Search Results

Search found 26742 results on 1070 pages for 'linux kernel'.

Page 231/1070 | < Previous Page | 227 228 229 230 231 232 233 234 235 236 237 238  | Next Page >

• Limiting Sybase ASE 15 CPU usage on VM

  - by reiniero

  I've set up a single CPU Sybase ASE 15.7 test/hobby/experimentation system on a Debian Squeeze x64 KVM VM. I notice the CPU load goes to 100% and stays there. Definitely not a Sybase guru, only interested to see if some programs I'm running work on the database. Looking at Sybase docs it seems ASE detects the machine is idle and then takes over all processing just waiting for a connection (and if needed, doing some housekeeping apparently). Normally that would be fine but as it is running in a VM it's taking away processor resources other VMs could use - and the increased fan noise of the PC near my desk annoy me. I've tried to remedy this: set the "runnable process search count" parameter from DEFAULT (2000 IRC) to 3 in /opt/sybase/ASE-15_0/SYBASE.cfg from http://sybase.reygrobellet.com/tutorials/install_sybase_vb/standalone04_configure_oralin11#TOC-Configure-kernel I added this to my /etc/init.d/sybase startup script: echo 0 /proc/sys/kernel/randomize_va_space (though I don't think it'll make much difference) How can I tell Sybase to "behave" and not hog the processor - I don't mind reduced performance.

  Read the article

• OpenAFS on Fedora/CentOS

  - by Michael Pliskin

  I am trying to see if OpenAFS fits my needs as a distributed filesystem and is a bit stuck. There are docs but they're all quite hard to understand, so asking for some expert advice here. My questions: which version to install? I need windows client support so I need 1.5 - right? But it is not stable.. Or is it? And don't see any pre-built rpms for it, so compiling from sources? tried to compile and it worked but it created a non-"mp" kernel module while my kernel needs an mp one - how to workaround that? do I really need a new fresh partition to start with or I can re-use an existing one and just make it available via afp? any nice HOWTOs around?

  Read the article

• What can I do to give some more love and disk space to my database on Ubuntu?

  - by Yaron Naveh

  I'm new to linux. I've deployed a db to ubuntu server on amazon and found out I'm low on disk space. did df (see below) - and found out that I'm 89% capacity on one file system, but less on others. What does this mean? Do I have a few partitions and can now utilize others besides /dev/xvda1? Also /dev/xvdb seems large, is it safe to put the db in it and only use it? If so do I need to mount it or do something special? $> df -lah Filesystem Size Used Avail Use% Mounted on /dev/xvda1 8.0G 6.7G 914M 89% / proc 0 0 0 - /proc sysfs 0 0 0 - /sys none 0 0 0 - /sys/fs/fuse/connections none 0 0 0 - /sys/kernel/debug none 0 0 0 - /sys/kernel/security udev 3.7G 8.0K 3.7G 1% /dev devpts 0 0 0 - /dev/pts tmpfs 1.5G 164K 1.5G 1% /run none 5.0M 0 5.0M 0% /run/lock none 3.7G 0 3.7G 0% /run/shm /dev/xvdb 414G 199M 393G 1% /mnt

  Read the article

• OpenAFS on Fedora/CentOS

  - by Michael Pliskin

  I am trying to see if OpenAFS fits my needs as a distributed filesystem and is a bit stuck. There are docs but they're all quite hard to understand, so asking for some expert advice here. My questions: which version to install? I need windows client support so I need 1.5 - right? But it is not stable.. Or is it? And don't see any pre-built rpms for it, so compiling from sources? tried to compile and it worked but it created a non-"mp" kernel module while my kernel needs an mp one - how to workaround that? do I really need a new fresh partition to start with or I can re-use an existing one and just make it available via afp? any nice HOWTOs around?

