Search Results

Search found 12705 results on 509 pages for 'ip routing'.

Page 244/509 | < Previous Page | 240 241 242 243 244 245 246 247 248 249 250 251  | Next Page >

• Is IPv6 multicast routable over the Internet?

  - by Absolom

  As I understand it, public IPv6 addresses allocated by the IANA will have the prefix 2000::/3. These ip addresses will be routable through the Internet. IPv6 multicast addresses on the other side are prefixed FF00::/8. So my understanding is that the ipv6 multicast addresses won't be routable through the internet. I am right? If so, is there any way to do one-to-many ip routing over the Internet in IPv6? Thanks!

  Read the article

• Connection closed by remote host followed by Connection refused

  - by Khosrow

  All of a sudden my ssh connection to server has been damaged. Here is what's happened: $ ssh -vvv -p <PORT> -l <USER> <HOST> OpenSSH_5.3p1 Debian-3ubuntu7, OpenSSL 0.9.8k 25 Mar 2009 debug1: Reading configuration data /home/khosrow/.ssh/config debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to <HOST> [<IP>] port <PORT>. debug1: Connection established. debug1: identity file /home/khosrow/.ssh/identity type -1 debug1: identity file /home/khosrow/.ssh/id_rsa type -1 debug1: identity file /home/khosrow/.ssh/id_dsa type -1 ssh_exchange_identification: Connection closed by remote host I've recently updated the box with yum update and sshd got updated as well. I honestly don't know if this caused any damages or not. But it's prompted that /etc/ssh/sshd_config was stored as /etc/ssh/sshd_config.rpmnew which was quite normal. I've seen similar posts while googling, but almost all of them suggests that I should check /etc/hosts.allow and /etc/hosts.deny, which in my case, I can't. I can not connect to the box to see what's going on there. I rebooted the box, through web interface of server provider, and it even got worse. I'm now getting this: $ ssh -vvv -p <PORT> -l <USER> <HOST> OpenSSH_5.3p1 Debian-3ubuntu7, OpenSSL 0.9.8k 25 Mar 2009 debug1: Reading configuration data /home/khosrow/.ssh/config debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to <HOST> [<IP>] <PORT>. debug1: connect to address <IP> port <PORT>: Connection refused ssh: connect to host <HOST> port <PORT>: Connection refused with both <CUSTOM_PORT> and default 22 ports. I would really appreciate if anyone could help me on this.

  Read the article

• Created a new zone in DNS manager - can't get site bindings to work in iis 7

  - by nick gowdy

  Firstly I would like to say that I am a noob when it comes to DNS, I am a web developer and I am trying to setup an intranet site for a charity. I have windows server 2008 and I installed both iis 7 and dns manager. In IIS I have this binding that works - Type: http:// IP Address: 192.168.1.9 Port: 80 Host name: My host name is empty and when I try to navigate to this website on the network, the http code is 200 and the page renders. Now if I try Host name of test.organization.intranet Internet explorer says "Internet Explorer cannot display the webpage" and the server response is aborted. In DNS manager I created a new forward lookup zone of organization.intranet I did this through the configure a dns server wizard and I created a host (A) with the same IP as the one being used in IIS. The full Host name is test.organization.intranet but it doesn't work. Maybe I am missing something obvious because it's not an area of IT that I know very well, but I am stuck for why I can't get it to work.

  Read the article

• IIS7 - multiple ports for websites, some working, some not.

  - by glasnt

  I have multiple IIS7 websites hanging off 1 IP, using different ports. All three sites use Z.A.B.C:XX, where XX is {100, 200, 300} * There's no web.config settings not making :300 not work, the bindings are set ok. I can even change the ports so 200 becomes 300, but the original 300 still doesn't work. They are all shown by IP, so it's not DNS. There's no SSL setting differences between them. I can't see anything in metabase.xml that would make one behave differently to another. Are there any other settings in IIS7 that I might not be finding, that would fix the issue? * not the real values.

  Read the article

• macports apache,php,db, how do I test on another device?

  - by brokenindexfinger

  My supervisor suggests using macports to install/manage different versions of apache and php, as well as both mysql and posgres databases. The idea is that we need to test our platform on different versions of each. So far I've just been using the default apache installation on osx lion, and the default postgres installation. My question is this: once I turn Web Sharing off, and proceed with a custom apache2 setup based in /opt/local/, how do I broadcast my machine's IP to other devices, for testing? With Web Sharing, I can get my machine's IP and use that to test with an iPad and iPhone. Will that still be the case, and if so, how do I do it?

  Read the article

• cannot using internet in VMWare

  - by user66247

  I am using VMware Workstation version 7 on Ubuntu 10.10. I installed Windows XP service pack 3 for guest os. Within VMWare, I am using bridge connection that I assigned static IP address to be able to ping host IP address but I cannot ping default router gateway. I also tried to command "/etc/init.d/vmware start" on terminal. All tasks are able to start successfully except "VM communication interface socket family" I am not sure that how to setup network for my VMWare by using wireless. Thanks in advance.

  Read the article

• Limiting to the ServerName in Apache2

  - by David

  I have 2 sites defined in my Apache2. Each one has a servername. For example: Server 1 (first in sites-enabled) responds to www.example.com Server 2 (second in sites-enabled) responds to www.example2.com Ok, the problem is when I type the server IP in the URL, the first server responds. How could I limit the response to only specifying its servername? I would like to block the IP calls. If that is not possible, I would like the second server to respond, not the first. I cannot change the order because there are aliases defined in the second server that would override the first server config.

  Read the article

• is using Hosts for resolving a sql-server more performant?

  - by Ice

  Hi, we have a legacy application which uses a access.mdb with hundreds of ODBC-connected tables on a sql-server. the access.mdb contains nothing else than these odbc-connections. Now we consider to use a virtual sql-servername for these odbc connections and resolve it in the local hosts-file with the ip-address of the real sql-server. Like this we can easy switch between a test-sql-database server and the the server for production in changing one single entry in the hosts. EVERYTHING works fine and now comes the question: Could it be that this is more performant because there is one single point on resolving the sql-server (name or ip-address)? Is there something like a network-cache / DNS-Cache? peace Ice

  Read the article

• Turn on PC power remotely through the Internet?

  - by W.N.

  I use SVN for my work at home and office, but I usually forget to commit the changes before shutdown. Therefore, I wish I could turn on my home/office PC at office/home. I already have TeamViewer installed on both PCs, so it will be okay as soon as the power is turned on. I have read many articles about this, I found both my PC and office computers support Wake-on-LAN. However, I don't know much about other config. And I need to turn on my computers through the Internet, not on LAN. My office Internet connection has static IP, however, my home Internet connection has dynamic IP, it changes as soon as I reset the modem, but it is not a big problem, I rarely turn the Internet modem off. And I don't have privilege to config office Internet connection, but I have Administration privilege on both PCs. Please give me details steps to turn on my office PC from home, and turn on my home PC from office.

  Read the article

• software to view logs on remote server

  - by Tarun

  I have configured syslog server on my linux machine like this Linux Machine (syslog client) -- Linux Machine (syslog server) I have configured it and its working properly. Now, the problem is I want to look at the logs located on remote server in a particular directory for example /var/log/host-ip/httpd.log. One way is that I use ssh for that and then see those logs using commands like tail etc. So is there any Browser based graphical utility which I can use on my machine in which I just give the remote folder location, ip-address etc. and the software shows me the logs present on that remote server. Thanks.

  Read the article

• Manage a lot of open ssh sessions to servers with id's for hostname

  - by kimausloos

  Lately I'm working a lot with a few open ssh connections to multiple VPS servers. The hostnames of the servers all follow an ID approach and it's becoming very difficult to know on what machine I'm working with. I was wondering if there is a way to put a name I define somewhere as the title of the terminal. So I would, for example, associate IP 123.123.123.123 with webserver-stg. When opening the connection to the IP, webserver-stg would automaticaly be displayed as the name of the session. Of course I'm not able to change code on the VPS servers, so the solution should be client-side.

  Read the article

• Mac Snow Leopard Server DNS

  - by panomedia

  I have a Tomcat-driven application on my Windows server that I am planning to move to a MacMiniServer. Before I do this, I want to fully test the transition for licensing purposes. I have a Fire drive setup with Snow Leopard Server and the base app runs just fine BUT I need to be able to resolve the URL to my domain and not localhost. So, I figured I would setup panomedia.net in the DNS Server and also create an A record to my internal network IP so www.panomedia.net would dish out the same thing as localhost. The problem is: The Tomcat web app starts up going through panomedia.local and not through www.panomedia.net and My main network preference panel is still looking at my Comcast DNS search providers even though I put my local IP address as the only DNS Server and Search provider. I need to test this via an actual domain name before I commit to a 400GB data move. Can anyone help?

  Read the article

• domain/IN: has no NS records

  - by thejartender

  I have set up a home web server using Ubuntu 12.10 and I can safely say that it works with regards to router forwarding and ports being found. I know this, because switched my hosting provider's VPS SOA record to use my ISP IP with an 'A' value and had my website running from home. This verified that my server was configured correctly so I started what I believe to be the final step in making my old desktop into a full DNS server. I found this tutorial that got me started My LAN network consists of the following: My router with a gateway of 10.0.0.zzz My server with an IP of 10.0.0.xxx A laptop with an IP of 10.0.0.yyy Step 1: I installed bind via sudo apt-get install bind9 Step2: I configured /etc/bind/named.conf.local with: zone "sognwebdesign.no" { type master; file "/etc/bind/zones/sognwebdesign.no.db"; }; zone "0.0.10.in-addr.arpa" { type master; file "/etc/bind/zones/rev.0.0.10.in-addr.arpa"; }; Step3: Updated /etc/bind/named.conf.options with two ISP DNS addresses Step 4: Updated /etc/resolv.confwith: nameserver 10.0.0.xxx search lan search sognwebdesign.no Step5: created a ``/etc/bind/zones directory Step6: Created /etc/bind/zones/sognwebdesign.no.dbwith: $TTL 3D @ IN SOA ns.sognwebdesign.no. admin.sognwebdesign.no. ( 2007062001 28800 3600 604800 38400 ); sognwebdesign.no. IN NS ns1.sognwebdesign.no. sognwebdesign.no. IN NS ns2.sognwebdesign.no. sognwebdesign.no. IN NS ns3.sognwebdesign.no. NS1 IN A 10.0.0.1 NS2 IN A 10.0.0.2 NS3 IN A 10.0.0.3 www IN A 10.0.0.4 yuccalaptop IN A 10.0.0.19 gw IN A 10.0.0.138 TXT "Network Gateway" Step 7: created/etc/bind/zones/rev.0.0.10.in-addr.arpawith: $TTL 3D @ IN SOA ns.sognwebdesign.no. admin.sognwebdesign.no. ( 2007062001 28800 604800 604800 86400 ); zzz IN PTR gw.sognwebdesign.no. 1 IN PTR ns1.sognwebdesign.no. 2 IN PTR ns2.sognwebdesign.no. 3 IN PTR ns3.sognwebdesign.no. yyy IN PTR yuccalaptop.sognwebdesign.no. I then restart bind and dig-x sognwebdesign.no and it works Lastly I perform named-checkzoneon each of my zone files, but me reverse zone fail fails with: sognwedesign.no/IN: has no NS records Can anyone explain what I am doing wrong here or assist me in getting this configured correctly?

  Read the article

• Can't access phpMyAdmin because of host, username and password

  - by Engprof

  everyone. When I try to access phpMyAdmin on Uniform Server I get the following error messages: " #1045 - Access denied for user 'root'@'localhost' (using password: YES) " " phpMyAdmin tried to connect to the MySQL server, and the server rejected the connection. You should check the host, username and password in your configuration and make sure that they correspond to the information given by the administrator of the MySQL server. " The funny thing is my username and password are both set to "root" and I have changed the IP address in the httpd.conf file to my Unique IP adddress, so I still don't know what the problem is. Could somebody please help me out? Any help would be much appreciated.

  Read the article

• Monitor torrent user in network [closed]

  - by Usman

  I am using active directory in windows server 2008 R2 having IP address is 10.10.10.10 and my DSL modem Ip is 10.10.10.101. All clients are using 10.10.10.101 default gw to access the Internet. I don't know who is using Torrent in network or downloading something via IDM or something else. I just want to Monitor my clients for who are download via torrent or whatever. Is there anything in Windows Server 2008r2 that would allow me to do this monitoring, or do I need something else?

  Read the article

• Amazon EC2 - Reserved Private Addresses

  - by reach4thelasers

  I've got a private DNS Server running on Amazon EC2. I don't need a public IP Address because its only used for private addressing web1.xxx.internal database1.xxx.internal Problem is I had to terminate the instance recently and start a new one. This meant that the private IP address of the DNS server changed and I had to log in to each of my other 15 server one-by-one and change the DNS address to point to the new DNS server. There must be a better way to do this, if so, what is it?

  Read the article

• Cant connect to home server

  - by user52141

  Trying to figure out what I might be doing wrong. I installed XAMPP - and everything looks fine. If I go to localhost everything comes right up. But when I go to my IP address, I just get a message that the browser could not connect to it. I go into my router and set up port forwarding for port 80 etc, and I even tried putting the server as a DMZ - still nothing. I turned the firewall off to see if that was interfering in some way, then uninstalled it completely for good measure, made no difference. I'm out of ideas.. oh, and yes I have a static IP address.

  Read the article

• Windows 7 system CPU bogged by windows services, no explanation

  - by Alex

  I'm looking at a laptop for a colleague which is running terribly slow. A quick look showed that the CPU was 100% used by 2-3 SVCHost processes, which off course doesn't tell much since those are just 'cover' processes with services running underneath them. So I fired up process explorer in hopes of finding a shady rogue service which was bogging the system, but to my suprise I found genuine MS Windows processes (or at least damn-good disguised ones) are bogging down the system: dnscache (DNS Client) IKEEXT (IKE and AuthIP IPSec Keyring modules) iphlpsvc (IP Helper) Seen separately, these processes might seem odd to be using a lot of CPU, but taking a step back one can conclude that all three services are quite closely related to networking. I've tried running: netsh int ip reset log.txt which has helped me save bizarre network-related problems in the past, but this didn't help Off course I though about a virus, but both MS Security Essentials as well as malwarebytes (let both run a full scan).

  Read the article

• Postgres Remote Access

  - by boot-baby-boot

  I am trying to connect to postgres remotely.I have followed this tutorial http://www.cyberciti.biz/faq/howto-fedora-linux-install-postgresql-server/ and have executed the following commands to see if the remote access is possible. [root@printmyworld ~]# egrep -i "(listen_addresses|port|tcpip_socket).*=.+" /var /lib/pgsql/data/postgresql.conf #listen_addresses = '*' # what IP address(es) to listen on; #port = 5432 [root@printmyworld ~]# lsof +c0 -anPiTCP -upostgres COMMAND PID USER FD TYPE DEVICE SIZE NODE NAME postmaster 9323 postgres 3u IPv4 2875987353 TCP 127.0.0.1:5432 (LISTEN ) postmaster 9323 postgres 4u IPv6 2875987354 TCP [::1]:5432 (LISTEN) I am suspicious of this line: postmaster 9323 postgres 3u IPv4 2875987353 TCP 127.0.0.1:5432 (LISTEN My server ip address is 1yy.000.1xx.000 .Should it be 1yy.000.1xx.000:5432

  Read the article

• connecting hostname to server

  - by Michael Ropy

  I have an ubuntu server installed on my server with virtualmin webmin. everything is good the server itself....I can connect to localhost and the virtualmin manager (http://localhost:10000). the problem is, I can't connect to it from a client computer. For example when I enter the IP address of the server, its shows me 403 forbidden error (sometimes its shows the homepage right)...but the virtualmin manager could not open... if my website is example.com with this ip: xxx.xxx.xxx.xxx, i can't connect to example.com:10000 or xxx.xxx.xxx.xxx:10000 what should I do?

  Read the article

• Wireshark Display Filter protocol==TLSV1? (and PacketLength)

  - by NealWalters

  What would the filter expression be to just select the protocols where the protocol = TLSV1? Something obvious like protocol == "TLSV1" or TCP.protocol == "TLSV1" is apparently not the right way. ip.proto == "TLSV1" says "ip.proto cannot accept strings as values" Update - additional tips: Another great but hidden search is on PacketLength: You can add packet length to your display by clicking "Edit Preferences" (menu or icon), and adding the PacketLength as a new column, but to filter on it you have to use the more cryptic: frame.len == ### where ### is your desired number. We were using this to determine how many packets had been sent and/or received, when you filter, the status-bar at the bottom of the screen shows the number of items matching the filter.

  Read the article

• How to forward traffic using iptables rules?

  - by ProbablePattern

  I am new to iptables and I have been doing Google searches for a few days now without finding a good solution to this problem. I have computer A with a public ip address (say 192.0.2.1) that can access the Internet unrestricted. I have another computer B with a private ip address (192.168.1.1) that can only access computer A. How do I use iptables to forward network traffic from B through A to the Internet? I need to use http, ftp, and https in order to use apt-get with sudo. Both computers run Ubuntu linux. I have tried using Squid but I think it is far too complicated for what I need to do.

  Read the article

• Cannot access internal network on OSX 10.6.6

  - by cabuki

  Last week, I began having trouble connecting to our internal web servers. Usually, a refresh would take care of it or switching to a different wireless network, but as of yesterday, this wasn't enough. We have an internal DNS server using dnsmasq and a private internal host name (us.lcl). Once I started having more issues with the names not resolving, I tried pinging the server. Using the internal host name (s1.us.lcl), it failed. I tried using the IP address, but that also failed. I have no problems accessing external sites with the exception of it being a bit slower than normal. A reboot yesterday at lunch time after following the instructions here seemed to fix the issue, but when I came into the office this morning, it had stopped working. As of this posting, I cannot ping, ssh or access the web server using the internal host name or ip address. I'm the only one running 10.6 in my office and none of my colleagues has this issue.

  Read the article

• Mirrored servers in data centers nationwide -- how?

  - by Sysadmin Evstar

  Mirrored servers in data centers nationwide -- how? I flunked my IT interview by getting this question wrong. I thought that in the various metropolitan areas, an "http://google.com" request goes to the ISP's DNS server, which somehow returns an IP address for one of several geographically-nearby http servers, and then something internally rolls over to the next available local Google server. But then, I could not explain where the table of available local Google servers is actually cached, or the details of the IP address rollover. Or how they could manually take some server out of the rotation, from anywhere. So, what should I be reading now so I can ace this question next time? Also, what daemons run on these machines 24/7 to keep all those mirrored database disks synchronized?

  Read the article

• Free firewall for Windows Server 2003

  - by n00b_Admin

  We have a Windows Server 2003 R2 Machine here at work that I need to ensure is accessible only from specific set of IP Addresses. The Server is on a LAN and I am aware that one of the possible solutions maybe limit access to the Server's VLAN. However that is not feasible at the moment. I've been searching for a firewall that could do this, Windows' Firewall is pretty limited and I don't see an option in it to limit incoming data based on Source IP addresses. Most free firewalls like Comodo and ZoneAlarm don't work on Windows Server. Any ideas on how to accomplish this would be of great help. Thanks in advance.

  Read the article

< Previous Page | 240 241 242 243 244 245 246 247 248 249 250 251  | Next Page >