Search Results

Search found 1123 results on 45 pages for 'rev samuel'.

Page 25/45 | < Previous Page | 21 22 23 24 25 26 27 28 29 30 31 32  | Next Page >

  • HP Storageworks 448 tape drive input/output error with Ubuntu

    - by Dan D
    I'm trying to set a backup to tape of a machine using flexbackup. However any attempt to write to the tape drive (via either flexbackup or just tar) results in "/dev/st0: Input/output error" The machine seems to recognise the drive (HP Storageworks Ultrium 448) and that there's a tape in it and "mt status" seems to work... "mt -f /dev/st0 rewind" or "erase" throw no errors... root@stor001:/# mt status SCSI 2 tape drive: File number=0, block number=0, partition=0. Tape block size 0 bytes. Density code 0x42 (LTO-2). Soft error count since last status=0 General status bits on (41010000): BOT ONLINE IM_REP_EN root@stor001:/# cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: HL-DT-ST Model: DVDRAM GSA-4084N Rev: KS02 Type: CD-ROM ANSI SCSI revision: 05 Host: scsi2 Channel: 00 Id: 03 Lun: 00 Vendor: HP Model: Ultrium 2-SCSI Rev: S65D Type: Sequential-Access ANSI SCSI revision: 03 "tell" does however root@stor001:/# mt -f /dev/st0 tell /dev/st0: Input/output error Based on a forum post I found, I tried: root@stor001:/# dd if=/dev/zero of=/dev/nst0 bs=1024 count=10 10+0 records in 10+0 records out 10240 bytes (10 kB) copied, 5.0815 s, 2.0 kB/s which gave the person on the forum an error but seems to work for me. If anyone has any suggestions, I'm all ears...

    Read the article

  • S5000XVN Intel Motherboard - Only sees 12 out of 16GB of RAM

    - by Richie086
    So I have an older Intel S5000XVN motherboard, here are the specs CPU Arch : 2 CPU - 2 Cores - 2 Threads CPU PSN : Intel Xeon CPU 5160 @ 3.00GHz CPU EXT : MMX, SSE (1, 2, 3, 3S), EM64T, VT-x CPUID : 6.F.6 / Extended : 6.F CPU Cache : L1 : 2 x 32 / 2 x 32 KB - L2 : 4096 KB Core : Woodcrest (65 nm) / Stepping : B2 Freq : 2985.21 MHz (331.69 * 9) MB Brand : Intel MB Model : S5000XVN NB : Intel 5000X rev 31 SB : Intel 6321ESB rev 09 RAM : 16384 MB FB-DDR2 RAM Speed : 331.7 MHz (1:1) @ N/A Slot 1 : 2048MB (5300) Slot 1 Manufacturer : Kingston Slot 2 : 2048MB (5300) Slot 2 Manufacturer : Qimonda Slot 3 : 2048MB (5300) Slot 3 Manufacturer : Kingston Slot 4 : 2048MB (5300) Slot 4 Manufacturer : Qimonda Slot 5 : 2048MB (5300) Slot 5 Manufacturer : Kingston Slot 6 : 2048MB (5300) Slot 6 Manufacturer : Qimonda As you can clearly see, CPU-Z says I have 16GB of PC2-5300 RAM installed. For some reason in both BIOS and in Windows the maximum usable RAM is 12GB instead of 16GB. I have a dedicated video card connnected, so it can't be stealing RAM to use for the GPU (the S5000XVN does not have any onboard video). I am running Windows Server 2008 R2 x64 as the primary OS - so there should not be a memory limitation imposed on me from the OS. Has anyone experienced this before? Any ideas on how I can actually use all 16GB of RAM? I plan on using this machine to use for a Hyper-V server and have x2 Quad Core Xeon CPUs on the way as I write this post.

    Read the article

  • How to get an ARM CPU clock speed in Linux?

    - by MiKy
    I have an ARM-based embedded machine based on S3C2416 board. According to the specifications I have available there should be a 533 MHz ARM9 (ARM926EJ-S according to /proc/cpuinfo), however the software running on it "feels" slow, compared to the same software on my Android phone with a 528MHz ARM CPU. /proc/cpuinfo tells me that BogoMIPS is 266.24. I know that I should not trust BogoMIPS regarding performance ("Bogo" = bogus), however I would like to get a measurement on the actual CPU speed. On x86, I could use the rdtsc instruction to get the time stamp counter, wait a second (sleep(1)), read the counter again to get an approximation on the CPU speed, and according to my experience, this value was close enough to the real CPU speed. How can I find the actual CPU speed of given ARM processor? Update I found this simple Pi calculator, which I compiled both for my Android phone and the ARM board. The results are as follows: S3C2416 # cat /proc/cpuinfo Processor : ARM926EJ-S rev 5 (v5l) BogoMIPS : 266.24 Features : swp half fastmult edsp java ... #./pi_arm 10000 Calculation of PI using FFT and AGM, ver. LG1.1.2-MP1.5.2a.memsave ... 8.50 sec. (real time) Android # cat /proc/cpuinfo Processor : ARMv6-compatible processor rev 2 (v6l) BogoMIPS : 527.56 Features : swp half thumb fastmult edsp java # ./pi_android 10000 Calculation of PI using FFT and AGM, ver. LG1.1.2-MP1.5.2a.memsave ... 5.95 sec. (real time) So it seems that the ARM926EJ-S is slower than my Android phone, but not twice slower as I would expect by the BogoMIPS figures. I am still unsure about the clock speed of the ARM9 CPU.

    Read the article

  • How do you monitor SSD wear in Windows when the drives are presented as 'generic' devices?

    - by MikeyB
    Under Linux, we can monitor SSD wear fairly easily with smartmontools whether the drive is presented as a normal block device or a generic device (which happens when the drive has been hardware RAIDed by certain controllers such as the one on the IBM HS22). How can we do the equivalent under Windows? Does anyone actually use smartmontools? Or are there other packages out there? The problem is that SCSI Generic devices just don't show up in Windows. If the drives aren't RAIDed we can see them fine. How I'd do it in Linux: sles11-live:~ # lsscsi -g [1:0:0:0] disk SMART USB-IBM 8989 /dev/sda /dev/sg0 [2:0:0:0] disk ATA MTFDDAK256MAR-1K MA44 - /dev/sg1 [2:0:1:0] disk ATA MTFDDAK256MAR-1K MA44 - /dev/sg2 [2:1:8:0] disk LSILOGIC Logical Volume 3000 /dev/sdb /dev/sg3 sles11-live:~ # smartctl -l ssd /dev/sg1 smartctl 5.42 2011-10-20 r3458 [x86_64-linux-2.6.32.49-0.3-default] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net Device Statistics (GP Log 0x04) Page Offset Size Value Description 7 ===== = = == Solid State Device Statistics (rev 1) == 7 0x008 1 26~ Percentage Used Endurance Indicator |_ ~ normalized value sles11-live:~ # smartctl -l ssd /dev/sg2 smartctl 5.42 2011-10-20 r3458 [x86_64-linux-2.6.32.49-0.3-default] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net Device Statistics (GP Log 0x04) Page Offset Size Value Description 7 ===== = = == Solid State Device Statistics (rev 1) == 7 0x008 1 3~ Percentage Used Endurance Indicator |_ ~ normalized value

    Read the article

  • The RTL8111/8168B NIC under Linux and the r8168 driver

    - by nik
    So I've got one of the infamous R8168 Realtek ethernet NIC, which have some problems under Linux. After some research, I found out I had to use the r8168 driver for this card (and not the r8169 which still loads when nothing else is available), which I did. So now everything works fine... Sort of. My download and upload rates are more than halved compared to what I should get. When I test (with eg. speedtest) I get something like 20M (often 15M) in download and 30M in upload, but if I test under Windows (everything is otherwise identical: same ethernet cable, same connection, at the same time of the day (well 5 min apart)...), I get 50M upload/download (which is what I expect). Where can it come from? Here's some info: ~ # lspci [...] 06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) ~ # modinfo r8168 filename: /lib/modules/3.2.1-gentoo-r2/net/r8168.ko version: 8.027.00-NAPI license: GPL description: RealTek RTL-8168 Gigabit Ethernet driver author: Realtek and the Linux r8168 crew <[email protected]> srcversion: 0A6E9F1D4E8E51DE4B6BEE3 alias: pci:v00001186d00004300sv00001186sd00004B10bc*sc*i* alias: pci:v000010ECd00008168sv*sd*bc*sc*i* depends: vermagic: 3.2.1-gentoo-r2 SMP mod_unload [...] ~ # mii-tool -v eth0: negotiated 100baseTx-HD, link ok product info: vendor 00:07:32, model 17 rev 4 basic mode: autonegotiation enabled basic status: autonegotiation complete, link ok capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 100baseTx-HD 10baseT-FD 10baseT-HD flow-control link partner: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD

    Read the article

  • How to disable mod_security2 rule (false positive) for one domain on centos 5

    - by nicholas.alipaz
    Hi I have mod_security enabled on a centos5 server and one of the rules is keeping a user from posting some text on a form. The text is legitimate but it has the words 'create' and an html <table> tag later in it so it is causing a false positive. The error I am receiving is below: [Sun Apr 25 20:36:53 2010] [error] [client 76.171.171.xxx] ModSecurity: Access denied with code 500 (phase 2). Pattern match "((alter|create|drop)[[:space:]]+(column|database|procedure|table)|delete[[:space:]]+from|update.+set.+=)" at ARGS:body. [file "/usr/local/apache/conf/modsec2.user.conf"] [line "352"] [id "300015"] [rev "1"] [msg "Generic SQL injection protection"] [severity "CRITICAL"] [hostname "www.mysite.com"] [uri "/node/181/edit"] [unique_id "@TaVDEWnlusAABQv9@oAAAAD"] and here is /usr/local/apache/conf/modsec2.user.conf (line 352) #Generic SQL sigs SecRule ARGS "((alter|create|drop)[[:space:]]+(column|database|procedure|table)|delete[[:space:]]+from|update.+set.+=)" "id:1,rev:1,severity:2,msg:'Generic SQL injection protection'" The questions I have are: What should I do to "whitelist" or allow this rule to get through? What file do I create and where? How should I alter this rule? Can I set it to only be allowed for the one domain, since it is the only one having the issue on this dedicated server or is there a better way to exclude table tags perhaps? Thanks guys

    Read the article

  • NIC are not advertising Correct Speeds

    - by Squidly
    I have an IBM x336 that is not advertising the proper LINK speeds. One interface is the other is not. I've tried to Force it to 1000/Full but then it just shows link down. I have confirmed the switch is set to auto negotiate like my switches. I have also changed out my Ethernet Cables. I'm at a loss where to look further. I have verified that it will connect at 1G on a different swtich. This also has happened on two different servers on the same switch. This is my output from mii-tool -v for each interface. eth0: negotiated 100baseTx-FD, link ok product info: vendor 00:08:18, model 24 rev 0 basic mode: autonegotiation enabled basic status: autonegotiation complete, link ok capabilities: 1000baseT-HD 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control link partner: 1000baseT-HD 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD eth1: negotiated 1000baseT-FD flow-control, link ok product info: vendor 00:08:18, model 24 rev 0 basic mode: autonegotiation enabled basic status: autonegotiation complete, link ok capabilities: 1000baseT-HD 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control link partner: 1000baseT-HD 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD

    Read the article

  • Windows 7 hangs after going into sleep a second time

    - by Brian Stephenson
    I've searched everywhere around Google and can't figure out why this is happening so I decide to ask here to see if anyone has a problem like this. Like it says in the title, whenever I sleep ONCE I'm able to wake the system, but going back to sleep again AFTER waking up for the first time results in it hanging on no input and no output, with the fan spinning as fast as possible and alot of heat being spewed out by the fan as well. I've tried various things like setting all USB Hub Root's to not get switched off for power saving, disabling USB selective suspend, disabling PCI-e link state power management, and even unplugging ALL USB devices and it wont wake up after the second attempt. And I've even waited up to a full hour of the CPU fan spinning loudly and it's still stuck trying to wake up. The only USB devices I use are a Microsoft USB Comfort Curve Keyboard 2000 (IntelliType Pro) and a generic HID compliant mouse from Creative model number OMC90S "CREATIVE MOUSE OPTICAL LITE". My other devices like external drives and controllers are unplugged when I'm not using them as having too many USB devices plugged in at a time causes a deadlock on almost all of the ports I have. Here's my system specifications (Most of these are from CPU-Z): Brand: Gateway DX4300-19 Mainboard: Gateway RS780 Chipset: AMD 780G Rev 00 Southbridge: AMD SB700 Rev 00 LPCIO: ITE IT8718 BIOS: American Megatrends Inc. ver P01-A4 09/15/2009 CPU: AMD Phenom II X4 810 at 2.60 GHz RAM: 8.0 GB DDR2 Dual Channel Ganged Mode at 400 MHz GPU: ATI Radeon HD3200 Graphics Intergrated - RS780 OS: Windows 7 Home Premium x64 OEM (Acer Group) HDD: WDC WD10EADS-22M2B0 1.0 TB (Western Digital Green Caviar) My BIOS has absolutely no control over how I setup the sleep mode to be either S1 or S3. So I can't check these settings or even change them. Hybrid sleep is also disabled, I can successfully go into hibernation and wake from hibernation but this is painfully slow due to a harddrive problem I'm having with this "Green Drive". (Hibernation takes over ~3 minutes to complete) Any help would be appreciated, thanks.

    Read the article

  • Can't reach only certain websites from my Wifi (with macbook and iphone)

    - by mellin
    I can't access certain websites neither from my macbook nor from my iphone when connected to my Wifi. The same website can be opened from another windows computer connected to the same Wifi. This is what happens when I try to ping it: PING ilpost.it (151.1.175.113): 56 data bytes Request timeout for icmp_seq 0 Request timeout for icmp_seq 1 Request timeout for icmp_seq 2 ... And when I try to traceroute it: host-001:~ j$ traceroute www.ilpost.it traceroute to ilpost.it (151.1.175.113), 64 hops max, 52 byte packets 1 vodafonedslrouter (192.168.1.1) 2.965 ms 0.743 ms 0.745 ms 2 * 2.96.54.77.rev.vodafone.pt (77.54.96.2) 12.076 ms 10.871 ms 3 77.41.30.213.rev.vodafone.pt (213.30.41.77) 14.145 ms 10.693 ms 11.960 ms 4 85.205.11.49 (85.205.11.49) 9.658 ms 8.946 ms 9.085 ms 5 85.205.13.105 (85.205.13.105) 57.497 ms 57.621 ms 48.080 ms 6 188.111.129.17 (188.111.129.17) 49.483 ms 51.338 ms 48.852 ms 7 85.205.25.174 (85.205.25.174) 47.891 ms 49.219 ms 47.821 ms 8 * * * 9 * * * 10 * * * 11 * * * I've flushed my DNS cache but nothing changed. This is quite dramatic as it seems to depend on 85.205.25.174 hop and don't know how to avoid it. Any suggestions? I add that 3 days ago everything worked fine. Then it has stopped.

    Read the article

  • Can't reach only certain websites from my Wifi (with macbook and iphone)

    - by trampj
    I can't access certain websites neither from my macbook nor from my iphone when connected to my Wifi. The same website can be opened from another windows computer connected to the same Wifi. This is what happens when I try to ping it: PING ilpost.it (151.1.175.113): 56 data bytes Request timeout for icmp_seq 0 Request timeout for icmp_seq 1 Request timeout for icmp_seq 2 ... And when I try to traceroute it: host-001:~ j$ traceroute www.ilpost.it traceroute to ilpost.it (151.1.175.113), 64 hops max, 52 byte packets 1 vodafonedslrouter (192.168.1.1) 2.965 ms 0.743 ms 0.745 ms 2 * 2.96.54.77.rev.vodafone.pt (77.54.96.2) 12.076 ms 10.871 ms 3 77.41.30.213.rev.vodafone.pt (213.30.41.77) 14.145 ms 10.693 ms 11.960 ms 4 85.205.11.49 (85.205.11.49) 9.658 ms 8.946 ms 9.085 ms 5 85.205.13.105 (85.205.13.105) 57.497 ms 57.621 ms 48.080 ms 6 188.111.129.17 (188.111.129.17) 49.483 ms 51.338 ms 48.852 ms 7 85.205.25.174 (85.205.25.174) 47.891 ms 49.219 ms 47.821 ms 8 * * * 9 * * * 10 * * * 11 * * * I've flushed my DNS cache but nothing changed. This is quite dramatic as it seems to depend on 85.205.25.174 hop and don't know how to avoid it. Any suggestions? I add that 3 days ago everything worked fine. Then it has stopped.

