRE_CLASSPATH environment variable for use with the standard WebLogic scripts. Setting the Oracle Security Provider It’s necessary to enable the Oracle PKI provider on the client side.  This can either be done statically by updating the java.security file under the JRE or dynamically by setting it in a WLS startup class using java.security.Security.insertProviderAt(new oracle.security.pki.OraclePKIProvider (), 3); See the full example of the startup class in [LINK2]. Datasource Configuration When creating a WLS datasource, set the PROTOCOL in the URL to tcps as in the following. jdbc:oracle:thin:@(DESCRIPTION=(ADDRESS=(PROTOCOL=tcps)(HOST=host)(PORT=port))(CONNECT_DATA=(SERVICE_NAME=myservice))) For encryption and server authentication, use the datasource connection properties: - javax.net.ssl.trustStore=location of wallet file on the client - javax.net.ssl.trustStoreType=”SSO” For client authentication, use the datasource connection properties: - javax.net.ssl.keyStore=location of wallet file on the client - javax.net.ssl.keyStoreType=”SSO” Note that the driver connection properties for the wallet require a file name, not a directory name. Active GridLink ONS over SSL For completeness, there is another SSL usage for WLS datasources.  The communication with the Oracle Notification Service (ONS) for load balancing information and node up/down events can use SSL also. Create an auto-login wallet and use the wallet on the client and server.  The following is a sample sequence to create a test wallet for use with ONS. orapki wallet create -wallet ons -auto_login -pwd ONS_Wallet orapki wallet add -wallet ons -dn "CN=ons_test,C=US" -keysize 1024 -self_signed -validity 9999 -pwd ONS_Wallet orapki wallet export -wallet ons -dn "CN=ons_test,C=US" -cert ons/cert.txt -pwd ONS_Wallet On the database server side, it’s necessary to define the walletfile directory in the file $CRS_HOME/opmn/conf/ons.config and run onsctl stop/start. When configuring an Active GridLink datasource, the connection to the ONS must be defined.  In addition to the host and port, the wallet file directory must be specified.  By not giving a password, a SSO wallet is assumed. Summary To use SSL with the Oracle thin driver without any clear text passwords, use an SSO Oracle Wallet.  SSL support in the Oracle thin driver is available starting in 10g Release 2.

  Read the article

• Announcing Solaris Technical Track at NLUUG Spring Conference on Operating Systems

  - by user9135656

  The Netherlands Unix Users Group (NLUUG) is hosting a full-day technical Solaris track during its spring 2012 conference. The official announcement page, including registration information can be found at the conference page.This year, the NLUUG spring conference focuses on the base of every computing platform; the Operating System. Hot topics like Cloud Computing and Virtualization; the massive adoption of mobile devices that have their special needs in the OS they run but that at the same time put the challenge of massive scalability onto the internet; the upspring of multi-core and multi-threaded chips..., all these developments cause the Operating System to still be a very interesting area where all kinds of innovations have taken and are taking place.The conference will focus specifically on: Linux, BSD Unix, AIX, Windows and Solaris. The keynote speech will be delivered by John 'maddog' Hall, infamous promotor and supporter of UNIX-based Operating Systems. He will talk the audience through several decades of Operating Systems developments, and share many stories untold so far. To make the conference even more interesting, a variety of talks is offered in 5 parallel tracks, covering new developments in and  also collaboration  between Linux, the BSD's, AIX, Solaris and Windows. The full-day Solaris technical track covers all innovations that have been delivered in Oracle Solaris 11. Deeply technically-skilled presenters will talk on a variety of topics. Each topic will first be introduced at a basic level, enabling visitors to attend to the presentations individually. Attending to the full day will give the audience a comprehensive overview as well as more in-depth understanding of the most important new features in Solaris 11.NLUUG Spring Conference details:* Date and time:        When : April 11 2012        Start: 09:15 (doors open: 8:30)        End  : 17:00, (drinks and snacks served afterwards)* Venue:        Nieuwegein Business Center        Blokhoeve 1             3438 LC Nieuwegein              The Nederlands          Tel     : +31 (0)30 - 602 69 00        Fax     : +31 (0)30 - 602 69 01        Email   : [email protected]        Route   : description - (PDF, Dutch only)* Conference abstracts and speaker info can be found here.* Agenda for the Solaris track: Note: talks will be in English unless marked with 'NL'.1.      Insights to Solaris 11         Joerg Moellenkamp - Solaris Technical Specialist         Oracle Germany2.      Lifecycle management with Oracle Solaris 11         Detlef Drewanz - Solaris Technical Specialist         Oracle Germany3.      Solaris 11 Networking - Crossbow Project        Andrew Gabriel - Solaris Technical Specialist        Oracle UK4.      ZFS: Data Integrity and Security         Darren Moffat - Senior Principal Engineer, Solaris Engineering         Oracle UK5.      Solaris 11 Zones and Immutable Zones (NL)         Casper Dik - Senior Staff Engineer, Software Platforms         Oracle NL6.      Experiencing Solaris 11 (NL)         Patrick Ale - UNIX Technical Specialist         UPC Broadband, NLTalks are 45 minutes each.There will be a "Solaris Meeting point" during the conference where people can meet-up, chat with the speakers and with fellow Solaris enthousiasts, and where live demos or other hands-on experiences can be shared.The official announcement page, including registration information can be found at the conference page on the NLUUG website. This site also has a complete list of all abstracts for all talks.Please register on the NLUUG website.

  Read the article

• BizTalk &ndash; Routing failure on Delivery Notifications (BizTalk 2006 R2 to 2013)

  - by S.E.R.

  Originally posted on: http://geekswithblogs.net/SERivas/archive/2013/11/11/biztalk-routing-failure-on-delivery-notifications.aspxThis is a detailed explanation of a something I posted a few month ago on stackoverflow, concerning a weird behavior (a bug, really…) of the delivery notifications in BizTalk. Reminder: what are delivery notifications Mechanism BizTalk has the ability to automatically publish positive acknowledgments (ACK) when it has succeeded transmitting a message or negative acknowledgments (NACK) in case of a transmission failure. Orchestrations can use delivery notifications to subscribe to those ACKs and NACKs in order to know if a message sent on a one-way send port has been successfully transmitted. Delivery Notifications can be “activated” in two ways: The most common and easy way is to set the Delivery Notification property of a logical send port (in the orchestration designer) to Transmitted: Another way is to set the BTS.AckRequired context property of the message to be sent to true: NOTE: fundamentally, those methods are strictly equivalent since the fact of setting the Delivery Notification to Transmitted on the send port only tells BizTalk the BTS.AckRequired context property has to be set to true on the outgoing message. Related context properties ACKs and NACKs have a common set of propoted context properties, which are : Propriété Description AckType Equals ACK when successful or NACK otherwise AckID MessageID of the message concerned by the acknowledgment AckOwnerID InstanceID of the instance associated with the acknowledgment AckSendPortID ID of the send port AckSendPortName Name of the send port AckOutboundTransportLocation URI of the send port AckReceivePortID ID of the port the message came from AckReceivePortName Name of the port the message came from AckInboundTransportLocation URI of the port the message came from Detailed behavior The way Delivery Notifications are handled by BizTalk is peculiar compared to the standard behavior of the Message Box: if no active subscription exists for the acknowledgment, it is simply discarded. The direct consequence of this is that there can be no routing failure for an acknowledgment, and an acknowledgment cannot be suspended. Moreover, when a message is sent to a send port where Delivery Notification = Transmitted, a correlation set is initialized and a correlation token is attached to the message (Context property: CorrelationToken). This correlation token will also be attached to the acknowledgment. So when the acknowledgment is issued, it is automatically routed to the source orchestration. Finally, when a NACK is received by the source orchestration, a DeliveryFailureException is thrown, which can be caught in Catch section. Context of the problem Consider this scenario: In an orchestration, Delivery Notifications are activated on a One-Way send port In case of a transmission failure, the messaging instance is suspended and the orchestration catches an exception (DeliveryFailureException). When the exception is caught, the orchestration does some logging and then terminates (thanks to a Terminate shape). So that leaves only the suspended messaging instance, waiting to be resumed. Symptoms Once the problem that caused the transmission failure is solved, the messaging instance is resumed. Considering what was said in the reminder, we would expect the instance to complete, leaving no active or suspended instance. Nevertheless, the result is that the messaging instance is once more suspended, this time because of a routing failure: The routing failure report shows that the suspended message has the following attached properties: Explanation Those properties clearly indicate that the message being suspended is an acknowledgment (ACK in this case), which was published in the message box and was supended because no subscribers were found. This makes sense, since the source orchestration was terminated before we resumed the messaging instance. So its subscription to the acknowledgments was no longer active when the ACK was published, which explains the routing failure. But this behavior is in direct contradiction with what was said earlier: an acknowledgment must be discarded when no subscriber is found and therefore should not be suspended. Cause It is indeed an outright bug, which appeared with the SP1 of BizTalk 2006 R2 and was never corrected since then: not in the next 4 CUs, not in BizTalk 2009, not in 2010 and not event in 2013 – though I haven’t tested CU1 and CU2 for this last edition, but I bet there is nothing to be expected from those CUs (on this particular point). Side effects This bug can have pretty nasty side effects: this behavior can be propagated to other ports, due to routing mechanisms. For instance: you have configured the ESB Toolkit and have activated the “Enable routing failure for failed messages”. The result will be that the ESB Exception SQL send port will also try and publish ACKs or NACKs concerning its own messaging instances. In itself, this is already messy, but remember that those acknowledgments will also have the source correlation token attached to them… See how far it goes? Well, actually there is more: in SQL send ports, transactions will be rolled back because of the routing failure (I guess it also happens with other adapters - like Oracle, but I haven’t tested them). Again, think of what happens when the send port is the ESB Exception send port: your BizTalk box is going mad, but you have no idea since no exception can be written in the exception database! All of this can be tricky to diagnose, I can tell you that… Solution There is no real solution, only a work-around, but it won’t solve all of the problems and side effects. The idea is to create an orchestration which subscribes to all acknowledgments. That is to say: The message type of the incoming message will be XmlDocument The BTS.AckType property exists The logical receive port will use direct binding By doing so, all acknowledgments will be consumed by an instance of this orchestration, thus avoiding the routing failure. Here is an example of what this orchestration could look like: In order not to pollute the HAT and the DTA Db (after all, this orchestration is only meant to be a palliative to some faulty internal BizTalk mechanism, so there should be no trace of its execution), all tracking must be deactivated:

  Read the article

• Some New .NET Downloads and Resources

  - by Kevin Grossnicklaus

  Last week I was fortunate enough to spend time in Redmond on Microsoft’s campus for the 2011 Microsoft MVP Summit.  It was great to hang out with a number of old friends and get the opportunity to talk tech with the various product teams up at Microsoft.  The weather wasn’t exactly sunny but Microsoft always does a great job with the Summit and everyone had a blast (heck, I even got to run the bases at SafeCo field) While much of what we saw is covered under NDA, there a ton of great things in the pipeline from Microsoft and many things that are already available (or just became so) that I wasn’t necessarily aware of.  The purpose of this post is to share some of the info I learned on resources and tools available to .NET developers today.  Please let me know if you have any questions (or if you know of something else cool which might benefit others). Enjoy! Visual Studio 2010 SP1 Microsoft has issued the RTM release of Visual Studio 2010 SP1.  You can download the full SP1 on MSDN as of today (March 10th to the general public) and take advantage of such things as: Silverlight 4 is included in the box (as opposed to a separate install) Silverlight 4 Profiling WCF RIA Services SP1 Intellitrace for 64-bit and SharePoint ASP.NET now easily supports IIS Express and SQL CE Want a description of all that’s new beyond the above biased list (which arguably only contains items I think are important)?  Check out this KB article. Portable Library Tools CTP Without much fanfare Microsoft has released a CTP of a new add-in to Visual Studio 2010 which simplifies code sharing between projects targeting different runtimes (i.e. Silverlight, WPF, Win7 Phone, XBox).   With this Add-In installed you can add a new project of type “Portable Library” and specify which platforms you wish to target.  Once that is done, any code added to this library will be limited to use only features which are common to all selected frameworks.  Other projects can now reference this portable library and be provided assemblies custom built to their environment.  This greatly simplifies the current process of sharing linked files between platforms like WPF and Silverlight.  You can find out more about this CTP and how it works on this great blog post. Visual Studio Async CTP Microsoft has also released a CTP of a set of language and framework enhancements to provide a much more powerful asynchronous programming model.   Due to the focus on async programming in all types of platforms (and it being the ONLY option in Silverlight and Win7 phone) a move towards a simpler and more understandable model is always a good thing. This CTP (called Visual Studio Async CTP) can be downloaded here.  You can read more about this CTP on this blog post. MSDN Code Samples Gallery Microsoft has also launched new code samples gallery on their MSDN site: http://code.msdn.microsoft.com/.   This site allows you to easily search for small samples of code related to a particular technology or platform.  If a sample of code you are looking for is not found, you can request one via the site and other developers can see your request and provide a sample to the site to suit your needs.  You can also peruse requested samples and, if you find a scenario where you can provide value, upload your own sample for the benefit of others.  Samples are packaged into the VS .vsix format and include any necessary references/dependencies.  By using .vsix as the deployment mechanism, as samples are installed from the site they are kept in your Visual Studio 2010 Samples Gallery and kept for your future reference. If you get a chance, check out the site and see how it is done.  Although a somewhat simple concept, I was very impressed with their implementation and the way they went about trying to suit a need.  I’ll definitely be looking there in the future as need something or want to share something. MSDN Search Capabilities Another item I learned recently and was not aware of (that might seem trivial to some) is the power of the MSDN site’s search capabilities.  Between the Code Samples Gallery described above and the search enhancements on MSDN, Microsoft is definitely investing in their platform to help provide developers of all skill levels the tools and resources they need to be successful. What do I mean by the MSDN search capability and why should you care? If you go to the MSDN home page (http://msdn.microsoft.com) and use the “Search MSDN with Big” box at the very top of the page you will see some very interesting results.  First, the search actually doesn’t just search the MSDN library it searches: MSDN Library All Microsoft Blogs CodePlex StackOverflow Downloads MSDN Magazine Support Knowledgebase (I’m not sure it even ends there but the above are all I know of) Beyond just searching all the above locations, the results are formatted very nicely to give some contextual information based on where the result came from.  For example, if a keyword search returned results from CodePlex, each row in the search results screen would include a large amount of information specific to CodePlex such as: Looking at the above results immediately tells you everything from the page views to the CodePlex ratings.  All in all, knowing that this much information is indexed and available from a single search location will lead me to utilize this as one of my initial searches for development information.

  Read the article

• Actionscript 3.0 - Enemies do not move right in my platformer game

  - by Christian Basar

  I am making a side-scrolling platformer game in Flash (Actionscript 3.0). I have made lots of progress lately, but I have come across a new problem. I will give some background first. My game level's terrain (or 'floor') is referenced by a MovieClip variable called 'floor.' My desire is to have the Player and enemy characters walk along the terrain. I have gotten the Player character to move on the terrain just fine; he walks up/down hills and falls whenever there is no ground beneath him. Here is the code I created to allow the Player to follow the terrain correctly. Much more code is used to control the Player, but only this code deals with the Player character's following of the terrain and gravity. // If the Player's not on the ground (not touching the 'floor' MovieClip)... if (!onGround) { // Disable ducking downKeyPressed = false; // Increase the Player's 'y' position by his 'y' velocity player.y += playerYVel; } // Increase the 'playerYVel' variable so that the Player will fall // progressively faster down the screen. This code technically // runs "all the time" but in reality it only affects the player // when he's off the ground. playerYVel += gravity; // Give the Player a terminal velocity of 15 px/frame if (playerYVel > 15) { playerYVel = 15; } // If the Player has not hit the 'floor,' increase his falling //speed if (! floor.hitTestPoint(player.x, player.y, true)) { player.y += playerYVel; // The Player is not on the ground when he's not touching it onGround = false; } Since getting this code to work for the Player, I have created a 'SkullDemon' class, which is one of the planned enemies for my game. I want the 'SkullDemon' objects to move along the terrain like the Player does. With lots of great help, I have already coded the EventListeners, etc. necessary for the 'SkullDemons' to move. Unfortunately, I am having trouble getting them to move along the terrain. In fact, they do not touch the terrain at all; they move along the top of the boundary of the 'floor' MovieClip! I had a simple text diagram showing what I mean, but unfortunately Stackoverflow does not format it correctly. I hope my problem is clear from my description. Strangely enough, my code for the Player's movement and the 'SkullDemon's' movement is almost exactly the same, yet the 'SkullDemons' do not move like the Player does. Here is my code for the SkullDemon movement: // Move all of the Skull Demons using this method protected function moveSkullDemons():void { // Go through the whole 'skullDemonContainer' for (var skullDi:int = 0; skullDi < skullDemonContainer.numChildren; skullDi++) { // Set the SkullDemon 'instance' variable to equal the current SkullDemon skullDIns = SkullDemon(skullDemonContainer.getChildAt(skullDi)); // For now, just move the Skull Demons left at 5 units per second skullDIns.x -= 5; // If the Skull Demon has not hit the 'floor,' increase his falling //speed if (! floor.hitTestPoint(skullDIns.x, skullDIns.y, true)) { // Increase the Skull Demon's 'y' position by his 'y' velocity skullDIns.y += skullDIns.sdYVel; // The Skull Demon is not on the ground when he's not touching it skullDIns.sdOnGround = false; } // Increase the 'sdYVel' variable so that the Skull Demon will fall // progressively faster down the screen. This code technically // runs "all the time" but in reality it only affects the Skull Demon // when he's off the ground. if (! skullDIns.sdOnGround) { skullDIns.sdYVel += skullDIns.sdGravity; // Give the Skull Demon a terminal velocity of 15 px/frame if (skullDIns.sdYVel > 15) { skullDIns.sdYVel = 15; } } // What happens when the Skull Demon lands on the ground after a fall? // The Skull Demon is only on the ground ('onGround == true') when // the ground is touching the Skull Demon MovieClip's origin point, // which is at the Skull Demon's bottom centre for (var i:int = 0; i < 10; i++) { // The Skull Demon is only on the ground ('onGround == true') when // the ground is touching the Skull Demon MovieClip's origin point, // which is at the Skull Demon's bottom centre if (floor.hitTestPoint(skullDIns.x, skullDIns.y, true)) { skullDIns.y = skullDIns.y; // Set the Skull Demon's y-axis speed to 0 skullDIns.sdYVel = 0; // The Skull Demon is on the ground again skullDIns.sdOnGround = true; } } } } // End of 'moveSkullDemons()' function It is almost like the 'SkullDemons' are interacting with the 'floor' MovieClip using the hitTestObject() function, and not the hitTestPoint() function which is what I want, and which works for the Player character. I am confused about this problem and would appreciate any help you could give me. Thanks!

  Read the article

• Building a plug-in for Windows Live Writer

  - by mbcrump

  This tutorial will show you how to build a plug-in for Windows Live Writer. Windows Live Writer is a blogging tool that Microsoft provides for free. It includes an open API for .NET developers to create custom plug-ins. In this tutorial, I will show you how easy it is to build one. Open VS2008 or VS2010 and create a new project. Set the target framework to 2.0, Application Type to Class Library and give it a name. In this tutorial, we are going to create a plug-in that generates a twitter message with your blog post name and a TinyUrl link to the blog post.  It will do all of this automatically after you publish your post. Once, we have a new projected created. We need to setup the references. Add a reference to the WindowsLive.Writer.Api.dll located in the C:\Program Files (x86)\Windows Live\Writer\ folder, if you are using X64 version of Windows. You will also need to add a reference to System.Windows.Forms System.Web from the .NET tab as well. Once that is complete, add your “using” statements so that it looks like whats shown below: Live Writer Plug-In "Using" using System; using System.Collections.Generic; using System.Text; using WindowsLive.Writer.Api; using System.Web; Now, we are going to setup some build events to make it easier to test our custom class. Go into the Properties of your project and select Build Events, click edit the Post-build and copy/paste the following line: XCOPY /D /Y /R "$(TargetPath)" "C:\Program Files (x86)\Windows Live\Writer\Plugins\" Your screen should look like the one pictured below: Next, we are going to launch an external program on debug. Click the debug tab and enter C:\Program Files (x86)\Windows Live\Writer\WindowsLiveWriter.exe Your screen should look like the one pictured below:   Now we have a blank project and we need to add some code. We start with adding the attributes for the Live Writer Plugin. Before we get started creating the Attributes, we need to create a GUID. This GUID will uniquely identity our plug-in. So, to create a GUID follow the steps in VS2008/2010. Click Tools from the VS Menu ->Create GUID It will generate a GUID like the one listed below: GUID <Guid("56ED8A2C-F216-420D-91A1-F7541495DBDA")> We only want what’s inside the quotes, so your final product should be: "56ED8A2C-F216-420D-91A1-F7541495DBDA". Go ahead and paste this snipped into your class just above the public class. Live Writer Plug-In Attributes [WriterPlugin("56ED8A2C-F216-420D-91A1-F7541495DBDA",    "Generate Twitter Message",    Description = "After your new post has been published, this plug-in will attempt to generate a Twitter status messsage with the Title and TinyUrl link.",    HasEditableOptions = false,    Name = "Generate Twitter Message",    PublisherUrl = "http://michaelcrump.net")] [InsertableContentSource("Generate Twitter Message")] So far, it should look like the following: Next, we need to implement the PublishNotifcationHook class and override the OnPostPublish. I’m not going to dive into what the code is doing as you should be able to follow pretty easily. The code below is the entire code used in the project. PublishNotificationHook public class Class1 :  PublishNotificationHook  {      public override void OnPostPublish(System.Windows.Forms.IWin32Window dialogOwner, IProperties properties, IPublishingContext publishingContext, bool publish)      {          if (!publish) return;          if (string.IsNullOrEmpty(publishingContext.PostInfo.Permalink))          {              PluginDiagnostics.LogError("Live Tweet didn't execute, due to blank permalink");          }          else          {                var strBlogName = HttpUtility.UrlEncode("#blogged : " + publishingContext.PostInfo.Title);  //Blog Post Title              var strUrlFinal = getTinyUrl(publishingContext.PostInfo.Permalink); //Blog Permalink URL Converted to TinyURL              System.Diagnostics.Process.Start("http://twitter.com/home?status=" + strBlogName + strUrlFinal);            }      } We are going to go ahead and create a method to create the short url (tinyurl). TinyURL Helper Method private static string getTinyUrl(string url) {     var cmpUrl = System.Globalization.CultureInfo.InvariantCulture.CompareInfo;     if (!cmpUrl.IsPrefix(url, "http://tinyurl.com"))     {         var address = "http://tinyurl.com/api-create.php?url=" + url;         var client = new System.Net.WebClient();         return (client.DownloadString(address));     }     return (url); } Go ahead and build your project, it should have copied the .DLL into the Windows Live Writer Plugin Directory. If it did not, then you will want to check your configuration. Once that is complete, open Windows Live Writer and select Tools-> Options-> Plug-ins and enable your plug-in that you just created. Your screen should look like the one pictured below: Go ahead and click OK and publish your blog post. You should get a pop-up with the following: Hit OK and It should open a Twitter and either ask for a login or fill in your status as shown below:   That should do it, you can do so many other things with the API. I suggest that if you want to build something really useful consult the MSDN pages. This plug-in that I created was perfect for what I needed and I hope someone finds it useful.

