Search Results

Search found 8048 results on 322 pages for 'partial upgrade'.

Page 243/322 | < Previous Page | 239 240 241 242 243 244 245 246 247 248 249 250  | Next Page >

• external drive enclosure -> software RAID 5?

  - by memilanuk

  Hello all, I have two older PCs on my LAN posing as 'servers'... one running FreeNAS off a USB stick using three 500GB hdds in a ZFS RAID-Z pool serving as storage for the LAN and one running Debian Lenny with an 80GB drive used as a general purpose 'tinker' box that I can ssh into, etc. Problem is that the SMART report for one of those 500GB drives in the FreeNAS box is showing some pre-failure attributes, and the whole array is a little small anyways. Rather than simply replace one 500GB drive with another 500GB drive, and have no backup of the file server, I'd like to upgrade all the drives to 2TB ones - but I have no where to store that much data in the mean while. As such, I started looking at getting a 4-bay external drive enclosure with an eSATA card for the Debian box, with the hopes of creating a RAID5 + LVM setup using those drives and backing the data up to that external drive enclosure. After the backup is done, replace the drives in the FreeNAS box and rebuild the array there and mirror the data back. Then, I'd have both the primary storage (on the FreeNAS box) and a backup (which I don't have currently) using the external drive enclosure on the Debian box. My big question is... most of these external drive boxes seem to claim support for JBOD, RAID 0, 1, 10, 5, etc. - should I presume that is simply fake RAID like many commodity mobos have, and not really usable in Linux? In that case, with all the drives hanging off the one eSATA connection, will Linux (specifically Debian Squeeze, as I plan on upgrading that box here shortly) see all four drives, or just the first one? Will I be able to configure them in a RAID5 array as desired? Thanks, Monte

  Read the article

• PHP running too slow, always showing "504 Gateway Time-out"

  - by komase

  PHP running too slow, always showing "504 Gateway Time-out" My server spec: Dual core ATOM 330 CPU 2GB RAM Use nginx with PHP in fastcgi use eaccelerator CPU 74.3%id RAM used: 350MB of 2GB I have lots of sites in my server, with cron running every minutes all time, even on some minutes, double or triple cron running at same time. All my sites cron is heavy, usually the cron running more than one minutes. my nginx.conf has become too big until nginx refuse to start because too many sites in it. it has been solved by increasing server_names_hash_max_size. Im planning to add more sites in my server Now, opening my website always showing 504 Gateway Time-out. I have tested many eaccelerator and PHP setting, but this 504 Gateway Time-out still happen. the 504 Gateway Time-out will dissappeared when cron is disabled I have no idea: is this because not enough processor power? And what should I do? upgrade my processor? --------added this is top for my CPU just now: Cpu(s): 17.5%us, 3.8%sy, 0.1%ni, 71.6%id, 6.9%wa, 0.1%hi, 0.1%si, 0.0%st

  Read the article

• How do I host multiple independent, secured SharePoint sites (WSS 3.0) without using Active Director

  - by Kyle Noland

  I have a SharePoint site set up on one of my networks to service Active Directory users. To be clear, this is a Windows SharePoint Services 3.0 installation running on Windows Server 2003 Standard. It is not an option to upgrade the server or SharePoint version. Management would like to create several new sites, one for each of a handful of clients. These sites will be used like "dropboxes" or FTP sites so that my company can make large files available to outside contacts, and vice versa. Here are my requirements: I do not want to have to create Active Directory accounts for each external contact. If possible, I would like to store the external usernames and passwords in a database that I can write a small GUI for so that management can handle adding their own external contacts. Each client site must be sandboxed from each other and from my main company SharePoint site. I would like to keep everything running on port 80 and be able to access the sites as either clientname.mycompany.com or www.mycompany.com/clientname If anybody has ever done this I would really appreciate hearing about any lessons you learned and suggestions for how to set this up. Kyle

  Read the article

• PHP Startup: Unable to load dynamic library 'C:"\php\php_mysql.dll' - The specified module could not be loaded

  - by Tiny

  I'm trying to upgrade php 5.4.14 from php 5.4.3 in wamp server 2.2e. I have downloaded php-5.4.14-Win32-VC9-x86 (thread safe). Extracted it under C:\wamp\bin\php. Copied wampserver.conf from C:\wamp\bin\php\php5.4.3 to C:\wamp\bin\php\php5.4.14. Renamed php.ini-development to phpForApache.ini. -The port number the wamp server has been changed in the http.conf file to 8087 from its default 80. This is mentioned here though it is about upgrading from php 5.3.5 to php 5.4.0. After this, Restarting of the wamp server and services all over again has all been done and those two versions appeared in the menu php-versions (which is opened when the icon of the server is clicked). But when I attempt to enable a library like php_mysql or php_mysqli, a warning message box appears. PHP Startup: Unable to load dynamic library 'C:"\php\php_mysql.dll' - The specified module could not be loaded. I have also tried to removing the semicolon before them in the php.ini file but to no avail. I'm running Microsoft Windows XP Professional Version 2002, service pack 3. Where might be the problem? EDIT: I have changed extension_dir from C:\php to c:\wamp\bin\php\php5.4.14\ext\ in php.ini as the answer below indicates and the library is now loaded correctly but it says, 1045 - Access denied for user 'root'@'localhost' (using password: YES) though the user name and the password are the same as they are in MySQL in the config.inc.php file under phpmyadmin. I have also tried to restart MySQL56 service from Control Panel-Services(Local) but it keeps giving the same error. Does someone know why this happens?

  Read the article

• InterVLAN routing on a HP V1910 series switch

  - by tintix

  Recently bought a HP V1910-16G switch (former 3com 29??) with IPv4 routing capabilities. After unpacking I did a firmware upgrade to the latest 5.20 Release 1513P06. I did set up additional VLANs (#2 and #3) and VLAN interfaces for those. The problem is that connected PCs on different VLAN's can't ping each other. Looks like VLAN routing doesn't even work. So here's my setup: VLAN ID VLAN interface 1 10.0.0.21/24 2 10.0.5.1/24 3 10.0.6.1/24 Have one PC connected to VLAN 2 (IP address 10.0.5.2, default gateway 10.0.5.1) and a second PC connected to VLAN 3 (IP address 10.0.6.2, default gateway 10.0.6.1) Routing table: Destination IP Mask Next Hop 0.0.0.0 0.0.0.0 10.0.0.1 10.0.0.0 255.255.255.0 10.0.0.21 10.0.0.21 255.255.255.255 127.0.0.1 10.0.5.0 255.255.255.0 10.0.5.1 10.0.5.1 255.255.255.255 127.0.0.1 10.0.6.0 255.255.255.0 10.0.6.1 10.0.6.1 255.255.255.255 127.0.0.1 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 255.255.255.255 127.0.0.1 The first PC can't ping the second PC one and vice versa. They only can ping their own gateways and that's all. What I'm doing wrong?

  Read the article

• How to speed up a HP M9517C

  - by Jen

  I bought a system with 8GB RAM, 1TB HD, Quad-Core AMD Phenom 9550, Nvidia Geforce 9300GE, 64-bit Windows Vista Machine. Bought it primarily because it was cheap and came with 25.5 inch screen. Problem: It's slow - if you can believe it. My Dell laptop 1525 is faster and more stable! I tried installing and dual-booting Linux Mint and ran into video and audio troubles. I need fast and stable and I'm going for awesome. Anyone have some suggestions on making this thing smoking hot? Vista is fine, but slows over time - suspect virus/spyware/etc.. But I need to use Photoshop, Fireworks, Dreamweaver, Illustrator. I've tried the alternatives and I just don't like them. When you've got deadlines looming you want to work with what you know. Also use Skype (and I had audio problems with it in Linux), gotomeeting, gotowebinar. Don't need MS Office. Tried VMWare, Virtualbox and again - I keep getting audio/video problems. I'd love someone's input on THEIR setup and how they got there. I'm sure I need to upgrade my video card, but what should I go to?

  Read the article

• iOS 6 in-app email does not send from within any app that supports it

  - by Joe Termine

  A strange problem -- Last night I upgraded to the final release of iOS 6 on my iPhone 4S and my iPad 2. When I open an app that allows you to send emails from within the app (e.g. adobe Reader, TurboScan, etc.) -- doesn't matter which one -- I am prompted with the email dialog from within the app, I can compose the message, but when I go to send one of two things will happen: either the email sending sound will "swoosh" and the dialog will close (leading me to think it worked) or some apps with good error handling will say there is an "error sending email." The error logs on my device are not reporting errors. It's just that the email doesn't really send. I have two Exchange mail boxes on these devices. One connects to a corporate network hosting on-premise exchange 2007 and the other connects to Gmail over the exchange interface. Have attempted to delete and re-pair these accounts (one at a time) without any change. I'm wondering if others are experiencing this problem, or whether I should just wipe the devices and chalk it up to (another) failed upgrade. Thoughts much appreciated. Joe

  Read the article

• How do I host multiple independent, secured SharePoint sites (WSS 3.0) without using Active Directory on the same server?

  - by Kyle Noland

  I have a SharePoint site set up on one of my networks to service Active Directory users. To be clear, this is a Windows SharePoint Services 3.0 installation running on Windows Server 2003 Standard. It is not an option to upgrade the server or SharePoint version. Management would like to create several new sites, one for each of a handful of clients. These sites will be used like "dropboxes" or FTP sites so that my company can make large files available to outside contacts, and vice versa. Here are my requirements: I do not want to have to create Active Directory accounts for each external contact. If possible, I would like to store the external usernames and passwords in a database that I can write a small GUI for so that management can handle adding their own external contacts. Each client site must be sandboxed from each other and from my main company SharePoint site. I would like to keep everything running on port 80 and be able to access the sites as either clientname.mycompany.com or www.mycompany.com/clientname If anybody has ever done this I would really appreciate hearing about any lessons you learned and suggestions for how to set this up. Kyle

  Read the article

• Performance of Virtual machines on very low end machines

  - by TheLQ

  I am managing a few cheap servers as my user base isn't large enough to get much more powerful servers. I also don't have the money lying around to invest in a server to prepare for the larger user base. So I'm stuck with the old hardware I have. I am toying with the idea of virtualizing all the current OS's with most likely VMware vSphere Hypervisor (AKA ESXi) Xen (ESXi has too strict of an HCL, and my hardware is too old). Big reasons for doing so: Ability to upgrade and scale hardware rapidly - This is most likely what I'll be doing as I distribute services, get a bigger server, centralize (electricity bills are horrible), distribute, get a bigger server, etc... Manually doing this by reinstalling the entire OS would be a big pain Safety from me - I've made many rookie mistakes, like doing lots of risky work on a vital production server. With a VM I can just backup the state, work on my machine, test, and revert if necessary. No worries, and no OS reinstallation Safety from other factors - As I scale servers might go down, and a backup VM can instantly be started. Various other reasons. However the limiting factor here is hardware. And I mean very depressing hardware. The current server's run off of a Pentium 3 and 4, and have 512 MB and 768 MB RAM respectively (RAM can be upgraded soon however). Is the Virtualization layer small enough to run itself and a Linux OS effectively? Will performance be acceptable (50% CPU overhead for every operation isn't acceptable)? Does it leave enough RAM for the Linux OS? Is this even feasible?

  Read the article

• Upgrading from SQL2000 database to SQL Express 2008 R2

  - by itwb

  Hi, We have a web application which uses a MSSQL 2000 backend database. We are currently paying a ridiculous amount for Shared Hosting, with the database costs alone costing us $150 per month (MSSQL 100mb extra space is $40 per month). Our database size is 896.38 MB I am looking at getting a Virtual Private Server and upgrading the database to a MSSQL2008 Express database. I am aware that the Express version is limited to a 10GB database (with R2), and is constrained to a single CPU. I have also been offered SQL Server 2008 Web Edition for $19/per month, but I cannot find many details on the difference between Express and Web. Any suggestions here? What I would also like to know is: If we upgrade the database to MSSQL 2008 database, is there any issues with possible data transformations in the future? I.e. Is it possible to download and mount it with SQL Server 2008 Standard edition? I'm more concerned about how to get data in and out of the database through SQL Management tools. Are there any other issues that I might face? Thanks, Mike

  Read the article

• Nagios NTP, discarding peer

  - by picca

  We're using nagios *check_ntp_time* for monitoring time on our servers. Unfortunately the service is flapping. And reporting a lot of false-positives. It happens everytime for random server in random day time and lasts for ~10-30 minutes. When the problem occurs we get: watch01:~ # /usr/lib/nagios/plugins/check_ntp_time -H lb01 -w 1 -c 2 -v sending request to peer 0 response from peer 0: offset 0.07509887218 sending request to peer 0 response from peer 0: offset 0.07508444786 sending request to peer 0 response from peer 0: offset 0.07499825954 sending request to peer 0 response from peer 0: offset 0.07510817051 discarding peer 0: stratum=0 overall average offset: 0 NTP CRITICAL: Offset unknown| When everything is ok, we get (I used different server to not have to wait): watch01:~ # /usr/lib/nagios/plugins/check_ntp_time -H web02 -w 1 -c 2 -v sending request to peer 0 response from peer 0: offset 0.0002282857895 sending request to peer 0 response from peer 0: offset 0.0002194643021 sending request to peer 0 response from peer 0: offset 0.0002347230911 sending request to peer 0 response from peer 0: offset 0.0002293586731 overall average offset: 0.0002282857895 NTP OK: Offset 0.0002282857895 secs|offset=0.000228s;1.000000;2.000000; We are using: check_ntp_time v1.4.15 (nagios-plugins 1.4.15) on Debian squeeze. Remote ntp daemon is: ntpd - NTP daemon program - Ver. 4.2.4p4 I already found some forums where the problem is described: 1, 2, 3. Every time they edvise to upgrade nagios-plugins, because in version prior to 1.4.13 there was a bug with inserted leap second. But we have already newer version of nagios-plugins.

  Read the article

• iSCSI SAN Implementation with several ESXi hosts and two Equallogic SANs

  - by Sergey

  I work for a small state college. We currently have 4 ESXi hosts (all made by Dell), 2 EqualLogic SANs (PS4000 and PS4100) and a bunch of old HP Procurve switches. The current setup is very far from being redundant and fast so we want to improve it. I read several threads but get even more confused. The Procurve Switches are 2824. I know they don't support Jumbo Frames and Flow Control at the same time, but we have plans to upgrade to something like Procurve 3500yl. Any suggestions? I heard Dell Powerconnects 6xxx are pretty good but I'm not sure how they compare to HPs. There will be a 4-port Etherchannel (Link Aggregation) between the switches, and all control modules on SAN will be connected to different switches. Is there anything that will make the setup better? Are there better switches then Procurves 3500yl that cost less than 5k? What kind of bandwidth can I expect between ESXi hosts (they will also be connected to 2824 with multiple cables) and SANs?

  Read the article

• How do I increase maximum attachment size in Exchange 2007 SP1?

  - by AspNyc

  I've been looking all over for a relatively simple answer to a fairly straightforward question: "how do I increase the maximum size of attachments that can be sent and/or received in Exchange 2007?". But I have yet to find a solution that works. We have a pretty straightforward setup: Exchange 2007 SP1 running on a single server, with the OWA role delegated to a second server. We did a clean install of Exchange 2007 a year or two ago: we did not upgrade from a previous version. I forget if we installed RTM and then patched it to SP1, or if we installed with SP1 already baked in. I just thought I'd mention those items, in case they influence the answer. So far, I've tried running the following Powershell commands on the main Exchange server and verified that they've taken effect: Set-TransportConfig -MaxReceiveSize 40MB Set-ReceiveConnector "RcvConnector" -MaxMessageSize 40MB Set-MaxReceiveSize "MailboxName" -MaxReceiveSize 40MB As of right now, though, the specified mailbox is still rejecting messages over 10MB. You get brownie points if you can also tell me how to set the default mailbox attachment size limits, so that new accounts don't have default Set-MaxReceiveSize values of "unlimited" they currently do. Any advice or suggestions would be greatly appreciated. Tx in advance!

  Read the article

• Win Server 2k and Win 7 client

  - by Ray Kruse

  I have a Win Server 2000 system with AD configured. The network consists of an OKI printer, a network server, a wifi router a Win 2k client and the server. I'm trying to connect a Win 7 client. The purpose of the network, besides sharing equipment is to move files from client to client and scatter backups over more than 1 machine. The Win 7 client is configured for DHCP and does in fact receive it's IP and DNS configuration from the server and it sees the printer, wifi router and network drive, but does not see the Win 2k client nor the Win 2k server. I have tried the LAN Management Authentication Level set to 'Send LM & NTLM responses' with the 128 bit encryption removed. I've also done the registry hack on the key 'LmCompatibilityLevel'. Neither of these have helped. I have two questions: Is there a fix or is Win 2k totally incompatible? Is the best (or quickest/cheapest) fix to upgrade the server to Win 2k3 and not worry about the Win 2k client? Thanks for any help. Ray Kruse Buffalo, KY

  Read the article

• Lag in Windows 7 with Zepto Znote 6224W

  - by Xink64

  Hi! Why does my Zepto Znote 6224W Laptop with Windows 7 make these small laggy moves whenever I use it? First I installed Windows 7 64 bit because of the memorycap in Windows 7 32 bit, but soon I realized that the system was lagging randomly. It was very annoying whenever I listened to music, because of the sudden lags. Then I tried everything with drivers; Chipset, Soundcard, Graphicscard, and so on. No luck. I then installed Windows 7 32 bit and this reduced the amount of lags but they are still here. I haven't tried bios upgrade since my bios should be newest according to now the now bankrupt Zepto company. My specifications: Zepto Znote 6224W Intel T8300 Intel Chipset PM965 PC-5300 4gb Nvidia 8600M GT Zepto's rebranded bios: Phoenix Technologies LTD Z14ND06 - Date: 12/20/2007 Harddrive: 320 GB 5400 RPM which I replaced with a Kingston SSDnow 40 GB. No luck either. I haven't tried Windows Vista on the machine though, but I would like to keep Windows 7.

  Read the article

• Update BIOS on Sun Fire X4150 server

  - by Massimo

  I have some Sun Fire X4150 servers with a very old BIOS release (1ADQW015), which seems to have some compatibility problems with WMware ESX Server 3.5 and Windows 2008 R2 virtual machines; so I want to update the BIOS on them. The problem: according to this page, if your servers run ELOM (mine do), you first need to update to the latest ELOM release, then to the interim transition release, then finally you can update to the latest one. Ok, I'm willing to do that... but it looks like Sun (now Oracle) will happily let you download the latest firmware DVD (3.3.0), but it will not let you download the transition release (2.0) if you don't have a support contract. Well, I actuall don't care at all about the servers' management controllers (we don't even use them), so upgrading from ELOM to ILOM is totally irrelevant to me; but I need to update the servers' BIOS. So my question is: can I update the servers' BIOS to the latest version without doing the full ELOM-to-ILOM migration, or will this not work (or even make the servers unusable)? Do BIOS versions and SP ones need to be matched, or can one be updated without bothering with the other? Bonus question: if this whole ELOM-to-ILOM thing actually is needed in order to update the BIOS, can that 2.0 CD-ROM be obtained without having a support contract with Sun/Oracle (which we are definitely not going to sign, being that quite old hardware)? Update: I tried upgrading only the BIOS on one of the servers, and it didn't boot anymore. So it really looks like a full firmware upgrade is needed, and the management controller and BIOS versions should be kept in sync. So... where can I find that *&!£%$% 2.0 CD-ROM? Or at least the transition firmware that can be found on it?

  Read the article

• Windows 7 - system error 5 problem

  - by Ian

  My wife has just had a new computer for Christmas (with an upgrade from VISTA to Windows 7), and has joined the home network. We are using a mix of WindowsXP and Ubuntu boxes linked via a switch. We are all in the same workgroup. (No domain). Internet access, DHCP, and DNS server is an SME server that thinks it is domain controller (although we are not using a domain). I need to run a script to back up my wife's machine (venus). In the past the script creates a share on a machine with lots of space (leda), and then executes the line. PSEXEC \\venus -u admin -p adminpassword -c -f d:\Progs\snapshot.exe C: \\leda\Venus\C-drive.SNA With the wife's old XP machine, this would run the sysinternals utility, copy shapshot,exe to her machine and run it, which would then back up her C: drive to the share on leda. I cannot get this to work with Windows 7, nor can I link through to the C$ share on her machine. This gives me a permissions error (system error 5). The admin account is a full admin account. And yes - I do know the password. The ordinary shares on her machine work fine! I guess I'm missing something that Microsoft have built into Windows 7 - but what? The machine is running Windows 7 business, with windows firewall, AVG anti virus, and all the crap-ware you get with a new PC removed. Thanks

  Read the article

• Intermittent unavailability of an instance in a failover cluster while a standby node is offline in

  - by Emil Fridriksson

  Hi everyone. I've got a small failover cluster that I run for the websites my company has. During a RAM upgrade of the standby server, our websites started to show errors about not being able to access the database server. I verified that the instance was indeed up and the server accessable via remote desktop. I also tried a SQL connection to it and it worked, but that might have been after it became available again. This happened on and off until we were able to roll back the hardware changes that were in progress on the standby server and we were able to bring it back up. There was nothing of interest in the SQL Server log, but there is a continous log for the whole duration of the problem, so there was no restart of the SQL Server service. The event viewer is of more interest, since it shows events relating to the heartbeat network card, but I don't know how that would affect the availability of the server, since the standby node is offline. I'd appreciate any help you can provide, it's not very redundant if the setup depends on the standby server being up. :) Here are the event logs from the time of the problem, I include all of them since I can't seem to see what could possibly be the cause of the problem. Event log: http://hlekkir.com:800/htmltable.htm

  Read the article

• nVidia performance with newer X and newer driver abysmal with Compiz

  - by Nakedible

  I recently upgraded Debian to Xorg 2.9.4 and installed nvidia-glx from experimental, version 260.19.21. This was somewhat of an uphill battle as the dependencies for the experimental nvidia-glx package are still somewhat broken. I got it to work without forcing the installation of any packages and without modifying the packages. However, after the upgrade compiz performance has been abysmal. I am using the desktop wall plugin and switching viewports is really slow - takes a few seconds for each switch. In addition to this, every effect that compiz does, such as zoom animations for icons when launching applications, takes seconds. The viewport switching speed changes relative to the amount of windows on that virtual screen - empty screens switch almost at normal speed, single browser windows work almost decently, but just 4 rxvt terminals slows the switches down to a crawl. My compiz configuration should be pretty basic. Xorg is likewise configured without anything special - the only "custom" configuration is forcing the driver name to be "nvidia". I've fiddled around with the nvidia-settings and compizconfig trying different VSync settings, but none of those helped. My graphics card is: NVIDIA GPU NVS 3100M (GT218) at PCI:1:0:0 (GPU-0). This is laptop GPU that is from the Geforce GTX 200 series. Graphics card performance should naturally be no problem.

  Read the article

• Confused about the Windows 7 Preinstallation Kit

  - by David Brown

  I build custom PCs and would like to use the Windows 7 Preinstallation Kit to make installation go a little quicker and customize the Windows image. However, since each PC is built to a particular customer's specifications, the hardware will rarely be the same. So, I would like to have a single answer file that will work for everything. I'm not sure if that's possible, however. What I mostly want to do for now is add my support information as well as pre-set anything that I would normally change after each installation completes. I have a Windows 7 Professional Upgrade DVD set (both 32-bit and 64-bit), but no OEM disks. I copied the Install.wim file to my local drive and opened it in the Windows System Image Manager, but it asks me to choose a catalog file specifically for each edition of Windows 7. Will this limit the answer file to whichever edition I choose? I would think choosing Starter would give me the most basic settings, which would apply to all other editions, but I'm not entirely sure of this. I don't intend to install any extra applications or drivers. I merely want to insert an OEM disk, my OPK USB drive, and have it work for whatever edition of Windows 7 I'm installing. If a large number of similarly-configured PCs need to be built, I'll go ahead and create a custom answer file in that case, but for a single machine order, that seems like overkill. In addition, do I need a separate answer file for 32-bit and 64-bit versions of Windows 7? Or will it work for both, even though I copied the Install.wim file from the 32-bit disk? Thanks!

  Read the article

• Ubuntu 11.10 Virtual-box Unity 3D not working

  - by naveen

  After struggling for four hours, I still cannot get Unity 3D of Gnome 3 to work on my VirtualBox - I have been pouring through Internet and forum posts but to no avail. Here's what I've done so far: VirtualBox 4.1.4r74921 on Windows 7 Installed Ubuntu Desktop 11.10 ( 32 bit ) Enabled 3D acceleration Allocated 1.5GB of RAM Allocated 50MB video memory (hope this is not the culprit) Installed Guest edition 4.1.4 Did apt-get update and apt-get upgrade Booted back in to Ubuntu - falls back to Unity 2D Shared folder, mouse integration all works, so guest edition is properly installed Tried the command and below is the output /usr/lib/nux/unity_support_test –p OpenGL vendor string: Mesa Project OpenGL renderer string: Software Rasterizer OpenGL version string: 2.1 Mesa 7.11 Not software rendered: no Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: no GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: no I am trying to find what the "no" means but cannot find any good answers. Inter Core i5 processor 4GB of RAM on the host Display adapter: NVIDIA GeForce 8400GS Is anyone else facing the same problem? If so, can you point me to a solution or any reference where I can find a solution?

  Read the article

• How do I switch java versions to an earlier version in Fedora 17?

  - by JHutson456

  I just installed Fedora 17. I'm setting up the Android Build Environment and need Java. I downloaded and installed jdk-6u32-linux-amd64.rpm I ran java -version and it spit out the correct version. Well a day or two later i tried my first compile in Fedora 17 and it complained about java and failed. I ran java -version again and low and behold it spits out $ java -version java version "1.7.0_03-icedtea" OpenJDK Runtime Environment (fedora-2.1.fc17.7-x86_64) OpenJDK 64-Bit Server VM (build 22.0-b10, mixed mode) I'm stumped. I mean, i've run the update/upgrade commands since i installed but i didn't think that updated full version revisions... So, I ran alternatives --config java and that only gave me the java 1.7 version. While digging around more I discovered that the recommended version of Java for the build environment is jdk-6u27-linux-x64-rpm.bin so I downloaded that from here: Oracle Download When I ran: sudo sh jdk-6u27-linux-x64-rpm.bin it returned: Unpacking... Checksumming... Extracting... UnZipSFX 5.50 of 17 February 2002, by Info-ZIP ([email protected]). inflating: jdk-6u27-linux-amd64.rpm inflating: sun-javadb-common-10.6.2-1.1.i386.rpm inflating: sun-javadb-core-10.6.2-1.1.i386.rpm inflating: sun-javadb-client-10.6.2-1.1.i386.rpm inflating: sun-javadb-demo-10.6.2-1.1.i386.rpm inflating: sun-javadb-docs-10.6.2-1.1.i386.rpm inflating: sun-javadb-javadoc-10.6.2-1.1.i386.rpm Preparing... ########################################### [100%] package jdk-2000:1.6.0_32-fcs.x86_64 (which is newer than jdk-2000:1.6.0_27-fcs.x86_64) is already installed Done. so now I'm confused. I ran: alternatives --config java again but it's still only returning 1.7 so I don't know what to do.I want to end up with 6u27 as the installed and functional version of the JDK. Thank you.

  Read the article

• How to avoid Windows Genuine Advantage for an XP update?

  - by hlovdal

  I am about to apply updates to a windows xp installation I have not booted in a couple of years. When going to update.microsoft.com, it forced me first to accept an activex installation and now it wants me to install wga: Windows Update To use this latest version of Windows Update, you will need to upgrade some of its components. This version provides you with the following enhancements to our service: <... useless list of "advantages" ... Details Windows Genuine Advantage Validation Tool (KB892130) 1.1 MB , less than 1 minute The Windows Genuine Advantage Validation Tool enables you to verify that your copy of Microsoft Windows is genuine. The tool validates your Windows installation by checking Windows Product Identification and Product Activation status. Update for Windows XP (KB898461) 477 KB , less than 1 minute This update installs a permanent copy of Package Installer for Windows to enable software updates to have a significantly smaller download size. The Package Installer facilitates the install of software updates for Microsoft Windows operating systems and other Microsoft products. After you install this update, you may have to restart your system. Total: 1.5 MB , less than 1 minute I have heard nothing but bad things about wga, and I absolutely do not want it installed on my system (this answer seems to give some options). Searching for "windows xp" at microsoft's web pages brought up this page which says Windows XP Service Pack 3 Network Installation Package for IT Professionals and Developers Brief Description This installation package is intended for IT professionals and developers downloading and installing on multiple computers on a network. If you're updating just one computer, please visit Windows Update at http://update.microsoft.com . ... File Name: WindowsXP-KB936929-SP3-x86-ENU.exe I am currently downloading this file. Will installing this bring my installation up to date with security updates? What about later updates whenever a new problem is discovered, how can i update without using wga?

  Read the article

• How do you verify a restore?

  - by Nic

  What tool(s) would you use to verify that a restored file structure is whole and complete? My environment is a Windows Server 2008 file server. (We use tape for backup, but that is inconsequential.) I am specifically looking for a tool that will: Record the names of all files and folders below a specified directory Optionally calculate checksums of each file encountered Save this index in a human-readable format Compare the index against restored data and show differences Some background: I recently had to replace the disks in our file server. The upgrade was scheduled to start 36 hours after the most recent full backup, so I created a differential backup. However, it turns out that one of our applications was clearing the archive bit on files saved to the server, so these were not included in the differential backup. I was unaware of this until my users reported some files as missing. Aside from this, are there any other common methods for validating the integrity of a restore? I am frequently told that testing backups by restoring them is the only way to know that backups are working, but how do you deal with the case where it works 99% correctly and the other 1% silently fails?

  Read the article

• Postfix not sending email after upgrading to Ubuntu 12.04

  - by Luke

  After upgrading a server from Ubuntu 10.04 to 12.04, postfix is no longer sending email through sendgrid.com. I followed this guide about 6 months ago and everything had been working perfectly until the upgrade. Now it doesn't seem to be authenticating with sendgrid. This is the error I get in my syslog when I try to send an email. May 22 10:19:55 server postfix/smtp[3844]: 983B11C5DA: to=<to address>, relay=smtp.sendgrid.net[174.36.32.204]:587, delay=0.05, delays=0.01/0/0.04/0, dsn=5.0.0, status=bounced (host smtp.sendgrid.net[174.36.32.204] said: 550 Cannot receive from specified address <sendgrid username>: Unauthenticated senders not allowed (in reply to MAIL FROM command)) This is from postconf -n alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_dot_mydomain = no biff = no broken_sasl_auth_clients = no config_directory = /etc/postfix header_size_limit = 4096000 inet_interfaces = loopback-only mailbox_size_limit = 0 mydestination = localhost, mylinode.members.linode.com myhostname = hostname mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 readme_directory = no recipient_delimiter = + relayhost = [smtp.sendgrid.net]:587 smtp_sasl_auth_enable = yes smtp_sasl_mechanism_filter = login smtp_sasl_password_maps = hash:/etc/postfix/sasl/sendgrid smtp_sasl_security_options = noanonymous smtp_tls_security_level = may smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_tls_cert_file = /etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes Any help would be greatly appreciated. I would be happy to post any other logs or other relevant information.

  Read the article

< Previous Page | 239 240 241 242 243 244 245 246 247 248 249 250  | Next Page >