Search Results

Search found 4990 results on 200 pages for 'traffic measurement'.

Page 23/200 | < Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >

• Funnelling http traffic

  - by spencer p

  I have a situation where a large batch of servers (X), on demand, need to request data from a smaller set of web servers (Y). The worst case scenario is if all servers in X decide to fetch different requests to one server in Y. That would be X amount of connections, which could be a very large burst of traffic. The best case scenario is if 1 server in X hit 1 server in Y in tandem. Life does not work like this. One idea to entertain is placing a proxy, similar to squid between X and Y. All of X servers can connect to this proxy, but would result in a few persistent (http keepalive) connections to Y. If The few were say, 3 or 4, then it would funnel. If we could then rate limit those connections and traffic decides to spike unusually high, we wouldn't hurt anyone but ourselves. Thoughts?

  Read the article

• servers connected to a poweredge 6248 receive traffic for their 'neighbours'

  - by Hannes

  In the network we have a few vlans but at the moment I was investigating vlan2 which carries the most traffic. When tcpdumping on the eth0.2 interface, I see a lot of packets arriving which are not addressed to, nor coming from the server. I checked this on several servers in the network and they all have the same issues. In short, our switches don't switch the traffic but threat it like they are a hub. Can you tell me what settings on the dell poweredge 6248 should prevent this behaviour?

  Read the article

• How do I route traffic to website using a spcified network connection on Windows 7

  - by rwetzeler

  I want to route all traffic to a website over my wireless connection while the rest of the traffic using my lan. What I tried was first finding out the IP address of the website I want to go to. For example, lets say pandora.com. I found it resolves to 208.85.40.20. I have entered that entry into my hosts file. I then added that route using route add 208.85.40.20 mask 255.255.255.255 WirelessIP. It doesn't seem to work however. Instead of using the IP address, is there a way that I can just say.. this URL to route over that connection? Does anyone know of a program that I can install that will do this.. possibly some sort of proxy or a software load balancer that can do this?

  Read the article

• How to route local traffic over switch?

  - by Franz Kafka

  I'm just cabled up at home but haven't got any way of verifying that gigabit speed can be reached. As I've only got one laptop with one network card, one cable, and one switch, I'm kind of stuck. I'm using a tool that you can start as a server or as a client to send data from one box to another. I would like to send and receive on the same Windows box. I guess if I use my network local IP address, my Windows 8.1 PC will just route traffic internally. Is there some way of forcing the traffic to go to the switch and back again?