  Read the article

• SPARC T4-4 Delivers World Record Performance on Oracle OLAP Perf Version 2 Benchmark

  - by Brian

  Oracle's SPARC T4-4 server delivered world record performance with subsecond response time on the Oracle OLAP Perf Version 2 benchmark using Oracle Database 11g Release 2 running on Oracle Solaris 11. The SPARC T4-4 server achieved throughput of 430,000 cube-queries/hour with an average response time of 0.85 seconds and the median response time of 0.43 seconds. This was achieved by using only 60% of the available CPU resources leaving plenty of headroom for future growth. The SPARC T4-4 server operated on an Oracle OLAP cube with a 4 billion row fact table of sales data containing 4 dimensions. This represents as many as 90 quintillion aggregate rows (90 followed by 18 zeros). Performance Landscape Oracle OLAP Perf Version 2 Benchmark 4 Billion Fact Table Rows System Queries/hour Users* Response Time (sec) Average Median SPARC T4-4 430,000 7,300 0.85 0.43 * Users - the supported number of users with a given think time of 60 seconds Configuration Summary and Results Hardware Configuration: SPARC T4-4 server with 4 x SPARC T4 processors, 3.0 GHz 1 TB memory Data Storage 1 x Sun Fire X4275 (using COMSTAR) 2 x Sun Storage F5100 Flash Array (each with 80 FMODs) Redo Storage 1 x Sun Fire X4275 (using COMSTAR with 8 HDD) Software Configuration: Oracle Solaris 11 11/11 Oracle Database 11g Release 2 (11.2.0.3) with Oracle OLAP option Benchmark Description The Oracle OLAP Perf Version 2 benchmark is a workload designed to demonstrate and stress the Oracle OLAP product's core features of fast query, fast update, and rich calculations on a multi-dimensional model to support enhanced Data Warehousing. The bulk of the benchmark entails running a number of concurrent users, each issuing typical multidimensional queries against an Oracle OLAP cube consisting of a number of years of sales data with fully pre-computed aggregations. The cube has four dimensions: time, product, customer, and channel. Each query user issues approximately 150 different queries. One query chain may ask for total sales in a particular region (e.g South America) for a particular time period (e.g. Q4 of 2010) followed by additional queries which drill down into sales for individual countries (e.g. Chile, Peru, etc.) with further queries drilling down into individual stores, etc. Another query chain may ask for yearly comparisons of total sales for some product category (e.g. major household appliances) and then issue further queries drilling down into particular products (e.g. refrigerators, stoves. etc.), particular regions, particular customers, etc. Results from version 2 of the benchmark are not comparable with version 1. The primary difference is the type of queries along with the query mix. Key Points and Best Practices Since typical BI users are often likely to issue similar queries, with different constants in the where clauses, setting the init.ora prameter "cursor_sharing" to "force" will provide for additional query throughput and a larger number of potential users. Except for this setting, together with making full use of available memory, out of the box performance for the OLAP Perf workload should provide results similar to what is reported here. For a given number of query users with zero think time, the main measured metrics are the average query response time, the median query response time, and the query throughput. A derived metric is the maximum number of users the system can support achieving the measured response time assuming some non-zero think time. The calculation of the maximum number of users follows from the well-known response-time law N = (rt + tt) * tp where rt is the average response time, tt is the think time and tp is the measured throughput. Setting tt to 60 seconds, rt to 0.85 seconds and tp to 119.44 queries/sec (430,000 queries/hour), the above formula shows that the T4-4 server will support 7,300 concurrent users with a think time of 60 seconds and an average response time of 0.85 seconds. For more information see chapter 3 from the book "Quantitative System Performance" cited below. -- See Also Quantitative System Performance Computer System Analysis Using Queueing Network Models Edward D. Lazowska, John Zahorjan, G. Scott Graham, Kenneth C. Sevcik external local Oracle Database 11g – Oracle OLAP oracle.com OTN SPARC T4-4 Server oracle.com OTN Oracle Solaris oracle.com OTN Oracle Database 11g Release 2 oracle.com OTN Disclosure Statement Copyright 2012, Oracle and/or its affiliates. All rights reserved. Oracle and Java are registered trademarks of Oracle and/or its affiliates. Other names may be trademarks of their respective owners. Results as of 11/2/2012.

  Read the article

• Can not print after upgrading from 12.x to 14.04

  - by user318889

  After upgrading from V12.04 to V14.04 I am not able to print. I am using an HP LaserJet 400 M451dn. The printer troubleshooter told me that there is no solution to the problem. This is the output of the advanced diagnositc output. (Due to limited space I cut the output!) Can anybody tell me what is going wrong. I am using the printer via USB ? Page 1 (Scheduler not running?): {'cups_connection_failure': False} Page 2 (Is local server publishing?): {'local_server_exporting_printers': False} Page 3 (Choose printer): {'cups_dest': , 'cups_instance': None, 'cups_queue': u'HP-LaserJet-400-color-M451dn', 'cups_queue_listed': True} Page 4 (Check printer sanity): {'cups_device_uri_scheme': u'hp', 'cups_printer_dict': {'device-uri': u'hp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670', 'printer-info': u'Hewlett-Packard HP LaserJet 400 color M451dn', 'printer-is-shared': True, 'printer-location': u'Pinatubo', 'printer-make-and-model': u'HP LJ 300-400 color M351-M451 Postscript (recommended)', 'printer-state': 4, 'printer-state-message': u'', 'printer-state-reasons': [u'none'], 'printer-type': 8556636, 'printer-uri-supported': u'ipp://localhost:631/printers/HP-LaserJet-400-color-M451dn'}, 'cups_printer_remote': False, 'hplip_output': (['', '\x1b[01mHP Linux Imaging and Printing System (ver. 3.14.6)\x1b[0m', '\x1b[01mDevice Information Utility ver. 5.2\x1b[0m', '', 'Copyright (c) 2001-13 Hewlett-Packard Development Company, LP', 'This software comes with ABSOLUTELY NO WARRANTY.', 'This is free software, and you are welcome to distribute it', 'under certain conditions. See COPYING file for more details.', '', '', '\x1b[01mhp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670\x1b[0m', '', '\x1b[01mDevice Parameters (dynamic data):\x1b[0m', '\x1b[01m Parameter Value(s) \x1b[0m', ' ---------------------------- ----------------------------------------------------------', ' back-end hp ', " cups-printers ['HP-LaserJet-400-color-M451dn'] ", ' cups-uri hp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670 ', ' dev-file ', ' device-state -1 ', ' device-uri hp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670 ', ' deviceid ', ' error-state 101 ', ' host ', ' is-hp True ', ' panel 0 ', ' panel-line1 ', ' panel-line2 ', ' port 1 ', ' serial CNFF308670 ', ' status-code 5002 ', ' status-desc ', '\x1b[01m', 'Model Parameters (static data):\x1b[0m', '\x1b[01m Parameter Value(s) \x1b[0m', ' ---------------------------- ----------------------------------------------------------', ' align-type 0 ', ' clean-type 0 ', ' color-cal-type 0 ', ' copy-type 0 ', ' embedded-server-type 0 ', ' fax-type 0 ', ' fw-download False ', ' icon hp_color_laserjet_cp2025.png ', ' io-mfp-mode 1 ', ' io-mode 1 ', ' io-support 6 ', ' job-storage 0 ', ' linefeed-cal-type 0 ', ' model HP_LaserJet_400_color_M451dn ', ' model-ui HP LaserJet 400 Color m451dn ', ' model1 HP LaserJet 400 Color M451dn ', ' monitor-type 0 ', ' panel-check-type 0 ', ' pcard-type 0 ', ' plugin 0 ', ' plugin-reason 0 ', ' power-settings 0 ', ' ppd-name lj_300_400_color_m351_m451 ', ' pq-diag-type 0 ', ' r-type 0 ', ' r0-agent1-kind 4 ', ' r0-agent1-sku CE410A/CE410X ', ' r0-agent1-type 1 ', ' r0-agent2-kind 4 ', ' r0-agent2-sku CE411A ', ' r0-agent2-type 4 ', ' r0-agent3-kind 4 ', ' r0-agent3-sku CE413A ', ' r0-agent3-type 5 ', ' r0-agent4-kind 4 ', ' r0-agent4-sku CE412A ', ' r0-agent4-type 6 ', ' scan-src 0 ', ' scan-type 0 ', ' status-battery-check 0 ', ' status-dynamic-counters 0 ', ' status-type 3 ', ' support-released True ', ' support-subtype 2202411 ', ' support-type 2 ', ' support-ver 3.12.2 ', " tech-class ['Postscript'] ", " tech-subclass ['Normal'] ", ' tech-type 4 ', ' usb-pid 3882 ', ' usb-vid 1008 ', ' wifi-config 0 ', '\x1b[01m', 'Status History (most recent first):\x1b[0m', '\x1b[01m Date/Time Code Status Description User Job ID \x1b[0m', ' -------------------- ----- ---------------------------------------- -------- --------', ' 08/21/14 00:07:25 5012 Device communication error richard 0 ', ' 08/20/14 13:42:44 500 Started a print job richard 4214 ', '', '', 'Done.', ''], ['\x1b[35;01mwarning: No display found.\x1b[0m', '\x1b[31;01merror: hp-info -u/--gui requires Qt4 GUI support. Entering interactive mode.\x1b[0m', '\x1b[31;01merror: Unable to communicate with device (code=12): hp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670\x1b[0m', '\x1b[31;01merror: Error opening device (Device not found).\x1b[0m', ''], 0), 'is_cups_class': False, 'local_cups_queue_attributes': {'charset-configured': u'utf-8', 'charset-supported': [u'us-ascii', u'utf-8'], 'color-supported': True, 'compression-supported': [u'none', u'gzip'], 'copies-default': 1, 'copies-supported': (1, 9999), 'cups-version': u'1.7.2', 'device-uri': u'hp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670', 'document-format-default': u'application/octet-stream', 'document-format-supported': [u'application/octet-stream', u'application/pdf', u'application/postscript', u'application/vnd.adobe-reader-postscript', u'application/vnd.cups-command', u'application/vnd.cups-pdf', u'application/vnd.cups-pdf-banner', u'application/vnd.cups-postscript', u'application/vnd.cups-raw', u'application/vnd.samsung-ps', u'application/x-cshell', u'application/x-csource', u'application/x-perl', u'application/x-shell', u'image/gif', u'image/jpeg', u'image/png', u'image/tiff', u'image/urf', u'image/x-bitmap', u'image/x-photocd', u'image/x-portable-anymap', u'image/x-portable-bitmap', u'image/x-portable-graymap', u'image/x-portable-pixmap', u'image/x-sgi-rgb', u'image/x-sun-raster', u'image/x-xbitmap', u'image/x-xpixmap', u'image/x-xwindowdump', u'text/css', u'text/html', u'text/plain'], 'finishings-default': 3, 'finishings-supported': [3], 'generated-natural-language-supported': [u'en-us'], 'ipp-versions-supported': [u'1.0', u'1.1', u'2.0', u'2.1'], 'ippget-event-life': 15, 'job-creation-attributes-supported': [u'copies', u'finishings', u'ipp-attribute-fidelity', u'job-hold-until', u'job-name', u'job-priority', u'job-sheets', u'media', u'media-col', u'multiple-document-handling', u'number-up', u'output-bin', u'orientation-requested', u'page-ranges', u'print-color-mode', u'print-quality', u'printer-resolution', u'sides'], 'job-hold-until-default': u'no-hold', 'job-hold-until-supported': [u'no-hold', u'indefinite', u'day-time', u'evening', u'night', u'second-shift', u'third-shift', u'weekend'], 'job-ids-supported': True, 'job-k-limit': 0, 'job-k-octets-supported': (0, 470914416), 'job-page-limit': 0, 'job-priority-default': 50, 'job-priority-supported': [100], 'job-quota-period': 0, 'job-settable-attributes-supported': [u'copies', u'finishings', u'job-hold-until', u'job-name', u'job-priority', u'media', u'media-col', u'multiple-document-handling', u'number-up', u'output-bin', u'orientation-requested', u'page-ranges', u'print-color-mode', u'print-quality', u'printer-resolution', u'sides'], 'job-sheets-default': (u'none', u'none'), 'job-sheets-supported': [u'none', u'classified', u'confidential', u'form', u'secret', u'standard', u'topsecret', u'unclassified'], 'jpeg-k-octets-supported': (0, 470914416), 'jpeg-x-dimension-supported': (0, 65535), 'jpeg-y-dimension-supported': (1, 65535), 'marker-change-time': 0, 'media-bottom-margin-supported': [423], 'media-col-default': u'(unknown IPP value tag 0x34)', 'media-col-supported': [u'media-bottom-margin', u'media-left-margin', u'media-right-margin', u'media-size', u'media-source', u'media-top-margin', u'media-type'], 'media-default': u'iso_a4_210x297mm', 'media-left-margin-supported': [423], 'media-right-margin-supported': [423],

  Read the article

• Gamification at OOW

  - by erikanollwebb

  Last week was Oracle OpenWorld, and for those of you not in tech or downtown San Francisco, that might not mean a whole lot.  However, if you are familiar with it, Oracle OpenWorld is our premier customer event.  This year, more than 50,000 people attended.  It's not a good week to visit San Francisco on vacation because Oracle customers take over all the hotels in town!  It was crazy, but a lot of fun and it's a great opportunity for the Apps UX group to do customer research with a range of customers.  This year, more than 100+ customers and partners took the time to team up with our UX experts and provide feedback on new designs and ideas. Over three days,  UX teams conducted 8  one-on-one user feedback sessions, 4 focus groups and 7 surveys. In addition, we conducted a voice capture activity and were able to collect close to 70 speech samples at the lab and DEMOgrounds. This was a great opportunity for us to do some testing on some specific gamification concepts with a set of business analysts.  We pulled in 8 folks for a focus group on gamification concepts and whether they thought those would work for their teams. To get ready for this, my designer extraordinaire, Andrea Cantú, flew into town and we spent almost a week locked in a room together brainstorming design ideas.  We killed a few trees trying to get all of our concepts and other examples together in the process, but in the end, we put together a whole series of examples of how you might gamify an Oracle app (in this case, CRM).  Andrea is a genius for this kind of thing and the comps she created looked great.  Here's a picture of her hard at work!  We also had the good fortune to have my boss, Laurie Pattison and my usability contractor, Shobana Subramanian there to note take and observe as well.  Here's a few shots of us, hard at work preparing for the day (or checking out something on Laurie's iPhone...) To start things off, we gave an overview of gamification and I talked about what it's used for.  Then we gave the participants a scenario about our sales person and what we were trying to get her to do. It was a great opportunity to highlight what our business goals might be and why we might want to add game mechanics.  It was also a good way to get them thinking about how that might work for them in their environments and workplaces. There were some surprises for the day.  We asked how many of them were already familiar with the concept of gamification--only two people had heard of it and only one was using game mechanics in his work.  That's in contrast to a survey we just ran internally with folks in a dev org where almost 50% of about 450 respondents had heard of gamification.  As we discussed the ways game mechanics could be used, it became clear that many of the folks had seen some game mechanics in action but didn't know that's what they were.  We also noticed that the folks in this group felt that if they were trying to sell the concept in their orgs, they wouldn't call it gamification.  That's not a huge surprise to me--they said what we've heard in the past, that gamification does not seem like a serious term for enterprise software.  They said they'd sell it with the goals--as a means to increase behaviors by rewarding users for activities.  It's a funny problem.  The word puts some folks off, but at the same time, I haven't seen another one word description that quite captures the range of things that "gamification" can cover.  My guess is that the more mainstream the term becomes, the more desensitized we'll become to the idea the it's trivializing enterprise software in some way.  Still, it was interesting to note that this group still felt that they would not take this concept to their bosses or teams and call it "gamification".  They focused on the goals, and how we could incentivize desired behaviors with game mechanics.  As I have already stated in other posts, I feel like my org is more receptive to discussing how this is just a more transparent type of usability and user experience methods than talking about gamification.  That's the argument they said they would use. All in all, it was a good session.  I love getting to talk to customers, present ideas and concepts, and get their feedback and input.  It's the type of thing that really helps drive our designs and keeps us grounded in what our customers need/want.  We're already planning where to get more feedback opportunities in the coming months. 

  Read the article

• Repeated disconnects on WPA PEAP network

  - by exasperated

  My school has a WPA PEAP network with GTC inner authentication. I am able to connect to the network, but once I load a website or two, the network become unresponsive (i.e. in Chromium, it gets stuck at "Sending request"), and I'm eventually disconnected. Any help will be greatly appreciated. Here's some log output. I can provide more if needed: Ubuntu 13.04 3.8.0-32-generic x86_64 lsusb: 03:00.0 Network controller: Intel Corporation Centrino Advanced-N 6235 (rev 24) lsmod: iwldvm                241872  0  mac80211              606457  1 iwldvm iwlwifi               173516  1 iwldvm cfg80211              511019  3 iwlwifi,mac80211,iwldvm dmesg: [    3.501227] iwlwifi 0000:03:00.0: irq 46 for MSI/MSI-X [    3.503541] iwlwifi 0000:03:00.0: loaded firmware version 18.168.6.1 [    3.527153] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEBUG disabled [    3.527162] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEBUGFS enabled [    3.527170] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEVICE_TRACING enabled [    3.527178] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEVICE_TESTMODE enabled [    3.527186] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_P2P disabled [    3.527192] iwlwifi 0000:03:00.0: Detected Intel(R) Centrino(R) Advanced-N 6235 AGN, REV=0xB0 [    3.527240] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [    3.551049] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [  375.153065] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [  375.159727] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [  375.553201] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [  375.559871] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 1892.110738] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 1892.117357] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 5227.235372] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 5227.242122] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 5817.817954] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 5817.824560] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 5824.571917] iwlwifi 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 5824.571929] iwlwifi 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 5824.571935] iwlwifi 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [ 6956.290061] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 6956.296671] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 6963.080560] iwlwifi 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 6963.080566] iwlwifi 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 6963.080570] iwlwifi 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [ 7613.469241] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 7613.475870] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 7620.201265] iwlwifi 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 7620.201278] iwlwifi 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 7620.201285] iwlwifi 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [ 8232.762453] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 8232.769065] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 8239.581772] iwlwifi 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 8239.581784] iwlwifi 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 8239.581792] iwlwifi 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [13763.634808] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [13763.641427] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [16955.598953] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [16955.605574] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 lshw:    *-network        description: Wireless interface        product: Centrino Advanced-N 6235        vendor: Intel Corporation        physical id: 0        bus info: pci@0000:03:00.0        logical name: wlan0        version: 24        serial: b4:b6:76:a0:4b:3c        width: 64 bits        clock: 33MHz        capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless        configuration: broadcast=yes driver=iwlwifi driverversion=3.8.0-32-generic firmware=18.168.6.1 ip=10.250.169.96 latency=0 link=yes multicast=yes wireless=IEEE 802.11abgn        resources: irq:46 memory:f7c00000-f7c01fff iwlist scan: Cell 02 - Address: 24:DE:C6:B0:C7:D9                     Channel:36                     Frequency:5.18 GHz (Channel 36)                     Quality=29/70  Signal level=-81 dBm                       Encryption key:on                     ESSID:"CatChat2x"                     Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s                               36 Mb/s; 48 Mb/s; 54 Mb/s                     Mode:Master                     Extra:tsf=0000004ff3fe419b                     Extra: Last beacon: 27820ms ago                     IE: Unknown: 0009436174436861743278                     IE: Unknown: 01088C129824B048606C                     IE: Unknown: 030124                     IE: IEEE 802.11i/WPA2 Version 1                         Group Cipher : CCMP                         Pairwise Ciphers (1) : CCMP                         Authentication Suites (1) : 802.1x                     IE: Unknown: 2D1ACC011BFFFF000000000000000000000000000000000000000000                     IE: Unknown: 3D1624001B000000FF000000000000000000000000000000                     IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00                     IE: Unknown: DD1E00904C33CC011BFFFF000000000000000000000000000000000000000000                     IE: Unknown: DD1A00904C3424001B000000FF000000000000000000000000000000           Cell 04 - Address: 24:DE:C6:B0:C3:E9                     Channel:149                     Frequency:5.745 GHz                     Quality=28/70  Signal level=-82 dBm                       Encryption key:on                     ESSID:"CatChat2x"                     Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s                               36 Mb/s; 48 Mb/s; 54 Mb/s                     Mode:Master                     Extra:tsf=000000181f60e19c                     Extra: Last beacon: 28680ms ago                     IE: Unknown: 0009436174436861743278                     IE: Unknown: 01088C129824B048606C                     IE: Unknown: 030195                     IE: Unknown: 050400010000                     IE: IEEE 802.11i/WPA2 Version 1                         Group Cipher : CCMP                         Pairwise Ciphers (1) : CCMP                         Authentication Suites (1) : 802.1x                     IE: Unknown: 2D1ACC011BFFFF000000000000000000000000000000000000000000                     IE: Unknown: 3D1695001B000000FF000000000000000000000000000000                     IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00                     IE: Unknown: DD1E00904C33CC011BFFFF000000000000000000000000000000000000000000                     IE: Unknown: DD1A00904C3495001B000000FF000000000000000000000000000000                     IE: Unknown: DD07000B8601040817                     IE: Unknown: DD0E000B860103006170313930333032           Cell 09 - Address: 24:DE:C6:B0:C0:29                     Channel:149                     Frequency:5.745 GHz                     Quality=39/70  Signal level=-71 dBm                       Encryption key:on                     ESSID:"CatChat2x"                     Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s                               36 Mb/s; 48 Mb/s; 54 Mb/s                     Mode:Master                     Extra:tsf=00000112fb688ede                     Extra: Last beacon: 27716ms ago ifconfig (while connected): wlan0     Link encap:Ethernet  HWaddr b4:b6:76:a0:4b:3c             inet addr:10.250.16.220  Bcast:10.250.31.255  Mask:255.255.240.0           inet6 addr: fe80::b6b6:76ff:fea0:4b3c/64 Scope:Link           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1           RX packets:230023 errors:0 dropped:0 overruns:0 frame:0           TX packets:130970 errors:0 dropped:0 overruns:0 carrier:0           collisions:0 txqueuelen:1000            RX bytes:255999759 (255.9 MB)  TX bytes:16652605 (16.6 MB) iwconfig (while connected): wlan0     IEEE 802.11abgn  ESSID:"CatChat2x"             Mode:Managed  Frequency:5.745 GHz  Access Point: 24:DE:C6:B0:C0:29              Bit Rate=6 Mb/s   Tx-Power=15 dBm              Retry  long limit:7   RTS thr:off   Fragment thr:off           Power Management:off           Link Quality=36/70  Signal level=-74 dBm             Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0           Tx excessive retries:0  Invalid misc:3   Missed beacon:0

