Search Results

Search found 2072 results on 83 pages for 'nvidia ion'.

Page 24/83 | < Previous Page | 20 21 22 23 24 25 26 27 28 29 30 31  | Next Page >

• optirun fails in Ubuntu 12.10

  - by chiloxsan

  I am trying to use Nvidia Optimus on my laptop by using Bumblebee, I have an Intel Core i5 with an Nvidia Geforce GT 630M. I have followed the instructions on the wiki page at https://wiki.ubuntu.com/Bumblebee, but when trying to run optirun with Firefox (or any other program, like glxspheres), I get the following error: [ 1921.452820] [ERROR]Cannot access secondary GPU - error: Could not load GPU driver [ 1921.452905] [ERROR]Aborting because fallback start is disabled. I have tried googling the issue but I couldn't find any solution that didn't cause more problems. Thank you for your time. Here is my bumblebee.conf: http://paste.ubuntu.com/1333324/

  Read the article

• Dual display setup - only one displayed after logon

  - by oneofthemany

  During boot process my desktop shows both Monitors, but after log I only get one. I'm using Ubuntu 11.10 When I go into Displays its still only shows on Monitor. Here is my graphics card details: 01:00.0 VGA compatible controller: nVidia Corporation G72 [GeForce 7300 LE] (rev a1) (prog-if 00 [VGA controller]) Subsystem: Dell Device 0405 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at dd000000 (32-bit, non-prefetchable) [size=16M] Memory at c0000000 (64-bit, prefetchable) [size=256M] Memory at de000000 (64-bit, non-prefetchable) [size=16M] [virtual] Expansion ROM at dfe00000 [disabled] [size=128K] Capabilities: <access denied> Kernel driver in use: nvidia Kernel modules: nvidia_96, nvidia_173, nouveau, nvidiafb

  Read the article

• 12.04 + Alienware M11x R2 + Bumblebee 3.0 = low resolution only

  - by user89171

  I had a fresh install of Ubuntu 12.04 on my Alienware M11x, and it worked with the native monitor resolution of 1366x768. In trying to get the Optimus chipset working, I installed Bumblebee 3.0. Now, I am only offered 640x480 for my monitor resolution. Graphically, Unity 3D appears to be working now, instead of the Unity 2D I had before, so something went right, but I don't know how I can get it to offer me any higher resolutions than 640x480. I've looked up many pages that address this topic, but nothing that I've seen suggested has worked. sudo add-apt-repository ppa:bumblebee/stable sudo apt-get update sudo apt-get install bumblebee-nvidia was the latest thing I tried. I've tried some variants of this, I've been sure to uninstall nvidia drivers prior to reinstalling Bumblebee and various video drivers. Does anyone have any clue as to how I can get back to native resolution?

  Read the article

• Bumblebee screwd up my grafics-settings

  - by user104762

  I had my system working pretty good with the external monitor working with the displayport. Unfortunately I felt that I should try to install Bumblebee. It didn't work. The monitor wasn't recognised. So I uninstalled it with the instructions on ubuntus wiki. But it didn't get back to the way it was. And when I copied the Purge-command it started deleting other stuff to, like Cheese and whatnot. I can't get the external monitor to be recognised. If I activate Optimus I get the right settings on my laptopscreen, but no Nvidia-drivers. If I deactivate optimus I get poor resolution on my laptopscreen, and still don't recognise the external monitor. But the Nvidia-drivers show up and can be activated. Why oh why did I have to try to install Bumblebee.

  Read the article

• Run 3 monitors on two different video cards?

  - by hullot

  Can I run 3 monitors on two different video cards? I have an ATI and Nvidia brand card. The ATI has 2 HDMI connections. They both work. Both cards are also picked up in Windows, one being the ATI and the other one as the Nvidia, but it says VGA Controller, although the card only takes 2 DVi. So, one DVI cable goes into that Nvidia card. 3 Monitors, but only 2 the HDMI ones from the ATI pick up, not the third one which is connected to the Nvidia via DVI. How can I run three monitors then? I suppose I can't install both drivers, so I'm unsure what to do. Is this possible? I just want the Nvidia card to power the third screen, no gaming on it, nothing. Also the ATI is picked up as primary card as well, so no hurdle there. EDIT: Hm, just installed the Nvidia drivers and it picked up the third screen no problem. Hope there aren't any major conflicts. Will post this as an answer as correct when I'm able. Can't as a new user.

  Read the article

• WPA2 authentication fails on Ubuntu 12.04 using Rosewill RNX-N1

  - by user94156

  Decided to reduce the clutter in the house and replace a wired connection with a wireless one on my wife's system using USB network device Rosewill RNX-X1. I can see and connect to unprotected network, but WPA2 authentication repeatedly fails. RNX-X1 works on other systems (including TV); also have 2 of 'em and tried each. Worth noting that I recently switched from Comcast to CenturyLink and so switched routers. The system connected successfully to previous router (Linksys EA4500) using WPA2. Would think it is the router (Actiontec C1000A) but all other devices (TV, iPad, Windows, Blackberry, and Squeezebox) connect ok. Would appreciate some diagnostic guidance and insight (phrased for a newbie!) Tests to date: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 01 serial: 00:e0:4d:30:40:a1 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:47 ioport:ac00(size=256) memory:fdcff000-fdcfffff memory:fdb00000-fdb1ffff *-network description: Wireless interface physical id: 1 bus info: usb@1:2 logical name: wlan1 serial: 00:02:6f:bd:30:a0 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2800usb driverversion=3.2.0-31-generic firmware=0.29 link=no multicast=yes wireless=IEEE 802.11bgn sudo lspci -v 00:00.0 RAM memory: NVIDIA Corporation MCP67 Memory Controller (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 Capabilities: [44] HyperTransport: Slave or Primary Interface Capabilities: [dc] HyperTransport: MSI Mapping Enable+ Fixed- 00:01.0 ISA bridge: NVIDIA Corporation MCP67 ISA Bridge (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 00:01.1 SMBus: NVIDIA Corporation MCP67 SMBus (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: 66MHz, fast devsel, IRQ 11 I/O ports at fc00 [size=64] I/O ports at 1c00 [size=64] I/O ports at 1c40 [size=64] Capabilities: [44] Power Management version 2 Kernel driver in use: nForce2_smbus Kernel modules: i2c-nforce2 00:01.2 RAM memory: NVIDIA Corporation MCP67 Memory Controller (rev a2) Flags: 66MHz, fast devsel 00:02.0 USB controller: NVIDIA Corporation MCP67 OHCI USB 1.1 Controller (rev a2) (prog-if 10 [OHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23 Memory at fe02f000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Kernel driver in use: ohci_hcd 00:02.1 USB controller: NVIDIA Corporation MCP67 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22 Memory at fe02e000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Kernel driver in use: ehci_hcd 00:04.0 USB controller: NVIDIA Corporation MCP67 OHCI USB 1.1 Controller (rev a2) (prog-if 10 [OHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21 Memory at fe02d000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Kernel driver in use: ohci_hcd 00:04.1 USB controller: NVIDIA Corporation MCP67 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 20 Memory at fe02c000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Kernel driver in use: ehci_hcd 00:06.0 IDE interface: NVIDIA Corporation MCP67 IDE Controller (rev a1) (prog-if 8a [Master SecP PriP]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1] I/O ports at f000 [size=16] Capabilities: [44] Power Management version 2 Kernel driver in use: pata_amd Kernel modules: pata_amd 00:07.0 Audio device: NVIDIA Corporation MCP67 High Definition Audio (rev a1) Subsystem: Biostar Microtech Int'l Corp Device 820c Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22 Memory at fe024000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+ Capabilities: [6c] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:08.0 PCI bridge: NVIDIA Corporation MCP67 PCI Bridge (rev a2) (prog-if 01 [Subtractive decode]) Flags: bus master, 66MHz, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: fdf00000-fdffffff Prefetchable memory behind bridge: fd000000-fd0fffff Capabilities: [b8] Subsystem: NVIDIA Corporation Device cb84 Capabilities: [8c] HyperTransport: MSI Mapping Enable- Fixed- 00:09.0 IDE interface: NVIDIA Corporation MCP67 AHCI Controller (rev a2) (prog-if 85 [Master SecO PriO]) Subsystem: Biostar Microtech Int'l Corp Device 5407 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23 I/O ports at 09f0 [size=8] I/O ports at 0bf0 [size=4] I/O ports at 0970 [size=8] I/O ports at 0b70 [size=4] I/O ports at dc00 [size=16] Memory at fe02a000 (32-bit, non-prefetchable) [size=8K] Capabilities: [44] Power Management version 2 Capabilities: [8c] SATA HBA v1.0 Capabilities: [b0] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: ahci 00:0b.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000b000-0000bfff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000fdd00000-00000000fddfffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0c.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 0000a000-0000afff Memory behind bridge: fdc00000-fdcfffff Prefetchable memory behind bridge: 00000000fdb00000-00000000fdbfffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0d.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 00009000-00009fff Memory behind bridge: fda00000-fdafffff Prefetchable memory behind bridge: 00000000fd900000-00000000fd9fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0e.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 I/O behind bridge: 00008000-00008fff Memory behind bridge: fd800000-fd8fffff Prefetchable memory behind bridge: 00000000fd700000-00000000fd7fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0f.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=06, subordinate=06, sec-latency=0 I/O behind bridge: 00007000-00007fff Memory behind bridge: fd600000-fd6fffff Prefetchable memory behind bridge: 00000000fd500000-00000000fd5fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:10.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=07, subordinate=07, sec-latency=0 I/O behind bridge: 00006000-00006fff Memory behind bridge: fd400000-fd4fffff Prefetchable memory behind bridge: 00000000fd300000-00000000fd3fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:11.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=08, subordinate=08, sec-latency=0 I/O behind bridge: 00005000-00005fff Memory behind bridge: fd200000-fd2fffff Prefetchable memory behind bridge: 00000000fd100000-00000000fd1fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:12.0 VGA compatible controller: NVIDIA Corporation C68 [GeForce 7050 PV / nForce 630a] (rev a2) (prog-if 00 [VGA controller]) Subsystem: Biostar Microtech Int'l Corp Device 1406 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21 Memory at fb000000 (32-bit, non-prefetchable) [size=16M] Memory at e0000000 (64-bit, prefetchable) [size=256M] Memory at fc000000 (64-bit, non-prefetchable) [size=16M] [virtual] Expansion ROM at 80000000 [disabled] [size=128K] Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Kernel driver in use: nvidia Kernel modules: nvidia_current, nouveau, nvidiafb 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration Flags: fast devsel Capabilities: [80] HyperTransport: Host or Secondary Interface 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map Flags: fast devsel 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller Flags: fast devsel 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control Flags: fast devsel Capabilities: [f0] Secure device <?> Kernel driver in use: k8temp Kernel modules: k8temp 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) Subsystem: Biostar Microtech Int'l Corp Device 2305 Flags: bus master, fast devsel, latency 0, IRQ 47 I/O ports at ac00 [size=256] Memory at fdcff000 (64-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at fdb00000 [disabled] [size=128K] Capabilities: [40] Power Management version 2 Capabilities: [48] Vital Product Data Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] Express Endpoint, MSI 00 Capabilities: [84] Vendor Specific Information: Len=4c <?> Capabilities: [100] Advanced Error Reporting Capabilities: [12c] Virtual Channel Capabilities: [148] Device Serial Number 32-00-00-00-10-ec-81-68 Capabilities: [154] Power Budgeting <?> Kernel driver in use: r8169 Kernel modules: r8169 sudo rfkill list all 2: phy2: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• WPA2 authentication fails using USB network devices (Linksys and Rosewill)

  - by Greg Youtz

  Decided to reduce the clutter in the house and replace a wired connection with a wireless one on my wife's system using USB network device Rosewill RNX-X1. I can see and connect to unprotected network, but WPA2 authentication repeatedly fails. Tried the same with a Linksys USB network adapter. Both failed to authenticate. Worth noting that I recently switched from Comcast to CenturyLink and so switched routers. The system connected successfully to previous router (Linksys EA4500) using WPA2. Would think it is the router (Actiontec C1000A) but all other devices (TV, iPad, Windows, Blackberry, and Squeezebox) connect ok. Would appreciate some diagnostic guidance and insight (phrased for a newbie!) Tests to date: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 01 serial: 00:e0:4d:30:40:a1 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:47 ioport:ac00(size=256) memory:fdcff000-fdcfffff memory:fdb00000-fdb1ffff *-network description: Wireless interface physical id: 1 bus info: usb@1:2 logical name: wlan1 serial: 00:02:6f:bd:30:a0 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2800usb driverversion=3.2.0-31-generic firmware=0.29 link=no multicast=yes wireless=IEEE 802.11bgn sudo lspci -v 00:00.0 RAM memory: NVIDIA Corporation MCP67 Memory Controller (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 Capabilities: [44] HyperTransport: Slave or Primary Interface Capabilities: [dc] HyperTransport: MSI Mapping Enable+ Fixed- 00:01.0 ISA bridge: NVIDIA Corporation MCP67 ISA Bridge (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 00:01.1 SMBus: NVIDIA Corporation MCP67 SMBus (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: 66MHz, fast devsel, IRQ 11 I/O ports at fc00 [size=64] I/O ports at 1c00 [size=64] I/O ports at 1c40 [size=64] Capabilities: [44] Power Management version 2 Kernel driver in use: nForce2_smbus Kernel modules: i2c-nforce2 00:01.2 RAM memory: NVIDIA Corporation MCP67 Memory Controller (rev a2) Flags: 66MHz, fast devsel 00:02.0 USB controller: NVIDIA Corporation MCP67 OHCI USB 1.1 Controller (rev a2) (prog-if 10 [OHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23 Memory at fe02f000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Kernel driver in use: ohci_hcd 00:02.1 USB controller: NVIDIA Corporation MCP67 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22 Memory at fe02e000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Kernel driver in use: ehci_hcd 00:04.0 USB controller: NVIDIA Corporation MCP67 OHCI USB 1.1 Controller (rev a2) (prog-if 10 [OHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21 Memory at fe02d000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Kernel driver in use: ohci_hcd 00:04.1 USB controller: NVIDIA Corporation MCP67 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 20 Memory at fe02c000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Kernel driver in use: ehci_hcd 00:06.0 IDE interface: NVIDIA Corporation MCP67 IDE Controller (rev a1) (prog-if 8a [Master SecP PriP]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1] I/O ports at f000 [size=16] Capabilities: [44] Power Management version 2 Kernel driver in use: pata_amd Kernel modules: pata_amd 00:07.0 Audio device: NVIDIA Corporation MCP67 High Definition Audio (rev a1) Subsystem: Biostar Microtech Int'l Corp Device 820c Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22 Memory at fe024000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+ Capabilities: [6c] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:08.0 PCI bridge: NVIDIA Corporation MCP67 PCI Bridge (rev a2) (prog-if 01 [Subtractive decode]) Flags: bus master, 66MHz, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: fdf00000-fdffffff Prefetchable memory behind bridge: fd000000-fd0fffff Capabilities: [b8] Subsystem: NVIDIA Corporation Device cb84 Capabilities: [8c] HyperTransport: MSI Mapping Enable- Fixed- 00:09.0 IDE interface: NVIDIA Corporation MCP67 AHCI Controller (rev a2) (prog-if 85 [Master SecO PriO]) Subsystem: Biostar Microtech Int'l Corp Device 5407 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23 I/O ports at 09f0 [size=8] I/O ports at 0bf0 [size=4] I/O ports at 0970 [size=8] I/O ports at 0b70 [size=4] I/O ports at dc00 [size=16] Memory at fe02a000 (32-bit, non-prefetchable) [size=8K] Capabilities: [44] Power Management version 2 Capabilities: [8c] SATA HBA v1.0 Capabilities: [b0] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: ahci 00:0b.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000b000-0000bfff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000fdd00000-00000000fddfffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0c.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 0000a000-0000afff Memory behind bridge: fdc00000-fdcfffff Prefetchable memory behind bridge: 00000000fdb00000-00000000fdbfffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0d.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 00009000-00009fff Memory behind bridge: fda00000-fdafffff Prefetchable memory behind bridge: 00000000fd900000-00000000fd9fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0e.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 I/O behind bridge: 00008000-00008fff Memory behind bridge: fd800000-fd8fffff Prefetchable memory behind bridge: 00000000fd700000-00000000fd7fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0f.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=06, subordinate=06, sec-latency=0 I/O behind bridge: 00007000-00007fff Memory behind bridge: fd600000-fd6fffff Prefetchable memory behind bridge: 00000000fd500000-00000000fd5fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:10.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=07, subordinate=07, sec-latency=0 I/O behind bridge: 00006000-00006fff Memory behind bridge: fd400000-fd4fffff Prefetchable memory behind bridge: 00000000fd300000-00000000fd3fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:11.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=08, subordinate=08, sec-latency=0 I/O behind bridge: 00005000-00005fff Memory behind bridge: fd200000-fd2fffff Prefetchable memory behind bridge: 00000000fd100000-00000000fd1fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:12.0 VGA compatible controller: NVIDIA Corporation C68 [GeForce 7050 PV / nForce 630a] (rev a2) (prog-if 00 [VGA controller]) Subsystem: Biostar Microtech Int'l Corp Device 1406 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21 Memory at fb000000 (32-bit, non-prefetchable) [size=16M] Memory at e0000000 (64-bit, prefetchable) [size=256M] Memory at fc000000 (64-bit, non-prefetchable) [size=16M] [virtual] Expansion ROM at 80000000 [disabled] [size=128K] Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Kernel driver in use: nvidia Kernel modules: nvidia_current, nouveau, nvidiafb 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration Flags: fast devsel Capabilities: [80] HyperTransport: Host or Secondary Interface 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map Flags: fast devsel 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller Flags: fast devsel 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control Flags: fast devsel Capabilities: [f0] Secure device <?> Kernel driver in use: k8temp Kernel modules: k8temp 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) Subsystem: Biostar Microtech Int'l Corp Device 2305 Flags: bus master, fast devsel, latency 0, IRQ 47 I/O ports at ac00 [size=256] Memory at fdcff000 (64-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at fdb00000 [disabled] [size=128K] Capabilities: [40] Power Management version 2 Capabilities: [48] Vital Product Data Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] Express Endpoint, MSI 00 Capabilities: [84] Vendor Specific Information: Len=4c <?> Capabilities: [100] Advanced Error Reporting Capabilities: [12c] Virtual Channel Capabilities: [148] Device Serial Number 32-00-00-00-10-ec-81-68 Capabilities: [154] Power Budgeting <?> Kernel driver in use: r8169 Kernel modules: r8169 sudo rfkill list all 2: phy2: Wireless LAN Soft blocked: no Hard blocked: no Would appreciate insight on how to chase this down.

  Read the article

• Dell M4600 with nVidia Quadro 2000M hangs on boot when external monitor is connected

  - by vladeta

  I have a problem with my fresh installed Ubuntu 12.04 LTS on my Dell M4600: nVidia quadro 2000M i7-2860 16GB ram 128GB SSD Dell/Samsung 750GB HDD IPS RGB laptop display When it is connected via DP++ to the external Dell U2311H monitor, it hangs on boot or when wakening from suspend. If I detach the DP cable it boots normally. I have tried all combinations that I have found, as adding to grub: "no splash", "boot=pci", "acpi=off", etc... I have also changed in nVidia X settings that external monitor is the primary one and also tried to delete monitor.xml file. There is no change it hangs each time after grub. It starts to load daemons then both screens are blank and then completely hangs with beep sound. What I discovered is if I detach the cable and wait for about 2 sec after grub starts booting and then physically connect DP cable while the Ubuntu is still booting everything works normally and I have a picture on my external screen while the laptop screen is off, just as I wanted. Do you maybe know how to solve this issue? Thank You.

  Read the article

• Cannot establish maximum resolution on ASUS PB278Q

  - by dentuzhik

  I've recently bought brand new ASUS PB278Q monitor. When trying to connect to my laptop, everything works great, except that I can't get the native resolution of my monitor (2560x1440) working. The automatic is 1920x1080. My graphic card is Nvidia GeForce 320m. Here's output from lspci for it: ~$ lspci | grep VGA 02:00.0 VGA compatible controller: NVIDIA Corporation GT216M [GeForce GT 320M] (rev a2) and also xrandr: ~$ xrandr Screen 0: minimum 8 x 8, current 3286 x 1437, maximum 8192 x 8192 VGA-0 disconnected (normal left inverted right x axis y axis) LVDS-0 connected primary 1366x768+0+669 (normal left inverted right x axis y axis) 344mm x 193mm 1366x768 60.0*+ HDMI-0 connected 1920x1080+1366+0 (normal left inverted right x axis y axis) 600mm x 340mm 1920x1080 60.0*+ 59.9 50.0 30.0 25.0 24.0 60.0 50.0 1680x1050 60.0 1440x900 59.9 1280x1024 75.0 60.0 1280x960 60.0 1280x800 59.8 1280x720 60.0 59.9 50.0 1152x864 75.0 1024x768 75.0 70.1 60.0 800x600 75.0 72.2 60.3 56.2 720x576 50.0 720x480 59.9 640x480 75.0 59.9 59.9 480x576 50.0 480x480 59.9 I have proprietary drivers installed on my machine, here's the info about the monitor from nvidia-settings (Actually I don't have enough reputation to post images, so here's the text): Chip Location: Internal Signal: TDMS Connection link: Single Native resolution: 2560x1440 Refresh rate: 60.00 Hz The monitor is connected to laptop via HDMI cable, and honestly I have no idea what version it is, and what version is my HDMI output of my graphics card. I tried to find how I can figure it out on the web, but had no luck. Also my video card has only VGA and HDMI outs so I can't test neither DVI-D cable nor DisplayPort. So apparently, there's some problem over there. At least I want to know exactly what's going on. I've tried to see if it a linux-specific problem, but windows also gave me the same resolution by default. What I've already tried: Connect through VGA (stupid one, of course it gave me 1920x1080). Checked two HDMI cables (not sure if they're the same or not, as mentioned above). Played around with xrandr and adding custom modes. Didn't help. Surfed for the info a lot on the web, but couldn't get appropriate results. Actually xrandr gives me the following: ~$ cvt 2560 1440 60 # 2560x1440 59.96 Hz (CVT 3.69M9) hsync: 89.52 kHz; pclk: 312.25 MHz Modeline "2560x1440_60.00" 312.25 2560 2752 3024 3488 1440 1443 1448 1493 -hsync +vsync ~$ xrandr --newmode "2560x1440_60.00" 312.25 2560 2752 3024 3488 1440 1443 1448 1493 -hsync +vsync ~$ xrandr Screen 0: minimum 8 x 8, current 3286 x 1437, maximum 8192 x 8192 VGA-0 disconnected (normal left inverted right x axis y axis) LVDS-0 connected 1366x768+0+669 (normal left inverted right x axis y axis) 344mm x 193mm 1366x768 60.0*+ HDMI-0 connected primary 1920x1080+1366+0 (normal left inverted right x axis y axis) 600mm x 340mm 1920x1080 60.0*+ 59.9 50.0 30.0 25.0 24.0 60.0 50.0 1680x1050 60.0 1440x900 59.9 1280x1024 75.0 60.0 1280x960 60.0 1280x800 59.8 1280x720 60.0 59.9 50.0 1152x864 75.0 1024x768 75.0 70.1 60.0 800x600 75.0 72.2 60.3 56.2 720x576 50.0 720x480 59.9 640x480 75.0 59.9 59.9 480x576 50.0 480x480 59.9 2560x1440_60.00 (0x34f) 312.2MHz h: width 2560 start 2752 end 3024 total 3488 skew 0 clock 89.5KHz v: height 1440 start 1443 end 1448 total 1493 clock 60.0Hz ~$ xrandr --addmode HDMI-0 2560x1440_60.00 X Error of failed request: BadMatch (invalid parameter attributes) Major opcode of failed request: 140 (RANDR) Minor opcode of failed request: 18 (RRAddOutputMode) Serial number of failed request: 29 Current serial number in output stream: 30 What I intend to do next: Try another HDMI cable? Try HDMI to DVI-D cable? Try HDMI to DisplayPort cable? Another type of adapters? VGA to DVI-D? Buy another laptop with another graphic card. Damn. My ideas pretty much end here. Any ideas? Any explanations why it isn't working are appreciated.

  Read the article

• Cloning (mirroring) laptop display to area of external monitor display

  - by intuited

  I'm using Maverick "10.10" Meercat on a HP Pavilion tx2110. This machine has an NVidia Go6150 graphics card, and sports a 1280x800 display. I have an external monitor which can do 1280x1024 resolution. FWIW I'm using openbox as my window manager; as I understand it this shouldn't be a factor. I'd like to clone the display to the monitor, so that the size of the desktop remains at 1280x800, and there is a horizontal blank area on the external monitor. I.E. I want to avoid having to pan the display of the desktop on either monitor. So the actual resolution of the monitor would be 1280x1024, but the resolution of the section of the monitor where stuff was actually being displayed would be 1280x800. Using the nvidia-settings applet, I'm able to set up the cloned display so that the desktop size is 1280x1024 (the resolution of the external monitor), but can't find a way to instead have the desktop size stay at the resolution of the laptop's built-in display. Is this achievable? Ideally I'd like the external monitor's blank area to be at the top of the screen, i.e. for it to align the display with the bottom of the screen.

  Read the article

• How do i disable intel graphics in a hybrid graphics setup?

  - by Eshwar

  Hi, I have a Dell Vostro 3700 version A10. The relevant bits from lspci -v | grep VGA are: 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) and 01:00.0 VGA compatible controller: nVidia Corporation GT216 [GeForce GT 330M] (rev a2) so as you can see this is one of those hybrid graphics laptops. Now, I have no interest in any kind of switching. I would like to completely disable the Intel Graphics thats on the processor. I checked in the xorg.log file and it shows that the intel card is in use. from lsmod i see it uses the i915 module. I tried blacklisting that module in /etc/modprobe.d/blacklist.conf but that didn't really work because i still couldn't use the nvidia card for display. I wish there was a BIOS option to disable, but there isn't. Some people have also suggested changing the SATA mode to compatibility, but that does not work either in this case as the intel vga controller still shows up in lspci I tried setting the busid manually in the /etc/X11/xorg.conf file but it still didn't work. It gave me an error that said something along the lines of screen not detected. any bits of xorg.log that you'd like me to attach? So what I am looking for is some solution that allows me to completely disable the use of the intel vga controller. if it was blocked somehow it'd be nice. as if it were not present. Any suggestions? I am desperate here actually. Because I cannot use the HDMI port right now on my laptop for that reason. My guess is this applies to desktops that also have Core i5 processors with onchip graphics as well as dedicated graphics cards. How would they go about solving the problem?

  Read the article

• Graphic Card Installation Failure (NV 9600M GT)

  - by Georg

  I wanted to switch from 7 to Ubuntu. Now, the first thing that holds me back is the installation of the driver for my Nvidia 9600M GT. Ubuntu recommends me 4 drivers from the "Additional Driver" Section. Now, whatever driver I install, there are four things happening RANDOMLY after rebooting: The pc freezes before seeing bootup splash The pc freezes while seeing bootup splash image (ubuntu logo with the 5 dots) The pc gets into login screen and freezes instantly (Thought the unity-bar is transparent now) The pc freezes right after beeing able to login. (While this is happening the unity-bar changes from transparent to ugly-flat-style) I also tried to install the official Nvidia .run file but after exiting the X-Server, it says the driver is not compatible with the kernel and exits installation. Can somebody help me? I really wanna get rid of Windows :( But Ubuntu drives me perfectly insane. Please answer as noobish as possible. I'm an expert Windows user, but Linux is absolutely new to me. My Specs: Ubuntu 11.10 installed from USB Stick (like 100 times now :/ because I dont know how to remove the driver in recovery mode) 9600M GT 4GB Ram Intel Centrino 2 Dual Core 2.26GHz Win 7 and Ubuntu running along side. Thank you in advance, regards.

  Read the article

• What is the proper way to install the 3.4 kernel?

  - by Marcelo Ruiz

  Kernel 3.2 has an annoying error for my wireless card (rtl8192se-b) that makes the connection drop and/or prevents the card to make a connection to the wireless router. Dealing with it was very frustrating until I found out the bug was corrected in 3.4. I downloaded: linux-headers-3.4.0-030400_3.4.0-030400.201205210521_all.deb linux-headers-3.4.0-030400_3.4.0-030400.201205210521_all.deb linux-image-3.4.0-030400-generic_3.4.0-030400.201205210521_amd64.deb and installed with: sudo dpkg -i * Now the wireless works fine, but I have two problems that cannot solve. The first one is minor: plymouth would not start at all. But if I boot with the 3.2 kernel it works fine. The second one is serious: sometimes the computer won't shut down or reboot. The X server terminates but the computer shows part of my grub background and will stay there forever using 100% of the CPU. I have a Toshiba Qosmio with an Core i7 and nvidia graphic card (using nvidia-current). During one shutdown, I briefly read a message that said that the virtualbox module couldn't be unloaded from the kernel. I tried to solve this by removing and purging virtualbox and installing it back. I don't see the message anymore, but sometimes the computer won't shutdown nor reboot. Am I missing something to properly configure the new kernels? Thanks!

  Read the article

• Dell XPS 15 L502x and Ubuntu 11.04 - HDMI output

  - by Jones

  Recently I've bought my dream's notebook, a Dell XPS 15 but since then this dream became a kind of endless nightmare. I'm almost getting crazy to make my graphic card driver work properly, but it seems to be just impossible. Yes, I have a 2GB NVIDIA GeForce GT 540m (Optimus) in it! It simply doesn't work. Every time I generate the xorg.conf Ubuntu hangs on while starting up, which forces me to remove this file to be able to start the notebook with the standard graphic settings. Another problem is that the Dell XPS 15 does NOT have a VGA output, but a HDMI. So, to be able to use a second monitor I have to configure it by the NVIDIA X Server Settings, which just works if the driver is properly initialized with the xorg.conf. I've also tried to make it work with the Bumblebee, but unfortunately it didn't help me much with the HDMI output. Do you guys have any idea to solve this deadlock? Is there any way for me to use my second monitor?

  Read the article

• 12.04 LTS boot hangs at "SP5100 TCO timer: mmio address 0xfec000f0 already in use", didn't yesterday

  - by DarkIron112

  Dual-booting Windows 7 and Ubuntu 12.04 LTS. I went to reboot from Win to Ubu, and found a few interesting things. My POST screen is covered in blocks of epileptic colors until I hit GRUB, which continues when I try to boot into Ubuntu. These color blocks don't appear when I use my on-board VGA, so I'll just attribute to that. Grub dimensions are swapped (card vs onboard, probably), but, when interfacing with onboard VGA, the Grub Timeout Counter works and when using my card, it does not (see "[!!!]" below for more information) Booting into Ubuntu directly causes the error: SP5100 TCO timer: mmio address 0xfec000f0 already in use Booting into recovery mode, meanwhile, and then "resuming normal boot" gets me to the desktop without native 1440x900 resolution and graphic drivers can't tell the monitor it's looking at (I assume this is because it's not a full graphic boot, and as it says, some drivers won't run?) [!!!] When I reboot after going into recovery mode, the countdown timer works ONCE, puts me back into default ubuntu boot, and then does not work again until after another recovery-mode boot. Windows 7 can boot perfectly with no issues whatsoever from epilepsy color blocks or driver detection. This makes me wonder /why/ the POST screen can't handle my video card anymore. Amidst all the diagnostics, I opened my case and re-seated the videocard securely, ensuring it wasn't a loose connection-- But this did nothing to help me. Hardware I am running an NVidia GeForce GTX 8800 video card in a PCI slot. I have 4.8GiB memory, an AMD Athlon II Quad-core 640 Processor, on an MSI K9N6GM Series Mobo. Onboard video is an NVidia GeForce MCP61(V/S/P) card. Note: I did not have any of these problems yesterday, and I have been using Ubuntu intensively for a week, though it's been working flawlessly for months. I've recently been using it to mod my Android phone, perhaps I messed something up in the file system?

  Read the article

• Drivers for Ubuntu 13.10 [on hold]

  - by Fernando De Souza Martins

  I just installed Ubuntu 13.10, my screen resolution is not fitting my screen as the ubuntu interface is all around stretching over the screen, so i thought i might install nvidia's driver that i know can let me adjust the exact resolution i need. So i began a 2 hour quest, i downloaded the driver hoping i would have a wizard to instal it, but yeah, so i tried to do a bit of research and i found that feature, i think its called in english additional drivers, but it wont show the nvidia drivers, i tried the terminal, but once i write the commands i found it asks for a password but i cant type anything once the password is asked. So, my question, obviously, how do i install this driver? I am not sure if this is appropriate, but why doesnt ubuntu have a wizard to install things? I feel like im working for the OS, when it should be the other way around, but i love the concept of linux, so im pushing forward and trying to use it. Another thing is, i had to install a bunch of drivers and applications for the drivers in windows, do i need to install any other driver? I cant change my mouse's sensibility in the os, it seems, so how do i do it? I'm sorry i'm asking all of this, but it seems necessary.

  Read the article

• 10.10 boots to command line login prompt

  - by greggory.hz

  I recently installed Ubuntu 10.10 on a computer that was previously running 10.04 (that worked fine). Now, each time I boot up, it starts up in a command line login prompt. I can login and it stays at the command line (as expected). I can then manually start gdm with sudo start gdm and it works fine. I can also enable compiz (using proprietary nvidia drivers) so I'm reasonably confident that it's not a driver problem (at least not in the sense that the drivers just flat out aren't working). Interestingly, if I leave it at the command prompt without logging in, after about 5 or 10 minutes, gnome starts up on its own. I'm not sure what is causing this. This is what dmesg | tail gives me after a manual start of gdm: [ 15.664166] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 270.18 Tue Jan 18 21:46:26 PST 2011 [ 15.991304] type=1400 audit(1297543976.953:11): apparmor="STATUS" operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" pid=990 comm="apparmor_parser" [ 16.606986] eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1 [ 18.798506] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0 [ 26.740010] eth0: no IPv6 routers present [ 90.444593] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0 [ 189.252208] audit_printk_skb: 21 callbacks suppressed [ 189.252213] type=1400 audit(1297544150.218:19): apparmor="STATUS" operation="profile_replace" name="/usr/lib/cups/backend/cups-pdf" pid=1876 comm="apparmor_parser" [ 189.252584] type=1400 audit(1297544150.218:20): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/cupsd" pid=1876 comm="apparmor_parser" [ 351.159585] lo: Disabled Privacy Extensions

  Read the article

• Change X settings to boot into laptop with non working screen using an external monitor

  - by dassouki

  My laptop committed suicide. Is there a way I can boot into my ubuntu using an external screen? Ubuntu 10.10 video: Nvidia 9500 gm i think I can get dual screen upto and until the ubuntu login screen at which point it goes back into laptop display only. Then I can just type and enter my password. The system (i assume boots into ubuntu) but I got no way of going onto the x or nvidia settings to change my display to external monitor EDIT well I booted into terminal using control shift F1 i think, and now I'm trying to reporgram x.org, but strangely it seems bland with not a lot of settings in it EDIT 2 xrandr returns "Can't open display" EDit 3 after some messing around with xrandr and xinit ... my x.org only displays one monitor instead of two in its settings although both, i.e. the laptop and external screens are both connected. EDIT 4 it seems that x.org now has a "screen" and "monitor" section, I can't seem to be able to boot linux into monitor. I get a "Monitor is not a valid keyword" in this subsection

  Read the article

• Setting up dual monitors, Xorg.conf issues

  - by JTS

  I just got a new computer (W520, Graphics card nVidia GF106 [Quadro 2000]) and installed ubuntu on it using wubi. I have everything working, so I wanted to set it up to be able to use two monitors with an extended screen. I figured I had to edit Xorg.conf, but the file didnt exist. So I tried to create it by booting in recovery mode, and executing Xorg -configure but I am getting these errors: (EE) Failed to load module "vmwgfx" (module does not exist, 0) (EE) vmware: Please ignore the above warnings about not being able to load module/driver vmwgfx (++) Using config file: "/root/xorg.conf.new" (==) Using system config directory "/usr/share/X11/xorg.conf.d" (EE) [drm] No DRICreatedPCIBusID symbol Number of created screens does not match number of detected devices. Configuration failed. ddxSigGiveUp: Closing log Any idea how I can get Xorg -configure to work, so that I can have an xorg.conf file that I can edit to enable twinview? EDIT: Another way I could ask the same question to solve this problem is, why can't I boot with an xorg.conf file generated by nvidia-xconfig? Is there something in the generated xorg.conf file that might need editing?

  Read the article

• Fix for poor hd playback for 11.04 upwards

  - by mark kirby

  Hi guys ive seen loads of posts on this site about poor 720/1080p playback in recent ubuntu versions I had this problem and fixed it so I thought id share it with everyone.... 1 install mplayer 2 install smplayer frontend {in software center} 3 open smplayer 4 go to "OPTIONS" then "PREFRENCES" then "GENRAL" 5 if you have a nvidia card choose "OUTPUT DRIVER" and select "VDPAU" {for ATI or AMD choose xv (0 - ATI Radeon AVIVO video) I dont know if this will work as my card is nvidia but it should) 6 go to performance on the left hand side and set both local and streaming cache to 99999 (this may also fix dvd playback if you set that cache aswell} 7 check the box for "ALLOW HARD FRAME DROP" and set "LOOP FILTER" to skip only on HD 8 Set the "THREDS FOR DECODING OPTION TO THE NUMBER OF CORES YOUR CPU HAS IF YOU HAVE MORE THAN ONE CPU ADD UP ALL THE CORES FOR BEST PERFORMANCE" 9 Enjoy you HD movies again on ubuntu...... I have a pretty avrage machine heres my spec.... 2x Pentium 4 ht 3 ghz Stock dell power and motherboard GFORCE 310 HDMI 24 inch full HD tv as a monitor so any one with dule core cpu should have no problems getting this to work. hope this helps someone out.

  Read the article

• How can I set my resolution to 1280x1024 on an Acer Aspire Revo 3700?

  - by torbengb

  I've just set up a new nettop computer (Acer Aspire Revo 3700: CPU:Atom D525, GPU:Nvidia ION2). I've just made a clean install of Ubuntu 10.10 using the standard USB pendrive method. Almost everything works OK, but the graphics are not OK: the recommended Nvidia driver is activated but the monitor is not detected, so the resolution is wrong. How can I make Ubuntu detect my monitor? How can I get the proper resolution (1280x1024) in Ubuntu? I know that my monitor is not a CRT but an LCD: it's a BenQ, model T905, with 1280x1024 resolution at 60Hz, connected via a normal VGA cable. DVI or HDMI is not an option. When I go to SystemPrefsMonitors, I get: It appears that your graphics driver does not support the necessary extensions to use this tool. Do you want to use your graphics driver vendor's tool instead? YES NO If I say NO then I get a window: or for YES I get this: In both cases I don't see that I can fix this problem. The main reason for getting this new computer was that I was sick of having graphics problems on the old one with a very ugly solution that didn't give me hardware support - but at least I got the resultion. Why is this so difficult... sigh!

  Read the article

• GeForce and Radeon: what is present condition of opensource and proprietary drivers?

  - by Septagram

  So, it'm about to buy a fresh videocard. Since I do most of my stuff on Linux, I wonder how well will either videocard perform. I recently had a good experience with GeForce 6600 with proprietary drivers and a less than satisfactory experience with Radeon 9000 a while ago. From my experience, proprietary drivers for GeForce used to work very well, while proprietary drivers for Radeon failed miserably. And opensource drivers were sloooow. A few months ago I found out that ATI opened their specifications, and a work on fully featured opensource driver is in progress. I prefer to use free software whenever possible, with the exception of games, so, if that driver is fast enough, feature-rich enough and reliable enough I'd very much like to try it out. I wish I could say that if I can just to basic things, like watch video, heavily use compiz and work with simple applications, this may be enough. I do most of my gaming under Windows anyway. However, there is a good chance I'll go into indie game development in a few months fulltime, so it should also be able to run not-so-very-demanding games (say Nexuiz). But if it isn't, I'd like to know, what to expect from proprietary drivers. Do recent proprietary drivers from NVIDIA and ATI work well? Are ATI drivers just as easy to install on Ubuntu as are NVIDIA drivers?

  Read the article

• 13.10 Saucy login issues; black screen, loop, and freeze

  - by user135598

  Once upgraded to I 13.10 I was not able to get past the login screen. I had the black screen. Also; I can not log on with low graphics mode from recovery either. It makes no difference if I try default graphics driver or not. Then after running sudo install -f from recovery root prompt I got a login loop. I have purged fglrx, fglrx-legacy, and nvidia-current. I updated my repository with xorg-edgers and reinstalled nvidia-current. Now it semi-freezes at the login screen when I try to log on as my normal user. I say 'semi' because I can still use my mouse to click on the upper right hand Ubuntu logo and Shut Down or Restart the PC. I still cannot log on with my user name, but I can through the Guest login. While logged in as Guest I added a new user account with administrative privileges. I CAN log into this account without problem and from here am able to see that my .dmrc file in my original account reads: [Desktop] Session=XBMC I have changed 'Session=XBMC' to 'Session=ubuntu' and rebooted, but to no avail. The file resets itself and makes a backup of my changes. Any help would be greatly appreciated.

  Read the article

• How can I get SLI working with 295.40?

  - by Steve

  I've been doing a lot of googling these last few hours and I'm not having much luck. Perhaps I don't know exactly what I am looking for. I just recently installed Ubuntu 12.04LTS x86_64. Looks beautiful! I have two GTX470's in SLI, and I am finally migrating my desktop over given the hopeful gaming support as of late. My laptop has been enjoying multiple distros of Ubuntu for a couple years now. However, new problems come with unexplored territory, here. At first, I only had one working monitor of my two. Over on nvidia-xconfig I fixed that, but the only solution that actually worked was twinview. Just recently I read here that twinview is not compatible with SLI. Sweet. When I try to tell it, oh hey, use a separate XScreen, configure it the way I want it, click save to configuration file, enter my password, then a sudo restart lightdm, it's broken. One screen blacks or whites out (Couldn't tell you the specific conditions for each, I'm dubious at this point,) and I get this huge error dialogue box upon login. Something about incompatible resolutions if I remember right. Though I am sure I set the resolutions for each screen correctly. Anyway, when I try to enable SLI (sudo nvidia-xconfig --sli=On) despite the fact it hates twinview, unity breaks. The sidebar is there, but only one screen works, the mouse is trapped running along the left edge of it, and the background of the sidebar is a solid blue. Anyway, this ended up being entirely too verbose, I'm sorry, but could anyone part some wisdom please? It would be appreciated!

  Read the article

• How to ensure nvidia_current module loads during boot

  - by Aras

  I am running Ubuntu 12.10 on an Asus G75V laptop with nvidia gforce GTX 660M. I first run 12.04 on this machine and was able to install nvidia_current drivers from swat ppa: sudo apt-add-repository ppa:ubuntu-x-swat/x-updates sudo apt-get update sudo apt-get install nvidia-current This worked in 12.04 and after rebooting the machine my graphics where working properly. After upgrade to 12.10 however, the machine boots into a low resolution desktop which I can not really interact with. I suspect this is due to the driver not being loaded properly. To fix this, I have to switch to ctrl+alt+F1 session and manually load the nvidia_current module and restart the desktop manager: sudo modprobe nvidia_current sudo service lightdm restart Now everything works fine again. However, I would like not to have to do this every time I reboot the machine. I also dont want to hack an script to do this on load. Basically, if things are setup currectly, the nvidia_current driver which is installed should load. How can I make sure nvidia_current driver module loads properly when system starts?

  Read the article

< Previous Page | 20 21 22 23 24 25 26 27 28 29 30 31  | Next Page >