Search Results

Search found 559 results on 23 pages for 'decrease'.

Page 23/23 | < Previous Page | 19 20 21 22 23

TCP packets larger than 4 KB don't get a reply from Linux

- by pts

I'm running Linux 3.2.51 in a virtual machine (192.168.33.15). I'm sending Ethernet frames to it. I'm writing custom software trying to emulate a TCP peer, the other peer is Linux running in the virtual machine guest. I've noticed that TCP packets larger than about 4 KB are ignored (i.e. dropped without an ACK) by the Linux guest. If I decrease the packet size by 50 bytes, I get an ACK. I'm not sending new payload data until the Linux guest fully ACKs the previous one. I've increased ifconfig eth0 mtu 51000, and ping -c 1 -s 50000 goes through (from guest to my emulator) and the Linux guest gets a reply of the same size. I've also increased sysctl -w net.ipv4.tcp_rmem='70000 87380 87380 and tried with sysctl -w net.ipv4.tcp_mtu_probing=1 (and also =0). There is no IPv3 packet fragmentation, all packets have the DF flag set. It works the other way round: the Linux guest can send TCP packets of 6900 bytes of payload and my emulator understands them. This is very strange to me, because only TCP packets seem to be affected (large ICMP packets go through). Any idea what can be imposing this limit? Any idea how to do debug it in the Linux kernel? See the tcpdump -n -vv output below. tcpdump was run on the Linux guest. The last line is interesting: 4060 bytes of TCP payload is sent to the guest, and it doesn't get any reply packet from the Linux guest for half a minute. 14:59:32.000057 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 40) 192.168.33.1.36522 > 192.168.33.15.22: Flags [S], cksum 0x8da0 (correct), seq 10000000, win 14600, length 0 14:59:32.000086 IP (tos 0x10, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 44) 192.168.33.15.22 > 192.168.33.1.36522: Flags [S.], cksum 0xc37f (incorrect -> 0x5999), seq 1415680476, ack 10000001, win 19920, options [mss 9960], length 0 14:59:32.000218 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 40) 192.168.33.1.36522 > 192.168.33.15.22: Flags [.], cksum 0xa752 (correct), ack 1, win 14600, length 0 14:59:32.000948 IP (tos 0x10, ttl 64, id 53777, offset 0, flags [DF], proto TCP (6), length 66) 192.168.33.15.22 > 192.168.33.1.36522: Flags [P.], cksum 0xc395 (incorrect -> 0xfa01), seq 1:27, ack 1, win 19920, length 26 14:59:32.001575 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 40) 192.168.33.1.36522 > 192.168.33.15.22: Flags [.], cksum 0xa738 (correct), ack 27, win 14600, length 0 14:59:32.001585 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 65) 192.168.33.1.36522 > 192.168.33.15.22: Flags [P.], cksum 0x48d6 (correct), seq 1:26, ack 27, win 14600, length 25 14:59:32.001589 IP (tos 0x10, ttl 64, id 53778, offset 0, flags [DF], proto TCP (6), length 40) 192.168.33.15.22 > 192.168.33.1.36522: Flags [.], cksum 0xc37b (incorrect -> 0x9257), ack 26, win 19920, length 0 14:59:32.001680 IP (tos 0x10, ttl 64, id 53779, offset 0, flags [DF], proto TCP (6), length 496) 192.168.33.15.22 > 192.168.33.1.36522: Flags [P.], seq 27:483, ack 26, win 19920, length 456 14:59:32.001784 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 40) 192.168.33.1.36522 > 192.168.33.15.22: Flags [.], cksum 0xa557 (correct), ack 483, win 14600, length 0 14:59:32.006367 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 1136) 192.168.33.1.36522 > 192.168.33.15.22: Flags [P.], seq 26:1122, ack 483, win 14600, length 1096 14:59:32.044150 IP (tos 0x10, ttl 64, id 53780, offset 0, flags [DF], proto TCP (6), length 40) 192.168.33.15.22 > 192.168.33.1.36522: Flags [.], cksum 0xc37b (incorrect -> 0x8c47), ack 1122, win 19920, length 0 14:59:32.045310 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 312) 192.168.33.1.36522 > 192.168.33.15.22: Flags [P.], seq 1122:1394, ack 483, win 14600, length 272 14:59:32.045322 IP (tos 0x10, ttl 64, id 53781, offset 0, flags [DF], proto TCP (6), length 40) 192.168.33.15.22 > 192.168.33.1.36522: Flags [.], cksum 0xc37b (incorrect -> 0x8b37), ack 1394, win 19920, length 0 14:59:32.925726 IP (tos 0x10, ttl 64, id 53782, offset 0, flags [DF], proto TCP (6), length 1112) 192.168.33.15.22 > 192.168.33.1.36522: Flags [.], seq 483:1555, ack 1394, win 19920, length 1072 14:59:32.925750 IP (tos 0x10, ttl 64, id 53784, offset 0, flags [DF], proto TCP (6), length 312) 192.168.33.15.22 > 192.168.33.1.36522: Flags [P.], seq 1555:1827, ack 1394, win 19920, length 272 14:59:32.927131 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 40) 192.168.33.1.36522 > 192.168.33.15.22: Flags [.], cksum 0x9bcf (correct), ack 1555, win 14600, length 0 14:59:32.927148 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 40) 192.168.33.1.36522 > 192.168.33.15.22: Flags [.], cksum 0x9abf (correct), ack 1827, win 14600, length 0 14:59:32.932248 IP (tos 0x10, ttl 64, id 53785, offset 0, flags [DF], proto TCP (6), length 56) 192.168.33.15.22 > 192.168.33.1.36522: Flags [P.], cksum 0xc38b (incorrect -> 0xd247), seq 1827:1843, ack 1394, win 19920, length 16 14:59:32.932366 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 40) 192.168.33.1.36522 > 192.168.33.15.22: Flags [.], cksum 0x9aaf (correct), ack 1843, win 14600, length 0 14:59:32.964295 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 104) 192.168.33.1.36522 > 192.168.33.15.22: Flags [P.], seq 1394:1458, ack 1843, win 14600, length 64 14:59:32.964310 IP (tos 0x10, ttl 64, id 53786, offset 0, flags [DF], proto TCP (6), length 40) 192.168.33.15.22 > 192.168.33.1.36522: Flags [.], cksum 0xc37b (incorrect -> 0x85a7), ack 1458, win 19920, length 0 14:59:32.964561 IP (tos 0x10, ttl 64, id 53787, offset 0, flags [DF], proto TCP (6), length 88) 192.168.33.15.22 > 192.168.33.1.36522: Flags [P.], seq 1843:1891, ack 1458, win 19920, length 48 14:59:32.965185 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 40) 192.168.33.1.36522 > 192.168.33.15.22: Flags [.], cksum 0x9a3f (correct), ack 1891, win 14600, length 0 14:59:32.965196 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 104) 192.168.33.1.36522 > 192.168.33.15.22: Flags [P.], seq 1458:1522, ack 1891, win 14600, length 64 14:59:32.965233 IP (tos 0x10, ttl 64, id 53788, offset 0, flags [DF], proto TCP (6), length 88) 192.168.33.15.22 > 192.168.33.1.36522: Flags [P.], seq 1891:1939, ack 1522, win 19920, length 48 14:59:32.965970 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 40) 192.168.33.1.36522 > 192.168.33.15.22: Flags [.], cksum 0x99cf (correct), ack 1939, win 14600, length 0 14:59:32.965979 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 568) 192.168.33.1.36522 > 192.168.33.15.22: Flags [P.], seq 1522:2050, ack 1939, win 14600, length 528 14:59:32.966112 IP (tos 0x10, ttl 64, id 53789, offset 0, flags [DF], proto TCP (6), length 520) 192.168.33.15.22 > 192.168.33.1.36522: Flags [P.], seq 1939:2419, ack 2050, win 19920, length 480 14:59:32.970059 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 40) 192.168.33.1.36522 > 192.168.33.15.22: Flags [.], cksum 0x95df (correct), ack 2419, win 14600, length 0 14:59:32.970089 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 616) 192.168.33.1.36522 > 192.168.33.15.22: Flags [P.], seq 2050:2626, ack 2419, win 14600, length 576 14:59:32.981159 IP (tos 0x10, ttl 64, id 53790, offset 0, flags [DF], proto TCP (6), length 72) 192.168.33.15.22 > 192.168.33.1.36522: Flags [P.], cksum 0xc39b (incorrect -> 0xa84f), seq 2419:2451, ack 2626, win 19920, length 32 14:59:32.982347 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 40) 192.168.33.1.36522 > 192.168.33.15.22: Flags [.], cksum 0x937f (correct), ack 2451, win 14600, length 0 14:59:32.982357 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 104) 192.168.33.1.36522 > 192.168.33.15.22: Flags [P.], seq 2626:2690, ack 2451, win 14600, length 64 14:59:32.982401 IP (tos 0x10, ttl 64, id 53791, offset 0, flags [DF], proto TCP (6), length 88) 192.168.33.15.22 > 192.168.33.1.36522: Flags [P.], seq 2451:2499, ack 2690, win 19920, length 48 14:59:32.982570 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 40) 192.168.33.1.36522 > 192.168.33.15.22: Flags [.], cksum 0x930f (correct), ack 2499, win 14600, length 0 14:59:32.982702 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 104) 192.168.33.1.36522 > 192.168.33.15.22: Flags [P.], seq 2690:2754, ack 2499, win 14600, length 64 14:59:33.020066 IP (tos 0x10, ttl 64, id 53792, offset 0, flags [DF], proto TCP (6), length 40) 192.168.33.15.22 > 192.168.33.1.36522: Flags [.], cksum 0xc37b (incorrect -> 0x7e07), ack 2754, win 19920, length 0 14:59:33.983503 IP (tos 0x10, ttl 64, id 53793, offset 0, flags [DF], proto TCP (6), length 72) 192.168.33.15.22 > 192.168.33.1.36522: Flags [P.], cksum 0xc39b (incorrect -> 0x2aa7), seq 2499:2531, ack 2754, win 19920, length 32 14:59:33.983810 IP (tos 0x10, ttl 64, id 53794, offset 0, flags [DF], proto TCP (6), length 88) 192.168.33.15.22 > 192.168.33.1.36522: Flags [P.], seq 2531:2579, ack 2754, win 19920, length 48 14:59:33.984100 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 40) 192.168.33.1.36522 > 192.168.33.15.22: Flags [.], cksum 0x92af (correct), ack 2531, win 14600, length 0 14:59:33.984139 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 40) 192.168.33.1.36522 > 192.168.33.15.22: Flags [.], cksum 0x927f (correct), ack 2579, win 14600, length 0 14:59:34.022914 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 104) 192.168.33.1.36522 > 192.168.33.15.22: Flags [P.], seq 2754:2818, ack 2579, win 14600, length 64 14:59:34.022939 IP (tos 0x10, ttl 64, id 53795, offset 0, flags [DF], proto TCP (6), length 40) 192.168.33.15.22 > 192.168.33.1.36522: Flags [.], cksum 0xc37b (incorrect -> 0x7d77), ack 2818, win 19920, length 0 14:59:34.023554 IP (tos 0x10, ttl 64, id 53796, offset 0, flags [DF], proto TCP (6), length 88) 192.168.33.15.22 > 192.168.33.1.36522: Flags [P.], seq 2579:2627, ack 2818, win 19920, length 48 14:59:34.027571 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 40) 192.168.33.1.36522 > 192.168.33.15.22: Flags [.], cksum 0x920f (correct), ack 2627, win 14600, length 0 14:59:34.027603 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto TCP (6), length 4100) 192.168.33.1.36522 > 192.168.33.15.22: Flags [P.], seq 2818:6878, ack 2627, win 14600, length 4060

Read the article
I need advices: small memory footprint linux mail server with spam filtering