  Read the article

• Database Rebuild

  - by Robert May

  I promised I’d have a simpler mechanism for rebuilding the database.  Below is a complete MSBuild targets file for rebuilding the database from scratch.  I don’t know if I’ve explained the rational for this.  The reason why you’d WANT to do this is so that each developer has a clean version of the database on their local machine.  This also includes the continuous integration environment.  Basically, you can do whatever you want to the database without fear, and in a minute or two, have a completely rebuilt database structure. DBDeploy (including the KTSC build task for dbdeploy) is used in this script to do change tracking on the database itself.  The MSBuild ExtensionPack is used in this target file.  You can get an MSBuild DBDeploy task here. There are two database scripts that you’ll see below.  First is the task for creating an admin (dbo) user in the system.  This script looks like the following: USE [master] GO If not Exists (select Name from sys.sql_logins where name = '$(User)') BEGIN CREATE LOGIN [$(User)] WITH PASSWORD=N'$(Password)', DEFAULT_DATABASE=[$(DatabaseName)], CHECK_EXPIRATION=OFF, CHECK_POLICY=OFF END GO EXEC master..sp_addsrvrolemember @loginame = N'$(User)', @rolename = N'sysadmin' GO USE [$(DatabaseName)] GO CREATE USER [$(User)] FOR LOGIN [$(User)] GO ALTER USER [$(User)] WITH DEFAULT_SCHEMA=[dbo] GO EXEC sp_addrolemember N'db_owner', N'$(User)' GO The second creates the changelog table.  This script can also be found in the dbdeploy.net install\scripts directory. CREATE TABLE changelog ( change_number INTEGER NOT NULL, delta_set VARCHAR(10) NOT NULL, start_dt DATETIME NOT NULL, complete_dt DATETIME NULL, applied_by VARCHAR(100) NOT NULL, description VARCHAR(500) NOT NULL ) GO ALTER TABLE changelog ADD CONSTRAINT Pkchangelog PRIMARY KEY (change_number, delta_set) GO Finally, Here’s the targets file. <Projectxmlns="http://schemas.microsoft.com/developer/msbuild/2003" ToolsVersion="4.0" DefaultTargets="Update">   <PropertyGroup>     <DatabaseName>TestDatabase</DatabaseName>     <Server>localhost</Server>     <ScriptDirectory>.\Scripts</ScriptDirectory>     <RebuildDirectory>.\Rebuild</RebuildDirectory>     <TestDataDirectory>.\TestData</TestDataDirectory>     <DbDeploy>.\DBDeploy</DbDeploy>     <User>TestUser</User>     <Password>TestPassword</Password>     <BCP>bcp</BCP>     <BCPOptions>-S$(Server) -U$(User) -P$(Password) -N -E -k</BCPOptions>     <OutputFileName>dbDeploy-output.sql</OutputFileName>     <UndoFileName>dbDeploy-output-undo.sql</UndoFileName>     <LastChangeToApply>99999</LastChangeToApply>   </PropertyGroup>     <ImportProject="$(MSBuildExtensionsPath)\ExtensionPack\4.0\MSBuild.ExtensionPack.tasks"/>   <UsingTask TaskName="Ktsc.Build.DBDeploy" AssemblyFile="$(DbDeploy)\Ktsc.Build.dll"/>   <ItemGroup>     <VariableInclude="DatabaseName">       <Value>$(DatabaseName)</Value>     </Variable>     <VariableInclude="Server">       <Value>$(Server)</Value>     </Variable>     <VariableInclude="User">       <Value>$(User)</Value>     </Variable>     <VariableInclude="Password">       <Value>$(Password)</Value>     </Variable>   </ItemGroup>     <TargetName="Rebuild">     <!--Take the database offline to disconnect any users. Requires that the current user is an admin of the sql server machine.-->     <MSBuild.ExtensionPack.SqlServer.SqlCmd Variables="@(Variable)" Database="$(DatabaseName)" TaskAction="Execute" CommandLineQuery ="ALTER DATABASE $(DatabaseName) SET OFFLINE WITH ROLLBACK IMMEDIATE"/>         <!--Bring it back online.  If you don't, the database files won't be deleted.-->     <MSBuild.ExtensionPack.Sql2008.DatabaseTaskAction="SetOnline" DatabaseItem="$(DatabaseName)"/>     <!--Delete the database, removing the existing files.-->     <MSBuild.ExtensionPack.Sql2008.DatabaseTaskAction="Delete" DatabaseItem="$(DatabaseName)"/>     <!--Create the new database in the default database path location.-->     <MSBuild.ExtensionPack.Sql2008.DatabaseTaskAction="Create" DatabaseItem="$(DatabaseName)" Force="True"/>         <!--Create admin user-->     <MSBuild.ExtensionPack.SqlServer.SqlCmd TaskAction="Execute" Server="(local)" Database="$(DatabaseName)" InputFiles="$(RebuildDirectory)\0002 Create Admin User.sql" Variables="@(Variable)" />     <!--Create the dbdeploy changelog.-->     <MSBuild.ExtensionPack.SqlServer.SqlCmd TaskAction="Execute" Server="(local)" Database="$(DatabaseName)" LogOn="$(User)" Password="$(Password)" InputFiles="$(RebuildDirectory)\0003 Create Changelog.sql" Variables="@(Variable)" />     <CallTarget Targets="Update;ImportData"/>     </Target>    <TargetName="Update" DependsOnTargets="CreateUpdateScript">     <MSBuild.ExtensionPack.SqlServer.SqlCmd TaskAction="Execute" Server="(local)" Database="$(DatabaseName)" LogOn="$(User)" Password="$(Password)" InputFiles="$(OutputFileName)" Variables="@(Variable)" />   </Target>   <TargetName="CreateUpdateScript">     <ktsc.Build.DBDeploy DbType="mssql"                                        DbConnection="User=$(User);Password=$(Password);Data Source=$(Server);Initial Catalog=$(DatabaseName);"                                        Dir="$(ScriptDirectory)"                                        OutputFile="..\$(OutputFileName)"                                        UndoOutputFile="..\$(UndoFileName)"                                        LastChangeToApply="$(LastChangeToApply)"/>   </Target>     <TargetName="ImportData">     <ItemGroup>       <TestData Include="$(TestDataDirectory)\*.dat"/>     </ItemGroup>     <ExecCommand="$(BCP) $(DatabaseName).dbo.%(TestData.Filename) in&quot;%(TestData.Identity)&quot;$(BCPOptions)"/>   </Target> </Project> Technorati Tags: MSBuild

  Read the article

• SharePoint 2010 Diagnostic Studio Remote Diag

  - by juanlarios

  I have had some time this week to try out some tools that I have been meaning to try out. This week I am trying out the SP 2010 Diagnostic Studio. I installed it successfully and tried it on my development evironment. I was able to build a report and a snapshot of the environment. I decided to turn my attention to my Employer's intranet environment. This would allow me to analyze it and measure it against benchmarks. I didn't want to install the Diagnostic studio on the Production Envorinment, lucky for me, the Diagnostic studio can be run remotely, well...kind of. Issue My development environment is a stand alone, full installation of SharePoint 2010 Server. It has Office 2010, SQL 2008 Enterprise, a DC...well you get the point, it's jammed packed! But more importantly it's a stand alone, self contained VM environment. Well Microsoft has instructions as to how to connect remotely with Diagnostic Studio here. The deciving part of this is that the SP2010DS prompts you for credentails. So I thought I was getting the right account to run the reports. I tried all the Power Shell commands in the link above but I still ended up getting the following errors: 06/28/2011 12:50:18    Connecting to remote server failed with the following error message : The WinRM client cannot process the request...If the SPN exists, but CredSSP cannot use Kerberos to validate the identity of the target computer and you still want to allow the delegation of the user credentials to the target computer, use gpedit.msc and look at the following policy: Computer Configuration -> Administrative Templates -> System -> Credentials Delegation -> Allow Fresh Credentials with NTLM-only Server Authentication.  Verify that it is enabled and configured with an SPN appropriate for the target computer. For example, for a target computer name "myserver.domain.com", the SPN can be one of the following: WSMAN/myserver.domain.com or WSMAN/*.domain.com. Try the request again after these changes. For more information, see the about_Remote_Troubleshooting Help topic. 06/28/2011 12:54:47    Access to the path '\\<targetserver>\C$\Users\<account logging in>\AppData\Local\Temp' is denied. You might also get an error message like this: The WinRM client cannot process the request. A computer policy does not allow the delegation of the user credentials to the target computer. Explanation After looking at the event logs on the target environment, I noticed that there were a several Security Exceptions. After looking at the specifics around who was denied access, I was able to see the account that was being denied access, it was the client machine administrator account. Well of course that was never going to work!!! After some quick Googling, the last error message above will lead you to edit the Local Group Policy on the client server. And although there are instructions from microsoft around doing this, it really will not work in this scenario. Notice the Description and how it only applices to authentication mentioned? Resolution I can tell you what I did, but I wish there was a better way but I simply don't know if it's duable any other way. Because my development environment had it's own DC, I didn't really want to mess with Kerberos authentication. I would also not be smart to connect that server to the domain, considering it has it's own DC. I ended up installing SharePoint 2010 Diagnostic Studio on another Windows 7 Dev environment I have, and connected the machien to the domain. I ran all the necesary remote credentials commands mentioned here. Those commands add the group policy for you! Once I did this I was able to authenticate properly and I was able to get the reports. Conclusion   You can run SharePoint 2010 Diagnostic Studio Remotely but it will require some specific scenarions. A couple of things I should mention is that as far as I understand, SP2010 DS, will install agents on your target environment to run tests and retrieve the data. I was a Farm Administrator, and also a Server Admin on SharePoint Server. I am not 100% sure if you need all those permissions but I that's just what I have to my internal intranet.   I deally I would like to have a machine that I can have SharePoint 2010 DIagnostic Studio installed and I can run that against client environments. It appears that I will not be able to do that, unless I enable Kerberos on my Windows 7 Machine now. If you have it installed in the same way I would like to have it, please let me know, I'll keep trying to get what I'm after. Hope this helps someone out there doing the same.

  Read the article

• Breaking 1NF to model subset constraints. Does this sound sane?

  - by Chris Travers

  My first question here. Appologize if it is in the wrong forum but this seems pretty conceptual. I am looking at doing something that goes against conventional wisdom and want to get some feedback as to whether this is totally insane or will result in problems, so critique away! I am on PostgreSQL 9.1 but may be moving to 9.2 for this part of this project. To re-iterate: Does it seem sane to break 1NF in this way? I am not looking for debugging code so much as where people see problems that this might lead. The Problem In double entry accounting, financial transactions are journal entries with an arbitrary number of lines. Each line has either a left value (debit) or a right value (credit) which can be modelled as a single value with negatives as debits and positives as credits or vice versa. The sum of all debits and credits must equal zero (so if we go with a single amount field, sum(amount) must equal zero for each financial journal entry). SQL-based databases, pretty much required for this sort of work, have no way to express this sort of constraint natively and so any approach to enforcing it in the database seems rather complex. The Write Model The journal entries are append only. There is a possibility we will add a delete model but it will be subject to a different set of restrictions and so is not applicable here. If and when we allow deletes, we will probably do them using a simple ON DELETE CASCADE designation on the foreign key, and require that deletes go through a dedicated stored procedure which can enforce the other constraints. So inserts and selects have to be accommodated but updates and deletes do not for this task. My Proposed Solution My proposed solution is to break first normal form and model constraints on arrays of tuples, with a trigger that breaks the rows out into another table. CREATE TABLE journal_line ( entry_id bigserial primary key, account_id int not null references account(id), journal_entry_id bigint not null, -- adding references later amount numeric not null ); I would then add "table methods" to extract debits and credits for reporting purposes: CREATE OR REPLACE FUNCTION debits(journal_line) RETURNS numeric LANGUAGE sql IMMUTABLE AS $$ SELECT CASE WHEN $1.amount < 0 THEN $1.amount * -1 ELSE NULL END; $$; CREATE OR REPLACE FUNCTION credits(journal_line) RETURNS numeric LANGUAGE sql IMMUTABLE AS $$ SELECT CASE WHEN $1.amount > 0 THEN $1.amount ELSE NULL END; $$; Then the journal entry table (simplified for this example): CREATE TABLE journal_entry ( entry_id bigserial primary key, -- no natural keys :-( journal_id int not null references journal(id), date_posted date not null, reference text not null, description text not null, journal_lines journal_line[] not null ); Then a table method and and check constraints: CREATE OR REPLACE FUNCTION running_total(journal_entry) returns numeric language sql immutable as $$ SELECT sum(amount) FROM unnest($1.journal_lines); $$; ALTER TABLE journal_entry ADD CONSTRAINT CHECK (((journal_entry.running_total) = 0)); ALTER TABLE journal_line ADD FOREIGN KEY journal_entry_id REFERENCES journal_entry(entry_id); And finally we'd have a breakout trigger: CREATE OR REPLACE FUNCTION je_breakout() RETURNS TRIGGER LANGUAGE PLPGSQL AS $$ BEGIN IF TG_OP = 'INSERT' THEN INSERT INTO journal_line (journal_entry_id, account_id, amount) SELECT NEW.id, account_id, amount FROM unnest(NEW.journal_lines); RETURN NEW; ELSE RAISE EXCEPTION 'Operation Not Allowed'; END IF; END; $$; And finally CREATE TRIGGER AFTER INSERT OR UPDATE OR DELETE ON journal_entry FOR EACH ROW EXECUTE_PROCEDURE je_breaout(); Of course the example above is simplified. There will be a status table that will track approval status allowing for separation of duties, etc. However the goal here is to prevent unbalanced transactions. Any feedback? Does this sound entirely insane? Standard Solutions? In getting to this point I have to say I have looked at four different current ERP solutions to this problems: Represent every line item as a debit and a credit against different accounts. Use of foreign keys against the line item table to enforce an eventual running total of 0 Use of constraint triggers in PostgreSQL Forcing all validation here solely through the app logic. My concerns are that #1 is pretty limiting and very hard to audit internally. It's not programmer transparent and so it strikes me as being difficult to work with in the future. The second strikes me as being very complex and required a series of contraints and foreign keys against self to make work, and therefore it strikes me as complex, hard to sort out at least in my mind, and thus hard to work with. The fourth could be done as we force all access through stored procedures anyway and this is the most common solution (have the app total things up and throw an error otherwise). However, I think proof that a constraint is followed is superior to test cases, and so the question becomes whether this in fact generates insert anomilies rather than solving them. If this is a solved problem it isn't the case that everyone agrees on the solution....