  Read the article

• Can not boot CentOS VM using VirtIO in KVM

  - by Jake

  I converted qcow2 image to raw and changed I/O bus to VirtIO for a VM. now I can't boot that VM. I Installed VirtIO driver with following command: mkinitrd --with virtio_pci --with virtio_blk -f /boot/initrd-$(uname -r).img $(uname -r) and these are related kernel modules: virtio_balloon 11329 0 virtio_blk 11593 3 virtio_pci 11845 0 virtio_ring 8513 1 virtio_pci virtio 9541 3 virtio_balloon,virtio_blk,virtio_pci and this is what happens during boot-up. I also changed /boot/grub/device.map from "(hd0) /dev/sda" to "(hd0) /dev/vda" but problem still exists. any ideas how to fix this ? This is my default option to boot: title CentOS (2.6.18-308.13.1.el5) root (hd0,0) kernel /vmlinuz-2.6.18-308.13.1.el5 ro root=/dev/VolGroup00/LogVol00 initrd /initrd-2.6.18-308.13.1.el5.img

  Read the article

• Dualbooting Win7 and Gentoo, error

  - by Tommy Jakobsen

  Hello I'm trying to setup a dualboot with Gentoo Linux and Windows 7. Heres my partitions: /dev/sda1 /boot partition, ext2 /dev/sda2 win7 partition, ntfs /dev/sda3 swap partition, linux swap /dev/sda4 root partition, btrfs Using Grub, I can boot into Gentoo, but when I'm choosing to boot Windows 7, nothing happens. It just writes the Grub options for that choice, and then it hangs. grub.conf: default 0 timeout 30 title Gentoo root (hd0,0) kernel /boot/kernel-x86_64-2.6.31 root=/dev/sda4 title Windows rootnoverify (hd0,1) makeactive chainloader +1 Any ideas? Help will be much appreciated!

  Read the article

• information about /proc/pid/sched

  - by redeye

  Not sure this is the right place for this question, but here goes: I'm trying to make some sense of the /proc/pid/sched and /proc/pid/task/tid/sched files for a highly threaded server process, however I was not able to find a good explanation of how to interpret this file ( just a few bits here: http://knol.google.com/k/linux-performance-tuning-and-measurement# ) . I assume this entry in procfs is related to newer versions of the kernel that run with the CFS scheduler? CentOS distro running on a 2.6.24.7-149.el5rt kernel version with preempt rt patch. Any thoughts?

  Read the article

• SSH broken, segfault error 4

  - by trampi

  i cannot connect to my server via ssh, it throws me a "server unexpectedly closed connection" after entering the password. in var/log/messages the only noteable message is: Apr 14 17:41:23 s15410270 kernel: sshd[3602]: segfault at c0 ip 7f0801acbdb0 sp 7fff0adff860 error 4 in libc-2.8.so[7f0801a87000+14f000] Apr 14 17:41:29 s15410270 kernel: sshd[3606]: segfault at c0 ip 7f75f9463db0 sp 7fff027971f0 error 4 in libc-2.8.so[7f75f941f000+14f000] This message appears after a log in attempt via ssh or via sftp Its a SuSE Linux server. I'm looking for help where to start to search for the error, i can still act as root via a serial console. edit: "server unexpectedly closed connection" only appears if i enter the correct password!

  Read the article

• Ubuntu 9.04 Cannot Connect to visible open wifi ap (reason 6)

  - by Andrew Bolster

  I'm travelling currently so the last network i connected successfully to was my home wpa-psk network. I hadn't tried anything until i got to my accommodation that is an open network (that I'm on now on the Win7 partition on my laptop). The network (and a similar archetypical 'linksys' open network, aswell as some protected local networks are correctly displayed in network-manager and upon selection, it happily spins around to its hearts content for a while before saying 'no chance boy'. /var/log/syslog spills out the usual combination of wpa_supplicant and kernel messages, the most interesting of are that the kernel deauthentication reason 6 response. 6 apparently means class2FrameFromNonAuthStation...Client attempted to transfer data before it was authenticated. Anyone seen anything like this? I've already tried going closer to the router to no avail. I don't remember seeing this any other time I've connected to a open AP, even if that AP is far away. (Signal strength for this AP is good, kismet says its around -57dBm, well above the threshold of -80dBm, and I've tried all the suggestions from the 'Related Questions'

  Read the article

• How to use UMLFS?

  - by Vi

  I'm trying to mount what is inside UML session as FUSE filesystem on host. There's "uml_mount" program which looks like a thing for this purpose, but it fails. What is UMLFS (I haven't found any documentation at all) and how to mount it? uml_mount mounts FUSE filesystem and starts uml_mconsole <umid> umlfs <file descriptor> which tries to send this file descriptor to UML kernel (to deal with further FUSE things), but sending fails. Also I haven't found any signs of FUSE inside a kernel. Do I need some special patch for this?

  Read the article

• kill SIGABRT does not generate core file from daemon started from crontab.

  - by Guma

  I am running CentOS 5.5 and working on server application that sometimes I need to force core dump so I can see what is going on. If I start my server from shell and send kill SIGABRT, a core file is created. If I start same program from crontab and then I send the same signal to it the server is "killed" but no core file is generated. Does any one know why is that and what need to be added to my code or changed in system settings to allow core file generation? Just a side note I have ulimit set to unlimited in /etc/profile I have set kernel.core_uses_pid = 1 kernel.core_pattern=/var/cores/%h-%e-%p.core in /etc/sysctl.conf Also my server app was added to crontab under same login id as I am running it from shell. Any help greatly appreciated

  Read the article

• How do I use memmap to reserve memory on boot?

  - by alexl

  Ive got a laptop with some corrupted ram addresses, so I'm trying to use memmap to reserve them before linux boots up. Ive been trying to use memmap=10M$1024M' as a kernel boot option, but linux crashes (with no errors) and restarts. If I use a different syntax for memmap likememmap=1023M@0M` it boots fine. Do I have to specify a certain size block to reserve or could my kernel version not support reserving memory with memmap? Maybe I'm better off using memmap=exactmap, and if so, could somebody point me to a good faq on how to use it?

  Read the article

• information about /proc/pid/sched

  - by redeye

  Not sure this is the right place for this question, but here goes: I'm trying to make some sense of the /proc/pid/sched and /proc/pid/task/tid/sched files for a highly threaded server process, however I was not able to find a good explanation of how to interpret this file ( just a few bits here: http://knol.google.com/k/linux-performance-tuning-and-measurement# ) . I assume this entry in procfs is related to newer versions of the kernel that run with the CFS scheduler? CentOS distro running on a 2.6.24.7-149.el5rt kernel version with preempt rt patch. Any thoughts?

  Read the article

• eTrayz: Replace base system with a bootstrapped Debian

  - by knoopx

  I bought an eTrayz NAS time ago. The device is more or less good but it ships with a closed-source custom linux and a bunch of broken web-apps. I wanted to replace the whole system with a raw Debian installation. I successfully bootstrapped a Lenny Debian into a chroot and I'm able to use use it. However I would like it to be the default system and to boot automatically at login. The device itself ships with a bundled 2.6.24.4 kernel. I think the kernel is on a dedicated flash memory so I would prefere not to re-flash it. What do you think is the best way to accomplish it?

  Read the article

• Can a named (bind) crash make a server unreachable?

  - by giorgio79

  My server recently became unreachable, and after restart a named error was the last line I found in /var/log/messages before restart: Jun 26 00:15:06 host named[1303]: error (network unreachable) resolving 'dlv.isc.org/DNSKEY/IN': 2001:500:71::29#53 Jun 26 06:38:55 host kernel: imklog 5.8.10, log source = /proc/kmsg started. Jun 26 06:38:55 host rsyslogd: [origin software="rsyslogd" swVersion="5.8.10" x-pid="1294" x-info="http://www.rsyslog.com"] start Jun 26 06:38:55 host kernel: Initializing cgroup subsys cpuset Can a named crash make a server unreachable? I doubt it, as I assume I should still be able to login with ssh via IP, but the server did not respond...So, I am trying to make heavy guesses here.

  Read the article

• Lost Page Write I/O Errors on CentOS LVM setup

  - by Gregg Leventhal

  I have a CentOS 6 box with LVM setup and one of the PVs is a USB disk (I know). One of them is getting the error: Oct 30 10:57:07 alpha01 kernel: lost page write due to I/O error on dm-3 Oct 30 10:57:07 alpha01 kernel: Buffer I/O error on device dm-3, logical block 4 Which is causing problems with all of the LVs on it. pvs shows the PV as unknown device. I can ls to the logical volumes and they show up in lvdisplay, but first I get a bunch of IO errors. I made sure the cables are secure between the USB drive. What should I do to get this back up and running for the meanwhile? Should I unmount each LV and run an fsck.ext4 on each one like fsck.ext4 -y /dev/vg1/lv_logvolname ?

  Read the article

• Tracing out going connections

  - by Tiffany Walker

  Jan 24 07:00:49 HOST kernel: [875997.380464] Firewall: *TCP_OUT Blocked* IN= OUT=eth0 SRC=108.60.11.15 DST=74.80.225.32 LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=18789 DF PROTO=TCP SPT=64823 DPT=81 WINDOW=14600 RES=0x00 SYN URGP=0 Jan 24 07:00:50 HOST kernel: [875998.378321] Firewall: *TCP_OUT Blocked* IN= OUT=eth0 SRC=108.60.11.15 DST=74.80.225.32 LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=18790 DF PROTO=TCP SPT=64823 DPT=81 WINDOW=14600 RES=0x00 SYN URGP=0 I run fcgid so everything runs as a user. But is there a way to trace and figure out who is running an out going script? The sites all share the same IP so it's hard to know which site it is or where the script is located at.

  Read the article

• Deactivate GPU and use IGP

  - by squelos

  I am having some trouble with my Sony Vaio SVE1511W1e laptop. It has an ATI Radeon and the i5 has an IGP (i5 2450m). I don't often use my GPU, and the IGP would be just enough for most usage I do. Therefore, in order to improve the battery life, I wish to deactivate the GPU and use only the IGP. The problem is that my BIOS doesnt allow me to do so. But I believe it is possible to deactivate the GPU 'programatically'. I'm running Debian Wheezy on the 3.2.0.4 AMD64 kernel. The first problem I'm running into is that when I run lspci, my IGP doesnt show up. Could this be because im lacking a kernel module? (I chose a targeted installation). What are the solutions to deactivating a GPU and using an IGP on a Linux System such as debian?

  Read the article

• QNAP (469L) with Debian: can't connect to router

  - by agtoever

  I've been running my QNAP 469L with Debian (Wheezy deb7u3) for a few months. Yesterday I upgraded the memory to 4 GB. The system boots fine, but since the upgrade, I'm not able to connect the server to my router (a TP-Link WR941ND). My configuration: The router runs a DHCP server (192.168.67.100 and up), with a preconfigured ip address for the QNAP (192.168.67.10). The router is on 192.168.67.1. As said, Debian is installed on the QNAP (which can be regarded as a normal computer). Networking hardware on the QNAP: Intel PRO/1000 Network Connection using the e1000e kernel module. This is what I have tried so far: Replace the network cable (tried 3 different cables on different router ports). Check for messages from the kernel: dmesg | grep eth. Besides the normal hardware messages I get a ADDRCONF(NETDEV_UP): eth0: link is not ready for each call to ifup. Manually restart the network sudo server networking restart Check sudo ifconfig (eth0 is up, but no ip addresses). Check the /etc/network/interfaces which has (besides the loopback device) an allow-hotplug eth0 and iface eth0 inet dhcp, which is afaik the default Debian configuration. Since the server has two ethernet ports, I checked if I'm using the right port (checked the hardware address that ifconfig reports for eth0 is the same as the hardware address that is in the preconfigured ip address for the server in the router. Do a manual sudo ifdown eth0 && sudo ifup eth0 with no results (but an extra ADDRCONF(NETDEV_UP): eth0: link is not ready in the kernel log) Do a dhcp request dhclient -v eth0: for about a minute requests are send (according to the terminal) and at the end I get a No DHCPOFFERS received. No working leases in persistent database - sleeping.. Check the router system log if DHCP requests are received. I see them for some devices (my Mac, my iPhone) but not from the QNAP. The log entry looks like: DHCPS:Recv REQUEST from 84:85:06:07:75:6A and then a DHCPS:Send ACK to 192.168.67.101. There are no records from the QNAP's hardware address. So the two error messages that I do get are: ADDRCONF(NETDEV_UP): eth0: link is not ready for every ifup and No DHCPOFFERS received. No working leases in persistent database - sleeping. for every DHCP call.

  Read the article

• What package(s) to exclude to not upgrade from RHEL 5.3 to 5.5?

  - by yan bellavance

  I know how to exclude certain packages when updating RHEL like: yum update --exclude=kernel How would I prevent yum from updating from 5.3 to 5.5

  Read the article

• I suspect that my HDD is causing hardlocks, as all other components have been replaced. How can I check this theory and solve the potential cause?

  - by user867814

  I have had this problem over quite a while now, thorough multiple Linux kernel versions and distributions, as well as replacement of all components, aside from my main HDD - RAM, GPU(twice), mother board, CPU, power supply. What happens is, at one point during the operation of the PC, it will hardlock - everything stops working, external HDD is not shut down correctly and continues to spin until I plug it out and in, there are no system/kernel logs of any kind, and no otherwise nothing that would suggest a cause. Another reason for my suspicion is that the failures happen almost exclusively during HDD read/write activity - shutdown(happens nearly 1/3 of the time so far, it's only been few days though), launching programs, and once during operation of apt. I hope the post is descriptive enough, if you need any additional info, ask(and tell me how to prepare/obtain it), and I will provide. If I'm wrong, point me in the right direction. Thanks in advance.

  Read the article

• Is there good FAT driver for FUSE? (Lightweight, not mountlo)

  - by Vi.

  FUSE filesystem list show some FuseFat and FatFuse. Both are old, FatFuse is read-only , FuseFat is non-buildable and probably depends on glib. Now I'm using mountlo for the task (mounting USB drives in generic way without root access or suid things (except of fusermount itself)), but it looks too big for such task. Using FUSE to mount external storage devices is good both for security and for flexibility reason: the kernel sees only block reads and writes while actual code that deals with filesystem details runs with user privileges, allowing user to use custom filesystems and preventing from kernel filesystem exploits. Is there good vfat FUSE driver?

  Read the article

• Trouble getting OS fingerprinting to work in iptables

  - by user1197457

  Everyone, As I understand it, OSF has been merged with the Kernel since 2.6.before-my-kernel-version. Yet when I do something like this: iptables -I INPUT -j ACCEPT -p tcp -m osf --genre Linux --log 0 --ttl 2 and I get an error like: iptables: No chain/target/match by that name iptables -L Shows no rules because I did an iptables -F at one point. ALSO, the following command: cat /proc/net/ip_tables_matches Does not show "osf" on the list. A google doesn't seem to help. I've also installed iptables-devel in hopes I'd be able to load the osf module. Sadly I haven't been able to get that to work. Centos 6.4 minimal Any guidance?

  Read the article

• Microphone not capturing sound on 12.04 Lenovo G580

  - by Yam Marcovic

  In both Skype and the Sound Recorder application, I am not capturing any audio from my built-in microphone. I'm not sure why. Otherwise, sound output is working well. I have tried running gstreamer-properties and setting the Default Input plugin to PulseAUdio as well (to match the output), and it didn't help. I have tried running alsamixer -V all and I only get 2 input-related entries: Capture(L R) which is on 100 and not muted (can't be either), and Analog Mic Boost which is on 20db. Extra info: Camera (video) is working well on Skype and Kamerka. Can you please help me get my microphone to work? lspci: 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) Subsystem: Lenovo Device 3977 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) (prog-if 00 [VGA controller]) Subsystem: Lenovo Device 3977 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 42 Region 0: Memory at e0000000 (64-bit, non-prefetchable) [size=4M] Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M] Region 4: I/O ports at 3000 [size=64] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: i915 Kernel modules: i915 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) (prog-if 30 [XHCI]) Subsystem: Lenovo Device 3977 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 41 Region 0: Memory at e0600000 (64-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: xhci_hcd 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) Subsystem: Lenovo Device 3977 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 43 Region 0: Memory at e0614000 (64-bit, non-prefetchable) [size=16] Capabilities: <access denied> Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) (prog-if 20 [EHCI]) Subsystem: Lenovo Device 3977 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at e0619000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) Subsystem: Lenovo Device 3977 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 44 Region 0: Memory at e0610000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00002000-00002fff Memory behind bridge: e0500000-e05fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 Memory behind bridge: e0400000-e04fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) (prog-if 20 [EHCI]) Subsystem: Lenovo Device 3977 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at e0618000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) Subsystem: Lenovo Device 3977 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel modules: iTCO_wdt 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) (prog-if 01 [AHCI 1.0]) Subsystem: Lenovo Device 3977 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 40 Region 0: I/O ports at 3088 [size=8] Region 1: I/O ports at 3094 [size=4] Region 2: I/O ports at 3080 [size=8] Region 3: I/O ports at 3090 [size=4] Region 4: I/O ports at 3060 [size=32] Region 5: Memory at e0617000 (32-bit, non-prefetchable) [size=2K] Capabilities: <access denied> Kernel driver in use: ahci 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) Subsystem: Lenovo Device 3977 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 10 Region 0: Memory at e0615000 (64-bit, non-prefetchable) [size=256] Region 4: I/O ports at 3040 [size=32] Kernel modules: i2c-i801 01:00.0 Ethernet controller: Atheros Communications Inc. AR8162 Fast Ethernet (rev 08) Subsystem: Lenovo Device 3979 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at e0500000 (64-bit, non-prefetchable) [size=256K] Region 2: I/O ports at 2000 [size=128] Capabilities: <access denied> 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: Lenovo Device 31a1 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at e0400000 (64-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: ath9k Kernel modules: ath9k aplay -l **** List of PLAYBACK Hardware Devices **** card 0: PCH [HDA Intel PCH], device 0: CONEXANT Analog [CONEXANT Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0

  Read the article

• Android ANR keyDispatchingTimedOut Error while continuous tapping on screen.

  - by user519846

  Hi All, I am getting Application Not Responding (ANR) dialog while continuous tapping on the screen. There is no view on the screen where i am tapping. Frequency of this issue is less but still i am not able to remove it completely. Here i am attaching the log what i caught during this error. ERROR/ActivityManager(1322): ANR in com.test.mj.and.ui (com.test.mj.and.ui/.TermsAndCondActivity) ERROR/ActivityManager(1322): Reason: keyDispatchingTimedOut ERROR/ActivityManager(1322): Parent: com.test.mj.and.ui/.SplashActivity ERROR/ActivityManager(1322): Load: 6.59 / 6.37 / 5.21 ERROR/ActivityManager(1322): CPU usage from 11430ms to 2196ms ago: ERROR/ActivityManager(1322): rtal.mj.and.ui: 9% = 7% user + 1% kernel / faults: 649 minor ERROR/ActivityManager(1322): system_server: 4% = 2% user + 2% kernel / faults: 10 minor ERROR/ActivityManager(1322): logcat: 3% = 1% user + 1% kernel / faults: 675 minor 1 major ERROR/ActivityManager(1322): synaptics_wq: 1% = 0% user + 1% kernel ERROR/ActivityManager(1322): ami304d: 1% = 0% user + 0% kernel ERROR/ActivityManager(1322): .process.lghome: 1% = 0% user + 0% kernel / faults: 47 minor ERROR/ActivityManager(1322): sync_supers: 0% = 0% user + 0% kernel ERROR/ActivityManager(1322): droid.DunServer: 0% = 0% user + 0% kernel / faults: 6 minor ERROR/ActivityManager(1322): events/0: 0% = 0% user + 0% kernel ERROR/ActivityManager(1322): oid.inputmethod: 0% = 0% user + 0% kernel / faults: 2 minor ERROR/ActivityManager(1322): m.android.phone: 0% = 0% user + 0% kernel / faults: 2 minor ERROR/ActivityManager(1322): ndroid.settings: 0% = 0% user + 0% kernel ERROR/ActivityManager(1322): sh: 0% = 0% user + 0% kernel / faults: 110 minor ERROR/ActivityManager(1322): -flush-179:0: 0% = 0% user + 0% kernel ERROR/ActivityManager(1322): TOTAL: 19% = 13% user + 6% kernel WARN/WindowManager(1322): Continuing to wait for key to be dispatched WARN/WindowManager(1322): No window to dispatch pointer action 1 Can anyone please help me to solve this issue? Thanks in advance.

  Read the article

< Previous Page | 227 228 229 230 231 232 233 234 235 236 237 238  | Next Page >