Search Results

Search found 7618 results on 305 pages for 'named graph'.

Page 233/305 | < Previous Page | 229 230 231 232 233 234 235 236 237 238 239 240  | Next Page >

• How to reinstall bootloader after migration to SSD

  - by hijarian

  I must say, it was difficult to name this question. Basically, I need to properly reinstall the bootloader on my system, because I already have the working system disks for my OSes. The long story is this: I had the large slow HDD with Windows7 & Debian Wheezy dual-boot on it, perfectly bootable. Then, I ordered the SSD drive and prepared my system partitions to fit onto the much smaller SSD. I wanted the following schema: 128 GB Windows 24 GB / on Debian 86 GB /home on Debian Strange size for /home because there's no such thing as true 256GB disk drive. So, I've prepared such a partitions on my initial HDD and installed the new SSD and then I loaded the GParted live USB (can't remember now how it was really named), and then just copypasted the partitions from HDD to SSD. So, now I have the following partitions across the physical disks: SSD 128 GB copy of original Windows partition 24 GB copy of presumably Debian / 86 GB copy of presumably Debian /home HDD 128 GB Windows 24 GB / on Debian 86 GB /home on Debian ... several other partitions with non-system data ... And the behavior of the system right after the Ctrl+C, Ctrl+V in GParted was as follows: no GRUB, system boots right into the Windows on HDD. In BIOS settings are to boot from SSD first. I managed to create the Debian Testing installation USB and loaded it into the rescue mode, found that it identified my SSD as /dev/sda and installed the GRUB to the /dev/sda. Now my system loads the GRUB which lists both Windows and Debian. From HDD. So, I am now back into initial position. Please, how I should set up the GRUB so it'll load the OSes correctly from SSD? Should I fire up my Debian, fiddle with the GRUB's config and reinstall it again to the same place (at SSD)?

  Read the article

• need to bring back win 7

  - by user290513

  I like making music and playing games and occasionally do some Photoshop. I had a windows 8 computer but my mouse pointer always got stuck, so to try out something new I installed Ubuntu. here is how I installed it: Went to advanced statup options clicked on "use a device" after plugging in my bootable USB with Ubuntu replaced my windows 8 and installed Ubuntu 14.04 LTS I hope I did it correctly though. So after a few months I could've really find out a good Audio Production (not LMMS, because I use Stagelight) software nor something that could be familiar to the UI of Photoshop. So I decided to bring back Windows, but because of the bad experience of 8 I thought about bringing back win 7 So I used an app named WinUSB to make my bootable USB drive after formatting it to NTFS in GParted But when I go to my grub menu, my USB doesn't show up and my PC being a UEFI device. I don't know how to get to the bios of my device. Can somebody tell how to install Windows 7 completely and deleting Ubuntu or at least give me a link to a tutorial. I have a netbook: it is an Acer Aspire One 725. I'm fine with using commands in terminal and another thing that my laptop doesn't have a CD drive or reader, I can't put a CD inside

  Read the article

• Dosbox USB print Windows 8.1 64Bit

  - by eCronik

  Worked fine until I've upgraded to Windows 8.1 as well as made the mail programm working (had to get a windows live ID and have to type in a password now, when starting Windows). I did set the USB printer to lpt1 on the local Windows 8 computer and another XP computer via LAN to lpt2 the same way with the same printer on the Windows 8 computer. But now it doesn't work anymore from the Win8 one (where the printer is plugged via USB). Tried already deleting lpt2: on the XP one, as well as lpt1 on the Windows 8, resetted it. Not working... :-( I tried also net use lpt1: \server\printer password "\user:Ute Berger" /persistent:yes of course with the correct server and shared printer name as well as net use \server\printer "\user:Ute Berger" password /persistent:yes . This is the name displayed as a user now. But in C:\users it is named Benutzer1. Tried this one also. Nothing worked. What could be the problem here? What's strange is that when I type "net use lpt1:" on the XP, I get another error (67 - The networkname wasn't found) than trying something I didn't set up like lpt2 (2 - The system can't find the file). Could this be a possible problem as even if deleted something is left blocking on the Windows 8 computer? Please help me - I tried for hours today but all I've got was frustration... Regards Tim

  Read the article

• .htaccess issue on Apache Web Server in Ubuntu VM

  - by Neon Flash

  I just installed Apache Web Server on Ubuntu 11.04 in VMWare Workstation. I created a basic HTML page, named it index.html and placed it in /var/www directory (document root). I am able to access this web page from my Host OS (Windows 7), by pointing the browser to: http://192.168.2.2/index.html where, 192.168.2.2 is the IP Address of the Ubuntu VM. Next, to test various configurations of .htaccess files, I created a new directory in /var/www called, members. Inside this directory, I created and placed a .htaccess file with the following configuration: AuthUserFile /www/Neon/auth/.htpasswd AuthName "neon's home" AuthType Basic require valid-user IndexIgnore */* I created a directory path like /var/www/Neon/auth/ and then placed a .htpasswd file inside it. To place the username and hash inside the .htpasswd file: I created a username "neon" and calculated the DES hash of a password and placed it inside .htpasswd file in format: username:hash Now, when I try to access the web page: http://192.168.2.2/members/ It does not prompt me to enter the username and password with a popup box. Instead it just displays the index.html which is placed inside members directory. I would like to get this configuration working :)

  Read the article

• IIS7.5 - about app pool ID's and folder read/write access

  - by merk

  I did some searching and it looks like for each app pool, there should be an account created called IIS APPPOOL\AppPoolName - however i can see no such account when i try to modify the permissions on a folder to give that app write access. The closest I have found is the IIS_IUSRS group. Now, if i go into that group and look at the members, i see several IIS APPPOOL\PoolName members. But where are these members coming from? Why don't they show up under the users? And why can't i add a specific one to a folder? It doesn't make sense to me to add the IIS_IUSRS group to a folder since they gives every site access to the folder. To be more specific, I'm setting up wordpress and it unfortunately wants write access to the root folder. So i want to restrict it as much a possible. I was trying to figure out how to set it so that the WP root folder has write access only for the ID that the blog's app pool is running under. When i drill down into the IIS_IUSRS group, i do not see the app pool for the blog listed there. The settings for the blog's app pool are: No managed code, Classic, ApplicationPoolIdentity, and it's named 'blog' So any explanations regarding these users that are created for the app pools, and why the blog doesn't seem to belong to the iusrs group? thanks

  Read the article

• unicorn and nginx, went wrong

  - by achempion

  I try to deploy my app via capistrano. It was done, but when I start to nginx and show my site in the browser I see 'We're sorry, but something went wrong.' It is bad. I use unicorn. See my configs https://gist.github.com/3904032 I try to start server via rails s -e prodiction and it's work! I think that this error may be because I can't restart server root@li272-194:~# /etc/init.d/nginx restart Restarting nginx: the configuration file /etc/nginx/nginx.conf syntax is ok configuration file /etc/nginx/nginx.conf test is successful [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: still could not bind() nginx. any ideas? nginx log 2012/10/17 02:57:41 [error] 3271#0: *1 could not find named location "@myapp", client: 91.192.62.77, server: 178.79.153.194, request: "GET / HTTP/1.1", host: "178.79.153.194" 2012/10/17 02:19:08 [crit] 2448#0: *8 connect() to unix:/srv/zarcon/shared/unicorn.sock failed (2: No such file or directory) while connecting to upstream, client: 91.192.62.77, server: zarkon, request: "GET / HTTP/1.1", upstream: "http://unix:/srv/zarcon/shared/unicorn.sock:/", host: "178.79.153.194"

  Read the article

• BIND: forward 1st level zone

  - by raven

  First of all: sorry for the language, English is not my primary language. I have star-like DNS structure with many filials (more that 2): ^ | v filialNS_1.filial_1.city.local <---- ns.main.city.local <---- filialNS_2.filial_2.city.local ^ | v ns.mail.city.local is slave of all filials zones filialNS_1 is master of filial_1.city.local filialNS_2 is master of filial_2.city.local filialNS_N is master of filial_N.city.local I want to: serve DNS queries for xxx.filial_N.city.local with filialNS_N.filial_N.city.local forward all queries for xxx.xxx.xxx.local from filialNS_N to ns.main.city.local forward other queries to our provider's DNS on filial (or google-public-dns or anything else) FILIAL CONFIG named.conf zone "filial_1.city.local" { type master; file "/etc/namedb/dynamic/filial_1.city.local"; allow-update { key DHCP_UPDATER; }; allow-transfer { <ns.main.city.local IP address> }; }; zone "2.76.10.in-addr.arpa" { type master; file "/etc/namedb/dynamic/2.76.10.in-addr.arpa"; allow-update { key DHCP_UPDATER; }; allow-transfer { <ns.main.city.local IP address> }; }; zone "local." { type forward; forward only; forwarders { <ns.main.city.local IP address> }; }; nslookup server.filial_1.city.local - works fine nslookup server.main.city.local Server: 127.0.0.1 Address: 127.0.0.1#53 ** server can't find server.main.city.local: NXDOMAIN Where am I going wrong?

  Read the article

• Setup ejabberd with SQL Server 2008

  - by wonster

  Here's what I have got so far. Windows 2008 Server 64 bit. Installed the latest version of ejabberd, ejabberd-2.1.8-windows-installer.exe. The windows service starts up fine but seems ineffective. However, using the start & stop scripts work. I am able to login to the admin page which so far doesn't seem that versatile. Opened up ports 5222, 5226 and 5280 for my workstation to talk to the server. I've got Spark and Jabbear Windows clients to register, login and instant message with multiple accounts using the server. After confirming that I've got the very basics working, I've decided to make use of SQL Server 2008 as the database. Reason? Mainly, I am very comfortable with SQL Server. I can deal with redundancy, failover, data analysis easily. Not sure if ejabberd's built in DB provides all that. Following the instructions from ejabberd's documentation, I setup a system DSN that points to another physical database. The DSN checks out fine. (Tried both Named Pipes and TCP/IP) Modified ejabberd.cfg. Commented line %%{auth_method, internal} and uncommented line {auth_method, odbc} Uncommented and modified {odbc_server, "DSN=ejabberd;UID=somelogin;PWD=somepassword"}. After making these changes, I restarted. No errors are found in the log files. The jabber clients are no longer able to register new accounts. I'm not sure where to look for errors besides the /logs/ folder as I'm new to all this. I am basically stuck here on step 5. Has anyone got this setup to work recently? Some of the posts I've found around are years old and of no help. I can't be the only one setting up ejabberd with MS SQL. Any help would be appreciated!

  Read the article

• SQL - an error occurred during the pre-login handshake

  - by Rivka

  Until yesterday evening, I was able to connect to my server from my local machine. Now, I get the following error: A connection was successfully established with the server, but then an error occurred during the pre-login handshake. (provider: SSL Provider, error: 0 - The wait operation timed out.) (.Net SqlClient Data Provider) Note, I can log on to the actual server with no problem. Yesterday, I installed IIS on my machine and set up a site using my IP address - don't know if this has anything to do. I did come across this article, followed the steps, but didn't seem to help. http://www.escapekeys.com/blog/index.cfm/2011/1/26/Microsoft-SQL-Server-Error-64-A-connection-was-successfully-established-with-the-server I also went through the following article, changed TC/IP settings, restarted, but nothing. http://blog.sqlauthority.com/2009/05/21/sql-server-fix-error-provider-named-pipes-provider-error-40-could-not-open-a-connection-to-sql-server-microsoft-sql-server-error/ Started trying suggestions from comments too but stopped when I realized I might be messing things up more. So, why is this happening / how can I fix?

  Read the article

• User profile service fails

  - by s.r.a

  I have Windows 7 and 3 drives on my HDD. The second drive is D:\, and there are some files in that. I decided to install 8.1 Enterprise so I installed it in dual boot manner beside 7 and in D:\ drive which as I said was not empty and when installing 8.1, I didn't format the D:. I installed 8.1 successfully in D:\ and it was working fine. One time which I came up with 7, I thought I should arrange the 8.1 folders in D: to be separated from the other non-8.1 folders, so I created a new folder named it "Windows 8.1" and cut all 8.1 folders and pasted them into that new folder. Now my D: drive was arranged. When I restart the PC, I selected the 8.1 to start with, but it didn't come up like before and instead, it shows now a blue screen (not the blue screen of death!) and the time is shown in left-down corner of it. When I click the screen this message appears: The User Profile Service service Failed the sign-in. User Profile can not be loaded. I know two things: 1- The problem is to do with that cutting and pasting the 8.1 folders to be arranged. And 2- If I reinstall the 8.1, the problem will be solved (but if I don't do that cutting and pasting again!) Is there any simpler way to solve the issue and have the two OSs with each other?

  Read the article

• can't register a soft phone to asterisk11

  - by Tom

  I have a VM (on oracle vbox) running Fedora17. I've installed asterisk 11 on it from sources. I've followed the wiki for installation (https://wiki.asterisk.org/wiki/display/AST/Creating+SIP+Accounts) to the letter. The ip on the VM machine running fedora is 192.168.1.7 and I can ping it from the host machine (Ubuntu 12.04), which is at 192.168.1.2 I've tried registering with ekiga with the following settings: user: [email protected]. Password: verysecretpassword registar: 192.168.1.7 but I'm getting an error "transport fail". Also, while trying to register I'm logged in to the asterisk CLI with verbose level 3 and debug level 4 and nothing appears. some more relevant data: I've added the following code to the end of my sip.conf.sample file: [demo-alice] type=friend host=dynamic secret=verysecretpassword context=users deny=0.0.0.0/0 permit=192.168.1.0/255.255.255.0 [demo-bob] type=friend host=dynamic secret=othersecretpassword context=users deny=0.0.0.0/0 permit=192.168.1.0/255.255.255.0 After I changed the sip.conf.sample file, I've created a copy of it and named it sip.conf. then I logged in to the asterisk CLI and typed sip reload. Then I'm trying to register and ekiga client from my host machine at 192.168.1.2 but it doesn't work and nothing appears on the asterisk CLI while in verbose mode level 3. BTW, If there is missing information about my question, please don't close it. comment about what you need to know and I'll edit it in to the question. tnx.

  Read the article

• How do I send e-mails with attachments to a Microsoft WebTV user?

  - by Petr 'PePa' Pavel

  my friend uses Microsoft WebTV (e-mail address ends with @webtv.net) and I'd like to send him an e-mail with a picture attached to it. We went through a series of attempts one of which ended up a success, all others a failure. He just can't see my e-mail in his mailbox, when it contains an attachment. E-mails without attachments always go through all right. What seemed to help in the first successful case, was that he added my e-mail address to his address book and my e-mail suddenly showed up. Seemed to have been delivered before but hidden. He kept my address in his address book however, it didn't help with the following trials. He did look into his junk folder, nothing there. I made sure the file name contains no spaces. It's a regular jpeg, named something-like-this.jpg I downsized it to have only about 50k, as I've read somewhere that that's a limit. I actually doubt this piece of information, because I think the successful attempt was larger. webtv.net contains zero information. I watched their video demo for the e-mail client, so I at least know how the user interface looks like. I've never laid my hands on the real thing. I'm an advanced user myself (a programmer) but I can't wrap my mind around this. He on the other hand, is a very technically inexperienced user and because he's half way across the globe, I can't come and look over his shoulder. He doesn't have a computer, afaik there's no way I could see what he sees. Any ideas on how to debug this? Thanks for your time, guys. P.S. I can't tag this "webtv" because such tag doesn't exist yet and my reputation is too low, sorry.

  Read the article

• How do i play nicely with MS SQL/SQL Server 2008

  - by acidzombie24

  Big problem. I have nearly given up. I am trying to port my prototype to use MS SQL so it will work on a server once i get it (the server will be SQL Server 2008, shared, i dont know any more info). So i tried to connect to SQL Server via visual studios IDE and had no luck. I enabled TCP and named pipes and restarted the service (and computer) with still no luck. I remembered about mdf files so i made that after an obstacle of not being able to make the connect string require i figure out visual studio has it in its properties and successfully connected with that. Then i had a problem with nested transactions. After not being able to figure out how to check i wondered if i can configure it to allow it somehow. I always thought all of MS were the same except for limitations but sql server seems to support nested transactions so theres no point trying to work around the problem with .mdf files since i wont need them and really just used it to port the base of my sql code and to check if syntax is correct. I tried installing SQL Server Management Studio since people mentioned it several times (as a solution or at least help). When installing it on windows 7 it says it may not be compatible. After running it, it launched SQL Server Installation Center (64-bit) which doesnt seem to be the same thing as i dont see a way to modify any of my server (networking) configurations or edit user permissions, etc. I am clueless what to do next. Does anyone have any ideas? I'm posting here bc i think my problem is more configurations and sql server then programming.

  Read the article

• Windows Share permissions

  - by Armando

  I have a SQL/File server that I am replicating a File Share and SQL instance, using ArcServer RHA, to a Replica server. Everything seems to work as far as the replication of the SLQ instance and Share is concerned. When I fail over to the Replica server the DNS Host A record is modified to point to the Replica Server IP Address so if I do an NSLOOKUP on ServerA it then points to the IP Address of ServerB. Ans since the SQL instance is named the same I can still map my ODBC connections to ServerA and I can still make a SQL connection. When I try to do a \ServerA\Share I get an error that says I do not have permissions to the Share. I think this is because it uses keberose authentication and the Share is tied to the actual sever host name. I have tried puting in a CNAME and pointing it to ServerA and Disabling Strict Name Checking on ServerB as well as adding the CNAME to the OptionalNames in the registry but I am still getting the error when I have the ServerA powered off. Is there a way to reset the Authentication of the Share to use the DNS Cname?

  Read the article

• Serving static content with Apache web server and Tomcat

  - by Hunter

  I've configured Apache web server and Tomcat like this: I created a new file in apache2/sites-available, named it "myDomain" with this content: <VirtualHost *:80> ServerAdmin [email protected] ServerName myDomain.com ServerAlias www.myDomain.com ProxyPass / ajp://localhost:8009 <Proxy *> AllowOverride AuthConfig Order allow,deny Allow from all Options -Indexes </Proxy> </VirtualHost> Enabled mod_proxy and myDomain a2enmod proxy_ajp a2ensite myDomain Edited Tomcat's server.xml (inside the Engine tag) <Host name="myDomain.com" appBase="webapps/myApp"> <Context path="" docBase="."/> </Host> <Host name="www.myDomain.com" appBase="webapps/myApp"> <Context path="" docBase="."/> </Host> This works great. But I don't like to put static files (html, images, videos etc.) into {tomcat home}/webapps/myApp's subfolders instead I'd like to put them the apache webserver's root WWW directory's subdirectories. And I'd like Apache web server to serve these files alone. How could I do this? So all incoming request will be forwarded to Tomcat except those that ask for a static file.

  Read the article

• Can't Connect SQL server - process being used by another process. Conflict with IIS?

  - by shinya

  I'm having problem connecting to MS SQL Server (2012 Express) after accessing a database through IIS (web site). I can access the data through web site no problem, but I can't access the data from any other programs (i.e SSMS) until I reboot the SQL server. It seems that the connection stays open even if I close a browser. Here is error message I'm getting Unable to open the physical file "C:---------". Operating system error 32: "32(The process cannot access the file because it is being used by another process.)". Unable to open the physical file "C:-------". Operating system error 32: "32(The process cannot access the file because it is being used by another process.)". Cannot open user default database. Login failed. Login failed for user 'Myserver\myname'. (.Net SqlClient Data Provider) Server Name: MYPC\SQLEXPRESS Error Number: 5120 Severity: 16 State: 101 Line Number: 65536 I follow the help link and it told me to move TCP before named pipes in the protocol order list. I tried it but it didn't help at all. What is the proper settings on SQL server or IIS in order to release process after closing a browser. How do I avoid getting this error? Thank you for your help

  Read the article

• Can you see something wrong in my .htaccess?

  - by AlexV

  OK, after many search, trial and errors I've managed to create an .htaccess that do what I wanted (see explanations and questions after the code block): <IfModule mod_rewrite.c> RewriteEngine On #1 If the requested file is not url-mapper.php (to avoid .htaccess loop) RewriteCond %{REQUEST_FILENAME} (?<!url-mapper\.php)$ #2 If the requested URI does not end with an extension OR if the URI ends with .php* RewriteCond %{REQUEST_URI} !\.(.*) [OR] RewriteCond %{REQUEST_URI} \.php.*$ [NC] #3 If the requested URI is not in an excluded location RewriteCond %{REQUEST_URI} !^/seo-urls\/(excluded1|excluded2)(/.*)?$ #Then serve the URI via the mapper RewriteRule .* /seo-urls/url-mapper.php?uri=%{REQUEST_URI} [L,QSA] </IfModule> This is what the .htaccess should do: #1 is checking that the file requested is not url-mapper.php (to avoid infinite redirect loops). This file will always be at the root of the domain. #2 the .htaccess must only catch URLs that don't end with an extension (www.foo.com -- catch | www.foo.com/catch-me -- catch | www.foo.com/dont-catch.me -- don't catch) and URLs ending with .php* files (.php, .php4, .php5, .php123...). #3 some directories (and childs) can be excluded from the .htaccess (in this case /seo-urls/excluded1 and /seo-urls/excluded2). Finally the .htaccess feed the mapper with an hidden GET parameter named uri containing the requested uri. Even if I tested and everything works, I want to know if what I do is correct (and if it's the "best" way to do it). I've learned a lot with this "project" but I still consider myself a beginner at .htaccess and regular expressions so I want to triple check it there before putting it in production...

  Read the article

• In Outlook 2007 Rules and Alerts, EXACTLY what does "my name" mean?

  - by Cornan The Iowan

  I can't find any definition of "my name" in the Outlook 2007 Rules and Alerts or on the Internet. In this case our email system presents two email addresses for me to the outside world. I'd like BOTH of these addresses to be recognized as being "me". I thought that perhaps if I understood the definition of "my name" in the rules, I could set up my mailbox(es) appropriately. Of course if "my name" actually means a single email address, then I won't be able to do so, but if it means "any email on my account" or "any account meeting [some criteria]", then I might be successful. I'd like to note a subtlety in the rules definitions. While there is a rule named "where my name is in the To or Cc box", the only rule for explicit addresses is "sent to people or distribution list" (I'm assuming that "sent to" means "in the To:" list rather than "in the To: or cc: lists"). Summing up. My preference: 1) Understanding the precise definition of "my name" so that I can use "where my name is in the To or Cc box" to capture both email addresses from my account. 2) Learning the "sent to people or distribution list" actually includes Cc: entries (I can test this myself of course) 3) Any other solution that will let me define a rule where my secondary email address will be detected in EITHER the To: or Cc: boxes.

  Read the article

• Whats the difference between pulling from a branch into master and pushing that branch onto master?

  - by Justin808

  In Tortoisegit, on the repository, I right-click and select sync. At the top of the dialog there are options for Local Branch and Remote Branch. If the local branch is named DeveloperA and the remote branch is master and I do a push, what happens? If the local branch is master and remote branch is DeveloperA and I Pull, what happens? If I am on the master branch and right click, select Merge and change the From to be my DeveloperA branch, what happens? If I try to push from master to remote master and the remote is updated git stops and tells me to pull. It seems if I push from DeveloperA to master it doens't stop, it just clobbers, it that correct? We're having an issue using git where the remote master branch gets clobbered at times and we are trying to figure out why. For example there is a developer working on his DeveloperA branch. He'll pull from master to get any updates, then push to master to push out his changes. But there are times that the push lists more files in the Out Commit list than he's edited. The odd thing is he can't revert those files as git is saying they are up to date and have not been modified. Yet when he pushes git pushes the files out. The problem is if there are changes between his pull and push the changes get clobbered.

  Read the article

• FTP account ownership on vhost directory makes Apache not run website correctly

  - by CodeShining

  I've purchased a virtual server, where I'm given of a non-root sudo-enabled user. Actually I do need to create an FTP account that's not that sudo-able account, so I created a no-login account just for that purpose. I've set up VSFTPd correctly, also enabling the "userlist" feature, to specify which user are permitted to use FTP. Then I created an empty directory under my sudo-able account, and I gave ownership permissions to the second account, so to make it more easy to understand, let's say the main account (the one I do use to manage my VPS) is called ubuntu and the FTP-user is named ftpuser, I created a directory /home/ubuntu/mywebsite giving the ownership to ftpuser:ftpuser. Then I uploaded a worpdress website, whose default permissions are 755 and 644. The issue is that Apache is not given of any privilege to run the website. How can I make the website run properly, and which is the most secure? Should I run that virtualhost with another user (if it's possible)? Should I force the FTP user to use the www-data group (if that's possible) and run with permissions like 775 and 664? How can I solve this issue? Any help is appreciated, I'd like to run it using the default permissions, so any update won't break up anything (because of permissions reset).

  Read the article

• Some doubts about the use of usermod and groupmod command

  - by AndreaNobili

  I am not yet a true "Linux guy" and I have the following doubts about how exactly do the following shell procedure (a list of commands steps) founded in a tutorial that I am following (I want deeply understand what I am doing before do it): sudo passwd root then login again as root usermod -l miner pi usermod -m -d /home/miner miner groupmod -n miner pi exit So at the beginning it enable the root account and I have to login again in the system as root...this is perfectly clear for me. And now I have the followings doubts: 1) The usermod command: usermod -l miner pi usermod -m -d /home/miner miner Reading the official documentation of the usermod command I understand that this command modify the informations related to an existing account Reading the documentation it seems to me that the -l parmether modify the name of the user pi in miner and then the -m -d paramether move the contents of the old home directory to the new one (named miner) and use this new directory as home directory My doubt is: what exactly do the executions of these operation? I think that: Rename the existing pi user in miner Then move the content of the old home directory (the pi home directory? or what?) into a new directory (/home/miner) that now is the home directory for the miner user. Is it right? The the second doubt is related to this command groupmod -n miner pi It seems to me that change the group name from pi in miner But what exactly is a group in Linux and why is it used? Tnx

  Read the article

• How to delete a file that contains a backslash in the name under Windows 7?

  - by espinchi

  I want to delete a file named workspaces\google-gson-1.7.1-release.zip Yep, it contains a backslash in the name. Here it is: G:\>dir Z_DRIVE Volume in drive G is samsung Volume Serial Number is 48B9-7E1D Directory of G:\Z_DRIVE 04/06/2012 08:09 PM <DIR> . 04/06/2012 08:09 PM <DIR> .. 05/01/2011 02:21 PM 528,016 workspaces\google-gson-1.7.1-release.zip 1 File(s) 528,016 bytes 2 Dir(s) 88,400,478,208 bytes free The first attempt is to just delete it from the Windows Explorer, but it says it can't find the file. Then, I tried from the command line: G:\>del Z_DRIVE\workspaces\google-gson-1.7.1-release.zip The system cannot find the file specified. And, after researching a bit in the internets, I also tried the following, with no luck: G:\>del \\?\G:\Z_DRIVE\workspaces\google-gson-1.7.1-release.zip The system cannot find the file specified. Other than booting from some Linux CD, is there a way to get rid of this file? Update: also tried the following combinations, but the error is the same: G:\>del "\\?\G:\Z_DRIVE\workspaces\google-gson-1.7.1-release.zip" G:\Z_DRIVE>del workspaces\google-gson-1.7.1-release.zip G:\Z_DRIVE>del "workspaces\google-gson-1.7.1-release.zip" G:\Z_DRIVE>del workspaces*google-gson-1.7.1-release.zip

  Read the article

• How do I use command line and wmctrl to make a window larger than the screen to get a huge screenshot?

  - by Mnebuerquo

  I use a program which makes a large image which I have to scroll to view. The program has no way to save the image, and I have no access to the source to modify it. The only way I have to get the image from the program is by screenshot. My goal is to save the full size image without having to piece together individual screenshots. I'm using this script to try taking a screenshot: #!/bin/bash window=$(wmctrl -l | grep "Program$" | awk '{print $1}') wmctrl -v -i -r $window -e '0,0,0,6030,5828' wmctrl -i -a $window import -window $window ~/Desktop/screenshot.png This uses wmctrl to get the window id ($window) for a window named "Program". It then tries to resize the window to the desired dimensions. It uses imagemagick (import) to save a screenshot.png on the user's Desktop. All of this works except the resize step. I can resize the window using wmctrl -r -e, but sizes greater than the screen size don't work. I'm using Ubuntu 10.04 and the Gnome Desktop. I run two monitors, but I've tried this with one of them disabled. Is there a way to resize the window larger than my screen to get a huge screenshot?

  Read the article

• Must have local user to authenticate Samba to AD?

  - by Phil

  I've got a CentOS 5.3 server with Samba running. I've joined this server to my domain in the hopes of allowing AD users some access to my Samba shares. I've found that this works, but only as long as the AD username that I'm trying to authenticate with is also a local user on the server. In other words, if I'm trying to access a share, and try to authenticate with the AD username "joe", I get errors unless I create a user named 'joe' on the server. I don't have to create a matching password or anything....the local user's password is always blank, so I do know that the authentication is actually happening against the AD. Here's my smb.conf file: [global] workgroup = <mydomain> server string = <snip> netbios name = HOME security = ADS realm = <mydomain.com> password server = <snip> auth methods = winbind log level = 1 log file = /var/log/samba/%m.log [amore] path = /var/www/amore browseable = yes writable = yes valid users = DOMAIN\user1 DOMAIN\user2 DOMAIN\user3 DOMAIN\user4 I would assume that my kerberos settings are fine, as I've joined the domain and can use wbinfo to see users and groups. However, I can provide that info if necessary. Anyone have any ideas?

  Read the article

• Join Domain from VM

  - by Adis

  I have two VMs running on VMWare Player. I use NAT adapter settings. The host machine for VMs is running on corporate network. First VM has Domain controller running and I can log in on that machine using domain credentials. I named domain wm.local When I run IP config on this machine: IP: 192.168.87.132 Def Gataway: 192.168.87.2 DNS server: 192.168.87.2 DHCP server: 192.168.87.254 Second VM cannot join domain. When I try it with domain WM I'm propmted for credentials. And I enter Administrator credentials and than it waits for some time and I get response: "The specified domain either does not exist or could not be contacted" If i type wm.local as domain when trying to join it does not prompt me to login but just shows "An Active Directory Domain Controller (AD DC) for the domain wm.local could not be contacted. And here it takes no time to get this error message. Ipconfig on this machine: IP: 192.168.87.134 Def Gataway: 192.168.87.2 DNS server: 192.168.87.2 DHCP server: 192.168.87.254 I can ping second VM from first one. And I disabled firewalls on both machines. Any ideas? Is there any manual for this?

  Read the article

< Previous Page | 229 230 231 232 233 234 235 236 237 238 239 240  | Next Page >