Search Results

Search found 1425 results on 57 pages for 'cisco catalyst'.

Page 23/57 | < Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >

• Spanning-tree setup with incompatible switches

  - by wfaulk

  I have a set of eight HP ProCurve 2910al-48G Ethernet switches at my datacenter that are set up in a star topology with no physical loops. I want to partially mesh the switches for redundancy and manage the loops with a spanning-tree protocol. However, our connection to the datacenter is provided by two uplinks, each to a Cisco 3750. The datacenter's switches are handling the redundant connection using PVST spanning-tree, which is a Cisco-proprietary spanning-tree implementation that my HP switches do not support. It appears that my switches are not participating in the datacenter's spanning-tree domain, but are blindly passing the BPDUs between the two switchports on my side, which enables the datacenter's switches to recognize the loop and put one of the uplinks into the Blocking state. This is somewhat supposition, but I can confirm that, while my switches say that both of the uplink ports are forwarding, only one is passing any real quantity of data. (I am assuming that I cannot get the datacenter to move away from PVST. I don't know that I'd want them to make that significant of a change anyway.) The datacenter has also sent me this output from their switches (which I have expurgated of any identifiable info): 3750G-1#sh spanning-tree vlan nnn VLAN0nnn Spanning tree enabled protocol ieee Root ID Priority 10 Address 00d0.0114.xxxx Cost 4 Port 5 (GigabitEthernet1/0/5) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32mmm (priority 32768 sys-id-ext nnn) Address 0018.73d3.yyyy Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 300 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Gi1/0/5 Root FWD 4 128.5 P2p Gi1/0/6 Altn BLK 4 128.6 P2p Gi1/0/8 Altn BLK 4 128.8 P2p and: 3750G-2#sh spanning-tree vlan nnn VLAN0nnn Spanning tree enabled protocol ieee Root ID Priority 10 Address 00d0.0114.xxxx Cost 4 Port 6 (GigabitEthernet1/0/6) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32mmm (priority 32768 sys-id-ext nnn) Address 000f.f71e.zzzz Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 300 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Gi1/0/1 Desg FWD 4 128.1 P2p Gi1/0/5 Altn BLK 4 128.5 P2p Gi1/0/6 Root FWD 4 128.6 P2p Gi1/0/8 Desg FWD 4 128.8 P2p The uplinks to my switches are on Gi1/0/8 on both of their switches. The uplink ports are configured with a single tagged VLAN. I am also using a number of other tagged VLANs in my switch infrastructure. And, to be clear, I am passing the tagged VLAN I'm receiving from the datacenter to other ports on other switches in my infrastructure. My question is: how do I configure my switches so that I can use a spanning tree protocol inside my switch infrastructure without breaking the datacenter's spanning tree that I cannot participate in?

  Read the article

• Why is port 444 open on this router?

  - by TJ Thind

  I have a Cisco RV110W. I ran nmap at it from the outside and nmap reports that the router has tcp port 444 open. Yet there are no port forwarding rules specifying this port. It should as far as I can tell, be closed. There's even a service listening to that port which I can connect to through telnet. I threw some SNPP commands at it but the service doesn't respond to any of them so I don't believe it's SNPP. Does anyone have any idea why this particular router has tcp port 444 open? I haven't been able to find anything in the manual or on Cisco's website.

  Read the article

• Need help making site available externally

  - by White Island

  I'm trying to open a hole in the firewall (ASA 5505, v8.2) to allow external access to a Web application. Via ASDM (6.3?), I've added the server as a Public Server, which creates a static NAT entry [I'm using the public IP that is assigned to 'dynamic NAT--outgoing' for the LAN, after confirming on the Cisco forums that it wouldn't bring everyone's access crashing down] and an incoming rule "any... public_ip... https... allow" but traffic is still not getting through. When I look at the log viewer, it says it's denied by access-group outside_access_in, implicit rule, which is "any any ip deny" I haven't had much experience with Cisco management. I can't see what I'm missing to allow this connection through, and I'm wondering if there's anything else special I have to add. I tried adding a rule (several variations) within that access-group to allow https to the server, but it never made a difference. Maybe I haven't found the right combination? :P I also made sure the Windows firewall is open on port 443, although I'm pretty sure the current problem is Cisco, because of the logs. :) Any ideas? If you need more information, please let me know. Thanks Edit: First of all, I had this backward. (Sorry) Traffic is being blocked by access-group "inside_access_out" which is what confused me in the first place. I guess I confused myself again in the midst of typing the question. Here, I believe, is the pertinent information. Please let me know what you see wrong. access-list acl_in extended permit tcp any host PUBLIC_IP eq https access-list acl_in extended permit icmp CS_WAN_IPs 255.255.255.240 any access-list acl_in remark Allow Vendor connections to LAN access-list acl_in extended permit tcp host Vendor any object-group RemoteDesktop access-list acl_in remark NetworkScanner scan-to-email incoming (from smtp.mail.microsoftonline.com to PCs) access-list acl_in extended permit object-group TCPUDP any object-group Scan-to-email host NetworkScanner object-group Scan-to-email access-list acl_out extended permit icmp any any access-list acl_out extended permit tcp any any access-list acl_out extended permit udp any any access-list SSLVPNSplitTunnel standard permit LAN_Subnet 255.255.255.0 access-list nonat extended permit ip VPN_Subnet 255.255.255.0 LAN_Subnet 255.255.255.0 access-list nonat extended permit ip LAN_Subnet 255.255.255.0 VPN_Subnet 255.255.255.0 access-list inside_access_out remark NetworkScanner Scan-to-email outgoing (from scanner to Internet) access-list inside_access_out extended permit object-group TCPUDP host NetworkScanner object-group Scan-to-email any object-group Scan-to-email access-list inside_access_out extended permit tcp any interface outside eq https static (inside,outside) PUBLIC_IP LOCAL_IP[server object] netmask 255.255.255.255 I wasn't sure if I needed to reverse that "static" entry, since I got my question mixed up... and also with that last access-list entry, I tried interface inside and outside - neither proved successful... and I wasn't sure about whether it should be www, since the site is running on https. I assumed it should only be https.

  Read the article

• Force10 S60 remote management

  - by StaringSkyward

  We've got a Force10 S60 switch to replace an older Cisco. I can't find a way to give the switch itself an IP address on the local VLAN so I can ssh to it. The config guide talks about using either a management interface on a separate management network or dedicating e.g. a gigabit port as a management port with a dedicated IP address. Ideally I would like to do what we do currently with the Cisco switches, which is in effect give the entire switch an IP so it can be reached from any host on the same VLAN without having to use up a physical port on the switch or physically connect the management port to another device. Is this possible with the S60 and if so, how would you give it, say the address 10.0.1.1 in vlan 10 (10.0.1.1/24)? Thanks!!!

  Read the article

• Virtualization deployment for datacenter

  - by bogha

  Hi, my company is going to deploy an IT Infrastructure on a virtual platform, can you please help me with the following: 1- which one do you recommend, Cisco Unified computing system ( cisco + emc + vmware )or HP Blades( virtualization solution + HP Storage )? 2- i Need to install a DNS Server, Web server, cpanel for managing hosting packages and Microsoft layer of product for usingg in the corporate infrastructur ( active directory, Local DNS, Exchange server, DHCP, Global catalog ) what is the minimum requirments for these servers ( in terms of CPU and Memory ) . 3- what is the best way to implement a redundant solution in a virtual environment. thank you

  Read the article

• How to assign single port into multiple vlans

  - by maroof Qadri

  Hi.. I have cisco switch 3560 and want to create vlans where in i can have a single port in multiple vlans. I tried creating one port e.g fa0/23 as trunk and then allowed it through multiple vlans but it doesnt work. The said port fa0/23 is not traceable through vlans. Example of what i am looking to establish. Vlan 1 : fa0/1 , fa0/2 , fa0/23 vlan 2 : fa0/3, fa0/4,fa0/23 vlan 3 : fa0/5,fa0/6,fa0/23 The Switchport multi command is not working on this switch which i always execute on cisco catalys 3500xl

  Read the article

• Are VLANs necessary for my environment?

  - by kleefaj

  Greetings. I'm the new network manager for a school. I've inherited an environment made up of several Windows servers, about 100 Windows clients, ten printers, one Cisco router, six Cisco switches, and 1 HP switch. Also, we're using VoIP. There are four floors in our building. The hosts on each floor are assigned to a separate VLAN. An office on the first floor has its own VLAN. All the switches are on their own VLAN. The IP phones are on their own VLAN. And the servers are on their own VLAN. For the number of hosts on the network, are all these VLANs really buying me anything? I'm new to the VLAN concept but it seems overly complicated for this environment. Or it's genius and I just don't get it. Any thoughts? Thanks, Jeff

  Read the article

• port forwarding using 3 static ip addresses

  - by Danny

  I am new to configuring routers. We have purchased a RV016 Cisco business router that has multiwan capability. What we are attempting to do is take map services from 3 different servers and assign 3 different static IP addresses and then forward port 80 through the router. A short term solution to building a proxy server. Is this possible? Right now we have a consumer grade Cisco router and assign a static IP and it works, we attempted the same settings on the business router and cannot get to the internet. We set it DHCP and it works fine, however we want to to forward the static ports not use DHCP.