- by petermolnar

I have a VPS which is originally destined to be a webserver but some minimal mail capabilities are needed to be deployed as well, including sending and receiving as standalone server. The current setup is the following: Postfix reveices the mail, the users are in virtual tables, stored in MySQL on connection all servers are tested with policyd-weight service against some DNSBLs all mail is runs through SpamAssassin spamd with the help of spamc client the mail is then delivered with Dovecot 2' LDA (local delivery agent), virtual users as well As you saw... there's no virus scanner running, and that's for a reason: clamav eats all the memory possible and also, virus mails are all filtered out with this setup (I've tested the same with ClamAV enabled for 1,5 years, no virus mail ever got even to ClamAV) I don't use amavisd and I really don't want to. You only need that monster if you have plenty of memory and lots of simultaneous scanners. It's also a nightmare to fine tune by hand. I run policyd-weight instead of policyd and native DNSBLs in postfix. I don't like to send someone away because a single service listed them. Important statement: everything works fine. I receive very small amount of spam, nearly never get a false positive and most of the bad mail is stopped by policyd-weight. The only "problem" that I feel the services at total uses a bit much memory alltogether. I've already cut the modules of spamassassin (see below), but I'd really like to hear some advices how to cut the memory footprint as low as possible, mostly: what plugins SpamAssassin really needs and what are more or less useless, regarding to my current postfix & policyd-weight setup? SpamAssassin rules are also compiled with sa-compile (sa-update runs once a week from cron, compile runs right after that) These are some of the current configurations that may matter, please tell me if you need anything more. postfix/master.cf (parts only) dovecot unix - n n - - pipe flags=DRhu user=vmail:vmail argv=/usr/bin/spamc -e /usr/lib/dovecot/deliver -d ${recipient} -f {sender} postfix/main.cf (parts only) smtpd_helo_required = yes smtpd_helo_restrictions = permit_mynetworks, reject_invalid_hostname, permit smtpd_recipient_restrictions = permit_mynetworks, permit_sasl_authenticated, reject_invalid_hostname, reject_non_fqdn_hostname, reject_non_fqdn_recipient, reject_unknown_recipient_domain, reject_unauth_pipelining, reject_unauth_destination, check_policy_service inet:127.0.0.1:12525, permit policyd-weight.conf (parts only) $REJECTMSG = "550 Mail appeared to be SPAM or forged. Ask your Mail/DNS-Administrator to correct HELO and DNS MX settings or to get removed from DNSBLs"; $REJECTLEVEL = 4; $DEFER_STRING = 'IN_SPAMCOP= BOGUS_MX='; $DEFER_ACTION = '450'; $DEFER_LEVEL = 5; $DNSERRMSG = '450 No DNS entries for your MTA, HELO and Domain. Contact YOUR administrator'; # 1: ON, 0: OFF (default) # If ON request that ALL clients are only checked against RBLs $dnsbl_checks_only = 0; # 1: ON (default), 0: OFF # When set to ON it logs only RBLs which affect scoring (positive or negative) $LOG_BAD_RBL_ONLY = 1; ## DNSBL settings @dnsbl_score = ( # host, hit, miss, log name 'dnsbl.ahbl.org', 3, -1, 'dnsbl.ahbl.org', 'dnsbl.njabl.org', 3, -1, 'dnsbl.njabl.org', 'dnsbl.sorbs.net', 3, -1, 'dnsbl.sorbs.net', 'bl.spamcop.net', 3, -1, 'bl.spamcop.net', 'zen.spamhaus.org', 3, -1, 'zen.spamhaus.org', 'pbl.spamhaus.org', 3, -1, 'pbl.spamhaus.org', 'cbl.abuseat.org', 3, -1, 'cbl.abuseat.org', 'list.dsbl.org', 3, -1, 'list.dsbl.org', ); # If Client IP is listed in MORE DNSBLS than this var, it gets REJECTed immediately $MAXDNSBLHITS = 3; # alternatively, if the score of DNSBLs is ABOVE this level, reject immediately $MAXDNSBLSCORE = 9; $MAXDNSBLMSG = '550 Az levelezoszerveruk IP cime tul sok spamlistan talahato, kerjuk ellenorizze! / Your MTA is listed in too many DNSBLs; please check.'; ## RHSBL settings @rhsbl_score = ( 'multi.surbl.org', 4, 0, 'multi.surbl.org', 'rhsbl.ahbl.org', 4, 0, 'rhsbl.ahbl.org', 'dsn.rfc-ignorant.org', 4, 0, 'dsn.rfc-ignorant.org', # 'postmaster.rfc-ignorant.org', 0.1, 0, 'postmaster.rfc-ignorant.org', # 'abuse.rfc-ignorant.org', 0.1, 0, 'abuse.rfc-ignorant.org' ); # skip a RBL if this RBL had this many continuous errors $BL_ERROR_SKIP = 2; # skip a RBL for that many times $BL_SKIP_RELEASE = 10; ## cache stuff # must be a directory (add trailing slash) $LOCKPATH = '/var/run/policyd-weight/'; # socket path for the cache daemon. $SPATH = $LOCKPATH.'/polw.sock'; # how many seconds the cache may be idle before starting maintenance routines #NOTE: standard maintenance jobs happen regardless of this setting. $MAXIDLECACHE = 60; # after this number of requests do following maintenance jobs: checking for config changes $MAINTENANCE_LEVEL = 5; # negative (i.e. SPAM) result cache settings ################################## # set to 0 to disable caching for spam results. To this level the cache will be cleaned. $CACHESIZE = 2000; # at this number of entries cleanup takes place $CACHEMAXSIZE = 4000; $CACHEREJECTMSG = '550 temporarily blocked because of previous errors'; # after NTTL retries the cache entry is deleted $NTTL = 1; # client MUST NOT retry within this seconds in order to decrease TTL counter $NTIME = 30; # positve (i.,e. HAM) result cache settings ################################### # set to 0 to disable caching of HAM. To this number of entries the cache will be cleaned $POSCACHESIZE = 1000; # at this number of entries cleanup takes place $POSCACHEMAXSIZE = 2000; $POSCACHEMSG = 'using cached result'; #after PTTL requests the HAM entry must succeed one time the RBL checks again $PTTL = 60; # after $PTIME in HAM Cache the client must pass one time the RBL checks again. #Values must be nonfractal. Accepted time-units: s, m, h, d $PTIME = '3h'; # The client must pass this time the RBL checks in order to be listed as hard-HAM # After this time the client will pass immediately for PTTL within PTIME $TEMP_PTIME = '1d'; ## DNS settings # Retries for ONE DNS-Lookup $DNS_RETRIES = 1; # Retry-interval for ONE DNS-Lookup $DNS_RETRY_IVAL = 5; # max error count for unresponded queries in a complete policy query $MAXDNSERR = 3; $MAXDNSERRMSG = 'passed - too many local DNS-errors'; # persistent udp connection for DNS queries. #broken in Net::DNS version 0.51. Works with Net::DNS 0.53; DEFAULT: off $PUDP= 0; # Force the usage of Net::DNS for RBL lookups. # Normally policyd-weight tries to use a faster RBL lookup routine instead of Net::DNS $USE_NET_DNS = 0; # A list of space separated NS IPs # This overrides resolv.conf settings # Example: $NS = '1.2.3.4 1.2.3.5'; # DEFAULT: empty $NS = ''; # timeout for receiving from cache instance $IPC_TIMEOUT = 2; # If set to 1 policyd-weight closes connections to smtpd clients in order to avoid too many #established connections to one policyd-weight child $TRY_BALANCE = 0; # scores for checks, WARNING: they may manipulate eachother # or be factors for other scores. # HIT score, MISS Score @client_ip_eq_helo_score = (1.5, -1.25 ); @helo_score = (1.5, -2 ); @helo_score = (0, -2 ); @helo_from_mx_eq_ip_score= (1.5, -3.1 ); @helo_numeric_score= (2.5, 0 ); @from_match_regex_verified_helo= (1,-2 ); @from_match_regex_unverified_helo = (1.6, -1.5 ); @from_match_regex_failed_helo = (2.5, 0 ); @helo_seems_dialup = (1.5, 0 ); @failed_helo_seems_dialup= (2, 0 ); @helo_ip_in_client_subnet= (0,-1.2 ); @helo_ip_in_cl16_subnet = (0,-0.41 ); #@client_seems_dialup_score = (3.75, 0 ); @client_seems_dialup_score = (0, 0 ); @from_multiparted = (1.09, 0 ); @from_anon= (1.17, 0 ); @bogus_mx_score = (2.1, 0 ); @random_sender_score = (0.25, 0 ); @rhsbl_penalty_score = (3.1, 0 ); @enforce_dyndns_score = (3, 0 ); spamassassin/init.pre (I've put the .pre files together) loadplugin Mail::SpamAssassin::Plugin::Hashcash loadplugin Mail::SpamAssassin::Plugin::SPF loadplugin Mail::SpamAssassin::Plugin::Pyzor loadplugin Mail::SpamAssassin::Plugin::Razor2 loadplugin Mail::SpamAssassin::Plugin::AutoLearnThreshold loadplugin Mail::SpamAssassin::Plugin::MIMEHeader loadplugin Mail::SpamAssassin::Plugin::ReplaceTags loadplugin Mail::SpamAssassin::Plugin::Check loadplugin Mail::SpamAssassin::Plugin::HTTPSMismatch loadplugin Mail::SpamAssassin::Plugin::URIDetail loadplugin Mail::SpamAssassin::Plugin::Bayes loadplugin Mail::SpamAssassin::Plugin::BodyEval loadplugin Mail::SpamAssassin::Plugin::DNSEval loadplugin Mail::SpamAssassin::Plugin::HTMLEval loadplugin Mail::SpamAssassin::Plugin::HeaderEval loadplugin Mail::SpamAssassin::Plugin::MIMEEval loadplugin Mail::SpamAssassin::Plugin::RelayEval loadplugin Mail::SpamAssassin::Plugin::URIEval loadplugin Mail::SpamAssassin::Plugin::WLBLEval loadplugin Mail::SpamAssassin::Plugin::VBounce loadplugin Mail::SpamAssassin::Plugin::Rule2XSBody spamassassin/local.cf (parts) use_bayes 1 bayes_auto_learn 1 bayes_store_module Mail::SpamAssassin::BayesStore::MySQL bayes_sql_dsn DBI:mysql:db:127.0.0.1:3306 bayes_sql_username user bayes_sql_password pass bayes_ignore_header X-Bogosity bayes_ignore_header X-Spam-Flag bayes_ignore_header X-Spam-Status ### User settings user_scores_dsn DBI:mysql:db:127.0.0.1:3306 user_scores_sql_password user user_scores_sql_username pass user_scores_sql_custom_query SELECT preference, value FROM _TABLE_ WHERE username = _USERNAME_ OR username = '$GLOBAL' OR username = CONCAT('%',_DOMAIN_) ORDER BY username ASC # for better speed score DNS_FROM_AHBL_RHSBL 0 score __RFC_IGNORANT_ENVFROM 0 score DNS_FROM_RFC_DSN 0 score DNS_FROM_RFC_BOGUSMX 0 score __DNS_FROM_RFC_POST 0 score __DNS_FROM_RFC_ABUSE 0 score __DNS_FROM_RFC_WHOIS 0 UPDATE 01 As adaptr advised I remove policyd-weight and configured postfix postscreen, this resulted approximately -15-20 MB from RAM usage and a lot faster work. I'm not sure it's working at full capacity but it seems promising.

Read the article
Picker view wont rotate- iPhone

- by lotuseater

hi, I am making a booking page. I have included 3 pickers in it. I have included all the delegates required for the pickers to work but it wont rotate. I have enabled user interaction and multitouch in the nib file. Here is my code. Please help me. :( @interface ChooseContactsFrom : UIViewController { IBOutlet UIPickerView *statePickup; IBOutlet UIPickerView *paymentMethodPickup; IBOutlet UIDatePicker *expiryDatePickup; IBOutlet UIView *statePickupView; IBOutlet UIView *paymentMethodPickupView; IBOutlet UIView *expiryDatePickupView; } (void)viewDidLoad { self.title = @"Choose Contacts"; //Fill in the states name/ stateArray = [[NSArray alloc]initWithObjects:@"",nil]; paymentModeArray = [[NSArray alloc] initWithObjects:@"Credit Card", @"Cash",@"Account",@"Voucher",@"Debit Card", nil]; paymentMethodPickup.frame = CGRectMake(0.0, 44.0, paymentMethodPickup.frame.size.width, paymentMethodPickup.frame.size.height); paymentMethodPickup.userInteractionEnabled = YES; paymentMethodPickup.multipleTouchEnabled = YES; paymentMethodPickupView.frame = CGRectMake(0.0, 210.0, paymentMethodPickupView.frame.size.width, paymentMethodPickupView.frame.size.height); statePickup.frame = CGRectMake(0.0, 44.0,statePickup.frame.size.width, statePickup.frame.size.height); statePickupView.frame = CGRectMake(0.0, 210.0, statePickupView.frame.size.width, statePickupView.frame.size.height); stateArray = [[NSArray alloc] initWithObjects:@"state1", @"state2", @"state3", @"state4", @"state5", @"state6", @"state7", @"state8", @"state9", @"state10", nil]; expiryDatePickup.frame = CGRectMake(0.0, 44.0, expiryDatePickup.frame.size.width, expiryDatePickup.frame.size.height); expiryDatePickupView.frame = CGRectMake(0.0, 210.0, expiryDatePickupView.frame.size.width, expiryDatePickupView.frame.size.height); [super viewDidLoad]; } -(IBAction)back:(id)sender { [self dismissModalViewControllerAnimated:YES]; } pragma mark pickerView delegates (NSInteger)numberOfComponentsInPickerView:(UIPickerView *)thePickerView { return 1; } (NSInteger)pickerView:(UIPickerView *)thePickerView numberOfRowsInComponent:(NSInteger)component { if( thePickerView == statePickup) { return [stateArray count]; } else if(thePickerView == paymentMethodPickup) { return [paymentModeArray count]; } else { return 0; } } (NSString *)pickerView:(UIPickerView *)thePickerView titleForRow:(NSInteger)row forComponent:(NSInteger)component { if(thePickerView == statePickup) { return [stateArray objectAtIndex:row]; } else if(thePickerView == paymentMethodPickup) { return [paymentModeArray objectAtIndex:row]; } else { return @" "; } } (CGFloat)pickerView:(UIPickerView *)pickerView rowHeightForComponent:(NSInteger)component{ return 50; } (CGFloat)pickerView:(UIPickerView *)pickerView widthForComponent:(NSInteger)component { return 250; } (void)pickerView:(UIPickerView *)thepickerView didSelectRow:(NSInteger)row inComponent:(NSInteger)component { if(thepickerView == statePickup) { state.text=[stateArray objectAtIndex:row]; } if(thepickerView == paymentMethodPickup) { payment.text=[paymentModeArray objectAtIndex:row]; } } (void)ClearSubviews { //[firstName resignFirstResponder]; // [lastName resignFirstResponder]; // [email resignFirstResponder]; // [address1 resignFirstResponder]; // [address2 resignFirstResponder]; // [city resignFirstResponder]; // //[state resignFirstResponder]; // [payment resignFirstResponder]; // [creditCard resignFirstResponder]; // [expirydate removeFromSuperview]; // [statePickup removeFromSuperview]; // [paymentMethodPickup removeFromSuperview]; } (BOOL)textFieldShouldBeginEditing:(UITextField *)textField { // [self showPicker:textField]; //[self setViewMovedUp]; if(textField == firstName || textField == lastName || textField == email || textField == address1 || textField == address2 ||textField == city) { [self ClearSubviews]; //pickerToolbar.hidden = TRUE; return YES; } else if(textField == payment) { [self ClearSubviews]; [self setViewMovedUp]; [payment setText:[paymentModeArray objectAtIndex:0]]; [self.view insertSubview:paymentMethodPickupView aboveSubview:self.view]; return NO; } else if(textField == state) { [self ClearSubviews]; [self setViewMovedUp]; [state setText:[stateArray objectAtIndex:0]]; [self.view insertSubview:statePickupView aboveSubview:self.view]; return NO; } else if(textField == expirydate) { [self setViewMovedUp]; expiryDatePickup.date = [NSDate date]; NSDate *date1 = [NSDate date]; NSDateFormatter *dateFormatter = [[NSDateFormatter alloc] init]; [dateFormatter setDateStyle:NSDateFormatterMediumStyle]; NSString *strDate=[dateFormatter stringFromDate:date1]; NSString *str=[[NSString alloc] initWithString: strDate]; [expirydate setText:str]; [self.view insertSubview:expiryDatePickupView aboveSubview:self.view]; return NO; } else if(textField == creditCard) { [self ClearSubviews]; [self setViewMovedUp]; return YES; } else { [self ClearSubviews]; return YES; } } -(BOOL)textFieldShouldEndEditing:(UITextField *)textField { return YES; } (void)textFieldDidEndEditing:(UITextField *)textField { if(textField == creditCard) { [self moveDown]; } } (BOOL)textFieldShouldReturn:(UITextField *)textField { [firstName resignFirstResponder]; [lastName resignFirstResponder]; [email resignFirstResponder]; [address1 resignFirstResponder]; [address2 resignFirstResponder]; [city resignFirstResponder]; [creditCard resignFirstResponder]; return YES; } -(IBAction)textFieldDoneEditing:(id)sender { [sender resignFirstResponder]; } ////////----------------------------------------------------------------------- pragma mark move screen (void)setViewMovedUp { [UIView beginAnimations:nil context:NULL]; [UIView setAnimationDuration:0.3]; // Make changes to the view's frame inside the animation block. They will be animated instead // of taking place immediately. CGRect rect = [self.view frame]; // If moving up, not only decrease the origin but increase the height so the view // covers the entire screen behind the keyboard. rect.origin.y -= 50.0f; rect.size.height -= 80.0f; [self.view setFrame:rect]; [UIView commitAnimations]; } -(void)moveDown { [UIView beginAnimations:nil context:NULL]; [UIView setAnimationDuration:0.3]; // Make changes to the view's frame inside the animation block. They will be animated instead // of taking place immediately. CGRect rect = [self.view frame]; rect.origin.y += 50.0f; rect.size.height += 80.0f; [self.view setFrame:rect]; // [UIView setBackgroundColor:[UIColor darkGrayColor]]; [UIView commitAnimations]; } pragma mark Method to show pickers -(void)showPicker:(UITextField *)textField { if(textField == expirydate) { expiryDatePickup .date = [NSDate date]; NSDate *date1 = [NSDate date]; NSDateFormatter *dateFormatter = [[NSDateFormatter alloc] init]; [dateFormatter setDateStyle:NSDateFormatterMediumStyle]; NSString *strDate=[dateFormatter stringFromDate:date1]; NSString *str=[[NSString alloc] initWithString: strDate]; [expirydate setText:str]; [self.view insertSubview:expiryDatePickup aboveSubview:self.view]; } else if(textField == payment) { [payment setText:[paymentModeArray objectAtIndex:0]]; [self.view insertSubview:paymentMethodPickupView aboveSubview:self.view]; } else if(textField == state) { [state setText:[stateArray objectAtIndex:0]]; [self.view insertSubview:statePickupView aboveSubview:self.view]; } } (IBAction)datePickerChanged:(id)sender { NSDateFormatter *dateFormatter = [[NSDateFormatter alloc] init]; [dateFormatter setDateStyle:NSDateFormatterMediumStyle]; NSDate *date=expiryDatePickup.date; formattedDateString1 = [dateFormatter stringFromDate:date]; [expirydate setText:formattedDateString1]; NSCalendar *gregorian = [[NSCalendar alloc] initWithCalendarIdentifier:NSGregorianCalendar]; unsigned int unitFlags = NSMonthCalendarUnit | NSDayCalendarUnit; components = [gregorian components:unitFlags fromDate:date]; [gregorian release]; } pragma mark done and cancel methods -(IBAction) btnCancelExpiryDate:(id)sender { [self moveDown]; [expirydate setText:@" "]; [expiryDatePickupView removeFromSuperview]; } -(IBAction) btnDoneExpiryDate:(id)sender { [self moveDown]; [expiryDatePickupView removeFromSuperview]; expiryDatePickup .date = [NSDate date]; } -(IBAction)cancelPaymentType:(id)sender { [self moveDown]; [payment setText:@" "]; [paymentMethodPickupView removeFromSuperview]; } -(IBAction)donePaymentType:(id)sender { [self moveDown]; [paymentMethodPickupView removeFromSuperview]; } -(IBAction)doneState:(id)sender { [self moveDown]; [statePickupView removeFromSuperview]; } (IBAction)cancelState:(id)sender; { [self moveDown]; [state setText:@" "]; [statePickupView removeFromSuperview]; }

