Search Results

Search found 8354 results on 335 pages for 'welton v3 50'.

Page 23/335 | < Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >

  • vSphere ESX 5.5 hosts cannot connect to NFS Server

    - by Gerald
    Summary: My problem is I cannot use the QNAP NFS Server as an NFS datastore from my ESX hosts despite the hosts being able to ping it. I'm utilising a vDS with LACP uplinks for all my network traffic (including NFS) and a subnet for each vmkernel adapter. Setup: I'm evaluating vSphere and I've got two vSphere ESX 5.5 hosts (node1 and node2) and each one has 4x NICs. I've teamed them all up using LACP/802.3ad with my switch and then created a distributed switch between the two hosts with each host's LAG as the uplink. All my networking is going through the distributed switch, ideally, I want to take advantage of DRS and the redundancy. I have a domain controller VM ("Central") and vCenter VM ("vCenter") running on node1 (using node1's local datastore) with both hosts attached to the vCenter instance. Both hosts are in a vCenter datacenter and a cluster with HA and DRS currently disabled. I have a QNAP TS-669 Pro (Version 4.0.3) (TS-x69 series is on VMware Storage HCL) which I want to use as the NFS server for my NFS datastore, it has 2x NICs teamed together using 802.3ad with my switch. vmkernel.log: The error from the host's vmkernel.log is not very useful: NFS: 157: Command: (mount) Server: (10.1.2.100) IP: (10.1.2.100) Path: (/VM) Label (datastoreNAS) Options: (None) cpu9:67402)StorageApdHandler: 698: APD Handle 509bc29f-13556457 Created with lock[StorageApd0x411121] cpu10:67402)StorageApdHandler: 745: Freeing APD Handle [509bc29f-13556457] cpu10:67402)StorageApdHandler: 808: APD Handle freed! cpu10:67402)NFS: 168: NFS mount 10.1.2.100:/VM failed: Unable to connect to NFS server. Network Setup: Here is my distributed switch setup (JPG). Here are my networks. 10.1.1.0/24 VM Management (VLAN 11) 10.1.2.0/24 Storage Network (NFS, VLAN 12) 10.1.3.0/24 VM vMotion (VLAN 13) 10.1.4.0/24 VM Fault Tolerance (VLAN 14) 10.2.0.0/24 VM's Network (VLAN 20) vSphere addresses 10.1.1.1 node1 Management 10.1.1.2 node2 Management 10.1.2.1 node1 vmkernel (For NFS) 10.1.2.2 node2 vmkernel (For NFS) etc. Other addresses 10.1.2.100 QNAP TS-669 (NFS Server) 10.2.0.1 Domain Controller (VM on node1) 10.2.0.2 vCenter (VM on node1) I'm using a Cisco SRW2024P Layer-2 switch (Jumboframes enabled) with the following setup: LACP LAG1 for node1 (Ports 1 through 4) setup as VLAN trunk for VLANs 11-14,20 LACP LAG2 for my router (Ports 5 through 8) setup as VLAN trunk for VLANs 11-14,20 LACP LAG3 for node2 (Ports 9 through 12) setup as VLAN trunk for VLANs 11-14,20 LACP LAG4 for the QNAP (Ports 23 and 24) setup to accept untagged traffic into VLAN 12 Each subnet is routable to another, although, connections to the NFS server from vmk1 shouldn't need it. All other traffic (vSphere Web Client, RDP etc.) goes through this setup fine. I tested the QNAP NFS server beforehand using ESX host VMs atop of a VMware Workstation setup with a dedicated physical NIC and it had no problems. The ACL on the NFS Server share is permissive and allows all subnet ranges full access to the share. I can ping the QNAP from node1 vmk1, the adapter that should be used to NFS: ~ # vmkping -I vmk1 10.1.2.100 PING 10.1.2.100 (10.1.2.100): 56 data bytes 64 bytes from 10.1.2.100: icmp_seq=0 ttl=64 time=0.371 ms 64 bytes from 10.1.2.100: icmp_seq=1 ttl=64 time=0.161 ms 64 bytes from 10.1.2.100: icmp_seq=2 ttl=64 time=0.241 ms Netcat does not throw an error: ~ # nc -z 10.1.2.100 2049 Connection to 10.1.2.100 2049 port [tcp/nfs] succeeded! The routing table of node1: ~ # esxcfg-route -l VMkernel Routes: Network Netmask Gateway Interface 10.1.1.0 255.255.255.0 Local Subnet vmk0 10.1.2.0 255.255.255.0 Local Subnet vmk1 10.1.3.0 255.255.255.0 Local Subnet vmk2 10.1.4.0 255.255.255.0 Local Subnet vmk3 default 0.0.0.0 10.1.1.254 vmk0 VM Kernel NIC info ~ # esxcfg-vmknic -l Interface Port Group/DVPort IP Family IP Address Netmask Broadcast MAC Address MTU TSO MSS Enabled Type vmk0 133 IPv4 10.1.1.1 255.255.255.0 10.1.1.255 00:50:56:66:8e:5f 1500 65535 true STATIC vmk0 133 IPv6 fe80::250:56ff:fe66:8e5f 64 00:50:56:66:8e:5f 1500 65535 true STATIC, PREFERRED vmk1 164 IPv4 10.1.2.1 255.255.255.0 10.1.2.255 00:50:56:68:f5:1f 1500 65535 true STATIC vmk1 164 IPv6 fe80::250:56ff:fe68:f51f 64 00:50:56:68:f5:1f 1500 65535 true STATIC, PREFERRED vmk2 196 IPv4 10.1.3.1 255.255.255.0 10.1.3.255 00:50:56:66:18:95 1500 65535 true STATIC vmk2 196 IPv6 fe80::250:56ff:fe66:1895 64 00:50:56:66:18:95 1500 65535 true STATIC, PREFERRED vmk3 228 IPv4 10.1.4.1 255.255.255.0 10.1.4.255 00:50:56:72:e6:ca 1500 65535 true STATIC vmk3 228 IPv6 fe80::250:56ff:fe72:e6ca 64 00:50:56:72:e6:ca 1500 65535 true STATIC, PREFERRED Things I've tried/checked: I'm not using DNS names to connect to the NFS server. Checked MTU. Set to 9000 for vmk1, dvSwitch and Cisco switch and QNAP. Moved QNAP onto VLAN 11 (VM Management, vmk0) and gave it an appropriate address, still had same issue. Changed back afterwards of course. Tried initiating the connection of NAS datastore from vSphere Client (Connected to vCenter or directly to host), vSphere Web Client and the host's ESX Shell. All resulted in the same problem. Tried a path name of "VM", "/VM" and "/share/VM" despite not even having a connection to server. I plugged in a linux system (10.1.2.123) into a switch port configured for VLAN 12 and tried mounting the NFS share 10.1.2.100:/VM, it worked successfully and I had read-write access to it I tried disabling the firewall on the ESX host esxcli network firewall set --enabled false I'm out of ideas on what to try next. The things I'm doing differently from my VMware Workstation setup is the use of LACP with a physical switch and a virtual distributed switch between the two hosts. I'm guessing the vDS is probably the source of my troubles but I don't know how to fix this problem without eliminating it.

    Read the article

  • Network outside internal not reaching TMG Forefront 2010 (Hyper-V environment)

    - by Pascal
    Below is my environment: I have 1 physical machine running Windows 2008 R2, with the Hyper-V role. This machine has 3 physical NICs: One for Internet One for Internal Network One for Wireless Network All 3 have their respective Virtual Networks in Hyper-V, and I have an extra Private virutal machine network for a DMZ Network. In one of the virtual machines, I have TMG Forefront 2010 SP1 installed, with all 4 networks available to it. Below is the IPCONFIG /ALL at the firewall: Windows IP Configuration Host Name . . . . . . . . . . . . : FRW-EXP1-02 Primary Dns Suffix . . . . . . . : exp1.eti.br Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : Yes WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : exp1.eti.br Ethernet adapter Internet: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft Virtual Machine Bus Network Adapter #4 Physical Address. . . . . . . . . : 00-15-5D-01-06-0E DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::6d05:6033:4cfc:bdf5%15(Preferred) IPv4 Address. . . . . . . . . . . : 189.100.110.xxx(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.240.0 Lease Obtained. . . . . . . . . . : quarta-feira, 5 de janeiro de 2011 11:17:24 Lease Expires . . . . . . . . . . : quarta-feira, 5 de janeiro de 2011 16:07:02 Default Gateway . . . . . . . . . : 189.100.96.xxx DHCP Server . . . . . . . . . . . : 201.6.2.43 DHCPv6 IAID . . . . . . . . . . . : 436213085 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-14-6D-75-6F-00-15-5D-01-06-0B DNS Servers . . . . . . . . . . . : 201.6.2.163 201.6.2.43 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter Rede Interna: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft Virtual Machine Bus Network Adapter #3 Physical Address. . . . . . . . . : 00-15-5D-01-06-0C DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::51ff:4723:ce4c:bbc3%14(Preferred) IPv4 Address. . . . . . . . . . . : 10.50.75.10(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : DHCPv6 IAID . . . . . . . . . . . : 352327005 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-14-6D-75-6F-00-15-5D-01-06-0B DNS Servers . . . . . . . . . . . : 10.50.75.1 10.50.75.2 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter DMZ: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft Virtual Machine Bus Network Adapter #2 Physical Address. . . . . . . . . : 00-15-5D-01-06-0A DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::d4c5:75cf:e9aa:73e1%13(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.10.1(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : DHCPv6 IAID . . . . . . . . . . . : 301995357 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-14-6D-75-6F-00-15-5D-01-06-0B DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1 fec0:0:0:ffff::2%1 fec0:0:0:ffff::3%1 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter Wireless: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft Virtual Machine Bus Network Adapter Physical Address. . . . . . . . . : 00-15-5D-01-06-0B DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::459:8ca6:d02:8da1%11(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.1.10(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : DHCPv6 IAID . . . . . . . . . . . : 234886493 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-14-6D-75-6F-00-15-5D-01-06-0B DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1 fec0:0:0:ffff::2%1 fec0:0:0:ffff::3%1 NetBIOS over Tcpip. . . . . . . . : Enabled I have the Networks below at Forefront: External: IP addresses external to the Forefront TMG Networks Internal: 10.50.75.0 - 10.50.75.255 Local Host: Perimiter: 192.168.10.0 - 192.168.10.255 Wireless: 192.168.1.0 - 192.168.1.255 In the Networks Rules, I have: 1 => Route => Local Host => All Networks 2 => Route => Quarantined; VPN => Internal 3 => NAT => Internal; VPN => Perimiter 4 => NAT => Internal; Perimiter; Quarantined; VPN; Wireless => External My problem is that I can only communicate with the Internal and External networks. If a ping www.google.com or 10.50.75.21 from the Forefront VM, I get answer backs without a problem. If I try to ping a machine at the Perimiter network or the Wireless network, it doesn't get routed back to Forefront, and it's the default gateway on all Networks. Here as ping samples: PS C:\Users\Administrator.TPB1> ping www.google.com Pinging www.l.google.com [64.233.163.104] with 32 bytes of data: Reply from 64.233.163.104: bytes=32 time=11ms TTL=58 Reply from 64.233.163.104: bytes=32 time=8ms TTL=58 Ping statistics for 64.233.163.104: Packets: Sent = 2, Received = 2, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 8ms, Maximum = 11ms, Average = 9ms Control-C PS C:\Users\Administrator.TPB1> ping 10.50.75.21 Pinging 10.50.75.21 with 32 bytes of data: Reply from 10.50.75.21: bytes=32 time=1ms TTL=128 Reply from 10.50.75.21: bytes=32 time=1ms TTL=128 Reply from 10.50.75.21: bytes=32 time=1ms TTL=128 Reply from 10.50.75.21: bytes=32 time=1ms TTL=128 Ping statistics for 10.50.75.21: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 1ms, Maximum = 1ms, Average = 1ms PS C:\Users\Administrator.TPB1> ping 192.168.10.3 Pinging 192.168.10.3 with 32 bytes of data: Reply from 192.168.10.1: Destination host unreachable. Request timed out. Request timed out. Request timed out. Ping statistics for 192.168.10.3: Packets: Sent = 4, Received = 1, Lost = 3 (75% loss), PS C:\Users\Administrator.TPB1> The ping to the 192.168.10.3 gets the Destination host unreachable. Below is the ipconfig for the perimiter VM: PS C:\Users\Administrator.Administrator> ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : app-exp1-02 Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Unkown IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft Virtual Machine Bus Network Adapter Physical Address. . . . . . . . . : 00-15-5D-01-06-08 DHCP Enabled. . . . . . . . . . . : No IPv4 Address. . . . . . . . . . . : 192.168.10.3 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.10.1 DNS Servers . . . . . . . . . . . : 201.6.2.163 201.6.2.43 Trying to ping 192.168.10.1 ( the gateway ) from the DMZ machine also does not work. When I use Log & Reports to monitor packets from Wireless network and Perimiter network, I don't get any packets link PING or HTTP that I try to send. But I do get a lot of spoofing messages for NETBIOS broadcasts... it's like Forefront thinks it's coming from a different network, but I don't know why. Please Help! Tks

    Read the article

  • Need help using a super scope

    - by Vdub
    I have a windows server 2008 r2 standard running our DCHP, DNS, and AD. also I have (3) HP Pro Curve 2510-G switches (J9280A). Right now our LAN is set up 192.168.50.2-192.168.50.254 on our sub-net (A) and another scope with 192.168.51.2-192.168.51.254 sub-net (B) both have sub-net mask of 255.255.255.0. The same server is our DNS which is 192.168.50.242 and our firewall (watchguard) is the gateway at 192.168.50.1. Right now the sub-net (B) does not have DHCP active so only sub-net (A) is giving a pool. My problem is that we are trying to have open WiFi on our network and i am assuming that i can use the sub-net (B) for that if i activate it and use sub-net (A) for our staff only. I have noticed that when i set up a static on a client pc and set it to 192.168.51.x i cannot use the DNS of 192.168.50.242 however i can use 8.8.8.8 and it works fine, i am guessing that because it is on a different sub-net? Forgive me as i am very new at this and dont know a lot. Is there easy way with the equipment i have to a accommodate wifi for hundreds of people without causing problems for our staff? (multiple same IP address assigns) I appreciate any and all info!

    Read the article

  • Cannot write samba shares

    - by Batsu
    Running samba 3.5 on Red Hat Enterprise 6.1 I'm having issues sharing two folders. Here is the output of testparm: [global] workgroup = DOMAINNAME server string = Samba Server Version %v interfaces = lo, eth1 bind interfaces only = Yes map to guest = Bad User log file = /var/log/samba/log.%m max log size = 50 idmap uid = 16777216-33554431 idmap gid = 16777216-33554431 hosts allow = 10.50.183.48, 10.50.184.41, 10.50.184.199, 10.50.183.160, 127.0.0.1 hosts deny = 0.0.0.0/0 cups options = raw [test] comment = test folder path = /usr/local/samba valid users = claudio write list = claudio force user = claudio read only = No create mask = 0775 directory mask = 0775 [test2] comment = another test path = /home/claudio/tst valid users = claudio write list = claudio force user = claudio read only = No create mask = 0775 From the Windows XP machine I'm connecting from I'm able to read test but not write, while for test2 I can't even access the folder (though I can see it listed). ls -l /usr/local ... drwxrwxrwx. 2 claudio claudio 4096 Dec 3 10:39 samba ... ls -l /user/local/samba total 32 -rwxrwxrwx. 1 claudio claudio 9 Nov 29 16:26 asd.txt -rwxrwxrwx. 1 claudio claudio 728 Dec 3 10:16 out.txt ... ls -l /home/claudio/ ... drwxrwxr-x. 2 claudio claudio 4096 Dec 3 09:57 tst ... ls -l /home/claudio/tst total 4 -rw-rw-r--. 1 claudio claudio 4 Dec 3 09:57 asd.txt Any suggestion?

    Read the article

  • ESXi Static IP setup with gateway on different subnet

    - by Erik Nelson
    I've got an ESXi server that I'm trying to assign a static IP to. I'm having trouble setting the gateway because (I presume) the gateway is on a different subnet. I've been able to accomplish this task on normal Linux servers by doing the following: route add 172.50.99.254 eth0 route add -net default gw 172.50.99.254 eth0 Now using the GUI config tools for ESXi I've tried setting the following IP: 172.50.5.151 Netmask: 255.255.252.0 Gateway: 172.50.99.254 The gateway does not stick, and when I try to add the gateway manually using esxcfg-route it says it has no route to the gateway IP. How can I get this static IP set correctly? (I don't have any control over the network setup).

    Read the article

  • Benefits of setting a webserver in Linux

    - by John Kent
    I wonder what main purposes and benefits can one get after he sets up a webserver running on Linux installed on a VM which is hosted by Windows and that this webserver can be used as a local host for windows ? That is, I have java application that is a webserver made on Linux, I set up the virtual machine for the windows client apps to listen to its (Linux)'s local IP address and port e.g 192.168.50.50:11111 When my webserver runs, I can use http://192.168.50.50/ as the windows's localhost address (instead of 127.0.0.1 as I usually do). Thank you

    Read the article

  • Adding Multiple Interfaces to EC2 Ubuntu 12.04

    - by nocode
    I have a m1.medium Ubuntu 12.04 instance with two ENI's. I have a VPC setup with a private and public subnet. Private: 10.50.1.0/24 Public: 10.50.101.0/24 I initiated the instance on the private subnet. I configured a NAT instance and route all servers in the private subnet internet access. The route tables on the private subnet point towards the NAT instance and the route table on the public subnet point to the internet gateway. I am trying to add a public interface on the machine so that I can put it behind a ELB. When I added the second ENI and configured a static IP in /etc/network/interfaces and restarted the network services, I can no longer access from the Public subnet to the Private Subnet. Works Private private Private public Does not work Public private From Public Private, I ran a TCPDUMp on the private machine and can see the request coming in. My guess is it's trying to route over the new Public interface instead of the Private. Here's my route: default 10.50.1.1 0.0.0.0 UG 100 0 0 eth0 10.50.1.0 * 255.255.255.0 U 0 0 0 eth0 10.50.101.0 * 255.255.255.0 U 0 0 0 eth1 My networking knowledge is limited and I believe I have to add some routes but unsure of what command/syntax needs to be.

    Read the article

  • VBA: Parse preceding numbers from string

    - by buttonsrtoys
    I need to parse into two substrings a string that always starts with numeric text followed by alphnumeric text. The strings can vary a bit, but not too much. Below are examples of incoming format and the strings I need: "00 10 50 Information to Bidders" ==> "00 10 50", "Information to Bidders" "001050 Information to Bidders" ==> "001050", "Information to Bidders" "00 10 50 - Information to Bidders" ==> "00 10 50", "Information to Bidders" "001050 -- Information to Bidders" ==> "001050", "Information to Bidders" I was hoping it would only be a half dozen lines of VBA, but my code is turning into a loop where I'm testing every character in the string to see where the changeover from numeric-only to non-numeric, then parsing the string based on the changeover location. Not a big deal, but messier than I was hoping for. Are there VBA functions that would eliminate the need to iterate through each string character?

    Read the article

  • TemplateBinding with Converter - what is wrong?

    - by MartyIX
    I'm creating a game desk. I wanted to specify field size (one field is a square) as a attached property and with this data set value of ViewPort which would draw 2x2 matrix (and tile mode would do the rest of game desk). I'm quite at loss what is wrong because the binding doesn't work. Testing line in XAML for the behaviour I would like to have: <DrawingBrush Viewport="0,0,100,100" ViewportUnits="Absolute" TileMode="None"> The game desk is based on this sample of DrawingPaint: http://msdn.microsoft.com/en-us/library/aa970904.aspx (an image is here) XAML: <Window x:Class="Sokoban.Window1" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" xmlns:local="clr-namespace:Sokoban" Title="Window1" Height="559" Width="419"> <Window.Resources> <local:FieldSizeToRectConverter x:Key="fieldSizeConverter" /> <Style x:Key="GameDesk" TargetType="{x:Type Rectangle}"> <Setter Property="local:GameDeskProperties.FieldSize" Value="50" /> <Setter Property="Fill"> <Setter.Value> <!--<DrawingBrush Viewport="0,0,100,100" ViewportUnits="Absolute" TileMode="None">--> <DrawingBrush Viewport="{TemplateBinding local:GameDeskProperties.FieldSize, Converter={StaticResource fieldSizeConverter}}" ViewportUnits="Absolute" TileMode="None"> <DrawingBrush.Drawing> <DrawingGroup> <GeometryDrawing Brush="CornflowerBlue"> <GeometryDrawing.Geometry> <RectangleGeometry Rect="0,0,100,100" /> </GeometryDrawing.Geometry> </GeometryDrawing> <GeometryDrawing Brush="Azure"> <GeometryDrawing.Geometry> <GeometryGroup> <RectangleGeometry Rect="0,0,50,50" /> <RectangleGeometry Rect="50,50,50,50" /> </GeometryGroup> </GeometryDrawing.Geometry> </GeometryDrawing> </DrawingGroup> </DrawingBrush.Drawing> </DrawingBrush> </Setter.Value> </Setter> </Style> </Window.Resources> <StackPanel> <Rectangle Style="{StaticResource GameDesk}" Width="300" Height="150" /> </StackPanel> </Window> Converter and property definition: using System; using System.Collections.Generic; using System.Text; using System.Windows.Controls; using System.Windows; using System.Diagnostics; using System.Windows.Data; namespace Sokoban { public class GameDeskProperties : Panel { public static readonly DependencyProperty FieldSizeProperty; static GameDeskProperties() { PropertyChangedCallback fieldSizeChanged = new PropertyChangedCallback(OnFieldSizeChanged); PropertyMetadata fieldSizeMetadata = new PropertyMetadata(50, fieldSizeChanged); FieldSizeProperty = DependencyProperty.RegisterAttached("FieldSize", typeof(int), typeof(GameDeskProperties), fieldSizeMetadata); } public static int GetFieldSize(DependencyObject target) { return (int)target.GetValue(FieldSizeProperty); } public static void SetFieldSize(DependencyObject target, int value) { target.SetValue(FieldSizeProperty, value); } static void OnFieldSizeChanged(DependencyObject target, DependencyPropertyChangedEventArgs e) { Debug.WriteLine("FieldSize just changed: " + e.NewValue); } } [ValueConversion(/* sourceType */ typeof(int), /* targetType */ typeof(Rect))] public class FieldSizeToRectConverter : IValueConverter { public object Convert(object value, Type targetType, object parameter, System.Globalization.CultureInfo culture) { Debug.Assert(targetType == typeof(int)); int fieldSize = int.Parse(value.ToString()); return new Rect(0, 0, 2 * fieldSize, 2 * fieldSize); } public object ConvertBack(object value, Type targetType, object parameter, System.Globalization.CultureInfo culture) { // should not be called in our example throw new NotImplementedException(); } } }

    Read the article

  • DoubleBuffering in Java

    - by DDP
    Hello there, I'm having some trouble implementing DoubleBuffer into my program. Before you faint from the wall of text, you should know that a lot of it is there just in case you need to know. The actual place where I think I'm having problems is in one method. I've recently looked up a tutorial on the gpwiki about double buffering, and decided to try and implement the code they had into the code I have that I'm trying to implement doublebuffer in. I get the following error: "java.lang.IllegalStateException: Component must have a valid peer". I don't know if it makes any difference if you know it or not, but the following is the code with the main method. This is just a Frame that displays the ChronosDisplay class inside it. I omitted irrelevant code with "..." public class CDM extends JFrame { public CDM(String str) { super("CD:M - "+str); try { ... ChronosDisplay theGame = new ChronosDisplay(str); ((Component)theGame).setFocusable(true); add(theGame); } catch(Exception e) { System.out.println("CDM ERROR: " +e); } } public static void main( String args[] ) { CDM run = new CDM("DP_Mini"); } } Here is the code where I think the problem resides (I think the problem is in the paint() method). This class is displayed in the CDM class public class ChronosDisplay extends Canvas implements Runnable { String mapName; public ChronosDisplay (String str) { mapName = str; new Thread(this).start(); setVisible(true); createBufferStrategy(2); } public void paint( Graphics window ) { BufferStrategy b = getBufferStrategy(); Graphics g = null; window.setColor(Color.white); try { g = b.getDrawGraphics(); paintMap(g); paintUnits(g); paintBullets(g); } finally { g.dispose(); } b.show(); Toolkit.getDefaultToolkit().sync(); } public void paintMap( Graphics window ) { TowerMap m = new TowerMap(); try { m = new TowerMap(mapName); for(int x=0; x<m.getRows()*50; x+=50) { for(int y = 0; y<m.getCols()*50; y+=50) { int tileType = m.getLocation(x/50,y/50); Image img; if(tileType == 0) { Tile0 t = new Tile0(x,y); t.draw(window); } ...// More similar if statements for other integers } catch(Exception e) ... } ...// Additional methods not shown here public void run() { try { while(true) { Thread.currentThread().sleep(20); repaint(); } } catch(Exception e) ... } } If you're curious (I doubt it matters), the draw() method in the Tile0 class is: public void draw( Graphics window ) { window.drawImage(img,getX(),getY(),50,50,null); } Any pointers, tips, or solutions are greatly appreciated. Thanks for your time! :D

    Read the article

  • Google Maps API v3: Turning user input coordinates to latlng?

    - by Leventhan
    I'm new with Google Maps. I'm trying to turn coordinates a user inputs to move a marker I have on my map to those coordinates. For instance, if the user inputs 50.75, 74.1 the marker will pan to that coordinate. Unfortunately, I couldn't get it to work. Here's my function: function moveMarker() { var Markerloc = document.getElementById("Markerloc").value; var newLatlng = new google.maps.LatLng(Markerloc); marker.setPosition(newLatLng) } Here's my HTML code: <input type="text" id= "Markerloc" value="Paste your coordinates" /> <input type="button" onclick="moveMarker()" value="Update Marker"> EDIT: I thought that'd fix it, but somehow, it still doesn't work. Here's my code: <script type="text/javascript"> var map; var zoomLevel; function initialize(){ var myLatlng = new google.maps.LatLng(40.65, -74); var myOptions = { zoom: 2, center: myLatlng, mapTypeId: google.maps.MapTypeId.ROADMAP, } var map = new google.maps.Map(document.getElementById('map_canvas'), myOptions); var zoomLevel = map.getZoom(); var marker = new google.maps.Marker({ position: myLatlng, map: map, draggable: true }); // Update current position info. updateMarkerPosition(myLatlng); // Add dragging event listeners. google.maps.event.addListener(marker, 'dragstart', function() { updateMarkerAddress('Dragging...'); }); google.maps.event.addListener (map, 'zoom_changed', function() { updateZoomLevel(map.getZoom()); }); google.maps.event.addListener(marker, 'drag', function() { updateMarkerStatus('Dragging...'); updateMarkerPosition(marker.getPosition()); }); google.maps.event.addListener(marker, 'dragend', function() { updateMarkerStatus('Drag ended'); geocodePosition(marker.getPosition()); }); }; var geocoder = new google.maps.Geocoder(); function geocodePosition(pos) { geocoder.geocode({ latLng: pos }, function(responses) { if (responses && responses.length > 0) { updateMarkerAddress(responses[0].formatted_address); } else { updateMarkerAddress('Cannot determine address at this location.'); } }); } function updateZoomLevel(zoomLevel){ document.getElementById('zoomLevel').innerHTML = zoomLevel; } function updateMarkerStatus(str) { document.getElementById('markerStatus').innerHTML = str; } function updateMarkerPosition(myLatlng) { document.getElementById('info').innerHTML = [ myLatlng.lat(), myLatlng.lng() ].join(', '); } function updateMarkerAddress(str) { document.getElementById('address').innerHTML = str; } function moveMarker() { var lat = parseFloat(document.getElementById('markerLat').value); var lng = parseFloat(document.getElementById('markerLng').value); var newLatLng = new google.maps.LatLng(lat, lng); marker.setPosition(newLatLng) } google.maps.event.addDomListener(window, 'load', initialize); </script> </head> <body> <div id="map_canvas" style="width: 29%; height: 50%; float: left; position: relative; background-color: rgb(229, 227, 223); overflow: hidden;"></div> <b>Zoom level: </b><div id="zoomLevel"> Scroll mousewheel</div> </div> <input type='text' id='markerLat' value='Target Latitude' /> <input type='text' id='markerLng' value='Target Longitude' /> <input type="button" onclick="moveMarker()" value="Move Marker"> </body> </html>

    Read the article

  • Not sure why I'm getting a NullPointerException when creating a Swing component

    - by Alex
    The error occurs when creating the Box object. public void drawBoard(Board board){ for(int row = 0; row < 8; row++){ for(int col = 0; col < 8; col++){ Box box = new Box(board.getSquare(col, row).getColour(), col, row); squarePanel[col][row].add(box); } } Board is given from the Game constructor here (another class): public Game() throws Throwable{ View graphics = new View(); board = new Board(); board.setDefault(); graphics.drawBoard(board); } The Board constructor looks like this: public Board(){ grid = new Square[COLUMNS][ROWS]; for(int row = 0; row < 8; row++){ for(int col = 0; col < 8; col++){ grid[col][row] = new Square(this); } } for(int row = 0; row < 8; row++){ for(int col = 0; col < 4; col++){ int odd = 2*col + 1; int even = 2*col; getSquare(odd, row).setColour(Color.BLACK); getSquare(even, row).setColour(Color.WHITE); } } } And finally the Box class: class Box extends JComponent{ Color boxColour; int col, row; public Box(Color boxColour, int col, int row){ this.boxColour = boxColour; this.col = col; this.row = row; repaint(); } public void paint(Graphics drawBox){ drawBox.setColor(boxColour); drawBox.drawRect(50*col, 50*row, 50, 50); drawBox.fillRect(50*col, 50*row, 50, 50); } } So while looping through the array, it uses the two integers as coordinates to create the Box. The coordinates are referenced and then repaint() is run. The box also gets the colour, using the two integers, from the Square in the Board class. Since the colour is already set, before the drawBoard(board) method is run, that shouldn't be a problem, right? Exception in thread "main" java.lang.NullPointerException at View.drawBoard(View.java:38) at Game.<init>(Game.java:21) at Game.main(Game.java:14) The relevant part of Square import java.awt.Color; public class Square { private Piece piece; private Board board; private Color squareColour; public Square(Board board){ this.board = board; } public void setColour(Color squareColour){ this.squareColour = squareColour; } public Color getColour(){ return squareColour; }

    Read the article

  • won't repaint a different Month after pressing button in my calendar

    - by DarkStar123
    I'm trying to build a Calendar in Java as a little project I thought of, But I can't seem to change the name of the Month every time I click the Next button. here's my code! package drawing; import javax.swing.*; import java.awt.*; import java.awt.event.*; public class Drawing_something extends JPanel{ int[] calender_squares = {1, 2, 3, 4, 5, 6, 7}; String[] Month = {"January", "February", "March", "April","May","June","July", "August","September","October","November","December"}; int i = 0; Graphics c; @Override public void paintComponent(Graphics c){ super.paintComponent(c); this.setBackground(Color.WHITE); int WIDTH = 55, HEIGHT = 65; for (int in: calender_squares) { for (int counter = 0; counter < 7; counter++){ c.drawRect(50, 50, 100, 100); c.drawRect(50, 50, 700, 500); c.copyArea(50, 50, 600, 500, 100, 0); c.copyArea(50, 50, 600, 400, 0, 100); } } for (int date = 1; date <= 30; date++) { String s = String.valueOf(date); c.drawString(s, WIDTH, HEIGHT); if (date <= 6){ WIDTH += 100; } else if (date == 7){ WIDTH = 55; HEIGHT = 165; }else if (date <= 13){ WIDTH += 100; }else if (date == 14){ WIDTH = 55; HEIGHT = 265; }else if (date <= 20){ WIDTH += 100; }else if (date == 21){ WIDTH = 55; HEIGHT = 365; }else if (date <= 27){ WIDTH += 100; }else if (date == 28){ WIDTH = 55; HEIGHT = 465; }else if (date <= 30){ WIDTH += 100; } } c.setFont(new Font("default", Font.BOLD, 40)); c.drawString(Month[i], 320, 45); } public Drawing_something(){ setLayout(new BorderLayout()); JButton N = new JButton("NEXT"); JButton B = new JButton("BACK"); JPanel P = new JPanel(); P.add(B); P.add(N); add(P, BorderLayout.SOUTH); B.addActionListener(new HandlerClass()); N.addActionListener(new NextClass()); } public class HandlerClass implements ActionListener{ public void actionPerformed(ActionEvent e){ } } public class NextClass implements ActionListener{ public void actionPerformed(ActionEvent e){ if (i == 11){ i = 0; } i = i + 1; c.drawString(Month[i], 320, 45); } } public static void main(String[] args){ JFrame mainFrame = new JFrame("Calender"); mainFrame.add(new Drawing_something()); mainFrame.setSize(850, 650); mainFrame.setDefaultCloseOperation(JFrame.EXIT_ON_CLOSE); mainFrame.setVisible(true); } } if anyone could help that would be much appreciated!! Thanks in advance!!

    Read the article

  • Why is my Internet connection randomly dropping?

    - by Jeanno
    Ever since I have installed 12.04 (clean install not an upgrade), i have been having a drop in the Internet connection. The drop in the connection can be anything from 15 seconds to about 3 mins, and then the connection comes back. This behaviour happens while I am actively browsing the Internet, or if I wake up the computer and open Firefox (sometimes I have connection and sometimes I don't) . Please note that when the internet connection is on, it is not slow (as speedtest.net results show) In the beginning, I thought it was a problem with the driver r8169 for my RTL8111/8168B Ethernet card, so I downloaded the r8168 from Realtek website, followed the detailed instructions (blacklisted r8169, changed the file to '.bsh' ...), but still the same problem persisted. So I switched to a wireless connection, and I got the same problem with internet connection dropping randomly. Any ideas? Thanks in advance Output from 'lspci -v' Code: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0 Capabilities: [e0] Vendor Specific Information: Len=0c <?> 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: f8000000-fa0fffff Prefetchable memory behind bridge: 00000000d0000000-00000000dbffffff Capabilities: [88] Subsystem: Dell Device 04a7 Capabilities: [80] Power Management version 3 Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [a0] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Capabilities: [140] Root Complex Link Kernel driver in use: pcieport Kernel modules: shpchp 00:01.1 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: f4000000-f60fffff Prefetchable memory behind bridge: 00000000c0000000-00000000cbffffff Capabilities: [88] Subsystem: Dell Device 04a7 Capabilities: [80] Power Management version 3 Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [a0] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Capabilities: [140] Root Complex Link Kernel driver in use: pcieport Kernel modules: shpchp 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 52 Memory at f6108000 (64-bit, non-prefetchable) [size=16] Capabilities: [50] Power Management version 3 Capabilities: [8c] MSI: Enable+ Count=1/1 Maskable- 64bit+ Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) (prog-if 20 [EHCI]) Subsystem: Dell Device 04a7 Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at f6107000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCI Advanced Features Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 53 Memory at f6100000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel Capabilities: [130] Root Complex Link Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 Memory behind bridge: fa400000-fa4fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: Dell Device 04a7 Capabilities: [a0] Power Management version 2 Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 0000c000-0000cfff Prefetchable memory behind bridge: 00000000dc100000-00000000dc1fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: Dell Device 04a7 Capabilities: [a0] Power Management version 2 Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 I/O behind bridge: 0000b000-0000bfff Memory behind bridge: fa300000-fa3fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: Dell Device 04a7 Capabilities: [a0] Power Management version 2 Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=06, subordinate=06, sec-latency=0 I/O behind bridge: 0000a000-0000afff Memory behind bridge: fa200000-fa2fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: Dell Device 04a7 Capabilities: [a0] Power Management version 2 Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) (prog-if 20 [EHCI]) Subsystem: Dell Device 04a7 Flags: bus master, medium devsel, latency 0, IRQ 23 Memory at f6106000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCI Advanced Features Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge: Intel Corporation P67 Express Chipset Family LPC Controller (rev 05) Subsystem: Dell Device 04a7 Flags: bus master, medium devsel, latency 0 Capabilities: [e0] Vendor Specific Information: Len=0c <?> Kernel modules: iTCO_wdt 00:1f.2 RAID bus controller: Intel Corporation 82801 SATA Controller [RAID mode] (rev 05) Subsystem: Dell Device 04a7 Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 42 I/O ports at f070 [size=8] I/O ports at f060 [size=4] I/O ports at f050 [size=8] I/O ports at f040 [size=4] I/O ports at f020 [size=32] Memory at f6105000 (32-bit, non-prefetchable) [size=2K] Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [70] Power Management version 3 Capabilities: [a8] SATA HBA v1.0 Capabilities: [b0] PCI Advanced Features Kernel driver in use: ahci 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) Subsystem: Dell Device 04a7 Flags: medium devsel, IRQ 5 Memory at f6104000 (64-bit, non-prefetchable) [size=256] I/O ports at f000 [size=32] Kernel modules: i2c-i801 01:00.0 VGA compatible controller: NVIDIA Corporation Device 0dc5 (rev a1) (prog-if 00 [VGA controller]) Subsystem: NVIDIA Corporation Device 085b Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at f8000000 (32-bit, non-prefetchable) [size=16M] Memory at d0000000 (64-bit, prefetchable) [size=128M] Memory at d8000000 (64-bit, prefetchable) [size=32M] I/O ports at e000 [size=128] Expansion ROM at fa000000 [disabled] [size=512K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Capabilities: [b4] Vendor Specific Information: Len=14 <?> Capabilities: [100] Virtual Channel Capabilities: [128] Power Budgeting <?> Capabilities: [600] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?> Kernel driver in use: nouveau Kernel modules: nouveau, nvidiafb 01:00.1 Audio device: NVIDIA Corporation GF106 High Definition Audio Controller (rev a1) Subsystem: NVIDIA Corporation Device 085b Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at fa080000 (32-bit, non-prefetchable) [size=16K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 02:00.0 VGA compatible controller: NVIDIA Corporation Device 0dc5 (rev a1) (prog-if 00 [VGA controller]) Subsystem: NVIDIA Corporation Device 085b Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f4000000 (32-bit, non-prefetchable) [size=32M] Memory at c0000000 (64-bit, prefetchable) [size=128M] Memory at c8000000 (64-bit, prefetchable) [size=64M] I/O ports at d000 [size=128] Expansion ROM at f6000000 [disabled] [size=512K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Capabilities: [b4] Vendor Specific Information: Len=14 <?> Capabilities: [100] Virtual Channel Capabilities: [128] Power Budgeting <?> Capabilities: [600] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?> Kernel driver in use: nouveau Kernel modules: nouveau, nvidiafb 02:00.1 Audio device: NVIDIA Corporation GF106 High Definition Audio Controller (rev a1) Subsystem: NVIDIA Corporation Device 085b Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at f6080000 (32-bit, non-prefetchable) [size=16K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 03:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30 [XHCI]) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at fa400000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable+ Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff Capabilities: [150] Latency Tolerance Reporting Kernel driver in use: xhci_hcd 04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 51 I/O ports at c000 [size=256] Memory at dc104000 (64-bit, prefetchable) [size=4K] Memory at dc100000 (64-bit, prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Endpoint, MSI 01 Capabilities: [b0] MSI-X: Enable- Count=4 Masked- Capabilities: [d0] Vital Product Data Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel Capabilities: [160] Device Serial Number 03-00-00-00-68-4c-e0-00 Kernel driver in use: r8168 Kernel modules: r8168 05:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6315 Series Firewire Controller (rev 01) (prog-if 10 [OHCI]) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at fa300000 (64-bit, non-prefetchable) [size=2K] I/O ports at b000 [size=256] Capabilities: [50] Power Management version 3 Capabilities: [80] MSI: Enable- Count=1/1 Maskable+ 64bit+ Capabilities: [98] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [130] Device Serial Number 00-10-dc-ff-ff-cf-56-1a Kernel driver in use: firewire_ohci Kernel modules: firewire-ohci 06:00.0 SATA controller: JMicron Technology Corp. JMB362 SATA Controller (rev 10) (prog-if 01 [AHCI 1.0]) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 19 I/O ports at a040 [size=8] I/O ports at a030 [size=4] I/O ports at a020 [size=8] I/O ports at a010 [size=4] I/O ports at a000 [size=16] Memory at fa210000 (32-bit, non-prefetchable) [size=512] Capabilities: [8c] Power Management version 3 Capabilities: [50] Express Legacy Endpoint, MSI 00 Kernel driver in use: ahci Note that my wireless card is not showing, I have the Ralink 3390 card (which apparently does not show up on Ubuntu for some reason), however I am able to connect to wireless network and connect to the internet (when it is working)

    Read the article

  • C-panel mail goes into spam instead of inbox in gmail

    - by Robin Jain
    I have c-panel vps server. I have created a domain on the same server, but when I send mail through webmail to gmail email id it goes into the spam folder. Note--->Mail ip note blacklisted Spf records enable DKIM enable reverse dns are perfect ====================================================================== Email header Information: Delivered-To: [email protected] Received: by 10.143.93.13 with SMTP id v13csp119806wfl; Fri, 6 Jul 2012 08:01:36 -0700 (PDT) Received: by 10.182.52.42 with SMTP id q10mr26133912obo.46.1341586895571; Fri, 06 Jul 2012 08:01:35 -0700 (PDT) Return-Path: <[email protected]> Received: from lakshyacs-u.securehostdns.com ([50.97.147.134]) by mx.google.com with ESMTPS id fx3si18028369obc.144.2012.07.06.08.01.35 (version=TLSv1/SSLv3 cipher=OTHER); Fri, 06 Jul 2012 08:01:35 -0700 (PDT) Received-SPF: pass (google.com: domain of [email protected] designates 50.97.147.134 as permitted sender) client-ip=50.97.147.134; Authentication-Results: mx.google.com; spf=pass (google.com: domain of [email protected] designates 50.97.147.134 as permitted sender) [email protected] Received: from localhost.localdomain ([127.0.0.1]:39016 helo=harishjoshico.com) by lakshyacs-u.securehostdns.com with esmtpa (Exim 4.77) (envelope-from <[email protected]>) id 1SnA2J-0006Nq-05 for [email protected]; Fri, 06 Jul 2012 20:31:35 +0530 Received: from 223.189.14.213 ([223.189.14.213]) (SquirrelMail authenticated user [email protected]) by harishjoshico.com with HTTP; Fri, 6 Jul 2012 20:31:35 +0530 Message-ID: <[email protected]> Date: Fri, 6 Jul 2012 20:31:35 +0530 Subject: ggglkhl From: [email protected] To: [email protected] User-Agent: SquirrelMail/1.4.22 MIME-Version: 1.0 Content-Type: text/plain;charset=iso-8859-1 Content-Transfer-Encoding: 8bit X-Priority: 3 (Normal) Importance: Normal X-AntiAbuse: This header was added to track abuse, please include it with any abuse report X-AntiAbuse: Primary Hostname - lakshyacs-u.securehostdns.com X-AntiAbuse: Original Domain - gmail.com X-AntiAbuse: Originator/Caller UID/GID - [47 12] / [47 12] X-AntiAbuse: Sender Address Domain - harishjoshico.com jhkhl ================================================================

    Read the article

  • In c-panel mail goes in spam instead of inbox in gmail

    - by Robin Jain
    I have c-panel vps server I have create a domain in the same server but when I sent a mail through webmail to gmail email id it goes into spam. Note--->Mail ip note blacklisted Spf records enable DKIM enable reverse dns are perfect ====================================================================== Email header Information: Delivered-To: [email protected] Received: by 10.143.93.13 with SMTP id v13csp119806wfl; Fri, 6 Jul 2012 08:01:36 -0700 (PDT) Received: by 10.182.52.42 with SMTP id q10mr26133912obo.46.1341586895571; Fri, 06 Jul 2012 08:01:35 -0700 (PDT) Return-Path: <[email protected]> Received: from lakshyacs-u.securehostdns.com ([50.97.147.134]) by mx.google.com with ESMTPS id fx3si18028369obc.144.2012.07.06.08.01.35 (version=TLSv1/SSLv3 cipher=OTHER); Fri, 06 Jul 2012 08:01:35 -0700 (PDT) Received-SPF: pass (google.com: domain of [email protected] designates 50.97.147.134 as permitted sender) client-ip=50.97.147.134; Authentication-Results: mx.google.com; spf=pass (google.com: domain of [email protected] designates 50.97.147.134 as permitted sender) [email protected] Received: from localhost.localdomain ([127.0.0.1]:39016 helo=harishjoshico.com) by lakshyacs-u.securehostdns.com with esmtpa (Exim 4.77) (envelope-from <[email protected]>) id 1SnA2J-0006Nq-05 for [email protected]; Fri, 06 Jul 2012 20:31:35 +0530 Received: from 223.189.14.213 ([223.189.14.213]) (SquirrelMail authenticated user [email protected]) by harishjoshico.com with HTTP; Fri, 6 Jul 2012 20:31:35 +0530 Message-ID: <[email protected]> Date: Fri, 6 Jul 2012 20:31:35 +0530 Subject: ggglkhl From: [email protected] To: [email protected] User-Agent: SquirrelMail/1.4.22 MIME-Version: 1.0 Content-Type: text/plain;charset=iso-8859-1 Content-Transfer-Encoding: 8bit X-Priority: 3 (Normal) Importance: Normal X-AntiAbuse: This header was added to track abuse, please include it with any abuse report X-AntiAbuse: Primary Hostname - lakshyacs-u.securehostdns.com X-AntiAbuse: Original Domain - gmail.com X-AntiAbuse: Originator/Caller UID/GID - [47 12] / [47 12] X-AntiAbuse: Sender Address Domain - harishjoshico.com jhkhl ================================================================

    Read the article

  • Determine All SQL Server Table Sizes

    Im doing some work to migrate and optimize a large-ish (40GB) SQL Server database at the moment.  Moving such a database between data centers over the Internet is not without its challenges.  In my case, virtually all of the size of the database is the result of one table, which has over 200M rows of data.  To determine the size of this table on disk, you can run the sp_TableSize stored procedure, like so: EXEC sp_spaceused lq_ActivityLog This results in the following: Of course this is only showing one table if you have a lot of tables and need to know which ones are taking up the most space, it would be nice if you could run a query to list all of the tables, perhaps ordered by the space theyre taking up.  Thanks to Mitchel Sellers (and Gregg Starks CURSOR template) and a tiny bit of my own edits, now you can!  Create the stored procedure below and call it to see a listing of all user tables in your database, ordered by their reserved space. -- Lists Space Used for all user tablesCREATE PROCEDURE GetAllTableSizesASDECLARE @TableName VARCHAR(100)DECLARE tableCursor CURSOR FORWARD_ONLYFOR select [name]from dbo.sysobjects where OBJECTPROPERTY(id, N'IsUserTable') = 1FOR READ ONLYCREATE TABLE #TempTable( tableName varchar(100), numberofRows varchar(100), reservedSize varchar(50), dataSize varchar(50), indexSize varchar(50), unusedSize varchar(50))OPEN tableCursorWHILE (1=1)BEGIN FETCH NEXT FROM tableCursor INTO @TableName IF(@@FETCH_STATUS<>0) BREAK; INSERT #TempTable EXEC sp_spaceused @TableNameENDCLOSE tableCursorDEALLOCATE tableCursorUPDATE #TempTableSET reservedSize = REPLACE(reservedSize, ' KB', '')SELECT tableName 'Table Name',numberofRows 'Total Rows',reservedSize 'Reserved KB',dataSize 'Data Size',indexSize 'Index Size',unusedSize 'Unused Size'FROM #TempTableORDER BY CONVERT(bigint,reservedSize) DESCDROP TABLE #TempTableGO Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

    Read the article

  • Unity3D - Android pause screen - double click issue

    - by user3666251
    I made a pause script for the game im developing for android. I added the script to the GUITexture I created and placed on the top right side of the screen.The issue stands at the part where if the player clicks the pause button then clicks resume then he wants to pause the game again.When he clicks pause the second time the buttons dont show up unless he clicks again. This is the script : #pragma strict var paused = false; var isButtonVisible : boolean = true; function OnMouseDown(){ this.paused = !this.paused; Time.timeScale = 0; isButtonVisible = true; } function OnGUI(){ if ( isButtonVisible ) { if(this.paused){ if (GUI.Button(Rect(Screen.width/2-100,Screen.height/2+3,200,50),"Restart")){ Application.LoadLevel(Application.loadedLevel); Time.timeScale = 1; isButtonVisible = false; } if (GUI.Button(Rect(Screen.width/2-100,Screen.height/2-50,200,50),"Resume")){ Time.timeScale = 1; isButtonVisible = false; } // Insert the rest of the pause menu logic if (GUI.Button(Rect(Screen.width/2-100,Screen.height/2+56,200,50),"Main Menu")){ Application.LoadLevel ("MainMenu"); isButtonVisible = false; Time.timeScale = 1; } } } } Thank you.

    Read the article

  • Creating a backup - Rsync - Connection refused (111)

    - by pablofiumara
    I am trying to create a backup of my website for free. I just want to have a backup of my website, including not only all files and the configuration but also the databases. I mean, a full backup. If it can be done automatically, it would be better. I feel there are better ways than using the cpanel to achieve that (actually, I believe sometimes web hosters does not have any cpanel). I read the following on how to do it: Automatically mirror the entire contents and configuration of your main server to a secondary backup server on a completely separate network in a different data centre. Use RSync, FXP, cPanel voodoo, or whatever method you wish to automate syncing. That is why I installed Rsync Daemon which is an alternative to SSH for remote backups. I configured it but the test went wrong. The terminal is showing me this: pablofiumara@pablofiumara-Lenovo-G470:~$ sudo rsync [email protected]::share [sudo] password for pablofiumara: rsync: failed to connect to pablofiumara.com (50.87.147.75): Connection refused (111) rsync error: error in socket IO (code 10) at clientserver.c(122) [Receiver=3.0.9] pablofiumara@pablofiumara-Lenovo-G470:~$ sudo rsync [email protected]::share failed to connect to 50.87.147.7 (50.87.147.7): Connection refused (111) rsync error: error in socket IO (code 10) at clientserver.c(122) [Receiver=3.0.9] What should I do? Is there a better or easier way to achieve what I wish (I mentioned this in the first paragraph)?

    Read the article

  • Trouble with SAT style vector projection in C#/XNA

    - by ssb
    Simply put I'm having a hard time working out how to work with XNA's Vector2 types while maintaining spatial considerations. I'm working with separating axis theorem and trying to project vectors onto an arbitrary axis to check if those projections overlap, but the severe lack of XNA-specific help online combined with pseudo code everywhere that omits key parts of the algorithm, googling has left me little help. I'm aware of HOW to project a vector, but the way that I know of doing it involves the two vectors starting from the same point. Particularly here: http://www.metanetsoftware.com/technique/tutorialA.html So let's say I have a simple rectangle, and I store each of its corners in a list of Vector2s. How would I go about projecting that onto an arbitrary axis? The crux of my problem is that taking the dot product of say, a vector2 of (1, 0) and a vector2 of (50, 50) won't get me the dot product I'm looking for.. or will it? Because that (50, 50) won't be the vector of the polygon's vertex but from whatever XNA calculates. It's getting the calculation from the right starting point that's throwing me off. I'm sorry if this is unclear, but my brain is fried from trying to think about this. I need a better understanding of how XNA calculates Vector2s as actual vectors and not just as random points.

    Read the article

  • Android From Local DB (DAO) to Server sync (JSON) - Design issue

    - by Taiko
    I sync data between my local DB and a Server. I'm looking for the cleanest way to modelise all of this. I have a com.something.db package That contains a Data Helper and couple of DAO classes that represents objects stored in the db (I didn't write that part) com.something.db --public DataHelper --public Employee @DatabaseField e.g. "name" will be an actual column name in the DB -name @DatabaseField -salary etc... (all in all 50 fields) I have a com.something.sync package That contains all the implementation detail on how to send data to the server. It boils down to a ConnectionManager that is fed by different classes that implements a 'Request' interface com.something.sync --public interface ConnectionManager --package ConnectionManagerImpl --public interface Request --package LoginRequest --package GetEmployeesRequest My issue is, at some point in the sync process, I have to JSONise and de-JSONise my data (E.g. the Employee class). But I really don't feel like having the same Employee class be responsible for both his JSONisation and his actual representation inside the local database. It really doesn't feel right, because I carefully decoupled the rest, I am only stuck on this JSON thing. What should I do ? Should I write 3 Employee classes ? EmployeeDB @DatabaseField e.g. "name" will be an actual column name in the DB -name @DatabaseField -salary -etc... 50 fields EmployeeInterface -getName -getSalary -etc... 50 fields EmployeeJSON -JSON_KEY_NAME = "name" The JSON key happens to be the same as the table name, but it isn't requirement -name -JSON_KEY_SALARY = "salary" -salary -etc... 50 fields It feels like a lot of duplicates. Is there a common pattern I can use there ?

    Read the article

  • One monitor getting spilled over into other monitor: how to do a 100% reset of gnome graphics configuration

    - by Paul Nathan
    I had to kill a VMWare process and afterwards, my monitor's configuration is buggy. I have 2 monitors in a side-by-side configuration. My right-hand monitor is the secondary monitor. Upon its right-hand side there are about 50 pixels showing from the left side of the lefthand monitor (ie, as if it was wrapped around). Further, my mouse clicks are registering as about 50 pixels sideways from where they should be. It's as if those 50 pixels between monitors got gobbled. What have I done? I've reset the screen configuration in multiple ways, using xrandr, multiple monitors app, etc. This persists in different side-by-side configurations, and also persists with another user. It does not occur with XFCE. Resetting the Window manager with the Compiz reset WM app does not fix this. I've concluded the burn-to-the-ground approach is likely the best, and would like to do a 100% reset of my graphics settings. It's an Intel integrated chipset. Removing ~/.config/monitors.xml did not work. Also, interestingly, the mouse can mouse-over the 50 errant pixels on the rhs of the right-hand monitor. I hypothesize that it's a compositing problem occurring at the layer where the background, selection, and clicks are caught. Also, inverting the right-hand monitor removes the issue, but renders the screen unusable. Even more datapoints: This happens in KDE as well Sometimes logging into Gnome and running xrandr --output DVI1 --auto resets it, but the issue immediately reappears when I press alt-tab. With Compiz Application Switch turned on, the workspace is 'pushed back' a bit, and the slice on the RHS follows it as well. I'm wondering if it's a flaw in the compiz workspace compositing configuration. I suspect the error was in the compositing configuration. I installed 11.10.

    Read the article

  • Name of the Countdown Numbers round problem - and algorithmic solutions?

    - by Dai
    For the non-Brits in the audience, there's a segment of a daytime game-show where contestants have a set of 6 numbers and a randomly generated target number. They have to reach the target number using any (but not necessarily all) of the 6 numbers using only arithmetic operators. All calculations must result in positive integers. An example: Youtube: Countdown - The Most Extraordinary Numbers Game Ever? A detailed description is given on Wikipedia: Countdown (Game Show) For example: The contentant selects 6 numbers - two large (possibilities include 25, 50, 75, 100) and four small (numbers 1 .. 10, each included twice in the pool). The numbers picked are 75, 50, 2, 3, 8, 7 are given with a target number of 812. One attempt is (75 + 50 - 8) * 7 - (3 * 2) = 813 (This scores 7 points for a solution within 5 of the target) An exact answer would be (50 + 8) * 7 * 2 = 812 (This would have scored 10 points exactly matching the target). Obviously this problem has existed before the advent of TV, but the Wikipedia article doesn't give it a name. I've also saw this game at a primary school I attended where the game was called "Crypto" as an inter-class competition - but searching for it now reveals nothing. I took part in it a few times and my dad wrote an Excel spreadsheet that attempted to brute-force the problem, I don't remember how it worked (only that it didn't work, what with Excel's 65535 row limit), but surely there must be an algorithmic solution for the problem. Maybe there's a solution that works the way human cognition does (e.g. in-parallel to find numbers 'close enough', then taking candidates and performing 'smaller' operations).

    Read the article

  • Replacing GTileLayer in Google Maps v3, with ImageMapType, Tile bounding box?

    - by justdev
    I need to update this code: radar_layer.getTileUrl=function(tile,zoom) { var llp = new GPoint(tile.x*256,(tile.y+1)*256); var urp = new GPoint((tile.x+1)*256,tile.y*256); var ll = G_NORMAL_MAP.getProjection().fromPixelToLatLng(llp,zoom); var ur = G_NORMAL_MAP.getProjection().fromPixelToLatLng(urp,zoom); var dt = new Date(); var nowtime = dt.getTime(); var tileurl = "http://demo.remoteservice.com/cgi-bin/serve.cgi?"; tileurl+="bbox="+ll.lng()+","+ll.lat()+","+ur.lng()+","+ur.lat(); tileurl+="&width=256&height=256&reaspect=false&cachetime="+nowtime; return tileurl; }; I got as far as: var DemoLayer = new google.maps.ImageMapType({ getTileUrl: function(coord, zoom) { var llp = new google.maps.Point(coord.x*256,(coord.y+1)*256); var urp = new google.maps.Point((coord.x+1)*256,coord.y*256); var ll = googleMap.getProjection().fromPointToLatLng(llp); var ur = googleMap.getProjection().fromPointToLatLng(urp); var dt = new Date(); var nowtime = dt.getTime(); var tileurl = "http://demo.remoteservice.com/cgi-bin/serve.cgi?"; tileurl+="bbox="+ll.lng()+","+ll.lat()+","+ur.lng()+","+ur.lat(); tileurl+="&width=256&height=256&reaspect=false&cachetime="+nowtime; return tileurl; }, tileSize: new google.maps.Size(256, 256), opacity:1.0, isPng: true }); Specifically, I need help with this section: var llp = new google.maps.Point(coord.x*256,(coord.y+1)*256); var urp = new google.maps.Point((coord.x+1)*256,coord.y*256); var ll = googleMap.getProjection().fromPointToLatLng(llp); var ur = googleMap.getProjection().fromPointToLatLng(urp); The service wants the tile bounding box from what I understand. However, ll and ur do not seem to correct at all. I had it working and displaying the entire map bounding box in each tile, but of course that's not what I need. Any insight here would be greatly appreciated, not having the GTileLayers in V3 is fine if I can work around it, until then I'm frustrated.

    Read the article

  • Firefox throwing a exception with HTML Canvas putImageData

    - by mr.doob
    So I was working on this little javascript experiment and I needed a widget to track the FPS of it. I ported a widget I've been using with Actionscript 3 to Javascript and it seems to be working fine with Chrome/Safari but on Firefox is throwing an exception. This is the experiment: Depth of Field This is the error: [Exception... "An invalid or illegal string was specified" code: "12" nsresult: "0x8053000c (NS_ERROR_DOM_SYNTAX_ERR)" location: "http://mrdoob.com/projects/chromeexperiments/depth_of_field__debug/js/net/hires/debug/Stats.js Line: 105"] The line that is complaning about is this one: graph.putImageData(graphData, 1, 0, 0, 0, 69, 50); Which is a crappy code to "scroll" the bitmap pixels. The idea is that I only draw a few pixels on the left of the bitmap and then on the next frame I copy the whole bitmap and paste it on pixel to the right. This error usually is thrown because you're pasting a bitmap bigger than the source and it's going off the limits, but in theory that shouldn't be the case as I'm defining 69 as the width of the rectangle to paste (being the bitmap 70px wide). And this is full code: var Stats = { baseFps: null, timer: null, timerStart: null, timerLast: null, fps: null, ms: null, container: null, fpsText: null, msText: null, memText: null, memMaxText: null, graph: null, graphData: null, init: function(userfps) { baseFps = userfps; timer = 0; timerStart = new Date() - 0; timerLast = 0; fps = 0; ms = 0; container = document.createElement("div"); container.style.fontFamily = 'Arial'; container.style.fontSize = '10px'; container.style.backgroundColor = '#000033'; container.style.width = '70px'; container.style.paddingTop = '2px'; fpsText = document.createElement("div"); fpsText.style.color = '#ffff00'; fpsText.style.marginLeft = '3px'; fpsText.style.marginBottom = '-3px'; fpsText.innerHTML = "FPS:"; container.appendChild(fpsText); msText = document.createElement("div"); msText.style.color = '#00ff00'; msText.style.marginLeft = '3px'; msText.style.marginBottom = '-3px'; msText.innerHTML = "MS:"; container.appendChild(msText); memText = document.createElement("div"); memText.style.color = '#00ffff'; memText.style.marginLeft = '3px'; memText.style.marginBottom = '-3px'; memText.innerHTML = "MEM:"; container.appendChild(memText); memMaxText = document.createElement("div"); memMaxText.style.color = '#ff0070'; memMaxText.style.marginLeft = '3px'; memMaxText.style.marginBottom = '3px'; memMaxText.innerHTML = "MAX:"; container.appendChild(memMaxText); var canvas = document.createElement("canvas"); canvas.width = 70; canvas.height = 50; container.appendChild(canvas); graph = canvas.getContext("2d"); graph.fillStyle = '#000033'; graph.fillRect(0, 0, canvas.width, canvas.height ); graphData = graph.getImageData(0, 0, canvas.width, canvas.height); setInterval(this.update, 1000/baseFps); return container; }, update: function() { timer = new Date() - timerStart; if ((timer - 1000) > timerLast) { fpsText.innerHTML = "FPS: " + fps + " / " + baseFps; timerLast = timer; graph.putImageData(graphData, 1, 0, 0, 0, 69, 50); graph.fillRect(0,0,1,50); graphData = graph.getImageData(0, 0, 70, 50); var index = ( Math.floor(Math.min(50, (fps / baseFps) * 50)) * 280 /* 70 * 4 */ ); graphData.data[index] = graphData.data[index + 1] = 256; index = ( Math.floor(Math.min(50, 50 - (timer - ms) * .5)) * 280 /* 70 * 4 */ ); graphData.data[index + 1] = 256; graph.putImageData (graphData, 0, 0); fps = 0; } ++fps; msText.innerHTML = "MS: " + (timer - ms); ms = timer; } } Any ideas? Thanks in advance.

    Read the article

< Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >