Search Results

Search found 9602 results on 385 pages for 'disk cleanup'.

Page 24/385 | < Previous Page | 20 21 22 23 24 25 26 27 28 29 30 31  | Next Page >

  • Windows 8.1 Update 1 Disk Usage 100%

    - by Gookjin Jeong
    Background Information / Computer Specs I have a 14-inch Samsung Series 5 Ultra. Core i5 CPU, 750GB HDD, 8GB RAM, Intel HD Graphics 4000. I've had the computer for about 1.5 years with no major problems. Problem The issue appeared at the beginning of April this year, when I updated the OS to Windows 8.1 Update 1 (not from 8 to 8.1). After being on continually (except for at night, when I put it on sleep mode) for about 48 hours, the disk usage as seen by Task Manager hits 100%. When this happens, everything from opening/closing applications to typing and even bringing up the start screen by pressing the Windows key becomes extremely slow. The only way to make the disk usage decrease is to restart the computer. Then the problem repeats. I've used my current laptop (as well as my previous laptops) this way -- putting it on sleep mode at night and restarting it only when Windows needs to install updates -- for a long time. So I know the 100% disk usage is not due to the way I use the computer. The thing that causes the spike varies. Sometimes it's System, sometimes it's one of the various applications I installed (e.g. Chrome, Evernote, Spotify, Wunderlist, iTunes, etc.), and sometimes it's Antimalware Service Executable, etc. Tried Solutions I think I tried almost every solution out there for this problem: Running the check disk command (chkdsk /b /f /v /scan c:) from Admin Command Prompt Running Windows Memory Diagnostic Disabling Superfetch and Windows Search from services.msc Running "Fix problems with Windows Update" from Control Panel -- Troubleshooting Updating and rolling back the graphics driver (Intel HD 4000) Disabling "Use hardware acceleration when available" from Chrome settings Disabling Intel Rapid Storage Technology Running the SFC /SCANNOW command as recommended here Running a quick scan & a full scan from Windows Defender (no threats found) Taking the hard drive out and putting it back Refreshing the computer, from the Update and recovery -- Recovery option in Windows settings NONE of the above worked for me. I was about to give up but then noticed that one of the main culprits of the disk usage spike, as shown in the "Disk Activity" section of the Resource Monitor, was C:\System (pagefile.sys). I googled around and found that one of the recommended solutions was to disable pagefile. I then went to **Control Panel -- System and Security -- System -- Advanced system settings -- Advanced tab -- Performance settings -- Advanced tab -- "Change" under Virtual memory and discovered that the number for "Currently allocated" at the bottom was 1280MB, although the number for "Recommended" was 4533MB. I immediately changed it to 4533MB and checked my family members' computers to see what the numbers were like. All of theirs had a currently allocated space that was only slightly smaller than the recommended space. See screenshot below: This might fix the problem. I'll have to wait a couple more days.But if it doesn't, what in the world should I do next? I'm guessing the hard drive isn't failing because This computer is less than 2 years old; and Speccy says that the status of the HDD is good. Update 5/27/2014 The "4533MB" solution did not work. I had to reboot the computer about 30 minutes ago because the disk usage again hit 100%. When I opened Resource Monitor the C:\System (pagefile.sys) again was shown to be the culprit. I have now disabled pagefile entirely via the same window shown above in the screenshot. The number for "currently allocated" is now 0MB. Will update again in a couple days, or if the problem occurs again, whichever comes sooner.

    Read the article

  • Infected Win XP disk not openable on a Vista computer

    - by Retired57
    How can I read a WinXP partioned disk that is infected and shows up on a USB connection to Win Vista computer as a single partition that Vista cannot see the contents? The XP computer HDD is partioned into 4 partitions. It became infected, and all attempts to clean it have failed. Applications begin to launch, but are then shut down by the infecting agent. Using a major Anti-virus Co. boot disk (which was unable to connect to the Web, probably because the infecting agent stopped it) with virus definitions dated after the disk became infected, the resultant scan showed no infection. I bought a USB cable to connect the IDE drive to my Vista computer, but when I open Win Explorer, it sees the disk, but does not show any contents. It indicates it is a single partition that is valid. However in all the ways I have tried it does not show drive contents. Any suggestions on what to do next?

    Read the article

  • How do I free some disk space so Ubuntu will boot again?

    - by Omkant
    I have installed Windows and Ubuntu side by side. I created a 10GB partition for the Ubuntu installation. During the two months I've been using Ubuntu I have installed some software. Now it's not starting. When I boot up it says that there is no diskspace so it could not be started . What can i do now? When I boot up all I get is a black screen terminal with a $. Please help me with a command to uninstall some programs and start using Ubuntu or any other way to get rid of this message.

    Read the article

  • Virtualbox, merging snapshots and base disk

    - by Henrik
    Hi, I have a virtual machine with about 30 snapshots in branches. The current development path is 22 snapshots plus the base disk. The amount of files is seemingly having an impact now on IO and the dev laptop I'm using (don't know if it is host disk performance issues with the 140GB total size over a lot of fragments, or just the fact that it is hitting sectors distributed across a lot of files). I would like to merge the current development branch of snapshots together with the base disk, but I am unsure if the following command would produce the correct outcome. I am not able to boot this disk after the procedure completes (5-6 hours). vboxmanage clonehd "C:\VPC-Storage\.VirtualBox\Machines\CRM\Snapshots\{245b27ac-e658-470a-b978-8e62137c33b1}.vhd" "E:\crm-20100624.vhd" --format VHD --type normal Could anyone confirm if this is the correct approach or not?

    Read the article

  • using one disk as cache for others

    - by HugoRune
    Hi Given a PC with several hard drives: Is it possible to use one fast disk as a giant file cache? I.e. automatically copying frequently accessed data to that one disk, and transparently redirecting reads and writes to that disk, so that other drives would only have be accessed occassionally. (writes would have to be forwarded to the other disks after a while of course) Advantages: the other drives could be powered down most of the time; reducing power, heat, noise speed of the other drives would not matter much. cache disk could be solid state. How can I set such a system up? What OS supports these options? Is this possible at all using Windows or Linux?

    Read the article

  • How do I make an encrypted disk image on Debian?

    - by Blacklight Shining
    I'm basically looking for an equivalent to OS X's encrypted sparsebundles. The solution should have support for file ACLs and should not force me to specify a size in the beginning (the image should only take up as much space as it needs) or require root access to mount and unmount. Ideally, I should be able to set two different passwords (both for the same data), but that's not too important. (I do have root access to the machine and so can install packages and such, but I would rather not have to sudo just to mount an image.)

    Read the article

  • How do I set up disk quotas over LDAP on CentOs?

    - by Noxshun
    I've been google-ing for some time and I haven't been able to find any resources or hints on the subject. I am wondering if it is possible to do so, if so how? Any nudge in right direction will be appricated. I do know that if you download and install "Linux Quota" from source, you'll get some perl scripts which are supposed to aid with the matter. But there is as far as I know absolutely no good documentation to help you along the way. I am also running a NFS server from the same machine. Note: This is for a university assignment, so I might be totally stupid for asking this question. I am trying to explore the options. If there is a better way of solving this, please do tell. Edit: Here is a link to the site of Linux Quota. They do include a LDAP schema, so it should be possible.

    Read the article

  • A failed disk (Pay for professional service or SpinRite?)(new edit)

    - by huggie
    EDIT: After much negotiating and begging and seeing through promotion smoke screen, thanks to the nice representative who took my case, I now know that the engineer has already fixed my NTFS partition (I guess it might be a bad block in the partition table?). She told me that the problem was considered minor, and I should be able to boot normally and just copy stuff out. Whew..I'm glad I didn't agree to the NTD $16,000 deal. New question (should this be in a new thread?): is it safer to use the linux "dd" command or is it better to boot normally into Windows XP and just copy stuff out? EDIT2: Thanks to all the help. I give the best answer to Console as it's most directed related to my question. But many suggestion are helpful and informational. ---- ORIGINAL POST BELOW --- Hi, in my previous post (You don't need to read but it's at http://superuser.com/questions/48838/windows-xp-a-disk-read-error-occurred), I said that my hard disk was not booting and is showing "a disk read error occurred". I took it to a recovery professional. A representative responded today told me that the NTFS partitions have a "NTFS partition system crash". I have no idea what that means. The engineer handling my drive will not be available for contact till tomorrow. Now the company charges me NTD (New Taiwan Dollar) $16,000 to recover lost data, that's kind of a lot considering that my graduate student monthly stipend is currently NTD $32,000 (max. allowed by regulation, may be lower, may change depend on funding). Now I'm weighting in between the options. Option A: let the professional recovers it with the half of my monthly stipend. If file/directories I designated are not recovered I don't pay a penny. (other than the initial examination fee of NTD $1000 which I've already paid.) Option B: let me try SpinRite, if failed, back to Option A. I spoke to the representative at the company they recommended me not to handle it on my own (yeah of course that's what they all want to say, right?), and at the price tag the disk error is probably relatively minor and data recoverable. But the representative really did not have detailed information of the disk failure so I didn't take her recommendation readily. Though one thing I heed was that she said that what they would do is to duplicate the disk before attempting discovery, so there would be no data loss (Is this true? can't duplicating invoke further data loss?). That sounds very good to me. Or maybe a third option: Option C: Negotiate with them to pay them to duplicate the disk hopefully for a much smaller price tag. Let me try SpinRite, if failed, back to Option A. This is a difficult decision. Ultimately I want my data back, but if a cheaper way is available to achieve the same thing... Can operating with SpinRite also corrupt data in someway? I've no idea what happened to my drive. I'll attempt to contact the engineer and hope to get it clarified and make an edit here.

