Search Results

Search found 809 results on 33 pages for 'universal'.

Page 25/33 | < Previous Page | 21 22 23 24 25 26 27 28 29 30 31 32  | Next Page >

• PC doesn't POST with a certain model of PSU

  - by Core Xii

  I have this PC with an Asus P5N32-E SLI motherboard and an Intel Q6600 CPU. I got a new RX-5300 PSU, but it didn't work. The motherboard power LED is on fine When I switch power on, the PC powers up briefly (0.5-1 sec) then shuts down From there on out when I switch power on, it stays on, all fans and components seem to be receiving power, but the motherboard won't POST. No video output, no PC speaker beeps, nothing If I turn the hard switch on the PSU off and then back on again, go to step 2; The PC turns on and then off immediately again, and on subsequent power-ups it stays on but won't POST I disconnected every component but the motherboard, CPU and PSU. Still nothing. I tried three other models of PSU on this PC, both of higher (600) and lower (<300) wattage than the 530 on the RX-5300 and they all work fine. At this point I was convinced the PSU was faulty so I returned it. When the replacement arrived, it behaved exactly the same. So two different units of RX-5300 both with the same symptoms, neither working with this motherboard + CPU. Yet, three other models of PSU work perfectly fine. The PC store couldn't reproduce my problem with the returned PSU. I tried resetting the CMOS with the jumper. I tried with both the 4 and 4+4 (with and without the extra +4 connected) CPU connectors (curiously the RX-5300 comes equipped with both). Could it be a statistical probability that I get two units of the same model of PSU that are faulty in the exact same manner? Could the RX-5300 model itself be somehow incompatible with this motherboard? I was under the impression that PSUs were pretty much universal so long as you have the wattage. Could the motherboard be broken in some such a way as to work with certain PSUs but not others? What's going on here?

  Read the article

• Custom PCI bracket with support, for custom PCB?

  - by newbiez

  I am considering to put a custom PCB card that I made, into my computer. It won't go on any PCI connector, it plugs in on a USB connector on the motherboard, via a ribbon cable. I need thou to plug a device to it; which means that either I leave the PCB outside the case, hanging by the ribbon (bad idea), or I could put it in a PCI slot, using a bracket. The issue is that the brackets that I have, do not have tabs, so I have no way to screw the PCB on them. I was hoping to find something that would allow me to put the PCB on it, and then just fit it in the PCI bracket opening, like this: http://www.idotpc.com/TheStore/pc/viewPrd.asp?idproduct=1203&idcategory=0 This one won't fit the bill since the holes are too close apart, compared to the one that I have already on the PCB (and can't make more holes). Do you know if there is a place where they make universal PCI bracket mounting systems for custom PCB? I just need one, so can't even order a custom one (they ask me 120 dollars for one). Thanks in advance!

  Read the article

• RAIDs with a lot of spindles - how to safely put to use the "wasted" space

  - by kubanczyk

  I have a fairly large number of RAID arrays (server controllers as well as midrange SAN storage) that all suffer from the same problem: barely enough spindles to keep the peak I/O performance, and tons of unused disk space. I guess it's a universal issue since vendors offer the smallest drives of 300 GB capacity but the random I/O performance hasn't really grown much since the time when the smallest drives were 36 GB. One example is a database that has 300 GB and needs random performance of 3200 IOPS, so it gets 16 disks (4800 GB minus 300 GB and we have 4.5 TB wasted space). Another common example are redo logs for a OLTP database that is sensitive in terms of response time. The redo logs get their own 300 GB mirror, but take 30 GB: 270 GB wasted. What I would like to see is a systematic approach for both Linux and Windows environment. How to set up the space so sysadmin team would be reminded about the risk of hindering the performance of the main db/app? Or, even better, to be protected from that risk? The typical situation that comes to my mind is "oh, I have this very large zip file, where do I uncompress it? Umm let's see the df -h and we figure something out in no time..." I don't put emphasis on strictness of the security (sysadmins are trusted to act in good faith), but on overall simplicity of the approach. For Linux, it would be great to have a filesystem customized to cap I/O rate to a very low level - is this possible?

