Search Results

Search found 1662 results on 67 pages for 'cisco ace'.

Page 24/67 | < Previous Page | 20 21 22 23 24 25 26 27 28 29 30 31  | Next Page >

• How can I configure a Linksys EA4500 + usb printer for network printing (without connect cloud)

  - by Larry Kyrala

  The documentation and classic firmware (2.0.37) for Cisco's Linksys EA4500 is a bit sparse on setup details. It says I can connect a USB-printer, but then goes on to try to sell "Connect Cloud" remote management software. I don't want that. I just want to know how to set this up with the existing advanced firmware. Is it possible? AFAIK, to setup a IPP or LDP printer, there is usually some kind of queue configuration on the server (i.e. the ea4500 in this case), but I can't find it in the firmware. I also have been unable to find any existing protocols from win7 or mac osx. (windows network share, IPP/LDP etc.) I'm curious if I need to have the "Storage" accounts active and connect to my router either via the local IP or router name. There's a lot of unknowns here; it would help to know how this particular router actually works.

  Read the article

• Packet logging on PIX firewall

  - by georged.id.auindex.htm

  We have a Cisco PIX 515 firewall and I would like to set up a simple logging that would give us a traffic breakdown for billing by: source destination protocol port size time PIX is plugged into Catalyst 2970 and I was told that the best thing since sliced bread for logging is to get Netflow and get Catalyst to log. My concern, however, (besides the Netflow cost) is that I really don't want to "listen" to the internal noise and all I'm interested in are the external traffic stats above for billing and analysis purposes. What would be the simplest and the easiest solution? Cheers George

  Read the article

• Trying to understand why VLANs need to be created on intermediate switches

  - by Jon Reeves

  I'm currently studying for the Cisco switching exam and having trouble understanding exactly how 802.1q tagging works. Given three daisy chained switches (A,B, and C) with trunk ports between them and VLAN 101 defined on both end switches (A and C), I'm not sure why the VLAN also needs to be defined on the middle one (B)? Note that I am not disputing that it does need to be configured, I'm just trying to understand why exactly. As I understand it, traffic from VLAN 101 on switch A will be tagged as it goes through the trunk to switch B. According to the documentation I have read, trunks will pass all VLANs by default, and the .1q tag is only removed when the frame leaves through an access port on the relevant VLAN. From this I would expect switch B to simply forward the tagged frame unchanged through the trunk to switch C. Can anyone shed some light on how switch B processes this frame and why it does not get forwarded through the other trunk ?

  Read the article

• Need to setup a RADIUS server to authenticate a Windows client to a Windows server

  - by drosenblatt

  I have a server that I have technicians who need to be able to access using shared credentials. However, doing that violates our security policy (!). I need each user to be able to authenticate using their own credentials, but the server in question has to be logged in with a certain login (these two requirements are clearly diametrically opposed). I thought that this would be a great application for a RADIUS server. I know how to setup RADIUS to go from Windows -- Cisco, but I have no idea how to use RADIUS to authenticate Windows -- Windows. Can this be done? If so, how?

  Read the article

• Cisco Spam Blocker, Iron Port, Lotus Domino, Integration Help

  - by NickToyota

  Hi serverfault universe, I work for a medium sized (roughly 200 user) company. We are attempting to intagrate our new Cisco Spam Video Blocker (ironport) device into our network so that it acts as an incoming filter then passes it off to our Lotus domino mail server. And also vise versa. The way our network is setup currently has an mx record pointing to our Domino mail SMTP incoming server which is currently setup to be an inbound gateway and filter (using symantec domino mail software). We want to replace the inbound gateway with the ironport. Our company has also invested in a pool of external IP addresses which I believe has been currently assigned to our web, email, servers. What would the proper course of action be to successfully integrate the device be? Mx record change? Replace the domino gateway completely with the ironport? We attempted to set the ironport device to the external IP of what our mx record is pointing to without much success. Any help on proper setup would be greatly appreciated.

  Read the article

• CentOS Installation on a Cisco MCS 7800

  - by William

  I'm having some problems installing CentOS 5.5 Final (i386) onto my server, a Cisco MCS 7800. The problem comes very early into the installation. When the welcome screen comes up and gives you the option on how to boot into the DVD, I'll press enter to go into the graphical installer. The screen will then have a blinking cursor in the top left of the screen and will never go away (I thought that it just might need time but I let it sit for over 5 hours). I then booted into it again and tried using Linux Text thinking it was a problem with the graphical installer. That didn't work, same problem. Then I tried a DVD of RHEL 5 and got the same problem, both graphical and Linux text. At this point I think it's a hardware problem. The server has 2GB of ECC RAM, 1 Pentium 4 CPU @ 3.06GHZ and 2 WD Hard Drives (80GB) configured for RAID 0. (There is also an option in the BIOS for what OS type and that is set to Linux.) If anyone has any idea what is going on, it would be helpful. Edit Typing "text" doesn't change a thing. Still stuck at the blinking cursor. I looked it up and it's really the same thing as typing "linux text", which as stated in the first part of my question, I've already done.

  Read the article

• Planning home network

  - by gakhov

  I'm planning to setup my home network from scratch and want to ask professional opinions or tips. My home is connected to Internet with a cable connection (100 Mb/s). The devices I would like to connect are VoIP phone (RJ-45), TV (WiFi/LAN), 3 laptops (WiFi), 2 smartphones (WiFi), an iPad (WiFi), a Kindle (WiFi), a network printer and, probably, a home media storage (WiFi/LAN). As you can see, the most load will be on WiFi connections (probably, even if TV supports WiFi it's better to connect it by LAN?). So, I need help to choose the best router (or combination of routers) to support stable connections for all these devices and minimize the total number of routers/adapters. I like how Cisco/Linksys devices were working for me in the past, so preferably (but not obligatorily) I want to setup network with their solutions. Any thoughts?

  Read the article

• Juniper SRX1400 VPN

  - by ank

  I have been trying to set up a client VPN on a Juniper SRX1400 without much success. All documentation I found from Juniper and elsewhere does a lot of other (difficult and wonderful) things other than the simple things I want to do. We already have a VPN running on CISCO PIX hardware which we need to put to rest and we pretty much like to replicate the functionality, which is: 1) client makes a request to the outside interface of the SRX1400, 2) client gets authenticated, 3) if successful, then client is assigned all the usual DHCP stuff and becomes part of the network. What privileges this DHCP assigned network has, should be configurable of course with the usual routing/filtering methods. Am I asking for too much from the SRX for this kind of thing? Should I ditch the SRX for VPN and revert to an OpenVPN solution that I had working some time back also and was amazed at the ease of configuration, functionality and features?

  Read the article

• Aironet 1200's Auto-Channel Feature: When should it be used?

  - by Josh Brower

  In our building we have around 25 1200 series Aironets, with a bit of overlap in some areas. Up until this point, we have had them deployed in alternating 1/6/11 channels, but we are wondering if we would get better performance if we used the auto-channel select feature. In looking around, I have seen comments that this feature should not be used as the WAP does a channel scan only on the radio startup, but I have not found this in any Cisco docs. Anybody have anymore information, or real-world experience with this feature? Thanks! -Josh

  Read the article

• How to get two seperate remote domain controllers with same IP to work?

  - by Mr. Mister

  Hi, I have a VPN setup between multiple locations. Between each location and the central point (me), is a trust between our domain controllers. It all works great.. A new location wants to join, but their AD controller is using an IP address that is already in use by another AD in a separate location. Neither locations can change their IP addresses, but apparently there is a NAT rule that could be used to allow communication between each AD controller? The central site has a Cisco 5510 firewall which could perform the NAT, but I am unsure of the logic behind the NAT rule. Is anyone able to explain or help out? Thanks.

  Read the article

• Does a USB to RJ-45 console cable exist?

  - by Carl Flippin

  I am aware of the RJ-45 to DB9 adapter commonly used on cisco routers to access console. I am aware of the USB to DB9 adapters to allow laptops without serial to get a serial port. I am looking for a USB to RJ-45 adapter so I don't have to chain two adapters together. I have searched everywhere but even the pre-packaged solutions seem to have the two adapters chained together. Does such a thing exist? If it doesn't is there some technical reason it cannot? It seems like a manufacturer would just have to wire the DB9 end of the USB adapter differently and it would work just fine plugged straight into the console port of the router.

  Read the article

• NetFlow Storage Calculator

  - by javano

  I am planning to deploy a NetFlow server (using NfSen/NfDump) for harvesting data from Cisco devices; Are there standard calculations or guidelines I can use to calculate my server requirements, specifically I need to plan for storage. Is there a way of knowing how much data I will collect per day for example, given N flows? Lets say one device has 10k flows per day, this is typically XYZ MBs, so I can scale this up? If not, how many flows are you guys and girls recording per day, and how much data is this generating? Hopefully we can generate an estimate from everyone else's figures! P.S. If it makes a difference, I'll be collecting from <= 50 devices max (non more than 50Mbps each).

  Read the article

• hung up troubleshooting packet discards

  - by Chris Satola

  I realize my question is generic, but hopefully someone may have some guidance for me. My network consists of Cisco switches. I am seeing a significant amount (upwards of millions of packets per day) transmit drops between two switches. One being a 3750 and the other a 3560. The peak throughput of this link is only upper 400Mbps, so it shouldn't be a bandwidth issue. At this point, I am sort of clueless where to look or what tools I can use to determine what packets are dropping and why. I can setup a SPAN port on that link and wireshark it, but I don't know if that could tell me anything. Does anyone have any suggestions? Thanks in advance.