    Read the article

  • Force RAID to read exiled disk?

    - by user198847
    user user197015 asked on 1th of November the following question: "We have a RAID 6 array (Infortrend EonStor DS S16F) that recently had two disks fail. Immediately prior to replacing these two disks, a third, good, disk was accidentally ejected from the array. After reinserting this disk it is marked as "exiled" by the array's firmware, and so even after replacing the two failed disks with new ones the array refuses to rebuild the logical volume and remains inaccessible. Since the temporarily-ejected disk is still functional and nothing has been written to the array since it was ejected, it seems that it should theoretically be possible to recover all the data on the array, but how can we convince the array to use the data from the "exiled" disk? Thanks for any help or advice you can offer." Now I've got quite the same problem. The post has been deleted by the user, so I don#t know if he was successful. Is there anybody who can help me? Thank you!

    Read the article

  • In Linux, is it possible to get a listing of drives' disk space usage that also shows volume labels?

    - by DavidH
    I know about df, of course, but df does not output volume labels. I have 5 USB hard drives plugged into my NAS box, and would love to know which is which. Current df output: Filesystem Size Used Avail Use% Mounted on /dev/sda1 27G 2.2G 24G 9% / none 56M 476K 55M 1% /dev none 60M 0 60M 0% /dev/shm none 60M 332K 59M 1% /var/run none 60M 0 60M 0% /var/lock none 60M 0 60M 0% /lib/init/rw /dev/sde1 150G 102G 48G 68% /media/usb0 /dev/sdb1 299G 196G 103G 66% /media/usb1 /dev/sdc1 233G 183G 51G 79% /media/usb2 /dev/sdd1 233G 209G 25G 90% /media/usb3 /dev/sdf1 150G 101G 49G 68% /media/usb4

    Read the article

  • Running Windows 7 physical disk virtualized under Linux

    - by CajunLuke
    I have an existing Windows 7 installation that I'd like to virtualize under Linux. Windows boots fine on Disk A, Linux boots fine on Disk B. (Both disks are SATA.) I can mount the Windows disk when in Linux. I've tried VirtualBox and VMWare Player and neither will allow me to boot from the other disk. VirtualBox doesn't seem to have the option to do so. VMWare Player has the option to have an IDE drive exposed to the virtual environment as a SCSI disk. I've tried that, but it throws the error "Cannot connect virtual device ide1:0 because no corresponding device is available on the host." I've verified that it's pointing to the correct hard drive. I'm willing to try other virtualization products, and I'm not averse to spending a little money to get this to work. I've seen this other question, and it's not a duplicate, as I haven't gotten that far yet. I'm also interested in solutions going the other way (Linux on Windows), but that'd be lagniappe. Gory Hardware Details: Lenovo T410, 2.4 GHz Core i5 (has virtualization extensions), 4GiB RAM, 2x 320 GiB SATA HDD, one in optical bay. Fedora 14 2.6.35.10-74.fc14.x86_64, Windows 7 32-bit.

    Read the article

  • RAID1: Which disk will be mirrored?

    - by tmelen
    How does a RAID1 system determine which disk to use as the source and which disk to use as the destination when mirroring? Assume for instance the following scenario: A RAID1 array is created with two disks A and B. A is replaced by disk C, which is added to the array. Files are beeing modified as time goes by. Now B is removed and A is reinserted. Will the RAID1 system realize that A and C are out of sync? And that C is more up-to-date than A? And if not, is there a safe way to avoid the mirroring process to start immediately when disk A is inserted?

    Read the article

  • Windows 8: 100% disk active time, no actual data transferred

    - by fingerbangpalateclick
    Occasionally, like several times an hour, my hard drive will appear to lock up: Task Manager will show 100% active time with read and write speeds of 0. I can still switch between open windows, but anything that requires a disk access will stall for around a minute until the hard disk starts working properly again. It happens at apparently random intervals, and only happens in Windows 8. Not 7, nor Linux. It is probably not a problem with the disk itself: This is a relatively new hard drive, and S.M.A.R.T. is showing no errors. Only happens in Windows 8: not any other OS that has used the same partition, or different partitions. So, what is going on? How can I fix this? Note: this is a different problem then this one: Extremely high disk activity without any real usage My task manager would look similar, but Average Response Time, Read Speed, and Write Speed would all be 0.

    Read the article

  • Linux RHEL : Making disk image efficiently

    - by TheProfoundGeek
    I have a linux box having RHEL. Its disk (hda1) is having free space of about 25GB. I have an another disk (hda2) which is of 250GB having another RHEL instance, it's partitioned for 200GB. Data on the disk occupies about 21GB of data. The image of hda2 needs to be taken and restored on other disk of same specs. What is the best way to make image file of the hda2? Ideally the images size should be around 25GBs as the actual data on the disk is just 21GB. I am aware about the following two methods. Method 1 : Raw Image dd if=/dev/hda2 of=/path/to/image dd if=/path/to/image of=/dev/hda3 Question 1 : Will the above method make a gigantic image of 250GBs? Is it efficient? Method 2 : Compressed Image. dd if=/dev/hda2 | gzip > /path/to/image.gz gzip -dc /path/to/image.gz | dd of=/dev/hda2 Question 2 : I tried the method 2, its taking too long. What are the pit falls of this methods? Which of the above method id efficient and why? Is there any other Linux utility which can do the job? Third party tools are no no.

    Read the article

  • Booting Ubuntu Failure : error: attempt to read or write outside of disk 'hd0'

    - by never4getthis
    I have installed ubuntu 12.10 in a WD external harddrive (320GB). This is a complete installation, not live USB. When I plug it in my HP desktop I go to the BIOS settings and boot off the harddrive, everything work perfectly -as it should. Now this works on everysingle computer and laptop in my house (all HP) -except for ONE. My HP ProBook 4530s. When I select to boot of the USB I get the Message: error: attempt to read or write outside of disk 'hd0' Now, I have removed the hdd from my laptop and the external drive is the ONLY drive plugged in. Bellow is a picture of the screen. After the message I navigate to ls / (as shown below): After here I try to acces other folders under ls /, for example, I try to go to ls /boot to get to the grub folder. Then I get the same message as before: as shown by the image below: The only folders I can access without getting the message again are /home, /run and /usr. So how do I: Boot Ubuntu from GRUB2 (this screen) manually Set to automatically boot Ubuntu If possible an explanation for this problem Thanks!

    Read the article

  • chromium-browser usus 99,99% IO disk

    - by lars
    My favorite browser: chromium is testing my patience. For some reason it sometimes uses 99,99% of I/O. (reading 2-3MB/s) Other processes (updatedb.mlocate, [kswapd0], clementine, compiz) show the same behavior. However this problem always starts and ends with chromium. To illustrate the impact on my system: when my disk starts to spin like crazy en the led burns continiously the system is so slow that it takes about two to five minuits to switch to tty6, log in and execute "killall chromiumbrowser && killall chromium" This is way faster than starting a new terminal in X, just starting a terminal seems to heavy for compiz under these circumstances. Waiting until its over takes more than 30 minuits, if it ends at all. The exact circumstances are difficult to replicate. Several tabs have to be open, usualy 8 or more. It seems that the chance to increases when more complex sites like gmail of plugins like flash are running. Opening several new tabs at omgubunt.co.uk has the best chance to replecate this isue. I have no idea where to start looking for a solution. Any help would be greatly apreciated ubuntu 12.10 | 2GB | 2x 1.66GHz Intel | 32bit | IBM Thinkpad R60e

    Read the article

  • Is a disk/ata timeout exception dangerous?

    - by j-g-faustus
    I have a few hard drives in mdadm RAID 5 configured to go to standby after a few minutes of inactivity. (Using hdparm.conf spindown_time.) At irregular intervals I get messages like these in dmesg: [ 1840.251661] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 1840.251722] ata4.00: failed command: SMART [ 1840.251758] ata4.00: cmd b0/d5:01:06:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in [ 1840.251759] res 40/00:14:50:2e:04/00:00:02:00:00/40 Emask 0x4 (timeout) [ 1840.251858] ata4.00: status: { DRDY } [ 1840.251888] ata4: hard resetting link [ 1840.600742] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1840.601521] ata4.00: configured for UDMA/133 [ 1840.601547] ata4: EH complete [337877.713988] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [337877.714019] ata4.00: failed command: SMART [337877.714038] ata4.00: cmd b0/d5:01:06:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in [337877.714039] res 40/00:04:90:10:81/00:00:00:00:00/40 Emask 0x4 (timeout) [337877.714089] ata4.00: status: { DRDY } [337877.714107] ata4: hard resetting link [337878.063085] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [337878.063743] ata4.00: configured for UDMA/133 [337878.063764] ata4: EH complete I think the exception is caused by smartd when a drive does not wake up quickly enough. There are no issues (that I can tell) in accessing the drives normally through the file system - it takes a few seconds longer than normal when they are asleep, but there are no exceptions. Is this something I should worry about, as a potential symptom on something that could corrupt a drive over time? Or can I safely ignore it as part of normal operation? Edit: By request: smartctl -a for sdaand sde, both disks are members of the array. If ata4is the same as scsi-4 then sde is the one that gave the error above, according to /dev/disk/by-path.

    Read the article

  • Fresh install on SSD with Ubuntu and Windows Vista, using whole disk encryption for Ubuntu

    - by nategator
    I would like to do a fresh install on a OCZ Vertex Plus R2 SSD 60GB drive I purchased on the cheap. Since the AES-encryption looks like it may not work optimally for this drive, I would like to set up a dual-boot to Windows Vista (the only Windows copy I have for clean install purposes) and Ubuntu 12.04 with the best encryption scheme possible. My plan is to have Windows around just in case I need to use a program that won't work with Wine and Ubuntu as my daily OS with all of my information secured in case the laptop is ever stolen or sold. Although this setup will not provide a lot of space, I think I can squeeze both OSes and have enough for second-computer office tasks. So, my questions are: Which OS should I install first, Ubuntu or Vista? Any special considerations when partitioning the drive? How should I install Ubuntu to ensure full disk encryption for the Linux partition(s) and or my daily computing? Is there a significant performance upgrade with doing a solo install of Ubuntu instead of a dual boot setup? Will TRIM, for example, work correctly? Are there any significant security concerns with going the route of a dual-boot, other than the fact that any activity on Windows may be fully recoverable if the drive is stolen or sold? Thanks in advance!

    Read the article

  • Move SQL Server transaction log to another disk

    - by Jim Lahman
    When restoring a database backup, by default, SQL Server places the database files in the master database file directory.  In this example, that location is in L:\MSSQL10.CHTL\MSSQL\DATA as shown by the issuance of sp_helpfile   Hence, the restored files for the database CHTL_L2_DB are in the same directory     Per SQL Server best practices, the log file should be on its own disk drive so that the database and log file can operate in a sequential manner and perform optimally. The steps to move the log file is as follows: Record the location of the database files and the transaction log files Note the future destination of the transaction log file Get exclusive access to the database Detach from the database Move the log file to the new location Attach to the database Verify new location of transaction log Record the location of the database file To view the current location of the database files, use the system stored procedure, sp_helpfile 1: use chtl_l2_db 2: go 3:   4: sp_helpfile 5: go   Note the future destination of the transaction log file The future destination of the transaction log file will be located in K:\MSSQLLog   Get exclusive access to the database To get exclusive access to the database, alter the database access to single_user.  If users are still connected to the database, remove them by using with rollback immediate option.  Note:  If you had a pane connected to the database when the it is placed into single_user mode, then you will be presented with a reconnection dialog box. 1: alter database chtl_l2_db 2: set single_user with rollback immediate 3: go Detach from the database   Now detach from the database so that we can use windows explorer to move the transaction log file 1: use master 2: go 3:   4: sp_detach_db 'chtl_l2_db' 5: go   After copying the transaction log file re-attach to the database 1: use master 2: go 3:   4: sp_attach_db 'chtl_l2_db', 5: 'L:\MSSQL10.CHTL\MSSQL\DATA\CHTL_L2_DB.MDF', 6: 'K:\MSSQLLog\CHTL_L2_DB_4.LDF', 7: 'L:\MSSQL10.CHTL\MSSQL\DATA\CHTL_L2_DB_1.NDF', 8: 'L:\MSSQL10.CHTL\MSSQL\DATA\CHTL_L2_DB_2.NDF', 9: 'L:\MSSQL10.CHTL\MSSQL\DATA\CHTL_L2_DB_3.NDF' 10: GO

    Read the article

  • Screen going black, further investigation reveals healthy ram and hard disk, and several kernel oops logs

    - by Virulan
    Six days ago, I went to go take a shower, and I suspended Ubuntu as usual, to save battery life. I came back, and the screen was black. REISUB and general fiddling around did nothing. Restarted, and still had nothing on the screen. Since then, this has happened several times, and the only fix is to 1) force shut laptop, 2) take out battery, 3) hold power button, 4) put battery back in, 5) boot. I have investigated further into the matter, doing a ram test and a hard disk check. Both turned out fine, but then my attention turned towards the error messages I was receiving upon bootup, the whole "System program problem detected" dealio. I did some digging and found four kernel oops logs in my /var/crash. What I can understand of them points to two things, 1) they are connected to my suspending problems, since there are four them (I have had four suspending crashes), and they both confirm that there was a issue with waking up from suspend, and 2) the crashes might have to do with Python (possibly could be jumping to conclusions), since mentions of Python are peppered throughout the logs. At this point, I am unsure of how to continue, and I have come here for help. Is there any way I can fix this? Should I start by uploading the logs here?

    Read the article

  • Upgrading a hard disk – To repave or to migrate, that is the question

    - by guybarrette
    I recently changed my laptop hard disk from the stock 250GB 5400 drive to a 320GB 7200 drive.  And no, I didn’t bought a SSD drive because the cost is way too much right now.  At $70, my upgrade was a lot cheaper than a SSD drive.  Maybe next year. When changing a system main hard drive, one must ask himself: To repave or to migrate, that is the question.  I choose to migrate so I went to the Acronis Website to take a look at their product line.  They have a few products that could do the job.  One being Acronis Migrate Easy 7.0 and the other being Acronis True Image Home 2010.  Since True Image was just $10 more then Migrate Easy, I bought True Image. I inserted my new hard drive in a 2.5” USB enclosure, and started the migration process.  Once the data copied, I switched the drives.  The process went very smoothly and without hiccups.  Highly recommended. BTW, Acronis offers free trials so I guess that nothing can stop you from “testing” a migration  ;-) var addthis_pub="guybarrette";

    Read the article

  • Run Win7 Guest (raw disk) in Ubuntu (which was installed as Dual Boot on existing Win7)

    - by kingdango
    I installed Ubuntu 12.10 on top of Win 7 as a dual boot (awesome!). I'm hoping to use VirtualBox to run my original Win7 instance as a guest OS under Ubuntu. I found this existing question and followed the directions to no avail. I can get the VMDK file created but when I run it I just get a blank black screen with no additional information and Windows never loads. I see no HD activity or anything that would indicate it's loading. I used this command to create the VMDK file: VBoxManager internalcommands createrawvmdk -filename ~/.VirtualBox/Win7Native.vmdk -rawdisk /dev/sda3 It looks like everything was created correctly but I just get a blank screen when I run the VM. I do get this warning when I boot the VM: VirtualBox - Warning The virtual machine execution may run into and error condition as described below... The medium '/home/XXX/.VirtualBox/Win7Native.vmdk' has a logical size of 583GB but the file system the medium is located on can only handle up to 16GB in theory. We strongly recommend to put all your virtual disk images and the snapshot folder on a proper file system (e.g. etc3) with a sufficient size. ErrorId: Fat Partition Detected Severity: Warning How can I get this working?

    Read the article

< Previous Page | 20 21 22 23 24 25 26 27 28 29 30 31  | Next Page >