Search Results

Search found 2533 results on 102 pages for 'fragment identifier'.

Page 24/102 | < Previous Page | 20 21 22 23 24 25 26 27 28 29 30 31  | Next Page >

• xrandr fails when 3rd monitor has higher resolution

  - by Pi3cH

  I tried many combinations with xrandr command under lubuntu 12.04 to setup my three monitors DVI (DELL 1) left detected as HDMI1 HDMI (LG E2290) middle detected as HDMI2 VGA (DELL 2) right detected as VGA1 I can get the display with fix 1280x1024 on all the monitors. But once I setup 1280x1024 + 1920x1080 + 1280x1024, I get blank screen on all the monitors. Sometimes it throws crts fail error instead of blanking out. Anyone have similar issues? any solutions/workarounds? P.S. I can setup two monitors using 1280x1280 and 1920x1080 P.S.S. HDMI2 required at least 1920x1080 to display sharp picture. Outputs (it seems graphic card supports up to 8192x8192): xrandr Screen 0: minimum 320 x 200, current 3840 x 1024, maximum 8192 x 8192 VGA1 connected 1280x1024+2560+0 (normal left inverted right x axis y axis) 338mm x 270mm 1280x1024 60.0*+ 75.0 1152x864 75.0 1024x768 75.1 60.0 800x600 75.0 60.3 640x480 75.0 60.0 720x400 70.1 HDMI1 connected 1280x1024+0+0 (normal left inverted right x axis y axis) 376mm x 301mm 1280x1024 60.0*+ 75.0 1152x864 75.0 1024x768 75.1 60.0 800x600 75.0 60.3 640x480 75.0 60.0 720x400 70.1 HDMI2 connected 1280x1024+1280+0 (normal left inverted right x axis y axis) 477mm x 268mm 1920x1080 60.0 + 1680x1050 60.0 1280x1024 75.0 60.0* 1152x864 75.0 1024x768 75.1 60.0 800x600 75.0 60.3 640x480 75.0 60.0 720x400 70.1 DP1 disconnected (normal left inverted right x axis y axis) DP2 disconnected (normal left inverted right x axis y axis) 3 CRTs (0,1 VGA, 0,1,2 for other HDMI) xrandr --verbose VGA1 connected 1280x1024+2560+0 (0x47) normal (normal left inverted right x axis y axis) 338mm x 270mm Identifier: 0x42 Timestamp: 51324 Subpixel: unknown Gamma: 1.0:1.0:1.0 Brightness: 1.0 Clones: CRTC: 0 CRTCs: 0 1 ... HDMI1 connected 1280x1024+0+0 (0x47) normal (normal left inverted right x axis y axis) 376mm x 301mm Identifier: 0x43 Timestamp: 51324 Subpixel: unknown Gamma: 1.0:1.0:1.0 Brightness: 1.0 Clones: CRTC: 1 CRTCs: 0 1 2 ... HDMI2 connected 1280x1024+1280+0 (0x47) normal (normal left inverted right x axis y axis) 477mm x 268mm Identifier: 0x44 Timestamp: 51324 Subpixel: unknown Gamma: 1.0:1.0:1.0 Brightness: 1.0 Clones: CRTC: 2 CRTCs: 0 1 2 Below command fails: xrandr --output VGA1 --auto --output HDMI2 --auto --left-of VGA1 --output HDMI1 --auto --left-of HDMI2 Below command passes: xrandr --output VGA1 --auto --output HDMI2 --mode 1280x1024 --rate 60.0 --left-of VGA1 --output HDMI1 --auto --left-of HDMI2 Graphic card VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09)

  Read the article

• First time shadow mapping problems

  - by user1294203

  I have implemented basic shadow mapping for the first time in OpenGL using shaders and I'm facing some problems. Below you can see an example of my rendered scene: The process of the shadow mapping I'm following is that I render the scene to the framebuffer using a View Matrix from the light point of view and the projection and model matrices used for normal rendering. In the second pass, I send the above MVP matrix from the light point of view to the vertex shader which transforms the position to light space. The fragment shader does the perspective divide and changes the position to texture coordinates. Here is my vertex shader, #version 150 core uniform mat4 ModelViewMatrix; uniform mat3 NormalMatrix; uniform mat4 MVPMatrix; uniform mat4 lightMVP; uniform float scale; in vec3 in_Position; in vec3 in_Normal; in vec2 in_TexCoord; smooth out vec3 pass_Normal; smooth out vec3 pass_Position; smooth out vec2 TexCoord; smooth out vec4 lightspace_Position; void main(void){ pass_Normal = NormalMatrix * in_Normal; pass_Position = (ModelViewMatrix * vec4(scale * in_Position, 1.0)).xyz; lightspace_Position = lightMVP * vec4(scale * in_Position, 1.0); TexCoord = in_TexCoord; gl_Position = MVPMatrix * vec4(scale * in_Position, 1.0); } And my fragment shader, #version 150 core struct Light{ vec3 direction; }; uniform Light light; uniform sampler2D inSampler; uniform sampler2D inShadowMap; smooth in vec3 pass_Normal; smooth in vec3 pass_Position; smooth in vec2 TexCoord; smooth in vec4 lightspace_Position; out vec4 out_Color; float CalcShadowFactor(vec4 lightspace_Position){ vec3 ProjectionCoords = lightspace_Position.xyz / lightspace_Position.w; vec2 UVCoords; UVCoords.x = 0.5 * ProjectionCoords.x + 0.5; UVCoords.y = 0.5 * ProjectionCoords.y + 0.5; float Depth = texture(inShadowMap, UVCoords).x; if(Depth < (ProjectionCoords.z + 0.001)) return 0.5; else return 1.0; } void main(void){ vec3 Normal = normalize(pass_Normal); vec3 light_Direction = -normalize(light.direction); vec3 camera_Direction = normalize(-pass_Position); vec3 half_vector = normalize(camera_Direction + light_Direction); float diffuse = max(0.2, dot(Normal, light_Direction)); vec3 temp_Color = diffuse * vec3(1.0); float specular = max( 0.0, dot( Normal, half_vector) ); float shadowFactor = CalcShadowFactor(lightspace_Position); if(diffuse != 0 && shadowFactor > 0.5){ float fspecular = pow(specular, 128.0); temp_Color += fspecular; } out_Color = vec4(shadowFactor * texture(inSampler, TexCoord).xyz * temp_Color, 1.0); } One of the problems is self shadowing as you can see in the picture, the crate has its own shadow cast on itself. What I have tried is enabling polygon offset (i.e. glEnable(POLYGON_OFFSET_FILL), glPolygonOffset(GLfloat, GLfloat) ) but it didn't change much. As you see in the fragment shader, I have put a static offset value of 0.001 but I have to change the value depending on the distance of the light to get more desirable effects , which not very handy. I also tried using front face culling when I render to the framebuffer, that didn't change much too. The other problem is that pixels outside the Light's view frustum get shaded. The only object that is supposed to be able to cast shadows is the crate. I guess I should pick more appropriate projection and view matrices, but I'm not sure how to do that. What are some common practices, should I pick an orthographic projection? From googling around a bit, I understand that these issues are not that trivial. Does anyone have any easy to implement solutions to these problems. Could you give me some additional tips? Please ask me if you need more information on my code. Here is a comparison with and without shadow mapping of a close-up of the crate. The self-shadowing is more visible.

  Read the article

• OpenGL 3 and the Radeon HD 4850x2

  - by rotard

  A while ago, I picked up a copy of the OpenGL SuperBible fifth edition and slowly and painfully started teaching myself OpenGL the 3.3 way, after having been used to the 1.0 way from school way back when. Making things more challenging, I am primarily a .NET developer, so I was working in Mono with the OpenTK OpenGL wrapper. On my laptop, I put together a program that let the user walk around a simple landscape using a couple shaders that implemented per-vertex coloring and lighting and texture mapping. Everything was working brilliantly until I ran the same program on my desktop. Disaster! Nothing would render! I have chopped my program down to the point where the camera sits near the origin, pointing at the origin, and renders a square (technically, a triangle fan). The quad renders perfectly on my laptop, coloring, lighting, texturing and all, but the desktop renders a small distorted non-square quadrilateral that is colored incorrectly, not affected by the lights, and not textured. I suspect the graphics card is at fault, because I get the same result whether I am booted into Ubuntu 10.10 or Win XP. I did find that if I pare the vertex shader down to ONLY outputting the positional data and the fragment shader to ONLY outputting a solid color (white) the quad renders correctly. But as SOON as I start passing in color data (whether or not I use it in the fragment shader) the output from the vertex shader is distorted again. The shaders follow. I left the pre-existing code in, but commented out so you can get an idea what I was trying to do. I'm a noob at glsl so the code could probably be a lot better. My laptop is an old lenovo T61p with a Centrino (Core 2) Duo and an nVidia Quadro graphics card running Ubuntu 10.10 My desktop has an i7 with a Radeon HD 4850 x2 (single card, dual GPU) from Saphire dual booting into Ubuntu 10.10 and Windows XP. The problem occurs in both XP and Ubuntu. Can anyone see something wrong that I am missing? What is "special" about my HD 4850x2? string vertexShaderSource = @" #version 330 precision highp float; uniform mat4 projection_matrix; uniform mat4 modelview_matrix; //uniform mat4 normal_matrix; //uniform mat4 cmv_matrix; //Camera modelview. Light sources are transformed by this matrix. //uniform vec3 ambient_color; //uniform vec3 diffuse_color; //uniform vec3 diffuse_direction; in vec4 in_position; in vec4 in_color; //in vec3 in_normal; //in vec3 in_tex_coords; out vec4 varyingColor; //out vec3 varyingTexCoords; void main(void) { //Get surface normal in eye coordinates //vec4 vEyeNormal = normal_matrix * vec4(in_normal, 0); //Get vertex position in eye coordinates //vec4 vPosition4 = modelview_matrix * vec4(in_position, 0); //vec3 vPosition3 = vPosition4.xyz / vPosition4.w; //Get vector to light source in eye coordinates //vec3 lightVecNormalized = normalize(diffuse_direction); //vec3 vLightDir = normalize((cmv_matrix * vec4(lightVecNormalized, 0)).xyz); //Dot product gives us diffuse intensity //float diff = max(0.0, dot(vEyeNormal.xyz, vLightDir.xyz)); //Multiply intensity by diffuse color, force alpha to 1.0 //varyingColor.xyz = in_color * diff * diffuse_color.xyz; varyingColor = in_color; //varyingTexCoords = in_tex_coords; gl_Position = projection_matrix * modelview_matrix * in_position; }"; string fragmentShaderSource = @" #version 330 //#extension GL_EXT_gpu_shader4 : enable precision highp float; //uniform sampler2DArray colorMap; //in vec4 varyingColor; //in vec3 varyingTexCoords; out vec4 out_frag_color; void main(void) { out_frag_color = vec4(1,1,1,1); //out_frag_color = varyingColor; //out_frag_color = vec4(varyingColor, 1) * texture(colorMap, varyingTexCoords.st); //out_frag_color = vec4(varyingColor, 1) * texture(colorMap, vec3(varyingTexCoords.st, 0)); //out_frag_color = vec4(varyingColor, 1) * texture2DArray(colorMap, varyingTexCoords); }"; Note that in this code the color data is accepted but not actually used. The geometry is outputted the same (wrong) whether the fragment shader uses varyingColor or not. Only if I comment out the line varyingColor = in_color; does the geometry output correctly. Originally the shaders took in vec3 inputs, I only modified them to take vec4s while troubleshooting.

  Read the article

• Universal iPad App rejected because of launch crash that I can't reproduce

  - by Enrique R.

  Hello everyone, I'm very frustrated with this problem. After one week of waiting my universal iPad app has been rejected because "is crashing on launch on iPad running iPhone OS 3.2 and iPhone 3GS running iPhone OS 3.1.3 and Mac OS X 10.6.2." Unfortunately I can't replicate the problem, I've tested in debug and release modes and the app works just fine. I even created an ad-hoc configuration and test it in other devices and everything works fine. I should clarify that this is an update to a current iPhone application and I'm using the same distribution profile as the original iPhone app. Also, I checked everything before building the universal app following this entry: http://iphonedevelopment.blogspot.com/2010/04/converting-iphone-apps-to-universal.html Here are the crash logs that Apple sent me: Incident Identifier: 3E0D4A3B-2896-444D-BCBE-6C0CA1A66A90 CrashReporter Key: 18b5124ea5f657227c5f202a27ed707379b3e2e7 Process: Transfer [982] Path: /var/mobile/Applications/E9062465-7EA6-424C-9C61-D9DBCC7C915A/Transfer.app/Transfer Identifier: Transfer Version: ??? (???) Code Type: ARM (Native) Parent Process: launchd [1] Date/Time: 2010-05-04 15:35:57.399 -0700 OS Version: iPhone OS 3.1.3 (7E18) Report Version: 104 Exception Type: EXC_BAD_INSTRUCTION (SIGILL) Exception Codes: 0x00000001, 0x3eaa2188 Highlighted Thread: 0 Backtrace not available Unknown thread crashed with ARM Thread State: r0: 0x00002f90 r1: 0x00000000 r2: 0x385242d8 r3: 0x0000010d r4: 0x00000000 r5: 0x00000000 r6: 0x00000000 r7: 0x00000000 r8: 0x2ffffba0 r9: 0x2fffef90 r10: 0x00000000 r11: 0x00000000 ip: 0x0000000c sp: 0x2ffffba4 lr: 0x2fe08727 pc: 0x00002f94 cpsr: 0x40000010 Binary Images: 0x1000 - 0x25fff +Transfer armv7 /var/mobile/Applications/E9062465-7EA6-424C-9C61-D9DBCC7C915A/Transfer.app/Transfer 0x2fe00000 - 0x2fe24fff dyld armv7 /usr/lib/dyld .... And the one for the iPad: Incident Identifier: 3B170A28-C8E2-4018-8166-E69432A65070 CrashReporter Key: 4a0194e3f60559127faef2b014df605e4c47b981 Hardware Model: iPad1,1 Process: Transfer [533] Path: /var/mobile/Applications/400EE394-7BEE-45CA-942D-DBDC106360FF/Transfer.app/Transfer Identifier: Transfer Version: ??? (???) Code Type: ARM (Native) Parent Process: launchd [1] Date/Time: 2010-05-04 15:37:17.505 -0700 OS Version: iPhone OS 3.2 (7B367) Report Version: 104 Exception Type: 00000020 Exception Codes: 0x8badf00d Highlighted Thread: 0 Application Specific Information: com.erclab.iphone.photodownload failed to launch in time elapsed total CPU time (seconds): 1.150 (user 0.560, system 0.590), 6% CPU elapsed application CPU time (seconds): 0.150, 1% CPU Thread 0: 0 libobjc.A.dylib 0x33561996 0x33560000 + 6550 1 libobjc.A.dylib 0x33564986 0x33560000 + 18822 2 libobjc.A.dylib 0x33564cb2 0x33560000 + 19634 ... The app does not do anything other than loading a local HTML into a web view after the app it's launched so I don't understand why it says "failed to launch in time" Any help will be very much appreciated.

  Read the article

• Error Galleria IE7

  - by John the horn

  I am using galleria for my site [Minavet.ro][1] [1]: http://minavet.ro and this error comes up is IE7 Line:219079877 Char:2 Error:Expected identifier, string number code:0 url:http://minavet.ro Thx for your time I have given the images width and height and now the error is Line:222704333 Char:2 Error:Expected identifier, string number code:0 url:http://minavet.ro

  Read the article

• How to number the ls output in unix?

  - by Snehal

  I am trying to write a file with format - "id file_absolute_path" which basically lists down all the files recursively in a folder and give an identifier to each file listed like 1,2,3,4. I can get the absolute path of the files recursively using the following command: ls -d -1 $PWD/**/*/* However, I am unable to give an identifier from the output of the ls command. I am sure this can be done using awk, but can't seem to solve it.

  Read the article

• Strange compilation error - GAS3 generated class

  - by subh

  I am pretty new to GraniteDS..So far I have been able to successfully configure it to work with my remote java services as well as generate the equivalent AS3 files from my POJO's. But I am getting this strange error while building one of the classes using GAS3 [ERROR] C:\TestGDS_All\TestGDS-flex-remoteobjects\target\generated-sources\com\mycompany\TestGDS\masterdata\model\TankGradesMlBas e.as:[77,29] Syntax error: expecting identifier before use. public function set use(value:String):void { [ERROR] C:\TestGDS_All\TestGDS-flex-remoteobjects\target\generated-sources\com\mycompany\TestGDS\masterdata\model\TankGradesMlBas e.as:[77,52] Syntax error: expecting leftparen before leftbrace. public function set use(value:String):void { [ERROR] C:\TestGDS_All\TestGDS-flex-remoteobjects\target\generated-sources\com\mycompany\TestGDS\masterdata\model\TankGradesMlBas e.as:[77,52] Syntax error: expecting identifier before leftbrace. public function set use(value:String):void { [ERROR] C:\TestGDS_All\TestGDS-flex-remoteobjects\target\generated-sources\com\mycompany\TestGDS\masterdata\model\TankGradesMlBas e.as:[77,52] Syntax error: expecting rightparen before leftbrace. public function set use(value:String):void { [ERROR] C:\TestGDS_All\TestGDS-flex-remoteobjects\target\generated-sources\com\mycompany\TestGDS\masterdata\model\TankGradesMlBas e.as:[80,29] Syntax error: expecting identifier before use. public function get use():String { [ERROR] C:\TestGDS_All\TestGDS-flex-remoteobjects\target\generated-sources\com\mycompany\TestGDS\masterdata\model\TankGradesMlBas e.as:[80,42] Syntax error: expecting leftparen before leftbrace. public function get use():String { [ERROR] C:\TestGDS_All\TestGDS-flex-remoteobjects\target\generated-sources\com\mycompany\TestGDS\masterdata\model\TankGradesMlBas e.as:[80,42] Syntax error: expecting identifier before leftbrace. public function get use():String { [ERROR] C:\TestGDS_All\TestGDS-flex-remoteobjects\target\generated-sources\com\mycompany\TestGDS\masterdata\model\TankGradesMlBas e.as:[80,42] Syntax error: expecting rightparen before leftbrace. public function get use():String { The java class appears like this @Entity` @Table(name = "mmd_tank_grades_ml") @SuppressWarnings("serial") public class TankGradesMl implements Serializable { .... private String use; @Basic @Column(name = "USE", length = 45) public String getUse() { return use; } public void setUse(String use) { this.use = use; } What am I doing wrong? How to resolve this error? I tried by changing the java source variable like below private String usedFor; ---- @Basic @Column(name = "USE", length = 45) public String getUsedFor() { return usedFor; } /** * @param use * new value for use */ public void setUsedFor(String usedFor) { this.usedFor = usedFor; } and the error is gone...not sure why it was throwing exception for 'use'..too small for variable name :-)

  Read the article

• Unable to connect to OpenId Provider

  - by Ramesh V

  When I run in visual studio I am able to connect to openid provider, But if I host app in IIS ,I am not able to connect to openid provider. (I am getting error at CreateRequest) Please let me know what settings has to be done in IIS so that I can connect to the Openid Provider. Below is the error I am getting [InvalidOperationException: Sequence contains no elements] System.Linq.Enumerable.First(IEnumerable`1 source) +336 DotNetOpenAuth.OpenId.RelyingParty.OpenIdRelyingParty.CreateRequest(Identifier userSuppliedIdentifier) [ProtocolException: No OpenID endpoint found.] DotNetOpenAuth.OpenId.RelyingParty.OpenIdRelyingParty.CreateRequest(Identifier userSuppliedIdentifier)

  Read the article

• ABPeoplePicker select and return a phone number

  - by palominoz

  Under (BOOL)peoplePickerNavigationController:(ABPeoplePickerNavigationController *) peoplePicker shouldContinueAfterSelectingPerson:(ABRecordRef)person property:(ABPropertyID)property identifier:(ABMultiValueIdentifier)identifier{} is it possible to get returned the phone number or somewhat the user has clicked?

  Read the article

• provisioning profile problem?

  - by senthilmuthu

  hi, i am new to creating provisioning profile.can i use same provisioning profile for all applications(except using *, we can install one app at a time)?for example if i go bundle identifier and give my comapanyname only as com.mycompanyname(apple id).${PRODUCT_NAME:identifier},and also i set my certifate,after that will my application run in device?(without creating provisioning file for each application),i have seen like this in my friend system,how is it possible?any help please?

  Read the article

• UIVIewController not released when view is dismissed

  - by Nelson Ko

  I have a main view, mainWindow, which presents a couple of buttons. Both buttons create a new UIViewController (mapViewController), but one will start a game and the other will resume it. Both buttons are linked via StoryBoard to the same View. They are segued to modal views as I'm not using the NavigationController. So in a typical game, if a person starts a game, but then goes back to the main menu, he triggers: [self dismissViewControllerAnimated:YES completion:nil ]; to return to the main menu. I would assume the view controller is released at this point. The user resumes the game with the second button by opening another instance of mapViewController. What is happening, tho, is some touch events will trigger methods on the original instance (and write status updates to them - therefore invisible to the current view). When I put a breakpoint in the mapViewController code, I can see the instance will be one or the other (one of which should be released). I have tried putting a delegate to the mainWindow clearing the view: [self.delegate clearMapView]; where in the mainWindow - (void) clearMapView{ gameWindow = nil; } I have also tried self.view=nil; in the mapViewController. The mapViewController code contains MVC code, where the model is static. I wonder if this may prevent ARC from releasing the view. The model.m contains: static CanShieldModel *sharedInstance; + (CanShieldModel *) sharedModel { @synchronized(self) { if (!sharedInstance) sharedInstance = [[CanShieldModel alloc] init]; return sharedInstance; } return sharedInstance; } Another post which may have a lead, but so far not successful, is UIViewController not being released when popped I have in ViewDidLoad: // checks to see if app goes inactive - saves. [[NSNotificationCenter defaultCenter] addObserver:self selector:@selector(resignActive) name:UIApplicationWillResignActiveNotification object:nil]; with the corresponding in ViewDidUnload: [[NSNotificationCenter defaultCenter] removeObserver:self name:UIApplicationWillResignActiveNotification object:nil]; Does anyone have any suggestions? EDIT: - (void) prepareForSegue:(UIStoryboardSegue *)segue sender:(id)sender{ NSString *identifier = segue.identifier; if ([identifier isEqualToString: @"Start Game"]){ gameWindow = (ViewController *)[segue destinationViewController]; gameWindow.newgame=-1; gameWindow.delegate = self; } else if ([identifier isEqualToString: @"Resume Game"]){ gameWindow = (ViewController *)[segue destinationViewController]; gameWindow.newgame=0; gameWindow.delegate = self;

  Read the article

• C++ keeping a list of objects and calling a contructor through another function

  - by Nona Urbiz

  why isnt my object being created? When I do it like so, I am told error C2065: 'AllReferrals' : undeclared identifier as well as error C2228: left of '.push_back' must have class/struct/union. If I put the list initialization before the class I get error C2065: 'AllReferrals' : undeclared identifier. Thanks! #include <iostream> #include <fstream> #include <regex> #include <string> #include <list> #include <map> using namespace std; using namespace tr1; class Referral { public: string url; map<string, int> keywords; static bool submit(string url, string keyword, int occurrences) { //if(lots of things i'll later add){ Referral(url, keyword, occurrences); return true; //} //else // return false; } private: list<string> urls; Referral(string url, string keyword, int occurrences) { url = url; keywords[keyword] = occurrences; AllReferrals.push_back(this); } }; static list<Referral> AllReferrals; int main() { Referral::submit("url", "keyword", 1); cout << AllReferrals.size(); cout << "\n why does that ^^ say 0 (help me make it say one)?"; cout << "\n and how can i AllReferrals.push_back(this) from my constructor?"; cout << " When I do it like so, I am told error C2065: 'AllReferrals' : undeclared identifier"; cout << " as well as error C2228: left of '.push_back' must have class/struct/union."; cout << " If I put the list initialization before the class I get error C2065: 'AllReferrals' : undeclared identifier."; cout << "\n\n\t Thanks!"; getchar(); }

  Read the article

• Replacing text after node

  - by Andrew

  I am trying to remove the "Hide this data" from this XML which is proceeded with the qualifier type="noView" <element version="Local"> <qualifier name="Public" type="View" /> Good to go </element> <element version="Local"> <qualifier name="Public" type="noView" /> Hide this data </element> I am using this XSL <?xml version="1.0"?> <xsl:stylesheet version="1.0" xmlns:xsl="http://www.w3.org/1999/XSL/Transform"> <xsl:template match="node()|@*"> <xsl:copy> <xsl:apply-templates select="@*"/> <xsl:apply-templates/> </xsl:copy> </xsl:template> <xsl:template match="qualifier"> <xsl:call-template name="replace-noview" /> </xsl:template> <xsl:template name="replace-noview"> <xsl:param name="text" select="@type"/> <xsl:choose> <xsl:when test="contains($text, 'noView')"> <xsl:copy-of select="."/> <xsl:text>DELETED</xsl:text> </xsl:when> <xsl:otherwise> <xsl:copy-of select="."/> </xsl:otherwise> </xsl:choose> </xsl:template> The output I'm getting is <element identifier="ContactName" version="Local"> <qualifier name="Public" type="View" /> Good to go </element> <element identifier="ContactName" version="Local"> <qualifier name="Public" type="noView" />DELETED Hide this data </element> I am matching the "noView" attribute and can add the "DELETED" text. However I need to remove the follow "Hide this data" text. The output I would like is <element identifier="ContactName" version="Local"> <qualifier name="Public" type="View" /> Good to go </element> <element identifier="ContactName" version="Local"> <qualifier name="Public" type="noView" /> DELETED </element>

  Read the article

• ABPeoplePicker select and return SELECTED phone number

  - by palominoz

  Under (BOOL)peoplePickerNavigationController:(ABPeoplePickerNavigationController *) peoplePicker shouldContinueAfterSelectingPerson:(ABRecordRef)person property:(ABPropertyID)property identifier:(ABMultiValueIdentifier)identifier{} is it possible to get returned the phone number or somewhat the user has clicked?

  Read the article

• What is the difference between declaring an enum with and without 'typedef'?

  - by freitass

  The standard way of declaring an enum in C++ seems to be: enum <identifier> { <list_of_elements> }; However, I have already seen some declarations like: typedef enum { <list_of_elements> } <identifier>; What is the difference between them, if it exists? Which one is correct?

  Read the article

• identifiers in java with different versions?

  - by GK

  as we "No keyword should be used as an Identifier in java". But there will be some words like asser or enum or any other which have been added as keyword in version 1.4, 1.5 resp. So if any older version code is used to compile with new javac, what happens if that code contains these words as an identifier?

  Read the article

• Need a MYSQL query to compare two tables and only output non matching results

  - by ee12csvt

  I have two tables in my database, one contains a list of items with other information on these items. The other table is contains a list of photographs of these items. The items table gives each item a unique identifier,which is used in the photographs table to identifier which item has been photographed. I need to output a list of items that are not linked to a photograph in the second table. Any ideas on how I can do this?

  Read the article

• Ubuntu 10.04 not detecting multiple monitors

  - by user28837

  I have 2 graphics cards, the output from the lspci: 01:00.0 VGA compatible controller: ATI Technologies Inc RV770 [Radeon HD 4850] 02:00.0 VGA compatible controller: ATI Technologies Inc RV710 [Radeon HD 4350] I have one monitor connected to the 4850 and 2 connected to the 4350. However when I go into System Preferences Monitors the only monitor shown is the one connected to the 4850. Is there something I need to enable for it to be able to use the other card? How do I get this to work. Thanks. As per request: X.Org X Server 1.7.6 Release Date: 2010-03-17 X Protocol Version 11, Revision 0 Build Operating System: Linux 2.6.24-25-server i686 Ubuntu Current Operating System: Linux jeff-desktop 2.6.32-22-generic-pae #33-Ubuntu SMP Wed Apr 28 14:57:29 UTC 2010 i686 Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-22-generic-pae root=UUID=852e1013-4ed6-40fd-a462-c29087888383 ro quiet splash Build Date: 23 April 2010 05:11:50PM xorg-server 2:1.7.6-2ubuntu7 (Bryce Harrington <[email protected]>) Current version of pixman: 0.16.4 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Tue May 11 08:24:52 2010 (==) Using config file: "/etc/X11/xorg.conf" (==) Using config directory: "/usr/lib/X11/xorg.conf.d" (==) No Layout section. Using the first Screen section. (**) |-->Screen "Default Screen" (0) (**) | |-->Monitor "<default monitor>" (==) No device specified for screen "Default Screen". Using the first device section listed. (**) | |-->Device "Default Device" (==) No monitor specified for screen "Default Screen". Using a default monitor configuration. (==) Automatically adding devices (==) Automatically enabling devices (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist. Entry deleted from font path. (==) FontPath set to: /usr/share/fonts/X11/misc, /usr/share/fonts/X11/100dpi/:unscaled, /usr/share/fonts/X11/75dpi/:unscaled, /usr/share/fonts/X11/Type1, /usr/share/fonts/X11/100dpi, /usr/share/fonts/X11/75dpi, /var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType, built-ins (==) ModulePath set to "/usr/lib/xorg/extra-modules,/usr/lib/xorg/modules" (II) The server relies on udev to provide the list of input devices. If no devices become available, reconfigure udev or disable AutoAddDevices. (II) Loader magic: 0x81f0e80 (II) Module ABI versions: X.Org ANSI C Emulation: 0.4 X.Org Video Driver: 6.0 X.Org XInput driver : 7.0 X.Org Server Extension : 2.0 (++) using VT number 7 (--) PCI:*(0:1:0:0) 1002:9442:174b:e104 ATI Technologies Inc RV770 [Radeon HD 4850] rev 0, Mem @ 0xc0000000/268435456, 0xfe7e0000/65536, I/O @ 0x0000a000/256, BIOS @ 0x????????/131072 (--) PCI: (0:2:0:0) 1002:954f:1462:1618 ATI Technologies Inc RV710 [Radeon HD 4350] rev 0, Mem @ 0xd0000000/268435456, 0xfe8e0000/65536, I/O @ 0x0000b000/256, BIOS @ 0x????????/131072 (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory) (II) "extmod" will be loaded by default. (II) "dbe" will be loaded by default. (II) "glx" will be loaded. This was enabled by default and also specified in the config file. (II) "record" will be loaded by default. (II) "dri" will be loaded by default. (II) "dri2" will be loaded by default. (II) LoadModule: "glx" (II) Loading /usr/lib/xorg/extra-modules/modules/extensions/libglx.so (II) Module glx: vendor="FireGL - ATI Technologies Inc." compiled for 7.5.0, module version = 1.0.0 (II) Loading extension GLX (II) LoadModule: "extmod" (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so (II) Module extmod: vendor="X.Org Foundation" compiled for 1.7.6, module version = 1.0.0 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 2.0 (II) Loading extension MIT-SCREEN-SAVER (II) Loading extension XFree86-VidModeExtension (II) Loading extension XFree86-DGA (II) Loading extension DPMS (II) Loading extension XVideo (II) Loading extension XVideo-MotionCompensation (II) Loading extension X-Resource (II) LoadModule: "dbe" (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so (II) Module dbe: vendor="X.Org Foundation" compiled for 1.7.6, module version = 1.0.0 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 2.0 (II) Loading extension DOUBLE-BUFFER (II) LoadModule: "record" (II) Loading /usr/lib/xorg/modules/extensions/librecord.so (II) Module record: vendor="X.Org Foundation" compiled for 1.7.6, module version = 1.13.0 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 2.0 (II) Loading extension RECORD (II) LoadModule: "dri" (II) Loading /usr/lib/xorg/modules/extensions/libdri.so (II) Module dri: vendor="X.Org Foundation" compiled for 1.7.6, module version = 1.0.0 ABI class: X.Org Server Extension, version 2.0 (II) Loading extension XFree86-DRI (II) LoadModule: "dri2" (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so (II) Module dri2: vendor="X.Org Foundation" compiled for 1.7.6, module version = 1.1.0 ABI class: X.Org Server Extension, version 2.0 (II) Loading extension DRI2 (II) LoadModule: "fglrx" (II) Loading /usr/lib/xorg/extra-modules/modules/drivers/fglrx_drv.so (II) Module fglrx: vendor="FireGL - ATI Technologies Inc." compiled for 1.7.1, module version = 8.72.11 Module class: X.Org Video Driver (II) Loading sub module "fglrxdrm" (II) LoadModule: "fglrxdrm" (II) Loading /usr/lib/xorg/extra-modules/modules/linux/libfglrxdrm.so (II) Module fglrxdrm: vendor="FireGL - ATI Technologies Inc." compiled for 1.7.1, module version = 8.72.11 (II) ATI Proprietary Linux Driver Version Identifier:8.72.11 (II) ATI Proprietary Linux Driver Release Identifier: 8.723.1 (II) ATI Proprietary Linux Driver Build Date: Apr 8 2010 21:40:29 (II) Primary Device is: PCI 01@00:00:0 (WW) Falling back to old probe method for fglrx (II) Loading PCS database from /etc/ati/amdpcsdb (--) Assigning device section with no busID to primary device (WW) fglrx: No matching Device section for instance (BusID PCI:0@2:0:0) found (--) Chipset Supported AMD Graphics Processor (0x9442) found (WW) fglrx: No matching Device section for instance (BusID PCI:0@1:0:1) found (WW) fglrx: No matching Device section for instance (BusID PCI:0@2:0:1) found (**) ChipID override: 0x954F (**) Chipset Supported AMD Graphics Processor (0x954F) found (II) AMD Video driver is running on a device belonging to a group targeted for this release (II) AMD Video driver is signed (II) fglrx(0): pEnt->device->identifier=0x9428aa0 (II) pEnt->device->identifier=(nil) (II) fglrx(0): === [atiddxPreInit] === begin (II) Loading sub module "vgahw" (II) LoadModule: "vgahw" (II) Loading /usr/lib/xorg/modules/libvgahw.so (II) Module vgahw: vendor="X.Org Foundation" compiled for 1.7.6, module version = 0.1.0 ABI class: X.Org Video Driver, version 6.0 (II) fglrx(0): Creating default Display subsection in Screen section "Default Screen" for depth/fbbpp 24/32 (**) fglrx(0): Depth 24, (--) framebuffer bpp 32 (II) fglrx(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps) (==) fglrx(0): Default visual is TrueColor (==) fglrx(0): RGB weight 888 (II) fglrx(0): Using 8 bits per RGB (==) fglrx(0): Buffer Tiling is ON (II) Loading sub module "fglrxdrm" (II) LoadModule: "fglrxdrm" (II) Reloading /usr/lib/xorg/extra-modules/modules/linux/libfglrxdrm.so ukiDynamicMajor: found major device number 251 ukiDynamicMajor: found major device number 251 ukiOpenByBusid: Searching for BusID PCI:1:0:0 ukiOpenDevice: node name is /dev/ati/card0 ukiOpenDevice: open result is 10, (OK) ukiOpenByBusid: ukiOpenMinor returns 10 ukiOpenByBusid: ukiGetBusid reports PCI:2:0:0 ukiOpenDevice: node name is /dev/ati/card1 ukiOpenDevice: open result is 10, (OK) ukiOpenByBusid: ukiOpenMinor returns 10 ukiOpenByBusid: ukiGetBusid reports PCI:1:0:0 ukiDynamicMajor: found major device number 251 ukiDynamicMajor: found major device number 251 ukiOpenByBusid: Searching for BusID PCI:2:0:0 ukiOpenDevice: node name is /dev/ati/card0 ukiOpenDevice: open result is 11, (OK) ukiOpenByBusid: ukiOpenMinor returns 11 ukiOpenByBusid: ukiGetBusid reports PCI:2:0:0 (--) fglrx(0): Chipset: "ATI Radeon HD 4800 Series" (Chipset = 0x9442) (--) fglrx(0): (PciSubVendor = 0x174b, PciSubDevice = 0xe104) (==) fglrx(0): board vendor info: third party graphics adapter - NOT original ATI (--) fglrx(0): Linear framebuffer (phys) at 0xc0000000 (--) fglrx(0): MMIO registers at 0xfe7e0000 (--) fglrx(0): I/O port at 0x0000a000 (==) fglrx(0): ROM-BIOS at 0x000c0000 (II) fglrx(0): AC Adapter is used (II) fglrx(0): Primary V_BIOS segment is: 0xc000 (II) Loading sub module "vbe" (II) LoadModule: "vbe" (II) Loading /usr/lib/xorg/modules/libvbe.so (II) Module vbe: vendor="X.Org Foundation" compiled for 1.7.6, module version = 1.1.0 ABI class: X.Org Video Driver, version 6.0 (II) fglrx(0): VESA BIOS detected (II) fglrx(0): VESA VBE Version 3.0 (II) fglrx(0): VESA VBE Total Mem: 16384 kB (II) fglrx(0): VESA VBE OEM: ATI ATOMBIOS (II) fglrx(0): VESA VBE OEM Software Rev: 11.13 (II) fglrx(0): VESA VBE OEM Vendor: (C) 1988-2005, ATI Technologies Inc. (II) fglrx(0): VESA VBE OEM Product: RV770 (II) fglrx(0): VESA VBE OEM Product Rev: 01.00 (II) fglrx(0): ATI Video BIOS revision 9 or later detected (--) fglrx(0): Video RAM: 524288 kByte, Type: GDDR3 (II) fglrx(0): PCIE card detected (--) fglrx(0): Using per-process page tables (PPPT) as GART. (WW) fglrx(0): board is an unknown third party board, chipset is supported (--) fglrx(0): Chipset: "ATI Radeon HD 4300/4500 Series" (Chipset = 0x954f) (--) fglrx(0): (PciSubVendor = 0x1462, PciSubDevice = 0x1618) (==) fglrx(0): board vendor info: third party graphics adapter - NOT original ATI (--) fglrx(0): Linear framebuffer (phys) at 0xd0000000 (--) fglrx(0): MMIO registers at 0xfe8e0000 (--) fglrx(0): I/O port at 0x0000b000 (==) fglrx(0): ROM-BIOS at 0x000c0000 (II) fglrx(0): AC Adapter is used (II) fglrx(0): Invalid ATI BIOS from int10, the adapter is not VGA-enabled (II) fglrx(0): ATI Video BIOS revision 9 or later detected (--) fglrx(0): Video RAM: 524288 kByte, Type: DDR2 (II) fglrx(0): PCIE card detected (--) fglrx(0): Using per-process page tables (PPPT) as GART. (WW) fglrx(0): board is an unknown third party board, chipset is supported (II) fglrx(0): Using adapter: 1:0.0. (II) fglrx(0): [FB] MC range(MCFBBase = 0xf00000000, MCFBSize = 0x20000000) (II) fglrx(0): Interrupt handler installed at IRQ 31. (II) fglrx(0): Using adapter: 2:0.0. (II) fglrx(0): [FB] MC range(MCFBBase = 0xf00000000, MCFBSize = 0x20000000) (II) fglrx(0): RandR 1.2 support is enabled! (II) fglrx(0): RandR 1.2 rotation support is enabled! (==) fglrx(0): Center Mode is disabled (II) Loading sub module "fb" (II) LoadModule: "fb" (II) Loading /usr/lib/xorg/modules/libfb.so (II) Module fb: vendor="X.Org Foundation" compiled for 1.7.6, module version = 1.0.0 ABI class: X.Org ANSI C Emulation, version 0.4 (II) Loading sub module "ddc" (II) LoadModule: "ddc" (II) Module "ddc" already built-in (II) fglrx(0): Finished Initialize PPLIB! (II) Loading sub module "ddc" (II) LoadModule: "ddc" (II) Module "ddc" already built-in (II) fglrx(0): Connected Display0: DFP on external TMDS [tmds2] (II) fglrx(0): Display0 EDID data --------------------------- (II) fglrx(0): Manufacturer: DEL Model: a038 Serial#: 810829397 (II) fglrx(0): Year: 2008 Week: 51 (II) fglrx(0): EDID Version: 1.3 (II) fglrx(0): Digital Display Input (II) fglrx(0): Max Image Size [cm]: horiz.: 53 vert.: 30 (II) fglrx(0): Gamma: 2.20 (II) fglrx(0): DPMS capabilities: StandBy Suspend Off (II) fglrx(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 (II) fglrx(0): Default color space is primary color space (II) fglrx(0): First detailed timing is preferred mode (II) fglrx(0): redX: 0.640 redY: 0.330 greenX: 0.300 greenY: 0.600 (II) fglrx(0): blueX: 0.150 blueY: 0.060 whiteX: 0.312 whiteY: 0.329 (II) fglrx(0): Supported established timings: (II) fglrx(0): 720x400@70Hz (II) fglrx(0): 640x480@60Hz (II) fglrx(0): 640x480@75Hz (II) fglrx(0): 800x600@60Hz (II) fglrx(0): 800x600@75Hz (II) fglrx(0): 1024x768@60Hz (II) fglrx(0): 1024x768@75Hz (II) fglrx(0): 1280x1024@75Hz (II) fglrx(0): Manufacturer's mask: 0 (II) fglrx(0): Supported standard timings: (II) fglrx(0): #0: hsize: 1152 vsize 864 refresh: 75 vid: 20337 (II) fglrx(0): #1: hsize: 1280 vsize 1024 refresh: 60 vid: 32897 (II) fglrx(0): #2: hsize: 1920 vsize 1080 refresh: 60 vid: 49361 (II) fglrx(0): Supported detailed timing: (II) fglrx(0): clock: 148.5 MHz Image Size: 531 x 298 mm (II) fglrx(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0 (II) fglrx(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0 (II) fglrx(0): Serial No: Y183D8CF0TFU (II) fglrx(0): Monitor name: DELL S2409W (II) fglrx(0): Ranges: V min: 50 V max: 76 Hz, H min: 30 H max: 83 kHz, PixClock max 170 MHz (II) fglrx(0): EDID (in hex): (II) fglrx(0): 00ffffffffffff0010ac38a055465430 (II) fglrx(0): 3312010380351e78eeee91a3544c9926 (II) fglrx(0): 0f5054a54b00714f8180d1c001010101 (II) fglrx(0): 010101010101023a801871382d40582c (II) fglrx(0): 4500132a2100001e000000ff00593138 (II) fglrx(0): 3344384346305446550a000000fc0044 (II) fglrx(0): 454c4c205332343039570a20000000fd (II) fglrx(0): 00324c1e5311000a2020202020200059 (II) fglrx(0): End of Display0 EDID data -------------------- (II) fglrx(0): Output DFP2 has no monitor section (II) fglrx(0): Output DFP_EXTTMDS has no monitor section (II) fglrx(0): Output CRT1 has no monitor section (II) fglrx(0): Output CRT2 has no monitor section (II) fglrx(0): Output DFP2 disconnected (II) fglrx(0): Output DFP_EXTTMDS connected (II) fglrx(0): Output CRT1 disconnected (II) fglrx(0): Output CRT2 disconnected (II) fglrx(0): Using exact sizes for initial modes (II) fglrx(0): Output DFP_EXTTMDS using initial mode 1920x1080 (II) fglrx(0): DPI set to (96, 96) (II) fglrx(0): Adapter ATI Radeon HD 4800 Series has 2 configurable heads and 1 displays connected. (==) fglrx(0): QBS disabled (==) fglrx(0): PseudoColor visuals disabled (II) Loading sub module "ramdac" (II) LoadModule: "ramdac" (II) Module "ramdac" already built-in (==) fglrx(0): NoAccel = NO (==) fglrx(0): NoDRI = NO (==) fglrx(0): Capabilities: 0x00000000 (==) fglrx(0): CapabilitiesEx: 0x00000000 (==) fglrx(0): OpenGL ClientDriverName: "fglrx_dri.so" (==) fglrx(0): UseFastTLS=0 (==) fglrx(0): BlockSignalsOnLock=1 (--) Depth 24 pixmap format is 32 bpp (II) Loading extension ATIFGLRXDRI (II) fglrx(0): doing swlDriScreenInit (II) fglrx(0): swlDriScreenInit for fglrx driver ukiDynamicMajor: found major device number 251 ukiDynamicMajor: found major device number 251 ukiDynamicMajor: found major device number 251 ukiOpenByBusid: Searching for BusID PCI:1:0:0 ukiOpenDevice: node name is /dev/ati/card0 ukiOpenDevice: open result is 17, (OK) ukiOpenByBusid: ukiOpenMinor returns 17 ukiOpenByBusid: ukiGetBusid reports PCI:2:0:0 ukiOpenDevice: node name is /dev/ati/card1 ukiOpenDevice: open result is 17, (OK) ukiOpenByBusid: ukiOpenMinor returns 17 ukiOpenByBusid: ukiGetBusid reports PCI:1:0:0 (II) fglrx(0): [uki] DRM interface version 1.0 (II) fglrx(0): [uki] created "fglrx" driver at busid "PCI:1:0:0" (II) fglrx(0): [uki] added 8192 byte SAREA at 0x2000 (II) fglrx(0): [uki] mapped SAREA 0x2000 to 0xb6996000 (II) fglrx(0): [uki] framebuffer handle = 0x3000 (II) fglrx(0): [uki] added 1 reserved context for kernel (II) fglrx(0): swlDriScreenInit done (II) fglrx(0): Kernel Module Version Information: (II) fglrx(0): Name: fglrx (II) fglrx(0): Version: 8.72.11 (II) fglrx(0): Date: Apr 8 2010 (II) fglrx(0): Desc: ATI FireGL DRM kernel module (II) fglrx(0): Kernel Module version matches driver. (II) fglrx(0): Kernel Module Build Time Information: (II) fglrx(0): Build-Kernel UTS_RELEASE: 2.6.32-22-generic-pae (II) fglrx(0): Build-Kernel MODVERSIONS: yes (II) fglrx(0): Build-Kernel __SMP__: yes (II) fglrx(0): Build-Kernel PAGE_SIZE: 0x1000 (II) fglrx(0): [uki] register handle = 0x00004000 (II) fglrx(0): DRI initialization successfull! (II) fglrx(0): FBADPhys: 0xf00000000 FBMappedSize: 0x01068000 (II) fglrx(0): FBMM initialized for area (0,0)-(1920,2240) (II) fglrx(0): FBMM auto alloc for area (0,0)-(1920,1920) (front color buffer - assumption) (II) fglrx(0): Largest offscreen area available: 1920 x 320 (==) fglrx(0): Backing store disabled (II) Loading extension FGLRXEXTENSION (==) fglrx(0): DPMS enabled (II) fglrx(0): Initialized in-driver Xinerama extension (**) fglrx(0): Textured Video is enabled. (II) LoadModule: "glesx" (II) Loading /usr/lib/xorg/extra-modules/modules/glesx.so (II) Module glesx: vendor="X.Org Foundation" compiled for 1.7.1, module version = 1.0.0 (II) Loading extension GLESX (II) Loading sub module "xaa" (II) LoadModule: "xaa" (II) Loading /usr/lib/xorg/modules/libxaa.so (II) Module xaa: vendor="X.Org Foundation" compiled for 1.7.6, module version = 1.2.1 ABI class: X.Org Video Driver, version 6.0 (II) fglrx(0): GLESX enableFlags = 94 (II) fglrx(0): Using XFree86 Acceleration Architecture (XAA) Screen to screen bit blits Solid filled rectangles Solid Horizontal and Vertical Lines Driver provided ScreenToScreenBitBlt replacement Driver provided FillSolidRects replacement (II) fglrx(0): GLESX is enabled (II) LoadModule: "amdxmm" (II) Loading /usr/lib/xorg/extra-modules/modules/amdxmm.so (II) Module amdxmm: vendor="X.Org Foundation" compiled for 1.7.1, module version = 1.0.0 (II) Loading extension AMDXVOPL (II) fglrx(0): UVD2 feature is available (II) fglrx(0): Enable composite support successfully (II) fglrx(0): X context handle = 0x1 (II) fglrx(0): [DRI] installation complete (==) fglrx(0): Silken mouse enabled (==) fglrx(0): Using HW cursor of display infrastructure! (II) fglrx(0): Disabling in-server RandR and enabling in-driver RandR 1.2. (--) RandR disabled (II) Found 2 VGA devices: arbiter wrapping enabled (II) Initializing built-in extension Generic Event Extension (II) Initializing built-in extension SHAPE (II) Initializing built-in extension MIT-SHM (II) Initializing built-in extension XInputExtension (II) Initializing built-in extension XTEST (II) Initializing built-in extension BIG-REQUESTS (II) Initializing built-in extension SYNC (II) Initializing built-in extension XKEYBOARD (II) Initializing built-in extension XC-MISC (II) Initializing built-in extension SECURITY (II) Initializing built-in extension XINERAMA (II) Initializing built-in extension XFIXES (II) Initializing built-in extension RENDER (II) Initializing built-in extension RANDR (II) Initializing built-in extension COMPOSITE (II) Initializing built-in extension DAMAGE ukiDynamicMajor: found major device number 251 ukiDynamicMajor: found major device number 251 ukiOpenByBusid: Searching for BusID PCI:1:0:0 ukiOpenDevice: node name is /dev/ati/card0 ukiOpenDevice: open result is 18, (OK) ukiOpenByBusid: ukiOpenMinor returns 18 ukiOpenByBusid: ukiGetBusid reports PCI:2:0:0 ukiOpenDevice: node name is /dev/ati/card1 ukiOpenDevice: open result is 18, (OK) ukiOpenByBusid: ukiOpenMinor returns 18 ukiOpenByBusid: ukiGetBusid reports PCI:1:0:0 (II) AIGLX: Loaded and initialized /usr/lib/dri/fglrx_dri.so (II) GLX: Initialized DRI GL provider for screen 0 (II) fglrx(0): Enable the clock gating! (II) fglrx(0): Setting screen physical size to 507 x 285 (II) XKB: reuse xkmfile /var/lib/xkb/server-B20D7FC79C7F597315E3E501AEF10E0D866E8E92.xkm (II) config/udev: Adding input device Power Button (/dev/input/event1) (**) Power Button: Applying InputClass "evdev keyboard catchall" (II) LoadModule: "evdev" (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so (II) Module evdev: vendor="X.Org Foundation" compiled for 1.7.6, module version = 2.3.2 Module class: X.Org XInput Driver ABI class: X.Org XInput driver, version 7.0 (**) Power Button: always reports core events (**) Power Button: Device: "/dev/input/event1" (II) Power Button: Found keys (II) Power Button: Configuring as keyboard (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD) (**) Option "xkb_rules" "evdev" (**) Option "xkb_model" "pc105" (**) Option "xkb_layout" "us" (II) config/udev: Adding input device Power Button (/dev/input/event0) (**) Power Button: Applying InputClass "evdev keyboard catchall" (**) Power Button: always reports core events (**) Power Button: Device: "/dev/input/event0" (II) Power Button: Found keys (II) Power Button: Configuring as keyboard (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD) (**) Option "xkb_rules" "evdev" (**) Option "xkb_model" "pc105" (**) Option "xkb_layout" "us" (II) config/udev: Adding input device Logitech USB-PS/2 Optical Mouse (/dev/input/event3) (**) Logitech USB-PS/2 Optical Mouse: Applying InputClass "evdev pointer catchall" (**) Logitech USB-PS/2 Optical Mouse: always reports core events (**) Logitech USB-PS/2 Optical Mouse: Device: "/dev/input/event3" (II) Logitech USB-PS/2 Optical Mouse: Found 12 mouse buttons (II) Logitech USB-PS/2 Optical Mouse: Found scroll wheel(s) (II) Logitech USB-PS/2 Optical Mouse: Found relative axes (II) Logitech USB-PS/2 Optical Mouse: Found x and y relative axes (II) Logitech USB-PS/2 Optical Mouse: Configuring as mouse (**) Logitech USB-PS/2 Optical Mouse: YAxisMapping: buttons 4 and 5 (**) Logitech USB-PS/2 Optical Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200 (II) XINPUT: Adding extended input device "Logitech USB-PS/2 Optical Mouse" (type: MOUSE) (II) Logitech USB-PS/2 Optical Mouse: initialized for relative axes. (II) config/udev: Adding input device Logitech USB-PS/2 Optical Mouse (/dev/input/mouse1) (II) No input driver/identifier specified (ignoring) (II) config/udev: Adding input device Logitech USB Multimedia Keyboard (/dev/input/event4) (**) Logitech USB Multimedia Keyboard: Applying InputClass "evdev keyboard catchall" (**) Logitech USB Multimedia Keyboard: always reports core events (**) Logitech USB Multimedia Keyboard: Device: "/dev/input/event4" (II) Logitech USB Multimedia Keyboard: Found keys (II) Logitech USB Multimedia Keyboard: Configuring as keyboard (II) XINPUT: Adding extended input device "Logitech USB Multimedia Keyboard" (type: KEYBOARD) (**) Option "xkb_rules" "evdev" (**) Option "xkb_model" "pc105" (**) Option "xkb_layout" "us" (II) config/udev: Adding input device Logitech USB Multimedia Keyboard (/dev/input/event5) (**) Logitech USB Multimedia Keyboard: Applying InputClass "evdev keyboard catchall" (**) Logitech USB Multimedia Keyboard: always reports core events (**) Logitech USB Multimedia Keyboard: Device: "/dev/input/event5" (II) Logitech USB Multimedia Keyboard: Found keys (II) Logitech USB Multimedia Keyboard: Configuring as keyboard (II) XINPUT: Adding extended input device "Logitech USB Multimedia Keyboard" (type: KEYBOARD) (**) Option "xkb_rules" "evdev" (**) Option "xkb_model" "pc105" (**) Option "xkb_layout" "us" (II) config/udev: Adding input device KEYBOARD (/dev/input/event6) (**) KEYBOARD: Applying InputClass "evdev keyboard catchall" (**) KEYBOARD: always reports core events (**) KEYBOARD: Device: "/dev/input/event6" (II) KEYBOARD: Found keys (II) KEYBOARD: Configuring as keyboard (II) XINPUT: Adding extended input device "KEYBOARD" (type: KEYBOARD) (**) Option "xkb_rules" "evdev" (**) Option "xkb_model" "pc105" (**) Option "xkb_layout" "us" (II) config/udev: Adding input device KEYBOARD (/dev/input/event7) (**) KEYBOARD: Applying InputClass "evdev keyboard catchall" (**) KEYBOARD: always reports core events (**) KEYBOARD: Device: "/dev/input/event7" (II) KEYBOARD: Found 14 mouse buttons (II) KEYBOARD: Found scroll wheel(s) (II) KEYBOARD: Found relative axes (II) KEYBOARD: Found keys (II) KEYBOARD: Configuring as mouse (II) KEYBOARD: Configuring as keyboard (**) KEYBOARD: YAxisMapping: buttons 4 and 5 (**) KEYBOARD: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200 (II) XINPUT: Adding extended input device "KEYBOARD" (type: KEYBOARD) (**) Option "xkb_rules" "evdev" (**) Option "xkb_model" "pc105" (**) Option "xkb_layout" "us" (EE) KEYBOARD: failed to initialize for relative axes. (II) config/udev: Adding input device KEYBOARD (/dev/input/mouse2) (II) No input driver/identifier specified (ignoring) (II) config/udev: Adding input device Macintosh mouse button emulation (/dev/input/event2) (**) Macintosh mouse button emulation: Applying InputClass "evdev pointer catchall" (**) Macintosh mouse button emulation: always reports core events (**) Macintosh mouse button emulation: Device: "/dev/input/event2" (II) Macintosh mouse button emulation: Found 3 mouse buttons (II) Macintosh mouse button emulation: Found relative axes (II) Macintosh mouse button emulation: Found x and y relative axes (II) Macintosh mouse button emulation: Configuring as mouse (**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5 (**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200 (II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE) (II) Macintosh mouse button emulation: initialized for relative axes. (II) config/udev: Adding input device Macintosh mouse button emulation (/dev/input/mouse0) (II) No input driver/identifier specified (ignoring) (II) fglrx(0): Restoring Recent Mode via PCS is not supported in RANDR 1.2 capable environments

  Read the article

• Increase samba space on open suse 12.1

  - by Kapil Sharma

  I know linux basics but not an expert. IT guy left the job here and there is some time before new hire. So sorry if question is very basic. We have local testing server based on Open SUSE 12.1, which also act as shared drive between dev/mgmt team here and using Samba for that. Now we are running out of space on samba, even though server's 2*1TB harddisk is nearly 90% free. My question is, what is limiting Samba and how can I increase its limit? We need around at least 500 GB as shared drive but currently its just 25 GB. I don't need step by step answer, just a link to any helpful article would be sufficient. Probably I'm putting wrong keywords in google so not getting any helpful link. EDIT: Output of commands in the first comment. All commands were run as root user df -h (getting error with df -ht) Filesystem Size Used Avail Use% Mounted on rootfs 30G 5.1G 23G 19% / devtmpfs 2.0G 36K 2.0G 1% /dev tmpfs 2.0G 1.1M 2.0G 1% /dev/shm tmpfs 2.0G 676K 2.0G 1% /run /dev/sda2 30G 5.1G 23G 19% / tmpfs 2.0G 0 2.0G 0% /sys/fs/cgroup tmpfs 2.0G 676K 2.0G 1% /var/run tmpfs 2.0G 0 2.0G 0% /media tmpfs 2.0G 676K 2.0G 1% /var/lock /dev/sda3 36G 31G 3.3G 91% /home fdisk -l /dev/[hmsv]d* Disk /dev/sda: 80.0 GB, 80026361856 bytes 255 heads, 63 sectors/track, 9729 cylinders, total 156301488 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x2d4a2d49 Device Boot Start End Blocks Id System /dev/sda1 2048 16771071 8384512 82 Linux swap / Solaris /dev/sda2 * 16771072 79681535 31455232 83 Linux /dev/sda3 79681536 156301311 38309888 83 Linux Disk /dev/sda1: 8585 MB, 8585740288 bytes 255 heads, 63 sectors/track, 1043 cylinders, total 16769024 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sda1 doesn't contain a valid partition table Disk /dev/sda2: 32.2 GB, 32210157568 bytes 255 heads, 63 sectors/track, 3915 cylinders, total 62910464 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System Disk /dev/sda3: 39.2 GB, 39229325312 bytes 255 heads, 63 sectors/track, 4769 cylinders, total 76619776 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sda3 doesn't contain a valid partition table vgs No volume groups found lvs No volume groups found output of vi /etc/samba/smb.conf # smb.conf is the main Samba configuration file. You find a full commented # version at /usr/share/doc/packages/samba/examples/smb.conf.SUSE if the # samba-doc package is installed. # Date: 2011-11-02 [global] workgroup = WORKGROUP passdb backend = tdbsam printing = cups printcap name = cups printcap cache time = 750 cups options = raw map to guest = Bad User include = /etc/samba/dhcp.conf logon path = \\%L\profiles\.msprofile logon home = \\%L\%U\.9xprofile logon drive = P: usershare allow guests = Yes [homes] comment = Home Directories valid users = %S, %D%w%S browseable = No read only = No inherit acls = Yes [profiles] comment = Network Profiles Service path = %H read only = No store dos attributes = Yes create mask = 0600 directory mask = 0700 [users] comment = All users path = /home read only = No inherit acls = Yes veto files = /aquota.user/groups/shares/ [groups] comment = All groups path = /home/groups read only = No inherit acls = Yes [printers] comment = All Printers path = /var/tmp printable = Yes create mask = 0600 browseable = No [print$] comment = Printer Drivers path = /var/lib/samba/drivers write list = @ntadmin root force group = ntadmin create mask = 0664 directory mask = 0775 [allusers] comment = All Users path = /home/shares/allusers valid users = @users force group = users create mask = 0660 directory mask = 0771 writable = yes

  Read the article

• Setup access to SAS RAID drives with NTFS partitions on CentOS Machine

  - by Quanano

  We have a Dell Poweredge 2900 system with Adaptec 39320A SCSI CONTROLLER CARD and 4 SAS hard drives attached, with NTFS partitions on them. We installed CentOS on the other raid array with a different controller and it is working fine. We are now trying to access the drives shown above and they are not being shown in /dev as sdb, etc. sda is the drive that we installed centos on and it has sda1, sda2, sda3, etc. The CDROM has been picked up as well. If I scan for scsi devices then the perc and adaptec controllers are both found. sg0 is the CDROM and sg2 is the centos installed, however I think sg1 is the other drive but I cannot see anyway to mount the partitions, as only the drive is listed in /dev. Thanks. EXTRA INFO fdisk -l Disk /dev/sda: 72.7 GB, 72746008576 bytes 255 heads, 63 sectors/track, 8844 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x11e3119f Device Boot Start End Blocks Id System /dev/sda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 64 8845 70528000 8e Linux LVM Disk /dev/mapper/vg_lal2server-lv_root: 34.4 GB, 34431041536 bytes 255 heads, 63 sectors/track, 4186 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_root doesn't contain a valid partition table Disk /dev/mapper/vg_lal2server-lv_swap: 21.1 GB, 21139292160 bytes 255 heads, 63 sectors/track, 2570 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_swap doesn't contain a valid partition table Disk /dev/mapper/vg_lal2server-lv_home: 16.6 GB, 16647192576 bytes 255 heads, 63 sectors/track, 2023 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_home doesn't contain a valid partition table These are all from the install hdd not the additional hard drives modprobe a320raid FATAL: Module a320raid not found. lsscsi -v [0:0:0:0] cd/dvd TSSTcorp CDRWDVD TS-H492C DE02 /dev/sr0 dir: /sys/bus/scsi/devices/0:0:0:0 [/sys/devices/pci0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0:0] [4:0:10:0] enclosu DP BACKPLANE 1.05 - dir: /sys/bus/scsi/devices/4:0:10:0 [/sys/devices/pci0000:00/0000:00:05.0/0000:01:00.0/0000:02:0e.0/host4/target4:0:10/4:0:10:0] [4:2:0:0] disk DELL PERC 5/i 1.03 /dev/sda dir: /sys/bus/scsi/devices/4:2:0:0 [/sys/devices/pci0000:00/0000:00:05.0/0000:01:00.0/0000:02:0e.0/host4/target4:2:0/4:2:0:0] . lsmod Module Size Used by fuse 66285 0 des_generic 16604 0 ecb 2209 0 md4 3461 0 nls_utf8 1455 0 cifs 278370 0 autofs4 26888 4 ipt_REJECT 2383 0 ip6t_REJECT 4628 2 nf_conntrack_ipv6 8748 2 nf_defrag_ipv6 12182 1 nf_conntrack_ipv6 xt_state 1492 2 nf_conntrack 79453 2 nf_conntrack_ipv6,xt_state ip6table_filter 2889 1 ip6_tables 19458 1 ip6table_filter ipv6 322029 31 ip6t_REJECT,nf_conntrack_ipv6,nf_defrag_ipv6 bnx2 79618 0 ses 6859 0 enclosure 8395 1 ses dcdbas 9219 0 serio_raw 4818 0 sg 30124 0 iTCO_wdt 13662 0 iTCO_vendor_support 3088 1 iTCO_wdt i5000_edac 8867 0 edac_core 46773 3 i5000_edac i5k_amb 5105 0 shpchp 33482 0 ext4 364410 3 mbcache 8144 1 ext4 jbd2 88738 1 ext4 sd_mod 39488 3 crc_t10dif 1541 1 sd_mod sr_mod 16228 0 cdrom 39771 1 sr_mod megaraid_sas 77090 2 aic79xx 129492 0 scsi_transport_spi 26151 1 aic79xx pata_acpi 3701 0 ata_generic 3837 0 ata_piix 22846 0 radeon 1023359 1 ttm 70328 1 radeon drm_kms_helper 33236 1 radeon drm 230675 3 radeon,ttm,drm_kms_helper i2c_algo_bit 5762 1 radeon i2c_core 31276 4 radeon,drm_kms_helper,drm,i2c_algo_bit dm_mirror 14101 0 dm_region_hash 12170 1 dm_mirror dm_log 10122 2 dm_mirror,dm_region_hash dm_mod 81500 11 dm_mirror,dm_log

  Read the article

• How do I prevent TCP connection freezes over an OpenVPN network?

  - by Jason R

  New details added at the end of this question; it's possible that I'm zeroing in on the cause. I have a UDP OpenVPN-based VPN set up in tap mode (I need tap because I need the VPN to pass multicast packets, which doesn't seem to be possible with tun networks) with a handful of clients across the Internet. I've been experiencing frequent TCP connection freezes over the VPN. That is, I will establish a TCP connection (e.g. an SSH connection, but other protocols have similar issues), and at some point during the session, it seems that traffic will cease being transmitted over that TCP session. This seems to be related to points at which large data transfers occur, such as if I execute an ls command in an SSH session, or if I cat a long log file. Some Google searches turn up a number of answers like this previous one on Server Fault, indicating that the likely culprit is an MTU issue: that during periods of high traffic, the VPN is trying to send packets that get dropped somewhere in the pipes between the VPN endpoints. The above-linked answer suggests using the following OpenVPN configuration settings to mitigate the problem: fragment 1400 mssfix This should limit the MTU used on the VPN to 1400 bytes and fix the TCP maximum segment size to prevent the generation of any packets larger than that. This seems to mitigate the problem a bit, but I still frequently see the freezes. I've tried a number of sizes as arguments to the fragment directive: 1200, 1000, 576, all with similar results. I can't think of any strange network topology between the two ends that could trigger such a problem: the VPN server is running on a pfSense machine connected directly to the Internet, and my client is also connected directly to the Internet at another location. One other strange piece of the puzzle: if I run the tracepath utility, then that seems to band-aid the problem. A sample run looks like: [~]$ tracepath -n 192.168.100.91 1: 192.168.100.90 0.039ms pmtu 1500 1: 192.168.100.91 40.823ms reached 1: 192.168.100.91 19.846ms reached Resume: pmtu 1500 hops 1 back 64 The above run is between two clients on the VPN: I initiated the trace from 192.168.100.90 to the destination of 192.168.100.91. Both clients were configured with fragment 1200; mssfix; in an attempt to limit the MTU used on the link. The above results would seem to suggest that tracepath was able to detect a path MTU of 1500 bytes between the two clients. I would assume that it would be somewhat smaller due to the fragmentation settings specified in the OpenVPN configuration. I found that result somewhat strange. Even stranger, however: if I have a TCP connection in the stalled state (e.g. an SSH session with a directory listing that froze in the middle), then executing the tracepath command shown above causes the connection to start up again! I can't figure out any reasonable explanation for why this would be the case, but I feel like this might be pointing toward a solution to ultimately eradicate the problem. Does anyone have any recommendations for other things to try? Edit: I've come back and looked at this a bit further, and have found only more confounding information: I set the OpenVPN connection to fragment at 1400 bytes, as shown above. Then, I connected to the VPN from across the Internet and used Wireshark to look at the UDP packets that were sent to the VPN server while the stall occurred. None were greater than the specified 1400 byte count, so the fragmentation seems to be functioning properly. To verify that even a 1400-byte MTU would be sufficient, I pinged the VPN server using the following (Linux) command: ping <host> -s 1450 -M do This (I believe) sends a 1450-byte packet with fragmentation disabled (I at least verified that it didn't work if I set it to an obviously-too-large value like 1600 bytes). These seem to work just fine; I get replies back from the host with no issue. So, maybe this isn't an MTU issue at all. I'm just confused as to what else it might be! Edit 2: The rabbit hole just keeps getting deeper: I've now isolated the problem a bit more. It seems to be related to the exact OS that the VPN client uses. I have successfully duplicated the problem on at least three Ubuntu machines (versions 12.04 through 13.04). I can reliably duplicate an SSH connection freeze within a minute or so by just cat-ing a large log file. However, if I do the same test using a CentOS 6 machine as a client, then I don't see the problem! I've tested using the exact same OpenVPN client version as I was using on the Ubuntu machines. I can cat log files for hours without seeing the connection freeze. This seems to provide some insight as to the ultimate cause, but I'm just not sure what that insight is. I have examined the traffic over the VPN using Wireshark. I'm not a TCP expert, so I'm not sure what to make of the gory details, but the gist is that at some point, a UDP packet gets dropped due to the limited bandwidth of the Internet link, causing TCP retransmissions inside the VPN tunnel. On the CentOS client, these retransmissions occur properly and things move on happily. At some point with the Ubuntu clients, though, the remote end starts retransmitting the same TCP segment over and over (with the transmit delay increasing between each retransmission). The client sends what looks like a valid TCP ACK to each retransmission, but the remote end still continues to transmit the same TCP segment periodically. This extends ad infinitum and the connection stalls. My question here would be: Does anyone have any recommendations for how to troubleshoot and/or determine the root cause of the TCP issue? It's as if the remote end isn't accepting the ACK messages sent by the VPN client. One common difference between the CentOS node and the various Ubuntu releases is that Ubuntu has a much more recent Linux kernel version (from 3.2 in Ubuntu 12.04 to 3.8 in 13.04). A pointer to some new kernel bug maybe? I'm assuming that if that were so, then I wouldn't be the only one experiencing the problem; I don't think this seems like a particularly exotic setup.

  Read the article

• Re: Help with Boost Grammar

  - by Decmac04

  I have redesigned and extended the grammar I asked about earlier as shown below: // BIFAnalyser.cpp : Defines the entry point for the console application. // // /*============================================================================= Copyright (c) Temitope Jos Onunkun 2010 http://www.dcs.kcl.ac.uk/pg/onun/ Use, modification and distribution is subject to the Boost Software License, Version 1.0. (See accompanying file LICENSE_1_0.txt or copy at http://www.boost.org/LICENSE_1_0.txt) =============================================================================*/ //////////////////////////////////////////////////////////////////////////// // // // B Machine parser using the Boost "Grammar" and "Semantic Actions". // // // //////////////////////////////////////////////////////////////////////////// include include include include include include //////////////////////////////////////////////////////////////////////////// using namespace std; using namespace boost::spirit; //////////////////////////////////////////////////////////////////////////// // // Semantic Actions // //////////////////////////////////////////////////////////////////////////// // // namespace { //semantic action function on individual lexeme void do_noint(char const* start, char const* end) { string str(start, end); if (str != "NAT1") cout << "PUSH(" << str << ')' << endl; } //semantic action function on addition of lexemes void do_add(char const*, char const*) { cout << "ADD" << endl; // for(vector::iterator vi = strVect.begin(); vi < strVect.end(); ++vi) // cout << *vi << " "; } //semantic action function on subtraction of lexemes void do_subt(char const*, char const*) { cout << "SUBTRACT" << endl; } //semantic action function on multiplication of lexemes void do_mult(char const*, char const*) { cout << "\nMULTIPLY" << endl; } //semantic action function on division of lexemes void do_div(char const*, char const*) { cout << "\nDIVIDE" << endl; } // // vector flowTable; //semantic action function on simple substitution void do_sSubst(char const* start, char const* end) { string str(start, end); //use boost tokenizer to break down tokens typedef boost::tokenizer Tokenizer; boost::char_separator sep(" -+/*:=()",0,boost::drop_empty_tokens); // char separator definition Tokenizer tok(str, sep); Tokenizer::iterator tok_iter = tok.begin(); pair dependency; //create a pair object for dependencies //create a vector object to store all tokens vector dx; // int counter = 0; // tracks token position for(tok.begin(); tok_iter != tok.end(); ++tok_iter) //save all tokens in vector { dx.push_back(*tok_iter ); } counter = dx.size(); // vector d_hat; //stores set of dependency pairs string dep; //pairs variables as string object // dependency.first = *tok.begin(); vector FV; for(int unsigned i=1; i < dx.size(); i++) { // if(!atoi(dx.at(i).c_str()) && (dx.at(i) !=" ")) { dependency.second = dx.at(i); dep = dependency.first + "|-" + dependency.second + " "; d_hat.push_back(dep); vector<string> row; row.push_back(dependency.first); //push x_hat into first column of each row for(unsigned int j=0; j<2; j++) { row.push_back(dependency.second);//push an element (column) into the row } flowTable.push_back(row); //Add the row to the main vector } } //displays internal representation of information flow table cout << "\n****************\nDependency Table\n****************\n"; cout << "X_Hat\tDx\tG_Hat\n"; cout << "-----------------------------\n"; for(unsigned int i=0; i < flowTable.size(); i++) { for(unsigned int j=0; j<2; j++) { cout << flowTable[i][j] << "\t "; } if (*tok.begin() != "WHILE" ) //if there are no global flows, cout << "\t{}"; //display empty set cout << "\n"; } cout << "***************\n\n"; for(int unsigned j=0; j < FV.size(); j++) { if(FV.at(j) != dependency.second) dep = dependency.first + "|-" + dependency.second + " "; d_hat.push_back(dep); } cout << "PUSH(" << str << ')' << endl; cout << "\n*******\nDependency pairs\n*******\n"; for(int unsigned i=0; i < d_hat.size(); i++) cout << d_hat.at(i) << "\n...\n"; cout << "\nSIMPLE SUBSTITUTION\n\n"; } //semantic action function on multiple substitution void do_mSubst(char const* start, char const* end) { string str(start, end); cout << "PUSH(" << str << ')' << endl; //cout << "\nMULTIPLE SUBSTITUTION\n\n"; } //semantic action function on unbounded choice substitution void do_mChoice(char const* start, char const* end) { string str(start, end); cout << "PUSH(" << str << ')' << endl; cout << "\nUNBOUNDED CHOICE SUBSTITUTION\n\n"; } void do_logicExpr(char const* start, char const* end) { string str(start, end); //use boost tokenizer to break down tokens typedef boost::tokenizer Tokenizer; boost::char_separator sep(" -+/*=:()<",0,boost::drop_empty_tokens); // char separator definition Tokenizer tok(str, sep); Tokenizer::iterator tok_iter = tok.begin(); //pair dependency; //create a pair object for dependencies //create a vector object to store all tokens vector dx; for(tok.begin(); tok_iter != tok.end(); ++tok_iter) //save all tokens in vector { dx.push_back(*tok_iter ); } for(unsigned int i=0; i cout << "PUSH(" << str << ')' << endl; cout << "\nPREDICATE\n\n"; } void do_predicate(char const* start, char const* end) { string str(start, end); cout << "PUSH(" << str << ')' << endl; cout << "\nMULTIPLE PREDICATE\n\n"; } void do_ifSelectPre(char const* start, char const* end) { string str(start, end); //if cout << "PUSH(" << str << ')' << endl; cout << "\nPROTECTED SUBSTITUTION\n\n"; } //semantic action function on machine substitution void do_machSubst(char const* start, char const* end) { string str(start, end); cout << "PUSH(" << str << ')' << endl; cout << "\nMACHINE SUBSTITUTION\n\n"; } } //////////////////////////////////////////////////////////////////////////// // // Machine Substitution Grammar // //////////////////////////////////////////////////////////////////////////// // Simple substitution grammar parser with integer values removed struct Substitution : public grammar { template struct definition { definition(Substitution const& ) { machine_subst = ( (simple_subst) | (multi_subst) | (if_select_pre_subst) | (unbounded_choice) )[&do_machSubst] ; unbounded_choice = str_p("ANY") ide_list str_p("WHERE") predicate str_p("THEN") machine_subst str_p("END") ; if_select_pre_subst = ( ( str_p("IF") predicate str_p("THEN") machine_subst *( str_p("ELSIF") predicate machine_subst ) !( str_p("ELSE") machine_subst) str_p("END") ) | ( str_p("SELECT") predicate str_p("THEN") machine_subst *( str_p("WHEN") predicate machine_subst ) !( str_p("ELSE") machine_subst) str_p("END")) | ( str_p("PRE") predicate str_p("THEN") machine_subst str_p("END") ) )[&do_ifSelectPre] ; multi_subst = ( (machine_subst) *( ( str_p("||") (machine_subst) ) | ( str_p("[]") (machine_subst) ) ) ) [&do_mSubst] ; simple_subst = (identifier str_p(":=") arith_expr) [&do_sSubst] ; expression = predicate | arith_expr ; predicate = ( (logic_expr) *( ( ch_p('&') (logic_expr) ) | ( str_p("OR") (logic_expr) ) ) )[&do_predicate] ; logic_expr = ( identifier (str_p("<") arith_expr) | (str_p("<") arith_expr) | (str_p("/:") arith_expr) | (str_p("<:") arith_expr) | (str_p("/<:") arith_expr) | (str_p("<<:") arith_expr) | (str_p("/<<:") arith_expr) | (str_p("<=") arith_expr) | (str_p("=") arith_expr) | (str_p("=") arith_expr) | (str_p("=") arith_expr) ) [&do_logicExpr] ; arith_expr = term *( ('+' term)[&do_add] | ('-' term)[&do_subt] ) ; term = factor ( ('' factor)[&do_mult] | ('/' factor)[&do_div] ) ; factor = lexeme_d[( identifier | +digit_p)[&do_noint]] | '(' expression ')' | ('+' factor) ; ide_list = identifier *( ch_p(',') identifier ) ; identifier = alpha_p +( alnum_p | ch_p('_') ) ; } rule machine_subst, unbounded_choice, if_select_pre_subst, multi_subst, simple_subst, expression, predicate, logic_expr, arith_expr, term, factor, ide_list, identifier; rule<ScannerT> const& start() const { return predicate; //return multi_subst; //return machine_subst; } }; }; //////////////////////////////////////////////////////////////////////////// // // Main program // //////////////////////////////////////////////////////////////////////////// int main() { cout << "*********************************\n\n"; cout << "\t\t...Machine Parser...\n\n"; cout << "*********************************\n\n"; // cout << "Type an expression...or [q or Q] to quit\n\n"; string str; int machineCount = 0; char strFilename[256]; //file name store as a string object do { cout << "Please enter a filename...or [q or Q] to quit:\n\n "; //prompt for file name to be input //char strFilename[256]; //file name store as a string object cin strFilename; if(*strFilename == 'q' || *strFilename == 'Q') //termination condition return 0; ifstream inFile(strFilename); // opens file object for reading //output file for truncated machine (operations only) if (inFile.fail()) cerr << "\nUnable to open file for reading.\n" << endl; inFile.unsetf(std::ios::skipws); Substitution elementary_subst; // Simple substitution parser object string next; while (inFile str) { getline(inFile, next); str += next; if (str.empty() || str[0] == 'q' || str[0] == 'Q') break; parse_info< info = parse(str.c_str(), elementary_subst !end_p, space_p); if (info.full) { cout << "\n-------------------------\n"; cout << "Parsing succeeded\n"; cout << "\n-------------------------\n"; } else { cout << "\n-------------------------\n"; cout << "Parsing failed\n"; cout << "stopped at: " << info.stop << "\"\n"; cout << "\n-------------------------\n"; } } } while ( (*strFilename != 'q' || *strFilename !='Q')); return 0; } However, I am experiencing the following unexpected behaviours on testing: The text files I used are: f1.txt, ... containing ...: debt:=(LoanRequest+outstandingLoan1)*20 . f2.txt, ... containing ...: debt:=(LoanRequest+outstandingLoan1)*20 || newDebt := loanammount-paidammount || price := purchasePrice + overhead + bb . f3.txt, ... containing ...: yy < (xx+7+ww) . f4.txt, ... containing ...: yy < (xx+7+ww) & yy : NAT . When I use multi_subst as start rule both files (f1 and f2) are parsed correctly; When I use machine_subst as start rule file f1 parse correctly, while file f2 fails, producing the error: “Parsing failed stopped at: || newDebt := loanammount-paidammount || price := purchasePrice + overhead + bb” When I use predicate as start symbol, file f3 parse correctly, but file f4 yields the error: “ “Parsing failed stopped at: & yy : NAT” Can anyone help with the grammar, please? It appears there are problems with the grammar that I have so far been unable to spot.

  Read the article

• ASP.NET MVC 3: Implicit and Explicit code nuggets with Razor

  - by ScottGu

  This is another in a series of posts I’m doing that cover some of the new ASP.NET MVC 3 features: New @model keyword in Razor (Oct 19th) Layouts with Razor (Oct 22nd) Server-Side Comments with Razor (Nov 12th) Razor’s @: and <text> syntax (Dec 15th) Implicit and Explicit code nuggets with Razor (today) In today’s post I’m going to discuss how Razor enables you to both implicitly and explicitly define code nuggets within your view templates, and walkthrough some code examples of each of them.  Fluid Coding with Razor ASP.NET MVC 3 ships with a new view-engine option called “Razor” (in addition to the existing .aspx view engine).  You can learn more about Razor, why we are introducing it, and the syntax it supports from my Introducing Razor blog post. Razor minimizes the number of characters and keystrokes required when writing a view template, and enables a fast, fluid coding workflow. Unlike most template syntaxes, you do not need to interrupt your coding to explicitly denote the start and end of server blocks within your HTML. The Razor parser is smart enough to infer this from your code. This enables a compact and expressive syntax which is clean, fast and fun to type. For example, the Razor snippet below can be used to iterate a collection of products and output a <ul> list of product names that link to their corresponding product pages: When run, the above code generates output like below: Notice above how we were able to embed two code nuggets within the content of the foreach loop.  One of them outputs the name of the Product, and the other embeds the ProductID within a hyperlink.  Notice that we didn’t have to explicitly wrap these code-nuggets - Razor was instead smart enough to implicitly identify where the code began and ended in both of these situations.  How Razor Enables Implicit Code Nuggets Razor does not define its own language.  Instead, the code you write within Razor code nuggets is standard C# or VB.  This allows you to re-use your existing language skills, and avoid having to learn a customized language grammar. The Razor parser has smarts built into it so that whenever possible you do not need to explicitly mark the end of C#/VB code nuggets you write.  This makes coding more fluid and productive, and enables a nice, clean, concise template syntax.  Below are a few scenarios that Razor supports where you can avoid having to explicitly mark the beginning/end of a code nugget, and instead have Razor implicitly identify the code nugget scope for you: Property Access Razor allows you to output a variable value, or a sub-property on a variable that is referenced via “dot” notation: You can also use “dot” notation to access sub-properties multiple levels deep: Array/Collection Indexing: Razor allows you to index into collections or arrays: Calling Methods: Razor also allows you to invoke methods: Notice how for all of the scenarios above how we did not have to explicitly end the code nugget.  Razor was able to implicitly identify the end of the code block for us. Razor’s Parsing Algorithm for Code Nuggets The below algorithm captures the core parsing logic we use to support “@” expressions within Razor, and to enable the implicit code nugget scenarios above: Parse an identifier - As soon as we see a character that isn't valid in a C# or VB identifier, we stop and move to step 2 Check for brackets - If we see "(" or "[", go to step 2.1., otherwise, go to step 3  Parse until the matching ")" or "]" (we track nested "()" and "[]" pairs and ignore "()[]" we see in strings or comments) Go back to step 2 Check for a "." - If we see one, go to step 3.1, otherwise, DO NOT ACCEPT THE "." as code, and go to step 4 If the character AFTER the "." is a valid identifier, accept the "." and go back to step 1, otherwise, go to step 4 Done! Differentiating between code and content Step 3.1 is a particularly interesting part of the above algorithm, and enables Razor to differentiate between scenarios where an identifier is being used as part of the code statement, and when it should instead be treated as static content: Notice how in the snippet above we have ? and ! characters at the end of our code nuggets.  These are both legal C# identifiers – but Razor is able to implicitly identify that they should be treated as static string content as opposed to being part of the code expression because there is whitespace after them.  This is pretty cool and saves us keystrokes. Explicit Code Nuggets in Razor Razor is smart enough to implicitly identify a lot of code nugget scenarios.  But there are still times when you want/need to be more explicit in how you scope the code nugget expression.  The @(expression) syntax allows you to do this: You can write any C#/VB code statement you want within the @() syntax.  Razor will treat the wrapping () characters as the explicit scope of the code nugget statement.  Below are a few scenarios where we could use the explicit code nugget feature: Perform Arithmetic Calculation/Modification: You can perform arithmetic calculations within an explicit code nugget: Appending Text to a Code Expression Result: You can use the explicit expression syntax to append static text at the end of a code nugget without having to worry about it being incorrectly parsed as code: Above we have embedded a code nugget within an <img> element’s src attribute.  It allows us to link to images with URLs like “/Images/Beverages.jpg”.  Without the explicit parenthesis, Razor would have looked for a “.jpg” property on the CategoryName (and raised an error).  By being explicit we can clearly denote where the code ends and the text begins. Using Generics and Lambdas Explicit expressions also allow us to use generic types and generic methods within code expressions – and enable us to avoid the <> characters in generics from being ambiguous with tag elements. One More Thing….Intellisense within Attributes We have used code nuggets within HTML attributes in several of the examples above.  One nice feature supported by the Razor code editor within Visual Studio is the ability to still get VB/C# intellisense when doing this. Below is an example of C# code intellisense when using an implicit code nugget within an <a> href=”” attribute: Below is an example of C# code intellisense when using an explicit code nugget embedded in the middle of a <img> src=”” attribute: Notice how we are getting full code intellisense for both scenarios – despite the fact that the code expression is embedded within an HTML attribute (something the existing .aspx code editor doesn’t support).  This makes writing code even easier, and ensures that you can take advantage of intellisense everywhere. Summary Razor enables a clean and concise templating syntax that enables a very fluid coding workflow.  Razor’s ability to implicitly scope code nuggets reduces the amount of typing you need to perform, and leaves you with really clean code. When necessary, you can also explicitly scope code expressions using a @(expression) syntax to provide greater clarity around your intent, as well as to disambiguate code statements from static markup. Hope this helps, Scott P.S. In addition to blogging, I am also now using Twitter for quick updates and to share links. Follow me at: twitter.com/scottgu

  Read the article

• OpenGL Colorspace Conversion

  - by Steven Behnke

  Does anyone know how to create a texture with a YUV colorspace so that we can get hardware based YUV to RGB colorspace conversion without having to use a fragment shader? I'm using an NVidia 9400 and I don't see an obvious GL extension that seems to do the trick. I've found examples how to use a fragment shader, but the project I'm working on currently only supports OpenGL 1.1 and I don't have time to convert it to 2.0 and perform all the regression testing necessary. This is also targeting Linux. On other platforms I've been using a MESA extension but it doesn't function on the Nvidia card.

  Read the article

• Caching query results in django

  - by Marcio Cruz

  I'm trying to find a way to cache the results of a query that won't change with frequency. For example, categories of products from an e-commerce (cellphones, TV, etc). I'm thinking of using the template fragment caching, but in this fragment, I will iterate over a list of these categories. This list is avaliable in any part of the site, so it's in my base.html file. Do I have always to send the list of categories when rendering the templates? Or is there a more dynamic way to do this, making the list always available in the template?

  Read the article

< Previous Page | 20 21 22 23 24 25 26 27 28 29 30 31  | Next Page >