  Read the article

• Windows XP clients do not update server 2008 DNS forward lookup zone.

  - by whatsisname

  I have a Cisco 5505 working as a DHCP server, and a server 2008 DNS server running an AD domain. I am having problems with all XP computers not updating the forward lookup zone. The reverse lookup zone updates are working. Windows vista and 7 computers update just fine. Additionally the DNS server accepts both secure and non-secure updates. When people are connected through the Cisco's VPN, they cannot resolve to any machines that have reverse lookup zones, but they can resolve entries in the forward lookup zone. I have tried ipconfig /registerdns, but the forward lookup zone entries for the XP clients are not being populated. How can I get the XP Dynamic DNS client to make the updates, or what can I do to debug what's going on? Thanks

  Read the article

• How do I install the Cisco Anyconnect VPN client?

  - by chuck

  I installed Cisco AnyConnect for Ubuntu(64) 12.04, but it failed. It can be installed on Ubuntu 10.10(64). The error log Installing Cisco AnyConnect VPN Client ... Extracting installation files to /tmp/vpn.teuSIr/vpninst096243274.tgz... Unarchiving installation files to /tmp/vpn.teuSIr... Starting the VPN agent... /opt/cisco/vpn/bin/vpnagentd: error while loading shared libraries: libxml2.so.2: cannot open shared object file: No such file or directory When I meet that, locate libxml2.so.2 /usr/lib/x86_64-linux-gnu/libxml2.so.2 /usr/lib/x86_64-linux-gnu/libxml2.so.2.7.8 So I create symbol link libxml2.so.2 in /user/lib and after I do: Installing Cisco AnyConnect VPN Client ... Extracting installation files to /tmp/vpn.5cz4FV/vpninst001442979.tgz... Unarchiving installation files to /tmp/vpn.5cz4FV... Starting the VPN agent... /opt/cisco/vpn/bin/vpnagentd: error while loading shared libraries: libxml2.so.2: wrong ELF class: ELFCLASS64 I ensure that there exist lib32 runtime lib on my device. How can I fix this?

  Read the article

• How to play games in widescreen in Windows 7, Dell Studio 1555

  - by blasteralfred

  I have a dell studio 1555 laptop with a GPU inside. The details are below; Hardware details Software details I can play games in widescreen in Vista, but not in 7. I am using Windows 7 Home Premium. I have the latest Catalyst Control Center. Instead of widescreen, the games are running in a classic style, say 1024x768 ratio. When I play need for speed underground, the maximum possible resolution is 1024x768 (all other games are like this). I have no problem with HD videos and anything else. How can I fix this? Thanks in advance...:)

  Read the article

• How do I hookup a dual video card Crossfire rig to a single monitor?

  - by Alexed

  I just received a new Alienware box preinstalled with two nice shiny ATI 6950 graphics cards. My goal is to use both of them to give me really good resolution and frame rate on my single monitor. There's zero documentation with the Alienware box and nothing I can find online. Do I just plug the monitor into one of the cards, and expect the two cards to do magic internally? The ATI Crossfire website indicates a need for an "external crossfirex connection cable". Do I need to buy one of these? If so, what kind of cable is it? The AMD Catalyst Control Center shows the second card as "Linked" but when I go to the AMD Overdrive section, the second card is at zero temperature, and clock, suggesting it's not actually doing anything. What do I need to do to make use of both cards? Is it something that doesn't kick in until I do something graphically intensive?

  Read the article

• Encryption over gigabit carrier ethernet

  - by Roy

  I would like to encrypt traffic between two data centres. Communication between the sites is provided as a standard provider bridge (s-vlan/802.1ad), so that our local vlan tags (c-vlan/802.1q) are preserved on the trunk. The communication traverse several layer 2 hops in the provider network. Border switches on both sides are Catalyst 3750-X with the MACSec service module, but I assume MACSec is out of the question, as I don't see any way to ensure L2 equality between the switches over a trunk, although it may be possible over a provider bridge. MPLS (using EoMPLS) would certainly allow this option, but is not available in this case. Either way, equipment can always be replaced to accommodate technology and topology choices. How do I go about finding viable technology options that can provide layer 2 point-to-point encryption over ethernet carrier networks?

