Search Results

Search found 5744 results on 230 pages for 'power cords'.

Page 24/230 | < Previous Page | 20 21 22 23 24 25 26 27 28 29 30 31  | Next Page >

  • PC doesn't POST with a certain model of PSU

    - by Core Xii
    I have this PC with an Asus P5N32-E SLI motherboard and an Intel Q6600 CPU. I got a new RX-5300 PSU, but it didn't work. The motherboard power LED is on fine When I switch power on, the PC powers up briefly (0.5-1 sec) then shuts down From there on out when I switch power on, it stays on, all fans and components seem to be receiving power, but the motherboard won't POST. No video output, no PC speaker beeps, nothing If I turn the hard switch on the PSU off and then back on again, go to step 2; The PC turns on and then off immediately again, and on subsequent power-ups it stays on but won't POST I disconnected every component but the motherboard, CPU and PSU. Still nothing. I tried three other models of PSU on this PC, both of higher (600) and lower (<300) wattage than the 530 on the RX-5300 and they all work fine. At this point I was convinced the PSU was faulty so I returned it. When the replacement arrived, it behaved exactly the same. So two different units of RX-5300 both with the same symptoms, neither working with this motherboard + CPU. Yet, three other models of PSU work perfectly fine. The PC store couldn't reproduce my problem with the returned PSU. I tried resetting the CMOS with the jumper. I tried with both the 4 and 4+4 (with and without the extra +4 connected) CPU connectors (curiously the RX-5300 comes equipped with both). Could it be a statistical probability that I get two units of the same model of PSU that are faulty in the exact same manner? Could the RX-5300 model itself be somehow incompatible with this motherboard? I was under the impression that PSUs were pretty much universal so long as you have the wattage. Could the motherboard be broken in some such a way as to work with certain PSUs but not others? What's going on here?

    Read the article

  • Which type of motherboard i should buy and why?

    - by metal gear solid
    If budged is not a problem. I just need best performance with less power consumption. I can purchase any cabinet , power supply and Motherboard. Is Power supply has any relation with Form factor? Is the size of motherboard and number of Slots only difference between all form factors? Is there any differences among form factors, related to performance of motherboard? Is bigger in Size (ATX) motherboard always better? Is it so smaller in Size motherboard will consume less power? What are pros and cons of each Form factor? What there are so many Form factor were created?

    Read the article

  • APC UPS-5000 Power off remote servers

    - by Vishal
    Hi there, I have a UPS connected via the serial port to a server using PowerChute Business Edition. If a power outage occurs I would like this server to start shutting down all other servers within the network. Is there dedicated software to do this? I was thinking of creating a command file which runs a .bat file to run shut down commands to each server (using PSExec). I can set PowerChute to run this command file when a power failure occurs. Is there not anything APC provide which has this functionality and is more efficient than writing a .bat file to do this? Thanks,

    Read the article

  • Any reasonable UPS for a Desktop PC, just to shut it down?

    - by Michael Stum
    While I do have a surge protector to protect against overvoltage (hopefully), I have nothing against undervoltage. When a lightning storm hits, I had the lights flickering at some point. The PC continued to run, but it got me thinking of getting a UPS as a way to a) have a clean 120V/60Hz power source and b) have a way to shut down the PC in case something bad happens. I heard not all UPS' protect against power spikes, so I wonder if someone has a recommendation? It does not need to keep the PC on for a long time if the power goes out, it's good enough if it shuts down the PC after 5 minutes or so. There are 2 PCs connected. One is a Core i7-860 with a Radeon 5870 running Windows 7 Ultimate (so quite power hungry. It uses a 600W PSU but I have no measurements of the actual usage), the other one is a Windoes Home Server, running WHS/Windows Server 2003. Any recommendations in the low-price segment?

    Read the article

  • How can I tell if my UPS is functioning properly or not for my PC?

    - by prabha
    For the last two days, my Uninterruptable Power Supply (UPS) has failed to produce the actual back up. So, I charged it for 24hrs and again checked that when the power failed my PC was automatically shut down. But in the time of power no supply from ups bt .......is my ups is working properly or not else there is direct power. It will cause any harm to my pc. my questions are..... Is the UPS functioning properly or not? If not, then will it harm my pc? If it is functioning, will it regulate direct power to pc without any cause? Is my UPS battery not working? What should I do to make my UPS batteries last for at least a year? I am using FRONTECH UPS 600va (Warranty for both ups and battery is expired) I already changed the battery 8 months previously. Note from editor: Tried to make as much sense of this question as I could. I hope I didn't alter the meaning in any way.

    Read the article

  • Which type of motherboard i should by and why?

    - by metal gear solid
    If budged is not matter. I just need best performance with less power consumption. I can purchase any cabinet , power supply and Motherboard. Is Power supply has any relation with Form factor? Is the size of motherboard and number of Slots only difference between all form factors? Is there any difference related to performance of motherboard? Is bigger in Size (ATX) motherboard always better?

    Read the article

  • Which type of Form factor (motherboard) i should buy and why?

    - by metal gear solid
    If budged is not a problem. I just need best performance with less power consumption. I can purchase any cabinet , power supply and Motherboard. Is Power supply has any relation with Form factor, should i purchase PSU according to Form factor of motherboard? Is the size of motherboard and number of Slots only difference between all form factors? Is there any differences among form factors, related to performance of motherboard? Is bigger in Size (ATX) motherboard always better? Is it so smaller in Size motherboard will consume less power? What are pros and cons of each Form factor? What there are so many Form factor were created?

    Read the article

  • Why does Ubuntu (and other ubuntu based distros like lubuntu and linux mint) randomly shutdown on my laptop?

    - by Imran
    I have a lenovo g555 laptop and whenever I try and boot a ubuntu based distro off a usb, it randomly shuts off my PC (Not like a normal shutdown with shutdown loading screen but a like a sudden hard power off). This problem occurs even if I have installed the distro on my harddrive. In the past I've been able to use the distro for 10 min or so before it would it would do this. Now with the latest distros, It randomly pwers off even before it has fully booted up. My hardware specs are on this website.

    Read the article

  • FrankenUPS Hack Turns a Server UPS into a Whole House UPS

    - by Jason Fitzpatrick
    This well documented build guide showcases the process of turning a rack-mounted UPS battery device intended for a server bank, into a super-charged whole-house UPS system with a massive 14 hours of backup juice. It’s a very ambitious build and, due to the work required in the main circuit breaker of your home, we highly recommend only those experienced with electrical work undertake the project. That said, it’s a really clever bit of recycling that yielded an impressive half-day worth of backup power. Hit up the link below for the detailed build log. FrankenUPS [via Hack A Day] The Best Free Portable Apps for Your Flash Drive Toolkit How to Own Your Own Website (Even If You Can’t Build One) Pt 3 How to Sync Your Media Across Your Entire House with XBMC

    Read the article

  • Jupiter in Ubuntu 13.10 (Laptop Overheating)

    - by Daniel Pacheco
    I was wondering if Jupiter (Interface for display, power and device control) will work in Ubuntu 13.10, because my laptop (Toshiba Satellite C855D, AMD A6-4400M with Radeon HD Graphics running Ubuntu 13.04 x64) keeps overheating, I tried some other tools, like laptop-mode-tools or TLP, none of those work, not at all. Jupiter was the only option and it's supposedly discontinued, the version I'm using is being maintained by JoliCloud team, but they told me they're not sure if it will work with 13.10... If it doesn't work, I'm definitely not upgrading, since overheating is a major issue for me... Thanks in advance!

    Read the article

  • How do you limit root partition disk access to allow drive to go into stanby mode?

    - by Casey
    When there are no users on my system, I would like the hard disk to spindown to low-power state. I realize that this might not be 100% achievable for a straight 24 hours, but it seems reasonable that the system could remain idle for a few hours at a time when it is not in use. My system is headless and running a limited number of services. The primary services are: exim4, mythtv-backend, nfs, samba, cups, apt-cacher-ng Assume that drives are already enabled to go into standby mode. Also, its not acceptable to increase the write-back timeout, since my system is not on a UPS.

    Read the article

  • Modify actions when battery is critically low?

    - by Bjarke Freund-Hansen
    I am running ubuntu (not xubuntu!) and am using xfce4 on my laptop. When my laptop battery is critically low, ubuntu/xfce4 performs some action (perhaps hibernate?) which causes my laptop to shut down. However when I start it again, it never comes up. I don't even get BIOS or anything on the screen, it is completely black. The only way to get it back up is to take it apart, remove the internal cmos battery as well as the main battery, wait a few minutes, and put it back together. Obeviously this is not optimal. How do I disable all actions when the battery is critically low? I would rather have it run out of power, than ending up in this error condition. Thanks in advance. :)

    Read the article

  • suspend not working

    - by Eric
    I am running 13.10 on an ASUS 101-SE netbook. Under "power settings" I have selected suspend when inactive for 10 minutes and suspend when lid is closed. I get a warning when inactive that the computer will suspend due to inactivity, but it does not suspend either from that condition or when closing the lid. I seem to be getting multiple suspend messages as I need to click "cancel" or "OK" many times to get the error window to close when it has been inactive for some time. Anyone have any tips? Thank you.

    Read the article

  • Laptop resumes from suspend while lid is closed

    - by Gus
    I have a Dell Studio 15 and I am running Ubuntu 10.10. When I close my lid or select the suspend option, the machine suspends as indicated by the slowly pulsing power indicator. I'll put the machine in my bag and after a while it seems that the machine resumes, at least I think. When ever I go to get it, it's overheated and the system cannot resume. I am guessing that the processor resets in this overheat condition, but heat is still generated. This has happened about three times and I'm getting worried that I'll end up damaging the machine. How can I diagnose why the system is resuming from suspend? Can I force it to never resume from suspend if the lid is down?

    Read the article

  • How do I prevent an external monitor from shutting off when closing my laptop lid?

    - by Thom
    I've seen this issue on previous versions of Ubuntu, but not on 12.04 and some of those are resolved bugs, so I'm asking again. I've set up power management so that, when plugged in, my laptop does nothing when the lid is closed. I do this so that I can use as a desktop with my external monitor with the screen closed and the laptop scurried away from my desktop. I tried turning off the laptop monitor to see if that made a difference, but it doesn't. The problem is that closing the lid still shuts off my external monitor. What can I do to prevent this?

    Read the article

  • How to close lid without triggering standby one time only

    - by Ian Mackinnon
    Related: How can I tell Ubuntu to do nothing when I close my laptop lid? I have my laptop set to activate standby when I close the lid. I want to keep this as the default for both battery and AC power. But occasionally I want to close the lid without triggering standby (eg. while just listening to audio). Is there someway I can tell Ubuntu, "I'm going to close the lid now. Don't stand by this time", without altering the defaults (because I almost always forget to change them back).

    Read the article

  • Ubuntu reports low battery capacity on my Dell Vostro

    - by Jeff
    I have a Dell Vostro 1500. Before I wiped Windows XP off my hard drive in 2009, I had a full ~7 hrs battery capacity. I installed Ubuntu 9, and the capacity immediately dropped to about 27% (and has since decreased to about 11%). I couldn't figure out what to do, so I've just lived with the 20-30 minute battery life ever since. I upgraded to Ubuntu 10, and the issue remained. I wiped my hard drive clean again and installed Ubuntu 11, and the issue still remains. I tried what they told me in the forum here, but it didn't do anything. Is it possible for a battery to suddenly lose most of its capacity?? Or is there a bug in the power management software?

    Read the article

  • CPU frequancy stuck at 1.20 GHz using TLP?

    - by Rana Muhammad Waqas
    I have installed TLP for power optimization on Ubuntu 13.10. Instructions I start computer its running fine I can change the CPU frequencies to whatever I want, but after some time it stuck on minimum frequency 1.20 GHz, I cant change that to anything else. I have tried to stop it by using sudo tlp stop but it doesn't stop. Tried even to kill its process sudo killall tlp but it seems they have a different name of process of that so i am not sure what to do now. I reported to the linrunner but cant seem to find a solution

    Read the article

  • Energy saving with two batteries (Gigabyte S1080 and similar)

    - by user37155
    my today question is: how do I manage a tablet (Gigabyte 1080) with an additional battery in Ubuntu ? The control bar shows two separate batteries but starts to suck all the energy from the secundary battery, not leaving any power in it and ruining it (if I don't remove it earlier), and then starts with the primary battery. Here you find a description of the secundary battery: http://www.gigabyte.com/products/product-page.aspx?pid=3837#kf Do you have some solutions for a more confortable use of te device, with windows-like drivers maybe ? Is there a graphical tool to manage two batteries in Linux, in order not to ruin them, and possibly to save energy with them ? Many thanks and greetings, Francesco

    Read the article

  • How Is My Computer Able to Restart Itself?

    - by Jason Fitzpatrick
    It’s such a common place activity that most of us have likely never stopped to even think about it: the automatic restart. Whether user or application-initiated, what exactly happens when your computer cycles its own power? Today’s Question & Answer session comes to us courtesy of SuperUser—a subdivision of Stack Exchange, a community-drive grouping of Q&A web sites. How Hackers Can Disguise Malicious Programs With Fake File Extensions Can Dust Actually Damage My Computer? What To Do If You Get a Virus on Your Computer

    Read the article

  • Is it save to configure "Shutdown" on "When laptop lid is closed" ?

    - by Takkat
    To setup a laptop owned by a complete PC novice any settings that may become hard to tackle remotely need to be avoided. The laptop will be administrated via SSH. One thing in my list are problems arising from improper wake-ups from suspend or hibernate as they may also affect network accessibility. This is why I thought setting up power management to "shutdown" on closing the laptop lid could be a good idea. However I am not sure if this is a safe way to do. What problems in addition to software not closing properly (and thus not saving their data) could I be faced if I proceeded as planned?

    Read the article

  • Is it safe to configure "Shutdown" on "When laptop lid is closed" ?

    - by Takkat
    To setup a laptop owned by a complete PC novice any settings that may become hard to tackle remotely need to be avoided. The laptop will be administrated via SSH. One thing in my list are problems arising from improper wake-ups from suspend or hibernate as they may also affect network accessibility. This is why I thought setting up power management to "shutdown" on closing the laptop lid could be a good idea. However I am not sure if this is a safe way to do. What problems in addition to software not closing properly (and thus not saving their data) could I be faced if I proceeded as planned?

    Read the article

  • Xubuntu fails to stay awake when the machine is under load

    - by Alex
    I have the following problem with a fresh install of Xubuntu 12.04: I set up power management options so as to send the machine to sleep after it's been idle for a while. My intention was to have it finish some lengthy numbercrunching and then fall asleep late at night when nobody's present to shut it down. What actually happened, however, is that the machine goes to sleep whenever the desktop session has been idle for the specified amount of time, and it does not seem to care at all about CPU load, and I had to disable sleep altogether. Is there any way to fix this?

    Read the article

< Previous Page | 20 21 22 23 24 25 26 27 28 29 30 31  | Next Page >