Search Results

Search found 1875 results on 75 pages for 'jim thomas'.

Page 23/75 | < Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >

  • Bridge virtual machines out WLAN interface

    - by Thomas
    It seems that my wlan card (intel 5100 AGN) firmware doesn't allow "spoofing" MAC addresses. This has the side effect of destroying the capability to bridge out my virtual machines on that interface. Apparently this is a common thing on wlan cards. I can see the incoming traffic just fine in my virtual machines, but their DHCP queries don't get bridged out of the WLAN card. It works perfectly well when using the wired ethernet port. Is there a workaround for this? MAC-NAT or something? I don't want to route my virtual machines out to the Internet because I don't want my host OS to even have an IP address. I'm using Linux and KVM for virtualization.

    Read the article

  • Minimum permissions needed to create a user Home Folder in Windows Active Directory

    - by Jim
    We would like the Help Desk to have the responsibility of creating User Home folders instead of our 2nd level support. The help desk global group is already an Account Operator, so in Active Directory they are able to edit all User Attributes just fine. The problem is figuring out the minimum level of permissions needed on the File Server to create the home share, with out giving them access to everyone home share. So if they open AD Users and Computer, open the properties for a user, and enter \home\users\%username% in the profile tab and then click OK, they get the following error. The \home\users\username home folder was not created because you do not have create access on the server. The user account has been updated with the new home folder value but you must create the directory manually after obtaining the required access right. Right now I have given the Helpdesk group Full Control on the root folder only (no files or subdirectories) The directory is actually created, but the permissions on the newly created folder only show administrators full control, and no permissions for the configured user account. It sure sounds like I'd have to make the helpdesk local admins on the file servers, which is what I'd like to avoid. Especially since the file servers are a large cluster hosting much much more than the entire orgs home share structure.

    Read the article

  • How can I quickly change display settings (dual monitor setup / single monitor setup on laptop)?

    - by Daren Thomas
    I have my laptop (running Windows XP SP3) at work hooked up to an external monitor. Whenever I unplug the external monitor (time to go home!) I have to manually change the display settings. This takes time and involves a lot of clicks. Is there a way to automate changing these settings? I'm thinking of a hotkey solution or a little application that I can start with Launchy to toggle between two profiles. I use the MultiMon tool for "extending" the taskbar to the second monitor - will I have to give that up?

    Read the article

  • Program for remove exact duplicate files while caching search results

    - by John Thomas
    We need a Windows 7 program to remove/check the duplicates but our situation is somewhat different than the standard one for which there are enough programs. We have a fairly large static archive (collection) of photos spread on several disks. Let's call them Disk A..M. We have also some disks (let's call them Disk 1..9) which contain some duplicates which are to be found on disks A..M. We want to add to our collection new disks (N, O, P... aso.) which will contain the photos from disks 1..9 but, of course, we don't want to have any photos two (or more) times. Of course, theoretically, the task can be solved with a regular file duplicate remover but the time needed will be very big. Ideally, AFAIS now, the real solution would be a program which will scan the disks A..M, store the file sizes/hashes of the photos in an indexed database/file(s) and will check the new disks (1..9) against this database. However I have hard time to find such a program (if exists). Other things to note: we consider that the Disks A..M (the collection) doesn't have any duplicates on them the file names might be changed we aren't interested in approximated (fuzzy) comparison which can be found in some photo comparing programs. We hunt for exact duplicate files. we aren't afraid of command line. :-) we need to work on Win7/XP we prefer (of course) to be freeware TIA for any suggestions, John Th.

    Read the article

  • php jpeg support

    - by Thomas
    Hi all, I have complied php with the below options './configure' '--with-config-file-path=/opt/apache/php/etc' '--with-config-file-scan-dir=/opt/apache/php/etc/php.d' '--enable-sysvsem' '--enable-sysvshm' '--enable-sysvmsg' '--enable-shmop' '--enable-soap' '--enable-bcmath' '--disable-debug' '--enable-ftp' '--with-curl=/usr/include' '--with-regex=system' '--enable-inline-optimization' '--enable-magic-quotes' '--enable-mbstring' '--enable-wddx=shared' '--enable-xml' '--with-gd' '--with-gettext' '--with-mysql' '--with-zlib-dir=/usr/local/lib' '--enable-mbstring' '--prefix=/opt/apache/php' '--with-apxs2=/opt/apache/bin/apxs' '--with-zlib' '--with-openssl' '--with-freetype-dir=/usr/include/freetype2/freetype--with-jpeg-dir=/usr/lib/' but I have no jpeg support. Am I missing something? libjpeg and libjpeg-devel are installed Thanks

