Search Results

Search found 17314 results on 693 pages for 'vpn setup'.

Page 234/693 | < Previous Page | 230 231 232 233 234 235 236 237 238 239 240 241  | Next Page >

• Can I have a single solid state drive and a RAID array on the same machine? [closed]

  - by jaminto

  Hi- To summarize, i'm looking to use a single solid state drive as my primary drive, and two conventional sata drives in a RAID 1 configuration for data. I am trying to install 64-bit Windows 7 onto this configuration. Is this possible? Here are the details: I built a desktop that has been running 64-bit Vista on two 500Gb in a RAID 1 array for a few years. I just purchased an Intel X25-M 80Gb Sata Solid-State Drive, and was planning on using this a my primary drive, and keeping the RAID 1 array as my data drive. I added the SSD drive and in the RAID setup, configured it as a RAID 0 array of only one disk. Then, I tried to do a clean install of windows 7 64-bit, but got stuck in the "Missing driver for CD/DVD drive" black hole of selecting driver files and Windows telling me that i don't have the appropriate driver for my hardware. The missing hardware is NOT a CD/DVD drive, since i'm installing off of my only CD/DVD drive. Plus at one point i was able to point it at a driver for my raid controller, and then my hard drives magically showed up as browsable sources for finding drivers for some other unnamed device that setup couldn't recognize. After a few hours of trying drivers (this was a very slow process) i decided to reboot and look at the BIOS settings. I'm using an ASUS M2A-VM motherboard which has an ATI SB600 RAID controller on board. I switched the "On board SATA Type" setting from "SATA" to "AHCI" thinking that since AHCI is an Intel thing, this would help. Unfortunately, this abandoned my RAID configuration, and my previously mirrored drives are showing up as separate drives when i boot into my current windows installation. Am i trying to do the impossible here? Should i just buy a separate SATA/RAID PCI card and plug the SSD into that? Any help would be greatly appreciated.

  Read the article

• Remote desktop on Mac

  - by Crystal

  I just started a job using a Mac. I also have a Mac at home. The IT dpt here does not know how to remote login to my desktop from home. They installed the Cisco VPN client and game an account for that. I think at this point I need some remote desktop software to login to my work Machine. I looked online and downloaded the free version of TeamViewer. I didn't really understand how to use it. I have my work computer's name, and was hoping that would be enough to login, but I think I am mising a piece of the puzzle. Any thoughts on how to login to my work computer? Thanks.

  Read the article

• Wireless Bridge -DHCP

  - by Usta

  I was thinking of picking up a couple of TP-Link wireless routers, and setting them to bridge. I have a sep. LAN network that would have one of them, and I'd put one on my internet connection. Would I be able to keep my current IP subnets? (255.255.255.0 and 255.0.0.0) or would I have to pull my IPs from the same IP range. (I want to keep my current DHCP servers in place) The reason I want a bridge is so that I can VPN into the internal network.

  Read the article

• Distributing Microsoft Office Template or Macro over the network

  - by zfranciscus

  We have around 400 users who use Word and we want to make their life easier by distributing templates and macros over the network. The easiest way to do this of course to setup a shared network folder and let them get the appropriate templates and macros. Of course, each user has to know where to copy these files to in their local PC, and we have to rely on constant email communication to let them know for newer version of the macro and templates. The next alternative is to ask them to configure Word to point to these network folder. But of course any disruption to the network means disruption to their work. We are thinking to setup a synchronization mechanism that downloads new templates to their local machine. We are also thinking to make this sync tool to prompt users that it will download new templates - you know just to give them visibility that they are receiving changes. We are wondering what is the best approach that people usually use in their workplaces ? Are there any specific tool that can make this task easier ?

  Read the article

• Setting up a virtual ftp directory that points to another computer

  - by AngryHacker

  I have II5 sitting on an old Windows 2000 Professional box. It has an FTP site there that allows me to access files. It works great, no problem at all. However, now I need to setup a virtual directory that points to a share on another computer on the network (running Windows XP Tablet Edition). The share requires a user name and password. The network is a simple workgroup (i don't have any domains or any of that). What is the correct procedure for that? I've tried setting a share via UNC and typing in the UserID/Password when asked. But when I finished, the virtual machine showed up as an error in the IIS Manager and couldn't access it. I mapped the share onto a drive and then tried to setup a virtual directory with this drive. Same result. Is there something simple I am missing? Would upgrading any part of the picture help at all?

  Read the article

• Is it possible to command a common router without using the web interface?

  - by MDeSchaepmeester

  Some background The internet arrangement in my student home is really weird. There is one ethernet outlet and several wifi hotspots. Either way requires a login through a web site to get internet access. This is annoying as each device needs to login seperately and with a PS3 for example, it is impossible to get connected at all since the web login procedure doesn't work. Therefore I have installed a D-Link DIR-635 router which is connected to the ethernet outlet. It has DHCP enabled so it uses NAT, but whatever it is connected to also uses NAT and I've read this should not work. A fellow student tried it with an Apple Airport but that keeps giving errors related to NAT after NAT. Anyway my setup does work so bonus points if you can clarify this. I need to login to the web site I mentioned earlier with any device, after which all devices in my LAN have connectivity. This is great. Except... In short From time to time, I lose internet connectivity and my D-Link DIR-635 router needs to do a DHCP renew. I can do this via the web interface but my life would be easier if I could just run a cmd file which tells my router to do this without all the hassle. This would setup a connection to my router and execute the proper command. I have tried googling but couldn't find much helpful stuff.

  Read the article

• How to collect figures of traffic used per-host, broken up by time and destination?

  - by Seishun

  We have a relatively small network, all PSs in one subnet. One PC with two NICs and pfSense installed works as a firewall/router. There is an OpenVPN tunnel to a remote location, created as a site-to-site connection to another pfSense box there. I have an assignment to capture, store and show (via a web interface) information on traffic generated (both incoming and outcoming) by each host on our subnet and present it in several views: megabytes per calendar hours / days / months / years (that is, not just "one month back", but "in Dec 2010" and so on); megabytes per destination: VPN to remote location / other destinations / Google Apps servers. I tried the software packages in pfSense that offer traffic montoring - but it seems they don't store the information fixed by months, instead showing the amounts of traffic generated in periods (days/months/etc) calculated from the present moment. I'm also interested in understanding what would be the best way for me to break up traffic by hosts and destinations. I'm open to all suggestions, even if they mean that I will have to understand something new to me.

  Read the article

• Seeing double-cursor in 'recursive RDP'

  - by John

  I'm using a Virtual PC VM on my PC to connect to a remote PC using RDP over a VPN. It works just fine except that in the RDP session, I often see a double mouse cursor... I get a standard mouse-arrow and the context-specific cursor such as a caret or hourglass. It's not a big problem but rather annoying and I wondered if there's any way to fix it, or at least understand where it comes from? Is it because I'm effectively running one RDP session from inside another? My host PC runs W7, my local VM runs XP, and the remote PC access using RDP is W7. Thankyou for any help.

  Read the article

• Possible to load entries into hosts.deny from text file?

  - by Tar

  I have around 96 million IP addresses that I have collected and routinely validate to be VPN providers, proxies, etc. I want these blocked. Currently, I am including the list formatted like deny ip; in nginx and that works perfectly. I want to use this list on another server, but nginx isn't an option, and I don't trust apache to handle this without slowing down. Is there a way to load this list into hosts deny via some command like aclexec or something? Are there other alternatives like setting up a DNSBL or using hosts.deny in conjunction with one?