Read the article
Solving embarassingly parallel problems using Python multiprocessing

- by gotgenes

How does one use multiprocessing to tackle embarrassingly parallel problems? Embarassingly parallel problems typically consist of three basic parts: Read input data (from a file, database, tcp connection, etc.). Run calculations on the input data, where each calculation is independent of any other calculation. Write results of calculations (to a file, database, tcp connection, etc.). We can parallelize the program in two dimensions: Part 2 can run on multiple cores, since each calculation is independent; order of processing doesn't matter. Each part can run independently. Part 1 can place data on an input queue, part 2 can pull data off the input queue and put results onto an output queue, and part 3 can pull results off the output queue and write them out. This seems a most basic pattern in concurrent programming, but I am still lost in trying to solve it, so let's write a canonical example to illustrate how this is done using multiprocessing. Here is the example problem: Given a CSV file with rows of integers as input, compute their sums. Separate the problem into three parts, which can all run in parallel: Process the input file into raw data (lists/iterables of integers) Calculate the sums of the data, in parallel Output the sums Below is traditional, single-process bound Python program which solves these three tasks: #!/usr/bin/env python # -*- coding: UTF-8 -*- # basicsums.py """A program that reads integer values from a CSV file and writes out their sums to another CSV file. """ import csv import optparse import sys def make_cli_parser(): """Make the command line interface parser.""" usage = "\n\n".join(["python %prog INPUT_CSV OUTPUT_CSV", __doc__, """ ARGUMENTS: INPUT_CSV: an input CSV file with rows of numbers OUTPUT_CSV: an output file that will contain the sums\ """]) cli_parser = optparse.OptionParser(usage) return cli_parser def parse_input_csv(csvfile): """Parses the input CSV and yields tuples with the index of the row as the first element, and the integers of the row as the second element. The index is zero-index based. :Parameters: - `csvfile`: a `csv.reader` instance """ for i, row in enumerate(csvfile): row = [int(entry) for entry in row] yield i, row def sum_rows(rows): """Yields a tuple with the index of each input list of integers as the first element, and the sum of the list of integers as the second element. The index is zero-index based. :Parameters: - `rows`: an iterable of tuples, with the index of the original row as the first element, and a list of integers as the second element """ for i, row in rows: yield i, sum(row) def write_results(csvfile, results): """Writes a series of results to an outfile, where the first column is the index of the original row of data, and the second column is the result of the calculation. The index is zero-index based. :Parameters: - `csvfile`: a `csv.writer` instance to which to write results - `results`: an iterable of tuples, with the index (zero-based) of the original row as the first element, and the calculated result from that row as the second element """ for result_row in results: csvfile.writerow(result_row) def main(argv): cli_parser = make_cli_parser() opts, args = cli_parser.parse_args(argv) if len(args) != 2: cli_parser.error("Please provide an input file and output file.") infile = open(args[0]) in_csvfile = csv.reader(infile) outfile = open(args[1], 'w') out_csvfile = csv.writer(outfile) # gets an iterable of rows that's not yet evaluated input_rows = parse_input_csv(in_csvfile) # sends the rows iterable to sum_rows() for results iterable, but # still not evaluated result_rows = sum_rows(input_rows) # finally evaluation takes place as a chain in write_results() write_results(out_csvfile, result_rows) infile.close() outfile.close() if __name__ == '__main__': main(sys.argv[1:]) Let's take this program and rewrite it to use multiprocessing to parallelize the three parts outlined above. Below is a skeleton of this new, parallelized program, that needs to be fleshed out to address the parts in the comments: #!/usr/bin/env python # -*- coding: UTF-8 -*- # multiproc_sums.py """A program that reads integer values from a CSV file and writes out their sums to another CSV file, using multiple processes if desired. """ import csv import multiprocessing import optparse import sys NUM_PROCS = multiprocessing.cpu_count() def make_cli_parser(): """Make the command line interface parser.""" usage = "\n\n".join(["python %prog INPUT_CSV OUTPUT_CSV", __doc__, """ ARGUMENTS: INPUT_CSV: an input CSV file with rows of numbers OUTPUT_CSV: an output file that will contain the sums\ """]) cli_parser = optparse.OptionParser(usage) cli_parser.add_option('-n', '--numprocs', type='int', default=NUM_PROCS, help="Number of processes to launch [DEFAULT: %default]") return cli_parser def main(argv): cli_parser = make_cli_parser() opts, args = cli_parser.parse_args(argv) if len(args) != 2: cli_parser.error("Please provide an input file and output file.") infile = open(args[0]) in_csvfile = csv.reader(infile) outfile = open(args[1], 'w') out_csvfile = csv.writer(outfile) # Parse the input file and add the parsed data to a queue for # processing, possibly chunking to decrease communication between # processes. # Process the parsed data as soon as any (chunks) appear on the # queue, using as many processes as allotted by the user # (opts.numprocs); place results on a queue for output. # # Terminate processes when the parser stops putting data in the # input queue. # Write the results to disk as soon as they appear on the output # queue. # Ensure all child processes have terminated. # Clean up files. infile.close() outfile.close() if __name__ == '__main__': main(sys.argv[1:]) These pieces of code, as well as another piece of code that can generate example CSV files for testing purposes, can be found on github. I would appreciate any insight here as to how you concurrency gurus would approach this problem. Here are some questions I had when thinking about this problem. Bonus points for addressing any/all: Should I have child processes for reading in the data and placing it into the queue, or can the main process do this without blocking until all input is read? Likewise, should I have a child process for writing the results out from the processed queue, or can the main process do this without having to wait for all the results? Should I use a processes pool for the sum operations? If yes, what method do I call on the pool to get it to start processing the results coming into the input queue, without blocking the input and output processes, too? apply_async()? map_async()? imap()? imap_unordered()? Suppose we didn't need to siphon off the input and output queues as data entered them, but could wait until all input was parsed and all results were calculated (e.g., because we know all the input and output will fit in system memory). Should we change the algorithm in any way (e.g., not run any processes concurrently with I/O)?

Read the article
Different behavior of functors (copies, assignments) in VS2010 (compared with VS2005)

- by Patrick

When moving from VS2005 to VS2010 we noticed a performance decrease, which seemed to be caused by additional copies of a functor. The following code illustrates the problem. It is essential to have a map where the value itself is a set. On both the map and the set we defined a comparison functor (which is templated in the example). #include <iostream> #include <map> #include <set> class A { public: A(int i, char c) : m_i(i), m_c(c) { std::cout << "Construct object " << m_c << m_i << std::endl; } A(const A &a) : m_i(a.m_i), m_c(a.m_c) { std::cout << "Copy object " << m_c << m_i << std::endl; } ~A() { std::cout << "Destruct object " << m_c << m_i << std::endl; } void operator= (const A &a) { m_i = a.m_i; m_c = a.m_c; std::cout << "Assign object " << m_c << m_i << std::endl; } int m_i; char m_c; }; class B : public A { public: B(int i) : A(i, 'B') { } static const char s_c = 'B'; }; class C : public A { public: C(int i) : A(i, 'C') { } static const char s_c = 'C'; }; template <class X> class compareA { public: compareA() : m_i(999) { std::cout << "Construct functor " << X::s_c << m_i << std::endl; } compareA(const compareA &a) : m_i(a.m_i) { std::cout << "Copy functor " << X::s_c << m_i << std::endl; } ~compareA() { std::cout << "Destruct functor " << X::s_c << m_i << std::endl; } void operator= (const compareA &a) { m_i = a.m_i; std::cout << "Assign functor " << X::s_c << m_i << std::endl; } bool operator() (const X &x1, const X &x2) const { std::cout << "Comparing object " << x1.m_i << " with " << x2.m_i << std::endl; return x1.m_i < x2.m_i; } private: int m_i; }; typedef std::set<C, compareA<C> > SetTest; typedef std::map<B, SetTest, compareA<B> > MapTest; int main() { int i = 0; std::cout << "--- " << i++ << std::endl; MapTest mapTest; std::cout << "--- " << i++ << std::endl; SetTest &setTest = mapTest[0]; std::cout << "--- " << i++ << std::endl; } If I compile this code with VS2005 I get the following output: --- 0 Construct functor B999 Copy functor B999 Copy functor B999 Destruct functor B999 Destruct functor B999 --- 1 Construct object B0 Construct functor C999 Copy functor C999 Copy functor C999 Destruct functor C999 Destruct functor C999 Copy object B0 Copy functor C999 Copy functor C999 Copy functor C999 Destruct functor C999 Destruct functor C999 Copy object B0 Copy functor C999 Copy functor C999 Copy functor C999 Destruct functor C999 Destruct functor C999 Destruct functor C999 Destruct object B0 Destruct functor C999 Destruct object B0 --- 2 If I compile this with VS2010, I get the following output: --- 0 Construct functor B999 Copy functor B999 Copy functor B999 Destruct functor B999 Destruct functor B999 --- 1 Construct object B0 Construct functor C999 Copy functor C999 Copy functor C999 Destruct functor C999 Destruct functor C999 Copy object B0 Copy functor C999 Copy functor C999 Copy functor C999 Destruct functor C999 Destruct functor C999 Copy functor C999 Assign functor C999 Assign functor C999 Destruct functor C999 Copy object B0 Copy functor C999 Copy functor C999 Copy functor C999 Destruct functor C999 Destruct functor C999 Copy functor C999 Assign functor C999 Assign functor C999 Destruct functor C999 Destruct functor C999 Destruct object B0 Destruct functor C999 Destruct object B0 --- 2 The output for the first statement (constructing the map) is identical. The output for the second statement (creating the first element in the map and getting a reference to it), is much bigger in the VS2010 case: Copy constructor of functor: 10 times vs 8 times Assignment of functor: 2 times vs. 0 times Destructor of functor: 10 times vs 8 times My questions are: Why does the STL copy a functor? Isn't it enough to construct it once for every instantiation of the set? Why is the functor constructed more in the VS2010 case than in the VS2005 case? (didn't check VS2008) And why is it assigned two times in VS2010 and not in VS2005? Are there any tricks to avoid the copy of functors? I saw a similar question at http://stackoverflow.com/questions/2216041/prevent-unnecessary-copies-of-c-functor-objects but I'm not sure that's the same question. Thanks in advance, Patrick

