Search Results

Search found 1031 results on 42 pages for 'subnet'.

Page 23/42 | < Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >

• Changing default gateway on workstations connected to Windows Domain SBS server

  - by Gary B2312321321

  We have xp workstations connected onto a small business server acting as active directory/isa firewall/proxy (no dhcp). Is there a reason that after installing a 2nd firewall on the network (same subnet etc), that changing the default gateway on the workstations isnt sufficient to route inet traffic through the new firewall? A freshly setup linux box connects straight on to the alternate firewall with just ip, default gateway. dns settings. Will having ISA still active on the network confuse the process? Are there further config settings deeper down in windows that need attention? Any ideas pointers on this would be appreciated? Other info: Firewalls tried: Smoothwall and Ipcop; small ethernet netwoork 40 pcs; can ping to new firwalls from workstations; activating web proxy on new firewall and reconfiguring workstation browser works fine; Point of 2nd firewall is lack of some necessary features on ISA for a linux app; Would be nice to have some redundancy to though

  Read the article

• Windows Media Center says "Searching for tuners" when I try to play live TV

  - by Louis

  After upgrading from Windows 8 Pro with Media Center to the 8.1 preview, I need some help in being able to watch live TV again. When I try to now, it says Please Wait. Searching for tuners. I tried reinstalling the software for the Hauppauge WinTV DCR-2650 TV tuner, and upgrading the firmware for both the tuner and the Cisco STA-1520 tuning adapter. I also tried swapping around the USB ports, cold-booting the devices, and running the Set Up TV Signal setting in WMC, but that says The TV signal cannot be configured because a TV tuner was not detected. Both devices look fine in Device Manager, reporting the "This device is working properly" status. I'm not sure if this is related, but I did have some network connectivity issues immediately after upgrading to Windows 8.1 where my either my subnet mask or default gateway was missing, and since the TV tuner shows up as a network device, I wonder if that might be related. However, I really don't know how those settings should look and Hyper-V sort of further complicates things with the virtual Ethernet adapters:

  Read the article

• Poor home office network performance and cannot figure out where the issue is

  - by Jeff Willener

  This is the most bizarre issue. I have worked with small to mid size networks for quite a long time and can say I'm comfortable connecting hardware. Where you will start to lose me is with managed switches and firewalls. To start, let me describe my network (sigh, shouldn't but I MUST solve this). 1) Comcast Cable Internet 2) Motorola SURFboard eXtreme Cable Modem. a) Model: SB6120 b) DOCSIS 3.0 and 2.0 support c) IPv4 and IPv6 support 3-A) Cisco Small Business RV220W Wireless N Firewall a) Latest firmware b) Model: RV220W-A-K9-NA c) WAN Port to Modem (2) d) vlan 1: work e) vlan 2: everything else. 3-B) D-Link DIR-615 Draft 802.11 N Wireless Router a) Latest firmware b) WAN Port to Modem (2) 4) Servers connected directly to firewall a) If firewall 3-A, then vlan 1 b) CAT5e patch cables c) Dell PowerEdge 1400SC w/ 10/100 integrated NIC (Domain Controller, DNS, former DHCP) d) Dell PowerEdge 400SC w/ 10/100/1000 integrated NIC (VMWare Server) 4) Linksys EZXS88W unmanaged Workgroup 10/100 Switch a) If firewall 3-A, then vlan 2 b) 25' CAT5e patch cable to firewall (3-A or 3-B) c) Connects xBox 360, Blu-Ray player, PC at TV 5) Office equipment connected directly to firewall a) If firewall 3-A, then vlan 1 b) ~80' CAT6 or CAT5e patch cable to firewall (3-A or 3-B) c) Connects 1) Dell Latitude laptop 10/100/1000 2) Dell Inspiron laptop 10/100 3) Dell Workstation 10/100/1000 (Pristine host, VMWare Workstation 7.x with many bridged VM's) 4) Brother Laser Printer 10/100 5) Epson All-In-One Workforce 310 10/100 5-A) NetGear FS116 unmanaged 10/100 switch a) I've had this switch for a long time and never had issues. 5-B) NetGear GS108 unmanaged 10/100/1000 switch a) Bought new for this issue and returned. 5-C) Linksys SE2500 unmanaged 10/100/1000 switch a) Bought new for this issue and returned. 5-D) TP-Link TL-SG10008D unmanaged 10/100/1000 a) Bought new for this issue and still have. 6) VLan 1 Wireless Connections (on same subnet if 3-B) a) Any of those at 5c b) HP Laptop 7) VLan 2 Wireless Connection (on same subnet if 3-B) a) IPad, IPod b) Compaq Laptop c) Epson Wireless Printer Shew, without hosting a diagram I hope that paints a good picture. The Issue The breakdown here is at item 5. No matter what I do I cannot have a switch at 5 and have to run everything wireless regardless of router. Issues related to using a switch (point 5 above) SpeedTest is good. Poor throughput to other devices if can communicate at all. Usually cannot ping other devices even on the same switch although, when able, ping times are good. Eventual lose of connectivity and can "sometimes" be restored by unplugging everything for several days, not minutes or hours but we're talking a week if at all. Directly connect to computer gives good internet connection however throughput to other devices connected to firewall is at best horrible. Yet printing doesn't seem to be an issue as long as they are connected via wireless. I have to force the RV220W to 1000Mb on the respective port if using a Gig Switch Issues related to using wireless in place of a switch (point 5 above) Poor throughput to other devices if can communicate. SpeedTest is good. Bottom line Internet speeds are awesome. By the way, Comcast went WAY above and beyond to make sure it was not them. They rewired EVERYTHING which did solve internet drops. Computer to computer connections are garbage Cannot get switch at 5 to work, yet other at 4 has never had an issue. Direct connection, bypass switch, is good for DHCP and internet. DNS must be on server, not firewall. Cisco insists its my switches but as you can see I have used four and two different cables with the same result. My gut feeling is something is happening with routing. But I'm not smart enough to know that answer. I run a lot of VM's at 5-c-3, could that cause it? What's different compared to my previous house is I have introduced Gigabit hardware (firewall/switches/computers). Some of my computers might have IPv6 turned on if I haven't turned it off already. I'm truly at a loss and hope anyone has some crazy idea how to solve this. Bottom line, I need a switch in my office behind the firewall. I've changed everything. The real crux is I will find a working solution and, again, after days it will stop working. So this means I cannot isolate if its a computer since I have to use them. Oh and a solution is not throwing more money at this. I'm well into $1k already. Yah, lame.

  Read the article

• Forcing DFS replication on Windows 2003 Web Edition SP2

  - by Greg B

  I have a pair of web servers running Windows Server 2003 Web Edition SP2 (build 3790). There servers are a on a Gigabit LAN and are on the same subnet. I created a new link on the 1st server and added the second box as a target to the link. I configured replication as ring. The 2nd server gets some of the files on the scheduled replication but this varies wildly which makes me think it's not running fully. The folder on server 1 is 1.3GB. Is there some way I can force repication (from a console?) and monitor the progress and see if/when/why it fails.

  Read the article

• How to troubleshoot a remote wmi query/access failure?

  - by Roman

  Hi I'm using Powershell to query a remote computer in a domain for a wmi object, eg: "gwmi -computer test -class win32_bios". I get this error message: Value does not fall within the expected range Executing the query local under the same user works fine. It seems to happen on both windows 2003 and also 2008 systems. The user that runs the shell has admin rights on the local and remote server. I checked wmi and dcom permissions as far as I know how to do this, they seem to be the same on a server where it works, and another where it does not. I think it is not a network issue, all ports are open that are needed, and it also happens within the same subnet. When sniffing the traffic we see the following errors: RPC: c/o Alter Cont Resp: Call=0x2 Assoc Grp=0x4E4E Xmit=0x16D0 Recv=0x16D0 Warning: GssAPIMechanism is not found, either caused by not reassembled, conversation off or filtering. And an errormessage from Kerberos: Kerberos: KRB_ERROR - KDC_ERR_BADOPTION (13) The option code in the packet is 0x40830000 Any idea what I should look into?

  Read the article

• Sonicwall networking

  - by Syed

  My Sonicwall LAN subnet is 192.168.1.0/24 X0: LAN IP 192.168.1.253 I also have intranet router 192.168.1.108 routing to 192.168.2.0/24 network. Internet is through WAN (X1) is all working fine. My LAN PC's can connect to intranet 192.168.2.0/24 via static route from LANsubnet to 192.168.2.0/24 as 192.168.1.108 as gateway. Now I have LAN2 10.2.1.254 (10.2.1.0/24)on X4 port. I can access Internet from LAN2, now I want to allow intranet from LAN2. What static routes do I need to make this work?

  Read the article

• Watchguard firebox: public IP addresses behind firewall with as much usable IP addresses as possible

  - by martinezpt

  Our ISP assigned us 16 public IP addresses that we want to assign to hosts behind a Watchguard firebox x750e. The IP addresses are: x.x.x.176/28 of which x.x.x.177 is the gateway. The hosts will be running software that needs to be directly assigned the public IP address so 1:1 NAT is not an option. I found this document that gives examples on how to assign public IP addresses to hosts behind the firewall, using an optional interface: http://www.watchguard.com/help/configuration-examples/public_IP_behind_XTM_configuration_example_(en-US).pdf However, I can't implement scenario 1 as it won't allow me to use the same subnet on both interfaces. As for scenario 2, splitting the address range into 2 subnets will decrease the usable hosts on the optional interface to 5 (8 - network - broadcast - optional interface ip). I'm convinced that there must be a better way to address this problem and maximize the number of usable IP addresses but I'm not very familiar with this specific firewall. Are there any suggestions on how to keep the hosts behind the firewall with public IP addresses while maximizing the usable IP addresses? thanks

  Read the article

• Connectivity good between VMs, but no connectivity between host and VM

  - by Greg Sansom

  I have a strange situation where connectivity (ie ping, access shared folders and services) is fine between virtual machines, but not between the host and the virtuals. I've been using Hyper-V almost every day for years and have never had a problem like this. Note the following: The host machine and all virtuals are running Windows Server 2008 r1. All machines can connect to the web, and the gateway router. Subnet mask and gateway reported in ipconfig are identical for all machines. I can access virtuals via the Hyper-V snap-in only. Doea anyone have suggestions about what might be wrong, or what diagnostic steps I can take?

  Read the article

• AWS VPN Tunnel going down without traffic

  - by Asfura

  I managed to setup a site-to-site VPN connection from Amazon VPC to a company's network, and after a lot of configuration it was working fine, but now i realized that the VPN tunnel is DOWN every time there's no traffic going trough for a couple minutes. The only way that i have found to generate traffic is to reach the amazon instance from the company's network and then the tunnel goes up again. I had a cronjob doing ping every minute, but i think it should have a keepalive option somewhere, or at least a log file of the tunnels to find out what's going on. Any ideas to keep the tunnel up and/or bring it up from amazon? The firewall is a Checkpoint R75.20, it only allows one tunnel at a time for the same subnet, so i cant have both tunnels active. Thank you, any questions just ask. EDIT I forgot to add, the ping keepalive was working great (maybe generating a bit of traffic, but nothing to worry about), the connection dropped because i had to restart the instance, and it that little time it dropped me.

  Read the article

• VM can’t connect to outside in bridged mode

  - by Kamal

  Hi Guys, I am not able to ping any machine(not even the host) from Guest VM in bridged mode. But I got an IP which is on the same subnet as host. I can ping my guest VM from the host and can use ssh to connect to the guest. I am using Vmware workstation 6.5. Guest VM is a centos VM and host is windows xp. Every thing works fine in NAT mode. Any clues as to what could be happening. I tried disabling all the firewalls I have. My virtual network editor shows that my ethernet adapter(the one my host uses) is used for bridging. It is connected. I don't understand how I can get an IP address from DHCP server. I can't ping any of the DNS servers in generated /etc/resolv.conf which are the same as that of my host

  Read the article

• Is this a common/bug on this PPPoE setting for Cisco ASA 5505?

