Search Results

Search found 6772 results on 271 pages for 'rob effect'.

Page 241/271 | < Previous Page | 237 238 239 240 241 242 243 244 245 246 247 248  | Next Page >

• Power cycles on/off 3 times before booting properly from cold start, no other issues (New System)

  - by James

  Relevant Specs: Sapphire 5850, core i7 920, Seasonic x750 power supply, ECS X58B-A2 mobo. From a cold boot, meaning all power totally disconnected at the wall, the system will power on for less than a second and then power off completely. After two seconds of being powered off this will repeat and on the third "attempt" the computer will boot. To be very specific here is what happens: The power is turned on at the wall and on the psu, the orange stdby LED on the mobo is illuminated but the system is 'off'. I hit the power button on the case or on the mobo itself I hear the relay (?) in the psu closing The case light comes on and the mobo power light comes on. The fans start rotating. Immediately after this the I hear some relay click - the power lights extinguish, the fans stop, the stdby light remains on. Less than 2 seconds pass and the cycle repeats without any intervention from me. On the third attempt it boots normally and the machine runs perfectly. If I do a soft reboot or a full shutdown the computer starts normally the next time. It's only if I pull the power cord or flick the switch off on the PSU that I get the cycling again. Basically any time the stdby light on the mobo goes out. I have removed the graphics card and I get the same problem. I have removed the PSU, hotwired it to the ON position and verified voltages on all lines. The relay does not cycle when I do this. If I connect only the 24 pin ATX connector to the mobo and not the 8 pin ATX12V / CPU connector then I will not get the cycling, the fans run, the power light stays on, but obviously the system can't boot. Disconnecting all fans has no effect on the problem. My feeling it that it's something to do with the motherboard like a capacitor that's taking a long time to charge because it's leaking or something along those lines. But I can't imagine what could be 'wrong' with it and only manifest itself as a problem under these very specific circumstances. Any ideas? Thanks.

  Read the article

• Windows Server 2003 Terminal Server does not give out all available licenses (solved)

  - by Erwin Blonk

  I installed the Terminal Server role in Windows Server 2003 Standard 64-bits. Still, only 2 connections are allowed. The License Manager says that there are 10 Device CALs available, which is correct, and that none are given out. For good measure I let the server reboot, to no effect. Before this, there was another server (same Windows, except that it is 32 bits) active as a licensing server. I removed the role first and then then added it to the new server. I then removed the Terminal Server Licensing Server component off the old one and added it to the new one. After that, I added to licenses. When that didn't give the required result, I rebooted to new server. Still, the new server, with licenses and all, acts as if it has the 2 license RDP. The server are all stand-alone, there is no active directory been set up. Both servers are in different workgroups. Update (4/12/10): The server has changed the entries in the Terminal Server Licensing a few times. After installing the licenses it added an entry of which the exact phrasing I forgot but it was about temporary Windows 2003 device licenses. Later it added Windows Server 2003 - TS Per Device CAL. The temporary held 2 licenses (standard RDP licenses, I think) and the other 10. At some point, seemingly unrelated from the testing we did, it used a licenses from the new pool. This morning, 2 licenses were used from the pool of 10 and only 1 from the temporary/RDP pool (I wish I had screenshots to show, it changed every few hours oir so it seems). Although I had already activated the server over the internet, and re-activated it, I decided to go through the whole procedure by phone. Update 2 (4/12/10) The problem has been solved. It seems the activation over the web, while it said to have succeeded, did not work correctly. After activating by phone, it did work. What was different from the old setup and what put me on the wrong foot from that moment, was that I now need to create seperate user account because a session with one user account will be taken over by someone else when that account is used by that person. On the previous server, it was possible to open several sesions with the same account. We now use Per Device licenses, I'm not sure what was used before. Thanks all for the replies.

  Read the article

• How to allow local LAN access while connected to Cisco VPN?

  - by Ian Boyd

  How can I maintain local LAN access while connected to Cisco VPN? When connecting using Cisco VPN, the server has to ability to instruct the client to prevent local LAN access. Assuming this server-side option cannot be turned off, how can allow local LAN access while connected with a Cisco VPN client? I used to think it was simply a matter of routes being added that capture LAN traffic with a higher metric, for example: Network Destination Netmask Gateway Interface Metric 10.0.0.0 255.255.0.0 10.0.0.3 10.0.0.3 20 <--Local LAN 10.0.0.0 255.255.0.0 192.168.199.1 192.168.199.12 1 <--VPN Link And trying to delete the 10.0.x.x -> 192.168.199.12 route don't have any effect: >route delete 10.0.0.0 >route delete 10.0.0.0 mask 255.255.0.0 >route delete 10.0.0.0 mask 255.255.0.0 192.168.199.1 >route delete 10.0.0.0 mask 255.255.0.0 192.168.199.1 if 192.168.199.12 >route delete 10.0.0.0 mask 255.255.0.0 192.168.199.1 if 0x3 And while it still might simply be a routing issue, attempts to add or delete routes fail. At what level is Cisco VPN client driver doing what in the networking stack that takes overrides a local administrator's ability to administer their machine? The Cisco VPN client cannot be employing magic. It's still software running on my computer. What mechanism is it using to interfere with my machine's network? What happens when an IP/ICMP packet arrives on the network? Where in the networking stack is the packet getting eaten? See also No internet connection with Cisco VPN Cisco VPN Client interrupts connectivity to my LDAP server Cisco VPN stops Windows 7 Browsing How can I prohibit the creation of a route in Windows XP upon connection to Cisco VPN? Rerouting local LAN and Internet traffic when in VPN VPN Client "Allow local LAN Access" Allow Local LAN Access for VPN Clients on the VPN 3000 Concentrator Configuration Example LAN access gone when I connect to VPN Windows XP Documentation: Route Edit: Things I've not yet tried: >route delete 10.0.* Update: Since Cisco has abandoned their old client, in favor of AnyConnect (HTTP SSL based VPN), this question, unsolved, can be left as a relic of history. Going forward, we can try to solve the same problem with their new client.

  Read the article

• Import/rip/convert DVD to Adobe Premiere Pro for Mac

  - by alexyu2010

  For those who want to edit their videos, Adobe Premiere Pro will inevitably a good choice, it is a professional, real time, timeline based video editing software application that supports many video editing cards and plug-ins for accelerated processing, additional file format support and video/audio effects. Although Adobe Premiere Pro is said to be for professionals, is not so complicated that a hobbyist can't excel at using it in an hour or so. General file formats supported by Adobe Premiere Pro Up to now, Adobe Creative Suite has released several versions of Adobe Premiere Pro, including Adobe Premiere 1.0, Adobe Premiere 2.0, Adobe Premiere Pro CS3, Adobe Premiere Pro CS4 and the newly published Adobe Premiere Pro CS5. Although I saw diversity in file formats they support, I did find some common file formats supported by all of them, such as AVI, MOV, MPG. Importing DVD, Adobe Premiere Pro says "NO" It is obvious to all of us that Adobe Premiere Pro will never give DVD a hug, and it isn't rare to see that many people are really confused when they want to import their DVDs to Adobe Premiere Pro for editing. What to do? Yes, you may have noticed that, there is only a way out, that is ripping your DVDs to some formats workable with Adobe Premiere Pro natively, and this is what DVD to Adobe Premiere Pro can do. Importing DVD to Adobe Premiere Pro on Mac DVD to Adobe Premiere Pro converter for Mac is the specially designed application for ripping/converting DVD movies, DVD VOB files or DVD clips to Adobe Premiere Pro compatible AVI, MOV, MPG files with either DVD ripping tool and video converting tool within the versatile DVD to Adobe Premiere Pro converter who is a powerful program for dealing with DVD and videos perfectly. Mac DVD to Adobe Premiere Pro converter can work with a wide variety of files including DVD, VOB, AVI, WMV, MPG, MOV, MP4, DV, FLV, MKV, ASF, SWF, HD video for using with other editing tools like iMovie, FCP etc, play on QuickTime, iTunes, put on portable devices like iPod, iPhone, iPad, iRiver, BlackBerry, Gphone, Mobile Phone or upload to webistes such as YouTube, MySpace. DVD to Adobe Premiere Pro converter for Mac can also help you do some basic editing. You can trim, crop your DVD movie or DVD clip, apply special effect to make it more artistic, merge several DVD clips to a single one or tweak the output parameters for video and audio separately to get a better quality rendering. Besides, to get a good common of the process the preview widnows is also available for you.

  Read the article

• Ubuntu - Ruby Daemon script creates two processes - sh and ruby - PID file points at sh, not ruby

  - by Jonathan Scoles

  The PID file for a ruby process I have running as a daemon is getting the wrong PID. It appears that running /etc/init.d/sinatra start creates two processes - sh and ruby, and the PID that ends up in the PID file is that of the sh process. This means that when I then run /etc/init.d/sinatra stop or /etc/init.d/sinatra restart, it is killing sh and leaving the ruby process still running. I'd like to know a) why is my script launching two processes - sh and ruby, and not just ruby, and b) how do I fix it to just launch ruby? Details of the setup: I have a small Sinatra server set up on an ubuntu server, running as a daemon. It is set to automatically at server startup run a script named sinatra in /etc/init.d that launches the a control script control.rb, which then runs a ruby daemon command to start the server. The script is run under the 'sinatrauser' account, which has permissions for the directories the script needs. contents of /etc/init.d/sinatra #!/bin/bash # sinatra Startup script for Sinatra server. sudo -u sinatrauser ruby /var/www/sinatra/control.rb $1 RETVAL=$? exit $RETVAL To install this script, I simply copied it to /etc/init.d/ and ran sudo update-rc.d sinatra defaults contents of /var/www/sinatra/control.rb require 'rubygems' require 'daemons' pwd = Dir.pwd Daemons.run_proc('sinatraserver.rb', {:dir_mode => :normal, :dir => "/opt/pids/sinatra"}) do Dir.chdir(pwd) exec 'ruby /var/www/sinatra/sintraserver.rb >> /var/log/sinatra/sinatraOutput.log 2>&1' end portion of output from ps -A 6967 ? 00:00:00 apache2 10181 ? 00:00:00 sh <--- PID file gets this PID 10182 ? 00:00:02 ruby <--- Actual ruby process running Sinatra 12172 ? 00:00:00 sshd The PID file gets created in /opt/pids/sinatra/sinatraserver.rb.pid, and always contains the PID of the sh instance, which is always one less than the PID of the ruby process EDIT: I tried micke's solution, but it had no effect on the behavior I am seeing. This is the output from ps -A f. This output looks the same whether I use sudo -u sinatrauser ... or su sinatrauser -c ... in the service start script in /etc/init.d. 1146 ? S 0:00 sh -c ruby /var/www/sinatra/sinatraserver.rb >> /var/log/sinatra/sinatraOutput.log 2>&1 1147 ? S 0:00 \_ ruby /var/www/sinatra/sinatraserver.rb

  Read the article

• Using WSUS Admin Console from outside domain

  - by Nick

  Environment: I have a workstation on our primary domain. We have a primary WSUS Server that is the upstream server of 8 different testing domains. The Primary WSUS server is not part of any domain. Routing is configured between my workstation and the Primary WSUS server. I can RDP to the Primary WSUS sever without any problem. The router is configured to forward any any between my workstation and the Primary WSUS server. This WSUS server cannot be part of a domain due to external requirements (I can't change them) on the lab I work in. The version of WSUS is WSUS 3.0 SP 2 What I want to do: I need to connect to the WSUS server with the WSUS Admin console from my local workstation. The end goal is to connect via Powershell and manage with that. I also need to take what I do here and port it to the 8 test domains so I can manage those WSUS servers. The routing is all in place so I can talk to the servers, it's just connecting to the WSUS console that is causing problems. The problem: I cannot get my workstation to connect to the WSUS Console. I get one of the following errors depending on the setup. 1st error: Cannot connect to 'WSUS'. You do not have the permissions required to access this WSUS server. To connect to the server you must be a member of the WSUS Administrators or WSUS Reporters security groups I also get the warning 7012 from the event log that says the same thing. 2nd error: Cannot connect to 'WSUS'. The server may be using another port or different Secure Sockets Layer setting. What I have tried: So far I have configured IIS for Anonymous Authentication on both the WSUS Administration and ApiRemoting30 using an account will call WSUS_User. With this in place, I get the 1st error. When I do this though, the local WSUS Console cannot be used either. Reverting back to only Windows Authentication allows the local console to work, but the remote console now give the 2nd error. I have confirmed the port, and that there is no SSL in use (which is a policy that is pushed from above, that I cannot effect). I have placed WSUS_User in the groups mentioned above, but it still does not connect. I made sure WSUS_User has full access on C:\Program Files\Update Services and C:\Program Files\Update Services\WebServices I am not very familiar with the workings of WSUS or IIS, and have gone as far as I can figure out on my own. Googling these errors all take me to the same steps about Anonymous Authentication and configuring permissions on folders. Note: I have cross-posted this to StackOverflow as well.

  Read the article

• Virtual Network Interface and NAT disables localhost access for MySQL and Apache

  - by Interarticle

  I'm running an Ubuntu Server 12.04, and recently I configured it to do NAT for my laptop. Since the server has only one NIC, I followed instructions online to create a virtual network device (eth0:0) that has a LAN IP address, then further configured iptables and UFW to allow internet sharing. However, just a few days ago, I discovered that one of the PHP pages hosted on the server failed for no apparent reason. A little digging revealed that the MySQL server started refusing connections from localhost. The same happened with a page (PhpMyAdmin) that was configured to be accessible only from localhost (in Apache2). The error, as shown by $mysql --protocol=tcp -u root -p looks like ERROR 1130 (HY000): Host '<host name of eth0>' is not allowed to connect to this MySQL server However, the funny thing is, I configured the mysql server to allow root access from localhost (only). Moreover, the mysql server listens only on 127.0.0.1:3306, as shown by: sudo netstat -npa | head Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 127.0.0.1:3306 0.0.0.0:* LISTEN 1029/mysqld which means that the connection could have only come from 127.0.0.1 (Note that MySQL is working because I can still connect to it via unix domain sockets) In effect, it seems that all tcp connections originating from 127.0.0.1 to 127.0.0.1 appear to any local daemon to come from the eth0 IP address. Indeed, apache2 allowed me to access PhpMyAdmin after I added allow <eth0 IP address>. The following are my network configurations (redacted): /etc/hosts: 127.0.0.1 localhost 211.x.x.x <host name of eth0> <server name> #IPv6 Defaults follows .... /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 211.x.x.x netmask 255.255.255.0 gateway 211.x.x.x dns-nameservers 8.8.8.8 # dns-* options are implemented by the resolvconf package, if installed dns-search xxxxxxx.com hwaddress ether xx:xx:xx:xx:xx:xx auto eth0:0 iface eth0:0 inet static address 192.168.57.254 netmask 255.255.254.0 broadcast 192.168.57.255 network 192.168.57.0 /etc/ufw/sysctl.conf: #Uncommented the following lines net/ipv4/ip_forward=1 net/ipv6/conf/default/forwarding=1 /etc/default/ufw: DEFAULT_FORWARD_POLICY="ACCEPT" #Changed DROP to ACCEPT /etc/init/internet-sharing.conf (upstart script I wrote), section pre-start script: iptables -A FORWARD -o eth0 -i eth0:0 -s 192.168.57.22 -m conntrack --ctstate NEW -j ACCEPT iptables -A FORWARD -m conntrack --ctstate ESTABLISHED,RELATED -j ACCEPT iptables -A POSTROUTING -t nat -j MASQUERADE Note again that my problem here is that programs cannot access localhost tcp services, from the server itself, and that access is blocked because the services have access control allowing only 127.0.0.1. I have no problem connecting (as in TCP connections) to services via tcp, even if the services listen only on 127.0.0.1. I do NOT want to connect to the services from another computer.

  Read the article

• Can you set up a gaming LAN using OpenVPN installed in a VMware guest OS and be playing the game on the host OS?

  - by Coder

  I would like to setup a gaming VPN. Ie. I have some games that work over LAN and would like to play them with people that are not on my LAN. I know I can do this with OpenVPN. My ultimate goal would be to run OpenVPN portably on my host OS and not even need any virtualization. As such i don't want to install it on my host, but i'm fine with running it portably. I'm even fine with temporarily adding registry keys, and then running a .reg file to remove these entries once i'm done. To this effect i have installed OpenVPN on a virtual machine and diffed the registry. I then manually (using a .reg file) added all the keys that seem important on my host OS and copied the installation folder of OpenVPN onto my host machine. Then i try to run openVPN GUI 1.0.3 as a test and it says "Error opening registy for reading (HKLM\SOFTWARE\OpenVPN). OpenVPN is probably not installed". I verified that that key is indeed in the registry with all subkeys and it looks correct. I have tried running the GUI as an administrator and in compatibility mode with no success. I am running Windows 7. If this fails then i would be happy with installing OpenVPN on a virtual machine in VMWare but they key is that i will be running the game installed on my host machine. The first question for this option is if this is even possible. The second is, that I can't get the VM to have internet access if I use bridging but i can if i use NAT. Is it possible to do this game VPN setup with VMWare guest OS running using NAT? Summary of questions: -Is it possible to run openVPN portably and if so what did i miss above? -If it's not possible to run it portably, then can setup a gaming LAN by installing OpenVPN in a guest OS with NAT and how can i do this? -If the above is not possible then can i install OpenVPN in a guest using bridging and if so how can i set this up with a Windows 7 host and Windows XP guest as currently i can't get the guest to be able to access the internet in bridging mode, but it working in NAT mode. -In general is there any good documentation on setting up a gaming LAN with OpenVPN (i am using 2.1.4) as i have never set up a VPN of any sort before so any help would be much appreciated. Thanks!

  Read the article

• Postfix SMTP auth not working with virtual mailboxes + SASL + Courier userdb

  - by Greg K

  So I've read a variety of tutorials and how-to's and I'm struggling to make sense of how to get SMTP auth working with virtual mailboxes in Postfix. I used this Ubuntu tutorial to get set up. I'm using Courier-IMAP and POP3 for reading mail which seems to be working without issue. However, the credentials used to read a mailbox are not working for SMTP. I can see from /var/log/auth.log that PAM is being used, does this require a UNIX user account to work? As I'm using virtual mailboxes to avoid creating user accounts. li305-246 saslauthd[22856]: DEBUG: auth_pam: pam_authenticate failed: Authentication failure li305-246 saslauthd[22856]: do_auth : auth failure: [user=fred] [service=smtp] [realm=] [mech=pam] [reason=PAM auth error] /var/log/mail.log li305-246 postfix/smtpd[27091]: setting up TLS connection from mail-pb0-f43.google.com[209.85.160.43] li305-246 postfix/smtpd[27091]: Anonymous TLS connection established from mail-pb0-f43.google.com[209.85.160.43]: TLSv1 with cipher ECDHE-RSA-RC4-SHA (128/128 bits) li305-246 postfix/smtpd[27091]: warning: SASL authentication failure: Password verification failed li305-246 postfix/smtpd[27091]: warning: mail-pb0-f43.google.com[209.85.160.43]: SASL PLAIN authentication failed: authentication failure I've created accounts in userdb as per this tutorial. Does Postfix also use authuserdb? What debug information is needed to help diagnose my issue? main.cf: # TLS parameters smtpd_tls_cert_file = /etc/ssl/certs/smtpd.crt smtpd_tls_key_file = /etc/ssl/private/smtpd.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # SMTP parameters smtpd_sasl_local_domain = smtpd_sasl_auth_enable = yes smtpd_sasl_security_options = noanonymous broken_sasl_auth_clients = yes smtpd_recipient_restrictions = permit_sasl_authenticated,permit_mynetworks,reject_unauth_destination smtp_tls_security_level = may smtpd_tls_security_level = may smtpd_tls_auth_only = no smtp_tls_note_starttls_offer = yes smtpd_tls_CAfile = /etc/ssl/certs/cacert.pem smtpd_tls_loglevel = 1 smtpd_tls_received_header = yes smtpd_tls_session_cache_timeout = 3600s tls_random_source = dev:/dev/urandom /etc/postfix/sasl/smtpd.conf pwcheck_method: saslauthd mech_list: plain login /etc/default/saslauthd START=yes PWDIR="/var/spool/postfix/var/run/saslauthd" PARAMS="-m ${PWDIR}" PIDFILE="${PWDIR}/saslauthd.pid" DESC="SASL Authentication Daemon" NAME="saslauthd" MECHANISMS="pam" MECH_OPTIONS="" THREADS=5 OPTIONS="-c -m /var/spool/postfix/var/run/saslauthd" /etc/courier/authdaemonrc authmodulelist="authuserdb" I've only modified one line in authdaemonrc and restarted the service as per this tutorial. I've added accounts to /etc/courier/userdb via userdb and userdbpw and run makeuserdb as per the tutorial. SOLVED Thanks to Jenny D for suggesting use of rimap to auth against localhost IMAP server (which reads userdb credentials). I updated /etc/default/saslauthd to start saslauthd correctly (this page was useful) MECHANISMS="rimap" MECH_OPTIONS="localhost" THREADS=0 OPTIONS="-c -m /var/spool/postfix/var/run/saslauthd -r" After doing this I got the following error in /var/log/auth.log: li305-246 saslauthd[28093]: auth_rimap: unexpected response to auth request: * BYE [ALERT] Fatal error: Account's mailbox directory is not owned by the correct uid or gid: li305-246 saslauthd[28093]: do_auth : auth failure: [user=fred] [service=smtp] [realm=] [mech=rimap] [reason=[ALERT] Unexpected response from remote authentication server] This blog post detailed a solution by setting IMAP_MAILBOX_SANITY_CHECK=0 in /etc/courier/imapd. Then restart your courier and saslauthd daemons for config changes to take effect. sudo /etc/init.d/courier-imap restart sudo /etc/init.d/courier-authdaemon restart sudo /etc/init.d/saslauthd restart Watch /var/log/auth.log while trying to send email. Hopefully you're good!

  Read the article

• OCZ Vertex 2 not recognized by Ubuntu installer

  - by Zsub

  As I boot into the Ubuntu 10.10 (or 11.04, doesn't matter) live environment or installer, it just refuses to recognise my Vertex 2. It reports the disk as ATA and not supporting smart, shows no serial number, and doesn't list the size correctly. All fdisk tells me is Unable to read /dev/sda (it's the only storage in the PC). I'm now running a temporary install of Windows 7 off of it, which worked like a charm, so where am I going wrong with Ubuntu... Specs: Asus M4N68T-M LE V2 (BIOS 0702, most recent) OCZ Vertex 2 SSD 60 GB Amd Athlon II X4 640 Patriot PSD34G13332 4GB DDR3 ram (two banks) EDIT I installed a second drive, installed Ubuntu on that and booted, it recognised the SSD just fine. I'm now trying to apt-get upgrade the live-environment. I wonder if there is any way to sort of install Ubuntu from Ubuntu (I boot into the working install on the other drive, install it on the SSD and then boot from the SSD). EDIT2 Ok, so that doesn't work. The install detects the SSD, however, it cannot format it. EDIT3 After a fresh boot I can read out SMART-data and even perform a read-benchmark, but if I try to format it, or do a write-bench, it'll crap out and after that it says SMART is not supported. So basically it seems I can't write to the disk, as it will stop working when I do, I will try to run repeated read-benchmarks to see if that has any effect. EDIT4 I'm running several read benchmarks on the drive right now, they give results that are to be expected from an SSD. If the read-benches don't fail, I can use fdisk on the disk, but it is now stuck trying to re-read the partition table after issueing the 'w' command. EDIT5 Parted Magic did recognize the drive and with hdparm -I even could tell me the drive was in a frozen state. I powercycled it (just pull out the plug from the SSD and plug it back in) and it wasn't frozen anymore. After that I could upgrade the firmware on the drive (still using Parted Magic) and format it to Ext4. After I rebooted into the Ubuntu installer, it wouldn't get recognized and hdparm didn't want to talk to it saying HDIO_DRIVE_CMD(identify) failed: Invalid exchange. EDIT6 For some reason if I enable one of the RAID controllers (the one the SSD is connected to, obviously) Ubuntu will let me format it, mount it and write to it. The installer also recognizes it. However if the raid controller is enabled but no array is defined the motherboard can't boot from it :(

  Read the article

• So I want to separate my Program Files from the hard disk with the other system files. What is the b

  - by grg-n-sox

  So I am running Windows 7 as my only OS. I have two hard drives on my computer. The first one is a 74GB Western Digital 10K RPM Raptor. The second one is a 1TB Seagate Barracuda (couldn't remember if it was a 7200.12 or some other decimal after the 7200). The OS in installed to the Raptor and I am just using the Barracuda for storage. With this setup, in case you couldn't guess already, the Raptor fills up quick and I am constantly having to maintain file locations. And although it is nice to have that quicker boot time and program loading, the time spent maintaining the drive makes me waste more time overall. So I am looking for a way to try to keep it clear while still keeping up system loading speeds. A performance hit on games and such is easily acceptable and as long as I can guarantee a 5GB space on the Raptor, I can always just temporarily move the disc image there. So I am figuring that having games installed like Boarderlands and Mass Effect, as well as having large files such as linux distro DVD disc images in My Documents, I probably should be moving my personal files and Program Files directories to the Barracuda. I currently have folders on the Barracuda for this, but this means routinely copying files over and I can't really do anything with the Program Files folder that already exists. The best I can do is remember to designate the install directory of any program installation to the alternative install directory, which I can't seem to get to ever work right with Steam. With that in mind, is there a way that is not too drastic to let me just change some folders and system settings once and everything works fine afterwards for my setup? I have considered just reinstalling Windows 7 to the Barracuda but that would defeat the purpose of the Raptor except for running disc images off of. I am also heard a bit about being able to use symlinks to fix this, but I have also heard that symlinks in Windows are not necessarily the same and not as well supported on Windows. An example a friend mentioned was something about how if you have a symlink in Windows on a small hard drive to a large hard drive and the contents the symlink points to is larger than the small hard drive's capacity, then Windows will think the smaller hard drive is full. So is there a fix/workaround that will let me use symlinks across hard drives without the issues or is there a better solution I am not being told about, not mentioning, or not thinking of?

  Read the article

• nginx proxypath https redirect fails without trailing slash

  - by Thermionix

  I'm trying to setup Nginx to forward requests to several backend services using proxy_pass. The links on the pages that lack trailing slashes do have https:// in front, but get redirected to a http request with a trailing slash - which ends in connection refused - I only want these services to be available through https. So if a link is too https://example.com/internal/errorlogs in a browser when loaded https://example.com/internal/errorlogs gives Error Code 10061: Connection refused (it redirects to http://example.com/internal/errorlogs/) If I manually append the trialing slash https://example.com/internal/errorlogs/ it loads I've tried with varied trailing forward slashes appended to the proxypath and location in proxy.conf to no effect, have also added server_name_in_redirect off; This happens on more than one app under nginx, and works in apache reverse proxy Config files; proxy.conf location /internal { proxy_pass http://localhost:8081/internal; include proxy.inc; } .... more entries .... sites-enabled/main server { listen 443; server_name example.com; server_name_in_redirect off; include proxy.conf; ssl on; } proxy.inc proxy_connect_timeout 59s; proxy_send_timeout 600; proxy_read_timeout 600; proxy_buffer_size 64k; proxy_buffers 16 32k; proxy_pass_header Set-Cookie; proxy_redirect off; proxy_hide_header Vary; proxy_busy_buffers_size 64k; proxy_temp_file_write_size 64k; proxy_set_header Accept-Encoding ''; proxy_ignore_headers Cache-Control Expires; proxy_set_header Referer $http_referer; proxy_set_header Host $host; proxy_set_header Cookie $http_cookie; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-Host $host; proxy_set_header X-Forwarded-Server $host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header X-Forwarded-Ssl on; proxy_set_header X-Forwarded-Proto https; curl output -$ curl -I -k https://example.com/internal/errorlogs/ HTTP/1.1 200 OK Server: nginx/1.0.5 Date: Thu, 24 Nov 2011 23:32:07 GMT Content-Type: text/html;charset=utf-8 Connection: keep-alive Content-Length: 14327 -$ curl -I -k https://example.com/internal/errorlogs HTTP/1.1 301 Moved Permanently Server: nginx/1.0.5 Date: Thu, 24 Nov 2011 23:32:11 GMT Content-Type: text/html;charset=utf-8 Connection: keep-alive Content-Length: 127 Location: http://example.com/internal/errorlogs/

  Read the article

• Server load spikes several times a day, load average for the past month is 5 times the load average all year

  - by AMF

  My Munin notifications set up for our (Debian) LAMP cluster have been notifying me continuously that our load on our production machine has been at dangerous levels. While the average load all year typically runs between 2 and 8, the load in the past month and only the past month -- has been skyrocketing to 10, 18, and occasionally even 50-60. The spikes last only 5-10 minutes at a time and occur about every 2-3 hours. The spikes do not effect performance only because I have a script that sends traffic off our server to a mirror CDN when the load goes above 10. I've looked for cron jobs that correlate with this timeframe but there is nothing I can see that would cause this. Site traffic is also normal (we receive about 200K visits per day). I'm also trying to think of anything I've changed around the time this problem began, and I really cannot think of anything. This is probably not much to go on. Maybe there is a clue in the top print-out (below) that I'm not seeing. How do I proceed to find the cause? -- Typical top when the load is NOT spiking: top - 11:13:09 up 472 days, 25 min, 1 user, load average: 6.08, 4.29, 3.80 Tasks: 105 total, 1 running, 104 sleeping, 0 stopped, 0 zombie Cpu(s): 41.2%us, 5.8%sy, 0.0%ni, 49.5%id, 2.7%wa, 0.1%hi, 0.7%si, 0.0%st Mem: 3369592k total, 2166980k used, 1202612k free, 559504k buffers Swap: 2650684k total, 1892k used, 2648792k free, 1129116k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 32046 apache 15 0 36300 12m 9828 S 20 0.4 0:01.97 apache2 32679 apache 15 0 36568 13m 10m S 19 0.4 0:01.69 apache2 31441 apache 15 0 36616 13m 10m S 19 0.4 0:04.13 apache2 31477 apache 15 0 36596 13m 9.8m S 15 0.4 0:01.99 apache2 31993 apache 15 0 36876 16m 12m S 12 0.5 0:02.01 apache2 31782 apache 15 0 36836 14m 10m S 8 0.4 0:02.17 apache2 32198 apache 15 0 36536 13m 10m S 7 0.4 0:01.59 apache2 880 apache 15 0 36508 9708 6236 S 7 0.3 0:00.42 apache2 31945 apache 17 0 36876 16m 13m S 5 0.5 0:03.17 apache2 32197 apache 16 0 36636 10m 7504 S 5 0.3 0:02.70 apache2 32326 apache 15 0 37024 11m 7632 S 5 0.3 0:02.15 apache2 32565 apache 15 0 37280 13m 9.8m S 5 0.4 0:03.75 apache2 32676 apache 15 0 36896 16m 12m S 4 0.5 0:00.95 apache2 32678 apache 15 0 36536 12m 9692 S 4 0.4 0:02.27 apache2 974 apache 16 0 37064 9888 6016 D 4 0.3 0:00.13 apache2 32150 apache 16 0 36832 13m 10m S 3 0.4 0:01.74 apache2 31780 apache 16 0 36848 11m 7660 S 3 0.3 0:02.87 apache2

  Read the article

• Slow Windows Explorer on Windows 7

  - by MadBoy

  I have Laptop with i7 (4 cores), 8GB ram and SSD OCZ Vertex 3 MaxIOPS which in testing that I did just now does 400mb/s+ read/write. However the responsiveness of Windows Explorer is far from being perfect. Opening up Computer, Documents, going into folders is very slow (1-5seconds). I don't have any viruses or spyware and I have tried changing properties to optimize view for General Items. I tried disabling Search Indexer but it made search in Outlook 2010 crawl and didn't bring any other effect. Even double clicking on file takes some time to open things up (like clicking a Word document). I don't have any drives mapped, my computer is not joined to domain. I have multiple VPN connections that I connect to but they all have disabled default gateways. I tried using CC Cleaner or some Windows 7 Tweaks app to disable some things. I am power user using Visual Studio, Tortoise SVN and other developer/administration apps. Any non obvious ideas? Edit: So I've been trying to pinpoint where the issue comes from and it seems that straight after reboot Windows Explorer opens very fast, when I load 3-4 programs (Royal TS, Visual Studio, Outlook) it's noticeably slower and the more programs I have it gets worse. After I start closing programs it starts working better and if I leave 2 open it's fast again. I tried doing some research with DiskMon and other programs from sysinternals but couldn't find anything suspicious. Below are stats during normal usage with a lots of programs open: - Ram usage with a lot of programs open and no swap file (i disabled it for testing): 6.95GB - CPU usage: 15%, none of the cores takes more then 50% (I have VS 2010 open x 4) HD Tune Pro: OCZ-VERTEX3 MI Benchmark Test capacity: full Read transfer rate Transfer Rate Minimum : 363.9 MB/s Transfer Rate Maximum : 505.5 MB/s Transfer Rate Average : Access Time : Burst Rate : CPU Usage : HD Tune Pro: OCZ-VERTEX3 MI File Benchmark Drive C: Transfer rate test File Size: 500 MB Sequential read 484102 KB/s Sequential write 444714 KB/s Random read 7779 IOPS Random write 16888 IOPS Random read (queue depth = 32) 73007 IOPS Random write (queue depth = 32) 69790 IOPS HD Tune Pro: OCZ-VERTEX3 MI Random Access Test capacity: full Read test Transfer size operations / sec avg. access time max. access time avg. speed 512 bytes 3260 IOPS 0.306 ms 2.106 ms 1.592 MB/s 4 KB 4161 IOPS 0.240 ms 2.006 ms 16.256 MB/s 64 KB 2382 IOPS 0.419 ms 2.367 ms 148.934 MB/s 1 MB 449 IOPS 2.225 ms 4.197 ms 449.407 MB/s Random 809 IOPS 1.235 ms 6.551 ms 410.527 MB/s HD Tune Pro: OCZ-VERTEX3 MI Extra Tests Test capacity: full Random seek 3975 IOPS 0.252 ms 1.941 MB/s Random seek 4 KB 4245 IOPS 0.236 ms 16.583 MB/s Butterfly seek 4086 IOPS 0.245 ms 1.995 MB/s Random seek / size 64 KB 3812 IOPS 0.262 ms 58.606 MB/s Random seek / size 8 MB 120 IOPS 8.348 ms 485.737 MB/s Sequential outer 4524 IOPS 0.221 ms 282.721 MB/s Sequential middle 4429 IOPS 0.226 ms 276.818 MB/s Sequential inner 5504 IOPS 0.182 ms 344.000 MB/s Burst rate 4472 IOPS 0.224 ms 279.475 MB/s

  Read the article

• Messages stuck in SMTP queue - Exchange 2003

  - by Diav

  I need your help people ;-) I have a problem with messages coming into our Exchange Server and ones going out through it. Basically, the messages are stuck in the SMTP queue. A message will come into the server, I can see it listed under "Exchange System Manager", but if you list the properties of the message queue it says something like 00:10 SMTP Message queued for local delivery 00:10 SMTP Message delivered locally to [email protected] 00:10 SMTP Message scheduled to retry local delivery 00:11 SMTP Message delivered locally to [email protected] 00:11 SMTP Message scheduled to retry local delivery etc etc For outgoing message list looks like this: 10:55 SMTP: Message Submitted to Advanced Queuing 10:55 SMTP: Started Message Submission to Advanced Queue 10:55 SMTP: Message Submitted to Categorizer 10:55 SMTP: Message Categorized and Queued for Routing 10:55 SMTP: Message Routed nad Queued for Remote Delivery And the end - since then status didn't change, message is in queue, I am forcing connection from time to time but without an effect. I checked connection with smarthost (used telnet for that) and everything seems to work correctly, so the problem is probably on exchange side. I am using Exchange Server 2003 running on Small Business Server 2003. I don't have any antivirus installed on server. Remaining free space on each partition is over 3Gb, on partition with data bases - it is over 12Gb. All was working good and without problems since 2005, problems started in half of this june - messages started going out and being stuck almost randomly (I don't see a pattern yet, some are going out, some are not, some are going after several hours). I don't know what to do, what to check more, so please, any ideas? Best regards, D. edit Priv1.edb has 14,5GB and priv1.stm 2,6GB - together those files have more than 16GB - can it be the reason? If yes, then what? Indeed, I haven't thought that it can have something in common with my problem, but several users reported recent problems with Outlook Web Access - they can log in, they see the list of their mails, but they can't see the content of their emails. Although when they are connecting with Outlook 2003/2007 - there is no such problem, only with OWA there is. edit2 So,.. It works now, and I have to admit that I am not really sure what the problem was (hope it won't come back). What have I done: Cleaned up some mailboxes to reduce size of them Dismounted Information Store Defragmentated data base files ( I used eseutil: c:\program files\exchsrvr\bin eseutil /d g:\data base\Exchsrvr\MDBDATA\priv1.edb ) Mounted Information Store back ..and before I managed to do anything else - my queue started moving, elements which were kept there already for days - started moving and after few minutes everything was sent, both, outside and locally. But: priv1.edb is still big (13 884 203 008), priv1.stm as well (2 447 384 576), so this is probably not the issue of size of the file. And if not this, so what was that? And if that was issue of size of the file, then soon it will repeat - is there something I can do to avoid it ?

  Read the article

• DNS and DHCP dies after ~2 days of use on ClearOS

  - by TheLQ

  I'm using ClearOS (based on CentOS, so any info specific to it should apply here) as a gateway, DHCP, and DNS server. I had this server running perfectly for a month or two before replacing it with another server. However due DNS and DHCP failing 2 days in and a host of other performance issues (the box was a little underpowered), I changed back to the origional server. However 2 days in DHCP and DNS are failing again, and I'm out of idea's on why. In both cases to my knowledge no network or server changes occurred after installation. Right after installing (and at least a day in) DNS and DHCP was working just fine. However later (Day 2) I get a call saying their internet is down (translation: Nobody can get to websites because DNS is down) I've tried to fix the problem by checking if the dnsmasq is even running (it is), restarting the service, and restarting the server to no effect. I do have two internal servers that have static DHCP leases but one's lease must of expired as I can't connect to it anymore. I'm hesitant to do any dhcp testing on the last server as I'll not be able to connect to it anymore. Is there anything anyone can think of on why DNS and DHCP would fail 2 days in to running perfectly? More info: Running dnsmasq in debug mode. This is all that's displayed even when running nslookup quackwall. I'm not sure though if nslookup commands should show up in the log [root@quackwall ~]# /usr/sbin/dnsmasq -dq dnsmasq: started, version 2.49 cachesize 150 dnsmasq: compile time options: IPv6 GNU-getopt no-DBus no-I18N DHCP TFTP dnsmasq-dhcp: DHCP, IP range 10.0.0.100 -- 10.0.0.254, lease time 12h dnsmasq: reading /etc/resolv.conf dnsmasq: using nameserver 74.128.17.114#53 dnsmasq: using nameserver 74.128.19.102#53 dnsmasq: read /etc/hosts - 5 addresses dnsmasq-dhcp: read /etc/ethers - 2 addresses On the other server DNS and the Gateway are all configured correctly (10.0.0.2 is quackwall) lordquackstar@quackgame:~$ netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 10.0.0.0 0.0.0.0 255.255.240.0 U 0 0 0 eth0 0.0.0.0 10.0.0.2 0.0.0.0 UG 0 0 0 eth0 lordquackstar@quackgame:~$ cat /etc/resolv.conf nameserver 10.0.0.2 domain highwow.lan search highwow.lan

  Read the article

• How to troubleshoot performance issues of PHP, MySQL and generic I/O

  - by jbx

  I have a WordPress based website running on a shared hosting. Its response time is very decent (around 2s to retrieve the HTML page and 5s to load all the resources). I was planning to move it to a dedicated virtual server (Ubuntu 12.04 LTS), which should theoretically improve things and make them more consistent given its not shared. However I observed severe performance degredation, with the page taking 10seconds to be generated. I ruled out network issues by editing /etc/hosts on the server and mapping the domain to 127.0.0.1. I used the Apache load tester ab to get the HTML, so JS, CSS and images are all excluded. It still took 10 seconds. I have Zpanel installed on the server which also uses MySQL, and its pages come up quite fast (1.5s) and also phpMyAdmin. Performing some queries on the wordpress database directly through phpMyAdmin returns them quite fast too, with query times in the 10 to 30 millisecond region. Memory is also sufficient, with only 800Mb being used of the 1Gb physical memory available, so it doesn't seem to be a swap issue either. I have also installed APC to try to improve the PHP performance, but it didn't have any effect. What else should I look for? What could be causing this degradation in performance? Could it be some kind of I/O issue since I am running on a cloud based virtual server? I wish to be able to raise the issue with my provider but without showing actual data from some diagnosis I am afraid he will just blame my application. UPDATE with sar output (every second) when I did an HTTP request: 02:31:29 CPU %user %nice %system %iowait %steal %idle 02:31:30 all 0.00 0.00 0.00 0.00 0.00 100.00 02:31:31 all 2.22 0.00 2.22 0.00 0.00 95.56 02:31:32 all 41.67 0.00 6.25 0.00 2.08 50.00 02:31:33 all 86.36 0.00 13.64 0.00 0.00 0.00 02:31:34 all 75.00 0.00 25.00 0.00 0.00 0.00 02:31:35 all 93.18 0.00 6.82 0.00 0.00 0.00 02:31:36 all 90.70 0.00 9.30 0.00 0.00 0.00 02:31:37 all 71.05 0.00 0.00 0.00 0.00 28.95 02:31:38 all 14.89 0.00 10.64 0.00 2.13 72.34 02:31:39 all 2.56 0.00 0.00 0.00 0.00 97.44 02:31:40 all 0.00 0.00 0.00 0.00 0.00 100.00 02:31:41 all 0.00 0.00 0.00 0.00 0.00 100.00 My suspicion that this comes from I/O related issue is also because a caching plugin I use to reduce the amount of queries to the database, by precompiling PHP pages is actually making things worse instead of better. It seems that file access is making things worse instead.

  Read the article

• USB mouse disconnecting and reconnecting randomly and often

  - by Marc

  Specs: Q6600, evga 780I sli mobo, 4gig RAM, logitech MX518, windows 7 64bit, evga gtx 260, 650W power supply (single rail) The problem I am having is my mouse will reconnect/disconnect (will even hear the sounds from windows) and the light on the bottom of the mouse will turn off/turn on as it starts working again. It really sucks to be playing a game (and happens on desktop as well) for the mouse to just die out for a few seconds and come back. Sometimes it will not happen for days and other times it will do it 2 or more times within 15 seconds. I have tried two different wired mice, have tried multiple USB ports (on front of computer, back of computer, have also used a USB hub and have also plugged in a card that connects to the USB connectors on the motherboard and adds a few usb ports to the back of the computer, and I also bought a USB 2.0 PCI card and that did not help). Nothing else seems to reconnect like this, my usb keyboard has never once cut out like the mouse does and neither have any of the other devices I have connected (webcam, usb hub, various devices sometimes connected through usb cables, and IR reciever for windows media center remote). I have disconnected all usb devices except for my keyboard and mouse and the problem still occurs. I guess it could be something wrong with my motherboard but since no other devices behave similarly I'm just hoping that it is some kind of driver conflict. Installing logitech's drivers has had no effect. It seemed at first that if I go to device manager and uninstall HID-compliant mouse (that and logitech mx518 are listed) that would fix it but it doesn't seem to work anymore or at least not every time (it keeps reinstalling). I have googled "usb mouse disconnects and reconnects" and it seems to be fairly common but none of those were resolved. To stick some easy steps: It happens with or without the drivers installed It has happened with multiple mice on the same computer Bios is the latest version (P08) Motherboard drivers are the latest version Device manager is listing no problems on any USB devices Happens with every usb port, even addon usb cards Happens when all usb devices aside from mouse and keyboard are unplugged I read that maybe it is an IRQ conflict and I tried to look into that but did not really know what was going on, but didn't see anything obviously wrong. Thanks for any help guys, its driving me crazy!

  Read the article

• How can I prevent an unintentional DDOS running ColdFusion 8 with IIS 6?

  - by Eric Belair

  We had an interesting outage today on one of our client's websites. Out of nowhere, the website was inaccessible. The website runs by itself on a dedicated physical Windows 2000 server (probably overkill, I know, but that's a discussion for a different day). After restarting IIS and ColdFusion Application Service, the problem came back several times. My initial thought was that it was a DNS issue, which happens occasionally - the last time it happened was after Hurricane Sandy when we our ISP was out, and we had to make some network config changes. But, it was not a DNS issue. My second thought was that it was a DDOS attack, but, there's very little reason anyone would want to take this site down. When we called our ISP, the operator on the other end noted that traffic was spiking significantly. As it turned out, the client had unintentionally caused a DDOS on the website, after they FTPed a very large video file, and then mass emailed a link to it. Hundreds of people clicked the link and brought the site to its knees. I am primarily a Website Programmer, but I often have to contribute to server administration at times. Sadly, I'm the resident ColdFusion and IIS expert, but I don't have a lot of experience with this issue. What are some basic steps that I can take to prevent this from happening in the future, since we cannot always control what files the client posts to the website. Here are some ideas I had, but I'm unsure of the impact: Limit the number of connections in IIS. Put media files on a separate server (like an Amazon site, etc.). File requests of this type currently behind a server-script (i.e. /www.site.com/viewFile.cfm?fileId=1424545, where the fileId references a file off the webroot) that logs requests, and pushes the file to the browser using CFCONTENT. I could edit this script to reject requests when they exceed a certain amount in a given time-frame (i.e. a 5MB can be accessed globally 10 times in an hour). This may cause some users frustration, but, if hundreds of users are attempting to view the file, the site is going to crash anyways, as it did today, which is way more frustrating, since there is no "pretty" message explaining why they can't get to the file. I'm open to any suggestions, as I'm continuing my research to report to the CTO with the best options, so that we can put a solution into effect. Thank you.

  Read the article

• keyboard mappings are totally screwed after updating to kde4

  - by zeonglow

  I recently upgraded from KDE 3.5 to KDE 4, and I have been having weird issues with my keyboard. In one of the virtual consoles e.g. when I press ctrl + alt 1 , I can type perfectly, but in KDE, several of the number keys don't work, the left and right arrows don't work either. When I press the right arrow key in xev I get this: KeyRelease event, serial 34, synthetic NO, window 0x3600001, root 0x6f, subw 0x0, time 903459, (111,55), root:(115,836), state 0x10, keycode 114 (keysym 0x1008ff11, XF86AudioLowerVolume), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False When I press the '3' key it toggles my Bookmarks toolbar in Firefox, in xev I get this: KeyPress event, serial 34, synthetic NO, window 0x3600001, root 0x6f, subw 0x0, time 999968, (94,115), root:(98,896), state 0x10, keycode 12 (keysym 0x1008ff30, XF86Favorites), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False KeyRelease event, serial 34, synthetic NO, window 0x3600001, root 0x6f, subw 0x0, time 1000032, (94,115), root:(98,896), state 0x10, keycode 12 (keysym 0x1008ff30, XF86Favorites), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False As this is deeper down, changing the type of keyboard in the KDE meun's has no effect. I'm slowly beginning to wade through the mountains of documentation about the X keyboard model, but there has to be a better way. Does anyone no what it is? Edit: 1234567890 ! after deleting the entire .kde folder. but only until I change the Keyboard settings from the "system settings" applet, then its hosed full time. Regardless of what I set the settings too. (restore to default settings doesn't) 2nd Edit: I'm using Gentoo AMD64, I was upgrading from KDE 3.5 KDE 4.2. I think I had manual settings before, although I didn't change anything. I was originally running KDE without HAL until that stop working a year or so ago. The only customisation I made was to set the multimedia keys to control Amarok. 3rd Edit $ grep xkb /var/log/Xorg.0.log (**) Option "xkb_rules" "evdev" (**) Option "xkb_model" "evdev" (**) Option "xkb_layout" "us" (**) Option "xkb_rules" "evdev" (**) Option "xkb_model" "evdev" (**) Option "xkb_layout" "us" Xorg.0.log has this to say: (WW) AllowEmptyInput is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled. (WW) Disabling Mouse1 (WW) Disabling Keyboard1 My Xorg.conf has this in it. Identifier "Keyboard1" Driver "kbd" Option "AutoRepeat" "500 30" # Specify which keyboard LEDs can be user-controlled (eg, with xset(1)) Option "XkbRules" "xorg" Option "XkbModel" "pc105" Option "XkbLayout" "gb"

  Read the article

• Windows: Impact of clean install Service Pack 2 to applications & data?

  - by Thomas Matthews

  My Windows Vista Home Premium system is corrupt and won't install Service Pack 2. I have followed all the advice from Microsoft and still no luck. I would like to perform a clean install of Vista, then SP1, and then SP2. My concern is the effect of the clean install on the registry, my apps and all my data. My plan: 1. Download Vista Service Pack 1 (SP1) ISO and write to DVD. 2. Download Vista Service Pack 2 (SP2) ISO and write to DVD. 3. Backup all data, applications and registry to external hard drive (file copy not disk image) 4. ?? Format hard drive?? (is this necessary?) 5. Install Vista from DVDs / CDs. 6. Install SP1 from DVD 7. Install SP2 from DVD 8. Restore registry, applications and data from external hard drive. My questions: 1. Is formatting the hard drive a necessary step? 2. Will restoring the registry from the backup corrupt the system? 3. Should I use Windows Backup or ZIP/RAR? 4. Any gotcha's that I should look out for? Background: I am using Windows Vista Home Premium with SP1. The sfc program does not finish due to a resources problem (even when run as administrator). I have 5 users on it. After a while, the screen goes black and shows an error message window about an error with login.scr. Standard accounts display a black screen and can't run any applications. Administrative accounts have no problems (even standard accounts when converted to Administrative have no problem). The CBS log contains a lot of 0x8000ffff and E_UNEXPECTED errors (which Microsoft defines as catastrophic failure). This is the reasoning behind performing a clean install up to service pack 2.

  Read the article

• Cannot exit X server, restart, shutdown or drop to tty when VGA monitor active

  - by terdon

  I have a strange problem. If I connect an external VGA monitor to my laptop, exiting the X environment in any way crashes the computer. For example, say I am working with my two monitors (the laptop's and one connected to my VGA port) active. Hitting Ctrl+Alt+F Key should take me down to a tty. What actually happens is that the VGA screen goes blank, as you would expect, but the laptop screen, although still on, shows nothing. I know the screen is on because it is slightly more illuminated than when it is off. When in this state, I can do nothing to regain access to the machine. I have tried: Ctrl+F Key (and even Ctrl+Alt+F Key, just in case) combinations and none seem to have any effect. Ctrl+Alt+Del : Nothing Magic SysRq key: Nothing Blindly typing my username and password and trying to reboot/shutdown or restart GDM or MDM: Nothing The only thing that works is a hard reset. The exact same behavior occurs when kiling the X server through Ctrl+Alt+Backspace, rebooting or shutdown. There is no difference if I reboot/shutdown/log out using the WM's graphical menu or if I use the shutdown or rebootcommands. It is also not WM-dependent. I have the same problem using Cinnamon, Gnome 3, MATE and xfce4. It is, however, VGA dependent. I have tried connecting another VGA monitor and have the same problem. I do not, however, have this problem if a screen is connected to the DisplayPort. It is, therefore, a VGA specific issue. To make things even stranger, this only occurs when both screens are active. If either the laptop screen or the VGA monitor is inactive the problem goes away. Finally, this problem arose when I installed the latest Linux Mint Debian (LMDE). It did not occur with the previous release of LMDE. I am not sure what has changed since I used the same kernel version in both releases (I had upgraded the kernel while on the previous release) and, I think, the same nvidia drivers. Oh, and yes, I have updated the nvidia driver. Hardware: Dell M4500 laptop CPU: Intel Core i7 RAM: 8GB Graphics: nVidia GT216 [Quadro FX 880M] Software: LMDE, kernel 3.2.0-2-amd64 Xorg: 1.11.4 nVidia kernel: 295.20-1+3.2.9-1 Possibly relevant files: /var/log/Xorg.0.log ~/.xsession-errors Does anyone have any ideas how to fix this? Thanks in advance for any help.

  Read the article

• Areca 1280ml RAID6 volume set failed

  - by Richard

  Today we hit some kind of worst case scenario and are open to any kind of good ideas. Here is our problem: We are using several dedicated storage servers to host our virtual machines. Before I continue, here are the specs: Dedicated Server Machine Areca 1280ml RAID controller, Firmware 1.49 12x Samsung 1TB HDDs We configured one RAID6-set with 10 discs that contains one logical volume. We have two hot spares in the system. Today one HDD failed. This happens from time to time, so we replaced it. Upon rebuilding a second disc failed. Normally this is no fun. We stopped heavy IO-operations to ensure a stable RAID rebuild. Sadly the hot-spare disc failed while rebuilding and the whole thing stopped. Now we have the following situation: The controller says that the raid set is rebuilding The controller says that the volume failed It is a RAID 6 system and two discs failed, so the data has to be intact, but we cannot bring the volume online again to access the data. While searching we found the following leads. I don't know whether they are good or bad: Mirroring all the discs to a second set of drives. So we would have the possibility to try different things without loosing more than we already have. Trying to rebuild the array in R-Studio. But we have no real experience with the software. Pulling all drives, rebooting the system, changing into the areca controller bios, reinserting the HDDs one-by-one. Some people are saying that the brought the system online by this. Some are saying that the effect is zero. Some say, that they blew the whole thing. Using undocumented areca commands like "rescue" or "LeVel2ReScUe". Contacting a computer forensics service. But whoa... primary estimates by phone exceeded 20.000€. That's why we would kindly ask for help. Maybe we are missing the obvious? And yes of course, we have backups. But some systems lost one week of data, thats why we'd like to get the system up and running again. Any help, suggestions and questions are more than welcome.

  Read the article

• My computer's dying :(

  - by j-t-s

  Hi All I have a sweet computer and have never had any real problems with it until now. I recently formatted my computer and all was well. But now my monitor randomly flickers. The monitor will just go black for about a second or two, then it'll return back to its normal state with all the stuff still on the screen. This is getting progressively worse. Another problem that has started is my computer randomly restarts. (I've managed to prevent it from restarting by removing the check in Automatically Restart from the Startup and Recovery Dialog. But I know this doesn't solve the problem). It also completely freezes up on me. One last thing, this morning I got a big blue screen. I can't remember what it said, but if it happens again I will take note of it and repost. Or if I can find some kind of a log file containing that bluescreen error I will post. I have checked all cords, and they're all fine. Nothing's loose. My computer isn't overheating either. I've taken the case off for 3 whole days and haven't used the computer for those 3 days, which has had no effect. I've checked the connections inside and nothing's loose there either. I know there's nothing wrong with my monitor because my friend has 2 computers and it works perfectly on those computers. I don't understand how my computer could suddenly become so unstable. I'm almost certain that I have no viruses; I full-scan my pc everyday for nastys, and have strict firewall settings. Anyway, I don't see how it could be a virus anyway simply due to the fact that I had these problems right after I formatted, and before I even had the chance to install or copy anything or even connect to the internet. I know it has nothing to do with the way I formatted the computer too, I've been fixing computers for years. Sorry for rambling on, just making sure I don't leave anything out. Has anybody else had this problem? Can somebody please try to help me with this? Thank you :)

  Read the article

• Force Finder to log in as Guest to a SMB share

  - by slhck

  I have a QNAP NAS that offers a few SMB shares. As I'm in a trusted environment, my shares are accessible as guest rather than with a combination of username and password. Problem Now, when I click the name of the device in Finder's sidebar, I get the black "Connection failed" bar, with the option "Connect as...". When I click that, I receive: I can however press ? + K and enter the server's name manually, which gets me to this window: Here, I have to select "guest". Now, I can select one of the shares to connect to, and I'm finally connected to the server. If I select it in the sidebar, I get a list of all shares available, because I'm connected as "guest", obviously: What I need Well, as soon as I unmount all shares, I have to go through the same procedure of manually logging in as "guest" again, which I find quite annoying. Is there any way I could get Finder (or the underlying SMB client) to know which credentials to use? Or should I look for the solution rather on the server side? (I know that other SMB shares seem to work fine in my network) Diagnostics The only thing I can get out of Console.app is: 5/15/11 7:36:40 PM /System/Library/CoreServices/Finder.app/Contents/MacOS/Finder[200] SharePointBrowser::handleOpenCallBack returned 64 This message occurs when I click the name of the SMB server in the Finder sidebar. Here's the output of `smbclient -L meredith -U guest -d=2 charon:~ werner$ smbclient -L meredith -U guest -d=2 added interface ip=192.168.100.11 bcast=192.168.100.255 nmask=255.255.255.0 tdb(unnamed): tdb_open_ex: could not open file /private/var/samba/gencache.tdb: Permission denied Got a positive name query response from 192.168.100.100 ( 192.168.100.100 ) Password: Domain=[MEREDITH] OS=[Unix] Server=[Samba 3.5.2] Sharename Type Comment --------- ---- ------- music Disk movies Disk photos Disk software Disk archive Disk backups Disk IPC$ IPC IPC Service (NAS Server) Got a positive name query response from 192.168.100.100 ( 192.168.100.100 ) Domain=[MEREDITH] OS=[Unix] Server=[Samba 3.5.2] Server Comment --------- ------- Workgroup Master --------- ------- WORKGROUP MEREDITH Also, things I've tried: There is no relevant entry in the Keychain (but why would it, I'm only connecting as guest) Connecting with user name "Guest" and empty password logs me in but still after ejecting the last share, I get the same "Connection failed" error as before. The appropriate entry is made in the Keychain but obviously has no effect.

  Read the article

< Previous Page | 237 238 239 240 241 242 243 244 245 246 247 248  | Next Page >