Search Results

Search found 5878 results on 236 pages for 'sim card'.

Page 24/236 | < Previous Page | 20 21 22 23 24 25 26 27 28 29 30 31  | Next Page >

• PCIe network card deactivate DVI output (but NOT VGA output) on Shuttle SG41J1+

  - by wazoox

  It's all in the title :) Inserting a network card (or any other PCIe card, RAID controller, SAS, etc ) in the PCIe 16x slot of the Shuttle SG41J1 deactivate the DVI output. The VGA output still works fine. Shuttle support says that it's a chipset limitation (G41 + ICH7), but that doesn't make sense to me : the VGA and DVI share the same hardware but the D/A converter stage. Does anyone think that there may be some solution to this conundrum? Can a future BIOS update solve the problem?

  Read the article

• Cant see my wireless internal card on BackTrack 5

  - by Tomer

  I have BackTrack 5 R3 installed on VMware and its on bridged connection so it gets its own ip on my network and it works I get internet connection but there is no ethernet cable connected yet somehow when I do iwconfig I cant see wlan0 and no other wireless card but etho is connected to the network somehow.... cant it be that eth0 is my wireless card which somehow misconfigured? Its an intel centrino advanced n 6205

  Read the article

• Wireless card power management

  - by penner

  I have noticed that when my computer in plugged in, the wireless strength increases. I'm assuming this is to do with power management. Is there a way to disable Wireless Power Management? I have found a few blog posts that show hacks to disable this but what is best practice here? Should there not be an option via the power menu that lets you toggle this? EDIT -- FILES AND LOGS AS REQUESTED /var/log/kern.log Jul 11 11:45:27 CoolBreeze kernel: [ 6.528052] postgres (1308): /proc/1308/oom_adj is deprecated, please use /proc/1308/oom_score_adj instead. Jul 11 11:45:27 CoolBreeze kernel: [ 6.532080] [fglrx] Gart USWC size:1280 M. Jul 11 11:45:27 CoolBreeze kernel: [ 6.532084] [fglrx] Gart cacheable size:508 M. Jul 11 11:45:27 CoolBreeze kernel: [ 6.532091] [fglrx] Reserved FB block: Shared offset:0, size:1000000 Jul 11 11:45:27 CoolBreeze kernel: [ 6.532094] [fglrx] Reserved FB block: Unshared offset:f8fd000, size:403000 Jul 11 11:45:27 CoolBreeze kernel: [ 6.532098] [fglrx] Reserved FB block: Unshared offset:3fff4000, size:c000 Jul 11 11:45:38 CoolBreeze kernel: [ 17.423743] eth1: no IPv6 routers present Jul 11 11:46:37 CoolBreeze kernel: [ 75.836426] warning: `proftpd' uses 32-bit capabilities (legacy support in use) Jul 11 11:46:37 CoolBreeze kernel: [ 75.884215] init: plymouth-stop pre-start process (2922) terminated with status 1 Jul 11 11:54:25 CoolBreeze kernel: [ 543.679614] eth1: no IPv6 routers present dmesg [ 1.411959] ACPI: Power Button [PWRB] [ 1.412046] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1 [ 1.412054] ACPI: Sleep Button [SLPB] [ 1.412150] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2 [ 1.412765] ACPI: Lid Switch [LID0] [ 1.412866] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3 [ 1.412874] ACPI: Power Button [PWRF] [ 1.412996] ACPI: Fan [FAN0] (off) [ 1.413068] ACPI: Fan [FAN1] (off) [ 1.419493] thermal LNXTHERM:00: registered as thermal_zone0 [ 1.419498] ACPI: Thermal Zone [TZ00] (27 C) [ 1.421913] thermal LNXTHERM:01: registered as thermal_zone1 [ 1.421918] ACPI: Thermal Zone [TZ01] (61 C) [ 1.421971] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 1.421986] ACPI: Battery Slot [BAT0] (battery present) [ 1.422062] ERST: Table is not found! [ 1.422067] GHES: HEST is not enabled! [ 1.422158] isapnp: Scanning for PnP cards... [ 1.422242] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 1.434620] ACPI: Battery Slot [BAT0] (battery present) [ 1.736355] Freeing initrd memory: 14352k freed [ 1.777846] isapnp: No Plug & Play device found [ 1.963650] Linux agpgart interface v0.103 [ 1.967148] brd: module loaded [ 1.968866] loop: module loaded [ 1.969134] ahci 0000:00:1f.2: version 3.0 [ 1.969154] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 1.969226] ahci 0000:00:1f.2: irq 45 for MSI/MSI-X [ 1.969277] ahci: SSS flag set, parallel bus scan disabled [ 1.969320] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 3 Gbps 0x23 impl SATA mode [ 1.969329] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ems sxs apst [ 1.969338] ahci 0000:00:1f.2: setting latency timer to 64 [ 1.983340] scsi0 : ahci [ 1.983515] scsi1 : ahci [ 1.983670] scsi2 : ahci [ 1.983829] scsi3 : ahci [ 1.983985] scsi4 : ahci [ 1.984145] scsi5 : ahci [ 1.984270] ata1: SATA max UDMA/133 abar m2048@0xf1005000 port 0xf1005100 irq 45 [ 1.984277] ata2: SATA max UDMA/133 abar m2048@0xf1005000 port 0xf1005180 irq 45 [ 1.984282] ata3: DUMMY [ 1.984285] ata4: DUMMY [ 1.984288] ata5: DUMMY [ 1.984292] ata6: SATA max UDMA/133 abar m2048@0xf1005000 port 0xf1005380 irq 45 [ 1.985150] Fixed MDIO Bus: probed [ 1.985192] tun: Universal TUN/TAP device driver, 1.6 [ 1.985196] tun: (C) 1999-2004 Max Krasnyansky <[email protected]> [ 1.985285] PPP generic driver version 2.4.2 [ 1.985472] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.985507] ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.985534] ehci_hcd 0000:00:1a.0: setting latency timer to 64 [ 1.985541] ehci_hcd 0000:00:1a.0: EHCI Host Controller [ 1.985626] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1 [ 1.985666] ehci_hcd 0000:00:1a.0: debug port 2 [ 1.989663] ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported [ 1.989690] ehci_hcd 0000:00:1a.0: irq 16, io mem 0xf1005800 [ 2.002183] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00 [ 2.002447] hub 1-0:1.0: USB hub found [ 2.002455] hub 1-0:1.0: 3 ports detected [ 2.002607] ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 2.002633] ehci_hcd 0000:00:1d.0: setting latency timer to 64 [ 2.002639] ehci_hcd 0000:00:1d.0: EHCI Host Controller [ 2.002737] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 2.002775] ehci_hcd 0000:00:1d.0: debug port 2 [ 2.006780] ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported [ 2.006806] ehci_hcd 0000:00:1d.0: irq 23, io mem 0xf1005c00 [ 2.022161] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00 [ 2.022401] hub 2-0:1.0: USB hub found [ 2.022409] hub 2-0:1.0: 3 ports detected [ 2.022567] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.022599] uhci_hcd: USB Universal Host Controller Interface driver [ 2.022720] usbcore: registered new interface driver libusual [ 2.022813] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 2.035831] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.035844] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.036096] mousedev: PS/2 mouse device common for all mice [ 2.036710] rtc_cmos 00:07: RTC can wake from S4 [ 2.036881] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0 [ 2.037143] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs [ 2.037503] device-mapper: uevent: version 1.0.3 [ 2.037656] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected] [ 2.037725] EISA: Probing bus 0 at eisa.0 [ 2.037729] EISA: Cannot allocate resource for mainboard [ 2.037734] Cannot allocate resource for EISA slot 1 [ 2.037738] Cannot allocate resource for EISA slot 2 [ 2.037741] Cannot allocate resource for EISA slot 3 [ 2.037745] Cannot allocate resource for EISA slot 4 [ 2.037749] Cannot allocate resource for EISA slot 5 [ 2.037753] Cannot allocate resource for EISA slot 6 [ 2.037756] Cannot allocate resource for EISA slot 7 [ 2.037760] Cannot allocate resource for EISA slot 8 [ 2.037764] EISA: Detected 0 cards. [ 2.037782] cpufreq-nforce2: No nForce2 chipset. [ 2.038264] cpuidle: using governor ladder [ 2.039015] cpuidle: using governor menu [ 2.039019] EFI Variables Facility v0.08 2004-May-17 [ 2.040061] TCP cubic registered [ 2.041438] NET: Registered protocol family 10 [ 2.043814] NET: Registered protocol family 17 [ 2.043823] Registering the dns_resolver key type [ 2.044290] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4 [ 2.044336] Using IPI No-Shortcut mode [ 2.045620] PM: Hibernation image not present or could not be loaded. [ 2.045644] registered taskstats version 1 [ 2.073070] Magic number: 4:976:796 [ 2.073415] rtc_cmos 00:07: setting system clock to 2012-07-11 18:45:23 UTC (1342032323) [ 2.076654] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 2.076658] EDD information not available. [ 2.302111] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2.302587] ata1.00: ATA-9: M4-CT128M4SSD2, 000F, max UDMA/100 [ 2.302595] ata1.00: 250069680 sectors, multi 16: LBA48 NCQ (depth 31/32), AA [ 2.303143] ata1.00: configured for UDMA/100 [ 2.303453] scsi 0:0:0:0: Direct-Access ATA M4-CT128M4SSD2 000F PQ: 0 ANSI: 5 [ 2.303746] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 2.303920] sd 0:0:0:0: [sda] 250069680 512-byte logical blocks: (128 GB/119 GiB) [ 2.304213] sd 0:0:0:0: [sda] Write Protect is off [ 2.304225] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.304471] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.306818] sda: sda1 sda2 < sda5 > [ 2.308780] sd 0:0:0:0: [sda] Attached SCSI disk [ 2.318162] Refined TSC clocksource calibration: 1595.999 MHz. [ 2.318169] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 2.318178] Switching to clocksource tsc [ 2.450939] hub 1-1:1.0: USB hub found [ 2.451121] hub 1-1:1.0: 6 ports detected [ 2.561786] usb 2-1: new high-speed USB device number 2 using ehci_hcd [ 2.621757] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 2.636143] ata2.00: ATAPI: TSSTcorp DVD+/-RW TS-T633C, D800, max UDMA/100 [ 2.636152] ata2.00: applying bridge limits [ 2.649711] ata2.00: configured for UDMA/100 [ 2.653762] scsi 1:0:0:0: CD-ROM TSSTcorp DVD+-RW TS-T633C D800 PQ: 0 ANSI: 5 [ 2.661486] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 2.661494] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 2.661890] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 2.662156] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 2.694649] hub 2-1:1.0: USB hub found [ 2.694840] hub 2-1:1.0: 8 ports detected [ 2.765823] usb 1-1.4: new high-speed USB device number 3 using ehci_hcd [ 2.981454] ata6: SATA link down (SStatus 0 SControl 300) [ 2.982597] Freeing unused kernel memory: 740k freed [ 2.983523] Write protecting the kernel text: 5816k [ 2.983808] Write protecting the kernel read-only data: 2376k [ 2.983811] NX-protecting the kernel data: 4424k [ 3.014594] udevd[127]: starting version 175 [ 3.068925] sdhci: Secure Digital Host Controller Interface driver [ 3.068932] sdhci: Copyright(c) Pierre Ossman [ 3.069714] sdhci-pci 0000:09:00.0: SDHCI controller found [1180:e822] (rev 1) [ 3.069742] sdhci-pci 0000:09:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 3.069786] sdhci-pci 0000:09:00.0: Will use DMA mode even though HW doesn't fully claim to support it. [ 3.069798] sdhci-pci 0000:09:00.0: setting latency timer to 64 [ 3.069816] mmc0: no vmmc regulator found [ 3.069877] Registered led device: mmc0:: [ 3.070946] mmc0: SDHCI controller on PCI [0000:09:00.0] using DMA [ 3.071078] tg3.c:v3.121 (November 2, 2011) [ 3.071252] tg3 0000:0b:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 3.071269] tg3 0000:0b:00.0: setting latency timer to 64 [ 3.071403] firewire_ohci 0000:09:00.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [ 3.071417] firewire_ohci 0000:09:00.3: setting latency timer to 64 [ 3.078509] EXT4-fs (sda1): INFO: recovery required on readonly filesystem [ 3.078517] EXT4-fs (sda1): write access will be enabled during recovery [ 3.110417] tg3 0000:0b:00.0: eth0: Tigon3 [partno(BCM95784M) rev 5784100] (PCI Express) MAC address b8:ac:6f:71:02:a6 [ 3.110425] tg3 0000:0b:00.0: eth0: attached PHY is 5784 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0]) [ 3.110431] tg3 0000:0b:00.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1] [ 3.110436] tg3 0000:0b:00.0: eth0: dma_rwctrl[76180000] dma_mask[64-bit] [ 3.125492] firewire_ohci: Added fw-ohci device 0000:09:00.3, OHCI v1.10, 4 IR + 4 IT contexts, quirks 0x11 [ 3.390124] EXT4-fs (sda1): orphan cleanup on readonly fs [ 3.390135] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078710 [ 3.390232] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 2363071 [ 3.390327] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078711 [ 3.390350] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078709 [ 3.390367] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078708 [ 3.390384] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078707 [ 3.390401] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078706 [ 3.390417] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078705 [ 3.390435] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078551 [ 3.390452] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078523 [ 3.390470] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078520 [ 3.390487] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7077901 [ 3.390551] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4063272 [ 3.390562] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4063266 [ 3.390572] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4063261 [ 3.390582] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4063256 [ 3.390592] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4063255 [ 3.390602] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 2363072 [ 3.390620] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 2360050 [ 3.390698] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 5250064 [ 3.390710] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 2365394 [ 3.390728] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 2365390 [ 3.390745] EXT4-fs (sda1): 22 orphan inodes deleted [ 3.390748] EXT4-fs (sda1): recovery complete [ 3.397636] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 3.624910] firewire_core: created device fw0: GUID 464fc000110e2661, S400 [ 3.927467] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 3.929965] udevd[400]: starting version 175 [ 3.933581] Adding 6278140k swap on /dev/sda5. Priority:-1 extents:1 across:6278140k SS [ 3.945183] lp: driver loaded but no devices found [ 3.999389] wmi: Mapper loaded [ 4.016696] ite_cir: Auto-detected model: ITE8708 CIR transceiver [ 4.016702] ite_cir: Using model: ITE8708 CIR transceiver [ 4.016706] ite_cir: TX-capable: 1 [ 4.016710] ite_cir: Sample period (ns): 8680 [ 4.016713] ite_cir: TX carrier frequency (Hz): 38000 [ 4.016716] ite_cir: TX duty cycle (%): 33 [ 4.016719] ite_cir: RX low carrier frequency (Hz): 0 [ 4.016722] ite_cir: RX high carrier frequency (Hz): 0 [ 4.025684] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. [ 4.025691] Disabling lock debugging due to kernel taint [ 4.027410] IR NEC protocol handler initialized [ 4.030250] lib80211: common routines for IEEE802.11 drivers [ 4.030257] lib80211_crypt: registered algorithm 'NULL' [ 4.036024] IR RC5(x) protocol handler initialized [ 4.036092] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 4.036188] snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X [ 4.036307] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 4.036361] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness [ 4.039006] acpi device:03: registered as cooling_device10 [ 4.039164] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input5 [ 4.039261] ACPI: Video Device [M86] (multi-head: yes rom: no post: no) [ 4.049753] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 4.050201] wl 0000:05:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 4.050215] wl 0000:05:00.0: setting latency timer to 64 [ 4.052252] Registered IR keymap rc-rc6-mce [ 4.052432] input: ITE8708 CIR transceiver as /devices/virtual/rc/rc0/input6 [ 4.054614] IR RC6 protocol handler initialized [ 4.054787] rc0: ITE8708 CIR transceiver as /devices/virtual/rc/rc0 [ 4.054839] ite_cir: driver has been successfully loaded [ 4.057338] IR JVC protocol handler initialized [ 4.061553] IR Sony protocol handler initialized [ 4.066578] input: MCE IR Keyboard/Mouse (ite-cir) as /devices/virtual/input/input7 [ 4.066724] IR MCE Keyboard/mouse protocol handler initialized [ 4.072580] lirc_dev: IR Remote Control driver registered, major 250 [ 4.073280] rc rc0: lirc_dev: driver ir-lirc-codec (ite-cir) registered at minor = 0 [ 4.073286] IR LIRC bridge handler initialized [ 4.077849] Linux video capture interface: v2.00 [ 4.079402] uvcvideo: Found UVC 1.00 device Laptop_Integrated_Webcam_2M (0c45:640f) [ 4.085492] EDAC MC: Ver: 2.1.0 [ 4.087138] lib80211_crypt: registered algorithm 'TKIP' [ 4.091027] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8 [ 4.091733] snd_hda_intel 0000:02:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 4.091826] snd_hda_intel 0000:02:00.1: irq 47 for MSI/MSI-X [ 4.091861] snd_hda_intel 0000:02:00.1: setting latency timer to 64 [ 4.093115] EDAC i7core: Device not found: dev 00.0 PCI ID 8086:2c50 [ 4.112448] HDMI status: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0 [ 4.112612] input: HD-Audio Generic HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/0000:02:00.1/sound/card1/input9 [ 4.113311] type=1400 audit(1342032325.540:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=658 comm="apparmor_parser" [ 4.114501] type=1400 audit(1342032325.540:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=658 comm="apparmor_parser" [ 4.115253] type=1400 audit(1342032325.540:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=658 comm="apparmor_parser" [ 4.121870] input: Laptop_Integrated_Webcam_2M as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.4/1-1.4:1.0/input/input10 [ 4.122096] usbcore: registered new interface driver uvcvideo [ 4.122100] USB Video Class driver (1.1.1) [ 4.128729] [fglrx] Maximum main memory to use for locked dma buffers: 5840 MBytes. [ 4.129678] [fglrx] vendor: 1002 device: 68c0 count: 1 [ 4.131991] [fglrx] ioport: bar 4, base 0x2000, size: 0x100 [ 4.132015] pci 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 4.132024] pci 0000:02:00.0: setting latency timer to 64 [ 4.133712] [fglrx] Kernel PAT support is enabled [ 4.133747] [fglrx] module loaded - fglrx 8.96.4 [Mar 12 2012] with 1 minors [ 4.162666] eth1: Broadcom BCM4727 802.11 Hybrid Wireless Controller 5.100.82.38 [ 4.184133] device-mapper: multipath: version 1.3.0 loaded [ 4.196660] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [ 4.279897] input: Dell WMI hotkeys as /devices/virtual/input/input11 [ 4.292402] Bluetooth: Core ver 2.16 [ 4.292449] NET: Registered protocol family 31 [ 4.292454] Bluetooth: HCI device and connection manager initialized [ 4.292459] Bluetooth: HCI socket layer initialized [ 4.292463] Bluetooth: L2CAP socket layer initialized [ 4.292473] Bluetooth: SCO socket layer initialized [ 4.296333] Bluetooth: RFCOMM TTY layer initialized [ 4.296342] Bluetooth: RFCOMM socket layer initialized [ 4.296345] Bluetooth: RFCOMM ver 1.11 [ 4.313586] ppdev: user-space parallel port driver [ 4.316619] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 4.316625] Bluetooth: BNEP filters: protocol multicast [ 4.383980] type=1400 audit(1342032325.812:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=938 comm="apparmor_parser" [ 4.385173] type=1400 audit(1342032325.812:6): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=938 comm="apparmor_parser" [ 4.425757] init: failsafe main process (898) killed by TERM signal [ 4.477052] type=1400 audit(1342032325.904:7): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1011 comm="apparmor_parser" [ 4.477592] type=1400 audit(1342032325.904:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=1010 comm="apparmor_parser" [ 4.478099] type=1400 audit(1342032325.904:9): apparmor="STATUS" operation="profile_load" name="/usr/sbin/tcpdump" pid=1017 comm="apparmor_parser" [ 4.479233] type=1400 audit(1342032325.904:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1014 comm="apparmor_parser" [ 4.510060] vesafb: mode is 1152x864x32, linelength=4608, pages=0 [ 4.510065] vesafb: scrolling: redraw [ 4.510071] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 [ 4.510084] mtrr: no more MTRRs available [ 4.513081] vesafb: framebuffer at 0xd0000000, mapped to 0xf9400000, using 3904k, total 3904k [ 4.515203] Console: switching to colour frame buffer device 144x54 [ 4.515278] fb0: VESA VGA frame buffer device [ 4.590743] tg3 0000:0b:00.0: irq 48 for MSI/MSI-X [ 4.702009] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 4.704409] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 4.978379] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000 [ 5.030104] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input12 [ 5.045782] kvm: VM_EXIT_LOAD_IA32_PERF_GLOBAL_CTRL does not work properly. Using workaround [ 5.519573] [fglrx] ATIF platform detected with notification ID: 0x81 [ 6.391466] fglrx_pci 0000:02:00.0: irq 49 for MSI/MSI-X [ 6.393137] [fglrx] Firegl kernel thread PID: 1305 [ 6.393306] [fglrx] Firegl kernel thread PID: 1306 [ 6.393472] [fglrx] Firegl kernel thread PID: 1307 [ 6.393726] [fglrx] IRQ 49 Enabled [ 6.528052] postgres (1308): /proc/1308/oom_adj is deprecated, please use /proc/1308/oom_score_adj instead. [ 6.532080] [fglrx] Gart USWC size:1280 M. [ 6.532084] [fglrx] Gart cacheable size:508 M. [ 6.532091] [fglrx] Reserved FB block: Shared offset:0, size:1000000 [ 6.532094] [fglrx] Reserved FB block: Unshared offset:f8fd000, size:403000 [ 6.532098] [fglrx] Reserved FB block: Unshared offset:3fff4000, size:c000 [ 17.423743] eth1: no IPv6 routers present [ 75.836426] warning: `proftpd' uses 32-bit capabilities (legacy support in use) [ 75.884215] init: plymouth-stop pre-start process (2922) terminated with status 1 [ 543.679614] eth1: no IPv6 routers present lsmod Module Size Used by kvm_intel 127560 0 kvm 359456 1 kvm_intel joydev 17393 0 vesafb 13516 1 parport_pc 32114 0 bnep 17830 2 ppdev 12849 0 rfcomm 38139 0 bluetooth 158438 10 bnep,rfcomm dell_wmi 12601 0 sparse_keymap 13658 1 dell_wmi binfmt_misc 17292 1 dell_laptop 17767 0 dcdbas 14098 1 dell_laptop dm_multipath 22710 0 fglrx 2909855 143 snd_hda_codec_hdmi 31775 1 psmouse 72919 0 serio_raw 13027 0 i7core_edac 23382 0 lib80211_crypt_tkip 17275 0 edac_core 46858 1 i7core_edac uvcvideo 67203 0 snd_hda_codec_idt 60251 1 videodev 86588 1 uvcvideo ir_lirc_codec 12739 0 lirc_dev 18700 1 ir_lirc_codec ir_mce_kbd_decoder 12681 0 snd_seq_midi 13132 0 ir_sony_decoder 12462 0 ir_jvc_decoder 12459 0 snd_rawmidi 25424 1 snd_seq_midi ir_rc6_decoder 12459 0 wl 2646601 0 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event ir_rc5_decoder 12459 0 video 19068 0 snd_hda_intel 32765 5 snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq snd_hda_codec 109562 3 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_hda_intel rc_rc6_mce 12454 0 lib80211 14040 2 lib80211_crypt_tkip,wl snd_hwdep 13276 1 snd_hda_codec ir_nec_decoder 12459 0 snd_pcm 80845 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec ite_cir 24743 0 rc_core 21263 10 ir_lirc_codec,ir_mce_kbd_decoder,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_rc5_decoder,rc_rc6_mce,ir_nec_decoder,ite_cir snd_timer 28931 2 snd_seq,snd_pcm wmi 18744 1 dell_wmi snd 62064 20 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_rawmidi,snd_seq,snd_seq_device,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_timer mac_hid 13077 0 soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm coretemp 13269 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp tg3 141369 0 firewire_ohci 40172 0 sdhci_pci 18324 0 firewire_core 56906 1 firewire_ohci sdhci 28241 1 sdhci_pci crc_itu_t 12627 1 firewire_core lshw *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 logical name: eth1 version: 01 serial: 70:f1:a1:a9:54:31 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 ip=192.168.0.117 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0900000-f0903fff *-network description: Ethernet interface product: NetLink BCM5784M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:0b:00.0 logical name: eth0 version: 10 serial: b8:ac:6f:71:02:a6 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 firmware=sb v2.19 latency=0 link=no multicast=yes port=twisted pair resources: irq:48 memory:f0d00000-f0d0ffff

  Read the article

• wireless detected but Can't connect to network, Wifi card intel pro wireless N100 BGN

  - by Alexandre777

  Thanks in advance, I installed Linux Mint kernel 3.0.0-12 x64 ,wireless is detected and I configure it in network manager but can't coonect, there are the results of command line: $ iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off $ sudo lshw -C network** *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 00:1e:64:51:c9:d6 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-12-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:48 memory:d7400000-d7401fff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: c0 serial: 48:5b:39:99:8f:16 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.2 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:51 memory:d3800000-d383ffff ioport:8000(size=128 $ rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Thank you.

  Read the article

• SQLAuthority News – Amazon Gift Card Raffle for Beta Tester Feedback for NuoDB

  - by pinaldave

  As regular readers know I’ve been spending some time working with the NuoDB beta software. They contacted me last week and asked if I would give you a chance to try their new web-based console for their scalable, SQL-compliant database. They have just put out their final beta release, Beta 9.  It contains a preview of a new web-based “NuoConsole” that will replace and extend the functionality of their current desktop version.  I haven’t spent any time with the new console yet but a really quick look tells me it should make it easier to do deeper monitoring than the older one. It also looks like they have added query-level reporting through the console. I will try to play with it soon. NuoDB is doing a last, big push to get some more feedback from developers before they release their 1.0 product sometime in the next several weeks. Since the console is new, they are especially interested in some quick feedback on it before general availability. For SQLAuthority readers only, NuoDB will raffle off three $50 Amazon gift cards in exchange for your feedback on the NuoConsole preview. Here’s how to Enter Download NuoDBeta 9 here You must build a domain before you can start the console. Launch the Web Console. Windows Code: start java -jar jarnuodbwebconsole.jar Mac, Linux, Solaris, Unix Code: java -jar jar/nuodbwebconsole.jar Access the Web Console: Code: http://localhost:8080 When you have tried it out, go to a short (8 question) survey to enter the raffle Click here for the survey You must complete the survey before midnight EDT on October 17, 2012. Here’s what else they are saying about this last beta before general availability: Beta 9 now supports the Zend PHP framework so that PHP developers can directly integrate web applications with NuoDB. Multi-threaded HDFS support – NuoDB Storage Managers can now be configured to persist data to the high performance Hadoop distributed file system (HDFS). Beta 9 optimizes for multi-thread I/O streams at maximum performance. This enhancement allows users to make Hadoop their core storage with no extra effort which is a pretty cool idea. Improved Performance –On a single transaction node, Beta 9 offers performance comparable with MySQL and MariaDB. As additional nodes are added, NuoDB performance improves significantly at near linear scale. Query & Explain Plan Logging – Beta 9 introduces SQL explain plans for your queries. Qualify queries with the word “EXPLAIN” and NuoDB will respond with the details of the execution plan allowing performance optimization to SQL. Through the NuoConsole, you can now kill hung or long running queries. Java App Server Support – Beta 9 now supports leading Web JEE app servers including JBoss, Tomcat, and ColdFusion. They’ve also reported: Improved PHP/PDO drivers Support for Drupal Faster Ruby on Rails driver The Hibernate Dialect supports version 4.1 And good news for my readers: numerous SQL enhancements They will share the results of the web console feedback with me.  I’ll let you know how it goes. Also the winner of their last contest was Jaime Martínez Lafargue!  Do leave a comment here once you complete the survey.  Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: SQL Authority Tagged: NuoDB

  Read the article

• Ethernet card not detected on Ubuntu Server 12.04

  - by Dana

  My onboard ethernet isn't detected after a re-install of Server 12.04. For reasons I won't get into here, I had to put the server's drive into another machine to install Ubuntu, then swap back into the server. So the server starts up fine, except for the "Waiting for network configuration". I read in another article that Server, by default, doesn't handle new mac addresses for hardware changes dynamically, unlike Ubuntu Desktop, but a look at /etc/udev/rules.d/70-persistent-net.rules shows only one ethernet interface. Shouldn't it show both the old, and the new? lspci -vv shows an ethernet interface, so what the heck is going on? I should mention that the onboard LAN is enabled in the BIOS. And I know this isn't important, but all this started when I changed some network configuration settings in webmin before the re-install. It couldn't download any updates, so I tinkered a little. Broke, it, installed FreeNAS, which worked, but I didn't like it, then went back to Ubuntu Server, and now I'm in this pickle. Thanks for any advice!

  Read the article

• How to get Broadcom BCM 43XX Wireless card working

  - by Fer1805

  NOTE - Although this question is for a specific version of Ubuntu and a specific Broadcom model, the answer to it is for most Broadcom models and versions of Ubuntu 11.04, 11.10, 12.04 and 12.10. If you have come here from another question, feel free to read the answer instead. The answer covers many problems with several solutions. I'm having serious problems installing the Broadcom drivers for Ubuntu 11.04. It worked perfectly on my previous version, but now, it is impossible. I'm a user with no advance knowledge in Linux, so I would need clear explanations on make, compile, etc. I was following the instructions on the following blog, with no luck. How can I get Broadcom BCM4311 Wireless working? Can someone help me? Edit: For the command: "lspci | grep Network", I get the following message: 06:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) For the command: iwconfig, i get the following: lo no wireless extensions. eth0 no wireless extensions. When i follow the following steps (from the above link), there are a NO error message at all: open the 'Synaptic Package Manager' and search for bcm uninstall the bcm-kernel-source package make sure that the firmware-b43-installer and the b43-fwcutter packages are installed type into terminal: cat /etc/modprobe.d/* | egrep '8180|acx|at76|ath|b43|bcm|CX|eth|ipw|irmware|isl|lbtf|orinoco|ndiswrapper|NPE|p54|prism|rtl|rt2|rt3|rt6|rt7|witch|wl' (you may want to copy this) and see if the term blacklist bcm43xx is there if it is, type cd /etc/modprobe.d/ and then sudo gedit blacklist.conf put a # in front of the line: blacklist bcm43xx then save the file (I was getting error messages in the terminal about not being able to save, but it actually did save properly). reboot 'End of procedure' Before (not ubuntu 11.04), if i wanted to connect wireles, i just went to the icon at the upper side of the screen, click, showed ALL the wireless network available, and done. Now, the only options i see are: Wired Network Auto Eth0 Disconnect VPN Enable networking Connection information Edit connection. hope above info is enough for your help.

  Read the article

• Graphic Card Installation Failure (NV 9600M GT)

  - by Georg

  I wanted to switch from 7 to Ubuntu. Now, the first thing that holds me back is the installation of the driver for my Nvidia 9600M GT. Ubuntu recommends me 4 drivers from the "Additional Driver" Section. Now, whatever driver I install, there are four things happening RANDOMLY after rebooting: The pc freezes before seeing bootup splash The pc freezes while seeing bootup splash image (ubuntu logo with the 5 dots) The pc gets into login screen and freezes instantly (Thought the unity-bar is transparent now) The pc freezes right after beeing able to login. (While this is happening the unity-bar changes from transparent to ugly-flat-style) I also tried to install the official Nvidia .run file but after exiting the X-Server, it says the driver is not compatible with the kernel and exits installation. Can somebody help me? I really wanna get rid of Windows :( But Ubuntu drives me perfectly insane. Please answer as noobish as possible. I'm an expert Windows user, but Linux is absolutely new to me. My Specs: Ubuntu 11.10 installed from USB Stick (like 100 times now :/ because I dont know how to remove the driver in recovery mode) 9600M GT 4GB Ram Intel Centrino 2 Dual Core 2.26GHz Win 7 and Ubuntu running along side. Thank you in advance, regards.

  Read the article

• lubuntu - Sound card detected but no sound

  - by CookieMonster

  I installed Lubuntu 12.10 on my old laptop (Sharp Mebius PC-MR80J), but sound does not work. Here are things I tried. aplay -l does not output anything. When I run alsamixer, I see only one bar that says "Beep". I installed pavucontrol, pulseaudio, pulseaudio-utils and libgtk-3-0 and checked output devices, but I only see "Dummy ouput" and there is no hardware output devices. cat /proc/asound/cards returns the following. 0 [Intel ]: HDA-Intel - HDA Intel HDA Intel at 0xfeb38000 irq 40 cat /proc/asound/devices outputs the following. 1: : sequencer 2: [ 0- 1]: hardware dependent 3: [ 0- 0]: hardware dependent 4: [ 0] : control 33: : timer The laptop was running Windows XP before and sound (both input and outpu) was working. What can I do now?

  Read the article

• installing my Graphic Card on ubuntu12.04

  - by lamouchi amine

  I have a HP Pavillion G6 series 1225, i5 laptop with Radeon HD 6470M switchable VGA. i installed Ubuntu 12.04 LTS but the VGA drivers don't work properly. I want to install drivers into the Ubuntu. But when I do it arrived error message like this: sorry, installation of this driver failed. Please have a look at the log file for details: /var/log/jockey.log I found a solution in a link: http://ubuntuforums.org/showthread.php?t=1930450 It works for a few steps and then in the installation of the package of the AMD driver, a message pops up 'fatal error' and it redirects me to Ask Ubuntu to find a solution, please help me, I need to make it work.

  Read the article

• Restart problem after installing graphical card driver

  - by Tim

  My laptop is Lenovo T400, running Ubuntu 10.10. My problem: I just run jockey-gtk and installed ATI/AMD proprietary FGLRX graphics driver. But after reboot, there is a short period of graphical "Ubuntu" and then instead of starting X-window it completely changed to command line to ask me to login. Even after login and then issuing xinit, it still failed to start X. To solve this problem: I followed this post, where one person suggested to you can simply write sudo apt-get remove fglrx This worked for me. If it doesn't work, then try sudo apt-get remove xorg-driver-fglrx and restart. I actually don't need the driver anyway, so I issued the first command after login under command line. But after reboot, the situation is even worse, and there is now even no command-line interface to ask me login, instead the screen is completely blank with just some ambient light in the background and Ubuntu is hanging there probably forever. So I have no chance to try the second command the person suggested. I was wondering what I can do now to solve my problem? Thanks and regards!

  Read the article

• HDMI audio output problems with Radeon card

  - by Matt Robinson

  No matter how much advice I follow, I still cannot get any audio to come out through my HDMI connection. I've tried downloading the latest proprietary FGLRX graphics drivers, and I've also gone into /etc/default/grub and altered GRUB_CMDLINE_LINUX_DEFAULT="quiet splash" into this GRUB_CMDLINE_LINUX_DEFAULT="quiet splash radeon.audio=1" But still I cannot get any sound nor can I get HDMI sound output to show up in Sound Settings or Pulse Audio Volume Control. I can get video to show up just fine on my monitor through HDMI so I'm sure this problem is fixable! I know this is an old problem with Ubuntu, but any new strategies into the problem would be much appreciated. With that being said, here are some of my specs: Ubuntu 12.04 LTS AMD Radeon HD 7520G

  Read the article

• Taking advantage of an "Intel Turbo Memory" card for swap or fast bootup

  - by Brian Ballsun-Stanton

  I have an X61 thinkpad (currently running 10.10) that I purchased 3 years ago. I splurged a little and got a Turbo Memory expansion to improve my windows boots. When I installed 10.04 (and subsquently upgraded to 10.10) there was no Turbo Memory support and there's an awful lot of noise on searches. 1) Is there any support for Intel Turbo Memory in 11.04 or trivially compilable into the kernel as swap, suspend, hibernate point, or boot partition? 2) If there is, should I bother trying to use it?

  Read the article

• fix pavucontrol Alsa mixer with creative card

  - by schwiz

  I have been desperately trying to get my creative x-fi soundcard to work with my 10.10 install and I am almost there! I have 1 speaker working and when I open volume control I see that my device is Creative X-fi (Also mixer). However, it appears to be stuck on mono. When I open pavucontrol I get a message that says Connection failed: Connection refused and it exits. Before it closes I can see that playback is set to mono but it won't let me change before it closes. Can someone help me over this last hump? I am running 32 bit 10.10 any advice is much appreciated.

  Read the article

• Disable ATI Radeon graphics card and use intel graphics (switcheroo unavailable)

  - by user92356

  So I have a HP Envy with ATI Radeon 5450 + intel switchable graphics. I think (though I'm not sure) that the Radeon is running right now on Ubuntu 12.04 (because my laptop is making too much noise when I'm doing something non gpu intensive like word processing, or web browsing). So what I want to do is disable the ATI Radeon and use the Intel instead. I looked around and it seems all the solutions use switcheroo, but I dont have it on my computer! I think this happened because I tried installing the proprietary driver (fglrx). Any and all help is 200% appreciated, thank you

  Read the article

• ATI graphics card, with gnome shell on Ubuntu 11.10, screen flickers

  - by bioShark

  After installing gnome shell, without any problem, after log in the fonts are missing and it looks like crap...nothing is readable. Don't want to make it a double post, because my issue is similar to the one from this question but for me the problems have not been solved properly. After running the commands from that post, and installing the latest AMD 11.10 driver, the Gnome shell display issues have been solved. But each time I move the mouse in the upper left corner, to bring up the applications...my entire screen flickers. Without the applications been displayed, everything looks fine. Hardware: ATI HD4870, Intel Q6600.

  Read the article

• Compiz with Intel video card not working after upgrade to 11.04

  - by fazi

  After upgrade to ubuntu 11.04 from 10.10 My compiz stop working I have no cube effects and preview files and other compiz stuff. I have intel x4500 (00:02.1 Display controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03) ) glxinfo name of display: :0 display: :0 screen: 0 direct rendering: Yes server glx vendor string: Brian Paul server glx version string: 1.4 Mesa 7.11-devel I have removed compiz, gnome (witch --purge) and install again, nothing works :( Im using default ubuntu desktop (no unity) any idea how can I fix this?:

  Read the article

• Split screen and other issues on Ubuntu 11.10 with ATI graphics card

  - by garus

  Ever since updating my Ubuntu 11.04 to 11.10 I experience issues with graphics. The biggest is the "split screen" effect where my desktop is shifted to the right, resulting in having Unity bar in the middle of the screen. As shown here: http://i.imgur.com/I8nmZ.jpg This changes from boot to boot, sometimes it's on the left, sometimes in the middle. What I tried: Removing fglrx drivers completely Installing post-update version of them, but installation is broken ATM in the Ubuntu, so no go. No one is even trying to fix it (bug report https://bugs.launchpad.net/ubuntu/+source/nvidia-common/+bug/873058 and a couple of duplicates out there) Also using the open source "radeon" driver results in the same (I have a better successful boot ratio with this one, proprietary rarely lets me boot) Other artifacts are: serious screen tearing weird lines flickering in random places lagginess Did anyone experience that? My specs: Ubuntu 11.10 AMD Radeon HD 6950 1GB

  Read the article

• Why doesn't my graphic card support 1280*1024?

  - by Allwar

  Hi, I have an external monitor which is an 20" 1280*1024. In windows 7 it works fine with that resolution but in ubuntu it can't. Example: In windows I connect it and activates it, done. In ubuntu I connect and the only resolution that is available is the ones my laptop screen support, 12" 1366*768. My laptop is an asus 1201n. If I force it to use 1280*1024 both screen crashes and i have to force a reboot. what should I do? alvar@alvars-laptop:~$ disper -l display DFP-0: HSD121PHW1 resolutions: 320x175, 320x200, 360x200, 320x240, 400x300, 416x312, 512x384, 640x350, 576x432, 640x400, 680x384, 720x400, 640x480, 720x450, 640x512, 700x525, 800x512, 840x525, 800x600, 960x540, 832x624, 1024x768, 1366x768 display CRT-0: CRT-0 resolutions: 320x240, 400x300, 512x384, 680x384, 640x480, 800x600, 1024x768, 1152x864, 1360x768

  Read the article

• ubuntu nic card issue

  - by Blainer

  I am trying to install NIC r8168 and it shows everything installed ok. It is a brand new NIC and the lights wont come on when I plug in a ethernet. The NIC is that is not working is eth0. Why does it show the r8168 driver being used by 0? My NIC model number is ST1000SPEX if anyone is wondering. lsmod Module Size Used by r8168 215669 0 ifconfig eth0 Link encap:Ethernet HWaddr 00:0a:cd:1e:0a:4a UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:43 Base address:0x2000 eth1 Link encap:Ethernet HWaddr 00:19:d1:1d:f6:7a inet addr:192.168.1.83 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::219:d1ff:fe1d:f67a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:551467 errors:0 dropped:0 overruns:0 frame:0 TX packets:145219 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:409744342 (409.7 MB) TX bytes:12233173 (12.2 MB) Interrupt:21 Memory:dfde0000-dfe00000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:280 errors:0 dropped:0 overruns:0 frame:0 TX packets:280 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:22608 (22.6 KB) TX bytes:22608 (22.6 KB) Ubuntu 11.10 x64 Kernel 3.0.0-12-generic

  Read the article

• ATI graphics card, with gnome shell, screen flickers

  - by bioShark

  After installing gnome shell, without any problem, after log in the fonts are missing and it looks like crap...nothing is readable. Don't want to make it a double post, because my issue is similar to the one from this question but for me the problems have not been solved properly. After running the commands from that post, and installing the latest AMD 11.10 driver, the Gnome shell display issues have been solved. But each time I move the mouse in the upper left corner, to bring up the applications...my entire screen flickers. Without the applications been displayed, everything looks fine. Hardware: ATI HD4870, Intel Q6600.

  Read the article

• Development of a Card Game Website [on hold]

  - by Correna Hurley

  Yahoo did away with all of their "parlor-type" games on 3/31/14. There is a great demand to get these games back, but Yahoo has no plan to do so. I'd like to find someone who has the knowledge necessary to create such an "animal" and would be willing to give it a try. If someone from this forum would be so kind as to point me in the right direction to find such an individual, I'd be grateful. Thank you.

  Read the article

• Phishing Scam Targets Apple Gift Card Holders

  Online scamsters are using Apple's brand as a lure to get people to divulge their personal information and plunder their gift cards.

  Read the article

• How to reset wireless card settings

  - by Nissan911

  Yesterday i was playing around of the wireless settings, and set up a tftp server. Today, i found the wireless icon does not show up on the panel anymore.. monitor and bluetooth are still there... I did: ifconfig -a, and it shows: etho0 link encap:ethernet, and it has: HWaddress inet6 addresss. RXbytes 0 TX bytes: 0, but it does not even have a ip4 address, nor a mask. The other one is: l0 link encap: local loopback inet addr 127.0.0.1. mask 2550 0 0 Can anyone help me how to reset the settings for my wireless connection? Thanks

  Read the article

• AR242x / AR542x wireless card not working

  - by Pipan87

  My wifi worked perfect until I updated to the latest version of Ubuntu. Now I don't find any wireless connections at all. I have tried lots of guides on the internet but I can't get it to work. I did however start to work once after writing something I don't remember in Terminal, but after rebooting it stopped working again. Some info (don't know if you need more to help): 01:00.0 Ethernet controller: Atheros Communications AR8121/AR8113/AR8114 Gigabit or Fast Ethernet (rev b0) Subsystem: Acer Incorporated [ALI] Device 022c Flags: bus master, fast devsel, latency 0, IRQ 44 Memory at 55200000 (64-bit, non-prefetchable) [size=256K] I/O ports at 3000 [size=128] Capabilities: [40] Power Management version 2 Capabilities: [48] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [58] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [180] Device Serial Number ff-93-2e-de-00-23-8b-ff Kernel driver in use: ATL1E Kernel modules: atl1e 02:00.0 Ethernet controller: Atheros Communications Inc. AR242x / AR542x Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: Foxconn International, Inc. Device e00d Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at 54100000 (64-bit, non-prefetchable) [size=64K] Capabilities: [40] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [60] Express Legacy Endpoint, MSI 00 Capabilities: [90] MSI-X: Enable- Count=1 Masked- Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel Kernel driver in use: ath5k Kernel modules: ath5k

  Read the article

< Previous Page | 20 21 22 23 24 25 26 27 28 29 30 31  | Next Page >