  Read the article

• Printer deployment via Group Policy not working on a single system

  - by Aron Rotteveel

  One of my coworkers just got a new laptop running Windows 7 Pro x64. We use a GPO to deploy the printers to every system, but for some reason it is not working on this system. I have been breaking my head over this for the past 3 hours now without any result. The strange thing is that gpresult /H seems to indicate that the GPO did run. The hardware: Laptop: Windows 7 Professional x64 Print server: Windows Server 2008 x64 R1 HP Color LaserJet 2605dn HP LaserJet P2015 Driver packages on server: HP universal printer driver PCL5, both X86 as X64 Oddities and other info: GPO working flawlessly on every other system, including my own Windows 7 Ultimate X64 laptop gpresult /H shows the GPO being ran Windows Firewall completely disabled on the new laptop Below is the output for gpresult /H (in Dutch sadly, but I think you'll recognize it): Beleidsregels Windows-instellingen Printerverbindingen Pad Dominerend groepsbeleidsobject \\Server2008\HP Color LaserJet 2605dn Printers \\Server2008\HP LaserJet P2015 Printers Beheersjablonen Beleidsdefinities (ADMX-bestanden) opgehaald van de lokale computer. Configuratiescherm/Printers Beleid Instelling Dominerend groepsbeleidsobject Beperkingen van point-and-print Uitgeschakeld Printers Like I said, I have been trying to figure this out for the past few hours or so without any result, so you are my last hope. Any help is appreciated.

  Read the article

• How to access files on a USB-connected NTFS disk removed from a Win7 notebook?

  - by yosh m

  My daughter seems to have fried her motherboard in her Lenovo Notebook. The disk seems to be fine. I removed the disk and used a universal disk-to-USB kit to attach it to another computer. The disk is recognized fine and I can peruse it in Windows Explorer. The problem is that the files she would like to recover from it are located in places that Windows refuses to let me access. When I try, for example, to enter the directory "Documents and Settings" it gives me an "Access is denied" error. Same thing when I try to go into the various User directories and other locations. I thought to try creating a Ghost image & retrieve the files from that, but Ghost seems to croak when I try to run it - apparently it doesn't like accessing the disk via a USB connection (even though I've told it to install the drivers for USB). Any other ideas about how to get to the files I need, either through Windows or perhaps some other OS that I could boot from a CD that can read an NTFS disk? Thanks, Yosh