  - by DCAlliances

  We have to change the way the firewall setup due to we've changed the internet provider. The way we setup we have ADSL modem and we have to do a full bridge mode and the firewall configuration has to change from Static IP to Use PPPoE option on Outside interface with PPPoE username and password, CHAP authentication, WAN IP and WAN subnet mask. [See the attachment] It's been working ok with the use of PPPoE option however the issue is that if we un-plug the power cable of the firewall. This "Outside" interface turned to blank - NO WAN IP, PPPoE username and password. So basically, we have to retype this information again. Is this common or a bug? Any ideas? Thanks

  Read the article

• How to SSH to guest ubuntu OS in vmplayer4

  - by Grace

  I have installed vmplayer4.0.4 on Windows7, and install ubuntu12.04 as Guest OS. Basically i have two problems: Default vmplayer use NAT for network access. I could ping the guest OS from the Host OS. But how could i access the Guest OS from outside the Host OS? If i change to Bridged Mode, sure the Guest Ubuntu OS could get DHCP ip in the same subnet as Host OS. But i could not ping the Guest OS from the Host OS, or vice versa, even if i disable the iptables firewall on Ubuntu Guest OS like following: iptables -F iptables -X iptables -t nat -F iptables -t nat -X iptables -t mangle -F iptables -t mangle -X iptables -P INPUT ACCEPT iptables -P FORWARD ACCEPT iptables -P OUTPUT ACCEPT I could not figure it out, could anyone help on this issue? Thanks in advance.

  Read the article

• DrayTek Vigor 2920(n): VPN with VLAN restrictions?

  - by Dirk

  Hi, I'm currently installing a DrayTek Vigor 2920n router in a new office. This router is to be used for 2 seperate companies. For one of these companies, the router has a LAN-2-LAN (VPN) connection to a datacenter configured. The other company should not be able to access this other (VPN-)network. I'm aware of the capability of this router to have VLAN's, but I cannot figure out how to configure the VPN-connection to only be accessible for VLAN0 and not for VLAN1. I know I can also add another router to physically split both networks, but we bought the DrayTek with the idea that it could easily have the VPN-connection available for VLAN0 and not for VLAN1. VLAN1 can easily be in another subnet, that's fine, although, I don't know how to configure that on this DrayTek. Can anyone point me in the right direction? Thanks in advance, Dirk

  Read the article

• Accessing IPv6 router interface from a minimal Fedora installation?

  - by Zack

  I've recently installed Fedora 16 and am trying to set up a simple apache server. The only problem I've run into so far is that I'm unable to access my router's web interface from any box on my network. It assigns addresses via dhcp, and the router always responds to a ping. The server is also picking up an IP from the router on the proper subnet. Now, all I really need to do is forward a port, however I am receiving "Unable to connect" through the web interfaces and "connection refused" via telnet. What are my options, and how might I go about troubleshooting this? Will I need the server's ip to be static in order to change these settings? The router is a "Netopia" model, if that helps.

  Read the article

• setup Mac Book Wifi interface as Wifi hotspot using specific DHCP option

  - by srjohnhuang

  I want to using my Mac Book as an access point. Besides that I also need to configure its DHCP server to not provide DNS info. For example, Mac Books AP's ssid is "MacBookHotspot". While my iPhone connected to "MacBookHotspot", I want the Wifi info displayed my iPhone would be looked like: IP ADDRESS DHCP(tab) IP Address 192.168.0.1 Subnet Mask 255.255.255.0 Router 192.168.0.254 DNS Search Domains Client ID (key point: DNS filed is blank) Does anyone have any good suggestion? Thanks!

