Search Results

Search found 6711 results on 269 pages for 'generic noob'.

Page 234/269 | < Previous Page | 230 231 232 233 234 235 236 237 238 239 240 241  | Next Page >

• Router reconfigures PC's and they can no longer access the internet via hardwired connection to DSL Modem

  - by zchads

  Router reconfigures PC's and they can no longer access the internet via hardwired connection to DSL Modem. Hardware Information: Buffalo Wireless Router/access point, Model: WZR-HP-G300NH-AP DSL Modem: Generic (actually not sure of manufacture). Service Provider: TOT (Thailand) Laptop-1: Windows XP and Belkin PCMIA Network Card Laptop-2: Windows XP unknown network card & Wifi Laptop-3: Windows 7 unknown network card & Wifi Outline of Problem/actions taken: After a recent power failure the router and laptop-1 connected to router were no longer able to access the internet. Actions taken to try and recover internet access: Using Laptop-1 tried to configure Router with PPPoe settings using software from Router Manufacture. During the installation process a Timeout error was experienced, unable to connect to WAN. Used Internet Explorer to communicate directly with Router using IP address. Changed settings to use PPPoe settings given by ISP. Router was not able to communicate with Internet. Repeated steps 1-4 again with no success. Reset Router and DSL modem. Repeated steps 1-4 again still no success. Tried connecting Laptop-1 directly to DSL to gain access to internet to research problem. No Network connection with DSL could be established…connection would be established for a second and then be lost and didn’t appear long enough to actually connect to DSL. Replugged LAN back into Router and connection was regained with laptop-1. Replugged Laptop-1 directly into DSL and again unable to establish network connection. Uninstalled network card and all of its drivers on Laptop-1. Reinstalled network card and drivers and tried connecting directly to DSL. Still unable to make network connection. Plugged DSL into Laptop-3 and Internet connection was established. Being Laptop-3 does not have a CD-Rom, Laptop-2 was tried to connect to the router. With Laptop-2 steps 1-7 ended up being repeated without success. Tried plugging Laptop-2 directly into DSL and again no network connection could be established. Using Laptop-3 with a direct connection to DSL downloaded latest Router FW. Installed router FW using Laptop-1. Tired the installation process again without success. Being desperate reinstalled OS on Laptop-1 still not success. Tried using “ipconfig” with router to see what was going on without success. With laptop-1 connected to DSL went through the “ipconfig /…” inputs to see if anything made a difference. Being the network card was not able to make a connection this provide very little information “media disconnected”. So now I have a router and two laptops which are unable to connect to the internet and sure could use some advice/help.

  Read the article

• .dll Solidworks Add-in not registering in COM

  - by Abhijit

  I am trying to register this .dll in COM as an Add-in to Solid Works software. The dll is building without any error or warnings.But the Add-in is not appearing in the Windows "Registry Editor" as should be the case.Kindly suggest me a solution. Thanks in advance. Below is my code:- using System; using System.Collections; using System.Reflection; using System.Collections.Generic; using System.Linq; using System.Text; using SolidWorks.Interop.sldworks; using SolidWorks.Interop.swcommands; using SolidWorks.Interop.swconst; using SolidWorks.Interop.swpublished; using SolidWorksTools; using SolidWorksTools.File; using System.Runtime.InteropServices; using System.Diagnostics; namespace SWADDIN_Test { [ComVisible(true)] [Guid("C380F7A6-771A-41EE-807A-1689C8E97720")] [InterfaceType(ComInterfaceType.InterfaceIsIDispatch)] interface ISWIntegration { void DoSWIntegration(); }//end of interface Dummy ISWIntegration [Guid("5EE80911-9567-4734-8E55-C347EA4635B5")] [ClassInterface(ClassInterfaceType.None)] [ProgId("SWADDIN_Test.SWIntegration")] [ComVisible(true)] public class SWIntegration : ISwAddin,ISWIntegration { public SldWorks mSWApplication; private int mSWCookie; public SWIntegration() { mSWApplication = null; mSWCookie = 0; }//end of parameterless constructor public void DoSWIntegration() { }//end of dummy method DoSWIntegration public bool ConnectToSW(object ThisSW, int Cookie) { mSWApplication = (SldWorks)ThisSW; mSWCookie = Cookie; // Set-up add-in call back info bool result = mSWApplication.SetAddinCallbackInfo(0, this, Cookie); this.UISetup(); return true; }//end of method ConnectToSW() public bool DisconnectFromSW() { return UITeardown(); }//end of method DisconnectFromSW() public void UISetup() { }//end of method UISetup() public bool UITeardown() { return true; }//end of method UITeardown() [ComRegisterFunction()]//Attribute private static void ComRegister(Type t) { string keyPath = String.Format(@"SOFTWARE\SolidWorks\AddIns{0:b}", t.GUID); using (Microsoft.Win32.RegistryKey rk = Microsoft.Win32.Registry.LocalMachine.CreateSubKey(keyPath)) { rk.SetValue(null, 1);// Load at startup rk.SetValue("Title", "Abhijit_SwAddin"); // Title rk.SetValue("Description", "All your pixels now belong to us"); // Description }//end of using statement }//end of method ComRegister() [ComUnregisterFunction()]//Attribute private static void ComUnregister(Type t) { string keyPath = String.Format(@"SOFTWARE\SolidWorks\AddIns{0:b}", t.GUID); Microsoft.Win32.Registry.LocalMachine.DeleteSubKeyTree(keyPath); }//end of method ComUnregister() }//end of class SWIntegration }//end of namespace SWADDIN_Test

  Read the article

• VMWare tools not installing with an error

  - by JDS

  VMWare tools not installing on Ubuntu 12.04. I'm using Chef to manage the installation, but the Apt commands fail if run manually. I'm using the VMWare tool Debian repo. Example: $ cat /etc/apt/sources.list.d/vmware-tools-source.list deb http://packages.vmware.com/tools/esx/5.0u2/ubuntu precise main When trying to install, most packages seem to go ok, but one, "vmware-tools-foundation", does not. Example: $ apt-get -q -y install vmware-tools-esx-nox=8.6.10-1.precise Reading package lists... Building dependency tree... Reading state information... You might want to run 'apt-get -f install' to correct these: The following packages have unmet dependencies: vmware-tools-esx-kmods-3.2.0-23-generic : Depends: vmware-tools-foundation (>= 8.6.10) but it is not going to be installed vmware-tools-esx-nox : Depends: ...snip list of deps... E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution). $ apt-get -f install Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following extra packages will be installed: vmware-tools-foundation The following NEW packages will be installed: vmware-tools-foundation 0 upgraded, 1 newly installed, 0 to remove and 118 not upgraded. 7 not fully installed or removed. Need to get 0 B/5,886 B of archives. After this operation, 86.0 kB of additional disk space will be used. Do you want to continue [Y/n]? y (Reading database ... 103499 files and directories currently installed.) Unpacking vmware-tools-foundation (from .../vmware-tools-foundation_8.6.10-1.precise_all.deb) ... VMware Tools cannot install because it appears that another installation of VMware Tools is already present. Please remove the previous installation and then attempt to install this copy of VMware Tools again. dpkg: error processing /var/cache/apt/archives/vmware-tools-foundation_8.6.10-1.precise_all.deb (--unpack): subprocess new pre-installation script returned error exit status 1 Errors were encountered while processing: /var/cache/apt/archives/vmware-tools-foundation_8.6.10-1.precise_all.deb E: Sub-process /usr/bin/dpkg returned an error code (1) The key seems to be this error: "VMware Tools cannot install because it appears that another installation of VMware Tools is already present. Please remove the previous installation and then attempt to install this copy of VMware Tools again." However, I've tryed removing and purging and can't seem to "trick" VMWare tools into thinking the packages are gone. Apt thinks they are gone. Is there some service/file/cache/lock left that VMWare tools sees that makes it think that VMWare tools are still installed? I've googled and googled but there is no answer to this question with my particular circumstances on the interwebs. VMWare's documentation of this error is minimal.

  Read the article

• Starting/Stopping Custom PHP Chat Server Linux Service (CentOS)

  - by chad

  I have been trying all night to get this service working properly. I created this script from a template and am very new to bash coding. I wrote a fully functioning chat server in php which runs endlessly, but now want to make it a dedicated service. I want to do this so that it starts on server boot and boots back up if possible when there are any down-times with the server. The issue is that I need this thing to run in a detached screen so that I can monitor packet data or send server commands via SSH when need-be. The main problem that i'm having is that it needs to have its own PID when it starts so that I can stop/restart it when needed. I am the type who grinds on coding until I figure it out, but this is so new to me that it seems the learning curve here is very steep and frustrating. Below is my code if anybody can please help me with this one, i've gotten so tired I can't even concentrate any more :( #!/bin/sh # # chatserver # # chkconfig: 345 20 90 # description: chatServer Linux Service Daemon \ # for general server handling ### BEGIN INIT INFO # Provides: chatserver # Required-Start: $local_fs $network $named $syslog # Required-Stop: $local_fs $syslog # Default-Start: 3 4 5 # Default-Stop: 0 1 2 6 # Short-Description: This service maintains the chatServer # Description: chatServer Linux Service Daemon # for general server handling ### END INIT INFO # Source function library. . /etc/rc.d/init.d/functions exec="screen php -q /var/www/html/chatServer.php" prog="chatserver" config="/etc/sysconfig/$prog" pidfile="/var/run/chatserver.pid" [ -e /etc/sysconfig/$prog ] && . /etc/sysconfig/$prog lockfile=/var/lock/subsys/$prog start() { #$exec || exit 5 echo -n $"Starting $prog: " daemon $exec --name=$exec --pidfile=$pidfile retval=$? echo [ $retval -eq 0 ] && touch $lockfile return $retval } stop() { echo -n $"Stopping $prog: " killproc -p $pidfile rm -f $pidfile retval=$? echo [ $retval -eq 0 ] && rm -f $lockfile return $retval } restart() { stop start } reload() { restart } force_reload() { restart } rh_status() { # run checks to determine if the service is running or use generic status status $prog } rh_status_q() { rh_status >/dev/null 2>&1 } case "$1" in start) rh_status_q && exit 0 $1 ;; stop) rh_status_q || exit 0 $1 ;; restart) $1 ;; reload) rh_status_q || exit 7 $1 ;; force-reload) force_reload ;; status) rh_status ;; condrestart|try-restart) rh_status_q || exit 0 restart ;; *) echo $"Usage: $0 {start|stop|status|restart|condrestart|try-restart|reload|force-reload}" exit 2 esac exit $?

  Read the article

• Tracking down rogue disk usage

  - by Amadan

  I found several other questions regarding the theory behind my problem (e.g. this, this), but I don't know how to apply the answers to my machine. # du -hsx / 11000283 / # df -kT / Filesystem Type 1K-blocks Used Available Use% Mounted on /dev/mapper/csisv13-root ext4 516032952 361387456 128432532 74% / There is a big difference between 11G (du) and 345G (df). Where are the remaining 334G? It's not in deleted files. There was only one, it was short, and I truncated it just in case. This is what remains: # lsof -a +L1 / COMMAND PID USER FD TYPE DEVICE SIZE/OFF NLINK NODE NAME zabbix_ag 4902 zabbix 1w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4902 zabbix 2w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4906 zabbix 1w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4906 zabbix 2w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4907 zabbix 1w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4907 zabbix 2w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4908 zabbix 1w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4908 zabbix 2w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4909 zabbix 1w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4909 zabbix 2w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4910 zabbix 1w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4910 zabbix 2w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) I rebooted to see if fsck does anything. But, from /var/log/boot.log, it seems there are no issues: /dev/mapper/server-root: clean, 3936097/32768000 files, 125368568/131064832 blocks Thinking maybe someone overzealously reserved root space, I checked the master record: # tune2fs -l /dev/mapper/server-root tune2fs 1.42 (29-Nov-2011) Filesystem volume name: <none> Last mounted on: / Filesystem UUID: 86430ade-cea7-46ce-979c-41769a41ecbe Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Filesystem features: has_journal ext_attr resize_inode dir_index filetype needs_recovery extent flex_bg sparse_super large_file huge_file uninit_bg dir_nlink extra_isize Filesystem flags: signed_directory_hash Default mount options: user_xattr acl Filesystem state: clean Errors behavior: Continue Filesystem OS type: Linux Inode count: 32768000 Block count: 131064832 Reserved block count: 6553241 Free blocks: 5696264 Free inodes: 28831903 First block: 0 Block size: 4096 Fragment size: 4096 Reserved GDT blocks: 992 Blocks per group: 32768 Fragments per group: 32768 Inodes per group: 8192 Inode blocks per group: 512 Flex block group size: 16 Filesystem created: Fri Feb 1 13:44:04 2013 Last mount time: Tue Aug 19 16:56:13 2014 Last write time: Fri Feb 1 13:51:28 2013 Mount count: 9 Maximum mount count: -1 Last checked: Fri Feb 1 13:44:04 2013 Check interval: 0 (<none>) Lifetime writes: 1215 GB Reserved blocks uid: 0 (user root) Reserved blocks gid: 0 (group root) First inode: 11 Inode size: 256 Required extra isize: 28 Desired extra isize: 28 Journal inode: 8 First orphan inode: 28836028 Default directory hash: half_md4 Directory Hash Seed: bca55ff5-f530-48d1-8347-25c004f66d43 Journal backup: inode blocks The system is: # uname -a Linux server 3.2.0-67-generic #101-Ubuntu SMP Tue Jul 15 17:46:11 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux # cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.2 LTS" Does anyone have any tips on what exactly to do to find and hopefully reclaim the missing space?

  Read the article

• Fedora 13 post security update boot problem

  - by Alex

  Hello. About a month ago I installed a security update that had new Kernek 2.6.34.x from 2.6.33.x), this is when the problem occurred for the first time. After the install my computer would not boot at all, black screen without any visible hard drive activity (I gave it good 30 minutes on black screen, before took actions)... I poped in installation DVD and went in rescue mode to change back the boot option to old kernel (was just a guess where the problem was). After restart computer loaded just file, took a long time for it to start because of SELinux targeted policy relabel is required. Relabeling could take very long time depending on file size. I assumed that the update got messed up somehow and continued working with modified boot option. Couple of days ago, there was another kernel update. I installed it and same problem as before. This rules out corrupted update theory... Black screen right after 'BIOS' screen before OS gets loaded. I had to rescue system again... Below is copy of my grub.conf file. I am fairly new to LINUX (couple of years of experience), mostly development and basic config... nothing crazy. # grub.conf generated by anaconda # # Note that you do not have to rerun grub after making changes to this file # NOTICE: You have a /boot partition. This means that # all kernel and initrd paths are relative to /boot/, eg. # root (hd0,0) # kernel /vmlinuz-version ro root=/dev/mapper/vg_obalyuk-lv_root # initrd /initrd-[generic-]version.img #boot=/dev/sda default=2 timeout=0 splashimage=(hd0,0)/grub/splash.xpm.gz hiddenmenu title Fedora (2.6.34.6-54.fc13.i686.PAE) root (hd0,0) kernel /vmlinuz-2.6.34.6-54.fc13.i686.PAE ro root=/dev/mapper/vg_obalyuk-lv_root rd_LVM_LV=vg_obalyuk/lv_root rd_LVM_LV=vg_obalyuk/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us rhgb quiet initrd /initramfs-2.6.34.6-54.fc13.i686.PAE.img title Fedora (2.6.34.6-47.fc13.i686.PAE) root (hd0,0) kernel /vmlinuz-2.6.34.6-47.fc13.i686.PAE ro root=/dev/mapper/vg_obalyuk-lv_root rd_LVM_LV=vg_obalyuk/lv_root rd_LVM_LV=vg_obalyuk/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us rhgb quiet initrd /initramfs-2.6.34.6-47.fc13.i686.PAE.img title Fedora (2.6.33.8-149.fc13.i686.PAE) root (hd0,0) kernel /vmlinuz-2.6.33.8-149.fc13.i686.PAE ro root=/dev/mapper/vg_obalyuk-lv_root rd_LVM_LV=vg_obalyuk/lv_root rd_LVM_LV=vg_obalyuk/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us rhgb quiet initrd /initramfs-2.6.33.8-149.fc13.i686.PAE.img I like my system to be up to date... Let me know if I can post any other files that can be of help. Has anyone else had this problem? Does anyone has any ideas how to fix this problem? p.s. Anything helps, you ppl are great! thx for ur time.

  Read the article

• Convert mkv/h264 video so it can be played on a "mid-range" Sony Ericsson phone. (using Ubuntu).

  - by Johan

  Hi As a little experiment I thinking of converting some video/movies/tv-series into a format that could be playable on my K850, but to be a little bit more generic in this question let's say "mid range Sony Ericsson" phone since they all more or less behave the same and has the same screen resolution (240 x 320). I am looking for command line based tools (for Ubuntu), since I am thinking about writing a "convert and move" script later if it is successful. A lot of the video I have is encoded in mkv/h264, but since that is not supported by the phone I guess that I need to convert it into some mp4/mpeg4 low quality video. After some googling it seems like a good candidate for the job is ffmpeg, but that seems to be a very versatile tool with a lot of magic tricks. Am I on the right track? And if so how do I use ffmpeg to do this? Thanks Johan Update: After plating a little bit with ffmeg I noticed that it only uses 1 of my 4 cores, so the transcoding takes forever. I found a arg called -threads but that did not change much, maybe I got it wrong. I also found that something like this plays in the phone. ffmpeg -i Mythbusters\ S1D1_1.mkv -threads 4 -t 180 -vcodec mpeg4 -r 15 -s 320x240 Mythbusters\ S1D1_1_mini.mp4 It was possible to use 3gp/h263, but the quality was really useless. ffmpeg -i Mythbusters\ S1D1_1.mkv -t 180 -vcodec h263 -acodec libfaac -s cif Mythbusters\ S1D1_1_cif.3gp And it seems like mp4/h264 is also possible and the result is ok, thanks to this question, this one seem to use more than one core as well so it was a little bit faster for me. ffmpeg -i Mythbusters_S1D1_1.mkv -t 180 -acodec libfaac -ab 60k -s 320x240 -vcodec libx264 -b 500k -flags +loop -cmp +chroma -partitions +parti4x4+partp8x8+partb8x8 -flags2 +mixed_refs -me_method umh -subq 6 -trellis 1 -refs 5 -coder 0 -me_range 16 -g 250 -keyint_min 25 -sc_threshold 40 -i_qfactor 0.71 -bt 500k -maxrate 768k -bufsize 2M -qcomp 0.6 -qmin 10 -qmax 51 -qdiff 4 -level 13 -threads 0 -f mp4 Mythbusters_S1D1_1_qvga.mp4 Update: I have tried to use HandBrakeCLI and it is no problem creating a new file that seem to be the same as the one created with ffmpeg with something like this. HandBrakeCLI -i Mythbusters_S1D1_1.mkv --size 100 -E faac -B 60 --maxHeight 240 -r 15 -e x264 -o Mythbusters_S1D1_1_hand.mp4 But that one did not play in the phone... I found this in the official manual: If you transfer video clips using another program than Media Go™, we recommend that you select H.264 Baseline profile video, up to QVGA at 30 fps, VBR 384 kbps (max 768 kps) with AAC+ audio at 128 kbps (max 255 kbps), 48 kHz and stereo audio in mp4 file format. So the idea to use H264 seems to be correct.

  Read the article

• Windows XP machine not seeing external FAT32 partitions correctly

  - by Rob_before_edits

  About 8 months ago my Windows XP machine stopped being able to see FAT32 external drives when I plug them in... mostly. I will explain... It happens with all my FAT32 drives, whether they be unpowered external hard drives, powered external hard drives, SDHC cards plugged directly into the machine's card reader, or SDHC cards plugged in via a separate USB card reader. All of these drives/cards used to work fine on this machine. They all stopped working at about the same time. NTFS volumes are not affected. If I plug in NTFS external drives they are recognized right away. I even have one external drive with two partitions on it, one is NTFS which is recognized, the other is FAT32, which is not recognized. If I attach a FAT32 drive, then reboot, then the drive almost always becomes visible to the machine after the reboot. Sometimes I can plug in a FAT32 drive and it works right away. Not often though. I'd say I get lucky more often with SDHC cards than hard drives. I'm developing a theory that I only get lucky with hard drives if I'm running Acronis Disk Director when I plug them in, though that usually doesn't work either - I need more data here, this may be a red herring. Getting lucky with a hard drive is really rare, usually I have to reboot. When a FAT32 is recognized, either because I got lucky or because I rebooted, I can almost never safely disconnect it. It tells me "The device 'Generic volume' cannot be stopped right now. Try stopping the device again later". I can't seem to get around this. IIRC, I've tried closing every open window, and still no luck. Since I care about my data usually the only way to disconnect a FAT32 drive is to shut down the machine. As you can imagine, two reboots just to read a drive is getting pretty old... When the machine fails to see a FAT32 drive it usually comes up with the appropriate drive letter and the words "Local Disk" in Windows Explorer instead of the correct partition name. If I click on it I get "J:\ is not accessible. The parameter is incorrect." Before this problem arose I always clicked the "safely remove" button for everything, including SDHC cards where I think it's not necessary. I've known for a long time that this is the correct procedure for hard drives, so I don't think failing to do this was the cause of this problem (before someone asks :) Any answers or suggestions most welcome.

  Read the article

• GeForce 8800GT not even giving basic output

  - by Sam

  My Dad bought a GeForce 8800GT graphics card quite a long time ago now. It has never worked in his PC. Print out from a dxdiag: System Information Time of this report: 4/13/2010, 19:52:40 Machine name: USER-PC Operating System: Windows Vista™ Home Premium (6.0, Build 6001) Service Pack 1 (6001.vistasp1_gdr.091208-0542) Language: English (Regional Setting: English) System Manufacturer: To Be Filled By O.E.M. System Model: To Be Filled By O.E.M. BIOS: Default System BIOS Processor: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz (4 CPUs), ~2.3GHz Memory: 2046MB RAM Page File: 1045MB used, 3296MB available Windows Dir: C:\Windows DirectX Version: DirectX 10 DX Setup Parameters: Not found DxDiag Version: 6.00.6001.18000 32bit Unicode DxDiag Notes Display Tab 1: No problems found. Sound Tab 1: No problems found. Sound Tab 2: No problems found. Sound Tab 3: No problems found. Input Tab: No problems found. DirectX Debug Levels Direct3D: 0/4 (retail) DirectDraw: 0/4 (retail) DirectInput: 0/5 (retail) DirectMusic: 0/5 (retail) DirectPlay: 0/9 (retail) DirectSound: 0/5 (retail) DirectShow: 0/6 (retail) Display Devices Card name: ATI Radeon HD 2400 PRO Manufacturer: ATI Technologies Inc. Chip type: ATI Radeon Graphics Processor (0x94C3) DAC type: Internal DAC(400MHz) Device Key: Enum\PCI\VEN_1002&DEV_94C3&SUBSYS_00000000&REV_00 Display Memory: 1012 MB Dedicated Memory: 245 MB Shared Memory: 767 MB Current Mode: 1280 x 960 (32 bit) (75Hz) Monitor: Generic PnP Monitor Driver Name: atiumdag.dll,atiumdva.dat,atitmmxx.dll Driver Version: 7.14.0010.0523 (English) DDI Version: 10 Driver Attributes: Final Retail Driver Date/Size: 8/22/2007 02:43:14, 3021312 bytes That info is from the current card that is installed in it and has been installed since its purchase roughly 3-4 years ago. When I physically install the card I put it into a purple slot on the motherboard that the old card was in (if I go into the device manager and select properties on the current card it confirms that the slot is a "PCI Slot 16 (PCI bus 2, device 0, function 0)") and boot up the computer but get absolutely no output. The screen that we have registers that it is connected to something (by not displaying the screen it does when the cable is unplugged) but just remains blank, no output at all. I recently took the card to my University and one of my friends who is better with hardware issues than I am tried it in his system and it worked perfectly. No issues whatsoever. I do not have a spec list for his system but I could get one if you need it. If you need any more information on this issue I will be happy to supply you with it as I am starting to get very annoyed with this problem ^_^

  Read the article

• Can't set up printing from Mac OS X (10.5.7) to an HP PSC 2410 shared from PC running Ubuntu 9.10

  - by Weston C

  I've got an HP PSC 2410 printer shared from a fresh Ubuntu 9.10 installation. I'm able to send documents to this printer over the network from another Ubuntu machine. But so far, I haven't been able to find a setup where I can send documents to that printer from a MacBook running 10.5.7. On the Mac side, when setting things up, I go into System Prefs Print & Fax, click on the "+" mark, select "IP", pick "IPP", enter the IP address of the Ubuntu box, leave the queue blank, enter the Name and location, and I think it's when I get to the "Print Using" (driver selection) part that I'm running into issues. If I use "Auto Select", it defaults to "Generic PostScript Printer", which I doubt the PSC 2410 is (and sure enough, if I print, the jobs don't go through). If I try "Select a driver to use...", there's not an option for an HP PSC 2400. This seems a little odd: I can plug the printer directly into one of our Macs and it immediately figures out the driver and I can print no problem, but that's apparently the way things work. So, that leaves one option: "Other", which, when selected, brings up a dialog apparently for the purpose of manually locating a driver. I've tried visiting HP's web site. They have drivers for earlier versions of Mac OS X, but state that after 10.4, Mac OS X should just come with the relevant drivers. I've also tried setting things up by interacting with the CUPS server on the Mac through a browser: I go to http://localhost:631/, select "Add New Printer", pick "Internet Printing Protocol (http)" for the Device selection, enter "http://ubuntu.machine.ip.address:631/printers/hp-psc-2400-series" for the Device URI, select "HP" for Make, and then on the next screen, we're back to the problem where the PSC 2400 just doesn't show up. There's an option to "provide a PPD file", which I assume would be the printer driver I can't find. A Google search for "HP PSC 2410 ppd Leopard" doesn't seem to yield much other than a reminder that the printer is supposed to just work out of the box on Leopard. A local search for ".ppd" or "2410" on either Mac also doesn't yield anything that looks like a relevant print driver. I'm totally stuck at this point. Any advice?

  Read the article

• Unable to use TweetDeck on Windows due to "Ooops, TweetDeck can't find your data" and "Sorry, Adobe

  - by Matt

  I'm running Adobe AIR 1.5.2 (latest) on Windows 7 (64-bit RTM) and downloaded TweetDeck 0.31.1 (latest). When I run TweetDeck I get the following errors: Ooops, TweetDeck can't find your data and Sorry, Adobe AIR has a problem running on this computer Other AIR applications install and run fine. I've uninstalled both TweetDeck and AIR and reinstalled. Following the uninstalls I've also removed all on-disk references to both TweetDeck and AIR, but no luck. UPDATE: Using Process Monitor I did a trace of Tweetdeck from the moment it launched until the first error occurred. I saw the following information in the output of the trace: 1 5:22:18.6522338 PM TweetDeck.exe 5580 CreateFile D:\ProgramData\Microsoft\Windows\Start Menu\Programs\rs\??\d:\Use\myusername\AppData\Roaming\Adobe\AIR\ELS\TweetDeckFast.F9107117265DB7542C1A806C8DB837742CE14C21.1\PrivateEncryptedDatak NAME INVALID Desired Access: Generic Write, Read Attributes, Disposition: OverwriteIf, Options: Synchronous IO Non-Alert, Non-Directory File, Attributes: N, ShareMode: Read, Write, AllocationSize: 0 In this trace output, Tweetdeck.exe is trying to create the file D:\ProgramData\Microsoft\Windows\Start Menu\Programs\rs\??\d:\Use\myusername\AppData\Roaming\Adobe\AIR\ELS\TweetDeckFast.F9107117265DB7542C1A806C8DB837742CE14C21.1\PrivateEncryptedDatak but the path specified is invalid. When looking at the path you can see that it is indeed an invalid path. First, there’s the “??” portion which doesn’t exist in the file system since the “?” is an invalid character in Windows/NTFS file systems. Additionally, looking at this path, it actually seems to be composed of two parts (is the "??" a delimiter?): Part 1: D:\ProgramData\Microsoft\Windows\Start Menu\Programs\rs\?? Part 2: d:\Use\myusername\AppData\Roaming\Adobe\AIR\ELS \TweetDeckFast.F9107117265DB7542C1A806C8DB837742CE14C21.1\PrivateEncryptedDatak (the problem here is that d:\Use... doesn’t even exist. What seems to be happening here is that Tweetdeck is looking for the user credentials (the “PrivateEncryptedDatak” file) but it’s looking in the wrong place, can’t find the file, and hence the error that Tweetdeck is giving (shown in the screenshot). I'm trying to determine how TweetDeck is getting this path. I searched the contents of all files on my hard disk hoping to find some TweetDeck or Adobe AIR configuration file containing this incorrect path, but I was unable to find anything. UPDATE: See Carl's comment regarding directory junctions and symbolic links under my accepted answer. This ended up being the problem. Edit by Gnoupi: People, the answer section is there to provide an actual ANSWER, not to say you have the same issue. It doesn't help anyone that you have the same problem. Eventually, if you think this is really worth mentioning, put it as a comment under the question. But simply, if what you want to add is not an answer to the question, then don't post it as an answer. This is not a forum, I recommend new users to read the FAQ: http://superuser.com/faq

  Read the article

• Why does Ubuntu 9.10 hang during boot at "Booting processor 1 APIC 0x1 ip 0x6000"?

  - by BraeburnDev

  I recently installed a new copy of Ubuntu 9.10 (Kernel 2.6.31-14) on to my Hp Pavilion dv6t, so I can setup a Linux development environment. The install went flawlessly and I proceeded with Ubuntu's udate manager's long list of updates (292 in all). I also setup a swap file and activated a Nvidia 185 driver for the Nvidia 260m GPU on the machine. After all this was done I restarted the computer and booted into Ubuntu this time with a newer 2.6.31-19 Kernel which was installed from the update manager. During booth the computer hung at this point: Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013136] Performance Counters: Nehalem/Corei7 events, Intel PMU driver. Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013141] ... version: 3 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013142] ... bit width: 48 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013144] ... generic counters: 4 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013146] ... value mask: 0000ffffffffffff Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013147] ... max period: 000000007fffffff Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013149] ... fixed-purpose counters: 3 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013151] ... counter mask: 000000070000000f Feb 24 14:23:12 braeburn-laptop kernel: [ 0.015539] ACPI: Core revision 20090521 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.052264] Setting APIC routing to flat Feb 24 14:23:12 braeburn-laptop kernel: [ 0.052639] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.152580] CPU0: Intel(R) Core(TM) i7 CPU Q 720 @ 1.60GHz stepping 05 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.270845] Booting processor 1 APIC 0x1 ip 0x6000 I can post a full kern.log of this boot process if requested. Hopefully this is enough information to go on. I should add that I'm still new to configuring and running a Linux OS although I know enough basic command line usage to do software development. This is my attempt to become more familiar with Linux and manage my own system. I'd like to get some insight on the nature of this system hang, what the problem is and how to resolve it. At this point I can scrap the install if I broke something, but my intuition says this is an issue with the kernel recognizing the correct hardware configuration for my system, or perhaps this is an issue with the APIC drivers managing Nehalem's new power management capabilities? Thanks for looking at this issue and providing feed back.

  Read the article

• 64-bit linux kernel only seeing 3 of 4GB after upgrade...

  - by Blaine

  Hey everyone. I am running Ubuntu 9.04 64-bit on my macbook. I had 2GB of ram before, and everything ran great. I just upgraded to 2x2GB (4GB), but my system only sees 3GB of it. OS X, which I am dual booting, sees all 4GB. Also, my video performance is incredibly lacking. Before the upgrade my compiz benchmark was full at 80fps, and now it is at 22fps with very choppy window dragging. Has anyone ever heard of this on a 64-bit kernel? I just don't quite understand what could be the issue. 10$ uname -a Linux macbook 2.6.28-15-generic #49-Ubuntu SMP Tue Aug 18 19:25:34 UTC 2009 x86_64 GNU/Linux $ free -m total used free shared buffers cached Mem: 2953 1031 1921 0 114 427 -/+ buffers/cache: 489 2463 Swap: 7812 0 7812 9$ lsmod Module Size Used by i915 77960 2 drm 123232 3 i915 binfmt_misc 18572 1 ppdev 16904 0 btusb 21784 2 bridge 63776 0 stp 11140 1 bridge bnep 22912 2 vboxnetadp 109356 0 vboxnetflt 116972 0 vboxdrv 1721612 1 vboxnetflt uvcvideo 69640 0 compat_ioctl32 18304 1 uvcvideo videodev 45184 2 uvcvideo,compat_ioctl32 v4l1_compat 23940 2 uvcvideo,videodev lp 19588 0 parport 49584 2 ppdev,lp snd_hda_intel 557492 3 snd_pcm_oss 52352 0 snd_mixer_oss 24960 1 snd_pcm_oss snd_pcm 99464 2 snd_hda_intel,snd_pcm_oss arc4 10240 2 snd_seq_dummy 11524 0 ecb 11392 2 snd_seq_oss 41984 0 snd_seq_midi 15744 0 snd_rawmidi 33920 1 snd_seq_midi snd_seq_midi_event 16512 2 snd_seq_oss,snd_seq_midi snd_seq 66272 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event ath9k 310584 0 snd_timer 34064 2 snd_pcm,snd_seq snd_seq_device 16276 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq mac80211 251528 1 ath9k iTCO_wdt 21712 0 iTCO_vendor_support 12420 1 iTCO_wdt joydev 20992 0 video 29204 0 snd 78920 15 snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device applesmc 37700 0 output 11648 1 video soundcore 16800 1 snd pcspkr 11136 0 cfg80211 43680 1 mac80211 appletouch 19972 0 isight_firmware 11520 0 input_polldev 12688 1 applesmc intel_agp 39408 1 snd_page_alloc 18704 2 snd_hda_intel,snd_pcm led_class 13064 2 ath9k,applesmc hid_apple 15872 0 usbhid 47040 0 ohci1394 42164 0 ieee1394 108288 1 ohci1394 sky2 63364 0 fbcon 49792 0 tileblit 11264 1 fbcon font 17024 1 fbcon bitblit 14464 1 fbcon softcursor 10368 1 bitblit Some information from dmesg: [ 795.820163] ACPI: EC: GPE storm detected, transactions will use polling mode [ 1762.709516] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 1763.078130] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 2362.760889] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 2416.352084] ACPI: EC: missing confirmations, switch off interrupt mode. [ 3718.721095] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 3719.108914] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 4318.773266] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 9513.813066] CE: hpet increasing min_delta_ns to 15000 nsec [ 9693.815684] npviewer.bin[6736]

  Read the article

• USB Flash not recognised by Windows and BIOS, but works fine in Linux

  - by bbalegere

  I have a Transcend JetFLash 2GB USB Drive.It was working fine and I had been using it occasionally. All of sudden it stopped working in all versions of Windows . The USB Drive is also not recognised by the BIOS.It does not show in the list of bootable devices.(It used show up in the list earlier) However the USB Drive works fine in my Linux Mint 11 OS. Running dmesg gives this [ 941.812192] usb 1-2: new high speed USB device using ehci_hcd and address 4 [ 941.936178] usb 1-2: device descriptor read/64, error -71 [ 942.164188] usb 1-2: device descriptor read/64, error -71 [ 942.380189] usb 1-2: new high speed USB device using ehci_hcd and address 5 [ 942.504138] usb 1-2: device descriptor read/64, error -71 [ 942.732179] usb 1-2: device descriptor read/64, error -71 [ 942.948154] usb 1-2: new high speed USB device using ehci_hcd and address 6 [ 943.364134] usb 1-2: device not accepting address 6, error -71 [ 943.476172] usb 1-2: new high speed USB device using ehci_hcd and address 7 [ 943.892140] usb 1-2: device not accepting address 7, error -71 [ 943.892191] hub 1-0:1.0: unable to enumerate USB device on port 2 [ 944.296190] usb 2-2: new full speed USB device using uhci_hcd and address 3 [ 944.438251] usb 2-2: not running at top speed; connect to a high speed hub [ 944.709928] usbcore: registered new interface driver uas [ 944.729999] Initializing USB Mass Storage driver... [ 944.730509] scsi6 : usb-storage 2-2:1.0 [ 944.730908] usbcore: registered new interface driver usb-storage [ 944.730917] USB Mass Storage support registered. [ 945.736320] scsi 6:0:0:0: Direct-Access JetFlash Transcend 2GB 8.07 PQ: 0 ANSI: 2 [ 945.744547] sd 6:0:0:0: Attached scsi generic sg1 type 0 [ 945.753316] sd 6:0:0:0: [sdb] 3944448 512-byte logical blocks: (2.01 GB/1.88 GiB) [ 945.758274] sd 6:0:0:0: [sdb] Write Protect is off [ 945.758288] sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00 [ 945.765167] sd 6:0:0:0: [sdb] No Caching mode page present [ 945.765181] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 945.784309] sd 6:0:0:0: [sdb] No Caching mode page present [ 945.784323] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 946.239512] sdb: sdb1 [ 946.257279] sd 6:0:0:0: [sdb] No Caching mode page present [ 946.257292] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 946.257302] sd 6:0:0:0: [sdb] Attached SCSI removable disk Looks like there is something wrong the USB Drive.It is not recognised in any computer running Windows. Is there any way to fix this? Any idea why this problem occurred ?

  Read the article

• RSH between servers not working

  - by churnd

  I have two servers: one CentOS 5.8 & one Solaris 10. Both are joined to my workplace AD domain via PBIS-Open. A user will log into the linux server & run an application which issues commands over RSH to the solaris server. Some commands are also run on the linux server, so both are needed. Due to the application these servers are being used for (proprietary GE software), the software on the linux server needs to be able to issue rsh commands to the solaris server on behalf of the user (the user just runs a script & the rest is automatic). However, rsh is not working for the domain users. It does work for a local user, so I believe I have the necessary trust settings between the two servers correct. However, I can rlogin as a domain user from the linux server to the solaris server. SSH works too (how I wish I could use it). Some relevant info: via rlogin: [user@linux~]$ rlogin solaris connect to address 192.168.1.2 port 543: Connection refused Trying krb4 rlogin... connect to address 192.168.1.2 port 543: Connection refused trying normal rlogin (/usr/bin/rlogin) Sun Microsystems Inc. SunOS 5.10 Generic January 2005 solaris% via rsh: [user@linux ~]$ rsh solaris ls connect to address 192.168.1.2 port 544: Connection refused Trying krb4 rsh... connect to address 192.168.1.2 port 544: Connection refused trying normal rsh (/usr/bin/rsh) permission denied. [user@linux ~]$ relevant snippet from /etc/pam.conf on solaris: # # rlogin service (explicit because of pam_rhost_auth) # rlogin auth sufficient pam_rhosts_auth.so.1 rlogin auth requisite pam_lsass.so set_default_repository rlogin auth requisite pam_lsass.so smartcard_prompt try_first_pass rlogin auth requisite pam_authtok_get.so.1 try_first_pass rlogin auth sufficient pam_lsass.so try_first_pass rlogin auth required pam_dhkeys.so.1 rlogin auth required pam_unix_cred.so.1 rlogin auth required pam_unix_auth.so.1 # # Kerberized rlogin service # krlogin auth required pam_unix_cred.so.1 krlogin auth required pam_krb5.so.1 # # rsh service (explicit because of pam_rhost_auth, # and pam_unix_auth for meaningful pam_setcred) # rsh auth sufficient pam_rhosts_auth.so.1 rsh auth required pam_unix_cred.so.1 # # Kerberized rsh service # krsh auth required pam_unix_cred.so.1 krsh auth required pam_krb5.so.1 # I have not really seen anything useful in either system log that seem to be directly related to the failed login attempt. I've tail -f'd /var/adm/messages on solaris & /var/log/messages on linux during the failed attempts & nothing shows up. Maybe I need to be doing something else?

  Read the article

• grep simply fails when used on a few files

  - by Reid

  I've been trying for about the past 30 minutes to get this to work properly. grep is not exactly the most difficult thing to use, so I'm somewhat baffled as to why this won't work. The files I'm trying to use grep on are simple XHTML log files. Their names are in the format [email protected], though I don't think that should matter, and inside is simple XHTML. I copied one such log file to be testfile so you can see the output of some commands and why it's baffling to me: [~/.chatlogs_windows/dec] > whoami reid [~/.chatlogs_windows/dec] > type grep grep is /bin/grep [~/.chatlogs_windows/dec] > uname -a Linux reid-pc 2.6.35-22-generic #33-Ubuntu SMP Sun Sep 19 20:32:27 UTC 2010 x86_64 GNU/Linux [~/.chatlogs_windows/dec] > head -1 /etc/issue Linux Mint 10 Julia [~/.chatlogs_windows/dec] > ls -Alh | grep testfile -rw-r--r-- 1 reid reid 63K 2011-01-10 12:45 testfile [~/.chatlogs_windows/dec] > tail -3 testfile </body> </html> [~/.chatlogs_windows/dec] > file testfile testfile: XML document text [~/.chatlogs_windows/dec] > grep html testfile [~/.chatlogs_windows/dec] > grep body testfile [~/.chatlogs_windows/dec] > grep "</html>" testfile [~/.chatlogs_windows/dec] > grep "</body>" testfile [~/.chatlogs_windows/dec] > cat testfile | grep html [~/.chatlogs_windows/dec] > cat testfile | wc -l 231 [~/.chatlogs_windows/dec] > cat testfile | tail -3 </body> </html> [~/.chatlogs_windows/dec] > chmod a+rw testfile && ls -Alh | grep testfile -rw-rw-rw- 1 reid reid 63K 2011-01-10 12:45 testfile [~/.chatlogs_windows/dec] > grep html testfile That's what I'm attempting to do. I want to just use grep -ri query . in ~/.chatlogs_windows, which normally works perfectly for me... but for some reason, it completely fails at going through these files. If it matters, I copied these files off of my Windows 7 partition. But I chown'd them and gave myself all the appropriate permissions, and other programs (like cat) seem to read them just fine. I also copied testfile to testfile_unix and converted the line endings and tried that, but it didn't work either. I'm using zsh, but I tried it on bash and that failed too. Also, grep works normally: I tried it out on my documents folder and it worked flawlessly. If you need any more information, just let me know. I tried googling around, but I found no reason for grep to simply not work. Thanks in advance.

  Read the article

• configuring slime in emacs

  - by CodeKingPlusPlus

  I am in the process of configuring slime for emacs. So far I have read about basic functionality for common lisp such as C-c C-q which invokes the command slime-close-parens-at-point which places the proper number of parens where your mouse is. Another command that seemed cool was invoked by C-c C-c and it would pass the code you are editing in a buffer to the REPL, and "compile" it. Why won't these commands work for me? Anyway, I have downloaded slime via M-x list-packages and do not seem to have this functionality (C-h w and then any of these commands tells me that these commands do note exist). So, I saw a bunch of other slime extensions such as slime-repl', 'slime-fuzzy' and 'hippie-expand-slime'. So I again usedM-x list-packages` and downloaded them. Still I did not have these commands. Here is the content of my emacs file relevant to slime: ;;;Common Lisp and Slime (add-to-list 'load-path "/home/s2s2/.emacs.d/elpa/slime-20130626.1151") (add-to-list 'load-path "/home/s2s2/.emacs.d/elpa/slime-repl-201000404") (add-to-list 'load-path "/home/s2s2/.emacs.d/elpa/hippie-expand-slime-20130226.1656") (add-to-list 'load-path "/home/s2s2/.emacs.d/elpa/slime-fuzzy-20100404") (require 'slime) (setq slime-lisp-implementations `((sbcl ("/usr/bin/sbcl")) (ecl ("/usr/bin/ecl")) (clisp ("/usr/bin/clisp" "-q -I")))) (require 'slime-repl) (require 'slime-fuzzy) (require 'hippie-expand-slime) When I execute M-x slime I get the following message in the inferior-lisp buffer where I can execute common lisp code (however, shouldn't this be the slime-repl since I required it?): STYLE-WARNING: redefining EMACS-INSPECT (#<BUILT-IN-CLASS T>) in DEFMETHOD STYLE-WARNING: Implicitly creating new generic function STREAM-READ-CHAR-WILL-HANG-P. WARNING: These Swank interfaces are unimplemented: (DISASSEMBLE-FRAME SLDB-BREAK-AT-START SLDB-BREAK-ON-RETURN) ;; Swank started at port: 46533. Then a slime-error buffer is created with the contents: Invalid protocol message: Symbol "CREATE-REPL" not found in the SWANK package. Line: 1, Column: 28, File-Position: 28 Stream: #<SB-IMPL::STRING-INPUT-STREAM {10056B9C33}> (:emacs-rex (swank:create-repl nil) "COMMON-LISP-USER" t 5) How should I modify my emacs file to give me the functionality of those commands? In my emacs file am I not loading the necessary files? Do I need to install an additional package? If you need more information let me know! All help is much appreciated!

  Read the article

• CakePHP in a subdirectory using nginx (Rewrite rules?)

  - by lhnz

  I managed to get this to work a while back, but on returning to the cakephp project I had started it seems that whatever changes I've made to nginx recently (or perhaps a recent update) have broken my rewrite rules. Currently I have: worker_processes 1; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; sendfile on; keepalive_timeout 65; server { listen 80; server_name localhost; location / { root html; index index.php index.html index.htm; } location /basic_cake/ { index index.php; if (-f $request_filename) { break; } if (!-f $request_filename) { rewrite ^/basic_cake/(.+)$ /basic_cake/index.php?url=$1 last; break; } } location /cake_test/ { index index.php; if (-f $request_filename) { break; } if (!-f $request_filename) { rewrite ^/cake_test/(.+)$ /cake_test/index.php?url=$1 last; break; } } # redirect server error pages to the static page /50x.html # error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9000 # location ~ \.php$ { root html; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include fastcgi_params; } } server { listen 8081; server_name localhost; root /srv/http/html/xsp; location / { index index.html index.htm index.aspx default.aspx; } location ~ \.(aspx|asmx|ashx|asax|ascx|soap|rem|axd|cs|config|dll)$ { fastcgi_pass 127.0.0.1:9001; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include fastcgi_params; } } } The problem that I have is that the css and images will not load from the webroot. Instead if I visit http://localhost/basic_cake/css/cake.generic.css, I get a page which tells me: CakePHP: the rapid development php framework Missing Controller Error: CssController could not be found. Error: Create the class CssController below in file: app/controllers/css_controller.php var $name = 'Css'; } ? Notice: If you want to customize this error message, create app/views/errors/missing_controller.ctp CakePHP: the rapid development php framework Does anybody have any ideas on how to fix this?

  Read the article

• programatically check if a domain is availible?

  - by acidzombie24

  Using this solution http://serverfault.com/questions/98940/bot-check-if-a-domain-name-is-availible/98956#98956 I wrote a quick script (pasted below) in C# to check if the domain MIGHT be available. A LOT of results come up with taken domains. It looks like all 2 and 3 letter .com domains are taken and it looks like all 3 letter are taken (not including numbers which many are available). Is there a command or website to take my list of domains and check if they are registered or available? using System; using System.Collections.Generic; using System.Linq; using System.Text; using System.Text.RegularExpressions; using System.Diagnostics; using System.IO; namespace domainCheck { class Program { static void Main(string[] args) { var sw = (TextWriter)File.CreateText(@"c:\path\aviliableUrlsCA.txt"); int countIndex = 0; int letterAmount=3; char [] sz = new char[letterAmount]; for(int z=0; z<letterAmount; z++) { sz[z] = '0'; } //*/ List<string> urls = new List<string>(); //var sz = "df3".ToCharArray(); int i=0; while (i <letterAmount) { if (sz[i] == '9') sz[i] = 'a'; else if (sz[i] == 'z') { if (i != 0 && i != letterAmount - 1) sz[i] = '-'; else { sz[i] = 'a'; i++; continue; } } else if (sz[i] == '-') { sz[i] = 'a'; i++; continue; } else sz[i]++; string uu = new string(sz); string url = uu + ".ca"; Console.WriteLine(url); Process p = new Process(); p.StartInfo.UseShellExecute = false; p.StartInfo.RedirectStandardError = true; p.StartInfo.RedirectStandardOutput = true; p.StartInfo.FileName = "nslookup "; p.StartInfo.Arguments = url; p.Start(); var res = ((TextReader) new StreamReader( p.StandardError.BaseStream)).ReadToEnd(); if (res.IndexOf("Non-existent domain") != -1) { sw.WriteLine(uu); if (++countIndex >= 100) { sw.Flush(); countIndex = 0; } urls.Add(uu); Console.WriteLine("Found domain {0}", url); } i = 0; } Console.WriteLine("Writing out list of urls"); foreach (var u in urls) Console.WriteLine(u); sw.Close(); } } }

  Read the article

• Bypassing "Found New Hardware Wizard" / Setting Windows to Install Drivers Automatically

  - by Synetech inc.

  Hi, My motherboard finally died after the better part of a decade, so I bought a used system. I put my old hard-drive and sound-card in the new system, and connected my old keyboard and mouse (the rest of the components—CPU, RAM, mobo, video card—are from the new system). I knew beforehand that it would be a challenge to get Windows to boot and install drivers for the new hardware (particularly since the foundational components are new), but I am completely unable to even attempt to get through the work of installing drivers for things like the video card because the keyboard and mouse won't work (they do work, in the BIOS screen, in DOS mode, in Windows 7, in XP's boot menu, etc., just not in Windows XP itself). Whenever I try to boot XP (in normal or safe mode), I get a bunch of balloons popping up for all the new hardware detected, and a New Hardware Found Wizard for Processor (obviously it has to install drivers for the lowest-level components on up). Unfortunately I cannot click Next since the keyboard and mouse won't work yet because the motherboard drivers (for the PS/2 or USB ports) are not yet installed. I even tried a serial mouse, but to no avail—again, it does work in DOS, 7, etc., but not XP because it doesn't have the serial port driver installed. I tried mounting the SOFTWARE and SYSTEM hives under Windows 7 in order to manually set the "unsigned drivers warning" to ignore (using both of the driver-signing policy settings that I found references to). That didn't work; I still get the wizard. They are not even fancy, proprietary, third-party, or unsigned drivers. They are drivers that come with Windows—as the drivers for CPU, RAM, IDE controller, etc. tend to be. And the keyboard and mouse drivers are the generic ones at that (but like I said, those are irrelevant since the drivers for the ports that they are connected to are not yet installed). Obviously at some point in time over the past several years, a setting got changed to make Windows always prompt me when it detects new hardware. (It was also configured to show the Shutdown Event Tracker on abnormal shutdowns, so I had to turn that off so that I could even see the desktop.) Oh, and I tried deleting all of the PNF files so that they get regenerated, but that too did not help. Does anyone know how I can reset Windows to at least try to automatically install drivers for new hardware before prompting me if it fails? Conversely, does anyone know how exactly one turns off automatic driver installation (and prompt with the wizard)? Thanks a lot.

  Read the article

• Package problems after upgrade

  - by Dan

  I installed a new upgrade on ubuntu which seemed to fail near the end. Now I'm being told that an error has occurred and to please run apt-get to see what's wrong. After some further tries with that I eventually gave up. It seems there's a left over latex package(?) somewhere and I can't seem to get rid of or fix it. Here's an example: blank@ubuntu:~$ sudo apt-get dist-upgrade Reading package lists... Done Building dependency tree Reading state information... Done You might want to run 'apt-get -f install' to correct these. The following packages have unmet dependencies: tex-common : Breaks: texlive-common (< 2010) but 2009-15 is installed texlive-base : Depends: texlive-binaries (>= 2012.20120516) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-doc-base : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-extra-utils : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed texlive-font-utils : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-generic-recommended : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-latex-base : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-latex-base-doc : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-latex-extra : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-latex-extra-doc : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-latex-recommended : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-latex-recommended-doc : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-luatex : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-pictures : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-pictures-doc : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-pstricks : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-pstricks-doc : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed zlib1g : Breaks: texlive-binaries (< 2009-12) but 2009-11ubuntu2 is installed zlib1g:i386 : Breaks: texlive-binaries (< 2009-12) but 2009-11ubuntu2 is installed E: Unmet dependencies. Try using -f. I've seen similar errors on the site here, but not close enough that i could get it fixed. Any help would be great, Thanks

  Read the article

• XCP Project Kronos syslog error: "irq ... : nobody cared" on Dom0 host

  - by Vlad Fedin

  One of our production clusters driven by XCP suddenly went uresponsive. After restart and some investigation we found such logs in dom0 machine syslog: Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659040] irq 339: nobody cared (try booting with the "irqpoll" option) Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659058] Pid: 0, comm: swapper/3 Tainted: G C O 3.2.0-24-generic #37-Ubuntu Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659060] Call Trace: Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659062] <IRQ> [<ffffffff810db37d>] __report_bad_irq+0x3d/0xe0 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659071] [<ffffffff810db605>] note_interrupt+0x135/0x190 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659074] [<ffffffff810d8e69>] handle_irq_event_percpu+0xa9/0x220 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659078] [<ffffffff8130ff3b>] ? radix_tree_lookup+0xb/0x10 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659081] [<ffffffff810d9031>] handle_irq_event+0x51/0x80 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659084] [<ffffffff810dc187>] handle_edge_irq+0x87/0x140 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659089] [<ffffffff813a8829>] __xen_evtchn_do_upcall+0x199/0x250 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659092] [<ffffffff813aa96f>] xen_evtchn_do_upcall+0x2f/0x50 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659096] [<ffffffff81666d3e>] xen_do_hypervisor_callback+0x1e/0x30 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659097] <EOI> [<ffffffff810013aa>] ? hypercall_page+0x3aa/0x1000 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659104] [<ffffffff810013aa>] ? hypercall_page+0x3aa/0x1000 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659107] [<ffffffff8100a1d0>] ? xen_safe_halt+0x10/0x20 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659110] [<fff IRQ 339 in cat /proc/interrupts: 339: ... xen-pirq-msi-x eth0 where eth0 is hardware NIC. While host machine seems to hang, guest machines continue to work, so our tiny internal monitoring on one of the virtual hosts logged something like that: [2012-10-26 20:31:51] [OK......] 200 OK : 113159149 ns [2012-10-26 20:32:40] [DISASTER] 500 Can't connect to [hostname]:80 (No route to host) : 47763284432 ns ... [2012-10-26 20:34:40] [DISASTER] 500 Can't connect to [hostname]:80 (No route to host) : 46894835070 ns [2012-10-26 20:34:57] [DISASTER] 500 Can't connect to [hostname]:80 (Bad hostname) : 16821741955 ns ... [2012-10-26 20:38:18] [DISASTER] 500 Can't connect to [hostname]:80 (Bad hostname) : 20103298289 ns [2012-10-26 20:38:37] [DISASTER] 500 Can't connect to [hostname]:80 (Bad hostname) : 17895754943 ns Host and guest OS: Ubuntu 12.04 LTS, 05:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection Subsystem: ASUSTeK Computer Inc. Device 8369 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+ Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at fe500000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at e000 [size=32] Region 3: Memory at fe520000 (32-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: e1000e Kernel modules: e1000e Any hints how to debug this?

  Read the article

• Nagios core Event Handler not working

  - by sivashanmugam

  Nagios Event Handler is not triggering when the service is taking more time to response or down. My configuration in below nagios.cfg enable_event_handlers=1 localhost.cfg define service { use generic-service host_name Server service_description test-server servicegroups test-service check_command check-service is_volatile 0 check_period 24x7 max_check_attempts 4 normal_check_interval 2 retry_check_interval 2 contact_groups testcontacts notification_period 24x7 notification_options w,u,c,r notifications_enabled 1 event_handler_enabled 1 event_handler recheck-service } command.cfg define command{ command_name recheck-service command_line /usr/local/nagios/libexec/alert.sh $SERVICESTATE$ $SERVICESTATETYPE$ $SERVICEATTEMPT$ } alert.sh file !/bin/sh set -x case "$1" in OK) # The service just came back up, so don't do anything... ;; WARNING) # We don't really care about warning states, since the service is probably still running... ;; UNKNOWN) # We don't know what might be causing an unknown error, so don't do anything... ;; CRITICAL) Aha! The HTTP service appears to have a problem - perhaps we should restart the server... Is this a "soft" or a "hard" state? case "$2" in We're in a "soft" state, meaning that Nagios is in the middle of retrying the check before it turns into a "hard" state and contacts get notified... SOFT) # What check attempt are we on? We don't want to restart the web server on the first check, because it may just be a fluke! case "$3" in Wait until the check has been tried 3 times before restarting the web server. If the check fails on the 4th time (after we restart the web server), the state type will turn to "hard" and contacts will be notified of the problem. Hopefully this will restart the web server successfully, so the 4th check will result in a "soft" recovery. If that happens no one gets notified because we fixed the problem! 3) echo -n "Going To Ping the Virtual Machine (3rd soft critical state)..." # Call the init script to restart the HTTPD server myresult=`/usr/local/nagios/libexec/check_http xyz.com -t 100 | grep 'time'| awk '{print $10}'` echo "Your Service Is taking the following time Delay" "$myresult Seconds" |mail -s "WARNING : Service Taken More Time To Response" [email protected] ;; esac ;; # The HTTP service somehow managed to turn into a hard error without getting fixed. # It should have been restarted by the code above, but for some reason it didn't. # Let's give it one last try, shall we? # Note: Contacts have already been notified of a problem with the service at this

  Read the article

• Recognizing Dell EquilLogic with Nagios

  - by user3677595

  EDIT: All firmware and models are compatible, that is why nothing is posted about it. Okay, so there will be a lot here, so please bare with me. I've been working on this now for a few hours (reading manuals and such) so I'm not just coming here right out of the blue. I am working on a PRE-EXISTING Nagios server where there are several other existing plugins and checks running and working. Now I want to add another server there to check so I made the following modifications: First and foremost, I added a file to /usr/local/nagios/libexec named: check_equallogic.sh. The permissions are 755, the same as all others. I have chowned to nagios:nagios and in the listing it shows the Owner as Nagios. I then added a command to the commands.cfg file in \usr\local\nagios\etc\objects that shows the following: # 'check_equallogic' command definition define command{ command_name check_equallogic command_line $USER1$/check_equallogic -H $HOSTADDRESS$ -C $ARG1$ -t $ARG2$ $ARG3$ } Following this, I created a file named equallogic.cfg in the objects directory and it contains (more or less): define host{ use linux-server ; Inherit default values from a template host_name 172.16.50.11 ; The name we're giving to this device alias EqualLogic ; A longer name associated with the device address 172.16.50.11 ; IP address of the device contact_groups admins } Check Equallogic Information define service{ use generic-service host_name 172.16.50.11 service_description General Information check_command check_equallogic!public!info } After ensuring that permissions are okay for all files, I restart the nagios service, no errors. When I go into the WebGUI, I get the following errors AFTER the check runs: (Return code of 127 is out of bounds - plugin may be missing) Extra, probably unrelated problem Furthermore, when I log into the EquilLogic server, under Audit logs I get the following error: Level: AUDIT Time: 26/05/2014 3:59:13 PM Member: ps4100-1 Subsystem: agent Event ID: 22.7.1 SNMP packet validation failed, request received from 172.16.10.11 An snmpwalk receives a timeout, whereas others succeed. I will work on importing the MIBs tomorrow. The reason why I am mentioning it is because I want to make sure that it is only a MIB issue for the SNMP. If it is, then ignore this area. I am entirely unsure of what to do here.

  Read the article

• Ubuntu hardware wireless switch has no effect after suspend and 13.10 upgrade

  - by blaineh

  I'm posting this on SU after it stalled on askubuntu. I hope someone here can help! If you'd prefer to answer on AU itself, here's the link: http://askubuntu.com/questions/365177/hardware-wireless-switch-has-no-effect-after-suspend-and-13-10-upgrade Wireless works fine after a reboot, but after a suspend the hardware switch (for my laptop this is f12) has no effect on the wireless, it is just permanently off, and shows that it is with a red LED. My rfkill list all reads: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Any combination with rfkill <un>block wifi doesn't work, although one time first blocking then unblocking actually turned it on again. sudo lshw -C network reads: *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:65:2e:3f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.11.0-12-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:90100000-9010ffff *-network DISABLED description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 02 serial: c8:0a:a9:89:b4:30 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:90010000-90010fff memory:90000000-9000ffff memory:90020000-9002ffff Also, adding a /etc/pm/sleep.d/brcm.sh file as recommended here simply prevents the laptop from suspending at all, which of course is no good. This question has an answer urging to install the original driver, but it wasn't an "accepted answer" so I'd rather not take a chance on it. Also I'll admit I'm a bit lost on that and would like help doing so with the specific information I've given. I would be happy to provide more information, so long as you're willing to help me find it for you! This is a very annoying bug. I have a Compaq Presario CQ62. Edit. Output of lspci | grep Network: 02:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01) Edit. This morning, I had had the laptop suspended all night, and then when I tried to awake it, it simply wouldn't. It would try, and then it would sleep again (I guess it felt a little bit like me! </badjoke>). Is it possible these problems are related? Edit. I don't have enough reputation on SU proper to post links to pastebins and other questions I've tried, so I'm putting them in comments, and of course they're available in the original question.

  Read the article

< Previous Page | 230 231 232 233 234 235 236 237 238 239 240 241  | Next Page >