  Read the article

• Trouble with Remote Desktop pulling through printers. Drive Redirection works, and the ports created but not the printers

  - by Windex

  I've run out of things to look into. All the support documents have been gone through and still provide no resolution. I've checked the service permissions, (sc sdshow spooler) they all match up with other systems and what is output on the support documents. I'm nearly positive that the issue can't be permissions anyway as the software requires all users to be an administrator, so all users are a local administrator. (I haven't looked into why yet but its on the list, I was just recently brought into this team and we've put procedures in place for quick recovery.) We've applied hot fixes relating to RDS and printing, though I'm not sure which ones they were. I've combed through group policy and no where is printer redirection disabled. It's setup with all default values regarding the use and redirection of printers and a quick install of W2k8 R2 shows that it works by default. This dev install was joined to the same domain, placed in the same OU, shows the same policies applied, etc, etc, etc, The server generates all the correct redirected ports but no printers are created. It will also redirect drives without issue, this would seem to rule out the usermode service that handles redirects being broken. No events are logged related to any of the events and there are no events from the TerminalServices-Printer source. There were local printers setup. I didn't think it would mattter but as I was running out of ideas I tried deleting them all with no change. The TS was configured for the software it will be running before we checked out the redirection of printers so the other team responsible to setting up new servers wants to find a fix instead of reloading a new server. I'm not sure where or what else to look for. Any ideas?

  Read the article

• Remotely port forward/launch process or a client-less remote desktop app?

  - by DC177E

  I have an XP box running Logmein at a remote location behind a linksys router, which was running well for a whole of four days, until we had a power failure. Our ISP gave us a new IP, the machine restarted, and logmein did not autorun (or, at least, it did not automatically sign in), and our service (which may or may not be a Minecraft server with non-backed-up save files) also did not run upon startup. Logmein does not register the new IP (it still displays the old one). I have a DDNS updater service, so I do know the new dynamic address. I have tried using the built in XP remote desktop service, but, as with almost all non-cloud-based remote desktop services, it requires a port forward. Thus, I would appreciate it if anyone has any ideas as to: A: Any way of accessing our router remotely to forward the remote desktop port. I've seen the Remote Management option (forwarding the setup page to port 8080), but I do not have it enabled. I've tried UPnP, but again, the setup page for our router is not forwarded. B: Any way of remotely launching a process that does not require port forwarding (or uses ports 255XX, 18XXX, or 9000.), such as a remote console service built into XP. I realize this is a near impossibility. C: A Way to remotely start logmein, and sign in, which is likely a definite impossibility. Sorry if this is too specific for Stackexchange, or if I've put it into the wrong section (is SuperUser the correct place for this?). Ideas would, again be much appreciated, as shot-in-the-dark-like this may be.

  Read the article

• How to divert traffic based on hostname using HAProxy?

  - by Bosky

  I've had some initial success with HAProxy setting up a bunch of app servers listening on various other ports. I now have another webserver listening on one port, and i'd like to what changes to make to my config to flow traffic by hostname as well. The following is the current setup, assuming: my apache webserver is running at examplecom:8001 my bunch of app servers 0.0.0.0:8081, 0.0.0.0:8082 , 0.0.0.0:8083 global log 127.0.0.1 local0 log 127.0.0.1 local1 notice maxconn 4096 debug #quiet #user haproxy #group haproxy defaults log global mode http option httplog option dontlognull retries 3 redispatch maxconn 2000 contimeout 5000 clitimeout 50000 srvtimeout 50000 listen appservers 0.0.0.0:80 mode http balance roundrobin option httpclose option forwardfor #option httpchk HEAD /check.txt HTTP/1.0 server inst1 0.0.0.0:8081 cookie server01 check inter 2000 fall 3 server inst2 0.0.0.0:8082 cookie server02 check inter 2000 fall 3 server inst3 0.0.0.0:8083 cookie server01 check inter 2000 fall 3 server inst4 0.0.0.0:8084 cookie server02 check inter 2000 fall 3 capture cookie vgnvisitor= len 32 (any other comments on the ^ setup are welcome.) Now I'd like to continue the same above, but in addition in case - if the hostname is myspecialtopleveldomain<dot>com, then would like to flow traffic to example<dot>com:8001 ~B

  Read the article

• Optimize Windows file access over network

  - by Djizeus

  At my company I frequently need to access shared files over a Windows network. These files are located on the other side of the planet, so I guess the file share goes through some kind of VPN over Internet, but I don't control this and it is supposed to be "transparent" for me. However it is extremely slow. Displaying the content of a directory in the file explorer takes about 10s. Even if over the Internet, I did not expect that retrieving a list of file names would be that long. Are there any settings to optimize this from my Windows XP workstation, or is it mostly related to the way the network is configured? The only thing I have found so far is to cache all file names, while by default only short file names are cached (http://support.microsoft.com/kb/843418).

  Read the article

• Exchange 2010 allows outside access to network files

  - by user2891127

  One of our users discovered by accident he could access our network files from his smartphone while at home. No VPN needed. He was sent an email with an internal link to a network share on his android. When he opened the email and clicked on the link, he could browse our files while at home. Looking at the access logs, the connection to the share and files he accessed came from our mail server (Exchange 2010). We have no sharepoint servers running at all, and certainly not on the Exchange server. What is this function/feature called, and is it possible to turn this function/feature off? Should I turn this off?

  Read the article

• Unable to open websites that use HTTPS on linux

  - by negai

  I have the following network configuration: My PC 192.168.1.20/24 uses 192.168.1.1/24 as a gateway. Dlink-2760U router with Local address 192.168.1.1/24 has a VPN connection open with the provider using PPTP. Whenever I'm trying to open some web-sites that has some authorization (e.g. gmail.com, coursera.org), I'm getting a request timeout. This problem is observed mostly on linux (Ubuntu 12.04 and Debian 6.0), while most of such websites work correctly on windows XP. Could you please help me diagnose the problem? Could it be related to NAT + HTTPS? Thanks

  Read the article

• Hosting company that does Linux VPS and MS SQL

  - by danielmcq

  I'm looking for hosted solutions but there are so many companies that finding the right one using a Google search is a bit overwhelming. Ideally I would like a hosting company which has following options: -Linux VPSs - Individual VPSs should be fairly cheap since I plan on putting one or two services per VPS i.e web server on one (httpd and ColdFusion), an SVN server on another, etc. -Managed MS SQL databases - My company already has data in MS SQL databases and a lot of ColdFusion code written that has MS SQL specific commands in it. -Individually purchased dedicated IP addresses -Preferably located in the North America region My plan would be to setup one Linux VPS as a gateway/firewall/VPN server and have all of my traffic routed through so that my other servers would not use of bandwidth by talking to each other. The trick is also finding a company that does Linux VPS AND MS SQL databases. Does anybody know of any hosting companies offer what I'm looking for? Let me know if I need to add more details.

  Read the article

• Routing DHCP traffic over the internet

  - by rmanna

  i'd like to know if it's possible for the internet to be between a DHCP server and the network it's "assigned" to? so basically, something like this: -------------- ------------- ------------- | DHCP Server | | DHCP | | Clients | | |-----Internet-----| Relay Agent |------| 192.168.0.* | | | | 192.168.0.1 | | | -------------- ------------- ------------- the behavior i'm seeing is that the DHCP server is offering 192.168.0.* IPs and sending them back to 192.168.0.1, which it can't reach. i tried masquerading the packets sent by the relay agent but that doesn't seem to work. from what i've been reading, this is normal behavior since the DHCP server uses the GIADDR as the destination address for its OFFERs, and not the actual source IP of the packets it receives from the relay agent. sooo, given that my DHCP server needs to be "on the other side of the internet" as depicted above, how can i get this working? are there settings for dhcpd to do this or is creating a VPN containing the DHCP server and the relay agent the only way? thanks!

  Read the article

• FDE / SSD - partition and leave some unencrypted?

  - by Web Design Hero

  Just bought a used beast of a desktop pc. The system drive is setup as a Raid 0 SSD (Intel 510 SSD Drives) with 128 each. I will probably not have to many programs beyond office and maybe Adobe CS if I spring for it, I will be keeping big data on a regular hdd. My question is about setting up TrueCrypt with my configuration. I have not previously done full disk encryption, but I feel that its probably a good idea. I have done some speed tests using file containers on the hdd and the sdd with truecrypt. While there is a huge hit with the SSDs and Truecrypt, it still outperforms the hdd on its own by a good margin, so I think i will be okay for my needs with truecrypt. I have seen in a few places that they recommend partitioning the drive and leavign some of the SSD not inside truecrypt, does this really make a difference? If so, how much should I leave? Will there be any issue in the Raid0 configuration? I am not really concerned about all the wear leveling issue, rather loose data and be secure, but since I don't need all that space neccesarily, I would like to optimize my setup for security and speed.

  Read the article

• How to configure OpenVPN server to use custom default gateway?

  - by Arenim

  I have a vpn server at address 10.1.0.2 and the server have another ip in it's network -- 10.0.0.2 in his subnet (it's a tun2socks router). But default server's gateway is NOT 10.0.0.2 (and it's ok) but another external IP. I want all the client's traffic to be forwarded through this ip address -- 10.0.0.2. Here is part of my server's config: dev tap0 server-bridge 10.1.0.1 255.255.255.0 10.1.0.50 10.1.0.100 push "route 10.0.0.0 255.255.255.0" ; now client can ping 10.0.0.2 push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 10.1.0.1" push "dhcp-option WINS 10.1.0.1" in fact i want some like push "redirect-gateway 10.0.0.2" How can I achieve this?

  Read the article

• What is the best appliance you've used?

  - by phuzion

  Post your favorite appliances or "all-in-one" programs. Whether it runs in a virtual machine, or on its own hardware, it all goes. My submission is Untangle. It's an open source network gateway (their term). Essentially, it can run a plethora of things that you may otherwise end up buying another appliance for: Web filtering logging mail spam filtering phishing monitor spyware blocking VPN You name it, it's all there. Best of all, it's mostly free. A few appliances have annual costs due to inherent licensing or subscription costs. If you are looking for a new network perimeter device, definitely check it out. The underlying OS doesn't matter, because it's the application we want to praise, not the OS beneath it.

  Read the article

• Sharing a Win7 Mappable Network Drive in Server 2008 R2

  - by Jason

  I have a ghetto windows server 2008 r2 server that I basically run as a file server. I would like to create a share that can be mapped as a network drive by a Windows 7 Pro PC. How can I do this? I've gathered that I probably need to setup a VPN network on my Server 2008 R2 box and then grant my Win7 PC access. Is there anything else I am overlooking or is there a better way to do this? I basically just want to be able to edit xml files on my Win7 PC without having to ftp them back and forth.

  Read the article

• Changing farm account in Sharepoint 2010

  - by user55709

  After changing the the farm account to a domain user account I get the following error when trying to access the Central Administration page: "Cannot connect to configuration database" After I realized the headache may not be worth it, I decided to a reinstall using the following SP user account guidelines: http://technet.microsoft.com/en-us/library/ee662513.aspx After getting everything up, I am getting an error when using the designated farm account under the Central Admin Website Manage Service Accounts: "Access denied" If it is the farm administrator, why would I not be able to manage service accounts? I am able to access the other part of the admin site. Also, when logging in with the farm account it lists me as a "system account" not the domain account which I used for log in. Am I missing something or is this normal behavior? Am I not suppose to login with the farm account? When I log in with the Setup account (also a domain account) I can access everything with no errors on the site. The only difference between the two accounts is one has local admin privileges on the Sharepoint farm server which is the setup account. if you notice those privileges are not necessary for the farm account according to the article cited.

  Read the article

• Directory service unavailiable, new hardware same settings

  - by Alex

  I'm working on a project with 2 sites connected by a VPN. Site 1 has the main server and there is a secondary server at site 2 which I am trying to replace. The current setup works perfectly however I can't for the life of me get the replacement server at site 2 up and running. I'm trying to replace like for like just upgraded hardware. I have installed the OS (all Server 2003 Standard SP2) and used exactly the same settings as the old server. I have setup Active Directory, DNS Server, DHCP Server and WINS Server configured. I have used all the same settings as the old server (except IP address and name). I can access the active directory but I can't do anything; add, edit, delete all returns "the directory service is unavaliable". No-one can login on any of the computers on site 2 and the internet is down. Plugging the old server back in and connecting it to the network rectifies the issue (so both new and old are connected at site 2), everyone can login and the internet is back (curious since the modem connects direct to the switch, and even with the new server online I can connect to the router via IP but not the net). I really don't have much experience but I've been roped into doing this because my company is too cheap to hire a real network admin. Any suggestions of where I can start to troubleshoot this, its driving me crazy and I only have a day before all the users are back on site.

  Read the article

• 8GB, but have to run Windows Xp (32 Bit). Anything I can do with the additional memory?

  - by user12889

  I ordered a new computer with 8GB RAM with the plan to run Windows 7, 64Bit. Turns out now, that I need to run a 32Bit OS (XP or 7) due to some software which does not run on 64Bit yet (not even with any of the available compatibility settings / modes). Is there anything I can do with the memory above 4GB in this scenario? I'm willing to consider creative solutions like running a hypervisor under XP that offers the memory as a RAM-Disk for swapping etc. ? The software that does not run on 64Bit is CISCO VPN (there seems to be a half-working solution for that) and CISCO IP phone / webcam integration "CISCO Unified Video Advantage" (there is apparently no solution for that).

  Read the article

• Server periodically freezing - Help Stabilizing

  - by JonDog

  We run an asp.net/sql server data collection website with a hand full of clients dumping data in and running reports. We moved to a new server (specs below) and have had issues with it freezing and having to reboot it a dozen times over the pass six months. The hosting company has mentioned possible causes (listed below) but cant give a definite answer on what is going wrong. They have offered to reconfigure how ever I like. We have benefited from having a much faster system and really dont want to get rid of the ssd's unless they are the issue. Two possible setup changes that I've talked with them about are also listed below. Any suggestions on what maybe causing the freezing issue as well as suggestion on a new setup would be great. My main questions are: Do SSD generally have problems running the OS & SQL Server on the same RAID Array? and Are the new SSD's still unrefined enough to be running in a production environment? Thanks Current: Xeon Quad Core E3-1270 3.40 Ghz 16 GB DDR3-1333 ECC SDRAM First Hard Drive: 120GB Intel SSD Second Hard Drive: 120GB Intel SSD Third Hard Drive: 120GB Intel SSD Fourth Hard Drive: 120GB Intel SSD SAS 4 Port RAID Card Windows 2012 Standard Edition - 64 Bit MSSQL 2008 Web Edition Possible Causes: Running Sql Server & OS on same RAID Array OS Software Issues Using SSD's CPU Underpowered Not enough RAM Option 1 2x Xeon Quad Core E5-2603 1.80 GHz 16 GB DDR3-1333 ECC SDRAM 1 x 240GB Intel SSD - OS 3 x 1 TB SATA HDD (7200 RPM) - SQL Server SATA 4 Port RAID Card Windows 2012 Standard Edition - 64 Bit Option 2 Dell PowerEdge E3-1270v2 3.5GHz 4 Cores 16 GB DDR3-1600 UDIMM 4 x 128 GB Samsung 840 Pro SSD Add-in H200 (SAS/SATA Controller), 4 Hard Drives - RAID 10 Windows 2012 Standard Edition - 64 Bit

  Read the article

< Previous Page | 230 231 232 233 234 235 236 237 238 239 240 241  | Next Page >