  Read the article

• dhcpd: varying vendor-class-identifier

  - by jessicah

  I'm having trouble selectively sending parameters in response to a DHCP Inform packet using groups (or even without, just using host declarations) for bootp stuff. My configuration file right now looks like: subnet 130.123.131.128 netmask 255.255.255.128 { allow unknown-clients; } host dev-mac-09 { option vendor-class-identifier "example-identifier"; hardware ethernet 10:9a:dd:51:ff:83; } If I put vendor-class-identifier in the global scope, using tcpdump I can see that the client receives the vendor class option successfully. If I take it out, and just keep it in the host scope (or group scope), the client never receives the option. Specifying option dhcp-parameter-request list 60 doesn't help either. I did try using a class definition inside a group, but then it applied even if the host wasn't a part of the group. As an aside, how do I get detailed logging? At least something to indicate what groups and things got used to generate the response to the client.

  Read the article

• Setting up a vpn and IIS IP address restrictions

  - by carpat

  I'm trying to get a VPN set up with internal access only sites. I have set up a VPN on a windows server (single VPS server), and I can connect from a remote computer and I get an IP assigned correctly (from 192.168.1.1 - 255) Next I configured IIS (running on the same machine) IP Address and Domain Restrictions to only allow only IP address range 192.168.1.0 with subnet mask 255.255.255.0 When I connect to the VPN with "Use Default Gateway on Remote Network" (so that requests must go through the vpn), I get a 403 from the internal sites. What did I miss?

  Read the article

• VM can't connect to outside in bridged mode

  - by Kamal

  I am not able to ping any machine(not even the host) from Guest VM in bridged mode. But I got an IP which is on the same subnet as host. I can ping my guest VM from the host and can use ssh to connect to the guest. I am using Vmware workstation 6.5. Guest VM is a centos VM and host is windows xp. Every thing works fine in NAT mode. Any clues as to what could be happening. I tried disabling all the firewalls I have.

  Read the article

• Multicast doesn't seem to be working on RHEL 5.5

  - by NullUser

  I'm trying to install Oracle Grid Infrastructure on two machines. Their documentation states You must enable multicasting for the cluster on the IP address subnet ranges 224.0.0.0/24 and 230.0.1.0/24 So I ran: route add -net 224.0.0.0/24 dev eth2 route add -net 230.0.1.0/24 dev eth2 route -n produces: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 230.0.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 224.0.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 # and others An ifconfig eth2 shows, among other things, UP BROADCAST RUNNING MULTICAST. However, when I run their multicast test utility, it fails me: Test for Multicast address 230.0.1.0 Sep 3 19:40:39 | Multicast Failed for eth2 using address 230.0.1.0:42000 Test for Multicast address 224.0.0.251 Sep 3 19:41:10 | Multicast Failed for eth2 using address 224.0.0.251:42001 What am I doing wrong?

  Read the article

• OSSEC agent behind NAT

  - by Eric

  I am working on an OSSEC deployment where I will have multiple agents behind 1 public IP. Below is an example of the setup Private Network OSSEC-Agent1 (192.168.1.10) OSSEC-Agent2 (192.168.50.33) OSSEC-Agent3 (10.10.10.1) Those IPs NAT to 1 public IP (1.1.1.1) Then 1.1.1.1 talks to the public OSSEC server on 2.2.2.2 I've read some OSSEC documentation talking about NAT here, but it doesn't tell me exactly what I need to know. Their example is using an entire /24 subnet and mine will mainly have multiple agents to only 1 public IP. With the setup so far, I brought Agent1 online fine and it is communicating to the OSSEC server. However Agent2 continues to fail trying to connect to 2.2.2.2. Even though when I added the key, I had the correct name for it, so I know it talked to the portal at least once for that information. I'm assuming it's just getting confused with the multiple keys to 1 public IP. I basically want to know if this is possible and/or if I'm just overlooking something simple. Any help would be greatly appreciated.

  Read the article

• Remote Desktop to Virtual Machine

  - by Valvaris

  Hello: I recently reformatted one of my servers with Windows Server 2008 x64 and with that, installed the latest version of VMWare server on it. Within that, I created a new Windows Server 2003 R2 x86 virtual machine for the purposes of being a backup domain controller. I was able to successfully configure it as a domain controller and have it provide DNS service to my domain. I've been using the VMWare remote console to set this up and figured it was time to get remote desktop working. I set it up as I have with many other computers on my network (hitting the checkbox, making the firewall isn't blocking it) and I cannot get remote desktop to connect to it. I've tried using the computer name and its IP address neither work. I can ping the computer from the outside but the Virtual machine cannot ping anything from inside it. All machines are on the same subnet. I can't seem to figure this out.

  Read the article

• Postfix configuration problem

  - by dhanya

  Can anyone help me by giving your postfix configuration file as a reference so that I can find my mistakes? I'm working on SUSE Linux Enterprise Server. My goal is to set up a mailserver in a campus network. Postfix shows it is running but no mail is sent to var/spool/mail I send mail using mail command at terminal. Here is my main.cf file, please help me finding a solution: readme_directory = /usr/share/doc/packages/postfix-doc/README_FILES inet_protocols = all biff = no mail_spool_directory = /var/mail canonical_maps = hash:/etc/postfix/canonical virtual_alias_maps = hash:/etc/postfix/virtual virtual_alias_domains = hash:/etc/postfix/virtual relocated_maps = hash:/etc/postfix/relocated transport_maps = hash:/etc/postfix/transport sender_canonical_maps = hash:/etc/postfix/sender_canonical masquerade_exceptions = root masquerade_classes = envelope_sender, header_sender, header_recipient myhostname = cmail.cetmail delay_warning_time = 1h message_strip_characters = \0 program_directory = /usr/lib/postfix inet_interfaces = all #inet_interfaces = 127.0.0.1 masquerade_domains = cetmail mydestination = cmail.cetmail, localhost.cetmail, cetmail defer_transports = mynetworks_style = subnet disable_dns_lookups = no relayhost = postfix mailbox_command = cyrus mailbox_transport = strict_8bitmime = no disable_mime_output_conversion = no smtpd_sender_restrictions = hash:/etc/postfix/access smtpd_client_restrictions = smtpd_helo_required = no smtpd_helo_restrictions = strict_rfc821_envelopes = no smtpd_recipient_restrictions = permit_mynetworks,reject_unauth_destination smtp_sasl_auth_enable = no smtpd_sasl_auth_enable = no smtpd_use_tls = no smtp_use_tls = no alias_maps = hash:/etc/aliases mailbox_size_limit = 0 message_size_limit = 10240000

  Read the article

• forward ssh ports on EC2

  - by Will Glass

  I have an SSH server on a private subnet within an EC2 vpc listening for ssh on port 9022 I also have a nat instance (standard Amazon EC2 nat) on a public instance. I would like to forward incoming SSH connections (port 9022) to my nat to the internal server (port 9022). I tried this, but it didn't work: sudo iptables -t nat -I PREROUTING -p tcp -i eth0 --dport 9022 -j DNAT --to-destination 10.0.2.11:9022 I verified that 10.0.2.11 is listening on port 9022. (I can telnet). I verified my security group allows incoming port 9022. I verified that /proc/sys/net/ipv4/ip_forward is 1. What am I missing? Edit: Turns out this was correct after all. I had a mistake in my security group.