  Read the article

• Redirecting or routing all traffic to OpenVPN on a Mac OS X client

  - by sdr56p

  I have configured an OpenVPN (2.2.1) server on an Ubuntu virtual machine in the Amazon elastic compute cloud. The server is up and running. I have installed OpenVPN (2.2.1) on a Mac OS X (10.8.2) client and I am using the openvpn2 binary to connect (in opposition to other clients like Tunnelblick or Viscosity). I can connect with the client and successfully ping or ssh the server through the tunnel. However, I can't redirect all internet traffic through the VPN even if I use the push "redirect-gateway def1 bypass-dhcp" option in the server.conf configurations. When I connect to the server with these configurations, I get a successful connection, but then an infinite series of error messages: "write UDPv4: No route to host (code=65)". Traffic routing seems to be compromised because I am not able to access anything anymore, not even the OpenVPN server (by pinging 10.8.0.1 for instance). This is beyond me. I am finding little help on the web and don't know what to try next. I don't think it is a problem of forwarding the traffic on the server since, first, I have also took care of that and, second, I can't even ping the VPN server locally through the tunnel (or ping anything at all for that matter). Thank you for your help. Here is the server.conf. file: port 1194 proto udp dev tun ca ca.crt cert ec2-server.crt key ec2-server.key # This file should be kept secret dh dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "redirect-gateway def1 bypass-dhcp" client-to-client keepalive 10 120 comp-lzo persist-key persist-tun status openvpn-status.log verb 3 And the client.conf file: client dev tun proto udp remote servername.com 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert Toto5.crt key Toto5.key ns-cert-type server comp-lzo verb 3 Here is the connection log with the error messages: $ sudo openvpn2 --config client.conf Wed Mar 13 22:58:22 2013 OpenVPN 2.2.1 x86_64-apple-darwin12.2.0 [SSL] [LZO2] [eurephia] built on Mar 4 2013 Wed Mar 13 22:58:22 2013 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Wed Mar 13 22:58:22 2013 LZO compression initialized Wed Mar 13 22:58:22 2013 Control Channel MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ] Wed Mar 13 22:58:22 2013 Socket Buffers: R=[196724->65536] S=[9216->65536] Wed Mar 13 22:58:22 2013 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Wed Mar 13 22:58:22 2013 Local Options hash (VER=V4): '41690919' Wed Mar 13 22:58:22 2013 Expected Remote Options hash (VER=V4): '530fdded' Wed Mar 13 22:58:22 2013 UDPv4 link local: [undef] Wed Mar 13 22:58:22 2013 UDPv4 link remote: 54.234.43.171:1194 Wed Mar 13 22:58:22 2013 TLS: Initial packet from 54.234.43.171:1194, sid=ffbaf343 d0c1a266 Wed Mar 13 22:58:22 2013 VERIFY OK: depth=1, /C=US/ST=CA/L=SanFrancisco/O=Fort-Funst ... ost.domain Wed Mar 13 22:58:22 2013 VERIFY OK: nsCertType=SERVER Wed Mar 13 22:58:22 2013 VERIFY OK: depth=0, /C=US/ST=CA/L=SanFrancisco/O=Fort-Funst ... ost.domain Wed Mar 13 22:58:23 2013 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Mar 13 22:58:23 2013 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Mar 13 22:58:23 2013 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Mar 13 22:58:23 2013 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Mar 13 22:58:23 2013 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Wed Mar 13 22:58:23 2013 [ec2-server] Peer Connection Initiated with 54.234.43.171:1194 Wed Mar 13 22:58:25 2013 SENT CONTROL [ec2-server]: 'PUSH_REQUEST' (status=1) Wed Mar 13 22:58:25 2013 PUSH: Received control message: 'PUSH_REPLY,route 10.8.0.0 255.255.255.0,topology net30,ping 10,ping-restart 120,ifconfig 10.8.0.6 10.8.0.5' Wed Mar 13 22:58:25 2013 OPTIONS IMPORT: timers and/or timeouts modified Wed Mar 13 22:58:25 2013 OPTIONS IMPORT: --ifconfig/up options modified Wed Mar 13 22:58:25 2013 OPTIONS IMPORT: route options modified Wed Mar 13 22:58:25 2013 ROUTE default_gateway=0.0.0.0 Wed Mar 13 22:58:25 2013 TUN/TAP device /dev/tun0 opened Wed Mar 13 22:58:25 2013 /sbin/ifconfig tun0 delete ifconfig: ioctl (SIOCDIFADDR): Can't assign requested address Wed Mar 13 22:58:25 2013 NOTE: Tried to delete pre-existing tun/tap instance -- No Problem if failure Wed Mar 13 22:58:25 2013 /sbin/ifconfig tun0 10.8.0.6 10.8.0.5 mtu 1500 netmask 255.255.255.255 up Wed Mar 13 22:58:25 2013 /sbin/route add -net 10.8.0.0 10.8.0.5 255.255.255.0 add net 10.8.0.0: gateway 10.8.0.5 Wed Mar 13 22:58:25 2013 Initialization Sequence Completed ^CWed Mar 13 22:58:30 2013 event_wait : Interrupted system call (code=4) Wed Mar 13 22:58:30 2013 TCP/UDP: Closing socket Wed Mar 13 22:58:30 2013 /sbin/route delete -net 10.8.0.0 10.8.0.5 255.255.255.0 delete net 10.8.0.0: gateway 10.8.0.5 Wed Mar 13 22:58:30 2013 Closing TUN/TAP interface Wed Mar 13 22:58:30 2013 SIGINT[hard,] received, process exiting toto5:ttntec2 Dominic$ sudo openvpn2 --config client.conf --remote ec2-54-234-43-171.compute-1.amazonaws.com Wed Mar 13 22:58:57 2013 OpenVPN 2.2.1 x86_64-apple-darwin12.2.0 [SSL] [LZO2] [eurephia] built on Mar 4 2013 Wed Mar 13 22:58:57 2013 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Wed Mar 13 22:58:57 2013 LZO compression initialized Wed Mar 13 22:58:57 2013 Control Channel MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ] Wed Mar 13 22:58:57 2013 Socket Buffers: R=[196724->65536] S=[9216->65536] Wed Mar 13 22:58:57 2013 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Wed Mar 13 22:58:57 2013 Local Options hash (VER=V4): '41690919' Wed Mar 13 22:58:57 2013 Expected Remote Options hash (VER=V4): '530fdded' Wed Mar 13 22:58:57 2013 UDPv4 link local: [undef] Wed Mar 13 22:58:57 2013 UDPv4 link remote: 54.234.43.171:1194 Wed Mar 13 22:58:57 2013 TLS: Initial packet from 54.234.43.171:1194, sid=a0d75468 ec26de14 Wed Mar 13 22:58:58 2013 VERIFY OK: depth=1, /C=US/ST=CA/L=SanFrancisco/O=Fort-Funst ... ost.domain Wed Mar 13 22:58:58 2013 VERIFY OK: nsCertType=SERVER Wed Mar 13 22:58:58 2013 VERIFY OK: depth=0, /C=US/ST=CA/L=SanFrancisco/O=Fort-Funst ... ost.domain Wed Mar 13 22:58:58 2013 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Mar 13 22:58:58 2013 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Mar 13 22:58:58 2013 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Mar 13 22:58:58 2013 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Mar 13 22:58:58 2013 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Wed Mar 13 22:58:58 2013 [ec2-server] Peer Connection Initiated with 54.234.43.171:1194 Wed Mar 13 22:59:00 2013 SENT CONTROL [ec2-server]: 'PUSH_REQUEST' (status=1) Wed Mar 13 22:59:00 2013 PUSH: Received control message: 'PUSH_REPLY,redirect-gateway def1 bypass-dhcp,route 10.8.0.0 255.255.255.0,topology net30,ping 10,ping-restart 120,ifconfig 10.8.0.6 10.8.0.5' Wed Mar 13 22:59:00 2013 OPTIONS IMPORT: timers and/or timeouts modified Wed Mar 13 22:59:00 2013 OPTIONS IMPORT: --ifconfig/up options modified Wed Mar 13 22:59:00 2013 OPTIONS IMPORT: route options modified Wed Mar 13 22:59:00 2013 ROUTE default_gateway=0.0.0.0 Wed Mar 13 22:59:00 2013 TUN/TAP device /dev/tun0 opened Wed Mar 13 22:59:00 2013 /sbin/ifconfig tun0 delete ifconfig: ioctl (SIOCDIFADDR): Can't assign requested address Wed Mar 13 22:59:00 2013 NOTE: Tried to delete pre-existing tun/tap instance -- No Problem if failure Wed Mar 13 22:59:00 2013 /sbin/ifconfig tun0 10.8.0.6 10.8.0.5 mtu 1500 netmask 255.255.255.255 up Wed Mar 13 22:59:00 2013 /sbin/route add -net 54.234.43.171 0.0.0.0 255.255.255.255 add net 54.234.43.171: gateway 0.0.0.0 Wed Mar 13 22:59:00 2013 /sbin/route add -net 0.0.0.0 10.8.0.5 128.0.0.0 add net 0.0.0.0: gateway 10.8.0.5 Wed Mar 13 22:59:00 2013 /sbin/route add -net 128.0.0.0 10.8.0.5 128.0.0.0 add net 128.0.0.0: gateway 10.8.0.5 Wed Mar 13 22:59:00 2013 /sbin/route add -net 10.8.0.0 10.8.0.5 255.255.255.0 add net 10.8.0.0: gateway 10.8.0.5 Wed Mar 13 22:59:00 2013 Initialization Sequence Completed Wed Mar 13 22:59:00 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:00 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:01 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:01 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:01 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:02 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:02 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:02 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:02 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:02 2013 write UDPv4: No route to host (code=65) ... The routing table after a connection WITHOUT the push redirect-gateway (all traffic is not redirected to the VPN and everything is working fine, I can ping or ssh the OpenVPN server and access all other Internet resources through my default gateway): Destination Gateway Flags Refs Use Netif Expire default user148-1.wireless UGSc 50 0 en1 10.8/24 10.8.0.5 UGSc 2 7 tun0 10.8.0.5 10.8.0.6 UH 3 2 tun0 127 localhost UCS 0 0 lo0 localhost localhost UH 6 6692 lo0 client.openvpn.net client.openvpn.net UH 3 18 lo0 142.1.148/22 link#5 UCS 2 0 en1 user148-1.wireless 0:90:b:27:10:71 UHLWIir 50 0 en1 76 user150-173.wirele localhost UHS 0 0 lo0 142.1.151.255 ff:ff:ff:ff:ff:ff UHLWbI 0 2 en1 169.254 link#5 UCS 1 0 en1 169.254.255.255 0:90:b:27:10:71 UHLSWi 0 0 en1 71 The routing table after a connection with the push redirect-gateway option enable as in the server.conf file above (all internet traffic should be redirected to the VPN tunnel, but nothing is working, I can't access any Internet ressources at all): Destination Gateway Flags Refs Use Netif Expire 0/1 10.8.0.5 UGSc 1 0 tun0 default user148-1.wireless UGSc 7 0 en1 10.8/24 10.8.0.5 UGSc 0 0 tun0 10.8.0.5 10.8.0.6 UHr 6 0 tun0 54.234.43.171/32 0.0.0.0 UGSc 1 0 en1 127 localhost UCS 0 0 lo0 localhost localhost UH 3 6698 lo0 client.openvpn.net client.openvpn.net UH 0 27 lo0 128.0/1 10.8.0.5 UGSc 2 0 tun0 142.1.148/22 link#5 UCS 1 0 en1 user148-1.wireless 0:90:b:27:10:71 UHLWIir 1 0 en1 833 user150-173.wirele localhost UHS 0 0 lo0 169.254 link#5 UCS 1 0 en1 169.254.255.255 0:90:b:27:10:71 UHLSW 0 0 en1