  Read the article

• How to Implement Single Sign-On between Websites

  - by hmloo

  Introduction Single sign-on (SSO) is a way to control access to multiple related but independent systems, a user only needs to log in once and gains access to all other systems. a lot of commercial systems that provide Single sign-on solution and you can also choose some open source solutions like Opensso, CAS etc. both of them use centralized authentication and provide more robust authentication mechanism, but if each system has its own authentication mechanism, how do we provide a seamless transition between them. Here I will show you the case. How it Works The method we’ll use is based on a secret key shared between the sites. Origin site has a method to build up a hashed authentication token with some other parameters and redirect the user to the target site. variables Status Description ssoEncode required hash(ssoSharedSecret + , + ssoTime + , + ssoUserName) ssoTime required timestamp with format YYYYMMDDHHMMSS used to prevent playback attacks ssoUserName required unique username; required when a user is logged in Note : The variables will be sent via POST for security reasons Building a Single Sign-On Solution Origin Site has function to 1. Create the URL for your Request. 2. Generate required authentication parameters 3. Redirect to target site. using System; using System.Web.Security; using System.Text; public partial class _Default : System.Web.UI.Page { protected void Page_Load(object sender, EventArgs e) { string postbackUrl = "http://www.targetsite.com/sso.aspx"; string ssoTime = DateTime.Now.ToString("yyyyMMddHHmmss"); string ssoUserName = User.Identity.Name; string ssoSharedSecret = "58ag;ai76"; // get this from config or similar string ssoHash = FormsAuthentication.HashPasswordForStoringInConfigFile(string.Format("{0},{1},{2}", ssoSharedSecret, ssoTime, ssoUserName), "md5"); string value = string.Format("{0}:{1},{2}", ssoHash,ssoTime, ssoUserName); Response.Clear(); StringBuilder sb = new StringBuilder(); sb.Append("<html>"); sb.AppendFormat(@"<body onload='document.forms[""form""].submit()'>"); sb.AppendFormat("<form name='form' action='{0}' method='post'>", postbackUrl); sb.AppendFormat("<input type='hidden' name='t' value='{0}'>", value); sb.Append("</form>"); sb.Append("</body>"); sb.Append("</html>"); Response.Write(sb.ToString()); Response.End(); } } Target Site has function to 1. Get authentication parameters. 2. Validate the parameters with shared secret. 3. If the user is valid, then do authenticate and redirect to target page. 4. If the user is invalid, then show errors and return. using System; using System.Web.Security; using System.Text; public partial class _Default : System.Web.UI.Page { protected void Page_Load(object sender, EventArgs e) { if (!IsPostBack) { if (User.Identity.IsAuthenticated) { Response.Redirect("~/Default.aspx"); } } if (Request.Params.Get("t") != null) { string ticket = Request.Params.Get("t"); char[] delimiters = new char[] { ':', ',' }; string[] ssoVariable = ticket.Split(delimiters, StringSplitOptions.None); string ssoHash = ssoVariable[0]; string ssoTime = ssoVariable[1]; string ssoUserName = ssoVariable[2]; DateTime appTime = DateTime.MinValue; int offsetTime = 60; // get this from config or similar try { appTime = DateTime.ParseExact(ssoTime, "yyyyMMddHHmmss", null); } catch { //show error return; } if (Math.Abs(appTime.Subtract(DateTime.Now).TotalSeconds) > offsetTime) { //show error return; } bool isValid = false; string ssoSharedSecret = "58ag;ai76"; // get this from config or similar string hash = FormsAuthentication.HashPasswordForStoringInConfigFile(string.Format("{0},{1},{2}", ssoSharedSecret, ssoTime, ssoUserName), "md5"); if (string.Compare(ssoHash, hash, true) == 0) { if (Math.Abs(appTime.Subtract(DateTime.Now).TotalSeconds) > offsetTime) { //show error return; } else { isValid = true; } } if (isValid) { //Do authenticate; } else { //show error return; } } else { //show error } } } Summary This is a very simple and basic SSO solution, and its main advantage is its simplicity, only needs to add a single page to do SSO authentication, do not need to modify the existing system infrastructure.

  Read the article

• VS2010 crashes when opening a vsp generated using VS 2012

  - by Tarun Arora

  I recently profiled some web applications using Visual Studio 2012, a vsp (Visual Studio Profile) file was generated as a result of the profiling session. I could successfully open the vsp file in Visual Studio 2012 as expected but when I tried to open the vsp file in Visual Studio 2010 the VS2010 IDE crashed. As a responsible citizen I raised bug # 762202 on Microsoft Connect site using the Microsoft Visual Studio 2012 Feedback Client. Note – In case you didn’t already know, VSP generated in Visual Studio 2012 is not backward compatible. Please refer below for the steps to reproduce the issue and the resolution of the connect bug. 1. Behaviour and Steps to Reproduce the Issue Description I have generated a vsp file by using the Visual Studio 2012 Standalone profiler. When I try and open the vsp file in Visual Studio 2010 the IDE crashes. I understand that a vsp generated by using VS 2012 cannot be opened in VS 2010, but the IDE crashing is not the behaviour I would expect to see. Steps to Reproduce the Issue 1. Pick up the Stand lone profiler from the VS 2012 installation media. The folder has both x 64 and x86 installer, since the machine I am using is x64 bit. I have installed the x64 version of the standalone profiler. 2. I have configured the system path by setting the 'environment variable' path to where the profiler is installed. In my case this is, C:\Program Files (x86)\Microsoft Visual Studio 11.0\Team Tools\Performance Tools 3. Created a new environment variable _NT_SYMBOL_PATH and set its value to CACHE*C:\SYMBOLSCACHE;SRV*C:\SYMBOLSCACHE*HTTP://MSDL.MICROSOFT.COM/DOWNLOAD/SYMBOLS;\\FOO\BUILD1234 4. Open up CMD as an administrator and run 'VSPerfASPNETCmd /tip http://localhost:56180/ /o:C:\Temp\SampleEISK.vsp' 5. This generates the following message on the cmd       Microsoft (R) VSPerf ASP.NET Command, Version 11.0.0.0     Copyright (C) Microsoft Corporation. All rights reserved.     Configuring and attaching to ASP.NET process. Please wait.     Setting up profiling environment.     Starting monitor.     Launching ASP.NET service.     Attaching Monitor to process.     Launching Internet Explorer.     The profiler is attached to ASP.net. Please run your application scenario now.     Press Enter to stop data collection...   6. I perform certain actions and then I come back to the cmd and hit enter to shut down the profiling. Once I do this, the following message is written to the cmd, Press Enter to stop data collection... Profiling now shut down. Report file "C:\Temp\SampleEISK.vsp" was generated. Running VsPerfReport, packing symbols into the .VSP. Shutting down profiling and restarting ASP.NET. Please wait. Restarting w3wp.exe.   7. I look in the C:\Temp folder and I can see the SampleEISK.vsp file generated. I can successfully open this file in Visual Studio 2012. 8. When I am trying to open the vsp file in VS 2010 the VS 2010 IDE crashes. Kaboooom! What I would expect to happen I expect to receive a message "VS 2010 does not support the vsp file generated by VS 2012". What actually happened The VS 2010 IDE crashed 2. Resolution This is a valid bug! However, there isn’t much value in releasing a hotfix for this issue. Refer below to the resolution provided by the Visual Studio Profiler Team.  Thank you for taking the time to report this issue. We completely agree that Visual Studio 2010 should not crash. However in this particular case this is not a bug we are going to retroactively release a fix to 2010 for at this point. Given that a fix would not unblock the scenario of opening a 2012 created file on Visual Studio 2010, and there is not an active update channel for Visual Studio 2010 other than manually locating and installing hot fixes, we will not be fixing this particular issue. Best Regards, Visual Studio Profiler Team   Though it would be great to improve the behaviour however, this is not a defect that would stop you from progressing in any way. It’s important to note however that VSP files generated by Visual Studio 2012 are not backward compatible so you should refrain from opening these files in Visual Studio 2010.

  Read the article

• Web Services Example - Part 2: Programmatic

  - by Denis T

  In this edition of the ADF Mobile blog we'll tackle part 2 of our Web Service examples.  In this posting we'll take a look at using a SOAP Web Service but calling it programmatically in code and parsing the return into a bean. Getting the sample code: Just click here to download a zip of the entire project.  You can unzip it and load it into JDeveloper and deploy it either to iOS or Android.  Please follow the previous blog posts if you need help getting JDeveloper or ADF Mobile installed.  Note: This is a different workspace than WS-Part1 Defining our Web Service: Just like our first installment, we are using the same public weather forecast web service provided free by CDYNE Corporation.  Sometimes this service goes down so please ensure you know it's up before reporting this example isn't working. We're going to concentrate on the same two web service methods, GetCityForecastByZIP and GetWeatherInformation. Defing the Application: The application setup is identical to the Weather1 version.  There are some improvements to the data that is displayed as part of this example though.  Now we are able to show the associated image along with each forecast line when using the Forecast By Zip feature.  We've also added the temperature Hi/Low values into the UI. Summary of Fundamental Changes In This Application The most fundamental change is that we're binding the UI to the Bean Data Controls instead of directly to the Web Service Data Controls.  This gives us much more flexibility to control the shape of the data and allows us to do caching of the data outside of the Web Service.  This way if your application is, say offline, your bean could still populate with data from a local cache and still show you some UI as opposed to completely failing because you don't have any connectivity. In general we promote this type of programming technique with ADF Mobile to insulate your application from any issues with network connectivity. What's different with this example? We have setup the Web Service DC the same way but now we have managed beans to process the data.  The following classes define the "Model" of our application:  CityInformation-CityForecast-Forecast, WeatherInformation-WeatherDescription.  We use WeatherBean for UI interaction to the model layer.  If you look through this example, we don't really do that much with the java code except use it to grab the image URL from the weather description.  In a more realistic example, you might be using some JDBC classes to persist the data to a local database. To have a good architecture it is always good to keep your model and UI layers separate.  This gets muddied if you start to use bindings on a page invoked from Java code and this java code starts to become your "model" layer.  Since bindings are page specific, your model layer starts to become entwined with your UI.  Not good!  To help with this, we've added some utility functions that let you invoke DC methods without having a binding and thus execute methods from your "model" layer without requiring a binding in your page definition.  We do this with the invokeDataControlMethod of the AdfmfJavaUtilities class.  An example of this method call is available in line 95 of WeatherInformation.java and line 93 of CityInformation.Java. What's a GenericType? Because Web Service Data Controls (and also URL Data Controls AKA REST) use generic name/value pairs to define their structure and don't have strongly typed objects, these are actually stored internally as GenericType objects.  The GenericType class is simply a property map of name/value pairs that can be hierarchical.  There are methods like getAttribute where you supply the index of the attribute or it's string property name.  Why is this important to know?  Because invokeDataControlMethod returns GenericType objects and developers either need to parse these GenericType objects themselves or use one of our helper functions. GenericTypeBeanSerializationHelper This class does exactly what it's name implies.  It's a helper class for developers to aid in serialization of GenericTypes to/from java objects.  This is extremely handy if you have a large GenericType object with many attributes (or you're just lazy like me!) and you just want to parse it out into a real java object you can use more easily.  Here you would use the fromGenericType method.  This method takes the class of the Java object you wish to return and the GenericType as parameters.  The method then parses through each attribute in the GenericType and uses reflection to set that same attribute in the Java class.  Then the method returns that new object of the class you specified.  This is obviously very handy to avoid a lot of shuffling code between GenericType and your own Java classes.  The reverse method, toGenericType is also available when you want to go the other way.  In this case you supply the string that represents the package location in the DataControl definition (Example: "MyDC.myParams.MyCollection") and then pass in the Java object you have that holds the data and a GenericType is returned to you.  Again, it will use reflection to calculate the attributes that match between the java class and the GenericType and call the getters/setters on those. Issues and Possible Improvements: In the next installment we'll show you how to make your web service calls asynchronously so your UI will fill dynamically when the service call returns but in the meantime you show the data you have locally in your bean fed from some local cache.  This gives your users instant delivery of some data while you fetch other data in the background.