  Read the article

• Prevent Cisco VPN from interrupting home networking

  - by jkohlhepp

  I just got a new laptop, and for the most part have left its settings alone. Today I was trying to get some sharing going between my desktop and the laptop. Both machines are connected to the same wireless network and both machines consider that network to be a Home network. Both are running Win7 Home Premium. It seems like my laptop is aware of my desktop on the network. It can ping it by IP or by computer name. When I go to Network from the laptop, I can see the desktop in the list of computers. However, my desktop cannot ping the laptop, nor can it see it within Network. My desktop has a Homegroup set up, but my laptop says "There is currently no homegroup on the network". I do have network discovery turned on for both machines. Why can my desktop not "talk" to my laptop but it works the other way around? Update: Disabling the Windows Firewall on the laptop somewhat fixes the problem. With it disabled, my desktop can ping my laptop, but still my laptop can't see the homegroup. Also, it can ping via hostname, which resolves to IPv6, but can't ping via the IPv4 address. Obviously I'd rather not leave my firewall disabled, so I need a more specific fix. Update 2: Aha! It is the Cisco VPN software I was running to connect to work computers. Once I disconnected and exited from that, the two PCs seemed to be talking normally and the homegroup was visible to the laptop. So now my question has morphed: how can I prevent Cisco VPN from interrupting my home networking?

  Read the article

• Linksys/Cisco Small Business SRW-Series (ie SRW248G4) - Overcoming the Limitations

  - by Warren P

  We just purchased a Cisco/Linksys SRW 248G4 switch to try it out. We have always had unmanaged switches before, and this is our first "somewhat managed" switch. So far the major limitations are: Only Internet Explorer 6 (manual says IE 5.5!) works for the web interface SSH exists but is not practically useable because the only key length that is supported is no longer even used by most modern SSH installs. (I get the error "RSA modulus too small" in openssh 4.x/5.x) This is with the latest firmware revision, I believe, although Cisco's website does not actually tell you what version you're downloading. All in all, I think, they must be trying to tell me that if I want a good-quality switch, I shouldn't buy these SRWs and should buy a Dell or an HP ProCurve, or save up my pennies, and buy a Catalyst. The question here, then, at long last: Has anyone gotten the web-browser to work via some IE 7 or IE 8 compatibility mode settings or used another browser (Opera? KDE/Safari/WebKit?) and spoofed IE6? Is there any way to get the SSH key length upgraded? I'm guessing a 0% chance of a yes on that last one. I found an XP machine, used telnet (via PuttyTel.exe) and IE6 to set this up, and I doubt we'll have to touch it again. Which is fine with us. But it would be nice if I could administer this thing from either (a) a linux box, or (b) my primary desktop which is windows 7. It looks like XPMode with IE6 on the virtual XP machine may be my only way to administer this type of switch via the web.

  Read the article

• DNS Resolution doesn't work after uninstalling Cisco VPN & Deterministic Network Enhancer in Win 7

  - by Craig M

  I just upgraded my home PC to Windows 7 Ultimate 32 bit. After trying various methods to get the Cisco VPN client to work, I gave up and decided to just run it in XP mode. The last steps I tried were in this article ( http://social.technet.microsoft.com/Forums/en-US/w7itproappcompat/thread/d880dfe5-7f44-4955-8620-2a9355d8ea8b/ ) After that, I uninstalled the Cisco client and rebooted. I uninstalled the Deterministic Network Enhancer and rebooted again. Both uninstalled successfully, but now I'm not able to resolve any DNS. The only way I can resolve DNS is to reinstall the DNE, reboot, and uninstall the DNE. Then I am able to resolve DNS lookups until I reboot again. Once it's rebooted, no more DNS. Any ideas? Edit: I completely forgot I'd asked this question until harrymc posted his answer. I've since found out that to fix this problem, I need to disable my Local Area Connection and re-enable it. Once I do that I have no trouble making network connections until the next time I reboot at which point I repeat the process. It's annoying, but manageable since I reboot very infrequently.

