Search Results

Search found 11766 results on 471 pages for 'info plist'.

Page 232/471 | < Previous Page | 228 229 230 231 232 233 234 235 236 237 238 239  | Next Page >

• does the *physical* order/location of drives in a mdadm-managed RAID-10 array matter?

  - by locuse

  i've setup a 4-drive RAID-10 array using mdadm-managed, software-raid on an x86_64 box. it'd up & running and works as expected, cat /proc/mdstat md127 : active raid10 sdc2[2] sdd2[3] sda2[0] sdb2[1] 1951397888 blocks super 1.2 512K chunks 2 far-copies [4/4] [UUUU] bitmap: 9/466 pages [36KB], 2048KB chunk atm the four SATA drives are physically plugged into the motherboard's 1st four SATA ports. i'd like to gather the necessary/complete info for catastrophic recovery. reading starting here, http://neil.brown.name/blog, and the mailing list, i'm not yet completely confident i have it right. i understand 'drive order matters'. is that logical, &/or physical order that matters? if i unplugged the four drives in this array, and plugged them each back into different ports on the motherboard or a pci card, as long as i've changed nothing in software config, will the array correctly auto-re-assemble?

  Read the article

• Secure copying (file transfer) between two Linux servers in the same datacenter (Linode)

  - by MountainX

  I have two Linodes in the same data center. I want to copy files from one to the other each night or on demand (for about the next month, until this project is finished). So I'm thinking about using rsync. My question is how do I set up the two Linode servers to communicate via private IP addresses securely? Both servers are SSH hardened, they use denyhosts and have a fairly restrictive iptables setup. I know I need to first assign private IP addresses to each server, then configure static networking according to this guide. What is next? What SSH or iptables settings are needed to allow these two servers to communicate? What further info do I need to supply in this question? I'm looking for a basic step-by-step guide for how to do this.

  Read the article

• understanding mount -o bind

  - by Ionut

  Few questions after the following commands: mount -o bind /new_disk/home/user/ /home/user/ mount -o bind --no-mtab /new_disk/home/user/ /home/user/ What is the difference between the two commands other than " Mount without writing in /etc/mtab. This is necessary for example when /etc is on a read-only filesystem." What is the difference between mount -o bind and mount --bind ...if there are Let's suppose i don't know there is a partition mounted using -o bind --no-mtab...where can I find if there is any mound point with bind ? The only way i can detect this is grep user /proc/mounts but in that line there is no info abut bind. Thank you.

  Read the article

• Where does the temporary flash file get stored when I am viweing from Firefox

  - by Nishant

  I am watching a lecture and it seems to be adobe flash ...I wanna save this video that I am viewing . The website I am checking is http://cs75.tv/2009/fall/ . I am using Firefox . Dont know if this info helps , but .... My about:cache result is this . Memory cache device Number of entries: 212 Maximum storage size: 13312 KiB Storage in use: 8087 KiB Inactive storage: 6819 KiB List Cache Entries Disk cache device Number of entries: 3224 Maximum storage size: 500000 KiB Storage in use: 26066 KiB Cache Directory: C:\Documents and Settings\nvarm\Local Settings\Application Data\Mozilla\Firefox\Profiles\d74svniy.default\Cache List Cache Entries Offline cache device Number of entries: 0 Maximum storage size: 512000 KiB Storage in use: 0 KiB Cache Directory: C:\Documents and Settings\nvarm\Local Settings\Application Data\Mozilla\Firefox\Profiles\d74svniy.default\OfflineCache List Cache Entries

  Read the article

• HP Pavilion dv6000 QuickPlay power on

  - by user22559

  Hello I have a question for HP Pavilion dv6000 owners. If your laptop is powered down, and you press the QuickPlay button or the DVD button (NOT the power button), does the laptop start up? More info: I am asking this because I have got a hold of a broken HP dv6000. If I power it up, the power light lights up, and then the laptop powers down. It seems to be because of a broken motherboard. But the laptop does the same thing if you press the QuickPlay or DVD buttons, and I want to know if that's supposed to happen, or if it's something else that is wrong.

  Read the article

• Cannot increase my screen resolution

  - by Patrick Beardmore

  I am trying to install my new monitor but my Graphics Adapter (Mobile Intel(R) 915GM/GMS,910GML Express Chipset Family) does not offer a resolution of 1920x1080 in the [Display Properties Settings] window. It only offers up to 1360x768. Can anyone explain to me how I can increase this number to the correct resolution. The monitor does show my the windows desktop, albeit at a lower resolution which is being stretched to fill the screen, making it look very blurry. I have installed the "Monitor Drivers" I found on the disk supplied with new monitor, but these do not appear to have made any difference. The Intel software that comes with the graphics card has an information window containing lots of info about the card and the monitor itself. I have placed this on a webpage so you can examine it if helpful. Many thanks with your help in getting my Christmas present to work! Patrick P.S.: Before I got this screen I checked to see if my graphics card could cope with such a large screen.

  Read the article

• How to tell if linux disk IO is causing excessive (> 1 second) application stalls

  - by noahz

  I have a Java application performing a large volume (hundreds of MB) of continuous output (streaming plain text) to about a dozen files a ext3 SAN filesystem. Occasionally, this application pauses for several seconds at a time. I suspect that something related to ext3 vsfs (Veritas Filesystem) functionality (and/or how it interacts with the OS) is the culprit. What steps can I take to confirm or refute this theory? I am aware of iostat and /proc/diskstats as starting points. Revised title to de-emphasize journaling and emphasize "stalls" I have done some googling and found at least one article that seems to describe behavior like I am observing: Solving the ext3 latency problem Additional Information Red Hat Enterprise Linux Server release 5.3 (Tikanga) Kernel: 2.6.18-194.32.1.el5 Primary application disk is fiber-channel SAN: lspci | grep -i fibre 14:00.0 Fibre Channel: Emulex Corporation Saturn-X: LightPulse Fibre Channel Host Adapter (rev 03) Mount info: type vxfs (rw,tmplog,largefiles,mincache=tmpcache,ioerror=mwdisable) 0 0 cat /sys/block/VxVM123456/queue/scheduler noop anticipatory [deadline] cfq

  Read the article

• XP can't read data from transferred HD

  - by Alexander Miller

  Computer A, running XP, died. XP was installed on a fresh HD in computer B. Slaved data-backup HD from A was installed as slave on B. B will not read it; shows only 2 folders, Recycler and System Volume Info. All of these are older machines with IDE drives. What's going on & how can I read/transfer the data from the transferred drive? This was only a trial run. Actually I will need to transfer the master HD from A - which has XP on it - and read from its data partition because (blush) the backup drive was not up to date.

  Read the article

• nagios: trouble using check_smtps command

  - by ethrbunny

  I'm trying to use this command to check on port 587 for my postfix server. Using nmap -P0 mail.server.com I see this: Starting Nmap 5.51 ( http://nmap.org ) at 2013-11-04 05:01 PST Nmap scan report for mail.server.com (xx.xx.xx.xx) Host is up (0.0016s latency). rDNS record for xx.xx.xx.xx: another.server.com Not shown: 990 closed ports PORT STATE SERVICE 22/tcp open ssh 25/tcp open smtp 110/tcp open pop3 111/tcp open rpcbind 143/tcp open imap 465/tcp open smtps 587/tcp open submission 993/tcp open imaps 995/tcp open pop3s 5666/tcp open nrpe So I know the relevant ports for smtps (465 or 587) are open. When I use openssl s_client -connect mail.server.com:587 -starttls smtp I get a connection with all the various SSL info. (Same for port 465). But when I try libexec/check_ssmtp -H mail.server.com -p587 I get: CRITICAL - Cannot make SSL connection. 140200102082408:error:140770FC:SSL routines:SSL23_GET_SERVER_HELLO:unknown protocol:s23_clnt.c:699: What am I doing wrong?

  Read the article

• How to completely remove MySQL from Windows?

  - by Nathan Long

  (I realize there are similarly-titled questions, but this one is really 'how do I reset the password', and this one doesn't specify an OS and has only gotten Linux-oriented answers.) On Windows XP, I just uninstalled MySQL and deleted the folder that it was installed in. I then rebooted and reinstalled MySQL. When it comes back up, it still has the databases it had before the uninstall. Where did it keep that database info? How do I completely remove MySQL and start over, as if I'd never installed it?

  Read the article

• How can I create a pen drive that I can boot from, and then install Win98 from?

  - by rossmcm

  I have a HP Compaq t5515 thin client computer with a flash disk and USB port. I want to put Win98 onto it, replacing whatever is on there now (I think it is some Linux-based thing). I can find stuff about putting Win98 onto a pen drive and running from that, but I can't find any info about installing Windows 98 from a pen drive onto a sep[arate system. Is it just a matter of making the pen drive bootable to DOS copying the contents of a Win98 installation CD onto the pen drive booting the HP machine from the pen drive running SETUP.EXE from the pen drive? Any pointers appreciated. TIA

  Read the article

• Font Book does not Install all Fonts

  - by waiwai933

  My Mac decided to delete all but 19 fonts, which is fairly annoying. It didn't really delete them, as in I still have the original files in the /Library/Fonts folder, but they've disappeared from Font Book, so I can't use them. Now, Apple says that you can select a folder to install all fonts in that folder, but when I try that, the spinning wheel (not the beach ball) comes up in the lower right hand corner for a few seconds and then leaves, without installing any fonts. The same thing happens if I use the + sign in the menu bar, select multiple, or if I try validating and then installing (actually, that installs one font). Is there any way to mass-install these fonts or will I have to install them one by one? Comp info: Mac OS X 10.5.8 running Font Book 2.1 (123).

  Read the article

• Unable to diagnose Windows 7 lockup

  - by Delyan

  Basic info: Laptop Dell Studio XPS 13 (Intel P9600, 4GB RAM, NVidia 9400M card, 256G Samsung PM800 SSD) Windows 7 Ultimate, as well as Fedora 14 Here's the deal - Windows would just lock up out of nowhere, no log entries, no dumps, no BSOD, it just freezes. This happens mostly when idle (but it happened when I was using it too) and does not follow a concrete time frame. No input is accepted - only solution is to hold the power button. Although this sounds like a clean cut hardware issue, the reason I'm willing to rule this out is that my primary OS is Fedora 14. It's been working fine for the past 2 years and I've been stress testing the hardware (intentionally or not) every once in a while with no issues. I would like to ask if there's any way to get a diagnostic output from Windows in a situation such as this. The next step in my testing is to leave it in Safe Mode overnight and see if it locks up but even if I do that, I still need to figure out what component freezes it up during normal operation.

  Read the article

• Webmin apache on CentOS 6.3 results in 403 forbidden, permissions are OK

  - by Mario De Schaepmeester

  First of all, I will mention that the permissions are fine for the document root directory, which is /webapps/nimbus/www/public_html The www directory contains a PHP application. PHP is a problem for later if it doesn't work, as I've tested it with a plain html file (does not work either) I just get 403 forbidden responses. The permissions are 755 on webapps and all subdirectories. I've checked other questions here and on the internet, but it was all about those permissions. Whatever info you still need, just ask, I don't know what's relevant as it's the first time ever I'm using webmin or configuring apache.

  Read the article

• New video card? [closed]

  - by TutorialPoint

  I ran into some problems with my ATI Radeon x1200. I want it to support vertex shader 3.0, but it only does 2.0. This is because Call of Duty: Modern Warfare 2 only works with 3.0. So, I want a new video card. Can someone help me, with a more clean look to it? I bet if I would stick to some seller, I would end up with a video card that does not support what I want, or is too expansive. I really do not want it to be above $75, if possible. Some info about my PC: Manufacter: XXODD Processor: AMD Athlon64 X2 DualCore 4000+ 2Ghz (but running currently 32 bit OS) ATI Radeon X1200 video card (the problem) 1 GB RAM DDR2 MS-7367 Motherboard Windows 7 Ultimate OS 32-Bit Build 7600 RTM

  Read the article

• What is the command to use to put your computer to sleep (not hibernate)?

  - by airrick

  I want to put my windows pc (win7) into a sleep state via command line (so i can bind to macro button on keyboard). The power button on the PC is setup to but the computer to sleep (but it's down on the floor and I'm too lazy to reach down) it exactly how I want it (sleeps using hybrid mode in case I loose power) The sleep command on the shutdown menu also works. most info I found says to use; %windir%\system32\rundll32.exe PowrProf.dll, SetSuspendState 0,1,0 But this puts the computer in hibernate mode. I do have hibernate disabled but using hybrid sleep. So, What is the command to use to put your computer to sleep (not hibernate)?

  Read the article

• reg delete gives me "access is denied" but regedit delete is ok

  - by Radek

  I need to delete a key from a command line. So I wanted to use reg delete "the key to be deleted" /f but I get ERROR: access is denied. From the same login session (the same user) I am able to delete the key without any troubles from regedit.exe that is not run as administrator. I cannot use runas command to execute reg that I believe would be to solution because in fact I want to use reg to delete registry entry for administrator profile so runas works again. More info in my other question Windows7 corrupted profile - prevention exists?

  Read the article

• TV network capabilities.

  - by Narcolapser

  Question: Can the major TV producer's internet TV systems access network resource? Info: I'm looking for large TV's right now for my company to set up in conference rooms. We want the ability to load presentations with out having to have a computer to do so. Our hope is to put things on to network drives and access and display them from there. I've heard that LG's can do this if you convert the power point file in to a show format. that's fine. I just need to get this information to the TV with out the computer attached. Can anyone tell me if companies like LG, Vizio, Sony, Samsung, etc. have TV's that are capable of doing this? Thanks ~n

  Read the article

• Slow Internet connection

  - by Muthu Kumaran P

  My internet connectivity from my Laptop slowed down overnight. I have no clue as what had happened. I was able to download at 300kbps the day before yesterday. And from yesterday on, my internet has been slow. My download speed is at 25kbps. Can someone help me to resolve this issue? I am using wireless connection on my Sony Vaio. I am not sure what else info I need to give as this is my first time to post a question here..

  Read the article

• How to understand cpu family/model/stepping fields in /proc/cpuinfo

  - by Victor Sorokin

  I have following in cpuinfo: processor : 0 vendor_id : AuthenticAMD cpu family : 15 model : 107 model name : AMD Athlon(tm) 64 X2 Dual Core Processor 5600+ stepping : 2 According to Wikipedia page there are two kinds of 5600+ -- one of 90nm technology, another of 65nm. How can I understand which one I have? There seem to be no direct correspondence between contents of cpuinfo and info on Wikipedia page. AMD site seems to use some other naming scheme for processors too. How can I map values of family, model and stepping from cpuinfo to the data available on Wikipedia/AMD?

  Read the article

• Can I completely convert an Ubuntu desktop installation to a server one? (not just the packages)

  - by Rey Leonard Amorato

  I am aware that the server and desktop editions only differ by the packages installed, and I can install server packages (LAMP etc.) into a desktop edition and get the same thing. However, I want to be able to completely change my desktop installation into a server edition. e.g: when I type uname -a or lsb_release -a it is supposed to say Ubuntu server or something. I currently have an 11.10 desktop installation with LAMP stack installed and the info displayed by apache is "Apache blah blah, on (Ubuntu) server. Where does apache get this information that I am using an Ubuntu desktop installation and not a server one? Is there a config file(s) to edit?

  Read the article

• PHP does not allow https connections

  - by FunkyChicken

  Hey guys im running PHP 5.4.0 and I cannot cURL nor files_get_content() https connections. Using curl in a PHP script shows: [root@ns1]# /opt/php/bin/php -q test.php * About to connect() to www.google.com port 443 * Trying 74.125.225.210... * connected * Connected to www.google.com (74.125.225.210) port 443 * successfully set certificate verify locations: * CAfile: /etc/pki/tls/certs/ca-bundle.crt CApath: none Segmentation fault Using file_get_contents() shows: Warning: file_get_contents(): Unable to find the wrapper "https" - did you forget to enable it when you configured PHP? in /test.php OpenSSL and OpenSSL-devel are installed, and PHP is also configured with cURL support for SSL connections. See: http://i.imgur.com/ExAIf.png Any idea what might be going wrong? Further info: CentOS 5.8(64) with Nginx 1.2.4

  Read the article

• Brightness too dark or too bright

  - by YatharthROCK

  Basically, below a seemingly-arbitrary threshold (seems to be around 60%) my laptop screen is too dark to really make out much, and above that threshold it takes its maximum brightness (which is waay too bright for my eyes). This problem only occurs when I change the brightness using Windows' UI. Changing the brightness using Fn keys on my keyboard works as expected; unless the screen went into dark mode because of Windows, in which case they have no effect. This problem started occuring on my ASUS laptop very recently. My laptop has a poor battery, but I don't think that's related. What is going on? I tried resetting power plan settings, turning off adaptive brightness and restarting. I'll give any info asked for. Help required urgently...

  Read the article

• OpenVPN Permission Denied Error

  - by LordCover

  I am setting OpenVPN up, and I'm in the state of adding users. Details: Host System: Windows Server 2003 32-bit. Guest System: Ubuntu Linux (with OpenVPN installed already), actually I downloaded it from OpenVPN.Net. Virtualization: VMWare v7.0 Problem: I can access the Access Server web portal (on the port 5480), but when I login to http://host_ip:943/admin and enter my (correct) login info, it shows me a page saying that "You don't have enough permissions". I am the (root) user!!!! that is really weird!!! Note: if I enter wrong login it will denote an incorrect login, this means that I am logging in successfully but the problem comes after the login process. What I tried: I tried to create another user after (root) logging in to Linux Bash using (useradd) command, but the same resulted.

  Read the article

• Streamline Active Directory account creation via automated web site

  - by SteveM82

  In my company we have high employee turnover, and hence our helpdesk receives about a dozen requests per week for new Active Directory accounts. Currently, we receive these requests simply via e-mail or voice-mail, and rarely do we have all of the information necessary to create the account. I would like to find a web application that can be used by a manager or supervisor to formalize the requests they make for AD accounts for new employees under their command. Ideally, the application would prompt for all of necessary information, and allow the helpdesk to review the requests and approve or deny each one. If approved, the application would take care of creating the account and send an e-mail to the manager. I have found several application on the Internet that handle self-service account management (i.e., password resets or update contact info), which is also nice to have, but nothing that streamlines the new account request and creation part. Can anyone make suggestions on such an application? Thanks.

  Read the article

< Previous Page | 228 229 230 231 232 233 234 235 236 237 238 239  | Next Page >