  Read the article

• ADF Reusable Artefacts

  - by Arda Eralp

  Primary reusable ADF Business Component: Entity Objects (EOs) View Objects (VOs) Application Modules (AMs) Framework Extensions Classes Primary reusable ADF Controller: Bounded Task Flows (BTFs) Task Flow Templates Primary reusable ADF Faces: Page Templates Skins Declarative Components Utility Classes Certain components will often be used more than once. Whether the reuse happens within the same application, or across different applications, it is often advantageous to package these reusable components into a library that can be shared between different developers, across different teams, and even across departments within an organization. In the world of Java object-oriented programming, reusing classes and objects is just standard procedure. With the introduction of the model-view-controller (MVC) architecture, applications can be further modularized into separate model, view, and controller layers. By separating the data (model and business services layers) from the presentation (view and controller layers), you ensure that changes to any one layer do not affect the integrity of the other layers. You can change business logic without having to change the UI, or redesign the web pages or front end without having to recode domain logic. Oracle ADF and JDeveloper support the MVC design pattern. When you create an application in JDeveloper, you can choose many application templates that automatically set up data model and user interface projects. Because the different MVC layers are decoupled from each other, development can proceed on different projects in parallel and with a certain amount of independence. ADF Library further extends this modularity of design by providing a convenient and practical way to create, deploy, and reuse high-level components. When you first design your application, you design it with component reusability in mind. If you created components that can be reused, you can package them into JAR files and add them to a reusable component repository. If you need a component, you may look into the repository for those components and then add them into your project or application. For example, you can create an application module for a domain and package it to be used as the data model project in several different applications. Or, if your application will be consuming components, you may be able to load a page template component from a repository of ADF Library JARs to create common look and feel pages. Then you can put your page flow together by stringing together several task flow components pulled from the library. An ADF Library JAR contains ADF components and does not, and cannot, contain other JARs. It should not be confused with the JDeveloper library, Java EE library, or Oracle WebLogic shared library. Reusable Component Description Data Control Any data control can be packaged into an ADF Library JAR. Some of the data controls supported by Oracle ADF include application modules, Enterprise JavaBeans, web services, URL services, JavaBeans, and placeholder data controls. Application Module When you are using ADF Business Components and you generate an application module, an associated application module data control is also generated. When you package an application module data control, you also package up the ADF Business Components associated with that application module. The relevant entity objects, view objects, and associations will be a part of the ADF Library JAR and available for reuse. Business Components Business components are the entity objects, view objects, and associations used in the ADF Business Components data model project. You can package business components by themselves or together with an application module. Task Flows & Task Flow Templates Task flows can be packaged into an ADF Library JAR for reuse. If you drop a bounded task flow that uses page fragments, JDeveloper adds a region to the page and binds it to the dropped task flow. ADF bounded task flows built using pages can be dropped onto pages. The drop will create a link to call the bounded task flow. A task flow call activity and control flow will automatically be added to the task flow, with the view activity referencing the page. If there is more than one existing task flow with a view activity referencing the page, it will prompt you to select the one to automatically add a task flow call activity and control flow. If an ADF task flow template was created in the same project as the task flow, the ADF task flow template will be included in the ADF Library JAR and will be reusable. Page Templates You can package a page template and its artifacts into an ADF Library JAR. If the template uses image files and they are included in a directory within your project, these files will also be available for the template during reuse. Declarative Components You can create declarative components and package them for reuse. The tag libraries associated with the component will be included and loaded into the consuming project. You can also package up projects that have several different reusable components if you expect that more than one component will be consumed. For example, you can create a project that has both an application module and a bounded task flow. When this ADF Library JAR file is consumed, the application will have both the application module and the task flow available for use. You can package multiple components into one JAR file, or you can package a single component into a JAR file. Oracle ADF and JDeveloper give you the option and flexibility to create reusable components that best suit you and your organization. You create a reusable component by using JDeveloper to package and deploy the project that contains the components into a ADF Library JAR file. You use the components by adding that JAR to the consuming project. At design time, the JAR is added to the consuming project's class path and so is available for reuse. At runtime, the reused component runs from the JAR file by reference.

  Read the article

• OIM 11g - Multi Valued attribute reconciliation of a child form

  - by user604275

  This topic gives a brief description on how we can do reconciliation of a child form attribute which is also multi valued from a flat file . The format of the flat file is (an example): ManagementDomain1|Entitlement1|DIRECTORY SERVER,EMAIL ManagementDomain2|Entitlement2|EMAIL PROVIDER INSTANCE - UMS,EMAIL VERIFICATION In OIM there will be a parent form for fields Management domain and Entitlement.Reconciliation will assign Servers ( which are multi valued) to corresponding Management  Domain and Entitlement .In the flat file , multi valued fields are seperated by comma(,). In the design console, Create a form with 'Server Name' as a field and make it a child form . Open the corresponding Resource Object and add this field for reconcilitaion.While adding , choose 'Multivalued' check box. (please find attached screen shot on how to add it , Child Table.docx) Open process definiton and add child form fields for recociliation. Please click on the 'Create Reconcilitaion Profile' buttton on the resource object tab. The API methods used for child form reconciliation are : 1.           reconEventKey =   reconOpsIntf.createReconciliationEvent(resObjName, reconData,                                                            false); ·                                    ‘False’  here tells that we are creating the recon for a child table . 2.               2.       reconOpsIntf.providingAllMultiAttributeData(reconEventKey, RECON_FIELD_IN_RO, true);                RECON_FIELD_IN_RO is the field that we added in the Resource Object while adding for reconciliation, please refer the screen shot) 3.    reconOpsIntf.addDirectBulkMultiAttributeData(reconEventKey,RECON_FIELD_IN_RO, bulkChildDataMapList);                 bulkChildDataMapList  is coded as below :                 List<Map> bulkChildDataMapList = new ArrayList<Map>();                   for (int i = 0; i < stokens.length; i++) {                            Map<String, String> attributeMap = new HashMap<String, String>();                           String serverName = stokens[i].toUpperCase();                           attributeMap.put("Server Name", stokens[i]);                           bulkChildDataMapList.add(attributeMap);                         } 4                  4.       reconOpsIntf.finishReconciliationEvent(reconEventKey); 5.       reconOpsIntf.processReconciliationEvent(reconEventKey); Now, we have to register the plug-in, import metadata into MDS and then create a scheduled job to execute which will run the reconciliation.

  Read the article

• Getting Started with ADF Mobile Sample Apps

  - by Denis T

  Getting Started with ADF Mobile Sample Apps   Installation Steps Install JDeveloper 11.1.2.3.0 from Oracle Technology Network After installing JDeveloper, go to Help menu and select "Check For Updates" and find the ADF Mobile extension and install this. It will require you restart JDeveloper For iOS development, be on a Mac and have Xcode installed. (Currently only Xcode 4.4 is officially supported. Xcode 4.5 support is coming soon) For Android development, have the Android SDK installed. In the JDeveloper Tools menu, select "Preferences". In the Preferences dialog, select ADF Mobile. You can expand it to select configure your Platform preferences for things like the location of Xcode and the Android SDK. In your /jdeveloper/jdev/extensions/oracle.adf.mobile/Samples folder you will find a PublicSamples.zip. Unzip this into the Samples folder so you have all the projects ready to go. Open each of the sample application's .JWS file to open the corresponding workspace. Then from the "Application" menu, select "Deploy" and then select the deployment profile for the platform you wish to deploy to. Try deploying to the simulator/emulator on each platform first because it won't require signing. Note: If you wish to deploy to the Android emulator, it must be running before you start the deployment.   Sample Application Details   Recommended Order of Use Application Name Description 1 HelloWorld The "hello world" application for ADF Mobile, which demonstrates the basic structure of the framework. This basic application has a single application feature that is implemented with a local HTML file. Use this application to ascertain that the development environment is set up correctly to compile and deploy an application. See also Section 4.2.2, "What Happens When You Create an ADF Mobile Application." 2 CompGallery This application is meant to be a runtime application and not necessarily to review the code, though that is available. It serves as an introduction to the ADF Mobile AMX UI components by demonstrating all of these components. Using this application, you can change the attributes of these components at runtime and see the effects of those changes in real time without recompiling and redeploying the application after each change. See generally Chapter 8, "Creating ADF Mobile AMX User Interface." 3 LayoutDemo This application demonstrates the user interface layout and shows how to create the various list and button styles that are commonly used in mobile applications. It also demonstrates how to create the action sheet style of a popup component and how to use various chart and gauge components. See Section 8.3, "Creating and Using UI Components" and Section 8.5, "Providing Data Visualization." Note: This application must be opened from the Samples directory or the Default springboard option must be cleared in the Applications page of the adfmf-application.xml overview editor, then selected again. 4 JavaDemo This application demonstrates how to bind the user interface to Java beans. It also demonstrates how to invoke EL bindings from the Java layer using the supplied utility classes. See also Section 8.10, "Using Event Listeners" and Section 9.2, "Understanding EL Support." 5 Navigation This application demonstrates the various navigation techniques in ADF Mobile, including bounded task flows and routers. It also demonstrates the various page transitions. See also Section 7.2, "Creating Task Flows." Note: This application must be opened from the Samples directory or the Default springboard option must be cleared in the Applications page of the adfmf-application.xml overview editor, then selected again. 6 LifecycleEvents This application implements lifecycle event handlers on the ADF Mobile application itself and its embedded application features. This application shows you where to insert code to enable the applications to perform their own logic at certain points in the lifecycle. See also Section 5.6, "About Lifecycle Event Listeners." Note: iOS, the LifecycleEvents sample application logs data to the Console application, located at Applications-Utilities-Console application. 7 DeviceDemo This application shows you how to use the DeviceFeatures data control to expose such device features as geolocation, e-mail, SMS, and contacts, as well as how to query the device for its properties. See also Section 9.5, "Using the DeviceFeatures Data Control." Note: You must also run this application on an actual device because SMS and some of the device properties do not function on an iOS simulator or Android emulator. 8 GestureDemo This application demonstrates how gestures can be implemented and used in ADF Mobile applications. See also Section 8.4, "Enabling Gestures." 9 StockTracker This application demonstrates how data change events use Java to enable data changes to be reflected in the user interface. It also has a variety of layout use cases, gestures and basic mobile patterns. See also Section 9.7, "Data Change Events."

  Read the article

• Can't control connection bit rate using iwconfig with Atheros TL-WN821N (AR7010)

  - by Paul H

  I'm trying to reduce the connection bit rate on my Atheros TP-Link TL-WN821N v3 usb wifi adapter due to frequent instability issues (reported connection speed goes down to 1Mb/s and I have to physically reconnect the adapter to regain a connection). I know this is a common problem with this device, and I have tried everything I can think of to fix it, including using drivers from linux-backports; compiling and installing a custom firmware (following instructions on https://wiki.debian.org/ath9k_htc#fw-free) and (as a last resort) using ndiswrapper. When using ndiswrapper, the wifi adapter is stable and operates in g mode at 54Mb/s (whilst when using the default ath9k_htc module, the adapter connects in n mode and the bit rate fluctuates constantly). Unfortunately, with this setup I have to run my processor using only one core, since using SMP with ndiswrapper causes a kernel oops on my system. So I want to lock my bit rate to 54Mb/s (or less, if need be) for connection stability, using the ath9k_htc module. I've tried 'sudo iwconfig wlan0 rate 54M'; the command runs with no error but when I check the bit rate with 'sudo iwlist wlan0 bitrate' the command returns: wlan0 unknown bit-rate information. Current Bit Rate:78 Mb/s Any ideas? Here's some info (hopefully relevant) on my setup: Xubuntu (12.04.3) 64bit (kernel 3.2.0-55.85-generic) using Network Manager. My Router is from Virgin Media, the VMDG480. lshw -C network : *-network description: Wireless interface physical id: 1 bus info: usb@1:4 logical name: wlan0 serial: 74:ea:3a:8f:16:b6 capabilities: ethernet physical wireless configuration: broadcast=yes driver=ath9k_htc driverversion=3.2.0-55 firmware=1.3 ip=192.168.0.9 link=yes multicast=yes wireless=IEEE 802.11bgn lsusb -v: Bus 001 Device 003: ID 0cf3:7015 Atheros Communications, Inc. TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287] Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 255 Vendor Specific Class bDeviceSubClass 255 Vendor Specific Subclass bDeviceProtocol 255 Vendor Specific Protocol bMaxPacketSize0 64 idVendor 0x0cf3 Atheros Communications, Inc. idProduct 0x7015 TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287] bcdDevice 2.02 iManufacturer 16 ATHEROS iProduct 32 UB95 iSerial 48 12345 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 60 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 500mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 6 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 0 bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x04 EP 4 OUT bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x05 EP 5 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x06 EP 6 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 255 Vendor Specific Class bDeviceSubClass 255 Vendor Specific Subclass bDeviceProtocol 255 Vendor Specific Protocol bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0000 (Bus Powered) iwlist wlan0 scanning: wlan0 Scan completed : Cell 01 - Address: C4:3D:C7:3A:1F:5D Channel:1 Frequency:2.412 GHz (Channel 1) Quality=37/70 Signal level=-73 dBm Encryption key:on ESSID:"my essid" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s Mode:Master Extra:tsf=00000070cca77186 Extra: Last beacon: 5588ms ago IE: Unknown: 0007756E69636F726E IE: Unknown: 010882848B962430486C IE: Unknown: 030101 IE: Unknown: 2A0100 IE: Unknown: 2F0100 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: 32040C121860 IE: Unknown: 2D1AFC181BFFFF000000000000000000000000000000000000000000 IE: Unknown: 3D1601080400000000000000000000000000000000000000 IE: Unknown: DD7E0050F204104A0001101044000102103B00010310470010F99C335D7BAC57FB00137DFA79600220102100074E657467656172102300074E6574676561721024000631323334353610420007303030303030311054000800060050F20400011011000743473331303144100800022008103C0001011049000600372A000120 IE: Unknown: DD090010180203F02C0000 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00 iwconfig: lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"my essid" Mode:Managed Frequency:2.412 GHz Access Point: C4:3D:C7:3A:1F:5D Bit Rate=78 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=36/70 Signal level=-74 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0,

  Read the article

• What's New in Oracle VM VirtualBox 4.2?

  - by Fat Bloke

  A year is a long time in the IT industry. Since the last VirtualBox feature release, which was a little over a year ago, we've seen: new releases of cool new operating systems, such as Windows 8, ChromeOS, and Mountain Lion; we've seen a myriad of new Linux releases from big Enterprise class distributions like Oracle 6.3, to accessible desktop distros like Ubuntu 12.04 and Fedora 17; and we've also seen the spec of a typical PC or laptop double in power. All of these events have influenced our new VirtualBox version which we're releasing today. Here's how... Powerful hosts  One of the trends we've seen is that as the average host platform becomes more powerful, our users are consistently running more and more vm's. Some of our users have large libraries of vm's of various vintages, whilst others have groups of vm's that are run together as an assembly of the various tiers in a multi-tiered software solution, for example, a database tier, middleware tier, and front-ends.  So we're pleased to unveil a more powerful VirtualBox Manager to address the needs of these users: VM Groups Groups allow you to organize your VM library in a sensible way, e.g.  by platform type, by project, by version, by whatever. To create groups you can drag one VM onto another or select one or more VM's and choose Machine...Group from the menu bar. You can expand and collapse groups to save screen real estate, and you can Enter and Leave a group (think iPad navigation here) by using the right and left arrow keys when groups are selected. But groups are more than passive folders, because you can now also perform operations on groups, rather than all the individual VMs. So if you have a multi-tiered solution you can start the whole stack up with just one click. Autostart Many VirtualBox users run dedicated services in their VMs, for example, running a Wiki. With these types of VM workloads, you really want the VM start up when the host machine boots up. So with 4.2 we've introduced a cross-platform Auto-start mechanism to allow you to treat VMs as host services. Headless VM Launching With VM's such as web servers, wikis, and other types of server-class workloads, the Console of the VM is pretty much redundant. For some time now VirtualBox has offered a separate launch mechanism for these VM's, namely the command-line interface commands VBoxHeadless or VBoxManage startvm ... --type headless commands. But with 4.2 we also allow you launch headless VMs from the Manager. Simply hold down Shift when launching the VM from the Manager.  It's that easy. But how do you stop a headless VM? Well, with 4.2 we allow you to Close the VM from the Manager. (BTW best to use the ACPI Shutdown method which allows the guest VM to close down gracefully.) Easy VM Creation For our expert users, the  New VM Wizard was a little tiresome, so now there's a faster 2-click VM creation mode. Just Hide the description when creating a new VM. Powerful VMs  As the hosts have become more powerful, so are the guests that are running inside them. Here are some of the 4.2 features to accommodate them: Virtual Network Interface Cards  With 4.2, it's now possible to create VMs with up to 36 NICs, when using the ICH9 chipset emulation. But with great power comes great responsibility (didn't Obi-Wan say something similar?), and so we have also introduced bandwidth limiting to prevent a rogue VM stealing the whole pipe. VLAN tagging Some of our users leverage VLANs extensively so we've enhanced the E1000 NICs to support this.  Processor Performance If you are running a CPU which supports Nested Paging (aka EPT in the Intel world) such as most of the Core i5 and i7 CPUs, or are running an AMD Bulldozer or later, you should see some performance improvements from our work with these processors. And while we're talking Processors, we've added support for some of the more modern VIA CPUs too. Powerful Automation Because VirtualBox runs atop a fully blown operating system, it makes sense to leverage the capabilities of the host to run scripts that can drive the guest VMs. Guest Automation was introduced in a prior release but with 4.2 we've revamped the APIs to allow a richer and more powerful set of operations to be executed by the guest. Check out the IGuest APIs in the VirtualBox Programming Guide and Reference (SDK). Powerful Platforms  All the hardcore engineering that has gone into 4.2 has been done for a purpose and that is to deliver a fast and powerful engine that can run almost any x86 OS because of the integrity of the virtualization. So we're pleased to add support for these platforms: Mac OS X "Mountain Lion"  Windows 8 Windows Server 2012 Ubuntu 12.04 (“Precise Pangolin”) Fedora 17 Oracle Linux 6.3  Here's the proof: We don't have time to go into the myriad of smaller improvements such as support for burning audio CDs from a guest, bi-directional clipboard control,  drag-and-drop of files into Linux guests, etc. so we'll leave that as an exercise for the user as soon as you've downloaded from the Oracle or community site and taken a peek at the User Guide. So all in all, a pretty solid release, one that we hope you'll enjoy discovering. - FB 

  Read the article

• Deadlock Analysis in NetBeans 8

  - by Geertjan

  Lock contention profiling is very important in multi-core environments. Lock contention occurs when a thread tries to acquire a lock while another thread is holding it, forcing it to wait. Lock contentions result in deadlocks. Multi-core environments have even more threads to deal with, causing an increased likelihood of lock contentions. In NetBeans 8, the NetBeans Profiler has new support for displaying detailed information about lock contention, i.e., the relationship between the threads that are locked. After all, whenever there's a deadlock, in any aspect of interaction, e.g., a political deadlock, it helps to be able to point to the responsible party or, at least, the order in which events happened resulting in the deadlock. As an example, let's take the handy Deadlock sample code from the Java Tutorial and look at the tools in NetBeans IDE for identifying and analyzing the code. The description of the deadlock is nice: Alphonse and Gaston are friends, and great believers in courtesy. A strict rule of courtesy is that when you bow to a friend, you must remain bowed until your friend has a chance to return the bow. Unfortunately, this rule does not account for the possibility that two friends might bow to each other at the same time. To help identify who bowed first or, at least, the order in which bowing took place, right-click the file and choose "Profile File". In the Profile Task Manager, make the choices below: When you have clicked Run, the Threads window shows the two threads are blocked, i.e., the red "Monitor" lines tell you that the related threads are blocked while trying to enter a synchronized method or block: But which thread is holding the lock? Which one is blocked by the other? The above visualization does not answer these questions. New in NetBeans 8 is that you can analyze the deadlock in the new Lock Contention window to determine which of the threads is responsible for the lock: Here is the code that simulates the lock, very slightly tweaked at the end, where I use "setName" on the threads, so that it's even easier to analyze the threads in the relevant NetBeans tools. Also, I converted the anonymous inner Runnables to lambda expressions. package org.demo; public class Deadlock { static class Friend { private final String name; public Friend(String name) { this.name = name; } public String getName() { return this.name; } public synchronized void bow(Friend bower) { System.out.format("%s: %s" + " has bowed to me!%n", this.name, bower.getName()); bower.bowBack(this); } public synchronized void bowBack(Friend bower) { System.out.format("%s: %s" + " has bowed back to me!%n", this.name, bower.getName()); } } public static void main(String[] args) { final Friend alphonse = new Friend("Alphonse"); final Friend gaston = new Friend("Gaston"); Thread t1 = new Thread(() -> { alphonse.bow(gaston); }); t1.setName("Alphonse bows to Gaston"); t1.start(); Thread t2 = new Thread(() -> { gaston.bow(alphonse); }); t2.setName("Gaston bows to Alphonse"); t2.start(); } } In the above code, it's extremely likely that both threads will block when they attempt to invoke bowBack. Neither block will ever end, because each thread is waiting for the other to exit bow. Note: As you can see, it really helps to use "Thread.setName", everywhere, wherever you're creating a Thread in your code, since the tools in the IDE become a lot more meaningful when you've defined the name of the thread because otherwise the Profiler will be forced to use thread names like "thread-5" and "thread-6", i.e., based on the order of the threads, which is kind of meaningless. (Normally, except in a simple demo scenario like the above, you're not starting the threads in the same class, so you have no idea at all what "thread-5" and "thread-6" mean because you don't know the order in which the threads were started.) Slightly more compact: Thread t1 = new Thread(() -> { alphonse.bow(gaston); },"Alphonse bows to Gaston"); t1.start(); Thread t2 = new Thread(() -> { gaston.bow(alphonse); },"Gaston bows to Alphonse"); t2.start();

  Read the article

< Previous Page | 225 226 227 228 229 230 231 232 233 234 235 236  | Next Page >