Search Results

Search found 784 results on 32 pages for 'simplex noise'.

Page 25/32 | < Previous Page | 21 22 23 24 25 26 27 28 29 30 31 32  | Next Page >

• Coffee spilled and went inside CPU...computer not starting

  - by Harpreet

  Today coffee got spilled over my table, and some of it (very less) reached the CPU placed under the table. I think little bit of it got inside the CPU through the front face of the CPU. As that happened the fan started running very fast and made noise. I tried to restart to see if it becomes fine, but the computer didn't start again. First it gave an error of "Alert! Air temperature sensor not detected" and didn't start. Next I tried again multiple times of starting the computer but then it gave some memory error. I was not able to start the computer. Incase there's a problem in hard disk or something related to memory, is there any way we can extract our work or data? I am scared if I am not able to extract my work in case some problem occurs like that. What options would I have? Help! EDIT: I have attached the photo here and you can see the area spilt in red circle. The hard drive electronics have been affected and internal speaker may also have been affected. Any advise on cleaning and if hard drive can work? EDIT 2: Are there any professional services offered to extract data from blemished hard disk, like this one, in case I am not able to run it personally?

  Read the article

• Wireless to Wireless Transfer Slow on a Linksys WRT54GL

  - by Kyle Brandt

  The Situation: When I try to transfer a file from one computer to another that are both connected via wireless on a WRT54GL (in a office) with dd-wrt firmware I often get bad speeds. In generally they average around 100 kilobytes a second. Either computer can download via wireless from the Internet at at about 2 megabytes a second. The speed is slow with the transfer of one large file. There are about 20 other wireless networks that the computers can see, so there is a lot of noise, but I don't have the equipment to really monitor the frequencies well. But that still seems pretty slow. I thought maybe it was the transmit on each card, but even when they are 5 feet away with a line of sight I still get these speeds. According to Linux both cards are operating at 54g. My Questions: Is this normal for this sort of consumer level wireless equipment? Anything I can do to improve it? why is wireless to wireless transfer slow when everything else isn't? Whats steps might I take to figure out what is happening? For example, are lots of packets not making to the access point requiring retransmissions? Above all, I want to find out what the problem actually is. This may seem odd, but at this point I am more interested in understanding what the problem is than fixing it. What I have tried: I have tried messing with lots of settings. Different channels, xmit power, G-Only, none of which has made anything any better. I've also tried upgrading to newer dd-wrt firmware version and doing a reset to wipe out the settings.

  Read the article

• how i can identify which process is making UDP traffic on linux?

  - by boos

  my machine is continously making udp dns traffic request. what i need to know is the PID of the process generating this traffic. The normal way in TCP connection is to use netstat/lsof and get the process associated at the pid. Is UDP the connection is stateles, so, when i call netastat/lsof i can see it only if the UDP socket is opened and it's sending traffic. I have tried with lsof -i UDP and with nestat -anpue but i cant be able to find wich process is doing that request because i need to call lsof/netstat exactly when the udp traffic is sended, if i call lsof/netstat before/after the udp datagram is sended is impossible to view the opened UDP socket. call netstat/lsof exactly when 3/4 udp packet is sended is IMPOSSIBLE. how i can identify the infamous process ? I have already inspected the traffic to try to identify the sended PID from the content of the packet, but is not possible to identify it from the contect of the traffic. anyone can help me ? I'm root on this machine FEDORA 12 Linux noise.company.lan 2.6.32.16-141.fc12.x86_64 #1 SMP Wed Jul 7 04:49:59 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux

  Read the article

• Problems with Windows 7 restore

  - by Chris Lively

  My WD raptor 150 failed with a nice clicking noise. So, I picked up a velociraptor 300 and popped it in. I had windows set to do a full system backup nightly, so I figured the recovery ought to go easily. Well, it isn't. It is currently stuck on a screen that says: "Windows is restoring your computer from the system image. This might take from a few minutes to a few hours" Below that is a rather large progress meter with maybe the first block filled in. Below that is a message that says "Restoring disk (C:)..." It's been that way for over an hour. The first time around, I gave up after 2 hours. I then booted into the system recovery options and went to a command prompt and ran a chkdsk on the new drive. It showed several file inconsistencies and not much else. I ran a chkdsk /f on it and tried again... Which is where I'm at now. I can't see that the restore process should take this long before. Any ideas? UPDATE After 10 hours, it's still on "Restoring disk (C:)" and the progress meter is at roughly 5%. I'm guessing at the 5% as there isn't an actual number or anything else that I can look at showing what it's actually doing. The backup contains roughly 120GB of data. How slow is windows restore?

  Read the article

• How can I set the CD audio volume in Linux?

  - by user1296362

  In Windows 7 Control Panel - Sound - Sound Properties window there's an slider for setting CD Audio volume: And it's pretty strange that I can't find corresponding one in generic Linux mixers: alsamixer or amixer. I connected a CD drive to try to set CD audio volume with cdcd (CD Player): $ cdcd setvol 0 Invalid volume It isn't actually an invalid volume, it is because ioctl() call fails. I found that out after searching and changing a bit the source code of this utility (in the libcdaudio): --- cdaudio.c.orig 2004-09-09 06:26:20.000000000 +0600 +++ cdaudio.c 2012-05-30 21:34:34.167915521 +0600 @@ -578,8 +578,10 @@ cdvol_data.CDVOLCTRL_BACK_RIGHT_SELECT = CDAUDIO_MAX_VOLUME; #endif - if(ioctl(cd_desc, CDAUDIO_SET_VOLUME, &cdvol) < 0) - return -1; + if(ioctl(cd_desc, CDAUDIO_SET_VOLUME, &cdvol) < 0) { + printf("*** cd_set_volume: ioctl() returned error\n"); + return -1; + } return 0; } By the way cdcd's get volume command yields rather weird output: Left Right Front 1281734864 32767 Back 0 0 Also I tried aumix: $ aumix -c 0 But all with no success. I read from this manual — http://tldp.org/HOWTO/Alsa-sound-6.html (section 6.2 The mixer) that CD channel can present in amixer output. Maybe some drivers for sound card are missing in my Ubuntu 12.04 LTS installation. Though I don't think it's the case: $ lsmod | grep snd snd_mixer_oss 22602 0 snd_hda_codec_hdmi 32474 1 snd_hda_codec_realtek 223867 1 snd_hda_intel 33773 4 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 19 snd_mixer_oss,snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep ,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm All I need is just mute or set to 0 volume level of CD Audio channel, like I did in Windows 7, to get rid of sibilant noise in the speakers.

  Read the article

• How to discover true identity of hard disk?

  - by F21

  I have 2 fake external hard drives that claim to have a storage capacity of 2TB. I pulled the enclosure apart and the hard drives seems to be refurbished ones with their labels replaced as Barracuda LP 2000 GB labels (the serial numbers on both labels are the same). Interestingly, one of the drives have 160G written on it with pencil. However, the counterfeiters seem to have done something to the firmware, because CrystalDiskInfo reports them as 2TB ST2000DL003 drives. I then delete the 1.81 TB partition in Windows disk management and tried to create a new one and format it. Once I get to this point, the drives would make some noise that is common to dying drives. I am not interested in using these drives for production, but I am interested in finding the true identity (manufacturer/serial number/model number, etc) and restoring it to their factory defaults with the right capacity. Can this be done without any special equipment? This would be an interesting learning exercise. Some pictures of the drives in question: Here are the screens from CrystalDiskInfo: Note the serial numbers are the same (these are 2 different drives!). How is this done? Did they have to tamper with the controller board? I would assume that changing the firmware doesn't change the serial number at all.

  Read the article

• Coffee spilled inside computer, damaged hard drive

  - by Harpreet

  Today coffee spilled over my table, and some of it (very less) reached the PC case placed under the table. I think little bit of it got inside the PC case through the front. As that happened the fan started running very fast and made noise. I tried to restart to see if it becomes fine, but the computer didn't start again. First it gave an error of "Alert! Air temperature sensor not detected" and didn't start. Next I tried again multiple times of starting the computer but then it gave some memory error. I was not able to start the computer. Incase there's a problem in hard disk or something related to memory, is there any way we can extract our work or data? I am scared if I am not able to extract my work in case some problem occurs like that. What options would I have? Help!! EDIT: I have attached the photo here and you can see the area spilt in red circle. The hard drive electronics have been affected and internal speaker may also have been affected. Any advise on cleaning and if hard drive can work? EDIT 2: Are there any professional services offered to extract data from blemished hard disk, like this one, in case I am not able to run it personally?

  Read the article

• How to use WPA2 client mode in the Linux-based Cisco WAP4410N access point

  - by joechip

  I have a Cisco WAP4410N access point that I want to use as a client to connect to a WPA2 wireless network (for WLAN service monitoring purposes). Supposedly this access point supports a "Wireless Client/Repeater" mode that allows to do this. The Repeater function is optional (I have that box unchecked so that nobody can connect to this access point wirelessly). I have verified through SSH that the access point gets configured as a client and not as a Master. But it never associates to the SSID I ask it to. This is what iwconfig shows: ath04 IEEE 802.11ng ESSID:"myownssid" Mode:Managed Channel:0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:14 dBm Sensitivity=1/3 Retry:off RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=0/94 Signal level=161/162 Noise level=161/161 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Although I've never done this from the command line, I suppose I could use wpa_supplicant or wpa_client to associate it, but I don't know how to do that without editing configuration files and the filesystem is readonly. Besides, I would have to run those commands manually after every reboot. I'd like to know how to do this the Cisco way, if possible. If not, any trick to make this work would be useful. Edit: This is with the latest firmware, 2.0.4.2. And I found that not all of the filesystem is readonly, since /var and /tmp are mounted with type ramfs.

  Read the article

• What laptop would be recommended for video-editing or transcoding to blu-ray?

  - by Rob

  I'm looking for a machine (has to be a laptop) reasonably fast enough to handle editing/transcoding/rendering to Blu-ray disc of full true HD 1080p (1920x1080) video from a Samsung R10 camcorder - MPEG4 25fps (not the Sony-Panasonic AVCHD format): To be able to browse through the footage (say, quarter screen is fine for monitoring) and do simple edits - cut out bad bits, add titles, fades, nothing too fancy To be able to burn the footage in 1920x1080p 24p (twenty-four) fps to blu-ray, probably don't mind if I have to leave it for a few hours, or even overnight, as long as its not still running in the morning or takes days. I ALREADY have an external USB 2.0 LG BE06LU10 blu-ray burner. Does quad core make much difference? Or would Dual-core suffice for the above? NVidia because of CUDA for increased speed. What software today can take advantage of this? Which graphics card do I need? So far I've found Dell/Alienware to be well-specified, having a 5yr old Dell laptop that still runs well, albeit slow by today's standards, gives me a good impression. My concerns are too much fan-noise and budget and some Dell Precision Laptops exceed 1500 pounds. Thoughts?

  Read the article

• DV-AVI in DivX Plus Player and VirtualDub - playback issue

  - by user714965

  I have an AVI-video which I had (digitally) transferred from a DV camera to my PC. The video contains errors at the beginning most likely because the DV tape was pretty old. When playing this video in the DivX Plus Player I get some picture artefacts and some high noise peaks of the sound. These stops after two seconds. When I'm playing this video in VirtualDub (where I want to cut it) I get the same picture artefacts. But the sound errors (those loud high peaks) lasts ten seconds. These sound errors are also contained in the cutted video. Why does the video have more errors when played in VirtualDub? I think because of different codecs which are used for decoding the video? How can I change the codec which VirtualDub uses for decoding? I have installed ffdshow for this but it seems that it is not used because I don't get the ffdshow icon in the taskbar when playing the video in VirtualDub. When playing in DivX Player Plus I get this icon.

  Read the article

• Why Is Volume Shadow Copy Services stopping?

  - by David Mackintosh

  I am running Windows 7 Professional, 64-bit. I am running a backup-over-the-internet software client which depends on the Volume Shadow Copy Services running. Since I installed Service Pack 1 (or rather, didn't object when Windows Update forced Service Pack 1 on me) the backup service is failing to back everything up because VSC isn't running. Most of the time it fails to back up such noise as the Security Essentials database or the Messenger Live contact list -- stuff I really don't care about -- but I don't want to fall into the trap of accepting an Error-state backup as "normal". At the recommendation of the backup software, I have set the VSC service startup mode to be Automatic. When I look in the Event Log, System channel I can see at boot time: The Volume Shadow Copy service entered the running state. ...and then two or three minutes later: The Volume Shadow Copy service entered the stopped state. How do I figure out why VSC is stopping? At the suggestion of the backup vendor, I have already followed the suggestions from http://support.microsoft.com/default.aspx/kb/940184 net stop SENS net stop EventSystem net start EventSystem net start SENS net stop COMSysApp net stop SwPrv net stop VSS cd /d C:\Windows\system32 regsvr32 ole32.dll /s regsvr32 oleaut32.dll /s regsvr32 vss_ps.dll /s vssvc /register /s regsvr32 /i swprv.dll /s regsvr32 /i eventcls.dll /s regsvr32 es.dll /s regsvr32 stdprov.dll /s regsvr32 vssui.dll /s regsvr32 msxml.dll /s regsvr32 msxml3.dll /s regsvr32 msxml4.dll /s net start SwPrv net start VSS net start ProtectedStorage ...and per http://support.microsoft.com/kb/940184 I have deleted the key tree HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\EventSystem\{26c409cc-ae86-11d1-b616-00805fc79216}\Subscriptions I have also run chkdsk /F and chkdsk /R on both permanent hard disks. (I had a similar problem with another computer (same OS, same failure, same start point after SP1 install) but the problem went away when I forced Volume Shadow Copy Services to Automatic startup rather than Manual. I did not have to resort to following the Microsoft KB instructions.)

  Read the article

• Internet Troubles - PPPoE vs PPPoA?

  - by AkkA

  I have been having some internet troubles at home (ADSL2+ connection in Australia). We get random drop-outs from the authentication connection. It will keep the connection to the DSL service, but we lose authentication and either have to restart the router/modem (its combined, a Belkin one, not sure on model number) or unplug the phone cable, wait about 30 seconds and plug it in again. I've called the ISP (Telstra) a few times, but they only offer limited support when we dont use their supported hardware. Apparently something had happened on their side, they checked the box again (at least it sounded that simple), and told me it would be fine. It wasnt. I've replaced all the filters around the house, but that didnt help either. We do live a little bit away from the exchange (get a sync speed of about 3000/900), so I thought it could be due to line noise but that hasnt helped. Telstra allow both PPPoE and PPPoA connections (which I'm configuring through my router, dont have software on the PC side). I've been running PPPoA the whole time, would it make any difference changing it to PPPoE? If not, are there any other theories as to why we would be experiencing these drop-outs? It has been fine for at least 12 months, then suddenly started about 2 months ago.

  Read the article

• Getting rid of your server in a small business environment

  - by andygeers

  In a small business environment, is it still necessary to have a central server? Speaking for my own company (a small charity with about 12 employees) we use our server (Windows Server 2003) for the following: Email via Microsoft Exchange Central storage Acting as a print server User authentication / Active Directory There are significant costs associated with running a server like this: Electricity, first for the server itself then for the air conditioning required (this thing pumps out a lot of heat) Noise (of which there is a lot) IT support bills (both Windows Server and Exchange are pretty complicated, and there are many ways they can go wrong) I've found ways to replace many of these functions with cheaper (better?) alternatives: Google Apps / GMail is a clear win for us: we have so many spam related problems it's not even funny, and Outlook is dog slow on our aging computers You can buy networked storage devices with built in print servers, such as the Netgear ReadyNAS™ RND4210 that would allow us to store/share all of our documents, and allow us to access printers over the network The only thing that I can't figure out how to do away with is the authentication side of things - it seems to me that if we got rid of our server, you'd essentially have a bunch of independent PCs that had no shared pool of user accounts / no central administrator. Is that right? Does that matter? Am I missing any other good reasons to keep a central server? Does anybody know of any good, cost-effective ways of achieving the same end but without the expensive central server?

  Read the article

• Wireless does not work on Ubuntu 9.04

  - by Yongwei Xing

  Hi all I install the Ubuntu 9.04 my old Lenovo Y520 laptop, the wirless does not work.My Wireless card is Intel Pro/wireless 2100 card. But I can not enable it. My wired card is working well. Does anyone meet it before. the ifconfig output is eth0 Link encap:Ethernet HWaddr 00:0a:e4:5f:6c:30 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:973 errors:0 dropped:0 overruns:0 frame:0 TX packets:1025 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:574701 (574.7 KB) TX bytes:169249 (169.2 KB) Interrupt:10 eth1 Link encap:Ethernet HWaddr 00:0c:f1:58:79:b5 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:10 Base address:0x8000 Memory:d0202000-d0202fff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) the output of iwconfig is eth1 unassociated ESSID:off/any Nickname:"ipw2100" Mode:Managed Channel=0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:off Retry short limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I have another question. When my OS is 9.04, there is a icon about network connection on the panel at the top. After I upgraded to 9.10, that icon disappeared. How can I get that back? Best Regareds,

  Read the article

• This .mpg video clip doesn't play well

  - by Roey

  I've installed K-lite mega codec pack v6.9.0 with playback essentials without player. My default and only media player is windows media player. here are the clip's media info: General Complete name : D:\Users\Roey\Downloads\B384MV.mpg Format : MPEG-PS File size : 273 MiB Duration : 4mn 59s Overall bit rate : 7 643 Kbps Video ID : 224 (0xE0) Format : MPEG Video Format version : Version 2 Format profile : Main@High Format settings, BVOP : No Format settings, Matrix : Default Format settings, GOP : M=1, N=15 Duration : 4mn 57s Bit rate mode : Variable Bit rate : 7 363 Kbps Nominal bit rate : 9 000 Kbps Width : 1 920 pixels Height : 1 080 pixels Display aspect ratio : 16:9 Frame rate : 25.000 fps Color space : YUV Chroma subsampling : 4:2:0 Bit depth : 8 bits Scan type : Progressive Compression mode : Lossy Bits/(Pixel*Frame) : 0.142 Stream size : 261 MiB (96%) Audio ID : 192 (0xC0) Format : MPEG Audio Format version : Version 1 Format profile : Layer 3 Mode : Joint stereo Duration : 4mn 59s Bit rate mode : Constant Bit rate : 128 Kbps Channel(s) : 2 channels Sampling rate : 44.1 KHz Compression mode : Lossy Stream size : 4.56 MiB (2%) Menu When I play it there is no sound (just a little "kahhhh" noise every 10-20 seconds) and the frames are moving very slow - it "jumps" frames. A blue tray icon [FFa] "ffdshow audio decoder" pops with the following details: Input:MP3, stereo, 44100 Hz (libavocodec) Output:PCM, stereo, 44100 Hz, 16-bit integer Any help will be much appreciated. Thanks

  Read the article

• Should tripwire be entering /proc?

  - by dsadinoff

  When initializing the db with tripwire --init it spat out a bunch of errors pertaining to /proc: ### Warning: File system error. ### Filename: /proc/16982/fd/4 ### No such file or directory ### Continuing... ### Warning: File system error. ### Filename: /proc/16982/fdinfo/4 ### No such file or directory ### Continuing... ### Warning: File system error. ### Filename: /proc/16982/task/16982/fd/4 ### No such file or directory ### Continuing... ### Warning: File system error. ### Filename: /proc/16982/task/16982/fdinfo/4 ### No such file or directory ### Continuing... ### Warning: Duplicate object encountered. ### /proc/sys/net/ipv6/neigh This feels like noise. The twpol.txt file has the following clause: # # Critical devices # ( rulename = "Devices & Kernel information", severity = $(SIG_HI), ) { /dev -> $(Device) ; /proc -> $(Device) ; } Which, if I understand it right, is going to cause tripwire to care deeply about the entire contents of /proc. Shouldn't it just care about the static parts of /proc like the drivers and such, and not the per-pid stuff? Why does it ship like this?

  Read the article

• Connect to Nonencrypted Wireless Network Using Ubuntu Commands

  - by Tim

  I failed to connect to an open i.e. nonencrypted wireless network using Ubuntu command lines. Here is what I did: $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo /sbin/ifconfig wlan0 up $ sudo iwconfig wlan0 essid "Cavalier High-Speed 866-4-CAVTEL" $ sudo dhclient wlan0 There is already a pid file /var/run/dhclient.pid with pid 10812 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on Socket/fallback DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 21 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 6 No DHCPOFFERS received. Trying recorded lease 192.168.1.67 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms Trying recorded lease 192.168.1.45 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms No working leases in persistent database - sleeping. $ sudo /sbin/iwconfig wlan0 wlan0 IEEE 802.11bg Mode:Managed Frequency:2.422 GHz Access Point: Not-Associated Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Encryption key:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I was wondering what the problem is and how I can do it right? Thanks and regards!

  Read the article

• Erratic WiFi 2.4 GHz channel spikes, what gives?

  - by Francis W. Usher

  Sorry guys, first a gripe about my neighbor's WiFi access point (it is related): they totally hog the center nine 2.4 GHz channels (3-11), centered right at 7! I know the outer regions of the signal don't make as much of a difference, and technically they're running channels 5 & 9. Anyway, their signal is clearly interfering with mine, which is necessarily centered at 3 or 11 to evade their interference. I guess it's somewhat a case of access point envy: they happen to have both a stronger signal and a higher data rate, while occupying twice the band width that I do. Getting to the point, I've noticed that they tend to sit nice and pretty centered at 7, but they definitely auto-select their channel, and I've noticed that the auto-selection algorithm tends to shift towards the higher channels; hence I decided to pick channel 3, and I don't get so many intermittent lag spikes any more. Anyway, the thing that weirded me out was the reason they have to auto-select sometimes: unexplained, powerful (talking order of 0dB here), giant spikes of 2.4 GHz activity in consistent regions of the spectrum. I don't think it's just noise, since my wireless monitoring software is registering a MAC address, a manufacturer, and usually a fairly coherent ascii name... and it seems to be a fairly well-confined signal. But these signals are fairly common, and they do some weird stuff to my signal. So my question is what are these signals? Where are they coming from? Where are they going? Why are they so ridiculously strong? Why don't they ever last very long? Here's an inSSIDer screenshot I took, for your perusal. I am labeled with "me", my greedy neighbor labeled with "neighbor", and the 2 quasar signals are labeled with "WTF?".

  Read the article

• How to get data out of a Maxtor Shared Storage II that fails to boot?

  - by Jonik

  I've got a Maxtor Shared Storage II (RAID1 mode) which has developed some hardware failure, apparently: it fails to boot properly and is unreachable via network. When powering it on, it keeps making clunking/chirping disk noise and then sort of resets itself (with a flash of orange light in the usually-green LEDs); it then repeats this as if stuck in a loop. In fact, even the power button does nothing now – the only way I can affect the device at all is to plug in or pull out the power cord! (To be clear, I've come to regard this piece of garbage (which cost about 460 €) as my worst tech purchase ever. Even before this failure I had encountered many annoyances about the drive: 1) the software to manage it is rather crappy; 2) it is way noisier that what this type of device should be; 3) when your Mac comes out of sleep, Maxtor's "EasyManage" cannot re-mount the drive automatically.) Anyway, the question at hand is how to get my data out of it? As a very concrete first step, is there a way to open this thing without breaking the plastic casing into pieces? It is far from obvious to me how to get beyond this stage; it opens a little from one end but not from the other. If I somehow got the disks out, I could try mounting the disk(s) on one of the Macs or Linux boxes I have available (although I don't know yet if I'd need some adapters for that). (NB: for the purposes of this question, never mind any warranty or replacement issues – that's secondary to recovering the data.)

  Read the article

• ACER ASPIRE V3-571G-9435 Fan not kicking in leading to overclocking

  - by brythespy

  This laptop has always had this problem. The temperatures kick up to the thermal ceiling of 99C for the CPU (i7-3610QM) and 94C for the GPU (GT 640M). Problem is, the FAN doesn't give a damn. It's actually QUIETER when the temperatures are that high, than when it's at 60C or so. I figured it was a problem with the BIOS, so I updated that, no change. So maybe it was a problem with windows? Nope, same result on gaming with Ubuntu. The major problem of this, is that after gaming for ten minutes the CPU throttles itself to 1197MHz(as opposed to 3193), and the GPU goes down to 135MHz( as opposed to 843MHz). The problem is that the fan won't kick in like I know it can, because when the laptop is in POST, like at BIOS setup, the fan is like a vacuum cleaner it's so loud! I don't really care about noise, so I'd love to have the fan like that all the time as long as the temperatures don't fly through the roof... So, things I've tried so far, to avoid possible duplicate answers. Checked for dust: It's been this way since the laptop was new, and I've since then taken it apart. No dust buildup. Background stuff running?: No, problem persists across OS'es, and it happens while gaming anyways Manually underclocking both CPU/GPU: Using windows, I can force the CPU to stay at 1.1GHz, but the temperature STILL easily hits 99C after 5 min of gaming Contacted Acer support?: No help at all. They told me to update and reset the BIOS, which I have done multiple times. There are only about 6 changeable things anyway, none of which should affect the FAN control Third party fan control program?: None detect the fan So, I'm screwed until I can afford to replace this laptop, but I am very satisfied with performance in games... Whenever the CPU/GPU aren't being throttled. Anyone that can offer advice to solve this problem would be greatly appreciated. Hell, if you solved my problem I'd send you some monies through paypal.

  Read the article

• How can something relevant to graphics completely kill a motherboard?

  - by leladax

  I was coding something in OpenGL and after a bug there was an 'OS slowed down' situation. After a few seconds the screen went blank and the laptop shutdown. Now not even a led turns on battery or not. It doesn't appear to be the AC or the battery since there was some battery when it died and when it's connected to the AC the laptop produces near the AC connection a very slight 'clicking' noise (very faint, one has to be very careful to notice it, I don't know if it was there forever tbh). I suspect the motherboard died, as in something from the point it gets AC or battery power and the point it actually feeds itself. But I can't figure out how that effect was produced by the OpenGL bug or graphics overheating. If the graphics died alone, it should at least give some indication that the laptop is barely alive, at least a led, a sound, anything, the laptop is instead completely dead (other than faint 'clicking' I mentioned). Does anyone have expert advice on this? I'm especially interested in any ideas connected to "graphics overheated/bugged ---- they killed motherboard". I have a very lengthy experience in that stuff as a hobbyist and it really puzzles me. It's not just a "AC died" situation I can easily google.

  Read the article

• Internet Troubles - PPPoE vs PPPoA?

  - by AkkA

  I have been having some internet troubles at home (ADSL2+ connection in Australia). We get random drop-outs from the authentication connection. It will keep the connection to the DSL service, but we lose authentication and either have to restart the router/modem (its combined, a Belkin one, not sure on model number) or unplug the phone cable, wait about 30 seconds and plug it in again. I've called the ISP (Telstra) a few times, but they only offer limited support when we dont use their supported hardware. Apparently something had happened on their side, they checked the box again (at least it sounded that simple), and told me it would be fine. It wasnt. I've replaced all the filters around the house, but that didnt help either. We do live a little bit away from the exchange (get a sync speed of about 3000/900), so I thought it could be due to line noise but that hasnt helped. Telstra allow both PPPoE and PPPoA connections (which I'm configuring through my router, dont have software on the PC side). I've been running PPPoA the whole time, would it make any difference changing it to PPPoE? If not, are there any other theories as to why we would be experiencing these drop-outs? It has been fine for at least 12 months, then suddenly started about 2 months ago.

  Read the article

• Dual-head monitor system Kubuntu 10.04

  - by andrii

  I have a notebook Asus V6X00V with 1400*1050 monitor(name: LVDS) and Dell Monitor 1920*1080 (VGA-0). I want to have a dual monitor system. At MS Windows everything is working fine. During the Kubuntu installation the Dell and the main notebook monitors have a right resolutions(1920*1080 & 1400*1050). But after some stage it have been changed to the 1152*864 for both. Now the right resolution is only during turning off process and when I am using the console. So it shows that system can use this resolutions. The problem is just in a settings. I am using Size & Orientation - System Settings for setting adjustment. Any option that changes resolution for any monitor or changing position(Absolute, Left Of, Right of and so on) cause the color line noise on the screens. I have tried xrandr: xrandr --output LVDS --mode 1400x1050 --pos 0x0 --output VGA-0 --mode 1920x1080 --right-of LVDS --pos 1400x0 but have received the same result. I have find out that for example the previous version of Randr(1.2, now I have xrandr 1.3) need a xorg.conf file modification to create a big virtual screen, but kubuntu 10.4 don't have xorg.conf and I don't know should I modify xorg for 1.3 version of xrandr or not. Please help me to solve this problem

  Read the article

• Looking for a software / something to automate some simple audio processing

  - by Daniel Magliola

  I'm looking for a way to take a 1-hour podcast MP3 file and split it into several several 2-minute MP3s. Along the way, I'd like to also do a few things like Amplify the volume. The problem I'm solving is that I have a crappy MP3 player that won't let me seek forward or backward, nor will it remember where I left it when I turn it off, plus, I listen to these in a seriously high-noise situation. Thus, I need to be able to skip forward in large chunks (2-5 minutes) to the point where I left it. Is there any decent way to do this? Audacity doesn't seem to have command-line capabilities. I'm willing to write some code, for example, to call something over the command line and get how long the MP3 file is, to later know how many pieces i'll have, and then say "create an MP3 with 0:00 to 2:00", "create an MP3 with 2:00 to 4:00", etc. I'm also willing to pay for the right tools if necessary. I also don't care how slow this runs, as long as I can automate it :-) I'm doing this on Windows. Any pointers / ideas? Thanks!

  Read the article

• I think my laptop just died

  - by Joel Coehoorn

  I have a Dell 1330M that as of about 15 minutes ago will no longer POST. What happened was I was working, stepped away for a moment, and when I came back it was turned off. I thought that was odd, but turned it on and things seemed fine. About 1/2 hour later it crashed and restarted, but came up fine again. It did this once more. At this point I was starting to get worried, but I hadn't had any problems with the laptop before and every crash was after doing some work in a virtual machine that I don't often use, so I at put the blame there. It didn't feel like it was overheating anywhere and there's no ozone smell of overheated electronics. Then it crashed a final time and now when I turn it on all I see is a bright screen with a bunch of vertical lines (noise). I've tried removing the memory sticks one at a time, but I get the same result with either memory stick in either slot. With no memory at all it stops earlier in the POST process and the screen is completely blank (black, no backlight). As I type this, I hear a double beep from the system about once every 10 minutes. I'm pretty sure the hard drive is fine because it fails during post, before anything off the drive is needed. The power supply seems good because the screen is nice and bright. It's not the RAM because swapping that around made no difference. The leaves motherboard (which I doubt and can replace) and CPU (which just might be changable). Any ideas? Is there any hope for this laptop? I'm rather fond of it and I'd have a hard time replacing it with anything near as nice.

  Read the article

< Previous Page | 21 22 23 24 25 26 27 28 29 30 31 32  | Next Page >