    Read the article

  • Python script is exiting with no output and I have no idea why

    - by Adam Tuttle
    I'm attempting to debug a Subversion post-commit hook that calls some python scripts. What I've been able to determine so far is that when I run post-commit.bat manually (I've created a wrapper for it to make it easier) everything succeeds, but when SVN runs it one particular step doesn't work. We're using CollabNet SVNServe, which I know from the documentation removes all environment variables. This had caused some problems earlier, but shouldn't be an issue now. Before Subversion calls a hook script, it removes all variables - including $PATH on Unix, and %PATH% on Windows - from the environment. Therefore, your script can only run another program if you spell out that program's absolute name. The relevant portion of post-commit.bat is: echo -------------------------- >> c:\svn-repos\company\hooks\svn2ftp.out.log set SITENAME=staging set SVNPATH=branches/staging/wwwroot/ "C:\Python3\python.exe" C:\svn-repos\company\hooks\svn2ftp.py ^ --svnUser="svnusername" ^ --svnPass="svnpassword" ^ --ftp-user=ftpuser ^ --ftp-password=ftppassword ^ --ftp-remote-dir=/ ^ --access-url=svn://10.0.100.6/company ^ --status-file="C:\svn-repos\company\hooks\svn2ftp-%SITENAME%.dat" ^ --project-directory=%SVNPATH% "staging.company.com" %1 %2 >> c:\svn-repos\company\hooks\svn2ftp.out.log echo -------------------------- >> c:\svn-repos\company\hooks\svn2ftp.out.log When I run post-commit.bat manually, for example: post-commit c:\svn-repos\company 12345, I see output like the following in svn2ftp.out.log: -------------------------- args1: c:\svn-repos\company args0: staging.company.com abspath: c:\svn-repos\company project_dir: branches/staging/wwwroot/ local_repos_path: c:\svn-repos\company getting youngest revision... done, up-to-date -------------------------- However, when I commit something to the repo and it runs automatically, the output is: -------------------------- -------------------------- svn2ftp.py is a bit long, so I apologize but here goes. I'll have some notes/disclaimers about its contents below it. #!/usr/bin/env python """Usage: svn2ftp.py [OPTION...] FTP-HOST REPOS-PATH Upload to FTP-HOST changes committed to the Subversion repository at REPOS-PATH. Uses svn diff --summarize to only propagate the changed files Options: -?, --help Show this help message. -u, --ftp-user=USER The username for the FTP server. Default: 'anonymous' -p, --ftp-password=P The password for the FTP server. Default: '@' -P, --ftp-port=X Port number for the FTP server. Default: 21 -r, --ftp-remote-dir=DIR The remote directory that is expected to resemble the repository project directory -a, --access-url=URL This is the URL that should be used when trying to SVN export files so that they can be uploaded to the FTP server -s, --status-file=PATH Required. This script needs to store the last successful revision that was transferred to the server. PATH is the location of this file. -d, --project-directory=DIR If the project you are interested in sending to the FTP server is not under the root of the repository (/), set this parameter. Example: -d 'project1/trunk/' This should NOT start with a '/'. 2008.5.2 CKS Fixed possible Windows-related bug with tempfile, where the script didn't have permission to write to the tempfile. Replaced this with a open()-created file created in the CWD. 2008.5.13 CKS Added error logging. Added exception for file-not-found errors when deleting files. 2008.5.14 CKS Change file open to 'rb' mode, to prevent Python's universal newline support from stripping CR characters, causing later comparisons between FTP and SVN to report changes. """ try: import sys, os import logging logging.basicConfig( level=logging.DEBUG, format='%(asctime)s %(levelname)s %(message)s', filename='svn2ftp.debug.log', filemode='a' ) console = logging.StreamHandler() console.setLevel(logging.ERROR) logging.getLogger('').addHandler(console) import getopt, tempfile, smtplib, traceback, subprocess from io import StringIO import pysvn import ftplib import inspect except Exception as e: logging.error(e) #capture the location of the error frame = inspect.currentframe() stack_trace = traceback.format_stack(frame) logging.debug(stack_trace) print(stack_trace) #end capture sys.exit(1) #defaults host = "" user = "anonymous" password = "@" port = 21 repo_path = "" local_repos_path = "" status_file = "" project_directory = "" remote_base_directory = "" toAddrs = "[email protected]" youngest_revision = "" def email(toAddrs, message, subject, fromAddr='[email protected]'): headers = "From: %s\r\nTo: %s\r\nSubject: %s\r\n\r\n" % (fromAddr, toAddrs, subject) message = headers + message logging.info('sending email to %s...' % toAddrs) server = smtplib.SMTP('smtp.company.com') server.set_debuglevel(1) server.sendmail(fromAddr, toAddrs, message) server.quit() logging.info('email sent') def captureErrorMessage(e): sout = StringIO() traceback.print_exc(file=sout) errorMessage = '\n'+('*'*80)+('\n%s'%e)+('\n%s\n'%sout.getvalue())+('*'*80) return errorMessage def usage_and_exit(errmsg): """Print a usage message, plus an ERRMSG (if provided), then exit. If ERRMSG is provided, the usage message is printed to stderr and the script exits with a non-zero error code. Otherwise, the usage message goes to stdout, and the script exits with a zero errorcode.""" if errmsg is None: stream = sys.stdout else: stream = sys.stderr print(__doc__, file=stream) if errmsg: print("\nError: %s" % (errmsg), file=stream) sys.exit(2) sys.exit(0) def read_args(): global host global user global password global port global repo_path global local_repos_path global status_file global project_directory global remote_base_directory global youngest_revision try: opts, args = getopt.gnu_getopt(sys.argv[1:], "?u:p:P:r:a:s:d:SU:SP:", ["help", "ftp-user=", "ftp-password=", "ftp-port=", "ftp-remote-dir=", "access-url=", "status-file=", "project-directory=", "svnUser=", "svnPass=" ]) except getopt.GetoptError as msg: usage_and_exit(msg) for opt, arg in opts: if opt in ("-?", "--help"): usage_and_exit() elif opt in ("-u", "--ftp-user"): user = arg elif opt in ("-p", "--ftp-password"): password = arg elif opt in ("-SU", "--svnUser"): svnUser = arg elif opt in ("-SP", "--svnPass"): svnPass = arg elif opt in ("-P", "--ftp-port"): try: port = int(arg) except ValueError as msg: usage_and_exit("Invalid value '%s' for --ftp-port." % (arg)) if port < 1 or port > 65535: usage_and_exit("Value for --ftp-port must be a positive integer less than 65536.") elif opt in ("-r", "--ftp-remote-dir"): remote_base_directory = arg elif opt in ("-a", "--access-url"): repo_path = arg elif opt in ("-s", "--status-file"): status_file = os.path.abspath(arg) elif opt in ("-d", "--project-directory"): project_directory = arg if len(args) != 3: print(str(args)) usage_and_exit("host and/or local_repos_path not specified (" + len(args) + ")") host = args[0] print("args1: " + args[1]) print("args0: " + args[0]) print("abspath: " + os.path.abspath(args[1])) local_repos_path = os.path.abspath(args[1]) print('project_dir:',project_directory) youngest_revision = int(args[2]) if status_file == "" : usage_and_exit("No status file specified") def main(): global host global user global password global port global repo_path global local_repos_path global status_file global project_directory global remote_base_directory global youngest_revision read_args() #repository,fs_ptr #get youngest revision print("local_repos_path: " + local_repos_path) print('getting youngest revision...') #youngest_revision = fs.youngest_rev(fs_ptr) assert youngest_revision, "Unable to lookup youngest revision." last_sent_revision = get_last_revision() if youngest_revision == last_sent_revision: # no need to continue. we should be up to date. print('done, up-to-date') return if last_sent_revision or youngest_revision < 10: # Only compare revisions if the DAT file contains a valid # revision number. Otherwise we risk waiting forever while # we parse and uploading every revision in the repo in the case # where a repository is retroactively configured to sync with ftp. pysvn_client = pysvn.Client() pysvn_client.callback_get_login = get_login rev1 = pysvn.Revision(pysvn.opt_revision_kind.number, last_sent_revision) rev2 = pysvn.Revision(pysvn.opt_revision_kind.number, youngest_revision) summary = pysvn_client.diff_summarize(repo_path, rev1, repo_path, rev2, True, False) print('summary len:',len(summary)) if len(summary) > 0 : print('connecting to %s...' % host) ftp = FTPClient(host, user, password) print('connected to %s' % host) ftp.base_path = remote_base_directory print('set remote base directory to %s' % remote_base_directory) #iterate through all the differences between revisions for change in summary : #determine whether the path of the change is relevant to the path that is being sent, and modify the path as appropriate. print('change path:',change.path) ftp_relative_path = apply_basedir(change.path) print('ftp rel path:',ftp_relative_path) #only try to sync path if the path is in our project_directory if ftp_relative_path != "" : is_file = (change.node_kind == pysvn.node_kind.file) if str(change.summarize_kind) == "delete" : print("deleting: " + ftp_relative_path) try: ftp.delete_path("/" + ftp_relative_path, is_file) except ftplib.error_perm as e: if 'cannot find the' in str(e) or 'not found' in str(e): # Log, but otherwise ignore path-not-found errors # when deleting, since it's not a disaster if the file # we want to delete is already gone. logging.error(captureErrorMessage(e)) else: raise elif str(change.summarize_kind) == "added" or str(change.summarize_kind) == "modified" : local_file = "" if is_file : local_file = svn_export_temp(pysvn_client, repo_path, rev2, change.path) print("uploading file: " + ftp_relative_path) ftp.upload_path("/" + ftp_relative_path, is_file, local_file) if is_file : os.remove(local_file) elif str(change.summarize_kind) == "normal" : print("skipping 'normal' element: " + ftp_relative_path) else : raise str("Unknown change summarize kind: " + str(change.summarize_kind) + ", path: " + ftp_relative_path) ftp.close() #write back the last revision that was synced print("writing last revision: " + str(youngest_revision)) set_last_revision(youngest_revision) # todo: undo def get_login(a,b,c,d): #arguments don't matter, we're always going to return the same thing try: return True, "svnUsername", "svnPassword", True except Exception as e: logging.error(e) #capture the location of the error frame = inspect.currentframe() stack_trace = traceback.format_stack(frame) logging.debug(stack_trace) #end capture sys.exit(1) #functions for persisting the last successfully synced revision def get_last_revision(): if os.path.isfile(status_file) : f=open(status_file, 'r') line = f.readline() f.close() try: i = int(line) except ValueError: i = 0 else: i = 0 f = open(status_file, 'w') f.write(str(i)) f.close() return i def set_last_revision(rev) : f = open(status_file, 'w') f.write(str(rev)) f.close() #augmented ftp client class that can work off a base directory class FTPClient(ftplib.FTP) : def __init__(self, host, username, password) : self.base_path = "" self.current_path = "" ftplib.FTP.__init__(self, host, username, password) def cwd(self, path) : debug_path = path if self.current_path == "" : self.current_path = self.pwd() print("pwd: " + self.current_path) if not os.path.isabs(path) : debug_path = self.base_path + "<" + path path = os.path.join(self.current_path, path) elif self.base_path != "" : debug_path = self.base_path + ">" + path.lstrip("/") path = os.path.join(self.base_path, path.lstrip("/")) path = os.path.normpath(path) #by this point the path should be absolute. if path != self.current_path : print("change from " + self.current_path + " to " + debug_path) ftplib.FTP.cwd(self, path) self.current_path = path else : print("staying put : " + self.current_path) def cd_or_create(self, path) : assert os.path.isabs(path), "absolute path expected (" + path + ")" try: self.cwd(path) except ftplib.error_perm as e: for folder in path.split('/'): if folder == "" : self.cwd("/") continue try: self.cwd(folder) except: print("mkd: (" + path + "):" + folder) self.mkd(folder) self.cwd(folder) def upload_path(self, path, is_file, local_path) : if is_file: (path, filename) = os.path.split(path) self.cd_or_create(path) # Use read-binary to avoid universal newline support from stripping CR characters. f = open(local_path, 'rb') self.storbinary("STOR " + filename, f) f.close() else: self.cd_or_create(path) def delete_path(self, path, is_file) : (path, filename) = os.path.split(path) print("trying to delete: " + path + ", " + filename) self.cwd(path) try: if is_file : self.delete(filename) else: self.delete_path_recursive(filename) except ftplib.error_perm as e: if 'The system cannot find the' in str(e) or '550 File not found' in str(e): # Log, but otherwise ignore path-not-found errors # when deleting, since it's not a disaster if the file # we want to delete is already gone. logging.error(captureErrorMessage(e)) else: raise def delete_path_recursive(self, path): if path == "/" : raise "WARNING: trying to delete '/'!" for node in self.nlst(path) : if node == path : #it's a file. delete and return self.delete(path) return if node != "." and node != ".." : self.delete_path_recursive(os.path.join(path, node)) try: self.rmd(path) except ftplib.error_perm as msg : sys.stderr.write("Error deleting directory " + os.path.join(self.current_path, path) + " : " + str(msg)) # apply the project_directory setting def apply_basedir(path) : #remove any leading stuff (in this case, "trunk/") and decide whether file should be propagated if not path.startswith(project_directory) : return "" return path.replace(project_directory, "", 1) def svn_export_temp(pysvn_client, base_path, rev, path) : # Causes access denied error. Couldn't deduce Windows-perm issue. # It's possible Python isn't garbage-collecting the open file-handle in time for pysvn to re-open it. # Regardless, just generating a simple filename seems to work. #(fd, dest_path) = tempfile.mkstemp() dest_path = tmpName = '%s.tmp' % __file__ exportPath = os.path.join(base_path, path).replace('\\','/') print('exporting %s to %s' % (exportPath, dest_path)) pysvn_client.export( exportPath, dest_path, force=False, revision=rev, native_eol=None, ignore_externals=False, recurse=True, peg_revision=rev ) return dest_path if __name__ == "__main__": logging.info('svnftp.start') try: main() logging.info('svnftp.done') except Exception as e: # capture the location of the error for debug purposes frame = inspect.currentframe() stack_trace = traceback.format_stack(frame) logging.debug(stack_trace[:-1]) print(stack_trace) # end capture error_text = '\nFATAL EXCEPTION!!!\n'+captureErrorMessage(e) subject = "ALERT: SVN2FTP Error" message = """An Error occurred while trying to FTP an SVN commit. repo_path = %(repo_path)s\n local_repos_path = %(local_repos_path)s\n project_directory = %(project_directory)s\n remote_base_directory = %(remote_base_directory)s\n error_text = %(error_text)s """ % globals() email(toAddrs, message, subject) logging.error(e) Notes/Disclaimers: I have basically no python training so I'm learning as I go and spending lots of time reading docs to figure stuff out. The body of get_login is in a try block because I was getting strange errors saying there was an unhandled exception in callback_get_login. Never figured out why, but it seems fine now. Let sleeping dogs lie, right? The username and password for get_login are currently hard-coded (but correct) just to eliminate variables and try to change as little as possible at once. (I added the svnuser and svnpass arguments to the existing argument parsing.) So that's where I am. I can't figure out why on earth it's not printing anything into svn2ftp.out.log. If you're wondering, the output for one of these failed attempts in svn2ftp.debug.log is: 2012-09-06 15:18:12,496 INFO svnftp.start 2012-09-06 15:18:12,496 INFO svnftp.done And it's no different on a successful run. So there's nothing useful being logged. I'm lost. I've gone way down the rabbit hole on this one, and don't know where to go from here. Any ideas?

    Read the article

  • Ubuntu 10.04 recognizing USB 2.0 external HD as USB 1.1

    - by btucker
    When I connect the USB 2.0 drive I see this: usb 1-4.3: new full speed USB device using ohci_hcd and address 5 so I know it's getting seen as USB 1.1. usb-devices shows that it really is USB 2.0 and connected to a USB 2.0 hub: T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 2 Spd=12 MxCh= 4 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=05e3 ProdID=0608 Rev=77.61 S: Product=USB2.0 Hub C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=13fd ProdID=1340 Rev=02.10 S: Manufacturer=Generic S: Product=External C: #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=2mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage It seems the problem is that root hub is: T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh=10 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0001 Rev=02.06 S: Manufacturer=Linux 2.6.32-25-server ohci_hcd S: Product=OHCI Host Controller S: SerialNumber=0000:00:02.0 C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub And there's no mention of ehci_hcd. lsusb -t gives me: /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=ohci_hcd/10p, 12M |__ Port 4: Dev 2, If 0, Class=hub, Driver=hub/4p, 12M |__ Port 2: Dev 4, If 0, Class=stor., Driver=usb-storage, 12M |__ Port 3: Dev 5, If 0, Class=stor., Driver=usb-storage, 12M |__ Port 6: Dev 3, If 0, Class=stor., Driver=usb-storage, 12M It seems like I'm missing something which would allow the OS to see USB 2.0 devices. Can anyone point me in the right direction? EDIT Full lsusb -v output: Bus 001 Device 005: ID 13fd:1340 Initio Corporation Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x13fd Initio Corporation idProduct 0x1340 bcdDevice 2.10 iManufacturer 1 Generic iProduct 2 External iSerial 3 57442D574341595930323337 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 32 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xc0 Self Powered MaxPower 2mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 8 Mass Storage bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk (Zip) iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0001 Self Powered Bus 001 Device 002: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 0 Full speed (or root) hub bMaxPacketSize0 64 idVendor 0x05e3 Genesys Logic, Inc. idProduct 0x0608 USB-2.0 4-Port HUB bcdDevice 77.61 iManufacturer 0 iProduct 1 USB2.0 Hub iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 100mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0001 1x 1 bytes bInterval 255 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x00e0 Ganged power switching Ganged overcurrent protection Port indicators bPwrOn2PwrGood 50 * 2 milli seconds bHubContrCurrent 100 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0103 power enable connect Port 3: 0000.0103 power enable connect Port 4: 0000.0100 power Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 1 Single TT bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0001 Self Powered Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 0 Full speed (or root) hub bMaxPacketSize0 64 idVendor 0x1d6b Linux Foundation idProduct 0x0001 1.1 root hub bcdDevice 2.06 iManufacturer 3 Linux 2.6.32-25-server ohci_hcd iProduct 2 OHCI Host Controller iSerial 1 0000:00:02.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0002 1x 2 bytes bInterval 255 Hub Descriptor: bLength 11 bDescriptorType 41 nNbrPorts 10 wHubCharacteristic 0x0002 No power switching (usb 1.0) Ganged overcurrent protection bPwrOn2PwrGood 1 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 0x00 PortPwrCtrlMask 0xff 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0103 power enable connect Port 5: 0000.0100 power Port 6: 0000.0103 power enable connect Port 7: 0000.0100 power Port 8: 0000.0100 power Port 9: 0000.0100 power Port 10: 0000.0100 power Device Status: 0x0003 Self Powered Remote Wakeup Enabled

    Read the article

  • Wireless will not connect

    - by azz0r
    Hello, I have installed Ubuntu 10.10 on the same machine as my windows setup. However, it will not connect to my wireless network. It can see its there, it can attempt to connect, yet it will never connect. It will keep bringing up the password prompt everyso often. I have tried turning my security to WEP, I ended up turning it back to WPA2. It is set to AES (noted a few threads on google about that). Can you assist? I would love to dive into Ubuntu, but without the internet its pointless. --- lshw -C network --- *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 02 serial: 00:1d:92:ea:cc:62 capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8168 driverversion=8.020.00-NAPI duplex=half latency=0 link=no multicast=yes port=twisted pair resources: irq:29 ioport:e800(size=256) memory:feaff000-feafffff memory:f8ff0000-f8ffffff(prefetchable) memory:feac0000-feadffff(prefetchable) *-network description: Wireless interface physical id: 1 logical name: wlan0 serial: 00:15:af:72:a4:38 capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=IEEE 802.11bgn --- iwconfig ---- lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"Wuggawoo" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Tx-Power=9 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on --- cat /etc/network/interfaces ---- auto lo iface lo inet loopback logs deamon.log --- Jan 19 04:17:09 ubuntu wpa_supplicant[1289]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 04:17:09 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:17:09 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:17:11 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:17:11 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:17:11 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0/wireless): association took too long. Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): device state change: 5 -> 6 (reason 0) Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0/wireless): asking for new secrets Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled... Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started... Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): device state change: 6 -> 4 (reason 0) Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled... Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete. Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting... Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): device state change: 4 -> 5 (reason 0) Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0/wireless): connection 'Wuggawoo' has security, and secrets exist. No new secrets needed. Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'ssid' value 'Wuggawoo' Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'scan_ssid' value '1' Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'key_mgmt' value 'WPA-PSK' Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'psk' value '<omitted>' Jan 19 04:17:12 ubuntu NetworkManager: nm_setting_802_1x_get_pkcs11_engine_path: assertion `NM_IS_SETTING_802_1X (setting)' failed Jan 19 04:17:12 ubuntu NetworkManager: nm_setting_802_1x_get_pkcs11_module_path: assertion `NM_IS_SETTING_802_1X (setting)' failed Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete. Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: set interface ap_scan to 1 Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:17:13 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:17:13 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:17:13 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:17:23 ubuntu wpa_supplicant[1289]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 04:17:23 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:17:23 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:17:24 ubuntu AptDaemon: INFO: Initializing daemon Jan 19 04:17:25 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:17:25 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:17:25 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:17:27 ubuntu NetworkManager: <info> wlan0: link timed out. --- kern.log --- Jan 19 04:18:11 ubuntu kernel: [ 142.420024] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out Jan 19 04:18:13 ubuntu kernel: [ 144.333847] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 1) Jan 19 04:18:13 ubuntu kernel: [ 144.539996] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 2) Jan 19 04:18:13 ubuntu kernel: [ 144.750027] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 3) Jan 19 04:18:14 ubuntu kernel: [ 144.940022] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out Jan 19 04:18:25 ubuntu kernel: [ 155.832995] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 1) Jan 19 04:18:25 ubuntu kernel: [ 156.030046] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 2) Jan 19 04:18:25 ubuntu kernel: [ 156.230039] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 3) Jan 19 04:18:25 ubuntu kernel: [ 156.430039] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out --- syslog --- Jan 19 04:18:46 ubuntu wpa_supplicant[1289]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 04:18:46 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:18:46 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:18:48 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:18:48 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:18:48 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:18:48 ubuntu kernel: [ 178.833905] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 1) Jan 19 04:18:48 ubuntu kernel: [ 179.030035] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 2) Jan 19 04:18:48 ubuntu kernel: [ 179.230020] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 3) Jan 19 04:18:48 ubuntu kernel: [ 179.433634] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out lspci and lsusb lspci -- 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge 00:02.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (ext gfx port 0) 00:05.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 1) 00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) 00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] 00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:12.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:12.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:13.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:13.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3a) 00:14.1 IDE interface: ATI Technologies Inc SB700/SB800 IDE Controller 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:14.5 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 01:00.0 VGA compatible controller: nVidia Corporation G80 [GeForce 8800 GTS] (rev a2) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) 03:00.0 FireWire (IEEE 1394): JMicron Technology Corp. IEEE 1394 Host Controller -- lsusb -- Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 003: ID 046d:c517 Logitech, Inc. LX710 Cordless Desktop Laser Bus 004 Device 002: ID 045e:0730 Microsoft Corp. Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 003: ID 13d3:3247 IMC Networks 802.11 n/g/b Wireless LAN Adapter Bus 002 Device 002: ID 0718:0628 Imation Corp. Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 046d:08c2 Logitech, Inc. QuickCam PTZ Bus 001 Device 002: ID 0424:2228 Standard Microsystems Corp. 9-in-2 Card Reader Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub With no security on my router I still can't connect, I get: Jan 19 15:58:01 ubuntu wpa_supplicant[1165]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 15:58:01 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 15:58:01 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 15:58:02 ubuntu wpa_supplicant[1165]: WPS-AP-AVAILABLE Jan 19 15:58:02 ubuntu wpa_supplicant[1165]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 15:58:02 ubuntu wpa_supplicant[1165]: Association request to the driver failed Jan 19 15:58:02 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 15:58:05 ubuntu NetworkManager: <info> wlan0: link timed out. Jan 19 15:58:07 ubuntu wpa_supplicant[1165]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 15:58:07 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 15:58:07 ubuntu NetworkManager: <info> (wlan0): supplicant connec

    Read the article

  • racoon-tool doesn't generate full racoon.conf file in /var/lib/racoon/racoon.conf

    - by robthewolf
    I am using ipsec-tools/racoon to create my VPN. I am using racoon-tool to configure racoon.conf but when I run racoon-tool reload it only generates the first section - Global items. When I run racoon-tool I get: # racoon-tool reload Loading SAD and SPD... SAD and SPD loaded. Configuring racoon...done. This is the entire file /var/lib/racoon/racoon.conf # # Racoon configuration for Samuel # Generated on Wed Jan 5 21:31:49 2011 by racoon-tool # # # Global items # path pre_shared_key "/etc/racoon/psk.txt"; path certificate "/etc/racoon/certs"; log debug; I cannot find anywhere a solution as to why this is happening. Please help

    Read the article

  • racoon-tool doesn't generate full racoon.conf file in /var/lib/racoon/racoon.conf

    - by robthewolf
    I am using ipsec-tools/racoon to create my VPN. I am using racoon-tool to configure racoon.conf but when I run racoon-tool reload it only generates the first section - Global items. When I run racoon-tool I get: # racoon-tool reload Loading SAD and SPD... SAD and SPD loaded. Configuring racoon...done. This is the entire file /var/lib/racoon/racoon.conf # # Racoon configuration for Samuel # Generated on Wed Jan 5 21:31:49 2011 by racoon-tool # # # Global items # path pre_shared_key "/etc/racoon/psk.txt"; path certificate "/etc/racoon/certs"; log debug; I cannot find anywhere a solution as to why this is happening. Please help

    Read the article

  • No more internet connection after update in 14.04 with Intel Dual Band Wireless AC 7260

    - by luis
    My Dell XPS 15 (haswell) was working fine until I stupidly accepted recently to apply Ubuntu updates. Since then, my wifi does not work (it shows "device not managed" when clicking wifi icon in toolbar). Even USB to Ethernet adapter does not seem to work. Bluetooth at least "sees" other bluetooth devices around... See below output from dmesg (dmesg |grep iwl) : [ 886.462459] iwlwifi 0000:06:00.0: irq 51 for MSI/MSI-X [ 886.462561] iwlwifi 0000:06:00.0: Direct firmware load failed with error -2 [ 886.462562] iwlwifi 0000:06:00.0: Falling back to user helper [ 886.463284] iwlwifi 0000:06:00.0: loaded firmware version 22.1.7.0 op_mode iwlmvm [ 886.475345] iwlwifi 0000:06:00.0: Detected Intel(R) Dual Band Wireless AC 7260, REV=0x144 [ 886.475433] iwlwifi 0000:06:00.0: L1 Enabled; Disabling L0S [ 886.475684] iwlwifi 0000:06:00.0: L1 Enabled; Disabling L0S [ 886.689214] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs' Below the output from modinfo iwlwifi: filename: /lib/modules/3.13.0-29- generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko license: GPL author: Copyright(c) 2003-2013 Intel Corporation <[email protected]> version: in-tree: description: Intel(R) Wireless WiFi driver for Linux firmware: iwlwifi-100-5.ucode firmware: iwlwifi-1000-5.ucode firmware: iwlwifi-135-6.ucode firmware: iwlwifi-105-6.ucode firmware: iwlwifi-2030-6.ucode firmware: iwlwifi-2000-6.ucode firmware: iwlwifi-5150-2.ucode firmware: iwlwifi-5000-5.ucode firmware: iwlwifi-6000g2b-6.ucode firmware: iwlwifi-6000g2a-5.ucode firmware: iwlwifi-6050-5.ucode firmware: iwlwifi-6000-4.ucode firmware: iwlwifi-3160-7.ucode firmware: iwlwifi-7260-7.ucode srcversion: 1E6912E109D5A43B310FB34 alias: pci:v00008086d0000095Asv*sd00005490bc*sc*i* (a pack of lines of kind "alias: pci:xxxxx...." that I guess are not helpful) alias: pci:v00008086d0000095Bsv*sd00005290bc*sc*i* depends: cfg80211 intree: Y vermagic: 3.13.0-29-generic SMP mod_unload modversions signer: Magrathea: Glacier signing key sig_key: 66:02:CB:36:F1:31:3B:EA:01:C4:BD:A9:65:67:CF:A7:23:C9:70:D8 sig_hashalgo: sha512 parm: swcrypto:using crypto in software (default 0 [hardware]) (int) parm: 11n_disable:disable 11n functionality, bitmap: 1: full, 2: disable agg TX, 4: disable agg RX, 8 enable agg TX (uint) parm: amsdu_size_8K:enable 8K amsdu size (default 0) (int) parm: fw_restart:restart firmware in case of error (default true) (bool) parm: antenna_coupling:specify antenna coupling in dB (defualt: 0 dB) (int) parm: wd_disable:Disable stuck queue watchdog timer 0=system default, 1=disable, 2=enable (default: 0) (int) parm: nvm_file:NVM file name (charp) parm: bt_coex_active:enable wifi/bt co-exist (default: enable) (bool) parm: led_mode:0=system default, 1=On(RF On)/Off(RF Off), 2=blinking, 3=Off (default: 0) (int) parm: power_save:enable WiFi power management (default: disable) (bool) parm: power_level:default power save level (range from 1 - 5, default: 1) (int) I downloaded the latest versions of iwlwifi firmware from git (git clone git://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git; copy iwlwifi-3160-9.ucode iwlwifi-7260-9.ucode iwlwifi-7265-9.ucode to /lib/firmware and reboot) but as you can imagine it did not help. Update #1: Downloaded from http://wireless.kernel.org/en/users/Drivers/iwlwifi?action=AttachFile&do=get&target=iwlwifi-7260-ucode-22.15.8.0.tgz and copied the file into /lib/firmware. After reloading it with modprobe, it seems to be OK: [ 14.761283] iwlwifi 0000:06:00.0: enabling device (0000 -> 0002) [ 14.761472] iwlwifi 0000:06:00.0: irq 51 for MSI/MSI-X [ 14.772478] iwlwifi 0000:06:00.0: loaded firmware version 22.15.8.0 op_mode iwlmvm [ 14.800274] iwlwifi 0000:06:00.0: Detected Intel(R) Dual Band Wireless AC 7260, REV=0x144 [ 14.800349] iwlwifi 0000:06:00.0: L1 Enabled; Disabling L0S [ 14.800657] iwlwifi 0000:06:00.0: L1 Enabled; Disabling L0S [ 15.007048] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs' However, clicking in wifi in the toolbar still shows "device not managed". Any clues? Many thanks! Luis

    Read the article

  • With WPF and Silverlight against cancer

    - by Laurent Bugnion
    MVPs are well known for their good heart (like the GeekGive initiative shows) and Client App Dev MVP Gregor Biswanger is no exception. At the latest MVP summit (beginning of March 2011), he took over a DVD about WPF 4 and Silverlight 4 and asked a few Microsoft superstars to sign it. Right now, the DVD is auctioned on eBay and of course the proceeds will go to a charitable work: The German League against Cancer (Deutsche Krebshilfe). The post is in German and English (scroll down for the English text). This sounds like a great idea, and considering who signed it, it is going to be a real collectible: Scott Hanselman (Principal Program Manager Lead in Server and Tools Online) Tim Heuer (Program Manager for Microsoft Silverlight) Rob Relyea (Principal Program Manager Lead - Client Platform WPF & Silverlight) Pete Brown (Developer Division Community Program Manager - Windows Client) Eric Fabricant (Program Manager WPF) Jeff Wilcox (Silverlight Senior SDE) Jeffrey R Ferman (SDET Visual Studio Client Dev Tools) Chan Verbeck (Expression Blend Team) Yaniv Feinberg (Expression Blend Team) Douglas Olson (Director Dev Expression) Samuel W. Bent (Principal Software Design Engineer WPF) John Papa (Technical Evangelist for Silverlight) So if you feel that you could do a generous gesture, go ahead and take a look at the auction, and talk about it around you. Let’s prove again that geeks rule, also when it comes to giving to a good cause! Cheers! Laurent   Laurent Bugnion (GalaSoft) Subscribe | Twitter | Facebook | Flickr | LinkedIn

    Read the article

  • Nec USB 3.0 controller drops connection - Ubuntu 12.04.1

    - by Tom
    I have some serious problems with Technaxx pci-e 302p card. It has uPD720200a NEC chip with 4020 firmware. BIOS recognises it. Sometimes it recognises devices and system mounts them and are functional for few minutes, other times they can't be mount and error occours. After fresh install card worked fine, but after kernel and firmware update it behaves as mentioned. Outputs: uname -a Linux asd-GA-MA770-UD3 3.2.0-30-generic #48-Ubuntu SMP Fri Aug 24 16:52:48 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux lspci -vvv USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) (prog-if 30 [XHCI]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at fd8fe000 (64-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: xhci_hcd lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 07d1:3c0a D-Link System DWA-140 RangeBooster N Adapter(rev.B2) [Ralink RT3072] Bus 005 Device 004: ID 1997:1221 Bus 005 Device 003: ID 15c2:003c SoundGraph Inc. lsmod Module Size Used by nls_iso8859_1 12713 0 nls_cp437 16991 0 vfat 17585 0 fat 61512 1 vfat vesafb 13844 1 saa7134_alsa 18602 1 rfcomm 47604 0 bnep 18281 2 bluetooth 180104 10 rfcomm,bnep tda827x 18182 1 snd_hda_codec_hdmi 32474 1 ir_lirc_codec 12859 0 lirc_dev 19204 1 ir_lirc_codec tda8290 22616 1 arc4 12529 2 snd_hda_codec_realtek 224173 1 ir_mce_kbd_decoder 12777 0 ir_sony_decoder 12510 0 ir_jvc_decoder 12507 0 tuner 27428 1 ir_rc6_decoder 12507 0 snd_hda_intel 33773 5 rt2800usb 22684 0 rt2800lib 58925 1 rt2800usb crc_ccitt 12667 1 rt2800lib rt2x00usb 20762 1 rt2800usb rt2x00lib 51144 3 rt2800usb,rt2800lib,rt2x00usb mac80211 506816 3 rt2800lib,rt2x00usb,rt2x00lib ir_rc5_decoder 12507 0 rc_avermedia_m135a 12526 0 rc_imon_pad 12505 0 ir_nec_decoder 12507 0 cfg80211 205544 2 rt2x00lib,mac80211 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_ctxfi 111202 2 snd_hwdep 13668 1 snd_hda_codec imon 32839 0 snd_pcm 97188 5 saa7134_alsa,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_ctxfi snd_seq_midi 13324 0 saa7134 181851 1 saa7134_alsa videobuf_dma_sg 19354 2 saa7134_alsa,saa7134 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi joydev 17693 0 rc_core 26412 13 ir_lirc_codec,ir_mce_kbd_decoder,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_rc5_decoder,rc_avermedia_m135a,rc_imon_pad,ir_nec_decoder,imon,saa7134 snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event fglrx 3263886 101 videobuf_core 26390 2 saa7134,videobuf_dma_sg v4l2_common 16454 2 tuner,saa7134 videodev 98259 3 tuner,saa7134,v4l2_common sp5100_tco 13791 0 snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 28 saa7134_alsa,snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_ctxfi,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device v4l2_compat_ioctl32 17128 1 videodev tveeprom 21249 1 saa7134 i2c_piix4 13301 0 soundcore 15091 1 snd edac_core 53746 0 serio_raw 13211 0 snd_page_alloc 18529 3 snd_hda_intel,snd_ctxfi,snd_pcm edac_mce_amd 23709 0 wmi 19256 0 mac_hid 13253 0 ppdev 17113 0 parport_pc 32866 1 k10temp 13166 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp usb_storage 49198 0 uas 18180 0 usbhid 47199 0 hid 99559 1 usbhid firewire_ohci 41000 0 firewire_core 63558 1 firewire_ohci crc_itu_t 12707 1 firewire_core floppy 70365 0 pata_atiixp 13204 2 r8169 62099 0 dmesg | tail after plugging to usb 3.0 port [ 834.871296] sd 9:0:0:0: rejecting I/O to offline device [ 834.871308] sd 9:0:0:0: rejecting I/O to offline device [ 834.871319] sd 9:0:0:0: rejecting I/O to offline device [ 834.871330] sd 9:0:0:0: rejecting I/O to offline device [ 834.871530] sd 9:0:0:0: [sdd] Unhandled error code [ 834.871536] sd 9:0:0:0: [sdd] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 834.871545] sd 9:0:0:0: [sdd] CDB: Read(10): 28 00 0e 8e 48 0a 00 00 3e 00 [ 834.871564] end_request: I/O error, dev sdd, sector 244205578 [ 834.875497] sd 8:0:0:1: Device offlined - not ready after error recovery [ 834.885339] usb 9-2: USB disconnect, device number 2 Are there any other outputs need for answering? I'll post them ASAP. I could of course reject updating the system but I think it's halfway solution. Any help appreciated. BTW USB 2.0 and 1.1 ports run well, card itself runs under win7 as charm. Tom

    Read the article

  • Yet another Subversion "Commit failed" MERGE of 'blabla': 200 OK

    - by marty3d
    Hi! I get the infamous "MERGE of 'whatever': 200 OK" whenever I try to commit using a post-commit hook on Windows (running the repository and Trac locally), and I'm going crazy. I've been looking all over for a day now, without finding any solutions. So here's how it's set up and what I've tried so far: Settings: Windows 7 (64-bit) VisualSVN Server TortoiseSVN Trac 0.11.6 I'm using the three standard scripts for post-commit on Windows. Everything works when I run post-commit.cmd from the command prompt with repo and changesetnumber as parameters. After extensive trouble-shooting, I found that if I remove the last line in trac-post-commit.cmd, Python "%~dp0\trac-post-commit-hook.py" -p "%TRAC_ENV%" -r "%REV%" -u "%AUTHOR%" -m "%LOG%", the Commit failed error goes away. Adding 1/0 (generating a division by zero error) in the python script doesn't show anything different. From the command prompt I get an error, though. Removing all code in the python script also makes the commit failed go away, so I guess the culprit is in trac-post-commit-hook.py. Perhaps if I could send the actual error to a log file, I could dig a little deeper, but I'm not sure how. post-commit.cmd: call %~dp0\trac-post-commit-hook.cmd %1 %2 trac-post-commit-hook.cmd: http://trac.edgewall.org/browser/trunk/contrib/trac-post-commit-hook?rev=920 Thank you so much, it would mean alot if someone could assist a little here! /Martin

    Read the article

  • mercurial .hgrc notify hook

    - by Eeyore
    Could someone tell me what is incorrect in my .hgrc configuration? I am trying to use gmail to send a e-mail after each push and/or commit. .hgrc [paths] default = ssh://www.domain.com/repo/hg [ui] username = intern <[email protected]> ssh="C:\Program Files (x86)\Mercurial\plink.exe" -ssh -i "C:\Program Files (x86)\Mercurial\key.pub" [extensions] hgext.notify = [hooks] changegroup.notify = python:hgext.notify.hook incoming.notify = python:hgext.notify.hook [email] from = [email protected] [smtp] host = smtp.gmail.com username = [email protected] password = sure port = 587 tls = true [web] baseurl = http://dev/... [notify] sources = serve push pull bundle test = False config = /path/to/subscription/file template = \ndetails: {baseurl}{webroot}/rev/{node|short}\nchangeset: {rev}:{node|short}\nuser: {author}\ndate: {date|date}\ndescription:\n{desc}\n maxdiff = 300 Error Incoming comand failed for P/project. running ""C:\Program Files (x86)\Mercurial\plink.exe" -ssh -i "C:\Program Files (x86)\Mercurial\key.pub" [email protected] "hg -R repo/hg serve --stdio"" sending hello command sending between command remote: FATAL ERROR: Server unexpectedly closed network connection abort: no suitable response from remote hg! , error code: -1 running ""C:\Program Files (x86)\Mercurial\plink.exe" -ssh -i "C:\Program Files (x86)\Mercurial\key.pub" [email protected] "hg -R repo/hg serve --stdio"" sending hello command sending between command remote: FATAL ERROR: Server unexpectedly closed network connection abort: no suitable response from remote hg!

    Read the article

  • Bubble sort algorithm implementations (Haskell vs. C)

    - by kingping
    Hello. I have written 2 implementation of bubble sort algorithm in C and Haskell. Haskell implementation: module Main where main = do contents <- readFile "./data" print "Data loaded. Sorting.." let newcontents = bubblesort contents writeFile "./data_new_ghc" newcontents print "Sorting done" bubblesort list = sort list [] False rev = reverse -- separated. To see rev2 = reverse -- who calls the routine sort (x1:x2:xs) acc _ | x1 > x2 = sort (x1:xs) (x2:acc) True sort (x1:xs) acc flag = sort xs (x1:acc) flag sort [] acc True = sort (rev acc) [] False sort _ acc _ = rev2 acc I've compared these two implementations having run both on file with size of 20 KiB. C implementation took about a second, Haskell — about 1 min 10 sec. I have also profiled the Haskell application: Compile for profiling: C:\Temp ghc -prof -auto-all -O --make Main Profile: C:\Temp Main.exe +RTS -p and got these results. This is a pseudocode of the algorithm: procedure bubbleSort( A : list of sortable items ) defined as: do swapped := false for each i in 0 to length(A) - 2 inclusive do: if A[i] > A[i+1] then swap( A[i], A[i+1] ) swapped := true end if end for while swapped end procedure I wonder if it's possible to make Haskell implementation work faster without changing the algorithm (there's are actually a few tricks to make it work faster, but neither implementations have these optimizations)

    Read the article

  • Ivy failed to resolve dependency : What to check, what to do ?

    - by fardon57
    Hi everyone, I'm using Ivy to resolve dependency in my very small project. It's the first time I'm doing that and it's more to learn as my project is very small. I had a problem 5 minutes ago, when trying to download log4j. My configuration is very basic, I have an ant task : <target name="resolve" description="--> retrieve dependencies with ivy"> <ivy:retrieve/> </target> and my Ivy.xml file is like this : <dependency org="javax.servlet" name="servlet-api" rev="2.5" /> <dependency org="log4j" name="log4j" rev="1.2.15" /> </dependencies> The problem is seems to happen when ivy tries to download jms 1.1 (I suppose it's needed for log4j) as I can see in the console : : ::::::::::::::::::::::::::::::::::::::::::::: [ivy:retrieve] :: FAILED DOWNLOADS :: [ivy:retrieve] :: ^ see resolution messages for details ^ :: [ivy:retrieve] :::::::::::::::::::::::::::::::::::::::::::::: [ivy:retrieve] :: javax.jms#jms;1.1!jms.jar [ivy:retrieve] :: com.sun.jdmk#jmxtools;1.2.1!jmxtools.jar [ivy:retrieve] :: com.sun.jmx#jmxri;1.2.1!jmxri.jar [ivy:retrieve] :::::::::::::::::::::::::::::::::::::::::::::: Is there anything I can do ? Thanks a lot guys. F

    Read the article

  • How to disable mod_security2 rule (false positive) for one domain on centos 5

    - by nicholas.alipaz
    Hi I have mod_security enabled on a centos5 server and one of the rules is keeping a user from posting some text on a form. The text is legitimate but it has the words 'create' and an html <table> tag later in it so it is causing a false positive. The error I am receiving is below: [Sun Apr 25 20:36:53 2010] [error] [client 76.171.171.xxx] ModSecurity: Access denied with code 500 (phase 2). Pattern match "((alter|create|drop)[[:space:]]+(column|database|procedure|table)|delete[[:space:]]+from|update.+set.+=)" at ARGS:body. [file "/usr/local/apache/conf/modsec2.user.conf"] [line "352"] [id "300015"] [rev "1"] [msg "Generic SQL injection protection"] [severity "CRITICAL"] [hostname "www.mysite.com"] [uri "/node/181/edit"] [unique_id "@TaVDEWnlusAABQv9@oAAAAD"] and here is /usr/local/apache/conf/modsec2.user.conf (line 352) #Generic SQL sigs SecRule ARGS "((alter|create|drop)[[:space:]]+(column|database|procedure|table)|delete[[:space:]]+from|update.+set.+=)" "id:1,rev:1,severity:2,msg:'Generic SQL injection protection'" The questions I have are: What should I do to "whitelist" or allow this rule to get through? What file do I create and where? How should I alter this rule? Can I set it to only be allowed for the one domain, since it is the only one having the issue on this dedicated server or is there a better way to exclude table tags perhaps? Thanks guys

    Read the article

  • Array Undefined index error (notice) in PHP

    - by Alex
    I have this function: function coin_matrix($test, $revs) { $coin = array(); for ($i = 0; $i < count($test); $i++) { foreach ($revs as $j => $rev) { foreach ($revs as $k => $rev) { if ($j != $k && $test[$i][$j] != null && $test[$i][$k] != null) { $coin[$test[$i][$j]][$test[$i][$k]] += 1 / ($some_var - 1); } } } } return $coin; } where $test = array( array('3'=>'1','5'=>'1'), array('3'=>'2','5'=>'2'), array('3'=>'1','5'=>'2'), array('3'=>'1','5'=>'1')); and $revs = array('3'=>'A','5'=>'B'); the problem is that when I run it, it returns these errors (notices): Notice: Undefined index: 1 at line 10 Notice: Undefined index: 1 at line 10 Notice: Undefined index: 2 at line 10 Notice: Undefined index: 2 at line 10 Notice: Undefined index: 2 at line 10 Notice: Undefined index: 1 at line 10 which is this line: $coin[$test[$i][$j]][$test[$i][$k]] += 1 / ($some_var - 1); Any suggestion is greatly appreciated! Thanks!

    Read the article

  • How can I unit test a PHP class method that executes a command-line program?

    - by acoulton
    For a PHP application I'm developing, I need to read the current git revision SHA which of course I can get easily by using shell_exec or backticks to execute the git command line client. I have obviously put this call into a method of its very own, so that I can easily isolate and mock this for the rest of my unit tests. So my class looks a bit like this: class Task_Bundle { public function execute() { // Do things $revision = $this->git_sha(); // Do more things } protected function git_sha() { return `git rev-parse --short HEAD`; } } Of course, although I can test most of the class by mocking git_sha, I'm struggling to see how to test the actual git_sha() method because I don't see a way to create a known state for it. I don't think there's any real value in a unit test that also calls git rev-parse to compare the results? I was wondering about at least asserting that the command had been run, but I can't see any way to get a history of shell commands executed by PHP - even if I specify that PHP should use BASH rather than SH the history list comes up empty, I presume because the separate backticks executions are separate terminal sessions. I'd love to hear any suggestions for how I might test this, or is it OK to just leave that method untested and be careful with it when the app is being maintained in future?

    Read the article

< Previous Page | 21 22 23 24 25 26 27 28 29 30 31 32  | Next Page >