Search Results

Search found 19471 results on 779 pages for 'network troubleshooting'.

Page 244/779 | < Previous Page | 240 241 242 243 244 245 246 247 248 249 250 251  | Next Page >

  • Gateway GT5220 Boot/POST Failure

    - by John Rudy
    I have a Gateway GT5220 I'm troubleshooting. It is, in fact, the machine I just gave my father for his birthday a couple months ago. (Prior to that, it was my home PC. My home PC is now the MacBook on which I'm writing this.) Before going any further, I suspect that the answer will be, "It's worse than that, it's dead, Jim, it's dead, Jim, it's dead, Jim." At least, mobo and/or CPU. The initial symptoms were as follows: Turn on power All fans fire up (thus making it so I can't hear if the hard drive is spinning or not, nor are my hands sensitive enough anymore to feel it) No LEDs remained lit on the front panel. (Initially, the hard drive indicator flashed briefly.) No beep, no video, no nothing. Following some advice I found here, I tried to "drain the stored power." After following those steps, the new symptoms were: Turn on power All fans fire up The front panel LEDs remained lit! After about 20, maybe 30 seconds, we had video! Sort of. We got to the Gateway splash/POST screen, which appeared thoroughly corrupted. How corrupted? Well, I imagine it's what a POST screen would look like after reading the wrong passage out of the Necronomicon: It stayed there. I gave it at least 5, maybe 6 minutes, and it didn't move. So I shut her down, started her up again, and now (this is where we currently stand, symptomatically) we have this: Turn on power All fans fire up The front panel LEDs remain lit No video, no beep, no nothing. I'm a software guy; haven't done real hardware troubleshooting in years. My gut tells me that the mobo and/or CPU is fried, and unfortunately my gut didn't get to be as big as it is being wrong all the time. :( In addition to the link above, I have read all of the following (trying to save you some LMGTFY trouble): Gateway Support POST Error Messages and Handling About a zillion (useless) POST beep code sites A kioskea.net post indicating that most likely we're at what I consider "total loss" (mobo and/or CPU) My questions: Are there any conditions other than mobo/CPU that could cause symptoms like these? Is it worth my time to try the next hardware troubleshooting step?(IE, remove all non-critical hardware from the machine, try to boot, systematically replace one by one until we find the failing component) Which mobos will fit in the Gateway GT5220 case (with rear ports correctly aligned)? (Why this is not a dupe: I wouldn't have posted this question if it hadn't been for the funkadelic possessed video display on the one occasion we got video out. I think that justified this not being an exact dupe. Of course, if the community overrules, I will understand.)

    Read the article

  • log in to v20z console using serial management

    - by conandor
    I have a Netra T1 (SPARC) which has LOM that enable to log in to the OS console locally for troubleshooting without plug in a monitor and keyboard. I also have a SunFire V20z (x86) which has a SP. However I do not find any equivalent command to reach the console. It would not be ideal for me to bring along monitor and keyboard to the data center for troubleshooting locally. For example, I accidentally messup the OS network configuration and unable to log in the OS. I have to log to the console through serial management/LOM to troubleshoot it. However it seem doesn't work in x86 machine. Is there anyway I can able to do the same thing on x86 machine?

    Read the article

  • IE and Chrome won't browse the internet on dial up but firefox will. How could I fix it?

    - by Kelbizzle
    First let me say I've done plenty of troubleshooting and will try to explain as clearly and as much as I can. Please bear with me. I have a client's computer who uses dial-up and Windows XP. The problem is when I connect to the dial up ISP. IE or Chrome will not browse the internet. It says page cannot be displayed. but if I use firefox on the dialup connection it works. Sounds simple enough there has got to be something wrong with the proxy settings or something...well, that's what I thought here is the weird part. When connected to the LAN in my office IE, Chrome, and FF all work. I upgraded to ie8 and the issue still happens. How would you go about troubleshooting this issue? What should I do next?

    Read the article

  • 'DNS server isn't responding' error in windows 7 home premium

    - by pradeeptp
    Hi All, I bought a brand new Dell Studio 1558 just last week. It has windows 7 home premium 64-bit installed on it. My friend who is occupying the adjacent room has a laptop with windows XP. Both of us are connecting to the same wireless router of the hotel. My friend is able to connect to the wireless network without any trouble, but when I try to connect, I get the error "DNS service isn't responding". I get this error when I run the troubleshooting option. I met two more people in the same hotel with win XP laptop and they too dont have any problem. I have gone to possibly all the forums and website but I haven't been able to fix this error :(. I have done all the basic troubleshooting but I have no luck yet. Pls help. Following is one forum where the problem seem to have been trouble shooted but not for all. http://social.technet.microsoft.com/Forums/en/w7itpronetworking/thread/eeb84518-903d-46d1-9398-80cf211878d7

    Read the article

  • Windows diagnostic tools

    - by Tathagata
    I just joined a small computer lab which basically uses all Windows boxes and a few Windows Sever 2003. Coming from a *nix background I am missing all the nice tools that we have for diagnosis and troubleshooting. My question is what are the safe, free (not terribly concerned if it is like beer or freedom -both acceptable) tools out there that Windows system admins use for their day to day troubleshooting (network, applications, servers etc). I am aware of the tools that come with Windows (and their limited capabilites) - so my query is with what do you fill in your arsenal? (may be a list of win versions of tools that come in standard linux distros)

    Read the article

  • New Communications Industry Data Model with "Factory Installed" Predictive Analytics using Oracle Da

    - by charlie.berger
    Oracle Introduces Oracle Communications Data Model to Provide Actionable Insight for Communications Service Providers   We've integrated pre-installed analytical methodologies with the new Oracle Communications Data Model to deliver automated, simple, yet powerful predictive analytics solutions for customers.  Churn, sentiment analysis, identifying customer segments - all things that can be anticipated and hence, preconcieved and implemented inside an applications.  Read on for more information! TM Forum Management World, Nice, France - 18 May 2010 News Facts To help communications service providers (CSPs) manage and analyze rapidly growing data volumes cost effectively, Oracle today introduced the Oracle Communications Data Model. With the Oracle Communications Data Model, CSPs can achieve rapid time to value by quickly implementing a standards-based enterprise data warehouse that features communications industry-specific reporting, analytics and data mining. The combination of the Oracle Communications Data Model, Oracle Exadata and the Oracle Business Intelligence (BI) Foundation represents the most comprehensive data warehouse and BI solution for the communications industry. Also announced today, Hong Kong Broadband Network enhanced their data warehouse system, going live on Oracle Communications Data Model in three months. The leading provider increased its subscriber base by 37 percent in six months and reduced customer churn to less than one percent. Product Details Oracle Communications Data Model provides industry-specific schema and embedded analytics that address key areas such as customer management, marketing segmentation, product development and network health. CSPs can efficiently capture and monitor critical data and transform it into actionable information to support development and delivery of next-generation services using: More than 1,300 industry-specific measurements and key performance indicators (KPIs) such as network reliability statistics, provisioning metrics and customer churn propensity. Embedded OLAP cubes for extremely fast dimensional analysis of business information. Embedded data mining models for sophisticated trending and predictive analysis. Support for multiple lines of business, such as cable, mobile, wireline and Internet, which can be easily extended to support future requirements. With Oracle Communications Data Model, CSPs can jump start the implementation of a communications data warehouse in line with communications-industry standards including the TM Forum Information Framework (SID), formerly known as the Shared Information Model. Oracle Communications Data Model is optimized for any Oracle Database 11g platform, including Oracle Exadata, which can improve call data record query performance by 10x or more. Supporting Quotes "Oracle Communications Data Model covers a wide range of business areas that are relevant to modern communications service providers and is a comprehensive solution - with its data model and pre-packaged templates including BI dashboards, KPIs, OLAP cubes and mining models. It helps us save a great deal of time in building and implementing a customized data warehouse and enables us to leverage the advanced analytics quickly and more effectively," said Yasuki Hayashi, executive manager, NTT Comware Corporation. "Data volumes will only continue to grow as communications service providers expand next-generation networks, deploy new services and adopt new business models. They will increasingly need efficient, reliable data warehouses to capture key insights on data such as customer value, network value and churn probability. With the Oracle Communications Data Model, Oracle has demonstrated its commitment to meeting these needs by delivering data warehouse tools designed to fill communications industry-specific needs," said Elisabeth Rainge, program director, Network Software, IDC. "The TM Forum Conformance Mark provides reassurance to customers seeking standards-based, and therefore, cost-effective and flexible solutions. TM Forum is extremely pleased to work with Oracle to certify its Oracle Communications Data Model solution. Upon successful completion, this certification will represent the broadest and most complete implementation of the TM Forum Information Framework to date, with more than 130 aggregate business entities," said Keith Willetts, chairman and chief executive officer, TM Forum. Supporting Resources Oracle Communications Oracle Communications Data Model Data Sheet Oracle Communications Data Model Podcast Oracle Data Warehousing Oracle Communications on YouTube Oracle Communications on Delicious Oracle Communications on Facebook Oracle Communications on Twitter Oracle Communications on LinkedIn Oracle Database on Twitter The Data Warehouse Insider Blog

    Read the article

  • Announcing the latest update to Oracle VM Server for x86 2.2 Release

    - by Honglin Su
    More and more customers have discovered that Oracle delivers more value with Oracle VM compared with other server virtualization solutions, and we've seen the momentum that customers succeed with Oracle VM and leading partners support Oracle VM. Recently, Oracle VM server for x86 with Windows PV Drivers passed Microsoft SVVP requirements for Windows servers, which provides customers more confidence to deploy Microsoft Windows guest OS onto Oracle VM server for x86. Today I'm pleased to announce the Oracle VM server for x86 2.2.2 release. See the new features introduced in the 2.2.2 release. Expand the guest OS support to include Oracle Linux 6.x and Oracle Solaris 11 Express OS. For a complete list of guest OS support, please refer to the Oracle VM server x86 release note. The VMPInfo system information and cluster troubleshooting utility is provided with this release. Additional information on VMPInfo is also available in the following My Oracle Support Notes: 1263293.1 Post-installation check list for new Oracle VM Server 1290587.1 Performing Site Reviews and Cluster Troubleshooting with VMPInfo A new storage repository option to provide NFS mount options when creating a storage repository. For more information on this new parameter, see Oracle VM Server User Guide "Adding a Storage Repository". Updated OCFS2 cluster file system, libdhcp, device drivers. See details and additional enhancements at Oracle VM Server User Guide: New Features in Release 2.2.2. The Oracle VM Server for x86 ISO image is available for download at Oracle's E-Delivery site. If you've subscribed to Oracle's Unbreakable Linux Network (ULN), you can simply run up2date command to update the server. Please refer to Oracle VM Upgrade Guide: Upgrading Oracle VM Server. There's no change to Oracle VM Manager, which remains at 2.2.0 with the patch 2.2-16. If you have any questions about Oracle VM Serer for x86, you may post your questions at OTN discussion forum; or purchase support for Oracle Unbreakable Linux and Oracle VM. For Oracle's x86 systems, Oracle VM support as well Oracle Linux and Oracle Solaris support are included in the Oracle Premier Support for Systems. For more information about Oracle's virtualization, visit oracle.com/virtualization.

    Read the article

  • Resolve Instructional Webcast Series — E-Business Suite Payables Period Close

    - by user793044
    Resolve Instructional Webcast Series — New Product Specific Troubleshooting Topics For E-Business we have coming up: Title: Resolve—Best Practices for E-Business Suite Payables Period Close Date: Nov 7, 2012 Time: 8:00 am MT - 3:00 pm GMT - 10:00 am Eastern - 8:30 pm India - 7:00 am Pacific This one-hour webcast shows you how to use 3 main recommendations: Period Close Helper – New Diagnostic to identify and resolve period close issues. Master Generic Datafix Diagnostic (MGD) usage in proactive/reactive mode. Recommended Patch Collection (RPC) uptake. This session will help customers to plan and complete their month on month period close activities successfully. Also, in approaching period close in a proactive way. It will assist in order to avoid last minute hassles and prevent delays in achieving the Period Close deadlines. Customers who are involved in the Payables period close activities (both Functional and Technical) will benefit most from the webcast. Join us. Leverage this opportunity to learn Support Best Practices that help you resolve the issues you face with your Oracle products. Oracle Support experts provide live demonstrations of proactive resources. You will see you how working proactively helps you work more efficiently—from using the right tools to providing the right information on Service requests—you can get answers faster. Register for sessions now Resolve—Troubleshooting Questions? Contact Oracle’s "Get Proactive" team today. WORK SMART. SOLVE FAST. RESOLVE.

    Read the article

  • July, the 31 Days of SQL Server DMO’s – Day 3 (sys.dm_exec_connections)

    - by Tamarick Hill
      The third DMV we will review is the sys.dm_exec_connections DMV. This DMV is Server-Scoped and displays information about each and every current connection on your SQL Server Instance. Lets take a look at some information that this DMV returns. SELECT * FROM sys.dm_exec_connections After reviewing this DMV, in my opinion, its not a whole lot of useful information returned from this DMV from a monitoring or troubleshooting standpoint. The primary use case I have for this DMV is when I need to get a quick count of how many connections I have on one of my SQL Server boxes. For this purpose a quick SELECT COUNT(*) satisfies my need. However, for those who need it, there is other information such as what type of authentication a specific connection is using, network packet size, and client/local TCP ports being used. This information can come in handy for specific scenarios but you probably wont need it very much for your day to day monitoring/troubleshooting needs. However, this is still an important DMV that you should be aware of in the event that you need it. For more information on this DMV, please see the below Books Online link: http://msdn.microsoft.com/en-us/library/ms181509.aspx

    Read the article

  • Get The Most From MySQL Database With MySQL Performance Tuning Training

    - by Antoinette O'Sullivan
    Get the most from MySQL Server's top-level performance by improving your understanding of perforamnce tuning techniques. MySQL Performance Tuning Class In this 4 day class, you'll learn practical, safe, highly efficient ways to optimize performance for the MySQL Server. You can take this class as: Training-on-Demand: Start training within 24 hours of registering and follow the instructor-led lecture material through streaming video at your own pace. Schedule time lab-time to perform the hands-on exercises at your convenience. Live-Virtual Class: Follow the live instructor led class from your own desk - no travel required. There are already a range of events on the schedule to suit different timezones and with delivery in languages including English and German. In-Class Event: Travel to a training center to follow this class. For more information on this class, to see the schedule or register interest in additional events, go to http://oracle.com/education/mysql Troubleshooting MySQL Performance with Sveta Smirnova  During this one-day, live-virtual event, you get a unique opportunity to hear Sveta Smirnova, author of MySQL Troubleshooting, share her indepth experience of identifying and solving performance problems with a MySQL Database. And you can benefit from this opportunity without incurring any travel costs! Dimitri's Blog If MySQL Performance is a topic that interests you, then you should be following Dimitri Kravtchuk's blog. For more information on any aspect of the Authentic MySQL Curriculum, go to http://oracle.com/education/mysql.

    Read the article

  • Don't Miss What Procurement Experts Are Talking About. Join the Webcasts starting next week!

    - by LuciaC
    The Procurement team have three Advisor Webcasts scheduled in December with information about new features, tips and tricks and troubleshooting guidance. New Features and enhancements Incorporated in the Procurement Rollup Patch 14254641:R12.PRC_PF.B December 4, 2012 at 14:00 London / 16:00 Egypt / 06:00 am Pacific / 7:00 am Mountain / 9:00 am EasternThis session is recommended for technical and functional users who need to know about the new features and enhancements incorporated in the Procurement Rollup Patch. Topics will include: GCPA Enable All Sites E-Mail PO - .LANGUAGE Read Only BWC Validate Document GBPA OSP Items GL Date Defaulting Cancel Refactoring Action History Cleanup Click here to register for this event. Approval Management Engine (AME) New Features, Setup and Use for Purchase Orders December 6, 2012 at 14:00 London / 16:00 Egypt / 06:00 am Pacific / 7:00 am Mountain / 9:00 am EasternThis is recommended for Functional Users and Application Technical Users who work in the Procurement Module including Purchasing and iProcurement and would like to know more about how to set up and use the Approval Management Engine (AME) for purchase orders.Topics will include: Scope and limitations of AME functionality for purchase orders Setup and use of AME for purchase orders PO Review and PO E-Sign new features Demonstration: Example of scenarios using the new features Click here to register for this event. How to Solve Approval Errors in Procurement December 18, 2012 at 4:00 pm Egypt / 2:00 pm London / 6:00 am Pacific / 7:00 am Mountain / 9:00 am EasternThis session is recommended for technical and functional users who need to know about how to diagnose and troubleshoot common Approval Errors.Topics will include: Basic mandatory setups for approvals of PO documents Differences between Purchase Order Approval and Requisition Approval Process. Troubleshooting of Approval Errors. Basic Setup of AME which can be used in Requisition Approval Process. Click here to register for this event. You can see a listing of all scheduled and archived webcasts from Doc ID 740966.1.  Select the product you are interested in (such as E-Business Suite Procurement) and this will take you to the webcast listing for the product.

    Read the article

  • InfiniBand Enabled Diskless PXE Boot

    - by Neeraj Gupta
    When you want to bring up a compute server in your environment and need InfiniBand connectivity, usually you go through various installation steps. This could involve operating systems like Linux, followed by a compatible InfiniBand software distribution, associated dependencies and configurations. What if you just want to run some InfiniBand diagnostics or troubleshooting tools from a test machine ? What if something happened to your primary machine and while recovering in rescue mode, you also need access to your InfiniBand network ? Often times we use opensource community supported small Linux distributions but they don't come with required InfiniBand support and tools. In this weblog, I am going to provide instructions on how to add InfniBand support to a specific Linux image - Parted Magic.This is a free to use opensource Linux distro often used to recover or rescue machines. The distribution itself will not be changed at all. Yes, you heard it right ! I have built an InfiniBand Add-on package that will be passed to the default kernel and initrd to get this all working. Pr-requisites You will need to have have a PXE server ready on your ethernet based network. The compute server you are trying to PXE boot should have a compatible IB HCA and must be connected to an active IB network. Required Downloads Download the Parted Magic small distribution for PXE from Parted Magic website. Download InfiniBand PXE Add On package. Right Click and Download from here. Do not extract contents of this file. You need to use it as is. Prepare PXE Server Extract the contents of downloaded pmagic distribution into a temporary directory. Inside the directory structure, you will see pmagic directory containing two files - bzImage and initrd.img. Copy this directory in your TFTP server's root directory. This is usually /tftpboot unless you have a different setup. For Example: cp pmagic_pxe_2012_2_27_x86_64.zip /tmp cd /tmp unzip pmagic_pxe_2012_2_27_x86_64.zip cd pmagic_pxe_2012_2_27_x86_64 # ls -l total 12 drwxr-xr-x  3 root root 4096 Feb 27 15:48 boot drwxr-xr-x  2 root root 4096 Mar 17 22:19 pmagic cp -r pmagic /tftpboot As I mentioned earlier, we dont change anything to the default pmagic distro. Simply provide the add-on package via PXE append options. If you are using a menu based PXE server, then add an entry to your menu. For example /tftpboot/pxelinux.cfg/default can be appended with following section. LABEL Diskless Boot With InfiniBand Support MENU LABEL Diskless Boot With InfiniBand Support KERNEL pmagic/bzImage APPEND initrd=pmagic/initrd.img,pmagic/ib-pxe-addon.cgz edd=off load_ramdisk=1 prompt_ramdisk=0 rw vga=normal loglevel=9 max_loop=256 TEXT HELP * A Linux Image which can be used to PXE Boot w/ IB tools ENDTEXT Note: Keep the line starting with "APPEND" as a single line. If you use host specific files in pxelinux.cfg, then you can use that specific file to add the above mentioned entry. Boot Computer over PXE Now boot your desired compute machine over PXE. This does not have to be over InfiniBand. Just use your standard ethernet interface and network. If using menus, then pick the new entry that you created in previous section. Enable IPoIB After a few minutes, you will be booted into Parted Magic environment. Open a terminal session and see if InfiniBand is enabled. You can use commands like: ifconfig -a ibstat ibv_devices ibv_devinfo If you are connected to InfiniBand network with an active Subnet Manager, then your IB interfaces must have come online by now. You can proceed and assign IP address to them. This will enable you at IPoIB layer. Example InfiniBand Diagnostic Tools I have added several InfiniBand Diagnistic tools in this add-on. You can use from following list: ibstat, ibstatus, ibv_devinfo, ibv_devices perfquery, smpquery ibnetdiscover, iblinkinfo.pl ibhosts, ibswitches, ibnodes Wrap Up This concludes this weblog. Here we saw how to bring up a computer with IPoIB and InfiniBand diagnostic tools without installing anything on it. Its almost like running diskless !

    Read the article

  • Microsoft Cloud Day - the ups and downs

    - by Charles Young
    The term ‘cloud’ can sometimes obscure the obvious.  Today’s Microsoft Cloud Day conference in London provided a good example.  Scott Guthrie was halfway through what was an excellent keynote when he lost network connectivity.  This proved very disruptive to his presentation which centred on a series of demonstrations of the Azure platform in action.  Great efforts were made to find a solution, but no quick fix presented itself.  The venue’s IT facilities were dreadful – no WiFi, poor 3G reception (forget 4G…this is the UK) and, unbelievably, no-one on hand from the venue staff to help with infrastructure issues.  Eventually, after an unscheduled break, a solution was found and Scott managed to complete his demonstrations.  Further connectivity issues occurred during the day. I can say that the cause was prosaic.  A member of the venue staff had interfered with a patch board and inadvertently disconnected Scott Guthrie’s machine from the network by pulling out a cable. I need to state the obvious here.  If your PC is disconnected from the network it can’t communicate with other systems.  This could include a machine under someone’s desk, a mail server located down the hall, a server in the local data centre, an Internet search engine or even, heaven forbid, a role running on Azure. Inadvertently disconnecting a PC from the network does not imply a fundamental problem with the cloud or any specific cloud platform.  Some of the tweeted comments I’ve seen today are analogous to suggesting that, if you accidently unplug your microwave from the mains, this suggests some fundamental flaw with the electricity supply to your house.   This is poor reasoning, to say the least. As far as the conference was concerned, the connectivity issue in the keynote, coupled with some later problems in a couple of presentations, served to exaggerate the perception of poor organisation.   Software problems encountered before the conference prevented the correct set-up of a smartphone app intended to convey agenda information to attendees.  Although some information was available via this app, the organisers decided to print out an agenda at the last moment.  Unfortunately, the agenda sheet did not convey enough information, and attendees were forced to approach conference staff through the day to clarify locations of the various presentations. Despite these problems, the overwhelming feedback from conference attendees was very positive.  There was a real sense of excitement in the morning keynote.  For many, this was their first sight of new Azure features delivered in the ‘spring’ release.  The most common reaction I heard was amazement and appreciation that Azure’s new IaaS features deliver built-in template support for several flavours of Linux from day one.  This coupled with open source SDKs and several presentations on Azure’s support for Java, node.js, PHP, MongoDB and Hadoop served to communicate that the Azure platform is maturing quickly.  The new virtual network capabilities also surprised many attendees, and the much improved portal experience went down very well. So, despite some very irritating and disruptive problems, the event served its purpose well, communicating the breadth and depth of the newly upgraded Azure platform.  I enjoyed the day very much.

    Read the article

  • Moving from windows to linux

    - by rincewind
    I need to reconcile these 2 facts: I don't feel comfortable working on Linux; I need to develop software for Linux. Some background: I have a 10+ years of programming experience on Windows (almost exclusively C/C++, but some .NET as well), I was a user of FreeBSD at home for about 3 years or so (then had to go back to Windows), and I've never had much luck with Linux. And now I have to develop software for Linux. I need a plan. On Windows, you can get away with just knowing a programming language, an API you're coding against, your IDE (VisualStudio) and some very basic tools for troubleshooting (Depends, ProcessExplorer, DebugView, WinDbg). Everything else comes naturally. On Linux, it's a very different story. How the hell would I know what DLL (sorry, Shared Object) would load, if I link to it from Firefox plugin? What's the Linux equivalent of inserting __asm int 3/DebugBreak() in the source and running the program, and then letting the OS call a debugger? Why the hell release builds use something, called appLoader, while debug builds work somehow different? Worst of all: how to provision Linux development environment? So, taking into account that hatred is usually associated with not knowing enough, what would you recommend? I'm ok with Emacs and GCC. I need to educate myself as a Linux admin/user, and I need to learn proper troubleshooting tools (strace is cool, btw), equivalents to the ones I mentioned above. Do I need to do Linux From Scratch? Or do I need to just read some books (I've read "UNIX programming enviornment" by Kernighan and "Advanced Programming..." by Stevens, but I need to learn something more practical)? Or do I need to have some Linux distro on my home computer?

    Read the article

  • wifi hardware switch doesn't work on a Dell 1018

    - by user42566
    I have a problem with my Dell 1018 Inspiron. I can't switch the wifi on, through the key on the keyboard. I think it's a driver problem since Ubuntu 11.10. This are the versions i tried: Ubuntu 10.04 / 10.10 It's possible to install the driver by hand: sudo add-apt-repository ppa:lexical/hwe-wireless sudo apt-get update sudo apt-get install rtl8192ce-dkms Ubuntu 11.04 It works out of the box Ubuntu 11.10 / 12.04 I haven’t found any solution for these versions. The "ppa:lexical/hwe-wireless" doesn't work for these versions. It says Can not find package rtl8192ce-dkms. The window of additional drivers is empty. So I can't install the driver. The wired network works good. Here is some information: 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: yes sudo lshw -class network *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 05 serial: 5c:26:0a:0d:20:10 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8105e-1.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0f2c000-f0f2cfff memory:f0f18000-f0f1bfff *-network description: Wireless interface product: RTL8188CE 802.11b/g/n WiFi Adapter vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:07:00.0 logical name: wlan0 version: 01 serial: 70:f1:a1:fe:15:bd width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl8192ce driverversion=3.2.0-22-generic-pae firmware=N/A ip=192.168.1.76 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 ioport:3000(size=256) memory:f0100000-f0103fff mark@mark-Inspiron-1018:~$ mark@mark-Inspiron-1018:~$ sudo lspci -nn 00:00.0 Host bridge [0600]: Intel Corporation N10 Family DMI Bridge [8086:a010] 00:02.0 VGA compatible controller [0300]: Intel Corporation N10 Family Integrated Graphics Controller [8086:a011] 00:02.1 Display controller [0380]: Intel Corporation N10 Family Integrated Graphics Controller [8086:a012] 00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 02) 00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 1 [8086:27d0] (rev 02) 00:1c.1 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 2 [8086:27d2] (rev 02) 00:1d.0 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) 00:1d.1 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) 00:1d.2 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) 00:1d.3 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 [8086:27cb] (rev 02) 00:1d.7 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 02) 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) 00:1f.0 ISA bridge [0601]: Intel Corporation NM10 Family LPC Controller [8086:27bc] (rev 02) 00:1f.2 SATA controller [0106]: Intel Corporation N10/ICH7 Family SATA Controller [AHCI mode] [8086:27c1] (rev 02) 00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family SMBus Controller [8086:27da] (rev 02) 05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) 07:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) mark@mark-Inspiron-1018:~$ mark@mark-Inspiron-1018:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 174f:1127 Syntek mark@mark-Inspiron-1018:~$

    Read the article

  • Sound stopped working

    - by Brian West
    I ran through the troubleshooting at https://help.ubuntu.com/community/SoundTroubleshooting It did not play the test sound, and it also does not play sounds during speaker-test. It does play sounds when I adjust my volume on my computer (using pommed). It worked just the other day, but this is the first time I've tested it since last night, when I put it to pm-suspend-hybrid and it half-woke up (the backlight came on, but it didn't fully wake up), then went back, then half-woke again, but was frozen like that. I had to do a manual reboot of the machine when that happened. Now my sound doesn't work, except for adjusting the volume (where the little "beep" sound plays). During the troubleshooting, it recognized my sound card, the sound modules, and the sound card's installation. I've tried removing ~/.pulse, but to no avail. Also, if it's any help, pulseaudio is running, but pulseaudio --check returns nothing, which the manpage suggests indicates an error. Edit: I should probably clarify that the wake up from the suspend-hybrid was not provoked in any way. I was laying in bed when I noticed my room was brighter suddenly, so I got up to check on it.

    Read the article

  • How to hire support people?

    - by Martin
    I manage a tech support team at a mid-sized software company. We are the last line of support, so issues that we can't fix need to be escalated to the development team. When I joined the company, our team wasn't capable of much beyond using a specific set of troubleshooting steps to solve known issues and escalating anything else to the developers. It's always been a goal of mine for our team to shoulder as much of the support burden as possible without ever bothering a developer. Over the past few years, I, along with several new hires I've made, have made pretty good progress in that direction. We've coded our own troubleshooting tools which now ship with several of our products. When users have never-before-seen issues, we analyze stack traces and troubleshoot down to the code level, and if we need to submit a bug, half the time we've already identified in the code where in the code the bug is and offered a patch to fix it. Here's the problem I've always had: finding support people capable of the work I've described above is really difficult. I've hired 3 people in the past 3 years, and I've probably looked at several thousand resumes and conducted several hundred phone screens to do so. I know it's pretty well accepted that hiring good people is tough in the tech industry, but it seems that support is especially difficult -- there are clearly thousands of people walking around calling themselves support analysts, but 99%+ of them seemingly aren't capable of anything beyond reading a script. I'm curious if anyone has experience recruiting the sort of folks I'm talking about, and if you have any suggestions to share. We've tried all sorts of things -- different job titles/descriptions, using headhunters, etc. And while we've managed to hire a few good folks, it's basically taken us a year to find an appropriate candidate for each opening we've had, and I can't help but wonder if there's something we could be doing differently.

    Read the article

  • At the Java DEMOgrounds - Oracle Java ME Embedded Enables the “Internet of Things”

    - by Janice J. Heiss
    I caught up with Oracle’s Robert Barnes, Senior Director, Java Product Management, who was demonstrating a new product from Oracle’s Java Platform, Micro Edition (Java ME) product portfolio, Oracle Java ME Embedded 3.2, a complete client Java runtime optimized for microcontrollers and other resource-constrained devices. Oracle’s Java ME Embedded 3.2 is a Java ME runtime based on CLDC 1.1 (JSR-139) and IMP-NG (JSR-228).“What we are showing here is the Java ME Embedded 3.2 that we announced last week,” explained Barnes. “It’s the start of the 'Internet of Things,’ in which you have very very small devices that are on the edge of the network where the sensors sit. You often have a middle area called a gateway or a concentrator which is fairly middle to higher performance. On the back end you have a very high performance server. What this is showing is Java spanning all the way from the server side right down towards the type of chip that you will get at the sensor side as the network.” Barnes explained that he had two different demos running.The first, called the Solar Panel System Demo, measures the brightness of the light.  “This,” said Barnes, “is a light source demo with a Cortex M3 controlling the motor, on the end of which is a sensor which is measuring the brightness of the lamp. This is recording the data of the brightness of the lamp and as we move the lamp out of the way, we should be able using the server to turn the sensor towards the lamp so the brightness reading will go higher. This sends the message back to the server and we can look at the web server sitting on the PC underneath the desk. We can actually see the data being passed back effectively through a back office type of function within a utility environment.” The second demo, the Smart Grid Response Demo, Barnes explained, “has the same board and processor and is still using Java ME embedded with a different app on top. This is a demand response demo. What we are seeing within the managing environment is that people want to track the pricing signals of the electricity. If it’s particularly expensive at any point in time, they may turn something off. This demo sets the price of the electricity as though this is coming from the back of the server sending pricing signals to my home.” The demo had a lamp and a fan and it was tracking the price of electricity. “If I set the price of the electricity to go over 5 cents, then the device will turn off,” explained Barnes. “I can go into my settings and, in this case, change the price to 50 cents and we can wait a minus and the lamp will go off. When I change the pricing signal so that it is lower, the lamp will come back on. The key point is that the Java software we have running is the same across all the different devices; it’s a way to build applications across multiple devices using the same software. This is important because it fixes peak loading on the network and can stops blackouts.” This demo brought me back to a prior decade when Sun Microsystems first promoted  Jini technology, a version of Java that would put everything on the network and give us the smart home. Your home would be automated to tell you when you were out of milk, when to change your light bulbs, etc. You would have access to the web and the network throughout your home.It’s interesting to see how technology moves over time – from the smart home to the Internet of Things.

    Read the article

  • Dell 3721 Wifi problem Ubuntu 13.04

    - by Sebastian
    I have a Dell 3721 which comes original with windows 8. I managed it to install ubuntu 12.10 on this laptop, even there was no out of the box drivers. With 12.10 I was forces to install this .deb package couple of times. After installing it, it was ok for some weeks before I have to install it again. Maybe some security updates destroy something which made in necessary to install it again... http://jas.gemnetworks.com/debian/pool/main/w/wireless-bcm43142/wireless-bcm43142-dkms_6.20.55.19-1_amd64.deb My problem is, that this package isnt working with ubuntu 13.04 anymore. So I cant use Wifi now. Also my display is almost dark, I cant change the brightness level with ubuntu 13.04. Hope you can give me some advice. Dell:~$ sudo lspci -nn 00:00.0 Host bridge [0600]: Intel Corporation 3rd Gen Core processor DRAM Controller [8086:0154] (rev 09) 00:02.0 VGA compatible controller [0300]: Intel Corporation 3rd Gen Core processor Graphics Controller [8086:0166] (rev 09) 00:14.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller [8086:1e31] (rev 04) 00:16.0 Communication controller [0780]: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 [8086:1e3a] (rev 04) 00:1a.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) 00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller [8086:1e20] (rev 04) 00:1c.0 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 [8086:1e10] (rev c4) 00:1c.1 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 [8086:1e12] (rev c4) 00:1d.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 [8086:1e26] (rev 04) 00:1f.0 ISA bridge [0601]: Intel Corporation HM76 Express Chipset LPC Controller [8086:1e59] (rev 04) 00:1f.2 SATA controller [0106]: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] [8086:1e03] (rev 04) 00:1f.3 SMBus [0c05]: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller [8086:1e22] (rev 04) 01:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) 02:00.0 Network controller [0280]: Broadcom Corporation BCM43142 802.11b/g/n [14e4:4365] (rev 01) @Dell:~$ lsusb Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 0a5c:21d7 Broadcom Corp. Bus 001 Device 004: ID 0bda:0129 Realtek Semiconductor Corp. Bus 001 Device 005: ID 0c45:64ad Microdia @Dell:~$ lspci -nn | grep VGA 00:02.0 VGA compatible controller [0300]: Intel Corporation 3rd Gen Core processor Graphics Controller [8086:0166] (rev 09) @Dell:~$ sudo lshw -class network *-network Beschreibung: Ethernet interface Produkt: RTL8101E/RTL8102E PCI Express Fast Ethernet controller Hersteller: Realtek Semiconductor Co., Ltd. Physische ID: 0 Bus-Informationen: pci@0000:01:00.0 Logischer Name: eth0 Version: 05 Seriennummer: xx:xx:xx:xx:xx:xx Größe: 100Mbit/s Kapazität: 100Mbit/s Breite: 64 bits Takt: 33MHz Fähigkeiten: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation Konfiguration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw ip=192.168.2.103 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s Ressourcen: irq:42 ioport:2000(Größe=256) memory:c0404000-c0404fff memory:c0400000-c0403fff *-network UNGEFORDERT Beschreibung: Network controller Produkt: BCM43142 802.11b/g/n Hersteller: Broadcom Corporation Physische ID: 0 Bus-Informationen: pci@0000:02:00.0 Version: 01 Breite: 64 bits Takt: 33MHz Fähigkeiten: pm msi pciexpress bus_master cap_list Konfiguration: latency=0 Ressourcen: memory:c0500000-c0507fff

    Read the article

  • Wireless doesn't work on a Broadcom BCM4312

    - by Boderick
    As stated, I've just upgraded to 12.04 and my Dell Inspiron 1545 isn't recognising its wireless card and I was wondering if anybody could help? Edit: Okay, so I found the wireless card by using lspci -vvv and it returned this: 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) Subsystem: Dell Wireless 1397 WLAN Mini-Card Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast TAbort- SERR- Kernel modules: ssb lsmod Module Size Used by dm_crypt 22528 0 joydev 17393 0 dell_wmi 12601 0 sparse_keymap 13658 1 dell_wmi dell_laptop 13671 0 dcdbas 14098 1 dell_laptop psmouse 72919 0 uvcvideo 67203 0 serio_raw 13027 0 videodev 86588 1 uvcvideo snd_hda_codec_idt 60251 1 mac_hid 13077 0 snd_hda_intel 32765 5 snd_hda_codec 109562 2 snd_hda_codec_idt,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec parport_pc 32114 0 rfcomm 38139 0 bnep 17830 2 ppdev 12849 0 snd_pcm 80845 3 snd_hda_intel,snd_hda_codec bluetooth 158438 10 rfcomm,bnep snd_seq_midi 13132 0 snd_rawmidi 25424 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq binfmt_misc 17292 1 snd 62064 18 snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm lp 17455 0 parport 40930 3 parport_pc,ppdev,lp sky2 53628 0 ums_realtek 17920 0 uas 17699 0 i915 414603 3 wmi 18744 1 dell_wmi drm_kms_helper 45466 1 i915 drm 197692 4 i915,drm_kms_helper i2c_algo_bit 13199 1 i915 video 19068 1 i915 usb_storage 39646 1 ums_realtek ifconfig -a eth0 Link encap:Ethernet HWaddr 00:23:ae:24:71:45 inet addr:192.168.1.158 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::223:aeff:fe24:7145/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14340 errors:0 dropped:0 overruns:0 frame:0 TX packets:10191 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:15403754 (15.4 MB) TX bytes:1262570 (1.2 MB) Interrupt:18 ham0 Link encap:Ethernet HWaddr 7a:79:05:2d:b0:f7 inet addr:5.45.176.247 Bcast:5.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::7879:5ff:fe2d:b0f7/64 Scope:Link inet6 addr: 2620:9b::52d:b0f7/96 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1404 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:179 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:0 (0.0 B) TX bytes:27480 (27.4 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:433 errors:0 dropped:0 overruns:0 frame:0 TX packets:433 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:60051 (60.0 KB) TX bytes:60051 (60.0 KB) iwconfig lo no wireless extensions. ham0 no wireless extensions. eth0 no wireless extensions. the results for sudo lshw -class network *-network description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:0c:00.0 logical name: eth1 version: 01 serial: 00:22:5f:77:1f:e6 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:17 memory:f69fc000-f69fffff *-network description: Ethernet interface product: 88E8040 PCI-E Fast Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 13 serial: 00:23:ae:24:71:45 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.30 duplex=full firmware=N/A ip=192.168.1.158 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:45 memory:f68fc000-f68fffff ioport:de00(size=256) *-network description: Ethernet interface physical id: 2 logical name: ham0 serial: 7a:79:05:2d:b0:f7 size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full firmware=N/A ip=5.45.176.247 link=yes multicast=yes port=twisted pair speed=10Mbit/s and the results of rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: yes Hard blocked: yes 1: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: yes

    Read the article

  • Unable to Sign in to the Microsoft Online Services Signin application from Windows 7 client located behind ISA firewall

    - by Ravindra Pamidi
    A while ago i helped a customer troubleshoot authentication problem with Microsoft Online Services Signin application.  This customer was evaluating Microsoft BPOS (Business Productivity Online Services) and was having trouble using the single sign on application behind ISA 2004 firewall.The network structure is fairly simple with single Windows 2003 Active Directory domain and Windows 7 clients. On a successful logon to the Microsoft Online Services Signin application, this application provides single signon functionality to all of Microsoft online services in the BPOS package. Symptoms:When trying to signin it fails with error "The service is currently unavailable. Please try again later. If problems continue, contact your service administrator". If ISA 2004 firewall is removed from the picture the authentication succeeds.Troubleshooting: Enabled ISA Server firewall logging along with Microsoft Network Monitor tool on the Windows 7 Client while reproducing the issue. Analysis of the ISA Server Firewall logs and Microsoft Network capture revealed that the Microsoft Online Services Sign In application when sending request to ISA Server does not send the domain credentials and as a result ISA Server responds with an error code of HTTP 407 Proxy authentication required listing out the supported authentication mechanisms.  The application in question is expected to send the credentials of the domain user in response to this request. However in this case, it fails to send the logged on user's domain credentials. Bit of researching on the Internet revealed that The "Microsoft Online Services Sign In" application by default does not support Outbound Internet Proxy authentication. In order for it to send the logged on user's domain credentials we had to make  changes to its configuration file "SignIn.exe.config" located under "Program Files\Microsoft Online Services\Sign In" folder. Step by Step details to configure the configuration file are documented on Microsoft TechNet website given below.  Configure your outbound authenticating proxy serverhttp://www.microsoft.com/online/help/en-us/helphowto/cc54100d-d149-45a9-8e96-f248ecb1b596.htm After the above problem was addressed we were still not able to use the "Microsoft Online Services Sign In" application and it failed with the same error.  Analysis of another network capture revealed that the application in question is now sending the required credentials and the connection seems to terminate at a later stage. Enabled verbose logging for the "Microsoft Online Services Sign In" application and then reproduced the problem. Analysis of the logs revealed a time difference between the local client and Microsoft Online services server of around seven minutes which is above the acceptable time skew of five minutes. Excerpt from Microsoft Online Services Sign In application verbose log:  1/26/2012 1:57:51 PM Verbose SingleSignOn.GetSSOGenericInterface SSO Interface URL: https://signinservice.apac.microsoftonline.com/ssoservice/UID1/26/2012 1:57:52 PM Exception SSOSignIn.SignIn The security timestamp is invalid because its creation time ('2012-01-26T08:34:52.767Z') is in the future. Current time is '2012-01-26T08:27:52.987Z' and allowed clock skew is '00:05:00'.1/26/2012 1:57:52 PM Exception SSOSignIn.SignIn  Although the Windows 7 Clients successfully synchronized time to the domain controller for the domain, the domain controller was not configured to synchronize time with external NTP servers. This caused a gradual drift in time on the network thus resulting in the above issue. Reconfigured the domain controller holding the PDC FSMO role to synchronize time with external time source ( time.nist.gov ) and edited the system policy on the ISA server firewall to allow NTP traffic to time.nist.gov Configure the time source for the forest:Windows Time Servicehttp://technet.microsoft.com/en-us/library/cc794937(WS.10).aspx Forced synchronization of Windows time using the command w32tm /resync on the domain controller and later on the clients each of which had corrected the seven minutes difference. This resolved the problem with logon to Microsoft Online Services Sign In.

    Read the article

  • SOA Suite 11g Purging Guide

    - by ShawnBailey
    We now have a single source of truth concerning Purging in My Oracle Support. The material is contained within the SOA 11g Infrastructure Database: Installation, Maintenance and Administration Guide under the 'Purging' tab. All of the previous purge related content for 11g is now deprecated and many of the documents will redirect to this Guide while others simply contain a disclaimer. What does the Guide contain? Summary Overview of Purging. What it does and why it's important Specific information on each release of 11g Available patches for each release of 11g and recommendations How to run the different purge scripts Tips on improving performance How to begin troubleshooting problems with the process How to identify orphaned records Useful reference information Here are a couple of screen shots to help with navigation: Guide Landing Page: (click image for full view) Select the 'Purging' tab: (click image for full view) The left menu contains the following options: Alternative: Database Partitioning What to do on 11gR1 GA (11.1.1.1) What to do on PS1 (11.1.1.2) What to do on PS2 (11.1.1.3) What to do on PS3 (11.1.1.4) What to do on PS4 (11.1.1.5) Overview of PS5 (11.1.1.6) Purging Step by Step Performance Tips Troubleshooting Purge Orphaned Records Reference This resource goes hand in hand with the excellent documents SOA 11g Database Growth Management Strategy and Start Small, Grow Fast available on OTN. The latest product documentation can be found here.

    Read the article

  • AME : How to Diagnose Issues With the Default Approver List in Purchasing When Using Approvals Management

    - by Oracle_EBS
    Do you need help in understanding the concepts or how to setup the Approval Management Engine (AME) for requisition approvals? See the new diagnostic Note 1437183.1 'AME : How to Diagnose Issues With the Default Approver List in Purchasing When Using Approvals Management'. AME is designed to generate the approval list according to the conditions and rules you define in the setup. This troubleshooting guide will help you understand how AME builds the default approval list for Purchasing and help users find solutions for scenarios where the approval list fails to be generated. Follow along with the logical steps for troubleshooting.  The note first reviews how to generate the AME Setup report.   For example in the note we see a fragment of the setup report. Notice it has different sections for each one of the setup categories including attributes, conditions, rules, action types, approval groups etc.  How the default approval list is built in AME is then reviewed, followed by the logical steps for diagnosing issues.  The diagnostic steps include how to run the Test Workbench, as well as how to obtain valuable debug and exception information.  Then follow along using the steps to build a simple test case to sharpen your understanding.

    Read the article

  • Try the Oracle Database Appliance Manager Configurator - For Fun!

    - by pwstephe-Oracle
    Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 If you would like to get a first hand glimpse of how easy it is to configure an ODA, even if you don’t have access to one, it’s possible to download the Appliance Manager Configurator from the Oracle Technology Network, and run it standalone on your PC or Linux/Unix  workstation. The configurator is packaged in a zip file that contains the complete Java environment to run standalone. Once the package is downloaded and unzipped it’s simply a matter of launching it using the config command or shell depending on your runtime environment. Oracle Appliance Manager Configurator is a Java-based tool that enables you to input your deployment plan and validate your network settings before an actual deployment, or you can just preview and experiment with it. Simply download and run the configurator on a local client system which can be a Windows, Linux, or UNIX system. (For Windows launch the batch file config.bat for Linux/Unix environments, run  ./ config.sh). You will be presented with the very same dialogs and options used to configure a production ODA but on your workstation. At the end of a configurator session, you may save your deployment plan in a configuration file. If you were actually ready to deploy, you could copy this configuration file to a real ODA where the online Oracle Appliance Manager Configurator would use the contents to deploy your plan in production. You may also print the file’s content and use the printout as a checklist for setting up your production external network configuration. Be sure to use the actual production network addresses you intend to use it as this will only work correctly if your client system is connected to same network that will be used for the ODA. (This step is not necessary if you are just previewing the Configurator). This is a great way to get an introductory look at the simple and intuitive Database Appliance configuration interface and the steps to configure a system. /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;}

    Read the article

  • Should I expose IObservable<T> on my interfaces?

    - by Alex
    My colleague and I have dispute. We are writing a .NET application that processes massive amounts of data. It receives data elements, groups subsets of them into blocks according to some criterion and processes those blocks. Let's say we have data items of type Foo arriving some source (from the network, for example) one by one. We wish to gather subsets of related objects of type Foo, construct an object of type Bar from each such subset and process objects of type Bar. One of us suggested the following design. Its main theme is exposing IObservable objects directly from the interfaces of our components. // ********* Interfaces ********** interface IFooSource { // this is the event-stream of objects of type Foo IObservable<Foo> FooArrivals { get; } } interface IBarSource { // this is the event-stream of objects of type Bar IObservable<Bar> BarArrivals { get; } } / ********* Implementations ********* class FooSource : IFooSource { // Here we put logic that receives Foo objects from the network and publishes them to the FooArrivals event stream. } class FooSubsetsToBarConverter : IBarSource { IFooSource fooSource; IObservable<Bar> BarArrivals { get { // Do some fancy Rx operators on fooSource.FooArrivals, like Buffer, Window, Join and others and return IObservable<Bar> } } } // this class will subscribe to the bar source and do processing class BarsProcessor { BarsProcessor(IBarSource barSource); void Subscribe(); } // ******************* Main ************************ class Program { public static void Main(string[] args) { var fooSource = FooSourceFactory.Create(); var barsProcessor = BarsProcessorFactory.Create(fooSource) // this will create FooSubsetToBarConverter and BarsProcessor barsProcessor.Subscribe(); fooSource.Run(); // this enters a loop of listening for Foo objects from the network and notifying about their arrival. } } The other suggested another design that its main theme is using our own publisher/subscriber interfaces and using Rx inside the implementations only when needed. //********** interfaces ********* interface IPublisher<T> { void Subscribe(ISubscriber<T> subscriber); } interface ISubscriber<T> { Action<T> Callback { get; } } //********** implementations ********* class FooSource : IPublisher<Foo> { public void Subscribe(ISubscriber<Foo> subscriber) { /* ... */ } // here we put logic that receives Foo objects from some source (the network?) publishes them to the registered subscribers } class FooSubsetsToBarConverter : ISubscriber<Foo>, IPublisher<Bar> { void Callback(Foo foo) { // here we put logic that aggregates Foo objects and publishes Bars when we have received a subset of Foos that match our criteria // maybe we use Rx here internally. } public void Subscribe(ISubscriber<Bar> subscriber) { /* ... */ } } class BarsProcessor : ISubscriber<Bar> { void Callback(Bar bar) { // here we put code that processes Bar objects } } //********** program ********* class Program { public static void Main(string[] args) { var fooSource = fooSourceFactory.Create(); var barsProcessor = barsProcessorFactory.Create(fooSource) // this will create BarsProcessor and perform all the necessary subscriptions fooSource.Run(); // this enters a loop of listening for Foo objects from the network and notifying about their arrival. } } Which one do you think is better? Exposing IObservable and making our components create new event streams from Rx operators, or defining our own publisher/subscriber interfaces and using Rx internally if needed? Here are some things to consider about the designs: In the first design the consumer of our interfaces has the whole power of Rx at his/her fingertips and can perform any Rx operators. One of us claims this is an advantage and the other claims that this is a drawback. The second design allows us to use any publisher/subscriber architecture under the hood. The first design ties us to Rx. If we wish to use the power of Rx, it requires more work in the second design because we need to translate the custom publisher/subscriber implementation to Rx and back. It requires writing glue code for every class that wishes to do some event processing.

    Read the article

< Previous Page | 240 241 242 243 244 245 246 247 248 249 250 251  | Next Page >