  Read the article

• How to verify system using right GPU, after system reset [duplicate]

  - by Antoros

  This question already has an answer here: Is my mobile AMD card being used? 2 answers OS: Windows 8 CPU: Intel® Core™ i7 Processor 3635QM GPU 1 : Intel HD Graphics 4000 GPU 2 : AMD Radeon™ HD 8870M other info: System Spects Problem: im unsure that CCC is using AMD card instead of Intel's, i have encountered several issues since updating to 8.1 and i don't know what to do What happened: Installed 8.1 patch first day After 1 minute of use, BBSOD, windows never loaded again System restore wouldnt recognize 8.0 restore points i did a system reset to windows 8 since the laptop was only 3 weeks old System Broke, it did restore to factory BUT kept the registry almost intact, i had to install almost everything again, since the factory drivers where working with the updated one's registry and several problems CCC Broke too <- What i've already done Installing new drivers on top of old ones didnt work, so i used AMD uninstaller first Uninstalled and Re-installed Intel's HD Graphics Driver Tried to install mobile center, but AMD told me that it wasnt compatible (even if thats the only driver that they provide via their page as seen Here) Tried to use Auto-Detect, couldnt install driver because card was disabled because it didnt have the drivers... (see what they did here?) Had to use a workaround with Samsung Update, the driver didnt appear as download so had to use search and downloaded the driver manually. Now the graphic card appears on device manager and catalyst but as 8800 series (not exact model), and cant check the card with neither dxdiag/GPU-z/HWMonitor when right-clicking on CCC only Intel card appears launching a game and using as "high performance" would speed it up a little but i cant be sure How to verify its working properly? HWMonitor wont show AMD card even when set to high performance Latest GPU-Z wont work because a problem with Intel's, and legacy ones wont either what can I do now? I don't even know if I fixed my problem or not, and i also want to to use Adobe Premier with it, and its locked (the option to run it with the amd card not intels) Edit: now it seems to work, but cant change the setting for adobe Premiere and other programs that i Need to

  Read the article

• How do I get Catalyst 11.10 with ATI Radeon Mobility HD 5470 working on an HP DV7?

  - by S Kumar

  I have a HP DV7 with a HD 5470 512M card. Installation of the Catalyst 11.10 is repeatedly failing on a fresh install of Ubuntu 11.10. Catalyst 11.8 proprietary drivers were working well with Ubuntu 11.04. I have tried installing directly from the .run and generating the distribution specific packages. Nothing has worked. After installation which goes through successfully, the system hangs on reboot after the flashing dots. I have to replace the /etc/X11/xorg.conf to get the X working. I have followed instructions as per the http://wiki.cchtml.com/index.php/Main_Page wiki. Request for support to ATI/AMD gives the response that this model is unsupported on Linux by HP :). Updated 14-Nov I have reverted back to the open source drivers which work well enough for me.

  Read the article

• How do I fix libdispatch problem crashing Mac OS X apps?

  - by david-ocallaghan

  In the last day I have started having a lot of brokenness on my Mac (MacBook Air running Mac OS X 10.6.2 with all software updates). Most noticably, iTunes no longer syncs with my iPhone. It fails with a crash dialog reporting "AppleMobileDeviceHelper quit unexpectedly" and an error dialog "iTunes was unable to load dataclass information from SyncServices. Reconnect or try again later." I've attempted the fix at support.apple.com/kb/HT1747 but it failed. I've also been having problems (at first seemingly unrelated) with the horrible Cisco VPN client, which started giving me this error: Error 51: Unable to communicate with the VPN subsystem I followed the steps at www.anders.com/cms/192/CiscoVPN/Error.51:.Unable.to.communicate.with.the.VPN.subsystem which don't seem to work for me, although I can connect if I use the command line with sudo : sudo vpnclient connect MyProfile I had a look in the Console app at the diagnostic messages and I noticed a pattern, that a number of apps were reporting "BUG IN CLIENT OF LIBDISPATCH". The affected programs are: AppleMobileBackup AppleMobileDeviceHelper Safari Webpage Preview Fetcher cvpnd (the Cisco VPN daemon) Of these, only the last is non-Apple software! The common text in the diagnostic messages is: Exception Type: EXC_BAD_INSTRUCTION (SIGILL) Exception Codes: 0x0000000000000001, 0x0000000000000000 Crashed Thread: 1 Dispatch queue: com.apple.libdispatch-manager Application Specific Information: BUG IN CLIENT OF LIBDISPATCH: Do not close random Unix descriptors I'm beginning to wonder if there's a permissions problem, or corruption of an important library, ... I should note that I've rebooted several times and verified the disk permissions and the disk. Any help would be great!

  Read the article

• Inter-VLAN Malicious Code Scanning

  - by Jackthedog

  I am trying to find an inbuilt solution on a Cisco Catayst 3750X Switch to scan all traffic routed from one VLAN to another for malicious code. The situation is that we currently have a development environment which is currently being redesigned to upgrade the network infrastructure to use the 3750X switches to manage server and workstation connectivity as well as inter-VLAN routing. We also have another system that is responsible for taking the builds created on the development environment and imaging various HDDs. Because these are two separate systems, we have a requirement in the workplace to anti-virus scan any data transferred between these systems. This is done by copying the data from the originating system to external USB HDD, scanning in a standalone workstation and then copying the data on to the receiving system. As you can imagine this is extremely tedious and impractical most of the time... (I don't make the rules). Anyway, with this redesign going on, we would like to join the imaging system to the network infrastructure of the development system, keeping separation by the use of VLANs and restricting traffic by using ACLs. As we still have the requirement to scan all traffic I would like to configure some sort of malicious code scanning when ever traffic is routed between these VLANs. I am aware I could install a separate in-line IPS/IDS device, however both systems will be using multiple ports on the switch (obviously), and we won't be able to put a device on each port. I would would prefer not to add additional hardware if the 3750x switch is capable of doing the job. Is anyone aware of any Cisco solution that I could use here, that ideally can be incorporated into the 3750x switch? Thanks in advance.

  Read the article

• Abnormally high amount of Transmit discards reported by Solarwinds for multiple switches

  - by Jared

  I have several 3750X Cisco switches that, according to our Solarwinds NPM, are producing billions of transmit discards per day. I'm not sure why it's reporting these discards. Many of the ports on the 3750X's have 2960's connected to them and are hardcoded as trunk ports. Solarwinds NPM version 10.3 Cisco IOS version 12.2(58)SE2 Total output drops: 29139431: GigabitEthernet1/0/43 is up, line protocol is up (connected) Hardware is Gigabit Ethernet, address is XXXX (bia XXXX) Description: XXXX MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100/1000BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:47, output 00:00:50, output hang never Last clearing of "show interface" counters 1w4d Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 29139431 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 35000 bits/sec, 56 packets/sec 51376 packets input, 9967594 bytes, 0 no buffer Received 51376 broadcasts (51376 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 51376 multicast, 0 pause input 0 input packets with dribble condition detected 115672302 packets output, 8673778028 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out sh controllers gigabitEthernet 1/0/43 utilization: Receive Bandwidth Percentage Utilization : 0 Transmit Bandwidth Percentage Utilization : 0

  Read the article

• Programmer configuring a new network

  - by David Lively

  I'm in the process of expanding my home network from a couple of laptops on a wireless Verizon FiOS router to include: Linksys 24-port switch Cisco Pix 515 Cisco 3640 router One new development desktop and three new machines to act as a db server, web server and a backup system. My company is moving offices and we've decommissioned some older hardware, which I was able to pick up for the cost of the labor to move it home from the office. The benefits to working with dedicated web and db servers are very valuable to me. I know very little about network topology, other than that everything plugs into the switch, which then plugs into the cheap Verizon router. (Verizon provides a coax connection that the router must translate into Ethernet before I can use it with any of this equipment). Questions: What is the recommended topology for this equipment? Verizon router - Pix - 3600 - switch? Is the 3600 even necessary or desirable? The Verizon router has one WAN port and 4 client ports, all 10/100. Is there any performance benefit at all to wiring multiple connections from the verizon router to the switch, assuming I don't use the Pix? Should I use the Pix? Software firewalls are a pain, and seem silly if I have a device like this lying around. Anything else I should know? Am I wasting my time with this? I also obtained a 7 foot rack, shelves, patch panels, UPS, patch panels, etc, which are going into a conveniently air conditioned closet. All constructive advice appreciated.

  Read the article

• Setting my NIC to full duplex

  - by David

  I am trying to optimize the network speed of my Solaris X86 server, and have discovered that the Cisco 3548 that it is connected to has issues with the NIC in my server. The NIC appears to have not been configured fully, and is coming up 100 half-duplex. The 3548 ports are all set to 100 full. Ideally I'd like to have the server set for 100 full, and have been attempting to configure it using ndd commands. However I have had no results. The following command: -bash-3.00# dladm show-dev rtls0 link: unknown speed: 100 Mbps duplex: unknown The NIC shows up as: pci bus 0x0001 cardnum 0x06 function 0x00: vendor 0x10ec device 0x8139 Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ which should be configurable. I have modified the configuration file from auto config (5) to 100 fdx (4) to no avail. If there is no other choice, I could alter the Cisco 3548 to be 100 half-duplex. However, this solution causes huge performance loss. Currently throughput is about 500Kbps, when it should be around 40Mbps.

  Read the article

• Regular Windows 7 BSOD with Shrew VPN client

  - by Junto

  The Shrew VPN client appears to be a good alternative to the Cisco VPN Client on x64 Windows 7. However, since installing it I've seen fairly regular BSODs. Minidump attached: Microsoft (R) Windows Debugger Version 6.11.0001.404 AMD64 Copyright (c) Microsoft Corporation. All rights reserved. Loading Dump File [D:\Temp\020810-23431-01.dmp] Mini Kernel Dump File: Only registers and stack trace are available Symbol search path is: SRV*d:\symbols*http://msdl.microsoft.com/download/symbols Executable search path is: Windows 7 Kernel Version 7600 MP (8 procs) Free x64 Product: WinNt, suite: TerminalServer SingleUserTS Built by: 7600.16385.amd64fre.win7_rtm.090713-1255 Machine Name: Kernel base = 0xfffff800`0285f000 PsLoadedModuleList = 0xfffff800`02a9ce50 Debug session time: Mon Feb 8 18:08:12.887 2010 (GMT+1) System Uptime: 0 days 7:52:06.120 Loading Kernel Symbols ............................................................... ................................................................ .............. Loading User Symbols Loading unloaded module list .... ******************************************************************************* * * * Bugcheck Analysis * * * ******************************************************************************* Use !analyze -v to get detailed debugging information. BugCheck A, {0, 2, 0, fffff800028d50b6} Unable to load image \SystemRoot\system32\DRIVERS\vfilter.sys, Win32 error 0n2 *** WARNING: Unable to verify timestamp for vfilter.sys *** ERROR: Module load completed but symbols could not be loaded for vfilter.sys Probably caused by : vfilter.sys ( vfilter+29a6 ) Followup: MachineOwner Machine is a brand spanking new Dell Precision T5500. Superuser appears to have several recommendations for the Shrew VPN Client as an alternative to the Cisco VPN client on 64 bit machines, so I wondered if anyone here has seen this problem and possibly found a solution to the problem? I've decided to run the VPN client under Windows 7 compatibility mode for the moment (Vista SP2) with administrator privileges to see if it makes a difference. Oddly, the VPN doesn't necessarily need to be connected. I've noticed it when browsing using Google Chrome and Internet Explorer, usually when I open up a new tab. If it carries on I think I'll be forced to shell out the 120 EUR for the NCP Client instead.

  Read the article

• ntop to analyse bandwidth usage on multiple ASA 5505

  - by dunxd

  I have set up a netflow server at our data centre, which is connected via VPN to ~40 remote offices using Cisco ASA 5505. The aim is to analyse usage data and find out exactly how the remote connections are being used. I followed through http://techowto.files.wordpress.com/2008/09/ntop-guide.pdf to set up ntop and https://supportforums.cisco.com/docs/DOC-6114 to set up the ASAs. I can see from the Plugin Netflow Statistics page that netflow packets from my ASAs are being received - the counter is increasing. However, I am not seeing any breakdown on the Global Traffic Statistic page after switching to the Netflow interface. I'm just seeing a pie chart showing 100% traffic for eth0. The interfaces and documentation are a little hard to follow so I am not sure I have got things configured correctly. When setting up my NetFlow-device.2 I can specify Virtual NetFlow Interface Network Address - the web UI says This value is in the form of a network address and mask on the network where the actual NetFlow probe is located. is this a Network address (e.g. 192.168.0.0/24) or an actual host IP address (192.167.0.1/24)? If that should be a network address, is this the network in which one of my ASAs is or the network in which my ntop server is? If a host IP address, is this the IP address used by eth0 on my ntop server, the IP address of an ASA, or something else? Do I need a separate virtual interface for each ASA I am collecting netflow data from? Any guidance would be greatly welcome.

  Read the article

< Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >