Search Results

Search found 33182 results on 1328 pages for 'linux port'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 234/1328 | < Previous Page | 230 231 232 233 234 235 236 237 238 239 240 241  | Next Page >

  • How to forward OpenVPN Port to NAT'd XEN domU

    - by John
    I want to install a OpenVPN domU on XEN. Dom0 and domU are running Debian Squeeze, all domU are on a NAT'd privat network 10.0.0.1/24 My VPN-Gate is von 10.0.0.1 and running. How can I make it accessible under the dom0 public IP? I tried forwarding the port using iptables, but without any success. Here is what i did: ~ # iptables -L -n -v Chain INPUT (policy ACCEPT 1397 packets, 118K bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 930 packets, 133K bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED PHYSDEV match --physdev-out vif5.0 0 0 ACCEPT udp -- * * 0.0.0.0/0 0.0.0.0/0 PHYSDEV match --physdev-in vif5.0 udp spt:68 dpt:67 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED PHYSDEV match --physdev-out vif5.0 0 0 ACCEPT all -- * * 10.0.0.1 0.0.0.0/0 PHYSDEV match --physdev-in vif5.0 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED PHYSDEV match --physdev-out vif3.0 0 0 ACCEPT udp -- * * 0.0.0.0/0 0.0.0.0/0 PHYSDEV match --physdev-in vif3.0 udp spt:68 dpt:67 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED PHYSDEV match --physdev-out vif3.0 0 0 ACCEPT all -- * * 10.0.0.5 0.0.0.0/0 PHYSDEV match --physdev-in vif3.0 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED PHYSDEV match --physdev-out vif2.0 0 0 ACCEPT udp -- * * 0.0.0.0/0 0.0.0.0/0 PHYSDEV match --physdev-in vif2.0 udp spt:68 dpt:67 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED PHYSDEV match --physdev-out vif2.0 0 0 ACCEPT all -- * * 10.0.0.2 0.0.0.0/0 PHYSDEV match --physdev-in vif2.0 147 8236 ACCEPT tcp -- eth0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:80 13 546 ACCEPT udp -- eth0 * 0.0.0.0/0 0.0.0.0/0 udp dpt:1194 Chain OUTPUT (policy ACCEPT 1000 packets, 99240 bytes) pkts bytes target prot opt in out source destination ~ # iptables -L -t nat -n -v Chain PREROUTING (policy ACCEPT 324 packets, 23925 bytes) pkts bytes target prot opt in out source destination 139 7824 DNAT tcp -- eth0 * 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 to:10.0.0.5:80 1 42 DNAT udp -- * * 0.0.0.0/0 0.0.0.0/0 udp dpt:1194 to:10.0.0.1:1194 Chain POSTROUTING (policy ACCEPT 92 packets, 5030 bytes) pkts bytes target prot opt in out source destination 863 64983 MASQUERADE all -- * eth0 0.0.0.0/0 0.0.0.0/0 0 0 MASQUERADE all -- * eth0 0.0.0.0/0 0.0.0.0/0 0 0 MASQUERADE all -- * eth0 0.0.0.0/0 0.0.0.0/0 Chain OUTPUT (policy ACCEPT 180 packets, 13953 bytes) pkts bytes target prot opt in out source destination

    Read the article

  • Benefits of setting a webserver in Linux

    - by John Kent
    I wonder what main purposes and benefits can one get after he sets up a webserver running on Linux installed on a VM which is hosted by Windows and that this webserver can be used as a local host for windows ? That is, I have java application that is a webserver made on Linux, I set up the virtual machine for the windows client apps to listen to its (Linux)'s local IP address and port e.g 192.168.50.50:11111 When my webserver runs, I can use http://192.168.50.50/ as the windows's localhost address (instead of 127.0.0.1 as I usually do). Thank you

    Read the article

  • Slow connection to Linux MySQL from Windows only (XAMPP)

    - by Josh
    I'm having a problem with a PHP project (using Kohana 3.2 framework) on my Windows 7 64-bit machine connecting to the database. The development database is stored on a Ubuntu Linux server on the local network. Other development machines running OSX and Linux are connecting fine. There are no other Windows development machines to test with. I can access MySQL fine using MySQL Workbench, and other projects (which I believe to be less database heavy) run mostly ok, only occasionally getting timeout messages. I'm constantly getting Maximum execution time of 30 seconds exceeded when functions such as mysql_query() are run in this particular project. Specifically, the Kohana file where the timeout occurs is MODPATH\database\classes\kohana\database\mysql.php [ 186 ]. My local set-up is: Windows 7 Professional 64bit XAMPP 1.7.7 (PHP 5.3.8) The output of uname -a of the Linux server is: Linux peach 2.6.38-11-server #50-Ubuntu SMP Mon Sep 12 21:34:27 UTC 2011 x86_64 x86_64 x86_64 GNU/Linux I've tried the following, with no success: Disabling Windows firewall Switching between using a persistant and normal connection In my.cnf, adding skip-name-resolve Increasing wait_timeout Enabling bind-address I've run out of ideas now, and have no idea how to debug an odd issue like this. Has anyone come across this before, or have any idea how I could find the root of the issue, or what might be the problem?

    Read the article

  • NTP daemon or ntpdate doesn't synchronize

    - by user2862333
    I'm having some problems with synchronization with an NTP server. 1) The NTP daemon doesn't sync the system clock at all, even though it's running (confirmed with /etc/init.d/ntp status). Forcing to sync with ntpd -q or ntpd -gq does not work either. 2) Stopping the NTP daemon and syncing manually with ntpdate does give me the following output: ~# ntpdate -d 0.debian.pool.ntp.org 6 Nov 16:48:53 ntpdate[4417]: ntpdate [email protected] Sat May 12 09:07:19 UTC 2012 (1) transmit(79.132.237.5) receive(79.132.237.5) transmit(85.234.197.2) receive(85.234.197.2) transmit(194.50.97.34) receive(194.50.97.34) transmit(79.132.237.1) receive(79.132.237.1) transmit(79.132.237.5) receive(79.132.237.5) transmit(85.234.197.2) receive(85.234.197.2) transmit(194.50.97.34) receive(194.50.97.34) transmit(79.132.237.1) receive(79.132.237.1) transmit(79.132.237.5) receive(79.132.237.5) transmit(85.234.197.2) receive(85.234.197.2) transmit(194.50.97.34) receive(194.50.97.34) transmit(79.132.237.1) receive(79.132.237.1) transmit(79.132.237.5) receive(79.132.237.5) transmit(85.234.197.2) receive(85.234.197.2) transmit(194.50.97.34) receive(194.50.97.34) transmit(79.132.237.1) receive(79.132.237.1) server 79.132.237.5, port 123 stratum 2, precision -20, leap 00, trust 000 refid [79.132.237.5], delay 0.05141, dispersion 0.00145 transmitted 4, in filter 4 reference time: d624e3b1.f490b90d Wed, Nov 6 2013 16:50:09.955 originate timestamp: d624e457.eaaf787c Wed, Nov 6 2013 16:52:55.916 transmit timestamp: d624e36c.4a7036fd Wed, Nov 6 2013 16:49:00.290 filter delay: 0.08537 0.05141 0.05151 0.06346 0.00000 0.00000 0.00000 0.00000 filter offset: 235.6038 235.6087 235.6095 235.6068 0.000000 0.000000 0.000000 0.000000 delay 0.05141, dispersion 0.00145 offset 235.608782 server 85.234.197.2, port 123 stratum 2, precision -20, leap 00, trust 000 refid [85.234.197.2], delay 0.05151, dispersion 0.00336 transmitted 4, in filter 4 reference time: d624e3e7.dc6cd02b Wed, Nov 6 2013 16:51:03.861 originate timestamp: d624e458.1c91031f Wed, Nov 6 2013 16:52:56.111 transmit timestamp: d624e36c.7da1d882 Wed, Nov 6 2013 16:49:00.490 filter delay: 0.05765 0.07750 0.06013 0.05151 0.00000 0.00000 0.00000 0.00000 filter offset: 235.6048 235.6014 235.6035 235.6078 0.000000 0.000000 0.000000 0.000000 delay 0.05151, dispersion 0.00336 offset 235.607826 server 194.50.97.34, port 123 stratum 3, precision -23, leap 00, trust 000 refid [194.50.97.34], delay 0.03021, dispersion 0.00090 transmitted 4, in filter 4 reference time: d624e38d.2bce952c Wed, Nov 6 2013 16:49:33.171 originate timestamp: d624e458.4dbbc114 Wed, Nov 6 2013 16:52:56.303 transmit timestamp: d624e36c.b0d38834 Wed, Nov 6 2013 16:49:00.690 filter delay: 0.03030 0.03636 0.03091 0.03021 0.00000 0.00000 0.00000 0.00000 filter offset: 235.6095 235.6085 235.6098 235.6105 0.000000 0.000000 0.000000 0.000000 delay 0.03021, dispersion 0.00090 offset 235.610589 server 79.132.237.1, port 123 stratum 3, precision -20, leap 00, trust 000 refid [79.132.237.1], delay 0.05113, dispersion 0.00305 transmitted 4, in filter 4 reference time: d624dfcb.6acea332 Wed, Nov 6 2013 16:33:31.417 originate timestamp: d624e458.838672ad Wed, Nov 6 2013 16:52:56.513 transmit timestamp: d624e36c.e405181c Wed, Nov 6 2013 16:49:00.890 filter delay: 0.06345 0.05113 0.05681 0.05656 0.00000 0.00000 0.00000 0.00000 filter offset: 235.6087 235.6038 235.6010 235.6074 0.000000 0.000000 0.000000 0.000000 delay 0.05113, dispersion 0.00305 offset 235.603888 6 Nov 16:49:00 ntpdate[4417]: step time server 79.132.237.5 offset 235.608782 sec Clearly, ntpdate can reach the NTP server(s), but after checking the clock, it hasn't changed and is still displaying the wrong time. Any ideas what would be the problem would be much appreciated.

    Read the article

  • bond0:0 + define virtual IP

    - by yael
    hi all in my linux server I have the follwoing: Linux Version - RedHat-Linux- 5.3.0.0 (this linux server only only one LAN) more /etc/sysconfig/network-scripts/ifcfg-bond0:0 DEVICE=bond0:0 ONBOOT=yes BOOTPROTO=static IPADDR=10.10.10.12 NETMASK=255.255.255.0 ifconfig -a bond0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) bond0:0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:10.10.10.12 Bcast:1.1.1.255 Mask:255.255.255.0 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr 00:0E:0C:C7:F8:92 inet addr:1.1.1.1 Bcast:1.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:cff:fec7:f892/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8600 errors:0 dropped:0 overruns:0 frame:0 TX packets:4764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:717979 (701.1 KiB) TX bytes:598620 (584.5 KiB) Memory:b8820000-b8840000 my problems: why I get HWaddr 00:00:00:00:00:00 and not the real MAC address I cant ping to other server with 10.10.10.11 from my server is it posible to define bond0:0 when I have only one LAN (eth0) other info: more /etc/modprobe.conf alias eth0 e1000e alias eth1 e1000e alias eth2 e1000e alias eth3 e1000e alias scsi_hostadapter mptbase alias scsi_hostadapter1 mptsas alias scsi_hostadapter2 ata_piix alias bond0 bonding alias bond1 bonding

    Read the article

  • bond0:0 + define virtual IP

    - by yael
    hi all in my linux server I have the follwoing: Linux Version - RedHat-Linux- 5.3.0.0 (this linux server only only one LAN) more /etc/sysconfig/network-scripts/ifcfg-bond0:0 DEVICE=bond0:0 ONBOOT=yes BOOTPROTO=static IPADDR=10.10.10.12 NETMASK=255.255.255.0 ifconfig -a bond0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) bond0:0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:10.10.10.12 Bcast:1.1.1.255 Mask:255.255.255.0 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr 00:0E:0C:C7:F8:92 inet addr:1.1.1.1 Bcast:1.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:cff:fec7:f892/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8600 errors:0 dropped:0 overruns:0 frame:0 TX packets:4764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:717979 (701.1 KiB) TX bytes:598620 (584.5 KiB) Memory:b8820000-b8840000 my problems: why I get HWaddr 00:00:00:00:00:00 and not the real MAC address I cant ping to other server with 10.10.10.11 from my server is it posible to define bond0:0 when I have only one LAN (eth0) other info: more /etc/modprobe.conf alias eth0 e1000e alias eth1 e1000e alias eth2 e1000e alias eth3 e1000e alias scsi_hostadapter mptbase alias scsi_hostadapter1 mptsas alias scsi_hostadapter2 ata_piix alias bond0 bonding alias bond1 bonding

    Read the article

  • bond0:0 + define virtual IP

    - by yael
    in my Linux server I have the following: Linux Version - RedHat-Linux- 5.3.0.0 (this Linux server only only one LAN) more /etc/sysconfig/network-scripts/ifcfg-bond0:0 DEVICE=bond0:0 ONBOOT=yes BOOTPROTO=static IPADDR=10.10.10.12 NETMASK=255.255.255.0 ifconfig -a bond0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) bond0:0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:10.10.10.12 Bcast:1.1.1.255 Mask:255.255.255.0 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr 00:0E:0C:C7:F8:92 inet addr:1.1.1.1 Bcast:1.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:cff:fec7:f892/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8600 errors:0 dropped:0 overruns:0 frame:0 TX packets:4764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:717979 (701.1 KiB) TX bytes:598620 (584.5 KiB) Memory:b8820000-b8840000 my problems: why I get HWaddr 00:00:00:00:00:00 and not the real MAC address I cant ping to other server with 10.10.10.11 from my server is it possible to define bond0:0 when I have only one LAN (eth0) other info: more /etc/modprobe.conf alias eth0 e1000e alias eth1 e1000e alias eth2 e1000e alias eth3 e1000e alias scsi_hostadapter mptbase alias scsi_hostadapter1 mptsas alias scsi_hostadapter2 ata_piix alias bond0 bonding alias bond1 bonding

    Read the article

  • Setting up a VPN tunnel between a Linux box and a Cisco FW

    - by Meni
    Hi. I have a linux box (ubuntu) and I have a service provider that will only allow an IPSEC tunnel connection between his network and my linux box. I have these details from the service provider: Service Provider: Peer IP – Lan on service provider's side - 10.10.10.10/24 Linux box details: Peer IP - Lan - Connection details: Phase1: Sha Aes 128 DH - group x Preshared – Lifetime – 24h Phase2: Sha Aes 128 Lifetime – 1h I am not sure which app I need to install on the linux box that will support this type of connection. Any ideas? Thanks!

    Read the article

  • Mysterious swap usage on EC2

    - by rusty
    We're in the middle of a project to move our infrastructure from a co-lo situation into Amazon EC2 and we've noticed some weird memory characteristics of the processes in our setup. Without going into too much detail about the specifics of our processes, we've noticed that on our EC2 instances "top" will show processes using a lot of swap space -- in fact, much greater than the amount of available swap or (if you add it all up) more than the available disk. Here's a sample top output: Mem: 7136868k total, 5272300k used, 1864568k free, 256876k buffers Swap: 1048572k total, 0k used, 1048572k free, 2526504k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ SWAP COMMAND 4121 jboss 20 0 5913m 603m 14m S 0.7 8.7 3:59.90 5.2g java 22730 root 20 0 2394m 4012 1976 S 2.0 0.1 4:20.57 2.3g PassengerHelper 20564 rails 20 0 2539m 220m 9828 S 0.3 3.2 0:23.58 2.3g java 1423 nscd 20 0 877m 1464 972 S 0.0 0.0 0:03.89 876m nscd You can see, for instance, that jboss is reportedly using 5.2 gigs of swap space which is definitely impossible since there's only 1G allocated and none is being used (probably because there's still 1.8G of RAM free). And here's the results of uname -a: Linux xxx.yyy.zzz 2.6.35.14-106.53.amzn1.x86_64 #1 SMP Fri Jan 6 16:20:10 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux We're running an AMI based off of the default Amazon Linux AMI (Amazon Linux AMI release 2011.09, so some RHEL5 and RHEL 6) with not too many customizations and definitely no kernel-level customizations. Something here tells me that on this particular kernel/distribution, the reporting of swap or maybe even total memory usage isn't what it appears to be... Any help would be appreciated!

    Read the article

  • haproxy backend default location

    - by magd1
    If you go to www.company.com, I want it to redirect to /something/something on my server, but the URL still shows www.company.com Is this possible in haproxy? backend new_marketing_server *** set default URL to /something/something*** mode http balance roundrobin timeout server 10m option httpclose server server1 10.86.151.142:80 minconn 32000 maxconn 3200 check port 80 inter 2000 server server2 10.122.13.189:80 minconn 32000 maxconn 3200 check port 80 inter 2000

    Read the article

  • VM: Windows 7 host, Linux guest, VT-d?

    - by chx
    I am sick of the driver issues of Linux. So I am planning to switch to Windows 7 as a host and virtualize my Linux into it. My laptop has integrated Intel graphics and supports VT-d. For speed reasons I would like to assign that card to Linux. Now, Parallels could do it but this page says Note: If you have only one PCIe video adapter, its name will be grayed out in the PCI Devices list and you will not be able to allocate it to your virtual machines. I would be perfectly fine with a headless Windows 7 (I can remotely admin from other computers or just the Linux guest) -- is there any VM software that doesn't have this restriction?

    Read the article

  • Tried to install Mint to a Flash Drive. Now I can't boot from the main hard disk.

    - by Dan
    Hello, all. I'm kind of new to Linux and I need some help. I wanted to install a Linux distro to a flash drive so that I can have a portable OS with all my settings, programs, etc. wherever I go. So I fired up a Linux Mint Live CD and installed Mint to the flash drive, and this seems to work OK. But now, whenever I try to boot up my system normally without the flash drive plugged in, it doesn't seem to work. It basically hangs for a bit, and then I get the following prompt: error: no such device: (some long hex val) grub rescue> However, when I try powering my system up when the USB is plugged into the computer, it gives me an option between using the OS installed on my USB and the OS installed on my HD. Selecting the latter, everything loads up just fine. I'm guessing that installing Mint to the flash drive somehow messed with my native Grub installation, but, again, I'm kind of new to Linux, so I'm not sure exactly why. Any help is greatly appreciated.

    Read the article

  • mysql on ubunto 4 is not running and is not remotely accessible

    - by user628119
    Currently i installed ubunot on ubunto 4.4, and using following commands i can see mysql, mysqld running ps -ef | grep mysql ps -ef | grep mysqld but when I run, netstat i don't see mysql and 3306 anywhere. in my.cnf file, i have given my ip and port is 3306. also when i run this command sudo netstat -tap | grep mysql i don't see anything and commands I needed to run the mysql 5 on port 3306 and on ip=x.x.x.x for remotely accessible Looking forward to your reply

    Read the article

  • linux vs windows and web server question

    - by student
    What are the differences from security point of view running a web server on linux and running a web server on windows. I heard that almost nobody going to attack linux machine. Is that true? or Linux is hard to attack and nobody want to waste his time?

    Read the article

  • dual boot with windows and linux

    - by nuttynibbles
    hi, i have windows xp installed. Recently i installed suse linux and afterwhich suse linux is the main OS to be booted up. However suse rovide options to boot windows 1 (window xp) during boot up. If i uninstall suse linux (i've tried), windows won't be able to be booted up as the grub master boot will be corrupted. my question is: is there a software tool which can be booted on cd to modify the master boot record so as to reduce much effort??

    Read the article

  • dual boot with windows and linux

    - by nuttynibbles
    hi, i have windows xp installed. Recently i installed suse linux and afterwhich suse linux is the main OS to be booted up. However suse rovide options to boot windows 1 (window xp) during boot up. If i uninstall suse linux (i've tried), windows won't be able to be booted up as the grub master boot will be corrupted. my question is: is there a software tool which can be booted on cd to modify the master boot record so as to reduce much effort??

    Read the article

  • Accessing the partitions on an VLM volume

    - by projix
    Suppose you have an LVM volume /dev/vg0/mylv. You have presented this as a virtual disk to a virtualised or emulated guest system. During installation the guest system sees it as /dev/sda and partitions it into /dev/sda{1,2,5,6} and completes the installation. Now at some point you need to access those filesystems from within the host system, without running the guest system. fdisk sees these partitions just fine: # fdisk -l /dev/vg0/mylv Device Boot Start End Blocks Id System /dev/vg0/mylv1 2048 684031 340992 83 Linux /dev/vg0/mylv2 686078 20969471 10141697 5 Extended /dev/vg0/mylv5 686080 8290303 3802112 83 Linux /dev/vg0/mylv6 8292352 11980799 1844224 83 Linux However, the devices such as /dev/vg0/mylv1 do not actually exist. I guess that because they're within an LV, the OS does not recognise this type of nesting by default. Is there any way I can prod Linux so that /dev/vg0/mylv1 or equivalent appears and thus becomes mountable within the host system? I understand that it's possible with qemu-nbd, and will use this if necessary. However, I was hoping for something more direct if possible, rather than simulating a network block device and attaching that.

    Read the article

  • Changing externally visible IP on a multi-IP router?

    - by AlternateZ
    I work at a public library and I'm trying to configure OCLC's EzProxy software. I've run into a problem and I think it's related to our network config. I'm punching above my weight here a little so I need some help. I think I'm trying to configure a 1:1 NAT, but not sure how or if our hardware supports it. The EzProxy machine is on an internet line which supports multiple external IPs. Our router is a Billion BiGuard30. There's another server on this line, let's say its IP is x.x.x.9. The EzProxy machine is x.x.x.11 I've set up port forwarding from x.x.x.11 on the http ports to the EzProxy machine. Trying to browse to x.x.x.11 from an external PC works fine - we get to the EzProxy page we are serving. However, if we go to something like WhatIsMyIP from the EzProxy machine, it says that its IP is x.x.x.9. This causes problems with our user authentication software. How do we make the rest of the internet see that the machine is x.x.x.11? There doesnt seem to be any "outbound port forwarding" on the Billion router, nor is there any "1:1 NAT" options in its config webpage. The EzProxy machine is running Ubuntu 12.04, if that helps.

    Read the article

  • Forward differing hostnames to different internal IPs through NAT router

    - by abrereton
    Hi, I have one public IP address, one router and multiple servers behind the router. I would like to forward differing domains (All using HTTP) through the router to different servers. For example: example1.com => 192.168.0.110 example2.com => 192.168.0.120 foo.example2.com => 192.168.0.130 bar.example2.com => 192.168.0.140 I understand that this could be accomplished using Port Forwarding, but I need all hosts running on port 80. I found some information about IP Masquerading, but I found this difficult to understand, and I am not sure if it is what I am after. Another solution I have found is to direct all traffic to Reverse Proxy server, which forwards the requests onto the appropriate server. What about iptables? I am using a Billion 7404 VNPX router. Is there a feature that this router has that can accomplish this? Are these my only options? Have I missed something completely? Is one recommended over the others? I have searched around but I don't think I am hitting the correct keywords. Thanks in advance.

    Read the article

  • Make router forward HTTP and HTTPS traffic to external App

    - by cOsticla
    I use a Linksys WRT54GL router with DD-WRT v24-sp2 (10/10/09) std (SVN revision 13064) which I am trying to make forward all HTTP and HTTPS traffic to an external app called Fiddler (used as proxy) on port 8888. After a lot of digging on this site, dd-wrt forum, dd-wrt.com and WWW, I am stacked with the following piece of code that works (thanks to the guys from dd-wrt support for this info), but only for forwarding HTTP traffic (port 80): #!/bin/sh PROXY_IP=1234567890 PROXY_PORT=8888 LAN_IP=`nvram get lan_ipaddr` LAN_NET=$LAN_IP/`nvram get lan_netmask` iptables -t nat -A PREROUTING -i br0 -s $LAN_NET -d $LAN_NET -p tcp --dport 80 -j ACCEPT iptables -t nat -A PREROUTING -i br0 -s ! $PROXY_IP -p tcp --dport 80 -j DNAT --to $PROXY_IP:$PROXY_PORT iptables -t nat -I POSTROUTING -o br0 -s $LAN_NET -d $PROXY_IP -p tcp -j SNAT --to $LAN_IP iptables -I FORWARD -i br0 -o br0 -s $LAN_NET -d $PROXY_IP -p tcp --dport $PROXY_PORT -j ACCEPT I tried to edit the code from above and I came up with the following but it's still not forwarding HTTPS but just HTTP traffic: #!/bin/sh PROXY_IP=1234567890 PROXY_PORT=8888 LAN_IP=`nvram get lan_ipaddr` LAN_NET=$LAN_IP/`nvram get lan_netmask` iptables -t nat -A PREROUTING -i br0 -s $LAN_NET -d $LAN_NET -p tcp -m multiport --dports 80,443 -j ACCEPT iptables -t nat -A PREROUTING -i br0 -s ! $PROXY_IP -p tcp -m multiport --dports 80,443 -j DNAT --to $PROXY_IP:$PROXY_PORT iptables -t nat -I POSTROUTING -o br0 -s $LAN_NET -d $PROXY_IP -p tcp -j SNAT --to $LAN_IP iptables -I FORWARD -i br0 -o br0 -s $LAN_NET -d $PROXY_IP -p tcp --dport $PROXY_PORT -j ACCEPT I am not sure if is possible to forward HTTPS traffic anymore by just using a router so I'd appreciate if somebody will share his thoughts and/or examples regarding this subject here. Thanks!

    Read the article

  • Mac Mavericks, ngircd localhost works, private IP doesn't

    - by user221945
    I have configured ngircd to listen on my private ip address. It doesn't. Localhost works fine. Configuration test: ngIRCd 21-IDENT+IPv6+IRCPLUS+SSL+SYSLOG+TCPWRAP+ZLIB-x86_64/apple/darwin13.2.0 Copyright (c)2001-2013 Alexander Barton () and Contributors. Homepage: http://ngircd.barton.de/ This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. Reading configuration from "/opt/local/etc/ngircd.conf" ... OK, press enter to see a dump of your server configuration ... [GLOBAL] Name = irc.bellbookandpistol.com AdminInfo1 = Jaedreth AdminInfo2 = San Diego County CA, US AdminEMail = [email protected] HelpFile = /opt/local/share/doc/ngircd/Commands.txt Info = Server Info Text Listen = 10.0.1.5,127.0.0.1 MotdFile = MotdPhrase = "Welcome to irc.bellbookandpistol.com" Password = PidFile = Ports = 6667 ServerGID = wheel ServerUID = root [LIMITS] ConnectRetry = 60 IdleTimeout = 0 MaxConnections = 0 MaxConnectionsIP = 6 MaxJoins = -1 MaxNickLength = 9 MaxListSize = 0 PingTimeout = 120 PongTimeout = 20 [OPTIONS] AllowedChannelTypes = #&+ AllowRemoteOper = no ChrootDir = CloakHost = CloakHostModeX = CloakHostSalt = kBih5mu\kVI!DC6eifT(hd4m/0'zb/=: CloakUserToNick = no ConnectIPv4 = yes ConnectIPv6 = no DefaultUserModes = DNS = yes IncludeDir = /opt/local/etc/ngircd.conf.d MorePrivacy = no NoticeAuth = no OperCanUseMode = no OperChanPAutoOp = yes OperServerMode = no RequireAuthPing = no ScrubCTCP = no SyslogFacility = local5 WebircPassword = [SSL] CertFile = CipherList = HIGH:!aNULL:@STRENGTH DHFile = KeyFile = KeyFilePassword = Ports = [OPERATOR] Name = [REDACTED] Password = [REDACTED] Mask = [CHANNEL] Name = #BBP Modes = tnk Key = MaxUsers = 0 Topic = Welcome to the Bell, Book and Pistol IRC Server! KeyFile = As you can see, it should be listening on 10.0.1.5, but it isn't. After turning on Apache manually, port 80 works on 10.0.1.5, but port 6667 doesn't. It only works on localhost. Is there some terminal command I could use or some config file I could edit to get this to work?

    Read the article

  • Find whether TV supports S Video

    - by Vik
    Hello Freinds I have a TV (some unknown model) which has 3 sockets to insert 3 wires red, yellow and white. A DVD Player can be connected to the TV using sockets and the TV displays that the TV is in AV mode when DVD is running. Now i have a Desktop which has a S Video Port and i have a wire to connect the S Video port from my computer to those red, yellow and white sockets using appropriate pins. Now i have searched all over the remote and it does not switches to S Video Mode, it has only 2 modes of operation i.e. 1 Cable Connection (Third Party DTH Receiver receives channels and i pay subscription) and 2 AV Mode. It does not have S Video Mode or any other mode. Now my question is whether i can connect the S Video cable from my desktop to the above described TV or i should look for a new TV if i wish to connect the S Video from Computer to TV or there is any sort of converter that can help? I did tried connecting the S Video cable from Desktop to TV, but it did'nt worked. TV kept on displaying Blue Screen of AV Mode. Regards

    Read the article

  • How can I use my cell phone to establish a dial-up networking connection?

    - by gWiz
    I am using Windows 7 and have a BlackBerry with T-Mobile (U.S.). I have paired the phone with my computer over Bluetooth, which automatically creates a serial port for it. I am able to open the port in PuTTY and successfully issue AT commands to the modem, including dialing. However, while using Windows to create and establish a Dial-Up Networking connection, I get an error dialog stating "Error 678. The remote computer did not respond." In my testing, I also tried setting up a connection to dial a number connected to a phone. When attempting to connect over this connection, the phone does ring but the very moment I answer the call, my computer displays the above error dialog. What must be done to successfully establish such a PPP connection? Some special AT initialization string perhaps? To clarify, I'm not referring to the well-described and popular technique known as "tethering," in which the remote host of the data link is the mobile service provider. I am interested specifically in establishing direct data links with remote hosts other than my mobile service provider. Think old-school landline connection to your friend's computer or BBS. Edit 1 As grawity pointed out in comments, the missing piece of the puzzle is the actual modulator that is compatible with v-series protocols, which I expected to be built into the cellphone. So far the best only software alternative I could find is this experimental project. Edit 2 Found this forum discussion today. The participants state that there is no old-school modem in the BlackBerry. Edit 3 When I place a call in PuTTY with ATD, immediately after the call is answered (and the callee is initiating the handshake) the cellphone returns OK. This is not the expected behavior for establishing a data connection. The phone should reciprocate the handshake, and upon success return CONNECT. (Alternatively it should return BUSY or NO CARRIER, but never simply OK.) Windows DUN must be interpreting this as the "Error 678" I was seeing.

    Read the article

  • Network structure --> Server 2k8r2 <--> Livebox <--> Router <--> Other PCs

    - by Yusuf
    I have a Livebox connection to the Internet and I have set up my network as follows: - Livebox <--> Win2k8R2 Server - Livebox <--> Netgear N150 Router - Router <--> Other PCs Therefore, in my LAN, - the Livebox has IP address 192.168.1.1, - the Router 192.168.1.12 (when accessed from the Livebox or the server), - the Router 10.0.0.1 (when accessed from the PCs connected to the Router), - the server 192.168.1.2, - the PCs 10.0.0.x I was using a previous configuration, which was as follows: - Livebox <--> Netgear N150 Router - Router <--> Win2k8R2 Server - Router <--> Other PCs Everything was simple, and I just had to forward all ports for incoming connection on the Livebox to the Router, and then forward the specific ports to the Server as needed (it must be however noted that any server I use is found on the Win2k8R2 server itself). In this previous configuration, the IP addresses were as follows: - Livebox 192.168.1.1 - Router 192.168.1.12 (when seen from Livebox) - Router 10.0.0.1 (when seen from server & PCs connected to it) - Server 10.0.0.2 - PCs 10.0.0.x So now of course, my port-forwarding does not work anymore since the server is not connected (directly) to the Router. What I would like to know is how do I configure the Livebox and Router to still have the features like before? From what I understand of networks (which is very limited, btw), I see these options: Make the router assign IPs like 192.168.1.x (but then I want the forwarding to be done from the router itself, is it possible?) The forwarding on the router to the server uses IP address 10.0.0.2. I could change it to 192.168.1.2 (Is that even possible, does it work?) Forward all ports from the Livebox itself to the server, and then manage them there (Is software-based port-forwarding as secure as hardware-based?)

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 230 231 232 233 234 235 236 237 238 239 240 241  | Next Page >