  Read the article

• Issues with DHCP over multiple subnets

  - by Dan Monego

  I have a cisco router configured to handle multiple subnets (10.1.10.n, 10.2.10.n, etc), and an ubuntu system serving DHCP to the computers served by the router. After a restart of the DHCP, the systems on the 10.1 subnet are fine, but neither the server or the computers configured on the other subnets can see the router at 10.2.10.1 (or 10.3.10.1, or 10.4.10.1). The router can see itself at 10.2.10.1, however. The change that caused this was restarting the server, so I'm approaching it assuming the configuration error is on that end. Is that the likely issue or is there a different problem that would prevent the machines on the 10.2.10 subnet from resolving DHCP?

  Read the article

• multiple vlans routed on one nic? trunk?General? or Access?

  - by Aceth

  ok for the last week I've tried racking my head around this... I have a SRW208P with 802.1q support, and a virtual endian appliance. I would like to be able to have 3 vlans having everything routed through the endian appliance.. i.e. The Virtual server has 2 bridged NIC's to the switch. This is where I'm getting confused .. On the 8 port switch I've got the 3 vlans set up ok (all being untagged as they are not going to be vlan aware), it's the port I'm connecting the endian firewall to the switch I'm having trouble with (second nic goes to the adsl modem and NAT'd) Is it meant to be a trunk, "Genereal" or "Access" then untagged or tagged? the end goal is to have vlan traffic routing through the single NIC and have endian route vlan traffic according to the rules. Any one have any ideas on the cisco small business stuff? Thanks

  Read the article

• DHCPOFFER delay VLAN

  - by john883

  I have configured two VLANs [ 15 and 16 ] and a trunkport on a Cisco Catalyst 2960. The trunkport is connected to eth2 on a Linux server The server is configured to support VLAN's and the interfaces eth2.15 eth2.16 is configured with ip addresses on two different subnet. dhcp3-server is running on the same server and hands out IP-addresses to the VLANs. When connecting a client to a port that is configured in ex. VLAN 15 and requesting a IP-address, i experience a long delay before recieving a DHCPOFFER, around 30 seconds or so, the client needs to send a DHCPDISCOVER about five times but will always recieve a DHCPOFFER. Any suggestion why this delay is happening?

  Read the article

• Finding a private (NAT) host's IP using historic destination data

  - by l0c0b0x

  The issue: An unknown private (NAT) client is infected with malware and it's trying to access a Bot server at random times/dates. How we know about this: We receive bot traffic notices/alerts from REN-ISAC. Unfortunately, we don't receive those until the next day after it has happened. What they provide to us is: The source address (of the firewall) The destination addresses (it varies, but they're going to network subnet allocated to a German ISP) The source port (which varies--dynamic ports). Question: What would be the best approach to finding this internal host (historically) with a Cisco ASA as firewall? I'm guessing blocking anything to the destination address(es), and logging that type of traffic/access might allow me to find the source host, but I'm not sure which tool/command would be the most useful. I've seen Netflow thrown into a few responses when it comes to logging, but I'm confused with it's association of Logging, NAL, and nBAR, and how they relate to Netflow.

  Read the article

• How do ISPs/Colocation Facilities limit bandwidth for Ethernet Drops?

  - by Kyle Brandt

  I have switch providers and have run into some problems with bandwidth limitations. I have more bandwidth then before, but there are performance issues. The router is connected to a 100mBit port, but they limit it to arbitrary settings (in software I imagine). It seems when I go above the limit, the provider starts to drop packets beyond the limit (This is what they said they do as well). Is it possible the previous provider did something like queuing packets above the this limit before dropping them? Is anyone aware of not only what can be done, but what is typical? Also, is there anything I can do on my Cisco router to help this situation? It would seem I am pretty helpless if the packets are dropped before they reach my interface (The traffic that is high is inbound to my network).

  Read the article

• Provisioning SIP Phones over the internet

  - by Jorge Fernandez

  I have a few SIP Phones that are located of site and connect to my PBX over the internet to make calls. For some reason one of these phones has become unprovisioned. In my office phones get provisioned by the server via TFTP. The ones that I have off site I pre-provisioned manually before I sent them off-site (I'm in Florida the phone is in New Jersey). Whats the best way to provision these over the internet? TFTP is very insecure. Sending the plain text profiles with the SIP Account and Password over the internet is out of the question. The phones have been off-site for about 6 months without any issues. Im using Trixbox and Cisco 7940 Phones.

  Read the article

• OS X 10.8.3 + attempt to change VPN settings = no more VPN access

  - by nicole

  I am running Mountain Lion and had gotten very tired of re-entering my password at random times when using my school's VPN network (I don't know much about these, but the type is Cisco IPSec according to the setup instructions I followed a while back). In an attempt to make life easier, I followed the instructions here, but, alas, any attempt to connect with VPN was met with the message "A configuration error has occurred. Verify your settings and try connecting again" (or something along those lines.) I then tried to do the steps in the blog post in reverse and change everything back. Upon (supposedly) doing that, though, a new error message came when attempting to connect to VPN: "The negotiation with the VPN server failed. Verify the server address and try reconnecting." Now I have no idea what to do. Is there a way to reset all VPN-related things in my system so that I can follow my school's instructions and just start over?

  Read the article

• Dynamic VPN tunneling technologies

  - by Adam

  Ok, so I'm asking a more specific question this time. I'm writing a paper about Cisco's DMVPN and one of the tasks I have is to make the analysis of available network solutions which use dynamic VPN tunnels. Because the paper is about DMVPN, I have to compare those solutions to it. I know there are a lot of dynamic tunneling technologies but I'm looking for ones that can be compared to DMVPN. So the question is: are there any technologies which use dynamic VPN tunnels (not necessarily using crypto) that can be compared to DMVPN? What are those technologies?

  Read the article

• CentOS Installation on a Cisco MCS 7800

  - by William

  Hello, I'm having some problems installing CentOS 5.5 Final (i386) Onto my server, a Cisco MCS 7800. The problem comes very early into the installation. When the welcome screen comes up ans gives you the option on how to boot into the DVD, Ill press enter to go into the graphical installer. The Screen will then have a blinking cursor in the top left of the screen and will never go away (I thought that it just might need time but I let it sit for over 5 hours.) I then booted into it again and tried using Linux Text thinking it was a problem with graphical installer. That didn't work, same problem. Then I tried a DVD of RHEL 5 and got the same problem, both graphical and Linux text. At this point i think its a hardware problem. The Server has 2GB of ECC RAM, 1 Pentium 4 CPU @ 3.06GHZ and 2 WD Hard Drives (80GB) Configured for RAID 0. ( Also there is a option in the BIOS for what OS type and that is set to Linux.) If anyone has any idea what is going on, it would be helpful. ================Edit================== ooshro, typing "text" doesn't change a thing. still stuck at the blinking cursor. I looked it up and its really the same thing as typing "linux text", which as stated in the first part of my question, i've already done.

  Read the article

• Connecting office to data center via Metro-ethernet

  - by Eric

  I am installing a metro ethernet link from my office to my data center. The office will have a cisco 3750 with several vlans. The data center end will have a more complicated set up. The metro e from the office will connect to a 2960, which will have two other 2960s with a few vlans and a 2811 router connected to it for connectivity to our other environments and the internet. I am looking at implementing this by connecting the office 3750 and the data center 2960 with a dot1q trunk and doing all routing at the 2811. I will configure subinterfaces for gateways for each of the vlans on the 2811. I work for a small company and don't have much of a budget for an ideal architecture. I can post a simple diagram if needed for clarification. Is there anything I am missing here? I feel like I am forgetting something very basic and want to make sure I eliminate any boneheaded mistakes.

  Read the article

• Cisco RV042 VPN with Dynamic IPs - Remote Gateway Not Resolving

  - by Rister

  I have an existing network setup that I inherited from my predecessor. Currently there are two sites, each with a Linksys RV042 VPN router running the 1.3.12.19-tm firmware. They are currently set up with a Gateway to Gateway VPN. One site has a static IP, the other has a Dynamic IP with a hostname set up on no-ip.com. My company is looking to set up another site so I purchased another RV042 only this one was Cisco branded and it is running the latest firmware. I had assumed that I would be able to configure a vpn from our main office (the dynamic ip) to the new site with this router quite easily. However when I set up a new VPN tunnel on either device, it stays on Waiting for Connection and the Remote Gateway shows an ip address of 0.0.0.0 rather than the remote ip address. The other VPN tunnel is still working and I don't see any obvious misconfiguration on the new router. It seems that the router is not resolving the Dynamic DNS address and therefore not giving me the option to connect the VPN. Does a Gateway to Gateway VPN work with Dynamic IP addresses on each end? Are the firmware versions not compatible? Is there something I've missed?

  Read the article

• Access VirtualBox client (WinXP) from host (Linux) when client is connected to VPN

  - by hsz

  Hello ! I have a host (Ubuntu Linux) with VirtualBox on which is installed client (Windows XP). I set bridge connection for them. Host has IP 192.168.0.102 and client 192.168.0.103. On client I've installed WAMP server and on host I can access it by simply call 192.168.0.103. When I connect on client to the Cisco VPN (need access to database over VPN) I cannot access that server from host. What should I do to make it work ?

  Read the article

< Previous Page | 20 21 22 23 24 25 26 27 28 29 30 31  | Next Page >