  Read the article

• OSX 10.6 Cisco IPSEC strange behavior

  - by tair

  I'm trying to connect to Cisco IPSEC VPN of my company over DSL Internet. I managed to successfully connect using Cisco VPN Client, now I'm trying to switch to OSX 10.6 native client, because of licensing issues. The problems is that the connection fails with a dialog box containing the message: The negotiation with the VPN server failed. Verify the server address and try reconnecting. I checked logs: Jun 29 13:10:39 racoon[4551]: Connecting. Jun 29 13:10:39 racoon[4551]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1). Jun 29 13:10:39 racoon[4551]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2). Jun 29 13:10:39 racoon[4551]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2). Jun 29 13:10:39 racoon[4551]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode). Jun 29 13:10:39 racoon[4551]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3). Jun 29 13:10:42 racoon[4551]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:10:42 racoon[4551]: IKEv1 XAUTH: success. (XAUTH Status is OK). Jun 29 13:10:42 racoon[4551]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:10:42 racoon[4551]: IKEv1 Config: retransmited. (Mode-Config retransmit). Jun 29 13:10:42 racoon[4551]: IKE Packet: receive success. (MODE-Config). Jun 29 13:10:42 configd[19]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.1.107), current interface setting (name: u92.168.54.147, subnet: 255.255.255.0, destination: 192.168.54.147). Jun 29 13:10:42 configd[19]: network configuration changed. Jun 29 13:10:42 vmnet-bridge[111]: Dynamic store changed Jun 29 13:10:42 named[62]: not listening on any interfaces Jun 29 13:10:58: --- last message repeated 1 time --- Jun 29 13:10:58 configd[19]: SCNCController: Disconnecting. (Connection tried to negotiate for, 16 seconds). Jun 29 13:10:58 racoon[4551]: IKE Packet: transmit success. (Information message). Jun 29 13:10:58 racoon[4551]: IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA). Jun 29 13:10:58 racoon[4551]: Disconnecting. (Connection tried to negotiate for, 19.113382 seconds). Jun 29 13:10:58 named[62]: not listening on any interfaces Jun 29 13:10:58 vmnet-bridge[111]: Dynamic store changed Jun 29 13:10:58 named[62]: not listening on any interfaces Jun 29 13:10:58 configd[19]: network configuration changed. Then I opened Terminal, started pinging a server behind VPN, and tried to connect again. Now connection is OK! Logs this time: Jun 29 13:46:53 racoon[8136]: Connecting. Jun 29 13:46:53 racoon[8136]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1). Jun 29 13:46:53 racoon[8136]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2). Jun 29 13:46:53 racoon[8136]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2). Jun 29 13:46:53 racoon[8136]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode). Jun 29 13:46:53 racoon[8136]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:46:56 racoon[8136]: IKEv1 XAUTH: success. (XAUTH Status is OK). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:46:56 racoon[8136]: IKEv1 Config: retransmited. (Mode-Config retransmit). Jun 29 13:46:56 racoon[8136]: IKE Packet: receive success. (MODE-Config). Jun 29 13:46:56 configd[19]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.1.107), current interface settinaddress: 192.168.54.149, subnet: 255.255.255.0, destination: 192.168.54.149). Jun 29 13:46:56 vmnet-bridge[111]: Dynamic store changed Jun 29 13:46:56 named[62]: not listening on any interfaces Jun 29 13:46:56 configd[19]: network configuration changed. Jun 29 13:46:56 named[62]: not listening on any interfaces Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1). Jun 29 13:46:56 racoon[8136]: IKE Packet: receive success. (Initiator, Quick-Mode message 2). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3). Jun 29 13:46:56 racoon[8136]: IKEv1 Phase2 Initiator: success. (Initiator, Quick-Mode). Jun 29 13:46:56 racoon[8136]: Connected. Jun 29 13:46:56 configd[19]: SCNCController: Connected. I tested it several times and it consistently behaves the same. What is the magic?

  Read the article

• UDP packets to IP addresses other than specific ones not arriving and not shown in Wireshark

  - by Max

  I'm writing a service using UDP, but I can't manage to reply to the client. When sending to the client via the DHCP-assigned IP (192.168.1.143) Wireshark shows no sent packets. The server receives and Wireshark shows any packet sent by the client (broadcasted). If I send to a random, unassigned IP Wireshark doesn't show it. I thought the NIC would happily send it, since there is a router in the way - shouldn't Wireshark show it, even though it cannot possibly be received by a remote endpoint? If I send to either the router IP or another (specific, there is only one other) computer, the packet is shown in Wireshark. I am running Windows 7, the firewall is turned off using the control panel. Does the fact that wireshark doesn't show these packets mean that they aren't sent? What reason could there be for showing packets to one IP, but not another, on the same subnet?

  Read the article

< Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >