Search Results

Search found 16948 results on 678 pages for 'static analysis'.

Page 248/678 | < Previous Page | 244 245 246 247 248 249 250 251 252 253 254 255  | Next Page >

• Can I set up a 2nd home wireless router, with router2 connecting to the internet through a desktop which is wirelessly connected to router1?

  - by gil b.

  Hi, I apologize for the crudeness of my MSPaint drawing, but please view my diagram of what I'd like to accomplish: Proposed home network architecture Currently, all devices are connected to 1 wireless router. I would like to make my own subnet, with a box in-between my subnet and the shared wireless router, so that I can learn about IDS, traffic analysis, etc. I was also given a cisco PIX firewall to play around with, and it'd be an added bonus if I could incorporate that into my network. The reason for this proposed architecture is so that I can monitor all MY traffic, without seeing anything going on with my roommates' traffic. my MAIN Question is, is it possible to have my desktop connect to the wireless router with internet via wireless card AND share that connection via the ethernet card, hooked to wireless router 2? cable modem - wireless router - desktop pc connected wirelessly - wireless router 2 getting internet from wired connection to desktop pc - laptops connected wirelessly The PIX can be left out for now, but I'm wondering if it could eventually be incorporated? THANKS!

  Read the article

• SQL Server cluster performance baseline

  - by Dwight T

  Currently I'm tasked with getting a good performance baseline on a SQL 2005 cluster. The main db on the server is for Sharepoint, but I would like to add other dbs on the cluster. I do have access to Quest's Performance Analysis tool to help. What are key factors to look at to see if the cluster can handle additional dbs? Do you look at different performance indicators for a cluster vs a stand alone sql server? One db will be a low usage transactional db and a read only db that is used for sales data. Thanks Dwight

  Read the article

• Nginx > Varnish > Gunicorn Error Too many Redirections

  - by kollo

  I have the following config: Nginx Varnish Gunicorn Django I want to cache 2 versions of same site (mobile & web) with Varnish. Gunicorn : WEB: gunicorn_django --bind 127.0.0.1:8181 MOBILE: gunicorn_django --bind 127.0.0.1:8182 Nginx: WEB: server { listen 80; server_name www.mysite.com; location / { proxy_pass http://127.0.0.1:8282; # pass to Varnish proxy_set_header X-Real-IP $remote_addr; proxy_set_header Host $host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; } } MOBILE: server { listen 80; server_name m.mysite.com; location / { proxy_pass http://127.0.0.1:8282; # pass to Varnish proxy_set_header X-Real-IP $remote_addr; proxy_set_header Host $host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; } } Varnish: default.vcl backend mobile_mysite { .host = "127.0.0.1"; .port = "8182"; } backend mysite { .host = "127.0.0.1"; .port = "8181"; } sub vcl_recv { if (req.http.host ~ "(?i)^(m.)?mysite.com$") { set req.http.host = "m.mysite.com"; set req.backend = mobile_mysite; }elsif (req.http.host ~ "(?i)^(www.)?mysite.com$") { set req.http.host = "mysite.com"; set req.backend = mysite; } if (req.url ~ ".*/static") { /* do not cache static content */ return (pass); } } The problem: On Nginx if I setup Mobile version with Varnish (port 8282) and let WEB version with Gunicorn( port 8181), MOBILE is cached by varnish, both WEB & MOBILE works but WEB is not cached. If I set the proxy_pass of WEB version to Varnish (port 8282) and restart Nginx I got an error when accessing web version (www.mysite.com) "Too many redirections" . I Think my problem come from the Varnish config file, as the site works well if I setup Nginx proxy_pass to Gunicorn ports (MOBILE & WEB).

  Read the article

• My home box as my own host?