Read the article
FreeBSD performance tuning. Sysctls, loader.conf, kernel

- by SaveTheRbtz

I wanted to share knowledge of tuning FreeBSD via sysctl.conf/loader.conf/KENCONF. It was initially based on Igor Sysoev's (author of nginx) presentation about FreeBSD tuning up to 100,000-200,000 active connections. Tunings are for FreeBSD-CURRENT. Since 7.2 amd64 some of them are tuned well by default. Prior 7.0 some of them are boot only (set via /boot/loader.conf) or does not exist at all. sysctl.conf: # No zero mapping feature # May break wine # (There are also reports about broken samba3) #security.bsd.map_at_zero=0 # If you have really busy webserver with apache13 you may run out of processes #kern.maxproc=10000 # Same for servers with apache2 / Pound #kern.threads.max_threads_per_proc=4096 # Max. backlog size kern.ipc.somaxconn=4096 # Shared memory // 7.2+ can use shared memory > 2Gb kern.ipc.shmmax=2147483648 # Sockets kern.ipc.maxsockets=204800 # Can cause this on older kernels: # http://old.nabble.com/Significant-performance-regression-for-increased-maxsockbuf-on-8.0-RELEASE-tt26745981.html#a26745981 ) kern.ipc.maxsockbuf=10485760 # Mbuf 2k clusters (on amd64 7.2+ 25600 is default) # For such high value vm.kmem_size must be increased to 3G kern.ipc.nmbclusters=262144 # Jumbo pagesize(_SC_PAGESIZE) clusters # Used as general packet storage for jumbo frames # can be monitored via `netstat -m` #kern.ipc.nmbjumbop=262144 # Jumbo 9k/16k clusters # If you are using them #kern.ipc.nmbjumbo9=65536 #kern.ipc.nmbjumbo16=32768 # For lower latency you can decrease scheduler's maximum time slice # default: stathz/10 (~ 13) #kern.sched.slice=1 # Increase max command-line length showed in `ps` (e.g for Tomcat/Java) # Default is PAGE_SIZE / 16 or 256 on x86 # This avoids commands to be presented as [executable] in `ps` # For more info see: http://www.freebsd.org/cgi/query-pr.cgi?pr=120749 kern.ps_arg_cache_limit=4096 # Every socket is a file, so increase them kern.maxfiles=204800 kern.maxfilesperproc=200000 kern.maxvnodes=200000 # On some systems HPET is almost 2 times faster than default ACPI-fast # Useful on systems with lots of clock_gettime / gettimeofday calls # See http://old.nabble.com/ACPI-fast-default-timecounter,-but-HPET-83--faster-td23248172.html # After revision 222222 HPET became default: http://svnweb.freebsd.org/base?view=revision&revision=222222 kern.timecounter.hardware=HPET # Small receive space, only usable on http-server, on file server this # should be increased to 65535 or even more #net.inet.tcp.recvspace=8192 # This is useful on Fat-Long-Pipes #net.inet.tcp.recvbuf_max=10485760 #net.inet.tcp.recvbuf_inc=65535 # Small send space is useful for http servers that serve small files # Autotuned since 7.x net.inet.tcp.sendspace=16384 # This is useful on Fat-Long-Pipes #net.inet.tcp.sendbuf_max=10485760 #net.inet.tcp.sendbuf_inc=65535 # Turn off receive autotuning # You can play with it. #net.inet.tcp.recvbuf_auto=0 #net.inet.tcp.sendbuf_auto=0 # This should be enabled if you going to use big spaces (>64k) # Also timestamp field is useful when using syncookies net.inet.tcp.rfc1323=1 # Turn this off on high-speed, lossless connections (LAN 1Gbit+) # If you set it there is no need in TCP_NODELAY sockopt (see man tcp) net.inet.tcp.delayed_ack=0 # This feature is useful if you are serving data over modems, Gigabit Ethernet, # or even high speed WAN links (or any other link with a high bandwidth delay product), # especially if you are also using window scaling or have configured a large send window. # Automatically disables on small RTT ( http://www.freebsd.org/cgi/cvsweb.cgi/src/sys/netinet/tcp_subr.c?#rev1.237 ) # This sysctl was removed in 10-CURRENT: # See: http://www.mail-archive.com/[email protected]/msg06178.html #net.inet.tcp.inflight.enable=0 # TCP slowstart algorithm tunings # We assuming we have very fast clients #net.inet.tcp.slowstart_flightsize=100 #net.inet.tcp.local_slowstart_flightsize=100 # Disable randomizing of ports to avoid false RST # Before usage check SA here www.bsdcan.org/2006/papers/ImprovingTCPIP.pdf # (it's also says that port randomization auto-disables at some conn.rates, but I didn't checked it thou) #net.inet.ip.portrange.randomized=0 # Increase portrange # For outgoing connections only. Good for seed-boxes and ftp servers. net.inet.ip.portrange.first=1024 net.inet.ip.portrange.last=65535 # # stops route cache degregation during a high-bandwidth flood # http://www.freebsd.org/doc/en/books/handbook/securing-freebsd.html #net.inet.ip.rtexpire=2 net.inet.ip.rtminexpire=2 net.inet.ip.rtmaxcache=1024 # Security net.inet.ip.redirect=0 net.inet.ip.sourceroute=0 net.inet.ip.accept_sourceroute=0 net.inet.icmp.maskrepl=0 net.inet.icmp.log_redirect=0 net.inet.icmp.drop_redirect=1 net.inet.tcp.drop_synfin=1 # # There is also good example of sysctl.conf with comments: # http://www.thern.org/projects/sysctl.conf # # icmp may NOT rst, helpful for those pesky spoofed # icmp/udp floods that end up taking up your outgoing # bandwidth/ifqueue due to all that outgoing RST traffic. # #net.inet.tcp.icmp_may_rst=0 # Security net.inet.udp.blackhole=1 net.inet.tcp.blackhole=2 # IPv6 Security # For more info see http://www.fosslc.org/drupal/content/security-implications-ipv6 # Disable Node info replies # To see this vulnerability in action run `ping6 -a sglAac ::1` or `ping6 -w ::1` on unprotected node net.inet6.icmp6.nodeinfo=0 # Turn on IPv6 privacy extensions # For more info see proposal http://unix.derkeiler.com/Mailing-Lists/FreeBSD/net/2008-06/msg00103.html net.inet6.ip6.use_tempaddr=1 net.inet6.ip6.prefer_tempaddr=1 # Disable ICMP redirect net.inet6.icmp6.rediraccept=0 # Disable acceptation of RA and auto linklocal generation if you don't use them #net.inet6.ip6.accept_rtadv=0 #net.inet6.ip6.auto_linklocal=0 # Increases default TTL, sometimes useful # Default is 64 net.inet.ip.ttl=128 # Lessen max segment life to conserve resources # ACK waiting time in miliseconds # (default: 30000. RFC from 1979 recommends 120000) net.inet.tcp.msl=5000 # Max bumber of timewait sockets net.inet.tcp.maxtcptw=200000 # Don't use tw on local connections # As of 15 Apr 2009. Igor Sysoev says that nolocaltimewait has some buggy realization. # So disable it or now till get fixed #net.inet.tcp.nolocaltimewait=1 # FIN_WAIT_2 state fast recycle net.inet.tcp.fast_finwait2_recycle=1 # Time before tcp keepalive probe is sent # default is 2 hours (7200000) #net.inet.tcp.keepidle=60000 # Should be increased until net.inet.ip.intr_queue_drops is zero net.inet.ip.intr_queue_maxlen=4096 # Interrupt handling via multiple CPU, but with context switch. # You can play with it. Default is 1; #net.isr.direct=0 # This is for routers only #net.inet.ip.forwarding=1 #net.inet.ip.fastforwarding=1 # This speed ups dummynet when channel isn't saturated net.inet.ip.dummynet.io_fast=1 # Increase dummynet(4) hash #net.inet.ip.dummynet.hash_size=2048 #net.inet.ip.dummynet.max_chain_len # Should be increased when you have A LOT of files on server # (Increase until vfs.ufs.dirhash_mem becomes lower) vfs.ufs.dirhash_maxmem=67108864 # Note from commit http://svn.freebsd.org/base/head@211031 : # For systems with RAID volumes and/or virtualization envirnments, where # read performance is very important, increasing this sysctl tunable to 32 # or even more will demonstratively yield additional performance benefits. vfs.read_max=32 # Explicit Congestion Notification (see http://en.wikipedia.org/wiki/Explicit_Congestion_Notification) net.inet.tcp.ecn.enable=1 # Flowtable - flow caching mechanism # Useful for routers #net.inet.flowtable.enable=1 #net.inet.flowtable.nmbflows=65535 # Extreme polling tuning #kern.polling.burst_max=1000 #kern.polling.each_burst=1000 #kern.polling.reg_frac=100 #kern.polling.user_frac=1 #kern.polling.idle_poll=0 # IPFW dynamic rules and timeouts tuning # Increase dyn_buckets till net.inet.ip.fw.curr_dyn_buckets is lower net.inet.ip.fw.dyn_buckets=65536 net.inet.ip.fw.dyn_max=65536 net.inet.ip.fw.dyn_ack_lifetime=120 net.inet.ip.fw.dyn_syn_lifetime=10 net.inet.ip.fw.dyn_fin_lifetime=2 net.inet.ip.fw.dyn_short_lifetime=10 # Make packets pass firewall only once when using dummynet # i.e. packets going thru pipe are passing out from firewall with accept #net.inet.ip.fw.one_pass=1 # shm_use_phys Wires all shared pages, making them unswappable # Use this to lessen Virtual Memory Manager's work when using Shared Mem. # Useful for databases #kern.ipc.shm_use_phys=1 # ZFS # Enable prefetch. Useful for sequential load type i.e fileserver. # FreeBSD sets vfs.zfs.prefetch_disable to 1 on any i386 systems and # on any amd64 systems with less than 4GB of avaiable memory # For additional info check this nabble thread http://old.nabble.com/Samba-read-speed-performance-tuning-td27964534.html #vfs.zfs.prefetch_disable=0 # On highload servers you may notice following message in dmesg: # "Approaching the limit on PV entries, consider increasing either the # vm.pmap.shpgperproc or the vm.pmap.pv_entry_max tunable" vm.pmap.shpgperproc=2048 loader.conf: # Accept filters for data, http and DNS requests # Useful when your software uses select() instead of kevent/kqueue or when you under DDoS # DNS accf available on 8.0+ accf_data_load="YES" accf_http_load="YES" accf_dns_load="YES" # Async IO system calls aio_load="YES" # Linux specific devices in /dev # As for 8.1 it only /dev/full #lindev_load="YES" # Adds NCQ support in FreeBSD # WARNING! all ad[0-9]+ devices will be renamed to ada[0-9]+ # 8.0+ only #ahci_load="YES" #siis_load="YES" # FreeBSD 8.2+ # New Congestion Control for FreeBSD # http://caia.swin.edu.au/urp/newtcp/tools/cc_chd-readme-0.1.txt # http://www.ietf.org/proceedings/78/slides/iccrg-5.pdf # Initial merge commit message http://www.mail-archive.com/[email protected]/msg31410.html #cc_chd_load="YES" # Increase kernel memory size to 3G. # # Use ONLY if you have KVA_PAGES in kernel configuration, and you have more than 3G RAM # Otherwise panic will happen on next reboot! # # It's required for high buffer sizes: kern.ipc.nmbjumbop, kern.ipc.nmbclusters, etc # Useful on highload stateful firewalls, proxies or ZFS fileservers # (FreeBSD 7.2+ amd64 users: Check that current value is lower!) #vm.kmem_size="3G" # If your server has lots of swap (>4Gb) you should increase following value # according to http://lists.freebsd.org/pipermail/freebsd-hackers/2009-October/029616.html # Otherwise you'll be getting errors # "kernel: swap zone exhausted, increase kern.maxswzone" # kern.maxswzone="256M" # Older versions of FreeBSD can't tune maxfiles on the fly #kern.maxfiles="200000" # Useful for databases # Sets maximum data size to 1G # (FreeBSD 7.2+ amd64 users: Check that current value is lower!) #kern.maxdsiz="1G" # Maximum buffer size(vfs.maxbufspace) # You can check current one via vfs.bufspace # Should be lowered/upped depending on server's load-type # Usually decreased to preserve kmem # (default is 10% of mem) #kern.maxbcache="512M" # Sendfile buffers # For i386 only #kern.ipc.nsfbufs=10240 # FreeBSD 9+ # HPET "legacy route" support. It should allow HPET to work per-CPU # See http://www.mail-archive.com/[email protected]/msg03603.html #hint.atrtc.0.clock=0 #hint.attimer.0.clock=0 #hint.hpet.0.legacy_route=1 # syncache Hash table tuning net.inet.tcp.syncache.hashsize=1024 net.inet.tcp.syncache.bucketlimit=512 net.inet.tcp.syncache.cachelimit=65536 # Increased hostcache # Later host cache can be viewed via net.inet.tcp.hostcache.list hidden sysctl # Very useful for it's RTT RTTVAR # Must be power of two net.inet.tcp.hostcache.hashsize=65536 # hashsize * bucketlimit (which is 30 by default) # It allocates 255Mb (1966080*136) of RAM net.inet.tcp.hostcache.cachelimit=1966080 # TCP control-block Hash table tuning net.inet.tcp.tcbhashsize=4096 # Disable ipfw deny all # Should be uncommented when there is a chance that # kernel and ipfw binary may be out-of sync on next reboot #net.inet.ip.fw.default_to_accept=1 # # SIFTR (Statistical Information For TCP Research) is a kernel module that # logs a range of statistics on active TCP connections to a log file. # See prerelease notes http://groups.google.com/group/mailing.freebsd.current/browse_thread/thread/b4c18be6cdce76e4 # and man 4 sitfr #siftr_load="YES" # Enable superpages, for 7.2+ only # Also read http://lists.freebsd.org/pipermail/freebsd-hackers/2009-November/030094.html vm.pmap.pg_ps_enabled=1 # Usefull if you are using Intel-Gigabit NIC #hw.em.rxd=4096 #hw.em.txd=4096 #hw.em.rx_process_limit="-1" # Also if you have ALOT interrupts on NIC - play with following parameters # NOTE: You should set them for every NIC #dev.em.0.rx_int_delay: 250 #dev.em.0.tx_int_delay: 250 #dev.em.0.rx_abs_int_delay: 250 #dev.em.0.tx_abs_int_delay: 250 # There is also multithreaded version of em/igb drivers can be found here: # http://people.yandex-team.ru/~wawa/ # # for additional em monitoring and statistics use # sysctl dev.em.0.stats=1 ; dmesg # sysctl dev.em.0.debug=1 ; dmesg # Also after r209242 (-CURRENT) there is a separate sysctl for each stat variable; # Same tunings for igb #hw.igb.rxd=4096 #hw.igb.txd=4096 #hw.igb.rx_process_limit=100 # Some useful netisr tunables. See sysctl net.isr #net.isr.maxthreads=4 #net.isr.defaultqlimit=4096 #net.isr.maxqlimit: 10240 # Bind netisr threads to CPUs #net.isr.bindthreads=1 # # FreeBSD 9.x+ # Increase interface send queue length # See commit message http://svn.freebsd.org/viewvc/base?view=revision&revision=207554 #net.link.ifqmaxlen=1024 # Nicer boot logo =) loader_logo="beastie" And finally here is KERNCONF: # Just some of them, see also # cat /sys/{i386,amd64,}/conf/NOTES # This one useful only on i386 #options KVA_PAGES=512 # You can play with HZ in environments with high interrupt rate (default is 1000) # 100 is for my notebook to prolong it's battery life #options HZ=100 # Polling is goot on network loads with high packet rates and low-end NICs # NB! Do not enable it if you want more than one netisr thread #options DEVICE_POLLING # Eliminate datacopy on socket read-write # To take advantage with zero copy sockets you should have an MTU >= 4k # This req. is only for receiving data. # Read more in man zero_copy_sockets # Also this epic thread on kernel trap: # http://kerneltrap.org/node/6506 # Here Linus says that "anybody that does it that way (FreeBSD) is totally incompetent" #options ZERO_COPY_SOCKETS # Support TCP sign. Used for IPSec options TCP_SIGNATURE # There was stackoverflow found in KAME IPSec stack: # See http://secunia.com/advisories/43995/ # For quick workaround you can use `ipfw add deny proto ipcomp` options IPSEC # This ones can be loaded as modules. They described in loader.conf section #options ACCEPT_FILTER_DATA #options ACCEPT_FILTER_HTTP # Adding ipfw, also can be loaded as modules options IPFIREWALL # On 8.1+ you can disable verbose to see blocked packets on ipfw0 interface. # Also there is no point in compiling verbose into the kernel, because # now there is net.inet.ip.fw.verbose tunable. #options IPFIREWALL_VERBOSE #options IPFIREWALL_VERBOSE_LIMIT=10 options IPFIREWALL_FORWARD # Adding kernel NAT options IPFIREWALL_NAT options LIBALIAS # Traffic shaping options DUMMYNET # Divert, i.e. for userspace NAT options IPDIVERT # This is for OpenBSD's pf firewall device pf device pflog # pf's QoS - ALTQ options ALTQ options ALTQ_CBQ # Class Bases Queuing (CBQ) options ALTQ_RED # Random Early Detection (RED) options ALTQ_RIO # RED In/Out options ALTQ_HFSC # Hierarchical Packet Scheduler (HFSC) options ALTQ_PRIQ # Priority Queuing (PRIQ) options ALTQ_NOPCC # Required for SMP build # Pretty console # Manual can be found here http://forums.freebsd.org/showthread.php?t=6134 #options VESA #options SC_PIXEL_MODE # Disable reboot on Ctrl Alt Del #options SC_DISABLE_REBOOT # Change normal|kernel messages color options SC_NORM_ATTR=(FG_GREEN|BG_BLACK) options SC_KERNEL_CONS_ATTR=(FG_YELLOW|BG_BLACK) # More scroll space options SC_HISTORY_SIZE=8192 # Adding hardware crypto device device crypto device cryptodev # Useful network interfaces device vlan device tap #Virtual Ethernet driver device gre #IP over IP tunneling device if_bridge #Bridge interface device pfsync #synchronization interface for PF device carp #Common Address Redundancy Protocol device enc #IPsec interface device lagg #Link aggregation interface device stf #IPv4-IPv6 port # Also for my notebook, but may be used with Opteron device amdtemp # Same for Intel processors device coretemp # man 4 cpuctl device cpuctl # CPU control pseudo-device # Support for ECMP. More than one route for destination # Works even with default route so one can use it as LB for two ISP # For now code is unstable and panics (panic: rtfree 2) on route deletions. #options RADIX_MPATH # Multicast routing #options MROUTING #options PIM # Debug & DTrace options KDB # Kernel debugger related code options KDB_TRACE # Print a stack trace for a panic options KDTRACE_FRAME # amd64-only(?) options KDTRACE_HOOKS # all architectures - enable general DTrace hooks #options DDB #options DDB_CTF # all architectures - kernel ELF linker loads CTF data # Adaptive spining in lockmgr (8.x+) # See http://www.mail-archive.com/[email protected]/msg10782.html options ADAPTIVE_LOCKMGRS # UTF-8 in console (8.x+) #options TEKEN_UTF8 # FreeBSD 8.1+ # Deadlock resolver thread # For additional information see http://www.mail-archive.com/[email protected]/msg18124.html # (FYI: "resolution" is panic so use with caution) #options DEADLKRES # Increase maximum size of Raw I/O and sendfile(2) readahead #options MAXPHYS=(1024*1024) #options MAXBSIZE=(1024*1024) # For scheduler debug enable following option. # Debug will be available via `kern.sched.stats` sysctl # For more information see http://svnweb.freebsd.org/base/head/sys/conf/NOTES?view=markup #options SCHED_STATS If you are tuning network for maximum performance you may wish to play with ifconfig options like: # You can list all capabilities via `ifconfig -m` ifconfig [-]rxcsum [-]txcsum [-]tso [-]lro mtu In case you've enabled DDB in kernel config, you should edit your /etc/ddb.conf and add something like this to enable automatic reboot (and textdump as bonus): script kdb.enter.panic=textdump set; capture on; show pcpu; bt; ps; alltrace; capture off; call doadump; reset script kdb.enter.default=textdump set; capture on; bt; ps; capture off; call doadump; reset And do not forget to add ddb_enable="YES" to /etc/rc.conf Since FreeBSD 9 you can select to enable/disable flowcontrol on your NIC: # See http://en.wikipedia.org/wiki/Ethernet_flow_control and # http://www.mail-archive.com/[email protected]/msg07927.html for additional info ifconfig bge0 media auto mediaopt flowcontrol PS. Also most of FreeBSD's limits can be monitored by # vmstat -z and # limits PPS. variety of network counters can be monitored via # netstat -s In FreeBSD-9 netstat's -Q option appeared, try following command to display netisr stats # netstat -Q PPPS. also see # man 7 tuning PPPPS. I wanted to thank FreeBSD community, especially author of nginx - Igor Sysoev, nginx-ru@ and FreeBSD-performance@ mailing lists for providing useful information about FreeBSD tuning. FreeBSD WIP * Whats cooking for FreeBSD 7? * Whats cooking for FreeBSD 8? * Whats cooking for FreeBSD 9? So here is the question: What tunings are you using on yours FreeBSD servers? You can also post your /etc/sysctl.conf, /boot/loader.conf, kernel options, etc with description of its' meaning (do not copy-paste from sysctl -d). Don't forget to specify server type (web, smb, gateway, etc) Let's share experience!

Read the article
video and file caching with squid lusca?

- by moon

hello all i have configured squid lusca on ubuntu 11.04 version and also configured the video caching but the problem is the squid cannot configure the video more than 2 min long and the file of size upto 5.xx mbs only. here is my config please guide me how can i cache the long videos and files with squid: > # PORT and Transparent Option http_port 8080 transparent server_http11 on icp_port 0 > > # Cache Directory , modify it according to your system. > # but first create directory in root by mkdir /cache1 > # and then issue this command chown proxy:proxy /cache1 > # [for ubuntu user is proxy, in Fedora user is SQUID] > # I have set 500 MB for caching reserved just for caching , > # adjust it according to your need. > # My recommendation is to have one cache_dir per drive. zzz > > #store_dir_select_algorithm round-robin cache_dir aufs /cache1 500 16 256 cache_replacement_policy heap LFUDA memory_replacement_policy heap > LFUDA > > # If you want to enable DATE time n SQUID Logs,use following emulate_httpd_log on logformat squid %tl %6tr %>a %Ss/%03Hs %<st %rm > %ru %un %Sh/%<A %mt log_fqdn off > > # How much days to keep users access web logs > # You need to rotate your log files with a cron job. For example: > # 0 0 * * * /usr/local/squid/bin/squid -k rotate logfile_rotate 14 debug_options ALL,1 cache_access_log /var/log/squid/access.log > cache_log /var/log/squid/cache.log cache_store_log > /var/log/squid/store.log > > #I used DNSAMSQ service for fast dns resolving > #so install by using "apt-get install dnsmasq" first dns_nameservers 127.0.0.1 101.11.11.5 ftp_user anonymous@ ftp_list_width 32 ftp_passive on ftp_sanitycheck on > > #ACL Section acl all src 0.0.0.0/0.0.0.0 acl manager proto cache_object acl localhost src 127.0.0.1/255.255.255.255 acl > to_localhost dst 127.0.0.0/8 acl SSL_ports port 443 563 # https, snews > acl SSL_ports port 873 # rsync acl Safe_ports port 80 # http acl > Safe_ports port 21 # ftp acl Safe_ports port 443 563 # https, snews > acl Safe_ports port 70 # gopher acl Safe_ports port 210 # wais acl > Safe_ports port 1025-65535 # unregistered ports acl Safe_ports port > 280 # http-mgmt acl Safe_ports port 488 # gss-http acl Safe_ports port > 591 # filemaker acl Safe_ports port 777 # multiling http acl > Safe_ports port 631 # cups acl Safe_ports port 873 # rsync acl > Safe_ports port 901 # SWAT acl purge method PURGE acl CONNECT method > CONNECT http_access allow manager localhost http_access deny manager > http_access allow purge localhost http_access deny purge http_access > deny !Safe_ports http_access deny CONNECT !SSL_ports http_access allow > localhost http_access allow all http_reply_access allow all icp_access > allow all > > #========================== > # Administrative Parameters > #========================== > > # I used UBUNTU so user is proxy, in FEDORA you may use use squid cache_effective_user proxy cache_effective_group proxy cache_mgr > [email protected] visible_hostname proxy.aacable.net unique_hostname > [email protected] > > #============= > # ACCELERATOR > #============= half_closed_clients off quick_abort_min 0 KB quick_abort_max 0 KB vary_ignore_expire on reload_into_ims on log_fqdn > off memory_pools off > > # If you want to hide your proxy machine from being detected at various site use following via off > > #============================================ > # OPTIONS WHICH AFFECT THE CACHE SIZE / zaib > #============================================ > # If you have 4GB memory in Squid box, we will use formula of 1/3 > # You can adjust it according to your need. IF squid is taking too much of RAM > # Then decrease it to 128 MB or even less. > > cache_mem 256 MB minimum_object_size 512 bytes maximum_object_size 500 > MB maximum_object_size_in_memory 128 KB > > #============================================================$ > # SNMP , if you want to generate graphs for SQUID via MRTG > #============================================================$ > #acl snmppublic snmp_community gl > #snmp_port 3401 > #snmp_access allow snmppublic all > #snmp_access allow all > > #============================================================ > # ZPH , To enable cache content to be delivered at full lan speed, > # To bypass the queue at MT. > #============================================================ tcp_outgoing_tos 0x30 all zph_mode tos zph_local 0x30 zph_parent 0 > zph_option 136 > > # Caching Youtube acl videocache_allow_url url_regex -i \.youtube\.com\/get_video\? acl videocache_allow_url url_regex -i > \.youtube\.com\/videoplayback \.youtube\.com\/videoplay > \.youtube\.com\/get_video\? acl videocache_allow_url url_regex -i > \.youtube\.[a-z][a-z]\/videoplayback \.youtube\.[a-z][a-z]\/videoplay > \.youtube\.[a-z][a-z]\/get_video\? acl videocache_allow_url url_regex > -i \.googlevideo\.com\/videoplayback \.googlevideo\.com\/videoplay \.googlevideo\.com\/get_video\? acl videocache_allow_url url_regex -i > \.google\.com\/videoplayback \.google\.com\/videoplay > \.google\.com\/get_video\? acl videocache_allow_url url_regex -i > \.google\.[a-z][a-z]\/videoplayback \.google\.[a-z][a-z]\/videoplay > \.google\.[a-z][a-z]\/get_video\? acl videocache_allow_url url_regex > -i proxy[a-z0-9\-][a-z0-9][a-z0-9][a-z0-9]?\.dailymotion\.com\/ acl videocache_allow_url url_regex -i vid\.akm\.dailymotion\.com\/ acl > videocache_allow_url url_regex -i > [a-z0-9][0-9a-z][0-9a-z]?[0-9a-z]?[0-9a-z]?\.xtube\.com\/(.*)flv acl > videocache_allow_url url_regex -i \.vimeo\.com\/(.*)\.(flv|mp4) acl > videocache_allow_url url_regex -i > va\.wrzuta\.pl\/wa[0-9][0-9][0-9][0-9]? acl videocache_allow_url > url_regex -i \.youporn\.com\/(.*)\.flv acl videocache_allow_url > url_regex -i \.msn\.com\.edgesuite\.net\/(.*)\.flv acl > videocache_allow_url url_regex -i \.tube8\.com\/(.*)\.(flv|3gp) acl > videocache_allow_url url_regex -i \.mais\.uol\.com\.br\/(.*)\.flv acl > videocache_allow_url url_regex -i > \.blip\.tv\/(.*)\.(flv|avi|mov|mp3|m4v|mp4|wmv|rm|ram|m4v) acl > videocache_allow_url url_regex -i > \.apniisp\.com\/(.*)\.(flv|avi|mov|mp3|m4v|mp4|wmv|rm|ram|m4v) acl > videocache_allow_url url_regex -i \.break\.com\/(.*)\.(flv|mp4) acl > videocache_allow_url url_regex -i redtube\.com\/(.*)\.flv acl > videocache_allow_dom dstdomain .mccont.com .metacafe.com > .cdn.dailymotion.com acl videocache_deny_dom dstdomain > .download.youporn.com .static.blip.tv acl dontrewrite url_regex > redbot\.org \.php acl getmethod method GET > > storeurl_access deny dontrewrite storeurl_access deny !getmethod > storeurl_access deny videocache_deny_dom storeurl_access allow > videocache_allow_url storeurl_access allow videocache_allow_dom > storeurl_access deny all > > storeurl_rewrite_program /etc/squid/storeurl.pl > storeurl_rewrite_children 7 storeurl_rewrite_concurrency 10 > > acl store_rewrite_list urlpath_regex -i > \/(get_video\?|videodownload\?|videoplayback.*id) acl > store_rewrite_list urlpath_regex -i \.flv$ \.mp3$ \.mp4$ \.swf$ \ > storeurl_access allow store_rewrite_list storeurl_access deny all > > refresh_pattern -i \.flv$ 10080 80% 10080 override-expire > override-lastmod reload-into-ims ignore-reload ignore-no-cache > ignore-private ignore-auth refresh_pattern -i \.mp3$ 10080 80% 10080 > override-expire override-lastmod reload-into-ims ignore-reload > ignore-no-cache ignore-private ignore-auth refresh_pattern -i \.mp4$ > 10080 80% 10080 override-expire override-lastmod reload-into-ims > ignore-reload ignore-no-cache ignore-private ignore-auth > refresh_pattern -i \.swf$ 10080 80% 10080 override-expire > override-lastmod reload-into-ims ignore-reload ignore-no-cache > ignore-private ignore-auth refresh_pattern -i \.gif$ 10080 80% 10080 > override-expire override-lastmod reload-into-ims ignore-reload > ignore-no-cache ignore-private ignore-auth refresh_pattern -i \.jpg$ > 10080 80% 10080 override-expire override-lastmod reload-into-ims > ignore-reload ignore-no-cache ignore-private ignore-auth > refresh_pattern -i \.jpeg$ 10080 80% 10080 override-expire > override-lastmod reload-into-ims ignore-reload ignore-no-cache > ignore-private ignore-auth refresh_pattern -i \.exe$ 10080 80% 10080 > override-expire override-lastmod reload-into-ims ignore-reload > ignore-no-cache ignore-private ignore-auth > > # 1 year = 525600 mins, 1 month = 10080 mins, 1 day = 1440 refresh_pattern (get_video\?|videoplayback\?|videodownload\?|\.flv?) > 10080 80% 10080 ignore-no-cache ignore-private override-expire > override-lastmod reload-into-ims refresh_pattern > (get_video\?|videoplayback\?id|videoplayback.*id|videodownload\?|\.flv?) > 10080 80% 10080 ignore-no-cache ignore-private override-expire > override-lastmod reload-into-ims refresh_pattern \.(ico|video-stats) > 10080 80% 10080 override-expire ignore-reload ignore-no-cache > ignore-private ignore-auth override-lastmod negative-ttl=10080 > refresh_pattern \.etology\? 10080 > 80% 10080 override-expire ignore-reload ignore-no-cache > refresh_pattern galleries\.video(\?|sz) 10080 > 80% 10080 override-expire ignore-reload ignore-no-cache > refresh_pattern brazzers\? 10080 > 80% 10080 override-expire ignore-reload ignore-no-cache > refresh_pattern \.adtology\? 10080 > 80% 10080 override-expire ignore-reload ignore-no-cache > refresh_pattern > ^.*(utm\.gif|ads\?|rmxads\.com|ad\.z5x\.net|bh\.contextweb\.com|bstats\.adbrite\.com|a1\.interclick\.com|ad\.trafficmp\.com|ads\.cubics\.com|ad\.xtendmedia\.com|\.googlesyndication\.com|advertising\.com|yieldmanager|game-advertising\.com|pixel\.quantserve\.com|adperium\.com|doubleclick\.net|adserving\.cpxinteractive\.com|syndication\.com|media.fastclick.net).* > 10080 20% 10080 ignore-no-cache ignore-private override-expire > ignore-reload ignore-auth negative-ttl=40320 max-stale=10 > refresh_pattern ^.*safebrowsing.*google 10080 80% 10080 > override-expire ignore-reload ignore-no-cache ignore-private > ignore-auth negative-ttl=10080 refresh_pattern > ^http://((cbk|mt|khm|mlt)[0-9]?)\.google\.co(m|\.uk) 10080 80% > 10080 override-expire ignore-reload ignore-private negative-ttl=10080 > refresh_pattern ytimg\.com.*\.jpg > 10080 80% 10080 override-expire ignore-reload refresh_pattern > images\.friendster\.com.*\.(png|gif) 10080 80% > 10080 override-expire ignore-reload refresh_pattern garena\.com > 10080 80% 10080 override-expire reload-into-ims refresh_pattern > photobucket.*\.(jp(e?g|e|2)|tiff?|bmp|gif|png) 10080 80% > 10080 override-expire ignore-reload refresh_pattern > vid\.akm\.dailymotion\.com.*\.on2\? 10080 80% > 10080 ignore-no-cache override-expire override-lastmod refresh_pattern > mediafire.com\/images.*\.(jp(e?g|e|2)|tiff?|bmp|gif|png) 10080 80% > 10080 reload-into-ims override-expire ignore-private refresh_pattern > ^http:\/\/images|pics|thumbs[0-9]\. 10080 80% > 10080 reload-into-ims ignore-no-cache ignore-reload override-expire > refresh_pattern ^http:\/\/www.onemanga.com.*\/ > 10080 80% 10080 reload-into-ims ignore-no-cache ignore-reload > override-expire refresh_pattern > ^http://v\.okezone\.com/get_video\/([a-zA-Z0-9]) 10080 80% 10080 > override-expire ignore-reload ignore-no-cache ignore-private > ignore-auth override-lastmod negative-ttl=10080 > > #images facebook refresh_pattern -i \.facebook.com.*\.(jpg|png|gif) 10080 80% 10080 ignore-reload override-expire ignore-no-cache > refresh_pattern -i \.fbcdn.net.*\.(jpg|gif|png|swf|mp3) > 10080 80% 10080 ignore-reload override-expire ignore-no-cache > refresh_pattern static\.ak\.fbcdn\.net*\.(jpg|gif|png) > 10080 80% 10080 ignore-reload override-expire ignore-no-cache > refresh_pattern ^http:\/\/profile\.ak\.fbcdn.net*\.(jpg|gif|png) > 10080 80% 10080 ignore-reload override-expire ignore-no-cache > > #All File refresh_pattern -i \.(3gp|7z|ace|asx|bin|deb|divx|dvr-ms|ram|rpm|exe|inc|cab|qt) > 10080 80% 10080 ignore-no-cache override-expire override-lastmod > reload-into-ims refresh_pattern -i > \.(rar|jar|gz|tgz|bz2|iso|m1v|m2(v|p)|mo(d|v)|arj|lha|lzh|zip|tar) > 10080 80% 10080 ignore-no-cache override-expire override-lastmod > reload-into-ims refresh_pattern -i > \.(jp(e?g|e|2)|gif|pn[pg]|bm?|tiff?|ico|swf|dat|ad|txt|dll) > 10080 80% 10080 ignore-no-cache override-expire override-lastmod > reload-into-ims refresh_pattern -i > \.(avi|ac4|mp(e?g|a|e|1|2|3|4)|mk(a|v)|ms(i|u|p)|og(x|v|a|g)|rm|r(a|p)m|snd|vob) > 10080 80% 10080 ignore-no-cache override-expire override-lastmod > reload-into-ims refresh_pattern -i > \.(pp(t?x)|s|t)|pdf|rtf|wax|wm(a|v)|wmx|wpl|cb(r|z|t)|xl(s?x)|do(c?x)|flv|x-flv) > 10080 80% 10080 ignore-no-cache override-expire override-lastmod > reload-into-ims > > refresh_pattern -i (/cgi-bin/|\?) 0 0% 0 refresh_pattern ^gopher: > 1440 0% 1440 refresh_pattern ^ftp: 10080 95% 10080 > override-lastmod reload-into-ims refresh_pattern . 1440 > 95% 10080 override-lastmod reload-into-ims

Read the article
What's New in ASP.NET 4

- by Navaneeth

The .NET Framework version 4 includes enhancements for ASP.NET 4 in targeted areas. Visual Studio 2010 and Microsoft Visual Web Developer Express also include enhancements and new features for improved Web development. This document provides an overview of many of the new features that are included in the upcoming release. This topic contains the following sections: ASP.NET Core Services ASP.NET Web Forms ASP.NET MVC Dynamic Data ASP.NET Chart Control Visual Web Developer Enhancements Web Application Deployment with Visual Studio 2010 Enhancements to ASP.NET Multi-Targeting ASP.NET Core Services ASP.NET 4 introduces many features that improve core ASP.NET services such as output caching and session state storage. Extensible Output Caching Since the time that ASP.NET 1.0 was released, output caching has enabled developers to store the generated output of pages, controls, and HTTP responses in memory. On subsequent Web requests, ASP.NET can serve content more quickly by retrieving the generated output from memory instead of regenerating the output from scratch. However, this approach has a limitation — generated content always has to be stored in memory. On servers that experience heavy traffic, the memory requirements for output caching can compete with memory requirements for other parts of a Web application. ASP.NET 4 adds extensibility to output caching that enables you to configure one or more custom output-cache providers. Output-cache providers can use any storage mechanism to persist HTML content. These storage options can include local or remote disks, cloud storage, and distributed cache engines. Output-cache provider extensibility in ASP.NET 4 lets you design more aggressive and more intelligent output-caching strategies for Web sites. For example, you can create an output-cache provider that caches the "Top 10" pages of a site in memory, while caching pages that get lower traffic on disk. Alternatively, you can cache every vary-by combination for a rendered page, but use a distributed cache so that the memory consumption is offloaded from front-end Web servers. You create a custom output-cache provider as a class that derives from the OutputCacheProvider type. You can then configure the provider in the Web.config file by using the new providers subsection of the outputCache element For more information and for examples that show how to configure the output cache, see outputCache Element for caching (ASP.NET Settings Schema). For more information about the classes that support caching, see the documentation for the OutputCache and OutputCacheProvider classes. By default, in ASP.NET 4, all HTTP responses, rendered pages, and controls use the in-memory output cache. The defaultProvider attribute for ASP.NET is AspNetInternalProvider. You can change the default output-cache provider used for a Web application by specifying a different provider name for defaultProvider attribute. In addition, you can select different output-cache providers for individual control and for individual requests and programmatically specify which provider to use. For more information, see the HttpApplication.GetOutputCacheProviderName(HttpContext) method. The easiest way to choose a different output-cache provider for different Web user controls is to do so declaratively by using the new providerName attribute in a page or control directive, as shown in the following example: <%@ OutputCache Duration="60" VaryByParam="None" providerName="DiskCache" %> Preloading Web Applications Some Web applications must load large amounts of data or must perform expensive initialization processing before serving the first request. In earlier versions of ASP.NET, for these situations you had to devise custom approaches to "wake up" an ASP.NET application and then run initialization code during the Application_Load method in the Global.asax file. To address this scenario, a new application preload manager (autostart feature) is available when ASP.NET 4 runs on IIS 7.5 on Windows Server 2008 R2. The preload feature provides a controlled approach for starting up an application pool, initializing an ASP.NET application, and then accepting HTTP requests. It lets you perform expensive application initialization prior to processing the first HTTP request. For example, you can use the application preload manager to initialize an application and then signal a load-balancer that the application was initialized and ready to accept HTTP traffic. To use the application preload manager, an IIS administrator sets an application pool in IIS 7.5 to be automatically started by using the following configuration in the applicationHost.config file: <applicationPools> <add name="MyApplicationPool" startMode="AlwaysRunning" /> </applicationPools> Because a single application pool can contain multiple applications, you specify individual applications to be automatically started by using the following configuration in the applicationHost.config file: <sites> <site name="MySite" id="1"> <application path="/" serviceAutoStartEnabled="true" serviceAutoStartProvider="PrewarmMyCache" >  </application> </site> </sites>  <serviceAutoStartProviders> <add name="PrewarmMyCache" type="MyNamespace.CustomInitialization, MyLibrary" /> </serviceAutoStartProviders> When an IIS 7.5 server is cold-started or when an individual application pool is recycled, IIS 7.5 uses the information in the applicationHost.config file to determine which Web applications have to be automatically started. For each application that is marked for preload, IIS7.5 sends a request to ASP.NET 4 to start the application in a state during which the application temporarily does not accept HTTP requests. When it is in this state, ASP.NET instantiates the type defined by the serviceAutoStartProvider attribute (as shown in the previous example) and calls into its public entry point. You create a managed preload type that has the required entry point by implementing the IProcessHostPreloadClient interface, as shown in the following example: public class CustomInitialization : System.Web.Hosting.IProcessHostPreloadClient { public void Preload(string[] parameters) { // Perform initialization. } } After your initialization code runs in the Preload method and after the method returns, the ASP.NET application is ready to process requests. Permanently Redirecting a Page Content in Web applications is often moved over the lifetime of the application. This can lead to links to be out of date, such as the links that are returned by search engines. In ASP.NET, developers have traditionally handled requests to old URLs by using the Redirect method to forward a request to the new URL. However, the Redirect method issues an HTTP 302 (Found) response (which is used for a temporary redirect). This results in an extra HTTP round trip. ASP.NET 4 adds a RedirectPermanent helper method that makes it easy to issue HTTP 301 (Moved Permanently) responses, as in the following example: RedirectPermanent("/newpath/foroldcontent.aspx"); Search engines and other user agents that recognize permanent redirects will store the new URL that is associated with the content, which eliminates the unnecessary round trip made by the browser for temporary redirects. Session State Compression By default, ASP.NET provides two options for storing session state across a Web farm. The first option is a session state provider that invokes an out-of-process session state server. The second option is a session state provider that stores data in a Microsoft SQL Server database. Because both options store state information outside a Web application's worker process, session state has to be serialized before it is sent to remote storage. If a large amount of data is saved in session state, the size of the serialized data can become very large. ASP.NET 4 introduces a new compression option for both kinds of out-of-process session state providers. By using this option, applications that have spare CPU cycles on Web servers can achieve substantial reductions in the size of serialized session state data. You can set this option using the new compressionEnabled attribute of the sessionState element in the configuration file. When the compressionEnabled configuration option is set to true, ASP.NET compresses (and decompresses) serialized session state by using the .NET Framework GZipStreamclass. The following example shows how to set this attribute. <sessionState mode="SqlServer" sqlConnectionString="data source=dbserver;Initial Catalog=aspnetstate" allowCustomSqlDatabase="true" compressionEnabled="true" /> ASP.NET Web Forms Web Forms has been a core feature in ASP.NET since the release of ASP.NET 1.0. Many enhancements have been in this area for ASP.NET 4, such as the following: The ability to set meta tags. More control over view state. Support for recently introduced browsers and devices. Easier ways to work with browser capabilities. Support for using ASP.NET routing with Web Forms. More control over generated IDs. The ability to persist selected rows in data controls. More control over rendered HTML in the FormView and ListView controls. Filtering support for data source controls. Enhanced support for Web standards and accessibility Setting Meta Tags with the Page.MetaKeywords and Page.MetaDescription Properties Two properties have been added to the Page class: MetaKeywords and MetaDescription. These two properties represent corresponding meta tags in the HTML rendered for a page, as shown in the following example: <head id="Head1" runat="server"> <title>Untitled Page</title> <meta name="keywords" content="keyword1, keyword2' /> <meta name="description" content="Description of my page" /> </head> These two properties work like the Title property does, and they can be set in the @ Page directive. For more information, see Page.MetaKeywords and Page.MetaDescription. Enabling View State for Individual Controls A new property has been added to the Control class: ViewStateMode. You can use this property to disable view state for all controls on a page except those for which you explicitly enable view state. View state data is included in a page's HTML and increases the amount of time it takes to send a page to the client and post it back. Storing more view state than is necessary can cause significant decrease in performance. In earlier versions of ASP.NET, you could reduce the impact of view state on a page's performance by disabling view state for specific controls. But sometimes it is easier to enable view state for a few controls that need it instead of disabling it for many that do not need it. For more information, see Control.ViewStateMode. Support for Recently Introduced Browsers and Devices ASP.NET includes a feature that is named browser capabilities that lets you determine the capabilities of the browser that a user is using. Browser capabilities are represented by the HttpBrowserCapabilities object which is stored in the HttpRequest.Browser property. Information about a particular browser's capabilities is defined by a browser definition file. In ASP.NET 4, these browser definition files have been updated to contain information about recently introduced browsers and devices such as Google Chrome, Research in Motion BlackBerry smart phones, and Apple iPhone. Existing browser definition files have also been updated. For more information, see How to: Upgrade an ASP.NET Web Application to ASP.NET 4 and ASP.NET Web Server Controls and Browser Capabilities. The browser definition files that are included with ASP.NET 4 are shown in the following list: •blackberry.browser •chrome.browser •Default.browser •firefox.browser •gateway.browser •generic.browser •ie.browser •iemobile.browser •iphone.browser •opera.browser •safari.browser A New Way to Define Browser Capabilities ASP.NET 4 includes a new feature referred to as browser capabilities providers. As the name suggests, this lets you build a provider that in turn lets you write custom code to determine browser capabilities. In ASP.NET version 3.5 Service Pack 1, you define browser capabilities in an XML file. This file resides in a machine-level folder or an application-level folder. Most developers do not need to customize these files, but for those who do, the provider approach can be easier than dealing with complex XML syntax. The provider approach makes it possible to simplify the process by implementing a common browser definition syntax, or a database that contains up-to-date browser definitions, or even a Web service for such a database. For more information about the new browser capabilities provider, see the What's New for ASP.NET 4 White Paper. Routing in ASP.NET 4 ASP.NET 4 adds built-in support for routing with Web Forms. Routing is a feature that was introduced with ASP.NET 3.5 SP1 and lets you configure an application to use URLs that are meaningful to users and to search engines because they do not have to specify physical file names. This can make your site more user-friendly and your site content more discoverable by search engines. For example, the URL for a page that displays product categories in your application might look like the following example: http://website/products.aspx?categoryid=12 By using routing, you can use the following URL to render the same information: http://website/products/software The second URL lets the user know what to expect and can result in significantly improved rankings in search engine results. the new features include the following: The PageRouteHandler class is a simple HTTP handler that you use when you define routes. You no longer have to write a custom route handler. The HttpRequest.RequestContext and Page.RouteData properties make it easier to access information that is passed in URL parameters. The RouteUrl expression provides a simple way to create a routed URL in markup. The RouteValue expression provides a simple way to extract URL parameter values in markup. The RouteParameter class makes it easier to pass URL parameter values to a query for a data source control (similar to FormParameter). You no longer have to change the Web.config file to enable routing. For more information about routing, see the following topics: ASP.NET Routing Walkthrough: Using ASP.NET Routing in a Web Forms Application How to: Define Routes for Web Forms Applications How to: Construct URLs from Routes How to: Access URL Parameters in a Routed Page Setting Client IDs The new ClientIDMode property makes it easier to write client script that references HTML elements rendered for server controls. Increasing use of Microsoft Ajax makes the need to do this more common. For example, you may have a data control that renders a long list of products with prices and you want to use client script to make a Web service call and update individual prices in the list as they change without refreshing the entire page. Typically you get a reference to an HTML element in client script by using the document.GetElementById method. You pass to this method the value of the id attribute of the HTML element you want to reference. In the case of elements that are rendered for ASP.NET server controls earlier versions of ASP.NET could make this difficult or impossible. You were not always able to predict what id values ASP.NET would generate, or ASP.NET could generate very long id values. The problem was especially difficult for data controls that would generate multiple rows for a single instance of the control in your markup. ASP.NET 4 adds two new algorithms for generating id attributes. These algorithms can generate id attributes that are easier to work with in client script because they are more predictable and that are easier to work with because they are simpler. For more information about how to use the new algorithms, see the following topics: ASP.NET Web Server Control Identification Walkthrough: Making Data-Bound Controls Easier to Access from JavaScript Walkthrough: Making Controls Located in Web User Controls Easier to Access from JavaScript How to: Access Controls from JavaScript by ID Persisting Row Selection in Data Controls The GridView and ListView controls enable users to select a row. In previous versions of ASP.NET, row selection was based on the row index on the page. For example, if you select the third item on page 1 and then move to page 2, the third item on page 2 is selected. In most cases, is more desirable not to select any rows on page 2. ASP.NET 4 supports Persisted Selection, a new feature that was initially supported only in Dynamic Data projects in the .NET Framework 3.5 SP1. When this feature is enabled, the selected item is based on the row data key. This means that if you select the third row on page 1 and move to page 2, nothing is selected on page 2. When you move back to page 1, the third row is still selected. This is a much more natural behavior than the behavior in earlier versions of ASP.NET. Persisted selection is now supported for the GridView and ListView controls in all projects. You can enable this feature in the GridView control, for example, by setting the EnablePersistedSelection property, as shown in the following example: <asp:GridView id="GridView2" runat="server" PersistedSelection="true"> </asp:GridView> FormView Control Enhancements The FormView control is enhanced to make it easier to style the content of the control with CSS. In previous versions of ASP.NET, the FormView control rendered it contents using an item template. This made styling more difficult in the markup because unexpected table row and table cell tags were rendered by the control. The FormView control supports RenderOuterTable, a property in ASP.NET 4. When this property is set to false, as show in the following example, the table tags are not rendered. This makes it easier to apply CSS style to the contents of the control. <asp:FormView ID="FormView1" runat="server" RenderTable="false"> For more information, see FormView Web Server Control Overview. ListView Control Enhancements The ListView control, which was introduced in ASP.NET 3.5, has all the functionality of the GridView control while giving you complete control over the output. This control has been made easier to use in ASP.NET 4. The earlier version of the control required that you specify a layout template that contained a server control with a known ID. The following markup shows a typical example of how to use the ListView control in ASP.NET 3.5. <asp:ListView ID="ListView1" runat="server"> <LayoutTemplate> <asp:PlaceHolder ID="ItemPlaceHolder" runat="server"></asp:PlaceHolder> </LayoutTemplate> <ItemTemplate> <% Eval("LastName")%> </ItemTemplate> </asp:ListView> In ASP.NET 4, the ListView control does not require a layout template. The markup shown in the previous example can be replaced with the following markup: <asp:ListView ID="ListView1" runat="server"> <ItemTemplate> <% Eval("LastName")%> </ItemTemplate> </asp:ListView> For more information, see ListView Web Server Control Overview. Filtering Data with the QueryExtender Control A very common task for developers who create data-driven Web pages is to filter data. This traditionally has been performed by building Where clauses in data source controls. This approach can be complicated, and in some cases the Where syntax does not let you take advantage of the full functionality of the underlying database. To make filtering easier, a new QueryExtender control has been added in ASP.NET 4. This control can be added to EntityDataSource or LinqDataSource controls in order to filter the data returned by these controls. Because the QueryExtender control relies on LINQ, but you do not to need to know how to write LINQ queries to use the query extender. The QueryExtender control supports a variety of filter options. The following lists QueryExtender filter options. Term Definition SearchExpression Searches a field or fields for string values and compares them to a specified string value. RangeExpression Searches a field or fields for values in a range specified by a pair of values. PropertyExpression Compares a specified value to a property value in a field. If the expression evaluates to true, the data that is being examined is returned. OrderByExpression Sorts data by a specified column and sort direction. CustomExpression Calls a function that defines custom filter in the page. For more information, see QueryExtenderQueryExtender Web Server Control Overview. Enhanced Support for Web Standards and Accessibility Earlier versions of ASP.NET controls sometimes render markup that does not conform to HTML, XHTML, or accessibility standards. ASP.NET 4 eliminates most of these exceptions. For details about how the HTML that is rendered by each control meets accessibility standards, see ASP.NET Controls and Accessibility. CSS for Controls that Can be Disabled In ASP.NET 3.5, when a control is disabled (see WebControl.Enabled), a disabled attribute is added to the rendered HTML element. For example, the following markup creates a Label control that is disabled: <asp:Label id="Label1" runat="server" Text="Test" Enabled="false" /> In ASP.NET 3.5, the previous control settings generate the following HTML: <span id="Label1" disabled="disabled">Test</span> In HTML 4.01, the disabled attribute is not considered valid on span elements. It is valid only on input elements because it specifies that they cannot be accessed. On display-only elements such as span elements, browsers typically support rendering for a disabled appearance, but a Web page that relies on this non-standard behavior is not robust according to accessibility standards. For display-only elements, you should use CSS to indicate a disabled visual appearance. Therefore, by default ASP.NET 4 generates the following HTML for the control settings shown previously: <span id="Label1" class="aspNetDisabled">Test</span> You can change the value of the class attribute that is rendered by default when a control is disabled by setting the DisabledCssClass property. CSS for Validation Controls In ASP.NET 3.5, validation controls render a default color of red as an inline style. For example, the following markup creates a RequiredFieldValidator control: <asp:RequiredFieldValidator ID="RequiredFieldValidator1" runat="server" ErrorMessage="Required Field" ControlToValidate="RadioButtonList1" /> ASP.NET 3.5 renders the following HTML for the validator control: <span id="RequiredFieldValidator1" style="color:Red;visibility:hidden;">RequiredFieldValidator</span> By default, ASP.NET 4 does not render an inline style to set the color to red. An inline style is used only to hide or show the validator, as shown in the following example: <span id="RequiredFieldValidator1" style"visibility:hidden;">RequiredFieldValidator</span> Therefore, ASP.NET 4 does not automatically show error messages in red. For information about how to use CSS to specify a visual style for a validation control, see Validating User Input in ASP.NET Web Pages. CSS for the Hidden Fields Div Element ASP.NET uses hidden fields to store state information such as view state and control state. These hidden fields are contained by a div element. In ASP.NET 3.5, this div element does not have a class attribute or an id attribute. Therefore, CSS rules that affect all div elements could unintentionally cause this div to be visible. To avoid this problem, ASP.NET 4 renders the div element for hidden fields with a CSS class that you can use to differentiate the hidden fields div from others. The new classvalue is shown in the following example: <div class="aspNetHidden"> CSS for the Table, Image, and ImageButton Controls By default, in ASP.NET 3.5, some controls set the border attribute of rendered HTML to zero (0). The following example shows HTML that is generated by the Table control in ASP.NET 3.5: <table id="Table2" border="0"> The Image control and the ImageButton control also do this. Because this is not necessary and provides visual formatting information that should be provided by using CSS, the attribute is not generated in ASP.NET 4. CSS for the UpdatePanel and UpdateProgress Controls In ASP.NET 3.5, the UpdatePanel and UpdateProgress controls do not support expando attributes. This makes it impossible to set a CSS class on the HTMLelements that they render. In ASP.NET 4 these controls have been changed to accept expando attributes, as shown in the following example: <asp:UpdatePanel runat="server" class="myStyle"> </asp:UpdatePanel> The following HTML is rendered for this markup: <div id="ctl00_MainContent_UpdatePanel1" class="expandoclass"> </div> Eliminating Unnecessary Outer Tables In ASP.NET 3.5, the HTML that is rendered for the following controls is wrapped in a table element whose purpose is to apply inline styles to the entire control: FormView Login PasswordRecovery ChangePassword If you use templates to customize the appearance of these controls, you can specify CSS styles in the markup that you provide in the templates. In that case, no extra outer table is required. In ASP.NET 4, you can prevent the table from being rendered by setting the new RenderOuterTable property to false. Layout Templates for Wizard Controls In ASP.NET 3.5, the Wizard and CreateUserWizard controls generate an HTML table element that is used for visual formatting. In ASP.NET 4 you can use a LayoutTemplate element to specify the layout. If you do this, the HTML table element is not generated. In the template, you create placeholder controls to indicate where items should be dynamically inserted into the control. (This is similar to how the template model for the ListView control works.) For more information, see the Wizard.LayoutTemplate property. New HTML Formatting Options for the CheckBoxList and RadioButtonList Controls ASP.NET 3.5 uses HTML table elements to format the output for the CheckBoxList and RadioButtonList controls. To provide an alternative that does not use tables for visual formatting, ASP.NET 4 adds two new options to the RepeatLayout enumeration: UnorderedList. This option causes the HTML output to be formatted by using ul and li elements instead of a table. OrderedList. This option causes the HTML output to be formatted by using ol and li elements instead of a table. For examples of HTML that is rendered for the new options, see the RepeatLayout enumeration. Header and Footer Elements for the Table Control In ASP.NET 3.5, the Table control can be configured to render thead and tfoot elements by setting the TableSection property of the TableHeaderRow class and the TableFooterRow class. In ASP.NET 4 these properties are set to the appropriate values by default. CSS and ARIA Support for the Menu Control In ASP.NET 3.5, the Menu control uses HTML table elements for visual formatting, and in some configurations it is not keyboard-accessible. ASP.NET 4 addresses these problems and improves accessibility in the following ways: The generated HTML is structured as an unordered list (ul and li elements). CSS is used for visual formatting. The menu behaves in accordance with ARIA standards for keyboard access. You can use arrow keys to navigate menu items. (For information about ARIA, see Accessibility in Visual Studio and ASP.NET.) ARIA role and property attributes are added to the generated HTML. (Attributes are added by using JavaScript instead of included in the HTML, to avoid generating HTML that would cause markup validation errors.) Styles for the Menu control are rendered in a style block at the top of the page, instead of inline with the rendered HTML elements. If you want to use a separate CSS file so that you can modify the menu styles, you can set the Menu control's new IncludeStyleBlock property to false, in which case the style block is not generated. Valid XHTML for the HtmlForm Control In ASP.NET 3.5, the HtmlForm control (which is created implicitly by the <form runat="server"> tag) renders an HTML form element that has both name and id attributes. The name attribute is deprecated in XHTML 1.1. Therefore, this control does not render the name attribute in ASP.NET 4. Maintaining Backward Compatibility in Control Rendering An existing ASP.NET Web site might have code in it that assumes that controls are rendering HTML the way they do in ASP.NET 3.5. To avoid causing backward compatibility problems when you upgrade the site to ASP.NET 4, you can have ASP.NET continue to generate HTML the way it does in ASP.NET 3.5 after you upgrade the site. To do so, you can set the controlRenderingCompatibilityVersion attribute of the pages element to "3.5" in the Web.config file of an ASP.NET 4 Web site, as shown in the following example: <system.web> <pages controlRenderingCompatibilityVersion="3.5"/> </system.web> If this setting is omitted, the default value is the same as the version of ASP.NET that the Web site targets. (For information about multi-targeting in ASP.NET, see .NET Framework Multi-Targeting for ASP.NET Web Projects.) ASP.NET MVC ASP.NET MVC helps Web developers build compelling standards-based Web sites that are easy to maintain because it decreases the dependency among application layers by using the Model-View-Controller (MVC) pattern. MVC provides complete control over the page markup. It also improves testability by inherently supporting Test Driven Development (TDD). Web sites created using ASP.NET MVC have a modular architecture. This allows members of a team to work independently on the various modules and can be used to improve collaboration. For example, developers can work on the model and controller layers (data and logic), while the designer work on the view (presentation). For tutorials, walkthroughs, conceptual content, code samples, and a complete API reference, see ASP.NET MVC 2. Dynamic Data Dynamic Data was introduced in the .NET Framework 3.5 SP1 release in mid-2008. This feature provides many enhancements for creating data-driven applications, such as the following: A RAD experience for quickly building a data-driven Web site. Automatic validation that is based on constraints defined in the data model. The ability to easily change the markup that is generated for fields in the GridView and DetailsView controls by using field templates that are part of your Dynamic Data project. For ASP.NET 4, Dynamic Data has been enhanced to give developers even more power for quickly building data-driven Web sites. For more information, see ASP.NET Dynamic Data Content Map. Enabling Dynamic Data for Individual Data-Bound Controls in Existing Web Applications You can use Dynamic Data features in existing ASP.NET Web applications that do not use scaffolding by enabling Dynamic Data for individual data-bound controls. Dynamic Data provides the presentation and data layer support for rendering these controls. When you enable Dynamic Data for data-bound controls, you get the following benefits: Setting default values for data fields. Dynamic Data enables you to provide default values at run time for fields in a data control. Interacting with the database without creating and registering a data model. Automatically validating the data that is entered by the user without writing any code. For more information, see Walkthrough: Enabling Dynamic Data in ASP.NET Data-Bound Controls. New Field Templates for URLs and E-mail Addresses ASP.NET 4 introduces two new built-in field templates, EmailAddress.ascx and Url.ascx. These templates are used for fields that are marked as EmailAddress or Url using the DataTypeAttribute attribute. For EmailAddress objects, the field is displayed as a hyperlink that is created by using the mailto: protocol. When users click the link, it opens the user's e-mail client and creates a skeleton message. Objects typed as Url are displayed as ordinary hyperlinks. The following example shows how to mark fields. [DataType(DataType.EmailAddress)] public object HomeEmail { get; set; } [DataType(DataType.Url)] public object Website { get; set; } Creating Links with the DynamicHyperLink Control Dynamic Data uses the new routing feature that was added in the .NET Framework 3.5 SP1 to control the URLs that users see when they access the Web site. The new DynamicHyperLink control makes it easy to build links to pages in a Dynamic Data site. For information, see How to: Create Table Action Links in Dynamic Data Support for Inheritance in the Data Model Both the ADO.NET Entity Framework and LINQ to SQL support inheritance in their data models. An example of this might be a database that has an InsurancePolicy table. It might also contain CarPolicy and HousePolicy tables that have the same fields as InsurancePolicy and then add more fields. Dynamic Data has been modified to understand inherited objects in the data model and to support scaffolding for the inherited tables. For more information, see Walkthrough: Mapping Table-per-Hierarchy Inheritance in Dynamic Data. Support for Many-to-Many Relationships (Entity Framework Only) The Entity Framework has rich support for many-to-many relationships between tables, which is implemented by exposing the relationship as a collection on an Entity object. New field templates (ManyToMany.ascx and ManyToMany_Edit.ascx) have been added to provide support for displaying and editing data that is involved in many-to-many relationships. For more information, see Working with Many-to-Many Data Relationships in Dynamic Data. New Attributes to Control Display and Support Enumerations The DisplayAttribute has been added to give you additional control over how fields are displayed. The DisplayNameAttribute attribute in earlier versions of Dynamic Data enabled you to change the name that is used as a caption for a field. The new DisplayAttribute class lets you specify more options for displaying a field, such as the order in which a field is displayed and whether a field will be used as a filter. The attribute also provides independent control of the name that is used for the labels in a GridView control, the name that is used in a DetailsView control, the help text for the field, and the watermark used for the field (if the field accepts text input). The EnumDataTypeAttribute class has been added to let you map fields to enumerations. When you apply this attribute to a field, you specify an enumeration type. Dynamic Data uses the new Enumeration.ascx field template to create UI for displaying and editing enumeration values. The template maps the values from the database to the names in the enumeration. Enhanced Support for Filters Dynamic Data 1.0 had built-in filters for Boolean columns and foreign-key columns. The filters did not let you specify the order in which they were displayed. The new DisplayAttribute attribute addresses this by giving you control over whether a column appears as a filter and in what order it will be displayed. An additional enhancement is that filtering support has been rewritten to use the new QueryExtender feature of Web Forms. This lets you create filters without requiring knowledge of the data source control that the filters will be used with. Along with these extensions, filters have also been turned into template controls, which lets you add new ones. Finally, the DisplayAttribute class mentioned earlier allows the default filter to be overridden, in the same way that UIHint allows the default field template for a column to be overridden. For more information, see Walkthrough: Filtering Rows in Tables That Have a Parent-Child Relationship and QueryableFilterRepeater. ASP.NET Chart Control The ASP.NET chart server control enables you to create ASP.NET pages applications that have simple, intuitive charts for complex statistical or financial analysis. The chart control supports the following features: Data series, chart areas, axes, legends, labels, titles, and more. Data binding. Data manipulation, such as copying, splitting, merging, alignment, grouping, sorting, searching, and filtering. Statistical formulas and financial formulas. Advanced chart appearance, such as 3-D, anti-aliasing, lighting, and perspective. Events and customizations. Interactivity and Microsoft Ajax. Support for the Ajax Content Delivery Network (CDN), which provides an optimized way for you to add Microsoft Ajax Library and jQuery scripts to your Web applications. For more information, see Chart Web Server Control Overview. Visual Web Developer Enhancements The following sections provide information about enhancements and new features in Visual Studio 2010 and Visual Web Developer Express. The Web page designer in Visual Studio 2010 has been enhanced for better CSS compatibility, includes additional support for HTML and ASP.NET markup snippets, and features a redesigned version of IntelliSense for JScript. Improved CSS Compatibility The Visual Web Developer designer in Visual Studio 2010 has been updated to improve CSS 2.1 standards compliance. The designer better preserves HTML source code and is more robust than in previous versions of Visual Studio. HTML and JScript Snippets In the HTML editor, IntelliSense auto-completes tag names. The IntelliSense Snippets feature auto-completes whole tags and more. In Visual Studio 2010, IntelliSense snippets are supported for JScript, alongside C# and Visual Basic, which were supported in earlier versions of Visual Studio. Visual Studio 2010 includes over 200 snippets that help you auto-complete common ASP.NET and HTML tags, including required attributes (such as runat="server") and common attributes specific to a tag (such as ID, DataSourceID, ControlToValidate, and Text). You can download additional snippets, or you can write your own snippets that encapsulate the blocks of markup that you or your team use for common tasks. For more information on HTML snippets, see Walkthrough: Using HTML Snippets. JScript IntelliSense Enhancements In Visual 2010, JScript IntelliSense has been redesigned to provide an even richer editing experience. IntelliSense now recognizes objects that have been dynamically generated by methods such as registerNamespace and by similar techniques used by other JavaScript frameworks. Performance has been improved to analyze large libraries of script and to display IntelliSense with little or no processing delay. Compatibility has been significantly increased to support almost all third-party libraries and to support diverse coding styles. Documentation comments are now parsed as you type and are immediately leveraged by IntelliSense. Web Application Deployment with Visual Studio 2010 For Web application projects, Visual Studio now provides tools that work with the IIS Web Deployment Tool (Web Deploy) to automate many processes that had to be done manually in earlier versions of ASP.NET. For example, the following tasks can now be automated: Creating an IIS application on the destination computer and configuring IIS settings. Copying files to the destination computer. Changing Web.config settings that must be different in the destination environment. Propagating changes to data or data structures in SQL Server databases that are used by the Web application. For more information about Web application deployment, see ASP.NET Deployment Content Map. Enhancements to ASP.NET Multi-Targeting ASP.NET 4 adds new features to the multi-targeting feature to make it easier to work with projects that target earlier versions of the .NET Framework. Multi-targeting was introduced in ASP.NET 3.5 to enable you to use the latest version of Visual Studio without having to upgrade existing Web sites or Web services to the latest version of the .NET Framework. In Visual Studio 2008, when you work with a project targeted for an earlier version of the .NET Framework, most features of the development environment adapt to the targeted version. However, IntelliSense displays language features that are available in the current version, and property windows display properties available in the current version. In Visual Studio 2010, only language features and properties available in the targeted version of the .NET Framework are shown. For more information about multi-targeting, see the following topics: .NET Framework Multi-Targeting for ASP.NET Web Projects ASP.NET Side-by-Side Execution Overview How to: Host Web Applications That Use Different Versions of the .NET Framework on the Same Server How to: Deploy Web Site Projects Targeted for Earlier Versions of the .NET Framework

Read the article
mac, netbeans 6.8, c++, sdl, opengl: compilation problems

- by ufk

Hiya. I'm trying to properly compile a c++ opengl+sdl application using netbeans 6.8 under Snow Leopard 64-bit. I have libSDL 1.2.14 installed using macports. The script that I try to compile is the following: #ifdef WIN32 #define WIN32_LEAN_AND_MEAN #include <windows.h> #endif #if defined(__APPLE__) && defined(__MACH__) #include <OpenGL/gl.h> // Header File For The OpenGL32 Library #include <OpenGL/glu.h> // Header File For The GLu32 Library #else #include <GL/gl.h> // Header File For The OpenGL32 Library #include <GL/glu.h> // Header File For The GLu32 Library #endif #include "sdl/SDL.h" #include <stdio.h> #include <unistd.h> #include "SDL/SDL_main.h" SDL_Surface *screen=NULL; GLfloat rtri; // Angle For The Triangle ( NEW ) GLfloat rquad; // Angle For The Quad ( NEW ) void InitGL(int Width, int Height) // We call this right after our OpenGL window is created. { glViewport(0, 0, Width, Height); glClearColor(0.0f, 0.0f, 0.0f, 0.0f); // This Will Clear The Background Color To Black glClearDepth(1.0); // Enables Clearing Of The Depth Buffer glDepthFunc(GL_LESS); // The Type Of Depth Test To Do glEnable(GL_DEPTH_TEST); // Enables Depth Testing glShadeModel(GL_SMOOTH); // Enables Smooth Color Shading glMatrixMode(GL_PROJECTION); glLoadIdentity(); // Reset The Projection Matrix gluPerspective(45.0f,(GLfloat)Width/(GLfloat)Height,0.1f,100.0f); // Calculate The Aspect Ratio Of The Window glMatrixMode(GL_MODELVIEW); } /* The main drawing function. */ int DrawGLScene() { glClear(GL_COLOR_BUFFER_BIT | GL_DEPTH_BUFFER_BIT); // Clear The Screen And The Depth Buffer glLoadIdentity(); // Reset The View glTranslatef(-1.5f,0.0f,-6.0f); // Move Left 1.5 Units And Into The Screen 6.0 glRotatef(rtri,0.0f,1.0f,0.0f); // Rotate The Triangle On The Y axis ( NEW ) // draw a triangle glBegin(GL_TRIANGLES); // Begin Drawing Triangles glColor3f(1.0f,0.0f,0.0f); // Red glVertex3f( 0.0f, 1.0f, 0.0f); // Top Of Triangle (Front) glColor3f(0.0f,1.0f,0.0f); // Green glVertex3f(-1.0f,-1.0f, 1.0f); // Left Of Triangle (Front) glColor3f(0.0f,0.0f,1.0f); // Blue glVertex3f( 1.0f,-1.0f, 1.0f); // Right Of Triangle (Front) glColor3f(1.0f,0.0f,0.0f); // Red glVertex3f( 0.0f, 1.0f, 0.0f); // Top Of Triangle (Right) glColor3f(0.0f,0.0f,1.0f); // Blue glVertex3f( 1.0f,-1.0f, 1.0f); // Left Of Triangle (Right) glColor3f(0.0f,1.0f,0.0f); // Green glVertex3f( 1.0f,-1.0f, -1.0f); // Right Of Triangle (Right) glColor3f(1.0f,0.0f,0.0f); // Red glVertex3f( 0.0f, 1.0f, 0.0f); // Top Of Triangle (Back) glColor3f(0.0f,1.0f,0.0f); // Green glVertex3f( 1.0f,-1.0f, -1.0f); // Left Of Triangle (Back) glColor3f(0.0f,0.0f,1.0f); // Blue glVertex3f(-1.0f,-1.0f, -1.0f); // Right Of Triangle (Back) glColor3f(1.0f,0.0f,0.0f); // Red glVertex3f( 0.0f, 1.0f, 0.0f); // Top Of Triangle (Left) glColor3f(0.0f,0.0f,1.0f); // Blue glVertex3f(-1.0f,-1.0f,-1.0f); // Left Of Triangle (Left) glColor3f(0.0f,1.0f,0.0f); // Green glVertex3f(-1.0f,-1.0f, 1.0f); // Right Of Triangle (Left) glEnd(); glLoadIdentity(); // Reset The Current Modelview Matrix glTranslatef(1.5f,0.0f,-7.0f); // Move Right 1.5 Units And Into The Screen 6.0 glRotatef(rquad,1.0f,0.0f,0.0f); // Rotate The Quad On The X axis ( NEW ) glBegin(GL_QUADS); // Start Drawing Quads glColor3f(0.0f,1.0f,0.0f); // Set The Color To Green glVertex3f( 1.0f, 1.0f,-1.0f); // Top Right Of The Quad (Top) glVertex3f(-1.0f, 1.0f,-1.0f); // Top Left Of The Quad (Top) glVertex3f(-1.0f, 1.0f, 1.0f); // Bottom Left Of The Quad (Top) glVertex3f( 1.0f, 1.0f, 1.0f); // Bottom Right Of The Quad (Top) glColor3f(1.0f,0.5f,0.0f); // Set The Color To Orange glVertex3f( 1.0f,-1.0f, 1.0f); // Top Right Of The Quad (Bottom) glVertex3f(-1.0f,-1.0f, 1.0f); // Top Left Of The Quad (Bottom) glVertex3f(-1.0f,-1.0f,-1.0f); // Bottom Left Of The Quad (Bottom) glVertex3f( 1.0f,-1.0f,-1.0f); // Bottom Right Of The Quad (Bottom) glColor3f(1.0f,0.0f,0.0f); // Set The Color To Red glVertex3f( 1.0f, 1.0f, 1.0f); // Top Right Of The Quad (Front) glVertex3f(-1.0f, 1.0f, 1.0f); // Top Left Of The Quad (Front) glVertex3f(-1.0f,-1.0f, 1.0f); // Bottom Left Of The Quad (Front) glVertex3f( 1.0f,-1.0f, 1.0f); // Bottom Right Of The Quad (Front) glColor3f(1.0f,1.0f,0.0f); // Set The Color To Yellow glVertex3f( 1.0f,-1.0f,-1.0f); // Bottom Left Of The Quad (Back) glVertex3f(-1.0f,-1.0f,-1.0f); // Bottom Right Of The Quad (Back) glVertex3f(-1.0f, 1.0f,-1.0f); // Top Right Of The Quad (Back) glVertex3f( 1.0f, 1.0f,-1.0f); // Top Left Of The Quad (Back) glColor3f(0.0f,0.0f,1.0f); // Set The Color To Blue glVertex3f(-1.0f, 1.0f, 1.0f); // Top Right Of The Quad (Left) glVertex3f(-1.0f, 1.0f,-1.0f); // Top Left Of The Quad (Left) glVertex3f(-1.0f,-1.0f,-1.0f); // Bottom Left Of The Quad (Left) glVertex3f(-1.0f,-1.0f, 1.0f); // Bottom Right Of The Quad (Left) glColor3f(1.0f,0.0f,1.0f); // Set The Color To Violet glVertex3f( 1.0f, 1.0f,-1.0f); // Top Right Of The Quad (Right) glVertex3f( 1.0f, 1.0f, 1.0f); // Top Left Of The Quad (Right) glVertex3f( 1.0f,-1.0f, 1.0f); // Bottom Left Of The Quad (Right) glVertex3f( 1.0f,-1.0f,-1.0f); // Bottom Right Of The Quad (Right) glEnd(); // Done Drawing A Quad rtri+=0.02f; // Increase The Rotation Variable For The Triangle ( NEW ) rquad-=0.015f; // Decrease The Rotation Variable For The Quad ( NEW ) // swap buffers to display, since we're double buffered. SDL_GL_SwapBuffers(); return true; } int main(int argc,char* argv[]) { int done; /*variable to hold the file name of the image to be loaded *In real world error handling code would precede this */ /* Initialize SDL for video output */ if ( SDL_Init(SDL_INIT_VIDEO) < 0 ) { fprintf(stderr, "Unable to initialize SDL: %s\n", SDL_GetError()); exit(1); } atexit(SDL_Quit); /* Create a 640x480 OpenGL screen */ if ( SDL_SetVideoMode(640, 480, 0, SDL_OPENGL) == NULL ) { fprintf(stderr, "Unable to create OpenGL screen: %s\n", SDL_GetError()); SDL_Quit(); exit(2); } SDL_WM_SetCaption("another example",NULL); InitGL(640,480); done=0; while (! done) { DrawGLScene(); SDL_Event event; while ( SDL_PollEvent(&event) ) { if ( event.type == SDL_QUIT ) { done = 1; } if ( event.type == SDL_KEYDOWN ) { if ( event.key.keysym.sym == SDLK_ESCAPE ) { done = 1; } } } } } Under netbeans project properties I configured the following: C++ Compiler: added /usr/X11/include and /opt/local/include to the include directories. Linker: I added the following libraries: /usr/X11/lib/libGL.dylib /usr/X11/lib/libGLU.dylib /opt/local/lib/libSDL.dylib /opt/local/lib/libSDLmain.a Now... before I included SDL_main.h and libSDLMain.a to the project I got an error unknown reference to _main then I read here: http://www.libsdl.org/faq.php?action=listentries&category=7#55 that I need to include SDL_Main.h and to link libSDLMain.so to my project. after doing so, the project still won't compile. this is the Netbeans output: /usr/bin/make -f nbproject/Makefile-Debug.mk SUBPROJECTS= .clean-conf rm -f -r build/Debug rm -f dist/Debug/GNU-MacOSX/opengl2 CLEAN SUCCESSFUL (total time: 79ms) /usr/bin/make -f nbproject/Makefile-Debug.mk SUBPROJECTS= .build-conf /usr/bin/make -f nbproject/Makefile-Debug.mk dist/Debug/GNU-MacOSX/opengl2 mkdir -p build/Debug/GNU-MacOSX rm -f build/Debug/GNU-MacOSX/main.o.d g++ -c -g -I/usr/X11/include -I/opt/local/include -MMD -MP -MF build/Debug/GNU-MacOSX/main.o.d -o build/Debug/GNU-MacOSX/main.o main.cpp mkdir -p dist/Debug/GNU-MacOSX g++ -o dist/Debug/GNU-MacOSX/opengl2 build/Debug/GNU-MacOSX/main.o /opt/local/lib/libIL.dylib /opt/local/lib/libILU.dylib /opt/local/lib/libILUT.dylib /usr/X11/lib/libGL.dylib /usr/X11/lib/libGLU.dylib /opt/local/lib/libSDL.dylib /opt/local/lib/libSDLmain.a Undefined symbols: "_OBJC_CLASS_$_NSMenu", referenced from: __objc_classrefs__DATA@0 in libSDLmain.a(SDLMain.o) "__objc_empty_cache", referenced from: _OBJC_METACLASS_$_SDLMain in libSDLmain.a(SDLMain.o) _OBJC_CLASS_$_SDLMain in libSDLmain.a(SDLMain.o) "_CFBundleGetMainBundle", referenced from: -[SDLMain setupWorkingDirectory:] in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) "_CFURLGetFileSystemRepresentation", referenced from: -[SDLMain setupWorkingDirectory:] in libSDLmain.a(SDLMain.o) "_NSApp", referenced from: _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) "_OBJC_CLASS_$_NSProcessInfo", referenced from: __objc_classrefs__DATA@0 in libSDLmain.a(SDLMain.o) "_CFURLCreateCopyDeletingLastPathComponent", referenced from: -[SDLMain setupWorkingDirectory:] in libSDLmain.a(SDLMain.o) "_NSAllocateMemoryPages", referenced from: -[NSString(ReplaceSubString) stringByReplacingRange:with:] in libSDLmain.a(SDLMain.o) "___CFConstantStringClassReference", referenced from: cfstring=CFBundleName in libSDLmain.a(SDLMain.o) cfstring= in libSDLmain.a(SDLMain.o) cfstring=About in libSDLmain.a(SDLMain.o) cfstring=Hide in libSDLmain.a(SDLMain.o) cfstring=h in libSDLmain.a(SDLMain.o) cfstring=Hide Others in libSDLmain.a(SDLMain.o) cfstring=Show All in libSDLmain.a(SDLMain.o) cfstring=Quit in libSDLmain.a(SDLMain.o) cfstring=q in libSDLmain.a(SDLMain.o) cfstring=Window in libSDLmain.a(SDLMain.o) cfstring=m in libSDLmain.a(SDLMain.o) cfstring=Minimize in libSDLmain.a(SDLMain.o) "_OBJC_CLASS_$_NSAutoreleasePool", referenced from: __objc_classrefs__DATA@0 in libSDLmain.a(SDLMain.o) "_CPSEnableForegroundOperation", referenced from: _main in libSDLmain.a(SDLMain.o) "_CPSGetCurrentProcess", referenced from: _main in libSDLmain.a(SDLMain.o) "_CFBundleCopyBundleURL", referenced from: -[SDLMain setupWorkingDirectory:] in libSDLmain.a(SDLMain.o) "_NSDeallocateMemoryPages", referenced from: -[NSString(ReplaceSubString) stringByReplacingRange:with:] in libSDLmain.a(SDLMain.o) "_OBJC_CLASS_$_NSApplication", referenced from: l_OBJC_$_CATEGORY_NSApplication_$_SDLApplication in libSDLmain.a(SDLMain.o) __objc_classrefs__DATA@0 in libSDLmain.a(SDLMain.o) "_CPSSetFrontProcess", referenced from: _main in libSDLmain.a(SDLMain.o) "_OBJC_CLASS_$_NSString", referenced from: l_OBJC_$_CATEGORY_NSString_$_ReplaceSubString in libSDLmain.a(SDLMain.o) __objc_classrefs__DATA@0 in libSDLmain.a(SDLMain.o) "_OBJC_CLASS_$_NSObject", referenced from: _OBJC_CLASS_$_SDLMain in libSDLmain.a(SDLMain.o) "_CFBundleGetInfoDictionary", referenced from: _main in libSDLmain.a(SDLMain.o) "_CFRelease", referenced from: -[SDLMain setupWorkingDirectory:] in libSDLmain.a(SDLMain.o) -[SDLMain setupWorkingDirectory:] in libSDLmain.a(SDLMain.o) "__objc_empty_vtable", referenced from: _OBJC_METACLASS_$_SDLMain in libSDLmain.a(SDLMain.o) _OBJC_CLASS_$_SDLMain in libSDLmain.a(SDLMain.o) "_OBJC_CLASS_$_NSMenuItem", referenced from: __objc_classrefs__DATA@0 in libSDLmain.a(SDLMain.o) "_objc_msgSend", referenced from: -[SDLMain application:openFile:] in libSDLmain.a(SDLMain.o) -[SDLMain applicationDidFinishLaunching:] in libSDLmain.a(SDLMain.o) -[NSString(ReplaceSubString) stringByReplacingRange:with:] in libSDLmain.a(SDLMain.o) -[NSString(ReplaceSubString) stringByReplacingRange:with:] in libSDLmain.a(SDLMain.o) -[NSString(ReplaceSubString) stringByReplacingRange:with:] in libSDLmain.a(SDLMain.o) -[NSString(ReplaceSubString) stringByReplacingRange:with:] in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) _main in libSDLmain.a(SDLMain.o) "_OBJC_METACLASS_$_NSObject", referenced from: _OBJC_METACLASS_$_SDLMain in libSDLmain.a(SDLMain.o) _OBJC_METACLASS_$_SDLMain in libSDLmain.a(SDLMain.o) "_objc_msgSend_fixup", referenced from: l_objc_msgSend_fixup_objectForKey_ in libSDLmain.a(SDLMain.o) l_objc_msgSend_fixup_length in libSDLmain.a(SDLMain.o) l_objc_msgSend_fixup_alloc in libSDLmain.a(SDLMain.o) l_objc_msgSend_fixup_release in libSDLmain.a(SDLMain.o) ld: symbol(s) not found collect2: ld returned 1 exit status make[2]: *** [dist/Debug/GNU-MacOSX/opengl2] Error 1 make[1]: *** [.build-conf] Error 2 make: *** [.build-impl] Error 2 BUILD FAILED (exit value 2, total time: 263ms) any ideas? thanks a lot!

Read the article

Developer IT

decrease - Page 23 - Developer IT

Search Results

Search found 559 results on 23 pages for 'decrease'.

Page 23/23 | < Previous Page | 19 20 21 22 23

TCP packets larger than 4 KB don't get a reply from Linux

- by pts

Read the article

I need advices: small memory footprint linux mail server with spam filtering

- by petermolnar

Read the article

Picker view wont rotate- iPhone

- by lotuseater

Read the article

Solving embarassingly parallel problems using Python multiprocessing

- by gotgenes

Read the article

Different behavior of functors (copies, assignments) in VS2010 (compared with VS2005)

- by Patrick

Read the article

FreeBSD performance tuning. Sysctls, loader.conf, kernel

- by SaveTheRbtz

Read the article

video and file caching with squid lusca?

- by moon

Read the article

What's New in ASP.NET 4

- by Navaneeth

Read the article

mac, netbeans 6.8, c++, sdl, opengl: compilation problems

- by ufk

Read the article

< Previous Page | 19 20 21 22 23