    Read the article

  • Can I grant permissions on files in windows 7 using a security identifier from another machine

    - by Thomas
    I have an external hard drive, and I wish to grant permissions on some files to users from 2 different computers without having to hook it up to the 2 different computers. I know the SID of the user on the other computer, I'd like to know if and how I can grant permissions to files using the SID. I'm running Windows 7 Professional 64 bits, and "The Other" computer Win 7 Home Premium 64 bits, they are not in a domain, but separate computers on a home network (not even same homegroup). Note: Duplicated question with: Is there a way to give NTFS file permissions to users from other Windows installations?

    Read the article

  • What is the harm in giving developers read access to application server application event logs?

    - by Jim Anderson
    I am a developer working on an ASP.NET application. The application writes logging messages to the Windows event log - a custom application log just for this application. However, I do not have any access to testing or staging web/application servers. I thought an admin could just give me read access to this event log to help in debugging problems (currently a service that is working in dev is not working in test environment and I have no idea why) but that is against my client's (I'm a consultant) policy. I feel silly to keep asking an admin to look at the event log for me. What is the harm in giving developers read access to application server application event logs? Is there a different method of application logging that sysadmins prefer programmers use? Surely, admins don't want to be fetching logging messages for developers all the time.

    Read the article

  • How to enable caching on Apache / Ubuntu Linux?

    - by Jim Mischel
    I have a large (several megabytes) XML file that's updated rather frequently (every 10 minutes or less) and gets a lot of traffic. I'd like to implement some caching to reduce bandwidth and server load. Looking at the Apache documents, I see a dizzying array of configuration options that involve various combinations of mod_expires, mod_headers, and mod_cache (and variants). I end up running in circles and the results aren't what I expect. I'm comfortable editing the various configuration files if I have some idea what I'm supposed to change. But at the moment I'm poking around in the dark and that's never a comfortable feeling. So, perhaps if I describe what I want, somebody here can take me by the hand and say, "This is what you need to do." Periodically, this file, call it "stuff.xml" is updated and a new version copied to the directory. The external url would be, for example, http://example.com/stuff.xml. Understand, this part works. Whenever I request the file, I get the expected result. But the file is big and I want to save bandwidth, so first I'd like to implement conditional GET semantics with the If-Modified-Since header. How do I do this? I've enabled mod_headers and mod_expired and added the <FilesMatching> section in my httpd.conf as recommended in countless examples I've seen online, but that didn't change the behavior when made a conditional GET request. I always get a status 200 with the entire document. So how the heck do I implement this? That'll cut down on neeless transfers. I'd also like to limit the amount of data transferred. Seeing as this is XML, gzipping it should save me 50% or more. My next step would be to somehow gzip the file and, if it's not too difficult, store it in memory. That'll cut down on per-access data transfer, and also reduce disk transfers. So how do I implement this type of caching? Thanks in advance.

    Read the article

  • Which will give more free RAM to linux?

    - by Linda Thomas
    Trying to avoid some issues so I've been trying to learn vm. in kernel tuning but still a little confused even after googling. The lower background_ratio is the sooner the flushes? the lower dirty_ratio is the less dirty ram that is kept, right vm.dirty_ratio = 20 vm.dirty_background_ratio = 1 or vm.dirty_ratio = 60 vm.dirty_background_ratio = 20 or vm.dirty_ratio = 20 vm.dirty_background_ratio = 10 or vm.dirty_ratio = 20 vm.dirty_background_ratio = 5

    Read the article

  • Script or Batch File to Automate Logon from Welcome Screen

    - by Guy Thomas
    Is there a script or batch file to automate the log-on process from the XP Welcome screen? As all details are the same Username, Password, and Domain in a room of 30 machines. The reason I don't use Windows AutoAdminLogon is I only want to logon temporary at different times as a user to run such things as online test for a class of high school students without the students logging on individually first, also it would be useful for admin tasks if I can change/specify the user details.

    Read the article

  • SQL 2005 Log Shipping - Was working, now isnt!

    - by Jim
    Hello, I had log shipping working between two SQL 2005 server fine. I suspect that a job was added to the source server which backed up the transaction log to disk (nothing to do with the existing log shipping job). As I understand it, if you do this then log shipping will fail to work. Sure enough, it no longer works. I've deleted the job which had just been created. Log shipping still does not work. I've rebooted both servers and, again, Log shipping does not work. I'm at a loss now... all I get is the folloing error: The log shipping secondary database XXXXXXXXXX has restore threshold of 45 minutes and is out of sync. No restore was performed for 5882 minutes. Restored latency is 15 minutes. Check agent log and logshipping monitor information. Any help appreciated! Thanks in advance.

    Read the article

  • How to restore windows.old for windows 7

    - by Jim Thio
    I reinstall windows. Then I regret that and want to go back. Fortunately the old windows is stored at windows.old I follow the instruction in http://support.microsoft.com/kb/971760 I did it all with small catches When I insert the windows 7 installer, the drive for installer is X and my hard disk is D rather than C. However, on normal windows operation the drive is C. Only when I boot through CD the partition is assigned to the letter D. There is no file bootsect on my windows installer So I can't do **D:\boot\bootsect /nt60 c:** Which should be changed to X:\boot\bootsect /nt60 C: or X:\boot\bootsect /nt60 D: depending on what it really does. As I said if I boot through windows dvd my hard disk letter is D but normally it's C. I am not even sure what that bootsect does anyway. I also can't do this one Attrib –h –s –r boot.ini.saved Copy boot.ini.saved boot.ini There is no file boot.ini or boot.ini.saved It's hidden but I don't see it if I try to look unhidden files either. Because I simply switch from windows 7 to windows 7 and the directory for windows don't change c:\windows I thought it should still work. Well, it doesn't. When windows restart it only goes to the logo and then restart the computer.

    Read the article

  • Remote Desktop Connection can't connect to Windows Server 2012

    - by Guy Thomas
    Mission to Remote Desktop INTO Windows Server 2012 (standalone). Situation: Control Panel, System, Remote Settings, Remote Desktop – Allow All firewalls off Connect attempt using a known IP address (ping works ok) Connect Option as a user who has already logged on. Error message: Remote Access Cannot Connect 1) Remote access not enabled 2) Remote computer turned off 3) Remote computer not available Additional info: The Server 2012 can RDC OUT. The machines I use to connect IN are Windows 7 and Windows 8, they will RDC to other machines. I have fair experience of configuring remote desktop. Question: Is this a fault of beta software on the 2012 server, or is there a new way of getting RDC to work that I am missing?

    Read the article

  • IE and Google Chrome timeout on an IIS6 hosted SSL page that Firefox handles well

    - by Thomas
    Ok, here's the scenario: Up until a few weeks ago, none of us noticed anything wrong with the corporate website. People were using it without complaint. Then, a client complained that a specific page on the site was timing out for him, and only when he committed a POST action on a form filled with data. I checked it out, and it timed out for me, too. But, it only timed out in Google Chrome and IE, not in Firefox. Additionally, the same page, on the same server, but served from a different domain name (one not under the protection of SSL, either) does not time out under any browser. To clarify: https://www.mysite.com/changes.php times out on POST, but the same with http works fine. That distinction (SSL vs. Non-SSL) seems to be important, as nothing else has changed. Our certificate is valid, and Firefox detects no errors thrown by the page. I've looked at the Request and Response headers from the page, and they all follow the correct formats. Then, after wandering through the site, I noticed a few other things. Both IE and Chrome will frequently time out on any page that is PHP-based. They never time out on static images or html files. I've looked at the site from a variety of different servers, my home and work workstations, and my netbook. Because of that, I've discounted a viral infection, as I highly doubt a virus is going to hit every one of the machines to which I have access in exactly the same manner. My setup is: Server: Win2k3, II6, PHP 5.2.9-1. Clients: IE7, IE8, Chrome (regular and dev channel): Frequent timeouts on PHP pages. Firefox 2, Firefox 3: No timeouts. Firebug shows no errors or even lengthy periods serving the pages. I've spent 2 days searching for any tech knowledge that I can find, and my search parameters are all too general. Everyone has problems loading SSL pages in IE and Chrome for a wide variety of reasons. The infrequent nature of the timeouts and the fact that there are no errors being reported anywhere is starting to drive me insane. Does anyone have any insight on a problem like this?

    Read the article

  • Plesk on Windows Server 2008 memory usage

    - by Thomas
    I have a server running IIS and Plesk. There is a problem every day now in which the memory usage of PleskControlPanel.exe and w3wp.exe slowly increases. And at some point all of the sites hosted on the server go down. Restarting Plesk through its panel will reset its memory usage for a while, and restarting IIS will make it last even longer, but there is still the constant memory climbing problem. I cannot see anything by looking through the event viewer. Has anyone ever seen anything like this with Plesk on Windows? Thanks for any help.

    Read the article

  • Shopping for Fast USB Flash Drives

    - by Jim McKeeth
    I would like to pick up some really fast USB flash drives in the 16 - 64 GB range. When looking at drives they just list their size, their form factor (key chain hook, slider, etc.) and the fact that they are all Hi-Speed USB 2.0. It seems like I have heard that different drives have different performance and life expectancy. The sales guy tells me that they are all the same performance any more, but it wouldn't be the first time a sales guy had the wrong technical details. Our objective is to run Virtual PC images off of them, so good speed and resilience to rewrites it important.

    Read the article

  • Automatic Excel Script

    - by Thomas
    I am a 6th year medical student and I'm working on my thesis. I have no experience with programming whatsoever, a friend recommended me to post my question here. I am strugling with the following problem: I have data of 400 patients, stored in 400 different excel files. Each file contains 34 columns in a specific order, let's say A to Z. The order is the same in each of these 400 files. Now I need to a make a new excel document that contains the first column of each patient. So I need all the first columns of my 400 different excel files, lined up next to each other in a new document. Preferebally in the form of a automatic script. After that I want to do the exact same thing but for the second column, then the third and so on. This is probably a problem that has already been solved. Otherwise could someone help me out? You have my thanks!

    Read the article

  • Win8 Change A Password

    - by Thomas
    I have a non-domain machine that I use with our company's domain resources regularly. I upgraded to Windows 8, and the "Change a password" option went away from the Ctrl-Alt-Del window. Can't seem to google anything about this subject, or find a way to access that password change dialog. I tried running the .reg file from http://www.sevenforums.com/tutorials/63014-ctrl-alt-del-screen-add-remove-change-password.html with no luck. I also tried to Disable "Remove Change Password" via gpedit.msc. I could do it from my domain laptop, but I like to do it on this machine because it updates all my saved copies of those credentials. My local account is tied to my hotmail account if that matters.

    Read the article

  • 13" MacBook Pro with Win 7 and External VGA gets 640x480

    - by Jim McKeeth
    I have a brand new 13" MacBook Pro - 2.26 GHz and the NVIDIA 9400M Video card. I installed Windows 7 (final) in boot camp and booted up to Windows 7. Installed all the drivers from the Apple disk and it was working great. Then I attached the external VGA adapter (from apple) to connect to a projector and it dropped down at 640x480 resolution. No matter what I did it wouldn't let me change to a higher resolution if the external VGA was connected. Once it disconnects then it goes back to the normal resolution. If I am booted into Snow Leopard it works fine. I tried updating the NVIDIA drivers and it behaved exactly the same. Ultimately I want to get 1024x768 or better resolution when connected to an external display. If it isn't fixable then I am curious if anyone else has seen this, if it is a known issue, and who to contact for support (Apple, Microsoft or NVIDIA?) Update: Just attaching the Mini-DVI to VGA adapter kicks it into 640x480, no projector is required. I tried forcing the display driver from Generic PnP Monitor to one that supported 1024x768 and that didn't work either.

    Read the article

  • How to make VLC show single FLAC file containing many tracks as separate tracks

    - by Bryce Thomas
    I have a single .flac file that encompasses multiple tracks comprising a music album along with the corresponding .cue file. I'm running Ubuntu 10.04 with VLC player, and am trying to get VLC player to show the individual tracks and allow me to use the previous and next controls to move back and forth between tracks. The problem I'm having is that when I open the single .flac file with VLC, it just shows a single track the duration of the entire album, and I'm unable to skip back and forth between tracks. Is there any way to have VLC show the individual tracks contained within a .flac file without having to pre-split the .flac file into individual track files first?

    Read the article

< Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >