Search Results

Search found 13900 results on 556 pages for 'physical drive'.

Page 241/556 | < Previous Page | 237 238 239 240 241 242 243 244 245 246 247 248  | Next Page >

• Disk I/O error copying a Exchange 2007 database

  - by Scottio

  Hi all, A short time ago due to disk space I moved our Exchange database onto an external drive, the drive was new and the database was being backed up daily. I've now discovered the database is corrupt, I've run the Exchange utils to fix the database and this works but it corrupts again as soon as I try to move it. I need to get it off the disk, any suggestions? I'm also trying to restore the last good database but I'd like try to get the database off this disk, any suggestions? PS I know putting the db on an external disk was a bad move, I had no where else to put it :-( Thanks

  Read the article

• Configuring RAID1 on HP Proliant Microserver N54L / Ubuntu 14.04.1 LTS [duplicate]

  - by Chris Beach

  This question already has an answer here: Cant find my harddrives in ubuntu installation? 2 answers I've bought a N54L and fitted two 3GB drives. Keen to get set up with RAID1. BIOS: SATA controller mode set to "RAID" RAID Option ROM utility: both physical drives set up as one logical drive When I came to install Ubuntu (14.04.1), both drives appeared during the setup process. I was only expecting to see the logical drive, although I'm a complete novice with RAID. I've read that the HP Proliant Microservers don't have "proper" RAID support, and require some kind of driver to be installed. I've tried a few HP utilities from the following apt repo: deb http://downloads.linux.hp.com/SDR/repo/mcp wheezy/current non-free On installation, most say "server not supported" Would appreciate your advice.

  Read the article

• HP Recovery options: System Recovery not showing

  - by sha404

  I am using HP Pavilion dv4 notebook. Previously, there were following options in Recovery Manager(using f11 during boot): +System Recovery +Factory Restore +Minimized Image Recovery The System Recovery option allows me to restore only Operating system drive e.g. C:\ drive, keeping all other user (me) created hard drives intact. I made a set of recovery disk. Since then I don't see the System Recovery option in HP Recovery Manager. But all other options are still there. But when I use recovery disks that i created earlier, that option e.g. System Recovery is shown. But It's really boring and time consuming to use disks for recovery. So, what's the problem with internal HP Recovery Manager? Why isn't it showing that option?

  Read the article

• HP D2D 4312 Bacula configuration

  - by krisdigitx

  I have configured 5 libraries on the HP D2D system Discovery on the Bacula server shows only the last library and not all libraries. Why? [root@server bacula]# iscsiadm --mode discovery --type sendtargets --portal 10.66.59.114 10.66.59.114:3260,1 iqn.1986-03.com.hp:storage.d2dbs.czj2020vvy.50014380075dca5e.library12.drive1 10.66.59.114:3260,1 iqn.1986-03.com.hp:storage.d2dbs.czj2020vvy.50014380075dcaf2.library12.robotics I can query it fine using... [root@server bacula]# mtx -f /dev/sg2 inquiry Product Type: Tape Drive Vendor ID: 'HP ' Product ID: 'Ultrium 5-SCSI ' Revision: 'ED51' Attached Changer API: No [root@bray bacula]# mtx -f /dev/sg3 inquiry Product Type: Medium Changer Vendor ID: 'HP ' Product ID: 'MSL G3 Series ' Revision: 'EL41' Attached Changer API: No [root@server bacula]# mtx -f /dev/sg3 status Storage Changer /dev/sg3:1 Drives, 97 Slots ( 1 Import/Export ) Data Transfer Element 0:Empty Storage Element 1:Full :VolumeTag=50507F82 Storage Element 2:Full :VolumeTag=50507F83 Storage Element 3:Full :VolumeTag=50507F84 Storage Element 4:Full :VolumeTag=50507F85 Storage Element 5:Full :VolumeTag=50507F86 Storage Element 6:Full :VolumeTag=50507F87 Storage Element 7:Full :VolumeTag=50507F88 Does anyone have any good documentation for implementing Bacula with an HP D2D tape drive for server backups, and how to allocate libraries?

  Read the article

• Hyper-V Boot failure on VHD made with Acronis?

  - by gary

  hoping someone can advise on my problem, I am running Hyper-V core and trying to create my first VM for testing purposes. Using Acronis True Image echo server with UR I converted a Seerver 2000 tib to VHD. I then copied this across to the Hyper-V local drive and created a new VM pointing the hard drive to the vhd image. When I boot this up all I get is "Boot failure. Reboot and Select proper Boot device or Insert Boot media in selected Boot device". The original server had SCSI disks, the Hyper-V server doesn't, but I have ensured that it boots from an IDE disk and that it is in fact booting from that not the CD. I can only imagine this is caused by the SCSI disks on VHD but cannot for the life of me work out how to fix, I have several of these I need to do so starting to worry now! I can confirm that when I did this from tib to vmdk it worked first time using VMware on a laptop. Any help very much appreciated. Gary

  Read the article

• Supplementary Developer Laptop

  - by David Smith

  I'm looking to buy a laptop with the following specs for a developer. The goal will be to have a development machine supplementing the devs desktop. During work hours the dev will be on a beefy desktop. For working while on the go: trains, client sites, code camps, it would be nice to have a machine which can run Visual Studio 2008 without needing to remote desktop into their primary machine. What do you think is the lowest cost laptop meeting this need? Here are the specs I have in mind: SSD drive 64GB-doesn't need to be huge, most data is stored on servers. Will need to fit Windows 7, IIS, SQL Server, and Visual Studio 2010. RAM-3GB processor =Pentium Core 2 duo Screen size = 14 inches. OS doesn't matter. It will be paved with Windows 7 Ultimate optical drive omitted would be a plus. weight and battery life aren't so important because the machine will be plugged in almost all the time.

  Read the article

• Restoring Time Machine from two Macs onto one (new) mac

  - by Dan

  My parents used to have two Macs...a "iLamp-style" iMac for my Dad, and an iBook G4 for my Mom. A while back, I had setup the iMac to have an external Firewire Hard Drive for a Time Machine Volume, and backed up both the iMac and iBook to that drive. Recently, the iBook died and the iMac was really slow to work with. So my parents decided to replace the iBook with an iPad, and also purchased a Mac Mini. I need to help my parents get their data from their two computers (backed up by Time Machine) onto the same machine. Pretty much everything is identical between the two systems (same apps, etc), however, they both have individual email accounts and photos that they want to retain. Is it possible to do two Time Machine restores onto one computer?

  Read the article

• Simple bash scripting

  - by Richard Cotton

  I'm trying to get to grips with bash scripting via cygwin. My script is about as simple as it gets. I change the directory to the root of my C drive, and print the new location. #!/usr/bin/bash cd /cygdrive/c pwd is saved in the file chdir.sh in my home directory. I then call ./chdir.sh from the bash prompt. This results in the error : No such file or directorygdrive/c /cygdrive/c/Documents and Settings/rcotton I definitely have a C drive, and the command cd /cygdrive/c works when I call it directly from the bash prompt. I realise that this problem is likely stupidly simple; please can you tell me what I'm doing wrong.

  Read the article

• RAID 0 performance gains?

  - by NickAldwin

  I'm building a new computer over the summer. I'm fairly competent in computer hardware, and am thus building the computer from scratch. I have everything planned out, but I was wondering about RAID. I asked which RAID I should use earlier, but now that it's pretty clear that RAID 1 isn't really that great, I think I'll go with cloud-backup instead of disk-redundancy. However, I still face a choice: use two 1TB drives as two 1TB drives, or combine them into a RAID 0 striped array. Is there any performance gain at all? I know that if one drive dies, everything is gone, so is the performance gain worth it? I'm building a pretty advanced computer, with SLI video cards and a fast CPU, so I'm thinking RAID 0 would give me some good hard drive performance. From your experience, is RAID 0 viable?

  Read the article

• Windows could not update the computer's boot configuration.

  - by Luke Puplett

  Hello, I am trying to install Windows Web Server 2008 x64 (have tried 32-bit, too) onto an IBM eServer 326m and am getting the following error message some time after the unpacking files section: Windows could not update the computer's boot configuration. Installation cannot proceed. I can repair the boot information using the Repair option in the WinPE bit of the setup, and it reboots into the Windows installation, so it has good boot data on the drive. Just to complicate things, the server does not have a DVD-ROM so I'm installing from HDD to HDD, both SATA, one an SSD. I've tried each drive in isolation, e.g. removing the SSD and installing from spindle onto itself, same error every time. Flashed IBM BIOS, too. Thanks for your help. Luke

  Read the article

• Windows 7 Reading Proper Disk Usage Statistics on Mounted Volumes

  - by Troy Perkins

  I'm running windows 7 with 2 x 1.5 TBYTE Drives. The second internal drive is setup as a mounted volume as C:\Archives Clicking computer icon in windows explorer, it only shows capacity stats for C: and Not C:\Archives Also, the usage stats that do show for C: show to be 100% capacity red - yet the system runs fine. No warnings. Can someone explain this? I do have a lot of stuff on the c: drive, but I'm sure its not 1.5 TB worth and C:\Archives hardly has anything it. Thanks! Troy

  Read the article

• NST-475LX-BK NAS Enclosure Is It Any Good?

  - by peter

  Hi All, Has anyone got one of these NST-475LX-BK? It is this, Vantec NexStar LX Ultra Gigabit NAS Hard Drive Enclosure. http://www.vantecusa.com/front/product/view_detail/403#rev What are your experiences with it? What type of file system does it format the drive to? It has an eSata cable so it must support NTFS right? Or does it use ext3? How good is the media streaming? What type of files can it stream? MPEG 2? Thanks.

  Read the article

• Automate uploading of videos to YouTube

  - by John

  Here's the problem: I would like to keep lots of home made videos. Of course, they are subject to being lost, or somebody could steal the the computer, or water or fire could destroy them. Secondly, I have to plug in my hard drive every time I want to watch something, which I find slow and cumbersome. I was thinking that perhaps I could upload the videos to Youtube with the privacy set to invite only and then delete the video from the hard drive automatically. Could this be done?

  Read the article

• Fixing Windows 7 hibernation

  - by 80skeys

  I've been mucking around with the partitions on my laptop (I'm an experienced Linux/grub guy) and have somehow ended up affecting the ability of Windows 7 to go into hibernate mode. All other functionality seems to be okay. But when I press Hibernate, it behaves as if it starts to (screen goes dark, a little disk activity) but never powers off and if I move the mouse the login screen instantly comes up. I don't know if Window uses a separate partition for hibernation? There is a 200MB partition on the drive - I seem to recall it was related to diagnostics or some other Windows- boot menu stuff. In any case, wondering if there's some commands I can run to restore the ability to hibernate and also which partitions need to be marked "active" and if there's anything I need to do to the MBR of the hard drive or the MBR of the Windows partition? As I said, Windows boots fine as long as it is designated the Active partition. I just need to fix Hibernation.

  Read the article

• Measuring 'total bytes written' under Linux

  - by badnews

  We're quite interested in exploring the possibility of using SSD drives in a server environment. However, one thing that we need to establish is expected drive longevity. According to this article manufacturer's are reporting drive endurance in terms of 'total bytes written' (TBW). E.g. from that article a Crucial C400 SSD is rated at 72TB TBW. Do any scripts/tools exist under the Linux ecosystem to help us measure TBW? (and then make a more educated decision on the feasibility of using SSD drives)

  Read the article

• broadcom 5722 NIC not installed on Ubuntu Server, although driver present

  - by Bastien

  Hello, I just installed Ubuntu Server 10.04 LTS, running kernel 2.6.32-24-server, on a brand new Dell T110 server, supposedly fully compatible with Ubuntu Server. I have two NICs: one ONBOARD, the other additional on PCI. both of them are Broadcom netXtreme 5572. on the first boot of the system, I could see both cards as eth0 and eth1 (with ifconfig) I configured eth0 as static IP (as planned), and did not configure eth1. after rebooting, one of the two NICs "disappeared": it does not appear in ifconfig at all. the one that disappeared is the ONBOARD one. I investigated a bit and found the following things: the card is SEEN, but not "installed", it appears as "UNCLAIMED" in lshw: *-network UNCLAIMED description: Ethernet controller product: NetXtreme BCM5722 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress cap_list configuration: latency=0 resources: memory:df9f0000-df9fffff *-network description: Ethernet interface product: NetXtreme BCM5722 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 00 serial: 00:10:18:60:23:64 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.102 duplex=full firmware=5722-v3.09 ip=10.129.167.25 latency=0 link=yes multicast=yes port=twisted pair speed=100MB/s resources: irq:35 memory:dfaf0000-dfafffff so I checked my dmesg and found a few strange lines, showing, there actually is a problem bringing up this card: [ 3.737506] tg3: Could not obtain valid ethernet address, aborting. [ 3.737527] tg3 0000:04:00.0: PCI INT A disabled [ 3.737535] tg3: probe of 0000:04:00.0 failed with error -22 [ 3.737553] alloc irq_desc for 17 on node -1 [ 3.737555] alloc kstat_irqs on node -1 [ 3.737560] tg3 0000:05:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 3.737566] tg3 0000:05:00.0: setting latency timer to 64 [ 3.793529] eth0: Tigon3 [partno(BCM95722A2202G) rev a200] (PCI Express) MAC address 00:10:18:60:23:64 [ 3.793532] eth0: attached PHY is 5722/5756 (10/100/1000Base-T Ethernet) (WireSpeed[1]) [ 3.793534] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1] [ 3.793536] eth0: dma_rwctrl[76180000] dma_mask[64-bit] that actually shows that one NIC is recognized, the other is not. I researched a bit more, with lspci -v: 04:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Subsystem: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Flags: fast devsel, IRQ 16 Memory at df9f0000 (64-bit, non-prefetchable) [size=64K] Capabilities: [48] Power Management version 3 Capabilities: [50] Vital Product Data <?> Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number 00-00-00-fe-ff-00-00-00 Kernel modules: tg3 05:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Subsystem: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Flags: bus master, fast devsel, latency 0, IRQ 35 Memory at dfaf0000 (64-bit, non-prefetchable) [size=64K] Expansion ROM at <ignored> [disabled] Capabilities: [48] Power Management version 3 Capabilities: [50] Vital Product Data <?> Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+ Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number 64-23-60-fe-ff-18-10-00 Capabilities: [16c] Power Budgeting <?> Kernel driver in use: tg3 Kernel modules: tg3 here I could see that the MAC address is 00-00-00-FE-FF-00-00-00, which, according to some forum posts on several websites, could be an issue. I've researched everything I could on the net, and found out several people having slightly comparable issues, but they usually involve different HW, and do not provide a proper explanation / solution... I would appreciate if anyone around here has some info to share ! thanks

  Read the article

• Exchange 2007 CCR: Logs not replicating to passive node partition

  - by yum_tacos4u

  In my environment I have setup Exchange 2007 in an CCR cluster, mirroring our main servers to a set of servers in passive mode. One of the partitions on the passive node that I have setup for the logs for Exchange 2007 has faulted, causing the partition to be unreadable. I have replaced the partition on the passive node, and setup the drive to mirror the one in active mode, but the logs are not replicating since the change. Is there anyway to force the replication of the new drive for the logs to the new partition? Any idea why the logs are not replicating? Any help or comments is appreciated, and thanks in advance.

  Read the article

• Find or restore wiki pages. (Computer will not boot anymore and need the wiki pages)

  - by Nathan187

  A few years ago, where I work, I created a wiki for me and my co-workers. We work on a lot of old programs and to help with cross training, we put a lot of our notes in the wiki. Sadly, the wiki was hosted on my machine and my machine has died. I can pull the drive out and hook it up to an enclosure and still see the files, etc. I want to know...is there a way to get the files/pages from that wiki somehow. I think they are stored in a mysql database somewhere. Yeah it sucks and I had a lot of stuff on that drive but the most important thing for me now is to get those notes (wiki pages). Any help would be appreciated.

  Read the article

• Read Linux-formatted (ext3) EBS volume mounted on Windows Server 2008 instance

  - by Greg Owen

  I've got a Windows Server 2008 R2 instance set up in Amazon EC2. I've also got some Ubuntu instances on the same EC2 account. I'd like to be able to mount the EBS volume from one of the Ubuntu instances onto the Windows instance as an external drive and then access that drive from the Windows instance. I've looked at tools like ext2fsd and ext2 IFS, but these haven't worked (I couldn't get the former to work, and the latter says that it supports Windows 2008 but gives an error when I try to install it, saying that it only supports up to Windows 2003). I know that there are all kinds of tools to view Linux partitions and that there are filesystems that are compatible with both Linux and Windows, but neither of those options works here (I want to be able to attach and detach the Ubuntu volumes on command, rather than have a permanent partition, and Ubuntu EBS volumes are ext3 by default). Anybody know a good tool I should use?

  Read the article

• How can I remove UNC password from a file

  - by freddoo

  Hi we have an mp4 file on our web server in a virtual directory When we try to access the file we get prompted for a username/password. When I tried to change the path of the virtual directory I got the message 'The following child nodes also define the value of the "UNCPassword" property, which overrides the value you have just set ...' which included the mp4 file that we try to access. How can I remove the UNC Password securing the file? The file is not on a shared drive its on the same drive as the web site root. The funny thing is the path of the virtual directory is not a UNC path it's a full path on the same server d:.....

  Read the article

• I reinstalled OS X and the system was the same as before

  - by slhck

  Strange thing happened. I want so sell my old Macbook and therefore used a disk image of the Snow Leopard DVD that I restored onto an external drive. I booted off the drive and went through the installation steps. Now I really would like to perform "archive and install", as there might be some files that I need later, but I didn't see the option. The only options for installation I had, were, including others, optional printer drivers and Rosetta. So I just clicked through and I wasn't given any other option. After about 45 minutes, my system booted again, and voila, there was my old system. Nothing changed. How should I proceed to actually reset the system? All I have is that Snow Leopard DVD image.

  Read the article

• Installing Intel Rapid Storage Drivers makes my eSATA Drives act weird

  - by Filip Ekberg

  I have a HP 8530w Elitebook this Laptop got an eSATA port which I want to plug my LaCie d2 Quadra V2 1TB harddrive into. It all works well on a fresh install of Windows 7 without the Intel Chipset drivers installed. However when I install the Intel Rapid Storage drivers or the Intel Matrix software my drive seems to "disconnect" when I use it to much. I have a lot of Virtual PC's on the drive and when I start them the disk somewhat disconnects. What could cause this?

  Read the article

• Acer Aspire 1360 Recovery CDs

  - by John

  I have replaced a dead hard disk in an out of warranty Acer Apire 1360 laptop. The two recovery CDs I have dont appear to be bootable, they just contain .hdd and .ghs (image?) files. On the original broken hard drive there was a hidden partition which could be invoked by pressing alt+f10 when booting. You would then be prompted for the 2 recovery CDs to perform the restore. Obviously the new hard drive does not contain the hidden Acer recovery partition. This being the case, how do I go about restoring Win XP? The 2 CDs are called Aspire 1360/1520 Serires Recovery CD Disk 1 of 2 and 2 of 2. Am I missing a futher bootable recovery CD? Can anyone confirm how many restore CDs originally came with the laptop.

  Read the article

• Opinions on NTFS for Mac solution?

  - by AngryHacker

  I am currently using the free NTFS-3G to access my NTFS drive from the Mac. It seems pretty stable (except once in the very beginning, it locked up the Mac and corrupted my NTFS drive, which I then fixed with chkdsk from a PC). However, speed is NOT one of its virtues. In fact, it's painfully slow I've been looking at buying Paragon NTFS for Mac OS X 8.0. Their product comparison PDF claims nearly double the speed (vs NTFS-3G) in almost every category (read, write, etc...). In addition, there is now an unsupported native solution with the snow leopard. Can folks here share their experiences. Is the native solution stable enough to be used for daily work? Should I just go with Paragon?

  Read the article

• Folder Redirection - Explorer requires manual refresh

  - by Pete

  Hello, I am having an issue where - when a users my documents folder is redirected to a DFS share, windows explorer requires a manual refresh after creating a new folder, file, etc. (Interestingly, not when making a new briefcase) I have tried a number of MS knowledge base articles, a hot-fix and a registry change, all with no success. (( http:// support.microsoft.com/?kbid=823291 ; http:// support.microsoft.com/kb/873392 )) The problem only occurs when going through the my documents icon. If I map a home drive for the user to the exact same location (IE - H:\DFS\user\documents) , open that drive and make new folders, then there is no problem. Mapping my documents to H:\ also resolves the issue, however, as we need folder sync and people logging on off site with cached profiles this is not a workable solution (as H: will not map and there will be no access to their docs.) Has anyone managed to figure a fix for this? Thanks, Pete.

  Read the article

< Previous Page | 237 238 239 240 241 242 243 244 245 246 247 248  | Next Page >