  Read the article

• Proxying/Tunneling IPSec traffic via netcat or SOCKS?

  - by MattC

  I have a client that is using a SonicWall router as their VPN concentrator. I downloaded the client software and set up the router as a peer. My issue is that my company uses a dual DMZ setup, meaning we have an interior firewall, then a bunch of DMZ servers, then an external firewall, then finally the telco router. In this setup, the interior firewall has no way to communicate with the exterior firewall since they are on two totally separate subnets. The communication occurs through the servers that straddle the networks. In this case, I need some way to forward the ISAKMP/IPSec traffic from my desktop out to the Internet. My usual trick of using netcat on the intermediate proxy server doesn't work here since it's not TCP/UDP traffic as far as I can tell. All of my previous experience with VPN's have been using SSL-based VPN's which are clearly very easily proxy-able. Any help would be appreciated, thanks!

  Read the article

• Configure browser and VPN traffic

  - by Zachzor

  Hello everyone. I've been having a few issues with my company's VPN server. The VPN is running on a Mac Server (10.6.x) and I'm also using a Macbook (10.6.5). I've been building specific programs to gather information from IPs, and to work on this while I'm at home I need to go through our VPN to access the network. Unless I send all traffic over VPN, I'm not able to hit those specific IPs. However, I'm unable to access the internet through my web browser when I send all my traffic over VPN. I was wondering if there was a way (besides setting up a split tunnel) that I could set up a web browser to go through my current wireless connection, as opposed to going through the VPN like the rest of my applications. Wether the browser be Chrome, Firefox, or Safari doesn't matter to me. Anyone else run into this issue and find a clever way to solve it? Thank you!

  Read the article

• How can i block remote computer local or internet traffic

  - by Armen Mkrtchyan

  How can i block remote computer local or internet traffic? my Os - windows XP, which is the best program for that purpose

  Read the article

• Firewall is blocking internet traffic to OpenVPN clients

  - by user268905

  I have a virtual network setup with a Linux router/firewall connected to two private networks. An OpenVPN server in routing mode and a web server are in one of the networks. On the other are linux client machines which access the webserver and the Internet through the OpenVPN server. Also, external clients can access the OpenVPN from the Internet. The OpenVPN's server.conf is setup to use routing mode in udp, push DNS and routes to the network it is in so clients can access the webserver. Here are my very strict firewall rules. After connecting to the OpenVPN server, my clients can not access the Internet or the web server. When I allow FORWARD traffic to go through, it works just fine. The OpenVPN server has full internet connectivity. What firewall rule do I need to add to allow internet traffic to reach my clients?

  Read the article

• iptables to allow input and output traffic to and from web server only

  - by Caedmon

  I have an Elastic Search server which seems to have been exploited (it's being used for a DDoS attack having had NO firewall for about a month). As a temporary measure while I create a new one I was hoping to block all traffic to and from the server which wasn't coming from or going to our web server. Will these iptables rules achieve this: iptables -I INPUT \! --src 1.2.3.4 -m tcp -p tcp --dport 9200 -j DROP iptables -P FORWARD \! --src 1.2.3.4 DROP iptables -P OUTPUT \! --src 1.2.3.4 DROP The first rule is tried and tested but obviously wasn't preventing traffic coming from my server to other IP addresses so I was hoping I could add the second two rules to full secure it.

  Read the article

• Certain users cannot get to my server

  - by Zeno

  I am finding more and more users that report they cannot reach my server (website or services). Their tracert from that user looks like this: Tracing route to domain.com [*.*.*.255] over a maximum of 30 hops: 1 * * * Request timed out. The server is up and functional and every else reports it is fine. But there are various users who cannot get to it. I have no firewall or anything that would block anyone. Yes, the last part of the server IP is 255. Could this be causing it? http://www.dslreports.com/forum/r18539206-Last-octet-255-bug-on-Windows Or would a certain ISP be denying traffic to my server? Or something on their router level?

  Read the article

• Port based bandwidth shaping

  - by nixnotwin

  I have an interent connection with the speed of 4000k bits up and down. I want to do port based traffic shaping on a ubuntu machine, which acts as router. eth0 is the WAN interface. This is how I would like to allocate bandwidth: For ports 80 and 445 the bandwidth usage can go upto 90% For ports above 1024 upto 65535 the bandwidth usage can go upto 10% For remaining ports the bandwidth usage can go upto 40% The easiest way for achieving the above is using a router with tomato firmware. I have used it and it is very efficient. I want to try if it can be done on a Ubuntu or any GNU/Linux machine. I have googled extensively about the topic and I feel there isn't much information.

  Read the article

• Nginx Rate Limiting by Referrer?

  - by SteveEdson

  I've successfully set up rate limiting on IP addresses like so, limit_req_zone $binary_remote_addr zone=one:10m rate=1r/s; But I was wondering if its possible to do the same on referrers? For example, if a site gets placed in an iframe on a third party site, which generates too much traffic to handle. I can't find any nginx variables for the referrer anywhere. Is this possible? Or can the solution be achieved in a different way? Thanks.

  Read the article

• Barring connections if VPN is down.

  - by Majid

  I have a VPN account and use it for sensitive communication. However the VPN connection sometimes is dropped while my main connection to the internet is still alive. The pages I visit through VPN are on HTTP (not secure) and have javascript code which pings the host every minute or so on a timer. So it happens sometimes that the VPN connection is dropped and yet js sends a request to the server (with the cookies). How could I restrict connections so they only happen if the VPN is live? Edit - Some required details were missing OS: Windows XP SP2 Browser (mostly used): Google Chrome Firewall: Windows default Sites to filter: not all traffic but all in a list of sites like abc.com, xyz.com

  Read the article

• setup advanced filtering and access restrictions on dd-wrt using iptables

  - by Nova deViator

  I have a linksys WRT54GL router with a DD-WRT installed and I want to setup some advanced filtering that seem to not be available through "Access restrictions" web gui option. I guess I would be using IPTABLES then. I have ssh access to router and can run iptables, but I'm not so experienced with iptables. So here are my needs: my policy would be deny all first and then allow exceptions allow all http (port 80) access to WAN through wireless allow all other traffic only to PCs with specific MAC addresses allow internet access to PC with specific MAC address according to schedule (let's say everyday between 18:00-21:00) is this possible to setup with IPtables? could somebody help me a bit with it? or should go and RTFM?

  Read the article

• How to choose an open source, Asterisk friendly firewall?

  - by Lucas

  I'm in pain. We are moving to a SIP based VOIP system and for whatever reason, we could not get our hosted Asterisk solution to work with our Sonicwall. Our VOIP provider gave up and is recommending an open source vendor, pfSense. A little background: We have about 30 users in our network. We use a few IPSec VPN connections for remote networks. I would like, but don't need, application layer filtering. We're active internet users, so properly traffic shaping is probably a concern. How can I tell if an open source firewall will handle VOIP setup smoothly with a hosted Asterisk system?

  Read the article

• Iptables and counters

  - by mehturt

  I'm trying to use iptables counters with munin to monitor traffic of hosts on my local subnet. For each host I set up a rule like this: iptables -I OUTPUT -d $ip This should count the packets going from firewall to $ip, correct? I found out that this does not seem to count all packets. I start tcpdump on my router (Linux) and I see packets to $ip that are not counted. For example I check number of packets for rule to my phone IP. I start tcpdump, refresh Gmail on my phoone, I see packets in tcpdump's output but iptables rule counters are not incremented. Then I open a web page on the same phone and the counters are incremented. What could be the reason?

  Read the article

• valgrind on server process

  - by Pigol

  hi i am new to valgrind. I know how to run valgrind on executable files from command line. But how do you run valgrind on server processes like apache/myqld/traffic server etc .. I want to run valgrind on traffic server (http://incubator.apache.org/projects/trafficserver.html) to detect some memory leaks taking place in the plugin I have written. Any suggestions ? thanks, pigol

  Read the article

• Is there an application that can monitor the network and API usage of an .exe ?

  - by user335216

  Is there an application that can monitor the network and API usage of an .exe ? I am looking for an app that can monitor: - Network traffic and or just HTTP traffic - Windows API calls For a delphi exe which I do not have the source for. Any suggestions. Thankyou.

  Read the article

• Outbound traffic being blocked for MIP/VIPped servers (Juniper SSG5)

  - by Mark S. Rasmussen

  As we've been having some problems with sporadic packet loss, I've been preparing a replacement router (also an SSG5) for our current Juniper SSG5. I've setup the new SSG5 identically to the old one. We have a /29 IP range with a single IP setup as a MIP map to a server and two others being used for VIP maps. Each VIP/MIP is accompanied by relevant policies. Long story short - we tried connected the new SSG5 and some things were not working as they should. No problem, I just reconnected the old one. However, some things are still broken, even when I reconnected the old one. I fear I may have inadvertently changed some settings while browsing through old settings in my attempt to reconfigure the new SSG5 unit. All inbound traffic seems to work as expected. However, the 192.168.2.202 server can't initiate any outbound connections. It works perfectly on the local network, but any pings or DNS lookups to external IP's fail. The MIP & VIP map to it works perfectly - I can access it through HTTP and RDP without issues. Any tips on what to debug, or where I've messed up my config? I've attached the full config here (with anonymized IPs): set clock timezone 1 set vrouter trust-vr sharable set vrouter "untrust-vr" exit set vrouter "trust-vr" unset auto-route-export exit set service "MyVOIP_UDP4569" protocol udp src-port 0-65535 dst-port 4569-4569 set service "MyVOIP_TCP22" protocol tcp src-port 0-65535 dst-port 22-22 set service "MyRDP" protocol tcp src-port 0-65535 dst-port 3389-3389 set service "MyRsync" protocol tcp src-port 0-65535 dst-port 873-873 set service "NZ_FTP" protocol tcp src-port 0-65535 dst-port 40000-41000 set service "NZ_FTP" + tcp src-port 0-65535 dst-port 21-21 set service "PPTP-VPN" protocol 47 src-port 2048-2048 dst-port 2048-2048 set service "PPTP-VPN" + tcp src-port 1024-65535 dst-port 1723-1723 set service "NZ_FMS_1935" protocol tcp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_1935" + udp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_8080" protocol tcp src-port 0-65535 dst-port 8080-8080 set service "CrashPlan Server" protocol tcp src-port 0-65535 dst-port 4280-4280 set service "CrashPlan Console" protocol tcp src-port 0-65535 dst-port 4282-4282 unset alg sip enable set auth-server "Local" id 0 set auth-server "Local" server-name "Local" set auth default auth server "Local" set auth radius accounting port 1646 set admin auth timeout 10 set admin auth server "Local" set admin format dos set vip multi-port set zone "Trust" vrouter "trust-vr" set zone "Untrust" vrouter "trust-vr" set zone "DMZ" vrouter "trust-vr" set zone "VLAN" vrouter "trust-vr" set zone "Untrust-Tun" vrouter "trust-vr" set zone "Trust" tcp-rst set zone "Untrust" block unset zone "Untrust" tcp-rst set zone "DMZ" tcp-rst set zone "VLAN" block unset zone "VLAN" tcp-rst set zone "Untrust" screen tear-drop set zone "Untrust" screen syn-flood set zone "Untrust" screen ping-death set zone "Untrust" screen ip-filter-src set zone "Untrust" screen land set zone "V1-Untrust" screen tear-drop set zone "V1-Untrust" screen syn-flood set zone "V1-Untrust" screen ping-death set zone "V1-Untrust" screen ip-filter-src set zone "V1-Untrust" screen land set interface ethernet0/0 phy full 100mb set interface ethernet0/3 phy full 100mb set interface ethernet0/4 phy full 100mb set interface ethernet0/5 phy full 100mb set interface ethernet0/6 phy full 100mb set interface "ethernet0/0" zone "Untrust" set interface "ethernet0/1" zone "Null" set interface "bgroup0" zone "Trust" set interface "bgroup1" zone "Trust" set interface "bgroup2" zone "Trust" set interface bgroup2 port ethernet0/2 set interface bgroup0 port ethernet0/3 set interface bgroup0 port ethernet0/4 set interface bgroup1 port ethernet0/5 set interface bgroup1 port ethernet0/6 unset interface vlan1 ip set interface ethernet0/0 ip 212.242.193.18/29 set interface ethernet0/0 route set interface bgroup0 ip 192.168.1.1/24 set interface bgroup0 nat set interface bgroup1 ip 192.168.2.1/24 set interface bgroup1 nat set interface bgroup2 ip 192.168.3.1/24 set interface bgroup2 nat set interface ethernet0/0 gateway 212.242.193.17 unset interface vlan1 bypass-others-ipsec unset interface vlan1 bypass-non-ip set interface ethernet0/0 ip manageable set interface bgroup0 ip manageable set interface bgroup1 ip manageable set interface bgroup2 ip manageable set interface bgroup0 manage mtrace unset interface bgroup1 manage ssh unset interface bgroup1 manage telnet unset interface bgroup1 manage snmp unset interface bgroup1 manage ssl unset interface bgroup1 manage web unset interface bgroup2 manage ssh unset interface bgroup2 manage telnet unset interface bgroup2 manage snmp unset interface bgroup2 manage ssl unset interface bgroup2 manage web set interface ethernet0/0 vip 212.242.193.19 2048 "PPTP-VPN" 192.168.1.131 set interface ethernet0/0 vip 212.242.193.19 + 4280 "CrashPlan Server" 192.168.1.131 set interface ethernet0/0 vip 212.242.193.19 + 4282 "CrashPlan Console" 192.168.1.131 set interface ethernet0/0 vip 212.242.193.22 22 "MyVOIP_TCP22" 192.168.2.127 set interface ethernet0/0 vip 212.242.193.22 + 4569 "MyVOIP_UDP4569" 192.168.2.127 set interface ethernet0/0 vip 212.242.193.22 + 3389 "MyRDP" 192.168.2.202 set interface ethernet0/0 vip 212.242.193.22 + 873 "MyRsync" 192.168.2.201 set interface ethernet0/0 vip 212.242.193.22 + 80 "HTTP" 192.168.2.202 set interface ethernet0/0 vip 212.242.193.22 + 2048 "PPTP-VPN" 192.168.2.201 set interface ethernet0/0 vip 212.242.193.22 + 8080 "NZ_FMS_8080" 192.168.2.216 set interface ethernet0/0 vip 212.242.193.22 + 1935 "NZ_FMS_1935" 192.168.2.216 set interface bgroup0 dhcp server service set interface bgroup1 dhcp server service set interface bgroup2 dhcp server service set interface bgroup0 dhcp server auto set interface bgroup1 dhcp server auto set interface bgroup2 dhcp server auto set interface bgroup0 dhcp server option domainname iplan set interface bgroup0 dhcp server option dns1 192.168.1.131 set interface bgroup1 dhcp server option domainname nzlan set interface bgroup1 dhcp server option dns1 192.168.2.202 set interface bgroup2 dhcp server option dns1 8.8.8.8 set interface bgroup2 dhcp server option wins1 8.8.4.4 set interface bgroup0 dhcp server ip 192.168.1.2 to 192.168.1.116 set interface bgroup1 dhcp server ip 192.168.2.2 to 192.168.2.116 set interface bgroup2 dhcp server ip 192.168.3.2 to 192.168.3.126 unset interface bgroup0 dhcp server config next-server-ip unset interface bgroup1 dhcp server config next-server-ip unset interface bgroup2 dhcp server config next-server-ip set interface "ethernet0/0" mip 212.242.193.21 host 192.168.2.202 netmask 255.255.255.255 vr "trust-vr" set interface "serial0/0" modem settings "USR" init "AT&F" set interface "serial0/0" modem settings "USR" active set interface "serial0/0" modem speed 115200 set interface "serial0/0" modem retry 3 set interface "serial0/0" modem interval 10 set interface "serial0/0" modem idle-time 10 set pak-poll p1queue pak-threshold 96 set pak-poll p2queue pak-threshold 32 set flow tcp-mss unset flow tcp-syn-check set dns host dns1 0.0.0.0 set dns host dns2 0.0.0.0 set dns host dns3 0.0.0.0 set address "Trust" "192.168.1.0/24" 192.168.1.0 255.255.255.0 set address "Trust" "192.168.2.0/24" 192.168.2.0 255.255.255.0 set address "Trust" "192.168.3.0/24" 192.168.3.0 255.255.255.0 set ike respond-bad-spi 1 unset ike ikeid-enumeration unset ike dos-protection unset ipsec access-session enable set ipsec access-session maximum 5000 set ipsec access-session upper-threshold 0 set ipsec access-session lower-threshold 0 set ipsec access-session dead-p2-sa-timeout 0 unset ipsec access-session log-error unset ipsec access-session info-exch-connected unset ipsec access-session use-error-log set l2tp default ppp-auth chap set url protocol websense exit set policy id 1 from "Trust" to "Untrust" "Any" "Any" "ANY" permit traffic set policy id 1 exit set policy id 2 from "Untrust" to "Trust" "Any" "VIP(212.242.193.19)" "PPTP-VPN" permit traffic set policy id 2 exit set policy id 3 from "Untrust" to "Trust" "Any" "VIP(212.242.193.22)" "HTTP" permit traffic priority 0 set policy id 3 set service "MyRDP" set service "MyRsync" set service "MyVOIP_TCP22" set service "MyVOIP_UDP4569" exit set policy id 6 from "Trust" to "Trust" "192.168.1.0/24" "192.168.2.0/24" "ANY" deny set policy id 6 exit set policy id 7 from "Trust" to "Trust" "192.168.2.0/24" "192.168.1.0/24" "ANY" deny set policy id 7 exit set policy id 8 from "Trust" to "Trust" "192.168.3.0/24" "192.168.1.0/24" "ANY" deny set policy id 8 exit set policy id 9 from "Trust" to "Trust" "192.168.3.0/24" "192.168.2.0/24" "ANY" deny set policy id 9 exit set policy id 10 from "Untrust" to "Trust" "Any" "MIP(212.242.193.21)" "NZ_FTP" permit set policy id 10 exit set policy id 11 from "Untrust" to "Trust" "Any" "VIP(212.242.193.22)" "PPTP-VPN" permit set policy id 11 exit set policy id 12 from "Untrust" to "Trust" "Any" "VIP(212.242.193.22)" "NZ_FMS_1935" permit set policy id 12 set service "NZ_FMS_8080" exit set policy id 13 from "Untrust" to "Trust" "Any" "VIP(212.242.193.19)" "CrashPlan Console" permit set policy id 13 set service "CrashPlan Server" exit set nsmgmt bulkcli reboot-timeout 60 set ssh version v2 set config lock timeout 5 set snmp port listen 161 set snmp port trap 162 set vrouter "untrust-vr" exit set vrouter "trust-vr" unset add-default-route exit set vrouter "untrust-vr" exit set vrouter "trust-vr" exit

  Read the article

• High apache load but little traffic logged

  - by nrambeck

  I recently installed Varnish to sit in front of Apache on a dedicated server running a single site. It appears to be working well, but the load on Apache is still very high. What doesn't make sense is that the Apache access log shows almost no traffic getting past Varnish. When I tail the apache log I see about 1-3 hits per second come through. Here is what the load on Apache looks like : USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND apache 13834 8.1 1.0 107716 34164 ? S 08:24 0:02 /usr/sbin/httpd apache 13835 8.1 1.0 107716 33856 ? S 08:24 0:02 /usr/sbin/httpd apache 11483 7.9 0.9 105916 30788 ? S 08:23 0:06 /usr/sbin/httpd apache 12255 7.5 1.0 107476 33312 ? S 08:24 0:04 /usr/sbin/httpd apache 9340 7.2 1.1 107732 34916 ? R 08:23 0:09 /usr/sbin/httpd apache 12029 6.8 0.9 106908 30416 ? S 08:24 0:04 /usr/sbin/httpd apache 11577 6.7 1.0 107192 34180 ? S 08:24 0:05 /usr/sbin/httpd apache 11486 6.6 1.0 106176 33112 ? S 08:23 0:05 /usr/sbin/httpd apache 11796 6.4 1.0 106936 31916 ? S 08:24 0:04 /usr/sbin/httpd apache 13815 6.3 1.0 107988 34464 ? S 08:24 0:02 /usr/sbin/httpd apache 18089 6.3 1.3 107444 43212 ? S 08:11 0:52 /usr/sbin/httpd apache 11797 5.9 1.0 107716 34580 ? S 08:24 0:04 /usr/sbin/httpd apache 7655 5.9 0.0 0 0 ? Z 08:22 0:09 [httpd] <defunct> mysql 8033 5.9 6.2 318240 199512 ? Sl May14 352:34 /usr/libexec/mysqld --basedir=/usr --datadir=/var/lib/mysql --user=mysql --pid-file=/va apache 11488 5.8 0.9 106924 31632 ? S 08:23 0:04 /usr/sbin/httpd apache 9375 5.7 1.1 106956 35552 ? S 08:23 0:07 /usr/sbin/httpd apache 3551 5.6 1.1 106956 36140 ? S 08:20 0:14 /usr/sbin/httpd apache 7657 5.6 1.0 106968 32472 ? S 08:22 0:09 /usr/sbin/httpd apache 11433 5.6 1.0 107716 34396 ? S 08:23 0:04 /usr/sbin/httpd apache 5505 5.5 1.1 106944 34924 ? S 08:21 0:12 /usr/sbin/httpd apache 7172 5.3 1.1 106972 35368 ? S 08:22 0:09 /usr/sbin/httpd apache 10088 5.2 0.9 106160 31240 ? S 08:23 0:04 /usr/sbin/httpd apache 7656 5.1 1.0 106436 34388 ? S 08:22 0:08 /usr/sbin/httpd apache 3468 5.0 1.1 107716 35968 ? S 08:20 0:13 /usr/sbin/httpd apache 14242 4.8 1.0 107728 33032 ? S 08:25 0:00 /usr/sbin/httpd apache 3578 4.8 1.1 107988 35964 ? S 08:20 0:12 /usr/sbin/httpd apache 28192 4.8 1.2 106944 38060 ? S 08:17 0:23 /usr/sbin/httpd apache 3277 4.6 1.1 106956 35688 ? S 08:20 0:13 /usr/sbin/httpd apache 15434 3.7 0.7 106908 24684 ? S 08:25 0:00 /usr/sbin/httpd There is a default apache log and then one other VirtualHost log setup. I'm concerned that Apache is handling some kind of traffic that is not being logged. Is that possible? And is there anything I can do to capture that traffic?

  Read the article

• Measuring 'total bytes written' under Linux

  - by badnews

  We're quite interested in exploring the possibility of using SSD drives in a server environment. However, one thing that we need to establish is expected drive longevity. According to this article manufacturer's are reporting drive endurance in terms of 'total bytes written' (TBW). E.g. from that article a Crucial C400 SSD is rated at 72TB TBW. Do any scripts/tools exist under the Linux ecosystem to help us measure TBW? (and then make a more educated decision on the feasibility of using SSD drives)

  Read the article

• Change Photoshop CS4 ruler units from inches to pixels

  - by Derek Adair

  How do I change the ruler units from inches to pixels in Photoshop CS4?

  Read the article

• unable to sniff traffic despite network interface being in monitor or promiscuous mode

  - by user65126

  I'm trying to sniff out my network's wireless traffic but am having issues. I'm able to put the card in monitor mode, but am unable to see any traffic except broadcasts, multicasts and probe/beacon frames. I have two network interfaces on this laptop. One is connected normally to 'linksys' and the other is in monitor mode. The interface in monitor mode is on the right channel. I'm not associated with the access point because, as I understand, I don't need to if using monitor mode (vs promiscuous). When I try to ping the router ip, I'm not seeing that traffic show up in wireshark. Here's my ifconfig settings: daniel@seasonBlack:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1f:29:9e:b2:89 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:112 errors:0 dropped:0 overruns:0 frame:0 TX packets:112 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8518 (8.5 KB) TX bytes:8518 (8.5 KB) wlan0 Link encap:Ethernet HWaddr 00:21:00:34:f7:f4 inet addr:192.168.1.116 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::221:ff:fe34:f7f4/64 Scope:Link UP BROADCAST RUNNING MTU:1500 Metric:1 RX packets:9758 errors:0 dropped:0 overruns:0 frame:0 TX packets:4869 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3291516 (3.2 MB) TX bytes:677386 (677.3 KB) wlan1 Link encap:UNSPEC HWaddr 00-02-72-7B-92-53-33-34-00-00-00-00-00-00-00-00 UP BROADCAST NOTRAILERS PROMISC ALLMULTI MTU:1500 Metric:1 RX packets:112754 errors:0 dropped:0 overruns:0 frame:0 TX packets:101 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:18569124 (18.5 MB) TX bytes:12874 (12.8 KB) wmaster0 Link encap:UNSPEC HWaddr 00-21-00-34-F7-F4-00-00-00-00-00-00-00-00-00-00 UP RUNNING MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wmaster1 Link encap:UNSPEC HWaddr 00-02-72-7B-92-53-00-00-00-00-00-00-00-00-00-00 UP RUNNING MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Here's my iwconfig settings: daniel@seasonBlack:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions. wmaster0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:"linksys" Mode:Managed Frequency:2.437 GHz Access Point: 00:18:F8:D6:17:34 Bit Rate=54 Mb/s Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=68/70 Signal level=-42 dBm Noise level=-69 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 wmaster1 no wireless extensions. wlan1 IEEE 802.11bg Mode:Monitor Frequency:2.437 GHz Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Here's how I know I'm on the right channel: daniel@seasonBlack:~$ iwlist channel lo no frequency information. eth0 no frequency information. wmaster0 no frequency information. wlan0 11 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Current Frequency=2.437 GHz (Channel 6) wmaster1 no frequency information. wlan1 11 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Current Frequency=2.437 GHz (Channel 6)

  Read the article

• Limiting bandwidth on internal interface on Linux gateway

  - by Jack Scott

  I am responsible for a Linux-based (it runs Debian) branch office router that takes a single high-speed Internet connection (eth2) and turns it into about 20 internal networks, each with a seperate subnet (192.168.1.0/24 to 192.168.20.0/24) and a seperate VLAN (eth0.101 to eth0.120). I am trying to restrict bandwidth on one of the internal subnets that is consistently chewing up more bandwidth than it should. What is the best way to do this? My first try at this was with wondershaper, which I heard about on SuperUser here. Unfortunately, this is useful for exactly the opposite situation that I have... it's useful on the client side, not on the Internet side. My second attempt was using the script found at http://www.topwebhosts.org/tools/traffic-control.php, which I modified so the active part is: tc qdisc add dev eth0.113 root handle 13: htb default 100 tc class add dev eth0.113 parent 13: classid 13:1 htb rate 3mbps tc class add dev eth0.113 parent 13: classid 13:2 htb rate 3mbps tc filter add dev eth0.113 protocol ip parent 13:0 prio 1 u32 match ip dst 192.168.13.0/24 flowid 13:1 tc filter add dev eth0.113 protocol ip parent 13:0 prio 1 u32 match ip src 192.168.13.0/24 flowid 13:2 What I want this to do is restrict the bandwidth on VLAN 113 (subnet 192.168.13.0/24) to 3mbit up and 3mbit down. Unfortunately, it seems to have no effect at all! I'm very inexperienced with the tc command, so any help getting this working would be appreciated.

  Read the article

< Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >