Search Results

Search found 6395 results on 256 pages for 'weird behaviour'.

Page 242/256 | < Previous Page | 238 239 240 241 242 243 244 245 246 247 248 249  | Next Page >

  • PC: Quick Freeze, then BSOD, then forced reboot, then freezes again

    - by cr0z3r
    Lately I have been experiencing a weird issue. My PC will hang for a second and then BSOD - it stays there, so I have to reboot. Once Windows starts again and I'm logged in, after 1-10min it freezes again, this time without BSOD. RECAP: 1 second freeze BSOD, hangs there I have to force-reboot Once PC rebooted, I log back into Windows second freeze between a 1-10min range, no BSOD (alternatively, I get a freeze with a constant sound/noise, no BSOD) I contacted my PC provider, who told me my graphics-card might be flawed (Quadro 4000), so I used a Quadro 2000 that they lend me. The issue still occurred. The issue now seemed to belong to a flawed RAM module. Following my provider's steps, I removed all but the first from the left column and kept using my PC for a week or so without any issues. I then added the bottom-right module, and so on, until all modules were back inside - I had no problems. Now it seemed that a simple take-out-put-back-in of the RAM modules had fixed the issue. However, after a few months, the issue was back. I redid all the RAM-swapping I had done before, and concluded that the lower-right module was flawed. My provider changed it for another, and everything was great until now. My PC froze again for barely a second, hanged on a BSOD, I rebooted it, logged-in to Windows to get a freeze (without BSOD or reboot) 40 seconds later. Something worth noting, is that every time I reboot after the BSOD, it is something within Chrome that freezes my PC (e.g. this time I clicked the "restore" button as Chrome mentioned it had exited unexpectedly - from the previous freeze obviously - and it instantly froze). Finally, the Event Viewer lists 2 critical events in the past hour as "ID: 41, Type: Kernel-Power". PC-Specs: http://i.imgur.com/VZpbr.jpg Previous Dump-files: https://dl.dropbox.com/u/716600/DumpFiles_08_2012.zip I would like to thank anybody in advance for your help. You're great. UPDATE 1: I realized that I did not mention an awkward fact about this issue. After I have gotten the 1-sec freeze followed by a BSOD, after I rebooted because the BSOD hanged, and after I logged back in to get another (this time, eternal) freeze and rebooted once again, the PC does not boot back up. The power-light is on, but my monitor says "no signal", as if the PC wouldn't really be turned on. This truly seems a like a power-related issue, doesn't it? UPDATE 2: I just got a freeze, but without BSOD. My screen froze (while on Chrome, which is starting to seem suspicious to me) with an ongoing sound/noise. I had to force-reboot my PC. I would say this is a graphics-card issue, but this issue also happened when I was using the Quadro 2000 from my provider. UPDATE 3: I just got a BSOD while trying to render something (quite heavy, actually) in 3ds Max 2012. I left the BSOD "running", as it said it was writing dump files to disk. However, the percentage number stayed at 0, so after 15 minutes I force-rebooted. I then used the software WhoCrashed (thank you Dave) which reported the following from the C:\Windows\Memory.dmp file: On Thu 22.11.2012 22:13:45 GMT your computer crashed crash dump file: C:\Windows\memory.dmp uptime: 01:05:27 This was probably caused by the following module: Unknown () Bugcheck code: 0x124 (0x0, 0xFFFFFA80275AC028, 0xF200001F, 0x100B2) Error: WHEA_UNCORRECTABLE_ERROR Bug check description: This bug check indicates that a fatal hardware error has occurred. This bug check uses the error data that is provided by the Windows Hardware Error Architecture (WHEA). This is likely to be caused by a hardware problem problem. This problem might be caused by a thermal issue. A third party driver was identified as the probable root cause of this system error. It is suggested you look for an update for the following driver: Unknown . Google query: Unknown WHEA_UNCORRECTABLE_ERROR

    Read the article

  • Apache doesn't run multiple requests

    - by Reinderien
    I'm currently running this simple Python CGI script to test rudimentary IPC: #!/usr/bin/python -u import cgi, errno, fcntl, os, os.path, sys, time print("""Content-Type: text/html; charset=utf-8 <!doctype html> <html lang="en"> <head> <meta charset="utf-8" /> <title>IPC test</title> </head> <body> """) ftempname = '/tmp/ipc-messages' master = not os.path.exists(ftempname) if master: fmode = 'w' else: fmode = 'r' print('<p>Opening file</p>') sys.stdout.flush() ftemp = open(ftempname, fmode) print('<p>File opened</p>') if master: print('<p>Operating as master</p>') sys.stdout.flush() for i in range(10): print('<p>' + str(i) + '</p>') sys.stdout.flush() time.sleep(1) ftemp.close() os.remove(ftempname) else: print('<p>Operating as a slave</p>') ftemp.close() print(""" </body> </html>""") The 'server-push' portion works; that is, for the first request, I do see piecewise updates. However, while the first request is being serviced, subsequent requests are not started, only to be started after the first request has finished. Any ideas on why, and how to fix it? Edit: I see the same non-concurrent behaviour with vanilla PHP, running this: <!doctype html> <html lang="en"> <!-- $Id: $--> <head> <meta charset="utf-8" /> <title>IPC test</title> </head> <body> <p> <?php function echofl($str) { echo $str . "</b>\n"; ob_flush(); flush(); } define('tempfn', '/tmp/emailsync'); if (file_exists(tempfn)) $perms = 'r+'; else $perms = 'w'; assert($fsync = fopen(tempfn, $perms)); assert(chmod(tempfn, 0600)); if (!flock($fsync, LOCK_EX | LOCK_NB, $wouldblock)) { assert($wouldblock); $master = false; } else $master = true; if ($master) { echofl('Running as master.'); assert(fwrite($fsync, 'content') != false); assert(sleep(5) == 0); assert(flock($fsync, LOCK_UN)); } else { echofl('Running as slave.'); echofl(fgets($fsync)); } assert(fclose($fsync)); echofl('Done.'); ?> </p> </body> </html>

    Read the article

  • GNU/Linux swapping blocks system

    - by Ole Tange
    I have used GNU/Linux on systems from 4 MB RAM to 512 GB RAM. When they start swapping, most of the time you can still log in and kill off the offending process - you just have to be 100-1000 times more patient. On my new 32 GB system that has changed: It blocks when it starts swapping. Sometimes with full disk activity but other times with no disk activity. To examine what might be the issue I have written this program. The idea is: 1 grab 3% of the memory free right now 2 if that caused swap to increase: stop 3 keep the chunk used for 30 seconds by forking off 4 goto 1 - #!/usr/bin/perl sub freekb { my $free = `free|grep buffers/cache`; my @a=split / +/,$free; return $a[3]; } sub swapkb { my $swap = `free|grep Swap:`; my @a=split / +/,$swap; return $a[2]; } my $swap = swapkb(); my $lastswap = $swap; my $free; while($lastswap >= $swap) { print "$swap $free"; $lastswap = $swap; $swap = swapkb(); $free = freekb(); my $used_mem = "x"x(1024 * $free * 0.03); if(not fork()) { sleep 30; exit(); } } print "Swap increased $swap $lastswap\n"; Running the program forever ought to keep the system at the limit of swapping, but only grabbing a minimal amount of swap and do that very slowly (i.e. a few MB at a time at most). If I run: forever free | stdbuf -o0 timestamp > freelog I ought to see swap slowly rising every second. (forever and timestamp from https://github.com/ole-tange/tangetools). But that is not the behaviour I see: I see swap increasing in jumps and that the system is completely blocked during these jumps. Here the system is blocked for 30 seconds with the swap usage increases with 1 GB: secs 169.527 Swap: 18440184 154184 18286000 170.531 Swap: 18440184 154184 18286000 200.630 Swap: 18440184 1134240 17305944 210.259 Swap: 18440184 1076228 17363956 Blocked: 21 secs. Swap increase 2400 MB: 307.773 Swap: 18440184 581324 17858860 308.799 Swap: 18440184 597676 17842508 330.103 Swap: 18440184 2503020 15937164 331.106 Swap: 18440184 2502936 15937248 Blocked: 20 secs. Swap increase 2200 MB: 751.283 Swap: 18440184 885288 17554896 752.286 Swap: 18440184 911676 17528508 772.331 Swap: 18440184 3193532 15246652 773.333 Swap: 18440184 1404540 17035644 Blocked: 37 secs. Swap increase 2400 MB: 904.068 Swap: 18440184 613108 17827076 905.072 Swap: 18440184 610368 17829816 942.424 Swap: 18440184 3014668 15425516 942.610 Swap: 18440184 2073580 16366604 This is bad enough, but what is even worse is that the system sometimes stops responding at all - even if I wait for hours. I have the feeling it is related to the swapping issue, but I cannot tell for sure. My first idea was to tweak /proc/sys/vm/swappiness from 60 to 0 or 100, just to see if that had any effect at all. 0 did not have an effect, but 100 did cause the problem to arise less often. How can I prevent the system from blocking for such a long time? Why does it decide to swapout 1-3 GB when less than 10 MB would suffice?

    Read the article

  • BSOD & System Failure after trying to install a new RAM

    - by Praveen Kumar
    I have updated the question with sections, so that people won't find it difficult to read. Basic System Information Let me give a basic introduction on my system. I have a system of following configuration: Processor: Intel(R) Core(TM) i7-2600 CPU @ 3.40GHz 3.40GHz RAM: Corsair Vengeance - 4GB Single Module DDR3 Memory Kit (CMZ4GX3M1A1600C9) x 2 OS: Windows 7 Ultimate, SP1 Build 7601 HDD: 1 TB Seagate 7200 RPM The Problem It was working fine for about an year. Yesterday I planned to increase my RAM to 16 GB by putting another set of two Corsair Vengeance - 4GB Single Module DDR3 Memory Kit (CMZ4GX3M1A1600C9). I got it from an authorized reseller and also, the RAM was fitted by a service engineer only. After the RAM was fit (all the four), the system failed to start, with an error code of 0x000000f4. The complete information of it is: Problem signature: Problem Event Name: BlueScreen OS Version: 6.1.7601.2.1.0.256.1 Locale ID: 16393 Additional information about the problem: BCCode: f4 BCP1: 0000000000000003 BCP2: FFFFFA8008A39060 BCP3: FFFFFA8008A39340 BCP4: FFFFF800037C8510 OS Version: 6_1_7601 Service Pack: 1_0 Product: 256_1 Files that help describe the problem: C:\Windows\Minidump\093012-13041-01.dmp C:\Users\Praveen Kumar\AppData\Local\Temp\WER-30716-0.sysdata.xml Read our privacy statement online: http://go.microsoft.com/fwlink/?linkid=104288&clcid=0x0409 If the online privacy statement is not available, please read our privacy statement offline: C:\Windows\system32\en-US\erofflps.txt Another Problem We first thought that it was the RAM, which caused the issue. So I returned the RAMs and now my computer configuration is exactly how it was the previous day. But, following the removal of the RAM, I also had several crashes after that. One suspicious thing was with an error code c0000134: STOP: c0000135 The program can’t start because %hs is missing from your computer . Try resintalling the program to fix this problem. After reading contents from this, this and this, which were never my case, they didn't help me. But I didn't receive any more STOP c0000134 messages. But this 0x000000f4 keeps on coming. I am writing from the same system and it allows me to work for say, half an hour max. Then I hear a device disconnect sound, the one you hear in Windows 7, when a USB Mass Storage Device is plugged out. Immediately following that, my screen goes blank and I get 0x000000f4 blue screen. Okay, now I am really concerned about my Hard Disk data, but I have no clue if there is a problem with the HDD. My Question What all files do I need to submit for your reference? Can this issue be fixed? I am getting more time if I remove my RAM, clean it and then put it back. Weird! Hope I have given the necessary information to help you guys. Thanks in advance. Minidumps I have uploaded all the Minidump DMP files from C:\Windows\Minidump folder here: http://www.praveen-kumar.com/Minidumps.zip Let me know if you face any issues in accessing it. Will be able to share elsewhere. Updates 30-Sep-2012 10:15 AM IST: When I keep the system cover opened, pressed the HDD Cable well, it is allowing me to be on for about half an hour, I guess? Also, I feel that the CPU fan speed is kind of slow. It rotates at around 900 RPM, but the CPU Temperature is not more than 70° C. 30-Sep-2012 10:30 AM IST: My Modem (Beetel 220BX ADSL2+ Router) failed. I have no idea how it is related to this issue, but I thought that I need to document this too. I really have a bad day here. 30-Sep-2012 11:00 AM IST: System still running fine, with the cabinet cover open, now for about an hour. 30-Sep-2012 12:00 PM IST: I shut down the system and closed the cabinet. Started the system, and it hung after giving the password. After a few minutes, got the same 0x000000f4 error. So, while it is in the upright position, fixed the Hard Disk cable and now it is booting fine. Waiting for more observations and answers.

    Read the article

  • wireless internet in linux is very very slow... but in windows.... everythnings fine

    - by Cody Acer
    yesterday when i was connecting to our neighbors wifi connection which is the signal strength is below 50%, i cant browse anything... even ping to gateway. 100% packet loss, and sometimes.. i can connect awesomely i can open my facebook account for 15 minutes but after 15min.. connection is extremely slow. but not windows i can surf even the signal str is very poor weird ey??.. root@Emely:~# lspci -knn 00:00.0 Host bridge [0600]: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx DMI Bridge [8086:a010] Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller [0300]: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx Integrated Graphics Controller [8086:a011] Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: i915 Kernel modules: i915 00:02.1 Display controller [0380]: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx Integrated Graphics Controller [8086:a012] Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] 00:1b.0 Audio device [0403]: Intel Corporation NM10/ICH7 Family High Definition Audio Controller [8086:27d8] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 1 [8086:27d0] (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 2 [8086:27d2] (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.2 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 3 [8086:27d4] (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 4 [8086:27d6] (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: uhci_hcd 00:1d.1 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: uhci_hcd 00:1d.2 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: uhci_hcd 00:1d.3 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 [8086:27cb] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: uhci_hcd 00:1d.7 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller [8086:27cc] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: ehci-pci 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) 00:1f.0 ISA bridge [0601]: Intel Corporation NM10 Family LPC Controller [8086:27bc] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: lpc_ich Kernel modules: lpc_ich 00:1f.2 SATA controller [0106]: Intel Corporation NM10/ICH7 Family SATA Controller [AHCI mode] [8086:27c1] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: ahci Kernel modules: ahci 00:1f.3 SMBus [0c05]: Intel Corporation NM10/ICH7 Family SMBus Controller [8086:27da] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel modules: i2c-i801 05:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter [14e4:4727] (rev 01) Subsystem: Wistron NeWeb Corp. Device [185f:051a] Kernel driver in use: bcma-pci-bridge Kernel modules: bcma 09:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller [11ab:4354] Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: sky2 Kernel modules: sky2 root@Emely:~# ip addr show 1: lo: mtu 65536 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: mtu 1500 qdisc pfifo_fast state DOWN qlen 1000 link/ether e8:11:32:2e:a6:fd brd ff:ff:ff:ff:ff:ff 3: wlan0: mtu 1500 qdisc mq state UP qlen 1000 link/ether 00:1b:b1:a9:ac:e0 brd ff:ff:ff:ff:ff:ff inet 192.168.1.108/24 brd 192.168.1.255 scope global wlan0 inet6 fe80::21b:b1ff:fea9:ace0/64 scope link valid_lft forever preferred_lft forever root@Emely:~# ip link show 1: lo: mtu 65536 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 2: eth0: mtu 1500 qdisc pfifo_fast state DOWN qlen 1000 link/ether e8:11:32:2e:a6:fd brd ff:ff:ff:ff:ff:ff 3: wlan0: mtu 1500 qdisc mq state UP qlen 1000 link/ether 00:1b:b1:a9:ac:e0 brd ff:ff:ff:ff:ff:ff root@Emely:~# rfkill list all 0: samsung-wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: samsung-bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: hci0: Bluetooth Soft blocked: no Hard blocked: no 3: phy0: Wireless LAN Soft blocked: no Hard blocked: no is this a wireless driver issue?

    Read the article

  • How to prevent delays associated with IPv6 AAAA records?

    - by Nic
    Our Windows servers are registering IPv6 AAAA records with our Windows DNS servers. However, we don't have IPv6 routing enabled on our network, so this frequently causes stall behaviours. Microsoft RDP is the worst offender. When connecting to a server that has a AAAA record in DNS, the remote desktop client will try IPv6 first, and won't fall back to IPv4 until the connection times out. Power users can work around this by connecting to the IP address directly. Resolving the IPv4 address with ping -4 hostname.foo always works instantly. What can I do to avoid this delay? Disable IPv6 on client? Nope, Microsoft says IPv6 is a mandatory part of the Windows operating system. Too many clients to ensure this is set everywhere consistently. Will cause more problems later when we finally implement IPv6. Disable IPv6 on the server? Nope, Microsoft says IPv6 is a mandatory part of the Windows operating system. Requires an inconvenient registry hack to disable the entire IPv6 stack. Ensuring this is correctly set on all servers is inconvenient. Will cause more problems later when we finally implement IPv6. Mask IPv6 records on the user-facnig DNS recursor? Nope, we're using NLNet Unbound and it doesn't support that. Prevent registration of IPv6 AAAA records on the Microsoft DNS server? I don't think that's even possible. At this point, I'm considering writing a script that purges all AAAA records from our DNS zones. Please, help me find a better way. UPDATE: DNS resolution is not the problem. As @joeqwerty points out in his answer, the DNS records are returned instantly. Both A and AAAA records are immediately available. The problem is that some clients (mstsc.exe) will preferentially attempt a connection over IPv6, and take a while to fall back to IPv4. This seems like a routing problem. The ping command produces a "General failure" error message because the destination address is unroutable. C:\Windows\system32>ping myhost.mydomain Pinging myhost.mydomain [2002:1234:1234::1234:1234] with 32 bytes of data: General failure. General failure. General failure. General failure. Ping statistics for 2002:1234:1234::1234:1234: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), I can't get a packet capture of this behaviour. Running this (failing) ping command does not produce any packets in Microsoft Network Monitor. Similarly, attempting a connection with mstsc.exe to a host with an AAAA record produces no traffic until it does a fallback to IPv4. UPDATE: Our hosts are all using publicly-routable IPv4 addresses. I think this problem might come down to a broken 6to4 configuration. 6to4 behaves differently on hosts with public IP addresses vs RFC1918 addresses. UPDATE: There is definitely something fishy with 6to4 on my network. When I disable 6to4 on the Windows client, connections resolve instantly. netsh int ipv6 6to4 set state disabled But as @joeqwerty says, this only masks the problem. I'm still trying to find out why IPv6 communication on our network is completely non-working.

    Read the article

  • Linux bcm43224 wifi adapter slows down a couple minutes after boot

    - by Blubber
    I just installed Ubuntu on my mid 2012 MacBook Air. Everything worked out of the box, but the wifi is showing some weird behavior. When I first login it's really fast, loading google.com is near instant, and browsing in general feels at least as smooth as it did on Mac OS. However, after a couple minutes the connection slows down dramatically, sometimes it takes over 5s to load google.com, a simple reboot fixes the problem for another couple minutes. Specs: Wifi: 02:00.0 Network controller: Broadcom Corporation BCM43224 802.11a/b/g/n (rev 01) Driver: open-source brcmsmac driver Kernel: Linux wega 3.8.0-21-generic #32-Ubuntu SMP Tue May 14 22:16:46 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux Distro: Ubuntu 13.04 (uptodate) I tried a number of things, none of which actually helped Use proprietary sta driver from broadcom Installed firmware into /lib/firmware/brcms (which, as far as I can tell from logs, does not get loaded at all) Switch router to only use 2.4 OR 5 GHz Set router to only use a OR g OR n Set router to use AES encryption only Turned off power management on the adapter Set regulatory region to the correct value (NL) on both router and laptop Disable ipv6 Nothing seems to help, the slowdown always occurs. I did notice that the latency (ping google.com) stays roughly the same (around 9ms). Below is some more information that might be of use. $ lspci -nnk | grep -iA2 net 02:00.0 Network controller [0280]: Broadcom Corporation BCM43224 802.11a/b/g/n [14e4:4353] (rev 01) Subsystem: Apple Inc. Device [106b:00e9] Kernel driver in use: bcma-pci-bridge $ rfkill list 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no $ lsmod Module Size Used by dm_crypt 22820 1 arc4 12615 2 brcmsmac 550698 0 coretemp 13355 0 kvm_intel 132891 0 parport_pc 28152 0 kvm 443165 1 kvm_intel ppdev 17073 0 cordic 12574 1 brcmsmac brcmutil 14755 1 brcmsmac mac80211 606457 1 brcmsmac cfg80211 510937 2 brcmsmac,mac80211 bnep 18036 2 rfcomm 42641 12 joydev 17377 0 applesmc 19353 0 input_polldev 13896 1 applesmc snd_hda_codec_hdmi 36913 1 microcode 22881 0 snd_hda_codec_cirrus 23829 1 nls_iso8859_1 12713 1 uvcvideo 80847 0 btusb 22474 0 snd_hda_intel 39619 3 videobuf2_vmalloc 13056 1 uvcvideo snd_hda_codec 136453 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec_cirrus bcm5974 17347 0 bluetooth 228619 22 bnep,btusb,rfcomm snd_hwdep 13602 1 snd_hda_codec lpc_ich 17061 0 videobuf2_memops 13202 1 videobuf2_vmalloc videobuf2_core 40513 1 uvcvideo videodev 129260 2 uvcvideo,videobuf2_core bcma 41051 1 brcmsmac snd_pcm 97451 3 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel snd_page_alloc 18710 2 snd_pcm,snd_hda_intel snd_seq_midi 13324 0 snd_seq_midi_event 14899 1 snd_seq_midi snd_rawmidi 30180 1 snd_seq_midi snd_seq 61554 2 snd_seq_midi_event,snd_seq_midi snd_seq_device 14497 3 snd_seq,snd_rawmidi,snd_seq_midi snd_timer 29425 2 snd_pcm,snd_seq snd 68876 16 snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_seq_device,snd_hda_codec_cirrus mei 41158 0 soundcore 12680 1 snd apple_bl 13673 0 mac_hid 13205 0 lp 17759 0 parport 46345 3 lp,ppdev,parport_pc usb_storage 57204 0 hid_apple 13237 0 hid_generic 12540 0 ghash_clmulni_intel 13259 0 aesni_intel 55399 399 aes_x86_64 17255 1 aesni_intel xts 12885 1 aesni_intel lrw 13257 1 aesni_intel gf128mul 14951 2 lrw,xts ablk_helper 13597 1 aesni_intel cryptd 20373 4 ghash_clmulni_intel,aesni_intel,ablk_helper i915 600351 3 ahci 25731 3 libahci 31364 1 ahci video 19390 1 i915 i2c_algo_bit 13413 1 i915 drm_kms_helper 49394 1 i915 usbhid 47074 0 drm 286313 4 i915,drm_kms_helper hid 101002 3 hid_generic,usbhid,hid_apple $ dmesg | egrep 'b43|bcma|brcm|[F]irm' [ 0.055025] [Firmware Bug]: ioapic 2 has no mapping iommu, interrupt remapping will be disabled [ 0.152336] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored [ 2.187681] pci_root PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-99] only partially covers this bridge [ 12.553600] bcma-pci-bridge 0000:02:00.0: enabling device (0000 -> 0002) [ 12.553657] bcma: bus0: Found chip with id 0xA8D8, rev 0x01 and package 0x08 [ 12.553688] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0) [ 12.553715] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0) [ 12.553764] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0) [ 12.605777] bcma: bus0: Bus registered [ 12.852925] brcmsmac bcma0:0: mfg 4bf core 812 rev 23 class 0 irq 17 [ 13.085176] brcmsmac bcma0:0: brcms_ops_bss_info_changed: qos enabled: false (implement) [ 13.085186] brcmsmac bcma0:0: brcms_ops_config: change power-save mode: false (implement) [ 20.862617] brcmsmac bcma0:0: brcmsmac: brcms_ops_bss_info_changed: associated [ 20.862622] brcmsmac bcma0:0: brcms_ops_bss_info_changed: arp filtering: enabled true, count 0 (implement) [ 20.862625] brcmsmac bcma0:0: brcms_ops_bss_info_changed: qos enabled: true (implement) [ 20.897957] brcmsmac bcma0:0: brcms_ops_bss_info_changed: arp filtering: enabled true, count 1 (implement) $ iwconfig lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"wlan" Mode:Managed Frequency:5.22 GHz Access Point: E0:46:9A:4E:63:9A Bit Rate=65 Mb/s Tx-Power=17 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=63/70 Signal level=-47 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:13 Invalid misc:56 Missed beacon:0

    Read the article

  • Ubuntu 10.04: OpenVZ Kernel and pure-ftpd issues on HOST (no guest setup yet)

    - by Seidr
    After compiling and installing the OpenVZ flavour of kernel under Ubuntu 10.04, I am unable to browse to certain directories when connecting to the pure-ftpd server. The clients are dropping into PASSIVE mode, which is fine. This behaviour was happening before the change of kernel, however now when I browse to certain directories the connection just gets dropped. This only happens with a few directories under one login (web in specific), where as with another login it happens as soon as I connect. I've got the nf_conntrack_ftp kernel module installed (required to keep track of passive FTP connections as I understand, and an alias of the ip_conntrack_ftp module), however this has provided no alleviation of my problem. This module was actually required upon initial setup of my OS to get passive FTP working correctly, however when I compiled the OpenVZ kernel a lot of these modules were missing (iptables, conntrack etc). I recompiled the kernel with the missing modules, but to no effect. I've turned verbosity for the pure-ftpd server up, and still no clues have been spotted in either syslog or the transfer log. Neither did an strace provide any clues (that I could discern anyway) - although one strange thing is both in the output to the client and in the strace I notice that it does infact probe the directory and return the number of matches - it just fails after that. One more thing to mention is that if I FTP using the same credentials locally, everything works fine. This suggests that it is in fact an issue with either the conntrack_ftp module not functioning as expected, or a deeper networking issue. The Kernel was compiled and installed following the instructions at https://help.ubuntu.com/community/OpenVZ - bar the changes to the Kernel configuration (such as add iptables as a module). Below is an example of the log sent to the data (under FileZilla). Status: Resolving address of xxxx.co.uk Status: Connecting to 78.46.xxx.xxx:21... Status: Connection established, waiting for welcome message... Response: 220---------- Welcome to Pure-FTPd [privsep] [TLS] ---------- Response: 220-You are user number 4 of 10 allowed. Response: 220-Local time is now 08:52. Server port: 21. Response: 220-This is a private system - No anonymous login Response: 220-IPv6 connections are also welcome on this server. Response: 220 You will be disconnected after 15 minutes of inactivity. Command: USER xxx Response: 331 User xxx OK. Password required Command: PASS ******** Response: 230-User xxx has group access to: client1 sshusers Response: 230 OK. Current restricted directory is / Command: OPTS UTF8 ON Response: 200 OK, UTF-8 enabled Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is your current location Status: Directory listing successful Status: Retrieving directory listing... Command: CWD /web Response: 250 OK. Current directory is /web Command: TYPE I Response: 200 TYPE is now 8-bit binary Command: PORT 10,0,2,30,14,143 Response: 500 I won't open a connection to 10.0.2.30 (only to 188.220.xxx.xxx) Command: PASV Response: 227 Entering Passive Mode (78,46,79,147,234,110) Command: MLSD Response: 150 Accepted data connection Response: 226-ASCII Response: 226-Options: -a -l Response: 226 57 matches total Error: Could not read from transfer socket: ECONNRESET - Connection reset by peer Error: Failed to retrieve directory listing Any suggestions please? I'm willing to try anything!

    Read the article

  • Auth-Type :- Reject in RADIUS users file matches inner tunnel request but sends Access-Accept

    - by mgorven
    I have WPA2 802.11x EAP authentication setup using FreeRADIUS 2.1.8 on Ubuntu 10.04.4 talking to OpenLDAP, and can successfully authenticate using PEAP/MSCHAPv2, TTLS/MSCHAPv2 and TTLS/PAP (both via the AP and using eapol_test). I am now trying to restrict access to specific SSIDs based on the LDAP groups which the user belongs to. I have configured group membership checking in /etc/freeradius/modules/ldap like so: groupname_attribute = cn groupmembership_filter = "(|(&(objectClass=posixGroup)(memberUid=%{User-Name}))(&(objectClass=posixGroup)(uniquemember=%{User-Name})))" and I have configured extraction of the SSID from Called-Station-Id into Called-Station-SSID based on the Mac Auth wiki page. In /etc/freeradius/eap.conf I have enabled copying attributes from the outer tunnel into the inner tunnel, and usage of the inner tunnel response in the outer tunnel (for both PEAP and TTLS). I had the same behaviour before changing these options however. copy_request_to_tunnel = yes use_tunneled_reply = yes I'm running eapol_test like this to test the setup: eapol_test -c peap-mschapv2.conf -a 172.16.0.16 -s testing123 -N 30:s:01-23-45-67-89-01:Example-EAP with the following peap-mschapv2.conf file: network={ ssid="Example-EAP" key_mgmt=WPA-EAP eap=PEAP identity="mgorven" anonymous_identity="anonymous" password="foobar" phase2="autheap=MSCHAPV2" } With the following in /etc/freeradius/users: DEFAULT Ldap-Group == "employees" and running freeradius-Xx, I can see that the LDAP group retrieval works, and that the SSID is extracted. Debug: [ldap] performing search in dc=example,dc=com, with filter (&(cn=employees)(|(&(objectClass=posixGroup)(memberUid=mgorven))(&(objectClass=posixGroup)(uniquemember=mgorven)))) Debug: rlm_ldap::ldap_groupcmp: User found in group employees ... Info: expand: %{7} -> Example-EAP Next I try to only allow access to users in the employees group (regardless of SSID), so I put the following in /etc/freeradius/users: DEFAULT Ldap-Group == "employees" DEFAULT Auth-Type := Reject But this immediately rejects the Access-Request in the outer tunnel because the anonymous user is not in the employees group. So I modify it to only match inner tunnel requests like so: DEFAULT Ldap-Group == "employees" DEFAULT FreeRADIUS-Proxied-To == "127.0.0.1" Auth-Type := Reject, Reply-Message = "User does not belong to any groups which may access this SSID." Now users which are in the employees group are authenticated, but so are users which are not in the employees group. I see the reject entry being matched, and the Reply-Message is set, but the client receives an Access-Accept. Debug: rlm_ldap::ldap_groupcmp: Group employees not found or user is not a member. Info: [files] users: Matched entry DEFAULT at line 209 Info: ++[files] returns ok ... Auth: Login OK: [mgorven] (from client test port 0 cli 02-00-00-00-00-01 via TLS tunnel) Info: WARNING: Empty section. Using default return values. ... Info: [peap] Got tunneled reply code 2 Auth-Type := Reject Reply-Message = "User does not belong to any groups which may access this SSID." ... Info: [peap] Got tunneled reply RADIUS code 2 Auth-Type := Reject Reply-Message = "User does not belong to any groups which may access this SSID." ... Info: [peap] Tunneled authentication was successful. Info: [peap] SUCCESS Info: [peap] Saving tunneled attributes for later ... Sending Access-Accept of id 11 to 172.16.2.44 port 60746 Reply-Message = "User does not belong to any groups which may access this SSID." User-Name = "mgorven" and eapol_test reports: RADIUS message: code=2 (Access-Accept) identifier=11 length=233 Attribute 18 (Reply-Message) length=64 Value: 'User does not belong to any groups which may access this SSID.' Attribute 1 (User-Name) length=9 Value: 'mgorven' ... SUCCESS Why isn't the request being rejected, and is this the right way to implement this?

    Read the article

  • Moved DNS and Email Hosting, Now Can't Send/Receive To/From Domains Hosted on Previous Host

    - by maxfinis
    Our company had 4 domains whose emails and DNS were hosted by one company, and then we moved the email and DNS hosting for 3 of the 4 domains to a new company. Now, the 3 domains that were moved can't send or receive emails to and from the one domain still left on the old server. All other email functions work fine for all 4 domains. There are no bouncebacks, error messages, or emails stuck in queue, and no evidence of these missing emails hitting the new servers. The new hosting company confirms that everything is fine on their end, and assures me that it's most likely an old zone file still remaining on the old nameserver, and so the emails sent from the old host is routed to what it believes is still the authoritative nameserver. Because the old zone file's MX records still contain the old resource, the requests never leave the old nameserver to go online to do a fresh search for the real (new) authoritative nameserver. The compounding problem is that the old company is rather inept and doesn't seem to have the technical expertise to identify the problem, much less fix it. (I know, I know.) Is the problem truly that this old zone file just needs to be deleted from the old company's nameserver? If so, what's the best way for me to describe this to them? If not, what do you think could be the issue? Any help is much appreciated. I'm not in IT, so all this is new to me. I know it seems weird for me (the client) to have to do this legwork, but I just want to get this resolved. Here's what I've done: Ran dig to verify that the old server's MX records still point to the old authoritative server, instead of going online to do a fresh search: ~$ dig @old.nameserver.com domainthatwasmoved.com mx ; << DiG 9.6.0-APPLE-P2 << @old.nameserver.com domainThatWasMoved.com mx ; (1 server found) ;; global options: +cmd ;; Got answer: ;; -HEADER<<- opcode: QUERY, status: NOERROR, id: 61227 ;; flags: qr aa rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 1 ;; QUESTION SECTION: ;domainthatwasmoved.com. IN MX ;; ANSWER SECTION: domainthatwasmoved.com. 3600 IN MX 10 mail.oldmailserver.com. ;; ADDITIONAL SECTION: mail.oldmailserver.com. 3600 IN A 65.198.191.5 ;; Query time: 29 msec ;; SERVER: 65.198.191.5#53(65.198.191.5) ;; WHEN: Sun Dec 26 16:59:22 2010 ;; MSG SIZE rcvd: 88 Ran dig to try to see where the new hosting company's servers look when emails are sent from the 3 domains that were moved, and got refused: ~$ dig @new.nameserver.net domainStillAtOldHost.com mx ; << DiG 9.6.0-APPLE-P2 << @new.nameserver.net domainStillAtOldHost.com mx ; (1 server found) ;; global options: +cmd ;; Got answer: ;; -HEADER<<- opcode: QUERY, status: REFUSED, id: 31599 ;; flags: qr rd; QUERY: 1, ANSWER: 0, AUTHORITY: 0, ADDITIONAL: 0 ;; WARNING: recursion requested but not available ;; QUESTION SECTION: ;domainStillAtOldHost.com. IN MX ;; Query time: 31 msec ;; SERVER: 216.201.128.10#53(216.201.128.10) ;; WHEN: Sun Dec 26 17:00:14 2010 ;; MSG SIZE rcvd: 34

    Read the article

  • TV not detected by Windows/VGA - when there is a WHDI device in the signal chain

    - by ashwalk
    I'm at my wit's end with this one... I had an EVGA GTS 250, and I used to plug it's HDMI out into a WHDI sender, which transmitted to its corresponding WHDI receiver 15ft away, which then connected to a Samsung LN40D LCD TV through another HDMI cable. PC/VGA < [hdmi cable] < WHDI sender <[air] WHDI receiver < [hdmi cable] < TV It was perfect, stable, no perceivable latency. I just plugged everything the first time and it worked instantly. It sent 5.1 audio, and Windows/nVidia Control Center detected the TV by its name. The WHDI device is this one: http://goo.gl/Q8iWI5 Now I bought an EVGA GTX 650, and WHDI doesn't work anymore. Both Windows and nVidia Control Center won't detect the TV, only the monitor that's connected via DVI. The TV screen shows "TX202913 connected. Check video signal." on top of a black screen. Though the device is not the problem itself, just the fact that it's not allowing direct connection between PC and TV. I would bet that if put an AVR in its place I'd also have this issue. The HDMI on this new card works with other monitors. If I put the older card back, WHDI works normally. I have googled this for 5 months on and off. Once I bumped into a page that showed how to force a display device to always-on through registry edit. Once I restarted windows, the Tv (through WHDI) displayed my expanded or duplicated desktop at 1024x768 ONLY, and listed the display as "digital display". I could not change the resolution and it wouldn't playback audio (although the option was available at nVidia Control Center HDMI audio options, but did not work). This proves that there is no conflict between the devices, except that software-wise, Windows cannot, for the life of it, understand that there's a TV there to send video/audio to. Since this won't do (no audio, poor video), I reverted this regedit. It's also not an EDID problem within the TV, since when connected directly it works. The last weird bit of this saga is that today, I reminded of Windows' "Add Device" dialog, gave it a go, and a "Samsung Generic UPNP TV" showed up, which I promptly installed the drives for, rising to a climax of... ...NOTHING HAPPENING. As far as I can tell, it really didn't change anything other than using up a few kb in my main disc. I should also say that I looked a LOT into handshake problems and nothing applied either. Do any of you have an idea of what may be going on? I can't stand the thought of having a us$200 device not working because of the addition of a newer graphics card, when the much older one had no issues. There is absolutely NO REASON for this to happen. There is NO documentation on WHDI online. Apparently no one buys this stuff. For the same reason, no one responded to this same plea for help on NVidia and EVGA forums. Worst case, this can be a warning about this setup for people in the future. Thanx in advance.

    Read the article

  • IP address reuse on macvlan devices

    - by Alex Bubnoff
    I'm trying to create easy to use and possibly simple testing environment for some product and got some strange behaviour of macvlan's. What I'm trying to achieve: make a toolset for one-line start/stop of lxc containers(via docker) bound to external ip(I have enough of it on host machine). So, I'm doing something like this: docker run -d -name=container_name container_image pipework eth1 container_name ip/prefix_len@gateway and pipework here does this: GUEST_IFNAME=ph$NSPID$eth1 ip link add link eth1 dev $GUEST_IFNAME type macvlan mode bridge ip link set eth1 up ip link set $GUEST_IFNAME netns $NSPID ip netns exec $NSPID ip link set $GUEST_IFNAME name eth1 ip netns exec $NSPID ip addr add $IPADDR dev eth1 ip netns exec $NSPID ip route delete default ip netns exec $NSPID ip link set eth1 up ip netns exec $NSPID ip route replace default via $GATEWAY ip netns exec $NSPID arping -c 1 -A -I eth1 $IPADDR And it works for first time per IP. But for second time and later packets for containers IP isn't getting into container, while all configuration seem fine. So it looks like this: External machine ? ping 212.76.131.212 ....silence.... Host machine root@ubuntu:~# ip link show eth1 2: eth1: mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:15:17:c9:e1:c9 brd ff:ff:ff:ff:ff:ff root@ubuntu:~# ip addr show eth1 2: eth1: mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:15:17:c9:e1:c9 brd ff:ff:ff:ff:ff:ff root@ubuntu:~# tcpdump -v -i eth1 icmp tcpdump: WARNING: eth1: no IPv4 address assigned tcpdump: listening on eth1, link-type EN10MB (Ethernet), capture size 65535 bytes 00:00:46.542042 IP (tos 0x0, ttl 60, id 9623, offset 0, flags [DF], proto ICMP (1), length 84) 5.134.221.98 212.76.131.212: ICMP echo request, id 6718, seq 2345, length 64 00:00:47.549969 IP (tos 0x0, ttl 60, id 9624, offset 0, flags [DF], proto ICMP (1), length 84) 5.134.221.98 212.76.131.212: ICMP echo request, id 6718, seq 2346, length 64 00:00:48.558143 IP (tos 0x0, ttl 60, id 9625, offset 0, flags [DF], proto ICMP (1), length 84) 5.134.221.98 212.76.131.212: ICMP echo request, id 6718, seq 2347, length 64 00:00:49.566319 IP (tos 0x0, ttl 60, id 9626, offset 0, flags [DF], proto ICMP (1), length 84) 5.134.221.98 212.76.131.212: ICMP echo request, id 6718, seq 2348, length 64 00:00:50.573999 IP (tos 0x0, ttl 60, id 9627, offset 0, flags [DF], proto ICMP (1), length 84) 5.134.221.98 212.76.131.212: ICMP echo request, id 6718, seq 2349, length 64 ^C 5 packets captured 5 packets received by filter 0 packets dropped by kernel 1 packet dropped by interface Host machine, netns of container root@ubuntu:~# ip netns exec 32053 ip link show eth1 48: eth1@if2: mtu 1500 qdisc noqueue state UNKNOWN link/ether b2:12:f7:cc:a1:9d brd ff:ff:ff:ff:ff:ff root@ubuntu:~# ip netns exec 32053 ip addr show eth1 48: eth1@if2: mtu 1500 qdisc noqueue state UNKNOWN link/ether b2:12:f7:cc:a1:9d brd ff:ff:ff:ff:ff:ff inet 212.76.131.212/29 scope global eth1 inet6 fe80::b012:f7ff:fecc:a19d/64 scope link valid_lft forever preferred_lft forever root@ubuntu:~# ip netns exec 32053 tcpdump -v -i eth1 icmp tcpdump: listening on eth1, link-type EN10MB (Ethernet), capture size 65535 bytes ....silence.... ^C 0 packets captured 0 packets received by filter 0 packets dropped by kernel So, can anyone say, what can it be? Can this be caused by not a bug in macvlan implementation? Is there any tools I can use to debug that configuration?

    Read the article

  • Did a recent WinXP update break CD/DVD read speeds? SP2/SP3

    - by quack quixote
    I have two systems with fresh installations of Windows XP Pro SP3 (SP3 slipstreamed into the installer; fully updated after install). One's a refurbished 2.4GHz Pentium4 system; the other is a new 1.6GHz Atom330 build. Both have brand-new dual-layer CD/DVD burners (one's a LiteOn IDE, the other an LG SATA). Both take a really looooong time to read a single-layer DVD in Windows with Cygwin tools. Specifically, 40 minutes or more. I burn backup data to single-layer DVD+/-R and use MD5 hashes for data verification (made with the standard md5sum tool in Unix or Cygwin). The hashes are burned to disc with the data files, and I use this command to verify: $ cd /path/to/disc/mountpoint ; time md5sum -c < md5.txt Here's how long that takes to run on a full single-layer DVD+/-R disc: Old system (WinXP SP2, 1.8GHz Athlon 2500+, last summer): ~10 minutes Old system (Ubuntu 9.04, 1.8GHz Athlon 2500+): ~10 minutes Old system (Debian 5, dual 550MHz P3): ~10 minutes New Pentium4 system (running Ubuntu 9.04): ~5 minutes New Pentium4 system (running WinXP SP3, file copy from Win Explorer): ~6 minutes New Atom330 system (running WinXP SP3, file copy from Win Explorer): ~6 minutes Now the weird stuff: Old system (WinXP SP2, 1.8GHz Athlon 2500+, today): ~25 minutes New Pentium4 system (running WinXP SP3, read from Cygwin): ~40-50 minutes (?!!) New Atom330 system (running WinXP SP3, read from Cygwin): ~40 minutes (can do it in ~30 minutes ...if i have another program spin up the drive first) Since both systems will copy files in 6 minutes using Windows Explorer, I know it's not a hardware problem. Windows just never spins up the drive during the Cygwin read, so it stays super-slow the whole time. Other programs like EAC and DVD Decrypter seem to spin up the disc just fine during their processing. DMA is enabled on both systems. (Can confirm in Windows' Device Manager on the Atom330, not on the P4.) Nero's DriveSpeed tool doesn't seem to have any effect. Copy times are comparable from commandline with Windows' xcopy. Copying with Cygwin's cp looks more like the problem state -- it will spin up the drive for a short time, never reaches full speed, and lets it spin back down again for most of the copy. What I need is to get full read speeds from Cygwin. Is this a known issue with SP3 or some other recent Windows update? Any other ideas? Update: More testing; Windows will spin up the drive when data is copied with Windows tools, but not when read in place or copied with Cygwin tools. It doesn't make sense to me that Windows spins up the drive for copying, but not for other reads. Might be more of a Cygwin problem? Update 2: GUI activity is sluggish during the problem state -- during the Cygwin verifies, there's a slight but noticable delay when dragging windows or icons around on the desktop, switching windows, Alt-Tabbing through open applications, opening new windows, etc. It reminds me of the delay when opening a Windows Explorer window on My Computer just after inserting a DVD. I've tried updating Cygwin (from 1.5.x to 1.7.x), but no change in the problem behavior. I've also noticed this issue occurs on WinXP SP2, but it's not exactly the same -- some spin-up occurs, so the read happens in ~25-30 minutes instead of 40+. The SP2 system used to run the verifies in ~10 minutes, and when it first changed (not sure exactly when, maybe in late November or early December 2009) I thought it was dying hardware. This is why I suspect an official update of breaking this functionality; this has worked for years on that SP2 box.

    Read the article

  • Difference between `curl -I` and `curl -X HEAD`

    - by chmeee
    I was wathcing the funny server type from http://www.reddit.com with curl -I http://www.reddit.com when I guessed that curl -X HEAD http://www.reddit.com would do the same. But, in fact, it doesn't. I'm curious about why. This is what I observe running the two commands: curl -I: works as expected, outputs the header and exists. curl -X HEAD: does not show anything and seems to wait for user input. But, sniffing with tshark I see the second command actually sends the same HTML query and receives the correct answer, but it does not show it and it doesn't close the connection. curl -I 0.000000 333.33.33.33 -> 213.248.111.106 TCP 59675 > http [SYN] Seq=0 Win=5840 Len=0 MSS=1460 TSV=47267342 TSER=0 WS=6 0.045392 213.248.111.106 -> 333.33.33.33 TCP http > 59675 [SYN, ACK] Seq=0 Ack=1 Win=5792 Len=0 MSS=1460 TSV=2552532839 TSER=47267342 WS=1 0.045441 333.33.33.33 -> 213.248.111.106 TCP 59675 > http [ACK] Seq=1 Ack=1 Win=5888 Len=0 TSV=47267353 TSER=2552532839 0.045623 333.33.33.33 -> 213.248.111.106 HTTP HEAD / HTTP/1.1 0.091665 213.248.111.106 -> 333.33.33.33 TCP http > 59675 [ACK] Seq=1 Ack=155 Win=6432 Len=0 TSV=2552532886 TSER=47267353 0.861782 213.248.111.106 -> 333.33.33.33 HTTP HTTP/1.1 200 OK 0.861830 333.33.33.33 -> 213.248.111.106 TCP 59675 > http [ACK] Seq=155 Ack=321 Win=6912 Len=0 TSV=47267557 TSER=2552533656 0.862127 333.33.33.33 -> 213.248.111.106 TCP 59675 > http [FIN, ACK] Seq=155 Ack=321 Win=6912 Len=0 TSV=47267557 TSER=2552533656 0.910810 213.248.111.106 -> 333.33.33.33 TCP http > 59675 [FIN, ACK] Seq=321 Ack=156 Win=6432 Len=0 TSV=2552533705 TSER=47267557 0.910880 333.33.33.33 -> 213.248.111.106 TCP 59675 > http [ACK] Seq=156 Ack=322 Win=6912 Len=0 TSV=47267570 TSER=2552533705 curl -X HEAD 34.106389 333.33.33.33 -> 213.248.111.90 TCP 51690 > http [SYN] Seq=0 Win=5840 Len=0 MSS=1460 TSV=47275868 TSER=0 WS=6 34.149507 213.248.111.90 -> 333.33.33.33 TCP http > 51690 [SYN, ACK] Seq=0 Ack=1 Win=5792 Len=0 MSS=1460 TSV=3920268348 TSER=47275868 WS=1 34.149560 333.33.33.33 -> 213.248.111.90 TCP 51690 > http [ACK] Seq=1 Ack=1 Win=5888 Len=0 TSV=47275879 TSER=3920268348 34.149646 333.33.33.33 -> 213.248.111.90 HTTP HEAD / HTTP/1.1 34.191484 213.248.111.90 -> 333.33.33.33 TCP http > 51690 [ACK] Seq=1 Ack=155 Win=6432 Len=0 TSV=3920268390 TSER=47275879 34.192657 213.248.111.90 -> 333.33.33.33 TCP [TCP Dup ACK 15#1] http > 51690 [ACK] Seq=1 Ack=155 Win=6432 Len=0 TSV=3920268390 TSER=47275879 34.823399 213.248.111.90 -> 333.33.33.33 HTTP HTTP/1.1 200 OK 34.823453 333.33.33.33 -> 213.248.111.90 TCP 51690 > http [ACK] Seq=155 Ack=321 Win=6912 Len=0 TSV=47276048 TSER=3920269022 Any idea about why this difference in behaviour?

    Read the article

  • iPhone doesn't save password for Cisco IPsec VPN using racoon daemon

    - by dsx
    On my Debian server I had set up racoon daemon (1:0.8.0-14) for Cisco IPSec VPN using certificates for authentication. My racoon.conf is like following: log info; path certificate "/etc/racoon/certs"; listen { isakmp $SERVER_IP_HERE [500]; isakmp_natt $SERVER_IP_HERE [4500]; } timer { natt_keepalive 10 sec; } remote anonymous { lifetime time 24 hours; proposal_check obey; passive on; exchange_mode aggressive,main; my_identifier asn1dn; peers_identifier asn1dn; verify_identifier on; certificate_type x509 "cert_name.crt" "key_name.key"; ca_type x509 "ca.crt"; mode_cfg on; verify_cert on; ike_frag on; generate_policy on; nat_traversal on; dpd_delay 20; proposal { encryption_algorithm aes; hash_algorithm sha1; authentication_method xauth_rsa_server; dh_group modp1024; } } mode_cfg { conf_source local; auth_source system; auth_throttle 3; save_passwd on; dns4 8.8.8.8; network4 $SOME_LAN_SUBNET; netmask4 255.255.255.0; pool_size 128; } sainfo anonymous { pfs_group 2; lifetime time 24 hour; encryption_algorithm aes; authentication_algorithm hmac_sha1; compression_algorithm deflate; } I'm not using PSK authentication here. Using iPhone configuration utility I had uploaded all required certificates to iPhone and set up VPN on demand. Everything works just fine except one thing: iPhone refuses to save VPN password regardless of save_passwd on; in racoon configuration file. As opposed to iPhone behaviour, Mac OS X 10.8.2 have no problems saving password. I had examined iPhone log file and found following: racoon[151] <Notice>: >>>>> phase change status = phase 1 established configd[50] <Notice>: IPSec Network Configuration started. configd[50] <Notice>: IPSec Network Configuration: INTERNAL-IP4-ADDRESS = $SUBNET_IP_HERE. configd[50] <Notice>: IPSec Network Configuration: INTERNAL-IP4-MASK = 255.255.255.0. configd[50] <Notice>: IPSec Network Configuration: SAVE-PASSWORD = 0. configd[50] <Notice>: IPSec Network Configuration: INTERNAL-IP4-DNS = 8.8.8.8. configd[50] <Notice>: IPSec Network Configuration: BANNER = . configd[50] <Notice>: IPSec Network Configuration: DEF-DOMAIN = . configd[50] <Notice>: IPSec Network Configuration: DEFAULT-ROUTE = local-address $SUBNET_IP_HERE/32. configd[50] <Notice>: IPSec Phase2 starting. configd[50] <Notice>: IPSec Network Configuration established. configd[50] <Notice>: IPSec Phase1 established. Please note IPSec Network Configuration message containing SAVE-PASSWORD = 0.. Is it a bug in racoon daemon on server, or iPhone (iOS version is 6.0.1 (10A523)) or it is me missing something? How to make iPhone remember IPSec VPN password?

    Read the article

  • IMAPSync Migration to Exchange 2010 SP1: Exchange drops connections while checking for existence of folders

    - by Benjamin Priestman
    I'm migrating from ZImbra Collaboration Suite to Exchange 2010 SP1. I'm testing IMAPSync as a possible migration tool and have hit a problem with the IMAP server in Exchange 2010. For each account it migrates, IMAPSync loops through the list of folders in the source mailbox and tests for the existence of each one in the destination mailbox. It then goes on to create those folders that do not exist and copy over the messages. It's the intial testing for the existence of the folders that is giving me a problem. The response given by the Exchange server when the folder does not yet exist is given as an error: "R=""16 NO IMAPSyncTest/8 doesn't exist."" After ten of these errors have been issued in succession, the Exchange server appears to stop responding to the IMAP session. Enabling protocol logging for IMAP confirms that the 10th request for a non-existant folder is the last request to be logged on the server. IMAPSync carries on merrily without seeming to realise its connection has gone and thus fails to create any folders. I've logged this with the tool's creator. Does anyone have any idea why Exchange is stopping responding to the connections though? The behaviour looks rather like throttling, although the 'ten strikes and you're out' trigger does not seem to correspond to any of the triggers on the ThrottlingPolicies. Just to check, I've tried creating a new ThrottlingPolicy, turned everything that I think might be relevant up to 11 and applied it to the my test mailbox. Policy settings are listed below, along with IMAP settings. Everything else should be pretty much as default. Throttling Policy RunspaceId : afa3159c-32a6-4906-986f-8adfbe50868b IsDefault : False AnonymousMaxConcurrency : 1 AnonymousPercentTimeInAD : AnonymousPercentTimeInCAS : AnonymousPercentTimeInMailboxRPC : EASMaxConcurrency : 10 EASPercentTimeInAD : EASPercentTimeInCAS : EASPercentTimeInMailboxRPC : EASMaxDevices : 10 EASMaxDeviceDeletesPerMonth : EWSMaxConcurrency : 10 EWSPercentTimeInAD : 50 EWSPercentTimeInCAS : 90 EWSPercentTimeInMailboxRPC : 60 EWSMaxSubscriptions : 5000 EWSFastSearchTimeoutInSeconds : 60 EWSFindCountLimit : 1000 IMAPMaxConcurrency : 1000 IMAPPercentTimeInAD : 400 IMAPPercentTimeInCAS : 400 IMAPPercentTimeInMailboxRPC : 400 OWAMaxConcurrency : 5 OWAPercentTimeInAD : 30 OWAPercentTimeInCAS : 150 OWAPercentTimeInMailboxRPC : 150 POPMaxConcurrency : 20 POPPercentTimeInAD : POPPercentTimeInCAS : POPPercentTimeInMailboxRPC : PowerShellMaxConcurrency : 18 PowerShellMaxTenantConcurrency : PowerShellMaxCmdlets : PowerShellMaxCmdletsTimePeriod : ExchangeMaxCmdlets : PowerShellMaxCmdletQueueDepth : PowerShellMaxDestructiveCmdlets : PowerShellMaxDestructiveCmdletsTimePeriod : RCAMaxConcurrency : 1000 RCAPercentTimeInAD : 400 RCAPercentTimeInCAS : 400 RCAPercentTimeInMailboxRPC : 400 CPAMaxConcurrency : 20 CPAPercentTimeInCAS : 205 CPAPercentTimeInMailboxRPC : 200 MessageRateLimit : RecipientRateLimit : ForwardeeLimit : CPUStartPercent : 75 AdminDisplayName : ExchangeVersion : 0.10 (14.0.100.0) Name : TestMigrationThrottling DistinguishedName : CN=TestMigrationThrottling,CN=Global Settings,CN=Our Company,CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=cimex,DC=com Identity : TestMigrationThrottling Guid : 240049b3-2023-4df1-8edc-fbfc1fc80b87 ObjectCategory : domain.com/Configuration/Schema/ms-Exch-Throttling-Policy ObjectClass : {top, msExchGenericPolicy, msExchThrottlingPolicy} WhenChanged : 21/04/2011 18:48:19 WhenCreated : 21/04/2011 18:07:20 WhenChangedUTC : 21/04/2011 17:48:19 WhenCreatedUTC : 21/04/2011 17:07:20 OrganizationId : OriginatingServer : a-domain-controller IsValid : True IMAPSettings RunspaceId : afa3159c-32a6-4906-986f-8adfbe50868b ProtocolName : IMAP4 Name : 1 MaxCommandSize : 10240 ShowHiddenFoldersEnabled : False UnencryptedOrTLSBindings : {192.168.x.x:143} SSLBindings : {192.168.x.x:993} InternalConnectionSettings : {mail.office.domain.com:143:TLS, mail.office.domain.com:993:SSL} ExternalConnectionSettings : {mail.office.domain.com:143:TLS, mail.office.domain.com:993:SSL} X509CertificateName : mail.domain.com Banner : The Microsoft Exchange IMAP4 service is ready. LoginType : SecureLogin AuthenticatedConnectionTimeout : 00:30:00 PreAuthenticatedConnectionTimeout : 00:01:00 MaxConnections : 2147483647 MaxConnectionFromSingleIP : 2147483647 MaxConnectionsPerUser : 16 MessageRetrievalMimeFormat : BestBodyFormat ProxyTargetPort : 143 CalendarItemRetrievalOption : iCalendar OwaServerUrl : EnableExactRFC822Size : False LiveIdBasicAuthReplacement : False SuppressReadReceipt : False ProtocolLogEnabled : True EnforceCertificateErrors : False LogFileLocation : C:\Program Files\Microsoft\Exchange Server\V14\Logging\Imap4 LogFileRollOverSettings : Daily LogPerFileSizeQuota : 0 B (0 bytes) ExtendedProtectionPolicy : None EnableGSSAPIAndNTLMAuth : True Server : CMX-OFFICE-EX01 AdminDisplayName : ExchangeVersion : 0.10 (14.0.100.0) DistinguishedName : CN=1,CN=IMAP4,CN=Protocols,CN=EXCHANGE01,CN=Servers,CN=Exchange Administrative Group (FYDIBOHF23SPDLT),CN=Administrative Groups,CN=Our COmpany,CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=domain,DC=com Identity : EXCHANGE01\1 Guid : 48f9dc37-74c2-4fb0-a042-641f863f45f2 ObjectCategory : domain.com/Configuration/Schema/ms-Exch-Protocol-Cfg-IMAP-Server ObjectClass : {top, protocolCfg, protocolCfgIMAP, protocolCfgIMAPServer} WhenChanged : 21/04/2011 17:03:39 WhenCreated : 15/04/2011 13:51:58 WhenChangedUTC : 21/04/2011 16:03:39 WhenCreatedUTC : 15/04/2011 12:51:58 OrganizationId : OriginatingServer : a-domain-server IsValid : True

    Read the article

  • Logitech USB headphones detected and selected in Debian Squeeze but sound still coming from speakers

    - by mattalexx
    I have a pair of Logitech wireless USB headphones that work with Ubuntu Natty but aren't working in Debian Squeeze. When they are selected as the default audio output, the sound comes out of the speakers instead of the headphones. I have rebooted and tried using a different USB port. My computer is a Thinkpad T510. How can I fix this problem? Here is lsusb: Bus 002 Device 005: ID 046d:0a29 Logitech, Inc. Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 005: ID 046d:c52f Logitech, Inc. Wireless Mouse M305 Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Here is cat /proc/asound/cards 0 [Intel ]: HDA-Intel - HDA Intel HDA Intel at 0xf2420000 irq 17 1 [Headset ]: USB-Audio - Logitech Wireless Headset Logitech Logitech Wireless Headset at usb-0000:00:1d.0-1.1, full speed 2 [NVidia ]: HDA-Intel - HDA NVidia HDA NVidia at 0xcdefc000 irq 17 Here is the gnome-volume-control GUI: Here's lsmod | grep usb: snd_usb_audio 50670 0 snd_usb_lib 11192 1 snd_usb_audio usbhid 28008 0 hid 50909 1 usbhid snd_rawmidi 12513 2 snd_usb_lib,snd_seq_midi snd_hwdep 4054 2 snd_usb_audio,snd_hda_codec snd_pcm 47226 3 snd_usb_audio,snd_hda_intel,snd_hda_codec usbcore 98969 5 snd_usb_audio,snd_usb_lib,usbhid,ehci_hcd snd 34423 11 snd_usb_audio,snd_rawmidi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_seq,snd_timer,snd_seq_device nls_base 4541 1 usbcore Here's cat /etc/modprobe.d/alsa-base.conf: # autoloader aliases install sound-slot-0 /sbin/modprobe snd-card-0 install sound-slot-1 /sbin/modprobe snd-card-1 install sound-slot-2 /sbin/modprobe snd-card-2 install sound-slot-3 /sbin/modprobe snd-card-3 install sound-slot-4 /sbin/modprobe snd-card-4 install sound-slot-5 /sbin/modprobe snd-card-5 install sound-slot-6 /sbin/modprobe snd-card-6 install sound-slot-7 /sbin/modprobe snd-card-7 # Cause optional modules to be loaded above generic modules install snd /sbin/modprobe --ignore-install snd && { /sbin/modprobe --quiet snd-ioctl32 ; /sbin/modprobe --quiet snd-seq ; } install snd-rawmidi /sbin/modprobe --ignore-install snd-rawmidi && { /sbin/modprobe --quiet snd-seq-midi ; : ; } install snd-emu10k1 /sbin/modprobe --ignore-install snd-emu10k1 && { /sbin/modprobe --quiet snd-emu10k1-synth ; : ; } # Prevent abnormal drivers from grabbing index 0 options bt87x index=-2 options cx88_alsa index=-2 options snd-atiixp-modem index=-2 options snd-intel8x0m index=-2 options snd-via82xx-modem index=-2 # Keep snd-pcsp from beeing loaded as first soundcard options snd-pcsp index=-2 # Keep snd-usb-audio from beeing loaded as first soundcard options snd-usb-audio index=-2 EDIT In VLC, I reset VLC prefs (Output: Default) and sound still comes out of speakers as expected. Then I change it to "Output: ALSA Audio output" and a Device menu appears. I select the headphones. When I then save the prefs, the audio switch to the headphones! But here's what's weird: I go back to prefs, change it to "Output: Default" and the headphones keep working. Maybe the ALSA option is actually what is being chosen as the "Default" option, but the Device menu (whose selection is still being used) is still set to the headphones. Anyway, now I need to figure out how to make it work as the default for the whole system.

    Read the article

  • PHP.ini does not load

    - by Jonathan Park
    Ok this is probably just me not knowing enough about php but here it goes. I'm on Ubuntu Hardy. I have a custom compiled version of PHP which I have compiled with these parameters. ./configure --enable-soap --with-zlib --with-mysql --with-apxs2=[correct path] --with-config-file-path=[correct path] --with-mysqli --with-curlwrappers --with-curl --with-mcrypt I have used the command pecl install pecl_http to install the http.so extension. It is in the correct module directory for my php.ini. My php.ini is loading and I can change things within the ini and effect php. I have included the extension=http.so line in my php.ini. That worked fine. Until I added these compilation options in order to add imap --with-openssl --with-kerberos --with-imap --with-imap-ssl Which failed because I needed the c-client library which I fixed by apt-get install libc-client-dev After which php compiles fine and I have working imap support, woo. HOWEVER, now all my calls to HttpRequest which is part of the pecl_http extention in http.so result in Fatal error: Class 'HttpRequest' not found errors. I figure the http.so module is no longer loading for one reason or another but I cannot find any errors showing the reason. You might say "Have you tried undoing the new imap setup?" To which I will answer. Yes I have. I directly undid all my config changes and uninstalled the c-client library and I still can't get it to work. I thought that's weird... I have made no changes that would have resulted in this issue. After looking at that I have also discovered that not only is the http extension no longer loading but all my extensions loaded via php.ini are no longer loading. Can someone at least give me some further debugging steps? So far I have tried enabling all errors including startup errors in my php.ini which works for other errors, but I'm not seeing any startup errors either on command line or via apache. And yet again the php.ini appears to be being parsed given that if I run php_info() I get settings that are in the php.ini. Edit it appears that only some of the php.ini settings are being listened to. Is there a way to test my php.ini? Edit Edit It appears I am mistaken again and the php.ini is not being loaded at all any longer. However, If I run php_info() I get that it's looking for my php.ini in the correct location. Edit Edit Edit My config is at the config file path location below but it says no config file loaded. WTF Permission issue? It is currently 644 so everyone should be able to read it if not write it. I tried making it 777 and that didn't work. Configuration File (php.ini) Path /etc/php.ini Loaded Configuration File (none) Edit Edit Edit Edit By loading the ini on the command line using the -c command I am able to run my files and using -m shows that my modules load So nothing is wrong with the php.ini

    Read the article

  • Rsyslog is not working properly, it does not log anything

    - by Victor Henriquez
    I'm running a Debian server and a couple of days ago my rsyslog started to behave very weird, the daemon is running but it doesn't seem to do anything. Many people use the system but I'm the only one with (legal) root access. I'm using the default rsyslogd configuration (if you think is relevant I'll attach it, but it's the one that comes with the package). After I rotated all the log files, they have remained empty: # ls -l /var/log/*.log -rw-r--r-- 1 root root 0 Jun 27 00:25 /var/log/alternatives.log -rw-r----- 1 root adm 0 Jun 26 13:03 /var/log/auth.log -rw-r----- 1 root adm 0 Jun 26 13:03 /var/log/daemon.log -rw-r--r-- 1 root root 0 Jun 27 00:25 /var/log/dpkg.log -rw-r----- 1 root adm 0 Jun 26 13:03 /var/log/kern.log -rw-r----- 1 root adm 0 Jun 26 13:03 /var/log/lpr.log -rw-r----- 1 root adm 0 Jun 26 13:03 /var/log/mail.log -rw-r----- 1 root adm 0 Jun 26 13:03 /var/log/user.log Any try to force a log writing does not have any effect: # logger hey # ls -l /var/log/messages -rw-r----- 1 root adm 0 Jun 26 13:03 /var/log/messages Lsof shows that rsyslogd does not have any log files opened: # lsof -p 1855 COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME rsyslogd 1855 root cwd DIR 202,0 4096 2 / rsyslogd 1855 root rtd DIR 202,0 4096 2 / rsyslogd 1855 root txt REG 202,0 342076 21649 /usr/sbin/rsyslogd rsyslogd 1855 root mem REG 202,0 38556 32153 /lib/i386-linux-gnu/i686/cmov/libnss_nis-2.13.so rsyslogd 1855 root mem REG 202,0 79728 32165 /lib/i386-linux-gnu/i686/cmov/libnsl-2.13.so rsyslogd 1855 root mem REG 202,0 26456 32163 /lib/i386-linux-gnu/i686/cmov/libnss_compat-2.13.so rsyslogd 1855 root mem REG 202,0 297500 1061058 /usr/lib/rsyslog/imuxsock.so rsyslogd 1855 root mem REG 202,0 42628 32170 /lib/i386-linux-gnu/i686/cmov/libnss_files-2.13.so rsyslogd 1855 root mem REG 202,0 22784 1061106 /usr/lib/rsyslog/imklog.so rsyslogd 1855 root mem REG 202,0 1401000 32169 /lib/i386-linux-gnu/i686/cmov/libc-2.13.so rsyslogd 1855 root mem REG 202,0 30684 32175 /lib/i386-linux-gnu/i686/cmov/librt-2.13.so rsyslogd 1855 root mem REG 202,0 9844 32157 /lib/i386-linux-gnu/i686/cmov/libdl-2.13.so rsyslogd 1855 root mem REG 202,0 117009 32154 /lib/i386-linux-gnu/i686/cmov/libpthread-2.13.so rsyslogd 1855 root mem REG 202,0 79980 17746 /usr/lib/libz.so.1.2.3.4 rsyslogd 1855 root mem REG 202,0 18836 1061094 /usr/lib/rsyslog/lmnet.so rsyslogd 1855 root mem REG 202,0 117960 31845 /lib/i386-linux-gnu/ld-2.13.so rsyslogd 1855 root 0u unix 0xebe8e800 0t0 640 /dev/log rsyslogd 1855 root 3u FIFO 0,5 0t0 2474 /dev/xconsole rsyslogd 1855 root 4u unix 0xebe8e400 0t0 645 /var/spool/postfix/dev/log rsyslogd 1855 root 5r REG 0,3 0 4026532176 /proc/kmsg I was so frustrated that even reinstall the rsyslog package, but it still refuses to log anything: # apt-get remove --purge rsyslog # apt-get install rsyslog I thought someone had hacked the system, so run rkhunter, chkrootkit, unhide in an attempt to find hide processes / ports and nmap in a remote host to compare with the ports shown by netstat. And I know this doesn't mean anything, but all looks ok. The system also have an iptables firewall that is very restrictive with incoming / outgoing connections. This is driving me crazy, any idea what is going on here? [EDIT - disk space info] # df -h Filesystem Size Used Avail Use% Mounted on rootfs 24G 22G 629M 98% / /dev/root 24G 22G 629M 98% / devtmpfs 10M 112K 9.9M 2% /dev tmpfs 76M 48K 76M 1% /run tmpfs 5.0M 0 5.0M 0% /run/lock tmpfs 151M 40K 151M 1% /tmp tmpfs 151M 0 151M 0% /run/shm

    Read the article

  • Putting indexes in separate filegroup kills our queries

    - by womp
    Can anyone shed some light on this? On our dev boxes, our database resides entirely in the PRIMARY filegroup, and everything works fine. On one of our production servers, recently upgraded from 2005 to 2008, we noticed it was performing slower than it should. On this machine, there are two filegroups - PRIMARY and INDEXES. Both filegroups contain 1 file per logical volume, one logical volume per CPU, (and each logical volume is a RAID 10 of 4 physical disks). We isolated a few queries that were performing fast on the dev boxes and slow (up to 40x slower) on the production machine. Turned out these queries were using the non-clustered indexes that resided in the INDEXES filegroup. Tweaking some of the queries to only use clustered indexes that were in the PRIMARY filegroup dropped their times back to normal. As a final confirmation, we redeployed the same database on the same machine to have everything in PRIMARY, and things went back to normal! Here's the statistics output of one of the queries, run identically on the machine with different filegroup configurations (table names changed to protect the innocent): FAST (everything in PRIMARY filegroup): (3 row(s) affected) Table '0'. Scan count 2, logical reads 14, ... Table '1'. Scan count 0, logical reads 0, ... Table '1'. Scan count 0, logical reads 0, ... Table '2'. Scan count 2, logical reads 7, ... Table '3'. Scan count 2, logical reads 1012, ... Table '4'. Scan count 1, logical reads 3, ... SQL Server Execution Times: CPU time = 437 ms, elapsed time = 445 ms. SLOW (indexes split into their own filegroup): (3 row(s) affected) Table '0'. Scan count 209, logical reads 428, ... Table '1'. Scan count 0, logical reads 0,... Table '2'. Scan count 1021, logical reads 9043,.... Table '3'. Scan count 209, logical reads 105754, .... Table '4'. Scan count 0, logical reads 0, .... Table '5'. Scan count 1, logical reads 695, ... **Table '#46DA8CA9'. Scan count 205, logical reads 205, ...** Table '6'. Scan count 6, logical reads 436, ... Table '7'. Scan count 1, logical reads 12,.... SQL Server Execution Times: CPU time = 17581 ms, elapsed time = 17595 ms. Notice the weird temp table and extra tables involved in the slow query. It seems clear that having a second file group is making SQL Server batty with choosing an execution plan. What the heck is going on?

    Read the article

  • Thoughts on home NAS server

    - by user826955
    I currently have a NAS with a 2x2TB HDD 1x16GB SSD layout on a mini-itx atom board. The NAS is in a Lian Li PC-Q07 case. On this system I was running freebsd 8 with a gmirror raid 1 setup, which was enough for my needs. So far I was using the NAS for: Fileserver with AFP protocol (only mac clients used) SVN server hosting all my source trees of my projects JIRA (performance was okay-ish) Timemachine backup for the macs The power consumption was about 38W, although I did not put HDDs asleep when unused (I think this is not possible in a raid setup). I liked the NAS because: the performance was good through gigabit LAN (enough for my needs) power consumption was good its a pretty small case and fits in one of my cupboards I disliked the NAS a bit because: it was a bit noisy, the Q07 case vibrated a good amount because of the HDDs. I switched the NAS off every evening I do not have a real backup of the data on the NAS, only the internal raid 1 as safety. I really dont want to loose my source trees under no circumstances, so I would really be sleeping better if I knew I had regular backups somewhere. Recently, the board seemed to have died, I can't boot anymore. Thus, I was thinking about a redesign of my NAS (I still have to find out what parts are broken, I probably need to replace the mainboard and SSD. HDDs seem to be okay). First of all, I was wondering what other users have as backup for their NAS? Are you actually using a second NAS, and regularly copying over the data to have it safe? Or is there any better solution to this? I was thinking about getting a cheap NAS like the synology DS112j with only one disk, and use rsync or something similar to regularly copy data over to the second NAS (wake the second NAS upon start, shut it down after copy). Although this approach seems somewhat weird, It would have the benefit (?) that I could use a single disk instead of raid in the main NAS, and put the disk asleep when idle, and have the NAS running 24/7 with low energy consumption (I found no way to do this with a gmirror setup). Is there any recommended backup solution for a small NAS? Then I was thinking about a different raid setup. Since I have to buy a new mainboard as well as SSD, I might as well switch over to a i3 board with more ram, and also switch to ZFS. I am not familar with ZFS, I've never used it, but I read and hear much about it. Would it be viable to set up a ZFS storage with only 2 disks? Can I easily extend this storage with more disks, once I choose to add some? I could maybe get a new case like the Fractal Design Array R2 which has more 3,5" slots. I could as well get another 2 disks, but I would prefer sticking with the existing 2 for enegery/heat/noise reasons. Should I go for a ZFS storage or stick to my gmirror setup? I would also like to keep freebsd as operating system, and also I dont need any web gui or something (that is, I dont need/want to use FreeNAS or Openfiler etc). Does anyone maybe have a sample setup in use so I can compare energy consumption/noise/software setup? Any guidance towards the NAS of my dreams (silent, low energy, safe w/ backups) much appreciated.

    Read the article

  • centos6.3 varnish3.03 get the wrong backend

    - by Sola.Shawn
    I install varnish3.03 with yum! I got a problem with it my varnish config bellow:** # #backend weibo { .host = "192.168.1.178"; .port = "8080"; .connect_timeout=20s; .first_byte_timeout=20s; .between_bytes_timeout=20s; } #backend smth { .host = "192.168.1.115"; .port = "8080"; .connect_timeout=20s; .first_byte_timeout=20s; .between_bytes_timeout=20s; } #sub vcl_recv { if (req.restarts == 0) { if (req.http.x-forwarded-for) { set req.http.X-Forwarded-For = req.http.X-Forwarded-For + ", " + client.ip; } else { set req.http.X-Forwarded-For = client.ip; } } if (req.request != "GET" && req.request != "HEAD" && req.request != "PUT" && req.request != "POST" && req.request != "TRACE" && req.request != "OPTIONS" && req.request != "DELETE") { # /* Non-RFC2616 or CONNECT which is weird. */ return(pipe); } if (req.request != "GET" && req.request != "HEAD") { # /* We only deal with GET and HEAD by default */ return(pass); } if (req.http.Authorization || req.http.Cookie) { /* Not cacheable by default */ return(pass); } if (req.http.host ~ "^(hk.)?weibo.com"){ set req.http.host = "hk.weibo.com"; set req.backend = weibo; } elseif (req.http.host ~ "^(www.)?newsmth.net"){ set req.http.host = "www.newsmth.net"; set req.backend = smth; } else { error 404 "Unknown virtual host"; } return(lookup); } ##sub vcl_pipe { return(pipe); } #sub vcl_pass { return(pass); } #sub vcl_hash { hash_data(req.url); if(req.http.host) { hash_data(req.http.host); } else { hash_data(server.ip); } return(hash); } #sub vcl_hit { if(req.http.Cache-Control~"no-cache"||req.http.Cache-Control~"max-age=0"||req.http.Pragma~"no-cache"){ set obj.ttl=0s; return (restart); } return(deliver); } #sub vcl_miss { return(fetch); } #sub vcl_fetch { if (beresp.ttl <= 120s || beresp.http.Set-Cookie || beresp.http.Vary == "*") { /* * Mark as "Hit-For-Pass" for the next 2 minutes */ set beresp.ttl = 10s; return (hit_for_pass); } return(deliver); } #sub vcl_deliver { return(deliver); } #sub vcl_init { return(ok); } #sub vcl_fini { return(ok); } and my Win7's hosts file add bellow: 192.168.1.178 www.newsmth.net 192.168.1.178 hk.weibo.com start varnish varnishd -f /etc/varnish/dd.vcl -s malloc,100M -a 0.0.0.0:8000 -T 0.0.0.0:3500<br> but when I access the "hk.weibo.com:8000" it fine, and got: Hello,I am hk.weibo.com! but when access http://www.newsmth.net:8000/, got: Hello,I am hk.weibo.com! <br> My question is why it isn't "Hello,I am www.newsmth.net!"? varnish fetched the content from the wrong backend. Does anyone know how to fix this?

    Read the article

  • Amazon EC2 Instance - m1.medium Ubuntu 12.04 - Started to crash three days ago

    - by Joy
    The environment: Amazon EC2 Instance - m1.medium Ubuntu 12.04 Apache 2.2.22 - Running a Drupal Site Using MySQL DB Server RAM info: ~$ free -gt total used free shared buffers cached Mem: 3 1 2 0 0 0 -/+ buffers/cache: 0 2 Swap: 0 0 0 Total: 3 1 2 Hard drive info: Filesystem Size Used Avail Use% Mounted on /dev/xvda1 7.9G 4.7G 2.9G 62% / udev 1.9G 8.0K 1.9G 1% /dev tmpfs 751M 180K 750M 1% /run none 5.0M 0 5.0M 0% /run/lock none 1.9G 0 1.9G 0% /run/shm /dev/xvdb 394G 199M 374G 1% /mnt The problem About two days ago the site started failing becaue the MySQL server was shut down by Apache with the following message: kernel: [2963685.664359] [31716] 106 31716 226946 22748 0 0 0 mysqld kernel: [2963685.664730] Out of memory: Kill process 31716 (mysqld) score 23 or sacrifice child kernel: [2963685.664764] Killed process 31716 (mysqld) total-vm:907784kB, anon-rss:90992kB, file-rss:0kB kernel: [2963686.153608] init: mysql main process (31716) killed by KILL signal kernel: [2963686.169294] init: mysql main process ended, respawning That states that the VM was occupying 0.9GB, but my Ram has 2GB free, so 1GB was still left free. I understand that in Linux applications can allocate more memory than physically available. I don't know if this is the problme, it's the first time that it has started to happen. Obviously, the MySQL server tries to restart, but there's no memory for it apparently and it won't restart. Here is its error log: Plugin 'FEDERATED' is disabled. The InnoDB memory heap is disabled Mutexes and rw_locks use GCC atomic builtins Compressed tables use zlib 1.2.3.4 Initializing buffer pool, size = 128.0M InnoDB: mmap(137363456 bytes) failed; errno 12 Completed initialization of buffer pool Fatal error: cannot allocate memory for the buffer pool Plugin 'InnoDB' init function returned error. Plugin 'InnoDB' registration as a STORAGE ENGINE failed. Unknown/unsupported storage engine: InnoDB [ERROR] Aborting [Note] /usr/sbin/mysqld: Shutdown complete I simply restarted the Mysql service. About two hours later it happened again. I restarted it. Then it happened again 9 hours later. So then I thought of the MaxClients parameter of apache.conf, so I went to check it out. It was set at 150. I decided to drop it down to 60. As so: <IfModule mpm_prefork_module> ... MaxClients 60 </IfModule> <IfModule mpm_worker_module> ... MaxClients 60 </IfModule> <IfModule mpm_event_module> ... MaxClients 60 </IfModule> Once I did that, I had the apache2 service restart and it all went smoothly for 3/4 of a day. Since at night the MySQL service shut down once again, but this time it wasn't killed by the Apache2 service. Instead it called the OOM-Killer with the following message: kernel: [3104680.005312] mysqld invoked oom-killer: gfp_mask=0x201da, order=0, oom_adj=0, oom_score_adj=0 kernel: [3104680.005351] [<ffffffff81119795>] oom_kill_process+0x85/0xb0 kernel: [3104680.548860] init: mysql main process (30821) killed by KILL signal Now I'm out of ideas. Some articles state that the ideal thing to do is change the kernel behaviour with the following (include it to the file /etc/sysctl.conf ) vm.overcommit_memory = 2 vm.overcommit_ratio = 80 So no overcommits will take place. I'm wondering if this is the way to go? Keep in mind I'm no server administrator, I have basic knowldege. Thanks a bunch in advance.

    Read the article

  • Configuring dhcp module in FreeRadius (3.0.2 - Centos 6.5)

    - by mixja
    I am using the REST module to authorise a DHCP request. I would like to send an explicit DHCP NAK if the authorisation fails, however the DHCP module seems to return immediately if there is a failure and just ignores the DHCP request without any response. Here is my DHCP module configuration - if rest.authorize is successful, the if (ok) control block is hit, but if rest.authorize fails the if (fail) is never hit. dhcp DHCP-Discover { rest.authorize if (fail) { update reply { DHCP-Message-Type = DHCP-Nak } } if (ok) { update reply { DHCP-Message-Type = DHCP-Offer } update reply { DHCP-Domain-Name-Server = x.x.x.x DHCP-Domain-Name-Server = x.x.x.x DHCP-Subnet-Mask = 255.255.255.0 DHCP-Router-Address = x.x.x.x DHCP-IP-Address-Lease-Time = 3600 DHCP-DHCP-Server-Identifier = x.x.x.x } mac2ip } } Below is the output after a 401 Unauthorized is received. I am wanting to achieve a temporary block on DHCP for a specified (small) period of time. However the FreeRADIUS behaviour is to ignore duplicate requests for same DHCP transaction, meaning DHCP on client is blocked until it begins a new transaction. If a DHCP NAK can be sent, the DHCP client will initiate a new transaction after each NAK (i.e. DHCP Discover), meaning FreeRADIUS will process each DHCP Discover from the client, and the block will be removed much closer to the desired block time. Tue Jun 3 03:00:57 2014 : Debug: (3) rest : Sending HTTP GET to "http://xxxxxx//api/v1/dhcp/80%3Aea%3A96%3A2a%3Ab6%3Aaa" Tue Jun 3 03:00:57 2014 : Debug: (3) rest : Processing response header Tue Jun 3 03:00:57 2014 : Debug: (3) rest : Status : 401 (Unauthorized) Tue Jun 3 03:00:57 2014 : Debug: (3) rest : Skipping attribute processing, no body data received Tue Jun 3 03:00:57 2014 : Debug: rlm_rest (rest): Released connection (4) Tue Jun 3 03:00:57 2014 : Debug: (3) modsingle[authorize]: returned from rest (rlm_rest) for request 3 Tue Jun 3 03:00:57 2014 : Debug: (3) [rest.authorize] = fail Tue Jun 3 03:00:57 2014 : Debug: (3) } # dhcp DHCP-Discover = fail Tue Jun 3 03:00:57 2014 : Debug: (3) Finished request 3. Tue Jun 3 03:00:57 2014 : Debug: Waking up in 0.2 seconds. Tue Jun 3 03:00:58 2014 : Debug: Waking up in 4.6 seconds. Received DHCP-Discover of id 7b0fb2de from 172.19.0.9:67 to 172.19.0.12:67 Tue Jun 3 03:00:59 2014 : Debug: (3) No reply. Ignoring retransmit. Tue Jun 3 03:00:59 2014 : Debug: Waking up in 2.9 seconds. Received DHCP-Discover of id 7b0fb2de from 172.19.0.9:67 to 172.19.0.12:67 Tue Jun 3 03:01:02 2014 : Debug: (3) No reply. Ignoring retransmit. Tue Jun 3 03:01:02 2014 : Debug: Waking up in 0.4 seconds. Tue Jun 3 03:01:02 2014 : Debug: (2) Cleaning up request packet ID 2064626397 with timestamp +56 Tue Jun 3 03:01:02 2014 : Debug: Waking up in 1999991.0 seconds. Received DHCP-Discover of id 7b0fb2de from 172.19.0.9:67 to 172.19.0.12:67 Tue Jun 3 03:01:06 2014 : Debug: (3) No reply. Ignoring retransmit. Tue Jun 3 03:01:06 2014 : Debug: Waking up in 3999983.1 seconds. Received DHCP-Discover of id 7b0fb2de from 172.19.0.9:67 to 172.19.0.12:67 Tue Jun 3 03:01:15 2014 : Debug: (3) No reply. Ignoring retransmit. Tue Jun 3 03:01:15 2014 : Debug: Waking up in 7999966.3 seconds. Received DHCP-Discover of id 7b0fb2de from 172.19.0.9:67 to 172.19.0.12:67 Tue Jun 3 03:01:23 2014 : Debug: (3) No reply. Ignoring retransmit. Tue Jun 3 03:01:23 2014 : Debug: Waking up in 15999942.1 seconds.

    Read the article

  • Apache URL rewriting in reverse proxy

    - by Jeremy Gooch
    I'm deploying Apache in front of a Karaf-hosted application (Apache and Karaf are on separate servers). I want Apache to operate as a reverse proxy and also to hide part of the URL. The URL to get the log-in page of the application directly from the app server is http://app-server:8181/jellyfish. Pages are served by the Jetty instance running within Karaf. Of course, this behaviour would usually be blocked by the firewall for everything except the reverse proxy server. With the firewall off, if you hit this URL then Jetty loads the log-in page. The browser's address bar correctly changes to http://app-server:8181/jellyfish/login?0 and everything works. What I want is for http://web-server (i.e. from the root) to map to Jetty on the app server with the name of the app (jellyfish) suppressed. e.g. The browser would change to show http://web-server/login?0 in the address bar and all subsequent URLs and content would be served with the web-server's domain and without the jellyfish clutter. I can get Apache to operate as a simple reverse proxy, using the following config (snippet):- ProxyPass /jellyfish http://app-server:8181/jellyfish ProxyPassReverse / http://app-server:8181/ ...but this requires the browser's URL to contain jellyfish and going to the root URL (http://web-server) gives a 404 Not Found. I've spent a lot of time trying to use mod_rewrite with and without its [P] flag to get around this, but without success. I then tried the ProxyPassMatch directive, but I can't seem to get that quite correct either. Here's the current config, as is loaded into /etc/apache2/sites-available/ on the web server. Note that there is a locally-hosted images directory. I've also kept the mod_rewrite proxy exploit protection and am suppressing a couple of mod_security rules that were giving false positives. <VirtualHost *:80> ServerAdmin admin@drummer-server ServerName drummer-server ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined Alias /images/ "/var/www/images/" RewriteEngine On RewriteCond %{REQUEST_URI} !^$ RewriteCond %{REQUEST_URI} !^/ RewriteRule .* - [R=400,L] ProxyPass /images ! ProxyPassMatch ^/(.*) http://granny-server:8181/jellyfish/$1 ProxyPassReverse / http://granny-server:8181/jellyfish ProxyPreserveHost On SecRuleRemoveById 981059 981060 <Directory "/var/www/images"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order allow,deny Allow from all </Directory> </VirtualHost> If I go to http://web-server, I get redirected to http://web-server/jellyfish/home but this gives a 404, with a complaint about trying to access /jellyfish/jellyfish/home - NB the browser's address bar does not contain the double /jellyfish. HTTP ERROR 404 Problem accessing /jellyfish/jellyfish/home. Reason: Not Found And, if I go to http://web-server/login, I get redirected to http://web-server/jellyfish/login?0 but this gives a 404, with a complaint about trying to access /jellyfish/jellyfish/login. HTTP ERROR 404 Problem accessing /jellyfish/jellyfish/login. Reason: Not Found So, I'm guessing I'm somehow passing through the rules twice. I am also slightly bemused as to where the home bit of the URL comes from in the first example. Can someone point me in the right direction, please? Thanks, J.

    Read the article

< Previous Page | 238 239 240 241 242 243 244 245 246 247 248 249  | Next Page >