  - by Majid

  Hi all, I have a 512 kb/s DSL service at home. I do not have a static IP but I can get one if I pay some extra to my ISP. Now, if I get the static IP, can I make my home box act as my internet host? What else do I need? Thanks P.S. I know that if at all possible, the site I make available this way might be slow, that is alright, my question is if it is possible at all. Edit: I need this for very small traffic. I am a php developer and for my projects I am often asked to provide a demo. I currently use a free hosting for this purpose but it is down most of the time and support is non-existent. So I thought to set-up my home computer as my test server. With this please note that: I will only occasionally have 'visitors' and that will be one or possibly two visitors at any time. These demos, are to showcase functionality, so no big images are served and page views will normally generate under 100KB of traffic.

  Read the article

• What's the piece of hardware listening on Facebook's or Wikipedia's IP address?

  - by Igor Ostrovsky

  I am trying to understand how massive sites like Facebook or Wikipedia work, for my intellectual curiosity. I read about various techniques for building scalable sites, but I am still puzzled about one particular detail. The part that confuses me is that ultimately, the DNS will map the entire domain to a single IP address, or a handful of IP addresses in the case of round-robin DNS. For example, wikipedia.org has only one type-A DNS record. So, people from all over the world visiting Wikipedia have to send a request to the one IP address specified in DNS. What is the piece of hardware that listens on the IP address for a massive site, and how can it possibly handle all the load coming from the requests for users all over the world? Edit 1: Thanks for all the responses! Anycast seems like a feasible answer... Does anyone know of a way to check whether a particular IP address is anycast-routed, so that I could verify that this really is the trick used in practice by large sites? Edit 2: After more reading on the topic, it appears that anycast is not typically used for dynamic web content. Anycast is usually used for UDP (e.g., DNS lookups), or sometimes for static content. One interesting thing to note is that Facebook uses profile.ak.fbcdn.net to host static content like style sheets and javascript libraries. Each time I ping this name, I get a response from a different IP address. However, I can't tell whether this is anycast in action, or a completely different technique. Back to my original question: as far as I can tell, even a large site will have a single expensive piece of load-balancing hardware listening on its handful of public IP addresses.

  Read the article

• Running docker in VPC and accessing container from another VPC machine

  - by Bogdan Gaza

  I'm having issues while running docker in AWS VPC. Here is my setup: I've got two machines running in VPC: 10.0.100.150 10.0.100.151 both having an elastic IPs assigned to them, both running in the same internet enabled subnet. Let's say I'm running a web server that serves static files in a container on the 10.0.100.150 machine the container: IP: 172.17.0.2 port 8111 is forwarded on the 8111 port on the machine. I'm trying to access the static files from my local machine (or another non-VPC machine also tried an EC2 instance not running in the VPC) and it work flawlessly. If I try to access the files from the other machine (10.0.100.151) it hangs. I'm using wget to pull the files. Tried to debug it with tcpdump and ngrep and that I have seen is that the request reaches the container. If I ngrep on the host machine I see the requests going in but no response going back. If I ngrep on the container I see the requests going in and the response going back. I've tried multiple iptables setups (with postrouting enabled, with manually forwarding ports etc) but no success. Help in any way - even debugging directions would be much appreciated. Thanks!

  Read the article

• Translating debian network configuration to gentoo

  - by thpetrus

  I just got rid off Debian on my VPS (OpenVZ) and installed Gentoo on it, however it is a plain Gentoo image without further configuration, i.e. no working network. I'm not familiar with Debian and coulnd't figure out how to get the network set up, these are the debian network files /etc/network/interfaces: auto venet0 iface venet0 inet manual up ifconfig venet0 up up ifconfig venet0 127.0.0.2 up route add default dev venet0 down route del default dev venet0 down ifconfig venet0 down iface venet0 inet6 manual up ifconfig venet0 add ipv6addr/128 down ifconfig venet0 del ipv6addr/128 up route -A inet6 add default dev venet0 down route -A inet6 del default dev venet0 auto venet0:0 iface venet0:0 inet static address external_ip netmask 255.255.255.255 auto venet0:1 iface venet0:1 inet static address internal_ip netmask 255.255.255.255 Please note that external_ip, internal_ip and ipv6addr are placeholders. I copied the /etc/resolv.conf, know the gateway_ip and also have another ouput of ifconfig, if necessary. This is what I came up with, /etc/conf.d/net: config_venet0="127.0.0.2 netmask 255.255.255.255 brd 0.0.0.0" config_venet0:0="external_ip netmask 255.255.255.255 brd 0.0.0.0" route_venet0:0="default via gateway_ip" config_venet0:1="internal_ip netmask 255.255.255.255 brd 0.0.0.0" Broadcast IP is taken from ifconfig debian output - however it doesn't work. A symbolic link net.venet0:0 -> net.lo in /etc/init.d/ was created and I added net.venet0:0 to the boot runlevel.

  Read the article

• Can't access one directory via HTTPS + public FQDN

  - by Justin James

  Hello - I have the strangest IIS error that I've ever seen in my life. I have an application/directory on an IIS server, that throws an error 500 when accessing ANY of the content in it, including HTML documents, when accessed via HTTPS AND the machines FQDN. When I access it with "localhost" it works fine. When I added a bogus entry for the NIC's IP in the hosts file, it worked fine. When I access it with the machines name and HTTP it works fine. Here's a chart (the machine's name is "lofn.titaniumcrowbar.com"): http - lofn.titaniumcrowbar.com: works https - lofn.titaniumcrowbar.com: broken https - localhost: works https - temp.titaniumcrowbar.com (put into hosts file): works I set up tracing, and I got some useless information: "The I/O operation has been aborted because of either a thread exit or an application request. (0x800703e3)" This would make sense, except this happens when pulling up static content. While the directory may be an "application", the content is all static in it. Any/all suggestions, no matter how strange, are VERY appreciated. Thanks! J.Ja

  Read the article

• Can't seem to stop Postfix backscatter

  - by Ian

  I've just migrated to a Postfix system and can't seem to stop the backscatter messages to unknown addresses on the site. I have a file, validrcpt, that lists all the valid emails on the site - about eight of them. Yet when a message is sent to a non-existent address, instead of just dropping it, postfix is replying with a "Recipient address rejected: User unknown in virtual mailbox table" email. Do I have something set wrong? I've read http://www.postfix.org/BACKSCATTER_README.html but unless I'm caffeine deficient, I don't see what's happening and perhaps I'm just to used to my old qmail setup. Here's postconf -n: alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_dot_mydomain = no biff = no broken_sasl_auth_clients = yes config_directory = /etc/postfix content_filter = smtp-amavis:[127.0.0.1]:10024 home_mailbox = Maildir/ inet_interfaces = all inet_protocols = ipv4 local_recipient_maps = hash:/etc/postfix/validrcpt mailbox_command = /usr/lib/dovecot/deliver -c /etc/dovecot/dovecot.conf -m "${EXTENSION}" mailbox_size_limit = 0 mydestination = localhost myhostname = localhost mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 myorigin = /etc/mailname policy-spf_time_limit = 3600s readme_directory = no recipient_bcc_maps = hash:/etc/postfix/recipient_bcc recipient_delimiter = + relay_recipient_maps = hash:/etc/postfix/relay_recipients relayhost = smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtp_use_tls = yes smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_recipient_restrictions = permit_mynetworks,permit_sasl_authenticated,reject_unauth_destination,check_policy_service unix:private/policy-spf,reject_rbl_client zen.spamhaus.org,reject_rbl_client bl.spamcop.net,reject_rbl_client cbl.abuseat.org,check_policy_service inet:127.0.0.1:10023 smtpd_relay_restrictions = permit_mynetworks permit_sasl_authenticated defer_unauth_destination smtpd_sasl_auth_enable = yes smtpd_sasl_authenticated_header = yes smtpd_sasl_local_domain = $myhostname smtpd_sasl_path = private/dovecot-auth smtpd_sasl_security_options = noanonymous smtpd_sasl_type = dovecot smtpd_sender_restrictions = reject_unknown_sender_domain smtpd_tls_auth_only = yes smtpd_tls_cert_file = /etc/dovecot/dovecot.pem smtpd_tls_key_file = /etc/dovecot/private/dovecot.pem smtpd_tls_mandatory_ciphers = medium smtpd_tls_mandatory_protocols = SSLv3, TLSv1 smtpd_tls_received_header = yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes tls_random_source = dev:/dev/urandom virtual_gid_maps = static:5000 virtual_mailbox_base = /home/vmail virtual_mailbox_domains = digitalhit.com virtual_mailbox_maps = hash:/etc/postfix/vmaps virtual_minimum_uid = 1000 virtual_uid_maps = static:5000

  Read the article

• Nginx and Gunicorn hanging on GET requests

  - by whatWhat

  I'm using Nginx + Gunicorn which is serving my Django project. All GET requests hang for ~1 min. The content seems to be available immediately as I can see it in the Browser inspector but the browser itself looks like it's still waiting for more data. Heres my Ngnix config #allow for up to 3 connections per second. limit_req_zone $binary_remote_addr zone=one:10m rate=3r/s; server { listen 80; server_name example.com; root /var/www/example.com/example/; # serve directly - analogous for static/staticfiles location /media/ { # this changes depending on your python version root /home/example/; } location /static/ { # if asset versioning is used if ($query_string) { expires max; } root /var/www/example.com; } location / { #Allow for a burst of 50. limit_req zone=one burst=50 nodelay; proxy_pass_header Server; proxy_set_header Host $http_host; proxy_redirect off; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Scheme $scheme; proxy_connect_timeout 10; proxy_read_timeout 10; proxy_pass http://localhost:8001/; } # what to serve if upstream is not available or crashes error_page 500 502 503 504 /media/50x.html; } My Gunicorn Config: bind = "127.0.0.1:8001" workers = 3 worker_class = "gevent" Is there anything obvious that would be causing the requests to stay open for so long?

  Read the article

• How can I scrape specific data from a website

  - by Stoney

  I'm trying to scrape data from a website for research. The urls are nicely organized in an example.com/x format, with x as an ascending number and all of the pages are structured in the same way. I just need to grab certain headings and a few numbers which are always in the same locations. I'll then need to get this data into structured form for analysis in Excel. I have used wget before to download pages, but I can't figure out how to grab specific lines of text. Excel has a feature to grab data from the web (Data-From Web) but from what I can see it only allows me to download tables. Unfortunately, the data I need is not in tables.

  Read the article

• CloudFront for dynamic content CDN

  - by Elad Lachmi

  I would like to use CF as a CDN for my entire site, including static and dynamic content. I have been using CF for static content for a while and I am very happy with the results. I am now doing POC of putting the web server completely behind CF. For the dynamic content I created a new distribution and set the origin to be my web server. Right now I'm looking to test the solution, so I have the web server on the original domain and the CF distribution on the amazon domain. This works with the exception of HTTPS urls and POST requests. For HTTPS requests, I see the requests are forwarded to the original site domain for now, but how will CF handle them when I move the distribution to the www cname? What configuration changes should I make so that CF forwards HTTPS requests to the origin? For POST requests, I want the post to be made to the origin server. Can I set this up in CF? Finally, the site has membership. Can I configure CF to pull all content from the origin if the user is logged in? Sorry for the long question. I'm a little lost and documentation for dynamic CF is still kind of scarce. Thank you!

  Read the article

• Network email alerts

  - by stephenfalken

  I would like to buy or d/l an application that will alert our sysadmin in the event of network failure, like via email and/or phone call. I've looked around the net before posting this question, but I have one main concern: if our network goes down, how can a network monitoring application send email to alert us that it's down? Doesn't this have to be an external application that looks at our network from outside? Well anyway, I want to find something that will handle this for us - freeware if possible, sice we're not looking for heavy analysis - just simple alerts. Advice is appreciated.

  Read the article

• Unable to ping gateway via bridge nic

  - by Ara

  I'm trying to install KVM on Ubuntu 12.04 server. We have multiple nic on this server of which we primarily use eth0. The server network runs fine(i'm able to ping gateway, ping dns server and ping servers on internet) with eth0 /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.22.194 netmask 255.255.255.0 network 192.168.22.0 broadcast 192.168.22.255 gateway 192.168.22.1 dns-nameservers 10.71.130.58 10.71.130.60 dns-search test.local I installed bridge-utils and configured br0 as below /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet manual auto br0 iface br0 inet static address 192.168.22.194 netmask 255.255.255.0 network 192.168.22.0 broadcast 192.168.22.255 gateway 192.168.22.1 dns-nameservers 10.71.130.58 10.71.130.60 dns-search test.local bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off Post which i'm able to ping servers on the same ip range 192.168.22.2-254 except for 192.168.22.1 (which is the gateway) also i'm not able to ping any other servers. I'm not able to ping this machine from network. The output for route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.22.1 0.0.0.0 UG 100 0 0 br0 192.168.22.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 192.168.122.0 0.0.0.0 255.255.255.0 U 0 0 0 virbr0 I've been struggling with this issue for past 5 days, would be of help if anyone can point me in the right direction to fix this issue. Thanks in advance

  Read the article

• OpenVZ with bridged interfaces and VLAN

  - by Deimosfr

  Hi, I've got a problem with OpenVZ with bridged VLAN. Here is my configuration: +------+ +-------+ +-----------+ +---------+ br0 |VE101 | | | | OpenBSD |----->| Debian |------->| | | WAN |--->| Router | | OpenVZ | +------+ | | | Firewall |----->| br0 br1 | br1 +------+ +-------+ +-----------+ +---------+------->|VE102 | |br0 | | |VLAN br0.110 +------+ v +---------+ |VE103.110| +---------+ I can't make VLAN work on br0 (br0.110) and I would like to understand why. I don't have any switch so no problem with unmanageable switch. I've configured a VLAN interface on OpenBSD in /etc/hostname.vlan110: inet 192.168.110.254 255.255.255.0 NONE vlan 110 vlandev sis1 And it seems to be working fine. I've also adapted my PF configuration to work with VLAN but I don't see any incoming traffic. On my Debian Lenny, here is my interfaces configuration : # The loopback network interface auto lo iface lo inet loopback # br0 auto br0 iface br0 inet static address 192.168.100.1 netmask 255.255.255.0 gateway 192.168.100.254 network 192.168.100.0 broadcast 192.168.100.255 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off # VLAN 110 auto br0.110 iface br0.110 inet static address 192.168.110.1 netmask 255.255.255.0 network 192.168.110.0 gateway 192.168.110.254 broadcast 192.168.110.255 pre-up vconfig add br0 110 post-down vconfig rem br0.110 It looks OK, but when I start my VE, here is the message: ... Configure veth devices: veth103.0 Adding interface veth103.0 to bridge br0.110 on CT0 for VE103 can't add veth103.0 to bridge br0.110: Operation not supported VE start in progress... So I've got one error here. I've followed this documentation http://wiki.openvz.org/VLAN but it doesn't work. I've certainly missed something but I don't know why. Someone could help me please? Thanks

  Read the article

• Configuring network route between two routers on home network

  - by Paul

  I have a home network - the main router connected to the internet (and has wifi) is a Netopia box. Connected to it is a Linksys router. Everything currently works - I can connect via the wireless network and get to the internet. Machines connected to the Linksys can connect with each other and connect to the internet. Both routers are configured to serve addresses via DHCP (Netopia 192.168.1.1 - 192.168.1.99), Linksys (192.168.0.1 - 192.168.0.100). Here's how they are connected: Internet <-> Netopia w/wifi (192.168.1.254) <-> Linksys (192.168.0.1) I decided I really need to allow wireless connections to also communicate with machines behind the Linksys router. Currently the Linksys is configured to obtain an IP address via DHCP. I thought this would be straightforward. I configured the Linksys to have a static IP address: IP: 192.168.1.100 Mask: 255.255.255.0 GW: 192.168.1.254 Then I configured a static route on the Netopia: Network: 192.168.0.0 Mask: 255.255.255.0 GW: 192.168.1.100 So it should now look like this: Internet <-> Netopia w/wifi (192.168.1.254) <-> (192.168.1.100) Linksys (192.168.0.1) I reset both routers. I cannot ping the Netopia (192.168.1.254) from inside the Linksys network, and if I attempt to ping 192.168.0.1 from a wifi connection I get a "Destination host not available" error. Obviously I'm missing something, but I'm not sure where. Any ideas on what I'm missing?

  Read the article

• Apache caching with mod_headers mod_expires

  - by Aaron Moodie

  Hi, I'm working on homework for uni and was hoping someone could clarify something for me. I need to set up the following: Configure the response header "Cache-Control" to have a "max-age" value of 7 days since access for all image files Configure the response header "Cache-Control" to have a "max-age" value of 5 days since modification for all static HTML files. Configure the response header "Cache-Control" to have a value of "public" for all static HTML and image files. Configure the response header "Cache-Control" to have a value of "private" for all PHP files. My question is whether it is better to use a FilesMatch, or the mod_expires ExpiresByType to best achieve this? I've so far used the following: <FilesMatch "\.(gif|jpe?g|png)$"> ExpiresDefault "access plus 7 days" Header set Cache-Control "public" </FilesMatch> <FilesMatch "\.(html)$"> ExpiresDefault "modification plus 5 days" Header set Cache-Control "public" </FilesMatch> <FilesMatch "\.(php)$"> Header set Cache-Control "private" </FilesMatch> Thanks.

  Read the article

• Fill a table from a RAND based formula in Excel 2010

  - by Greg Reynolds

  I am trying to do a Monte Carlo simulation using Excel, but a lot of the tutorials I have found are either for older versions of the product, or are not quite what I am after. A simple example of the kind of think I am after is: Cell A1 contains the formula to simulate (for example int(6*rand())+1 to simulate rolling a dice). I have 10 rows of "Trials". What I want is to somehow point each row at a different calculation of the formula in A1. So I would end up with something like Trial Value 1 2 2 5 3 6 4 2 5 1 6 3 7 2 8 4 9 2 10 1 I have tried playing with some of the "What-if Analysis" tools, but I am a bit lost.

  Read the article

• Debian, 2 NICs load-balancing or agregating with one same gateway

  - by pouney

  Hi, I have one server, with double NICs connected to one switch with the same gateway. Behind the switch we have internet. |Debian| - eth0 - switch - internet - eth1 - same I don't understand how to load-balancing between eth0 and eth1. The inbound/outbound traffic always use eth1. This is the config: # The primary network interface allow-hotplug eth0 auto eth0 iface eth0 inet static address 192.168.248.82 netmask 255.255.255.240 network 192.168.248.80 broadcast 192.168.248.95 gateway 192.168.248.81 allow-hotplug eth1 auto eth1 iface eth1 inet static address 192.168.248.83 netmask 255.255.255.240 network 192.168.248.80 broadcast 192.168.248.95 gateway 192.168.248.81 Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.248.80 0.0.0.0 255.255.255.240 U 0 0 0 eth1 192.168.248.80 0.0.0.0 255.255.255.240 U 0 0 0 eth0 0.0.0.0 192.168.248.81 0.0.0.0 UG 0 0 0 eth1 0.0.0.0 192.168.248.81 0.0.0.0 UG 0 0 0 eth0 Ips aren't real, it's just for the example. Anybody have an idea on correct routing to use eth0 on 192.168.248.82 and eth1 on 192.168.248.83 ? I have many example for multiple gateway but here it's the same. Thanks all. Regards

  Read the article

• Route through site-to-site VPN not working

  - by Jonathan

  I'm trying to set up a site-to-site VPN using RRAS on two 2K8r2 servers since yesterday. The connection is working at this point, but I can't get it to send traffic from one site to the other one. Set up: the set up is the same on both sites: the server is connected to a router that's connected to a modem. The routers act like a DHCP-server and assign IP addresses from the range subnet.21-subnet-.100. Both servers use a static IP address, subnet.11, and are set up as DMZ. Configuration: the servers are configured using the wizard to set up a site-to-site connection. This works with a demand-dial interface and a PPTP VPN connection. As mentioned, the VPN connection work properly. Problem: I can't get the servers to send the traffic for the other site, to be sent through the VPN connection. I added a static route on both server (home, office 1) and I can see the result in the IP routing table (home, office 1). I did this because the route didn't show up automatically. My guess is that this last step isn't right, for example because the routing table states "non demand-dial", which seems not correct. Home: Subnet: 10.0.1.0/24 Router: 10.0.1.1 Server: 10.0.1.11 (DMZ) DHCP: 10.0.1.21-10.0.1.100 RRAS DHCP: 10.0.1.101-10.0.1.150 Office 1: Subnet: 10.0.2.0/24 Router: 10.0.2.1 Server: 10.0.2.11 (DMZ) DHCP: 10.0.2.21-10.0.2.100 RRAS DHCP: 10.0.2.101-10.0.2.150 I hope someone has an idea to get this route working!

  Read the article

• Barriers to IPv6 deployment: addressing

  - by sysadmin1138

  There are several things that are keeping IPv6 deployment from being a topic of active discussion here at my work. There are the usual technical issues, but one non-technical one appears to be a major stumbling block on the path to actually getting a deployment project going. Addresses, memorizing of. Specifically, IPv4 addresses are comprehensible, and IPv6 addresses just look like a big long string of hex. The human mind has real trouble memorizing lists of more than 7-8 items, and an IPv4 address (192.168.231.148) has four items in it which makes it easy for us to memorize. A fully populated IPv6 address has not only 8 sections, but each section has 4 hex digits in it. IPv6 addresses were not designed for memorization. To the technician who knows that the DNS server is at 192.168.42.42 (or more likely "42.42", since the company prefix is likely memorized), the idea of memorizing an IPv6 address fills them with dread. Which in turn makes them much less enthusiastic about participating in an IPv6 deployment project. Because of how our network works we're not fully dynamic in terms of v4 addressing. We have several to many subnets that are entirely statically assigned for a variety of reasons, chief among them being that the overhead of static DHCP assignments is perceived as being too great. Also, some devices still aren't smart enough to pull DNS addresses out of DHCP while also having a static assignment, and therefore require manually configured DNS settings. Therefore, some v6 address memorization will have to be done. We're not under any mandate to get v6 out the door, so we don't have pressure from the top. However, it is time to start prepping our infrastructure to handle IPv6 even if we don't convert wholesale. For those of you who have been in IPv6-land for a while, what short-cut methods do you use to discuss or keep track of subnets and specific/critical IP addresses? If I can help reduce some of the dread surrounding IPv6 we might get the project going.

  Read the article

• Can I set up a 2nd home wireless router, with router2 connecting to the internet through a desktop which is wirelessly connected to router1?

  - by gil b.

  Hi, I apologize for the crudeness of my MSPaint drawing, but please view my diagram of what I'd like to accomplish: Proposed home network architecture Currently, all devices are connected to 1 wireless router. I would like to make my own subnet, with a box in-between my subnet and the shared wireless router, so that I can learn about IDS, traffic analysis, etc. I was also given a cisco PIX firewall to play around with, and it'd be an added bonus if I could incorporate that into my network. The reason for this proposed architecture is so that I can monitor all MY traffic, without seeing anything going on with my roommates' traffic. my MAIN Question is, is it possible to have my desktop connect to the wireless router with internet via wireless card AND share that connection via the ethernet card, hooked to wireless router 2? cable modem - wireless router - desktop pc connected wirelessly - wireless router 2 getting internet from wired connection to desktop pc - laptops connected wirelessly The PIX can be left out for now, but I'm wondering if it could eventually be incorporated? THANKS!

  Read the article

• Django apache + mod_wsgi with virtualenv

  - by ArgsKwargs

  I have some questions running multiple Django sites on a VPS I have a server that uses openPanel to automatically create VirtualHosts within apache2. My ideal situation is that I would have multiple virtualenvs with different dependencies installed so the python dist-packages directory isn't contaminated for different Django sites. For example: /home/user/virtualenv1 /home/user/virtualenv2 My django applications reside at /var/www, so For example: /var/www/djangosite1 /var/www/djangosite2 Now I've read upon openPanel docs and figured out the best thing todo is create a django.conf file inside the mydomain.com.inc folder, which looks something like: /etc/apache2/openpanel.d/mydomain.com.inc/django.conf DocumentRoot /var/www/djangosite1/project WSGIScriptAlias / /var/www/djangosite1/project/wsgi.py WSGIDaemonProcess mydomain python-path=/home/user/virtualenv1/lib/python2.6/site-packages <Directory /var/www/djangosite1/project> Order allow,deny Allow from all </Directory> Alias /static /var/www/djangosite1/project/static-root Now my problem is that this setup seems unable to find the virtualenv site-packages thus not recognizing any dependencies available in the given virtualenv Also, commenting out this line doesn't seem to break or change a thing: WSGIDaemonProcess mydomain python-path=/home/user/virtualenv1/lib/python2.6/site-packages For example: > service apache2 start ImportError: No module named South When I install South outside the virtualenv everything works

  Read the article

• nginx - proxy_pass is working - Apache isn't doing what it should...

  - by matthewsteiner

  So, I've got this in my nginx.conf: location ~* ^.+.(jpg|jpeg|gif|png|ico|css|zip|tgz|gz|rar|bz2|doc|xls|exe|pdf|ppt|txt|tar|mid|midi|wav|bmp|rtf|js)$ { root /var/www/vhosts/example.com/public/; access_log off; expires 30d; } location / { proxy_pass http://127.0.0.1:8080/; proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; } So anything that is a "static file" that exists will just be done with nginx. Otherwise, it should pass it off to Apache. Right now, static files are working correctly. However, if something is passed to apache and it's example.com or subdomain.example.com, apache just spits out the "Apache 2 Test Page" that you get if there's nothing there. Apache worked fine before, so I'm guessing it has to do with the way nginx is "asking". I'm not sure though. Any ideas?

  Read the article

• Default IPv6 route on debian squeeze does not come up after boot

  - by Georg Bretschneider

  I have a problem with my default IPv6 route not coming up after boot on a Debian Squeeze system. This is my config (/etc/network/interfaces): # Loopback device: auto lo iface lo inet loopback iface lo inet6 loopback # device: br0 auto br0 iface br0 inet static bridge_ports eth0 bridge_fd 0 address 88.198.62.xx broadcast 88.198.62.63 netmask 255.255.255.224 gateway 88.198.62.33 up route add -net 88.198.62.32 netmask 255.255.255.224 gw 88.198.62.33 br0 iface br0 inet6 static address 2a01:4f8:131:10x::2 netmask 64 gateway 2a01:4f8:131:100::1 up route -A inet6 add 2a01:4f8:131:100::1/59 dev br0 My inet comes up alright, but I have to exec the route command manually after boot to make IPv6 work. Otherwise I can't even reach my gateway. This is the output of ip -6 route show after boot: 2a01:4f8:131:10x::/64 dev br0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 unreachable fe80::/64 dev lo proto kernel metric 256 error -101 mtu 16436 advmss 16376 hoplimit 4294967295 fe80::/64 dev br0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 I already tried it with: up ip -6 route add 2a01:4f8:131:100::1 dev br0 up ip -6 route add default via 2a01:4f8:131:100::1 dev br0 in /etc/network/interfaces, but with the same results. If I execute those commands manually on my shell, everything starts working nicely. And yes, I tried with post-up instead of up, too. Only other changes I made was to activate ip forwarding for IPv6, because I want to run some LXC containers on that system.

  Read the article

< Previous Page | 244 245 246 247 248 249 250 251 252 253 254 255  | Next Page >