  Read the article

• MAMP + Python MySQLDB - trouble installing

  - by Frederico

  I'm currently running the latest version of MAMP on my Snow Leopard OSX, and I'm trying to install MySQLDB. Downloaded: MySQL-python-1.2.3c1 I went into the setup_posix.py and adjusted the location of the mysql_config to the one in MAMP: mysql_config.path = "/Applications/MAMP/Library/bin/mysql_config" When trying to build I get the error below. Could anyone give me a hand please: creating build/temp.macosx-10.6-universal-2.6 gcc-4.2 -fno-strict-aliasing -fno-common -dynamic -DNDEBUG -g -fwrapv -Os -Wall -Wstrict-prototypes -DENABLE_DTRACE -arch i386 -arch ppc -arch x86_64 -pipe -Dversion_info=(1,2,3,'gamma',1) -D_version_=1.2.3c1 -I/Applications/MAMP/Library/include/mysql -I/System/Library/Frameworks/Python.framework/Versions/2.6/include/python2.6 -c _mysql.c -o build/temp.macosx-10.6-universal-2.6/_mysql.o -fno-omit-frame-pointer -D_P1003_1B_VISIBLE -DSIGNAL_WITH_VIO_CLOSE -DSIGNALS_DONT_BREAK_READ -DIGNORE_SIGHUP_SIGQUIT -DDONT_DECLARE_CXA_PURE_VIRTUAL _mysql.c:36:23: error: my_config.h: No such file or directory _mysql.c:38:19: error: mysql.h: No such file or directory _mysql.c:39:26: error: mysqld_error.h: No such file or directory _mysql.c:40:20: error: errmsg.h: No such file or directory _mysql.c:76: error: expected specifier-qualifier-list before ‘MYSQL’ _mysql.c:90: error: expected specifier-qualifier-list before ‘MYSQL_RES’ _mysql.c: In function ‘_mysql_Exception’: _mysql.c:120: warning: implicit declaration of function ‘mysql_errno’ _mysql.c:120: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:123: error: ‘CR_MAX_ERROR’ undeclared (first use in this function) _mysql.c:123: error: (Each undeclared identifier is reported only once _mysql.c:123: error: for each function it appears in.) _mysql.c:131: error: ‘CR_COMMANDS_OUT_OF_SYNC’ undeclared (first use in this function) _mysql.c:132: error: ‘ER_DB_CREATE_EXISTS’ undeclared (first use in this function) _mysql.c:133: error: ‘ER_SYNTAX_ERROR’ undeclared (first use in this function) _mysql.c:134: error: ‘ER_PARSE_ERROR’ undeclared (first use in this function) _mysql.c:135: error: ‘ER_NO_SUCH_TABLE’ undeclared (first use in this function) _mysql.c:136: error: ‘ER_WRONG_DB_NAME’ undeclared (first use in this function) _mysql.c:137: error: ‘ER_WRONG_TABLE_NAME’ undeclared (first use in this function) _mysql.c:138: error: ‘ER_FIELD_SPECIFIED_TWICE’ undeclared (first use in this function) _mysql.c:139: error: ‘ER_INVALID_GROUP_FUNC_USE’ undeclared (first use in this function) _mysql.c:140: error: ‘ER_UNSUPPORTED_EXTENSION’ undeclared (first use in this function) _mysql.c:141: error: ‘ER_TABLE_MUST_HAVE_COLUMNS’ undeclared (first use in this function) _mysql.c:170: error: ‘ER_DUP_ENTRY’ undeclared (first use in this function) _mysql.c:213: warning: implicit declaration of function ‘mysql_error’ _mysql.c:213: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:213: warning: passing argument 1 of ‘PyString_FromString’ makes pointer from integer without a cast _mysql.c: In function ‘_mysql_server_init’: _mysql.c:308: warning: label ‘finish’ defined but not used _mysql.c:234: warning: unused variable ‘item’ _mysql.c:233: warning: unused variable ‘groupc’ _mysql.c:233: warning: unused variable ‘i’ _mysql.c:233: warning: unused variable ‘cmd_argc’ _mysql.c:232: warning: unused variable ‘s’ _mysql.c: In function ‘_mysql_ResultObject_Initialize’: _mysql.c:363: error: ‘MYSQL_RES’ undeclared (first use in this function) _mysql.c:363: error: ‘result’ undeclared (first use in this function) _mysql.c:368: error: ‘MYSQL_FIELD’ undeclared (first use in this function) _mysql.c:368: error: ‘fields’ undeclared (first use in this function) _mysql.c:377: error: ‘_mysql_ResultObject’ has no member named ‘use’ _mysql.c:380: warning: implicit declaration of function ‘mysql_use_result’ _mysql.c:380: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:382: warning: implicit declaration of function ‘mysql_store_result’ _mysql.c:382: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:383: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c:386: error: ‘_mysql_ResultObject’ has no member named ‘converter’ _mysql.c:389: warning: implicit declaration of function ‘mysql_num_fields’ _mysql.c:390: error: ‘_mysql_ResultObject’ has no member named ‘nfields’ _mysql.c:391: error: ‘_mysql_ResultObject’ has no member named ‘converter’ _mysql.c:392: warning: implicit declaration of function ‘mysql_fetch_fields’ _mysql.c:438: error: ‘_mysql_ResultObject’ has no member named ‘converter’ _mysql.c: In function ‘_mysql_ResultObject_traverse’: _mysql.c:450: error: ‘_mysql_ResultObject’ has no member named ‘converter’ _mysql.c:451: error: ‘_mysql_ResultObject’ has no member named ‘converter’ _mysql.c: In function ‘_mysql_ResultObject_clear’: _mysql.c:462: error: ‘_mysql_ResultObject’ has no member named ‘converter’ _mysql.c:462: error: ‘_mysql_ResultObject’ has no member named ‘converter’ _mysql.c:462: error: ‘_mysql_ResultObject’ has no member named ‘converter’ _mysql.c:462: error: ‘_mysql_ResultObject’ has no member named ‘converter’ _mysql.c:463: error: ‘_mysql_ResultObject’ has no member named ‘converter’ _mysql.c: In function ‘_mysql_ConnectionObject_Initialize’: _mysql.c:475: error: ‘MYSQL’ undeclared (first use in this function) _mysql.c:475: error: ‘conn’ undeclared (first use in this function) _mysql.c:500: error: ‘_mysql_ConnectionObject’ has no member named ‘converter’ _mysql.c:501: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:525: error: ‘_mysql_ConnectionObject’ has no member named ‘converter’ _mysql.c:547: warning: implicit declaration of function ‘mysql_init’ _mysql.c:547: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:550: warning: implicit declaration of function ‘mysql_options’ _mysql.c:550: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:550: error: ‘MYSQL_OPT_CONNECT_TIMEOUT’ undeclared (first use in this function) _mysql.c:554: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:554: error: ‘MYSQL_OPT_COMPRESS’ undeclared (first use in this function) _mysql.c:555: error: ‘CLIENT_COMPRESS’ undeclared (first use in this function) _mysql.c:558: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:558: error: ‘MYSQL_OPT_NAMED_PIPE’ undeclared (first use in this function) _mysql.c:560: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:560: error: ‘MYSQL_INIT_COMMAND’ undeclared (first use in this function) _mysql.c:562: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:562: error: ‘MYSQL_READ_DEFAULT_FILE’ undeclared (first use in this function) _mysql.c:564: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:564: error: ‘MYSQL_READ_DEFAULT_GROUP’ undeclared (first use in this function) _mysql.c:567: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:567: error: ‘MYSQL_OPT_LOCAL_INFILE’ undeclared (first use in this function) _mysql.c:575: warning: implicit declaration of function ‘mysql_real_connect’ _mysql.c:575: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:590: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c: In function ‘_mysql_ConnectionObject_traverse’: _mysql.c:671: error: ‘_mysql_ConnectionObject’ has no member named ‘converter’ _mysql.c:672: error: ‘_mysql_ConnectionObject’ has no member named ‘converter’ _mysql.c: In function ‘_mysql_ConnectionObject_clear’: _mysql.c:680: error: ‘_mysql_ConnectionObject’ has no member named ‘converter’ _mysql.c:680: error: ‘_mysql_ConnectionObject’ has no member named ‘converter’ _mysql.c:680: error: ‘_mysql_ConnectionObject’ has no member named ‘converter’ _mysql.c:680: error: ‘_mysql_ConnectionObject’ has no member named ‘converter’ _mysql.c:681: error: ‘_mysql_ConnectionObject’ has no member named ‘converter’ _mysql.c: In function ‘_mysql_ConnectionObject_close’: _mysql.c:696: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:698: warning: implicit declaration of function ‘mysql_close’ _mysql.c:698: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:700: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c: In function ‘_mysql_ConnectionObject_affected_rows’: _mysql.c:722: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:723: warning: implicit declaration of function ‘mysql_affected_rows’ _mysql.c:723: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c: In function ‘_mysql_debug’: _mysql.c:739: warning: implicit declaration of function ‘mysql_debug’ _mysql.c: In function ‘_mysql_ConnectionObject_dump_debug_info’: _mysql.c:757: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:759: warning: implicit declaration of function ‘mysql_dump_debug_info’ _mysql.c:759: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c: In function ‘_mysql_ConnectionObject_autocommit’: _mysql.c:783: warning: implicit declaration of function ‘mysql_query’ _mysql.c:783: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c: In function ‘_mysql_ConnectionObject_commit’: _mysql.c:806: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c: In function ‘_mysql_ConnectionObject_rollback’: _mysql.c:828: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c: In function ‘_mysql_ConnectionObject_errno’: _mysql.c:940: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:941: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c: In function ‘_mysql_ConnectionObject_error’: _mysql.c:956: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:957: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:957: warning: passing argument 1 of ‘PyString_FromString’ makes pointer from integer without a cast _mysql.c: In function ‘_mysql_escape_string’: _mysql.c:981: warning: implicit declaration of function ‘mysql_escape_string’ _mysql.c: In function ‘_mysql_escape’: _mysql.c:1088: error: ‘_mysql_ConnectionObject’ has no member named ‘converter’ _mysql.c: In function ‘_mysql_ResultObject_describe’: _mysql.c:1168: error: ‘MYSQL_FIELD’ undeclared (first use in this function) _mysql.c:1168: error: ‘fields’ undeclared (first use in this function) _mysql.c:1171: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:1172: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c:1173: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c:1184: warning: implicit declaration of function ‘IS_NOT_NULL’ _mysql.c: In function ‘_mysql_ResultObject_field_flags’: _mysql.c:1204: error: ‘MYSQL_FIELD’ undeclared (first use in this function) _mysql.c:1204: error: ‘fields’ undeclared (first use in this function) _mysql.c:1207: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:1208: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c:1209: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c: At top level: _mysql.c:1250: error: expected declaration specifiers or ‘...’ before ‘MYSQL_ROW’ _mysql.c: In function ‘_mysql_row_to_tuple’: _mysql.c:1256: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c:1258: warning: implicit declaration of function ‘mysql_fetch_lengths’ _mysql.c:1258: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c:1258: warning: assignment makes pointer from integer without a cast _mysql.c:1261: error: ‘_mysql_ResultObject’ has no member named ‘converter’ _mysql.c:1262: error: ‘row’ undeclared (first use in this function) _mysql.c: At top level: _mysql.c:1275: error: expected declaration specifiers or ‘...’ before ‘MYSQL_ROW’ _mysql.c: In function ‘_mysql_row_to_dict’: _mysql.c:1280: error: ‘MYSQL_FIELD’ undeclared (first use in this function) _mysql.c:1280: error: ‘fields’ undeclared (first use in this function) _mysql.c:1282: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c:1284: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c:1284: warning: assignment makes pointer from integer without a cast _mysql.c:1285: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c:1288: error: ‘_mysql_ResultObject’ has no member named ‘converter’ _mysql.c:1289: error: ‘row’ undeclared (first use in this function) _mysql.c: At top level: _mysql.c:1314: error: expected declaration specifiers or ‘...’ before ‘MYSQL_ROW’ _mysql.c: In function ‘_mysql_row_to_dict_old’: _mysql.c:1319: error: ‘MYSQL_FIELD’ undeclared (first use in this function) _mysql.c:1319: error: ‘fields’ undeclared (first use in this function) _mysql.c:1321: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c:1323: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c:1323: warning: assignment makes pointer from integer without a cast _mysql.c:1324: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c:1327: error: ‘_mysql_ResultObject’ has no member named ‘converter’ _mysql.c:1328: error: ‘row’ undeclared (first use in this function) _mysql.c: At top level: _mysql.c:1350: error: expected declaration specifiers or ‘...’ before ‘MYSQL_ROW’ _mysql.c: In function ‘mysql_fetch_row’: _mysql.c:1361: error: ‘MYSQL_ROW’ undeclared (first use in this function) _mysql.c:1361: error: expected ‘;’ before ‘row’ _mysql.c:1365: error: ‘_mysql_ResultObject’ has no member named ‘use’ _mysql.c:1366: error: ‘row’ undeclared (first use in this function) _mysql.c:1366: warning: implicit declaration of function ‘mysql_fetch_row’ _mysql.c:1366: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c:1369: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c:1372: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:1380: error: too many arguments to function ‘convert_row’ _mysql.c: In function ‘_mysql_ResultObject_fetch_row’: _mysql.c:1404: error: expected declaration specifiers or ‘...’ before ‘MYSQL_ROW’ _mysql.c:1419: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:1431: error: ‘_mysql_ResultObject’ has no member named ‘use’ _mysql.c:1445: warning: implicit declaration of function ‘mysql_num_rows’ _mysql.c:1445: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c: In function ‘_mysql_ConnectionObject_character_set_name’: _mysql.c:1512: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c: In function ‘_mysql_get_client_info’: _mysql.c:1603: warning: implicit declaration of function ‘mysql_get_client_info’ _mysql.c:1603: warning: passing argument 1 of ‘PyString_FromString’ makes pointer from integer without a cast _mysql.c: In function ‘_mysql_ConnectionObject_get_host_info’: _mysql.c:1617: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:1618: warning: implicit declaration of function ‘mysql_get_host_info’ _mysql.c:1618: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:1618: warning: passing argument 1 of ‘PyString_FromString’ makes pointer from integer without a cast _mysql.c: In function ‘_mysql_ConnectionObject_get_proto_info’: _mysql.c:1632: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:1633: warning: implicit declaration of function ‘mysql_get_proto_info’ _mysql.c:1633: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c: In function ‘_mysql_ConnectionObject_get_server_info’: _mysql.c:1647: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:1648: warning: implicit declaration of function ‘mysql_get_server_info’ _mysql.c:1648: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:1648: warning: passing argument 1 of ‘PyString_FromString’ makes pointer from integer without a cast _mysql.c: In function ‘_mysql_ConnectionObject_info’: _mysql.c:1664: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:1665: warning: implicit declaration of function ‘mysql_info’ _mysql.c:1665: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:1665: warning: assignment makes pointer from integer without a cast _mysql.c: In function ‘_mysql_ConnectionObject_insert_id’: _mysql.c:1697: error: ‘my_ulonglong’ undeclared (first use in this function) _mysql.c:1697: error: expected ‘;’ before ‘r’ _mysql.c:1699: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:1701: error: ‘r’ undeclared (first use in this function) _mysql.c:1701: warning: implicit declaration of function ‘mysql_insert_id’ _mysql.c:1701: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c: In function ‘_mysql_ConnectionObject_kill’: _mysql.c:1718: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:1720: warning: implicit declaration of function ‘mysql_kill’ _mysql.c:1720: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c: In function ‘_mysql_ConnectionObject_field_count’: _mysql.c:1739: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:1741: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c: In function ‘_mysql_ResultObject_num_fields’: _mysql.c:1756: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:1757: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c: In function ‘_mysql_ResultObject_num_rows’: _mysql.c:1772: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:1773: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c: In function ‘_mysql_ConnectionObject_ping’: _mysql.c:1802: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:1803: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:1805: warning: implicit declaration of function ‘mysql_ping’ _mysql.c:1805: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c: In function ‘_mysql_ConnectionObject_query’: _mysql.c:1826: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:1828: warning: implicit declaration of function ‘mysql_real_query’ _mysql.c:1828: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c: In function ‘_mysql_ConnectionObject_select_db’: _mysql.c:1856: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:1858: warning: implicit declaration of function ‘mysql_select_db’ _mysql.c:1858: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c: In function ‘_mysql_ConnectionObject_shutdown’: _mysql.c:1877: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:1879: warning: implicit declaration of function ‘mysql_shutdown’ _mysql.c:1879: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c: In function ‘_mysql_ConnectionObject_stat’: _mysql.c:1904: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:1906: warning: implicit declaration of function ‘mysql_stat’ _mysql.c:1906: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:1906: warning: assignment makes pointer from integer without a cast _mysql.c: In function ‘_mysql_ConnectionObject_store_result’: _mysql.c:1927: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:1928: error: ‘_mysql_ConnectionObject’ has no member named ‘converter’ _mysql.c:1937: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c: In function ‘_mysql_ConnectionObject_thread_id’: _mysql.c:1966: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:1968: warning: implicit declaration of function ‘mysql_thread_id’ _mysql.c:1968: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c: In function ‘_mysql_ConnectionObject_use_result’: _mysql.c:1988: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:1989: error: ‘_mysql_ConnectionObject’ has no member named ‘converter’ _mysql.c:1998: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c: In function ‘_mysql_ConnectionObject_dealloc’: _mysql.c:2016: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c: In function ‘_mysql_ConnectionObject_repr’: _mysql.c:2028: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:2029: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c: In function ‘_mysql_ResultObject_data_seek’: _mysql.c:2047: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:2048: warning: implicit declaration of function ‘mysql_data_seek’ _mysql.c:2048: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c: In function ‘_mysql_ResultObject_row_seek’: _mysql.c:2061: error: ‘MYSQL_ROW_OFFSET’ undeclared (first use in this function) _mysql.c:2061: error: expected ‘;’ before ‘r’ _mysql.c:2063: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:2064: error: ‘_mysql_ResultObject’ has no member named ‘use’ _mysql.c:2069: error: ‘r’ undeclared (first use in this function) _mysql.c:2069: warning: implicit declaration of function ‘mysql_row_tell’ _mysql.c:2069: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c:2070: warning: implicit declaration of function ‘mysql_row_seek’ _mysql.c:2070: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c: In function ‘_mysql_ResultObject_row_tell’: _mysql.c:2082: error: ‘MYSQL_ROW_OFFSET’ undeclared (first use in this function) _mysql.c:2082: error: expected ‘;’ before ‘r’ _mysql.c:2084: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:2085: error: ‘_mysql_ResultObject’ has no member named ‘use’ _mysql.c:2090: error: ‘r’ undeclared (first use in this function) _mysql.c:2090: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c:2091: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c: In function ‘_mysql_ResultObject_dealloc’: _mysql.c:2099: warning: implicit declaration of function ‘mysql_free_result’ _mysql.c:2099: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c: At top level: _mysql.c:2330: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:2337: error: ‘_mysql_ConnectionObject’ has no member named ‘converter’ _mysql.c:2344: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:2351: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:2358: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:2421: error: ‘_mysql_ResultObject’ has no member named ‘converter’ _mysql.c:2421: error: initializer element is not constant _mysql.c:2421: error: (near initialization for ‘_mysql_ResultObject_memberlist[0].offset’) _mysql.c: In function ‘_mysql_ConnectionObject_getattr’: _mysql.c:2443: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:36:23: error: my_config.h: No such file or directory _mysql.c:38:19: error: mysql.h: No such file or directory _mysql.c:39:26: error: mysqld_error.h: No such file or directory _mysql.c:40:20: error: errmsg.h: No such file or directory _mysql.c:76: error: expected specifier-qualifier-list before ‘MYSQL’ _mysql.c:90: error: expected specifier-qualifier-list before ‘MYSQL_RES’ _mysql.c: In function ‘_mysql_Exception’: _mysql.c:120: warning: implicit declaration of function ‘mysql_errno’ _mysql.c:120: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:123: error: ‘CR_MAX_ERROR’ undeclared (first use in this function) _mysql.c:123: error: (Each undeclared identifier is reported only once _mysql.c:123: error: for each function it appears in.) _mysql.c:131: error: ‘CR_COMMANDS_OUT_OF_SYNC’ undeclared (first use in this function) _mysql.c:132: error: ‘ER_DB_CREATE_EXISTS’ undeclared (first use in this function) _mysql.c:133: error: ‘ER_SYNTAX_ERROR’ undeclared (first use in this function) _mysql.c:134: error: ‘ER_PARSE_ERROR’ undeclared (first use in this function) _mysql.c:135: error: ‘ER_NO_SUCH_TABLE’ undeclared (first use in this function) _mysql.c:136: error: ‘ER_WRONG_DB_NAME’ undeclared (first use in this function) _mysql.c:137: error: ‘ER_WRONG_TABLE_NAME’ undeclared (first use in this function) _mysql.c:138: error: ‘ER_FIELD_SPECIFIED_TWICE’ undeclared (first use in this function) _mysql.c:139: error: ‘ER_INVALID_GROUP_FUNC_USE’ undeclared (first use in this function) _mysql.c:140: error: ‘ER_UNSUPPORTED_EXTENSION’ undeclared (first use in this function) _mysql.c:141: error: ‘ER_TABLE_MUST_HAVE_COLUMNS’ undeclared (first use in this function) _mysql.c:170: error: ‘ER_DUP_ENTRY’ undeclared (first use in this function) _mysql.c:213: warning: implicit declaration of function ‘mysql_error’ _mysql.c:213: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:213: warning: passing argument 1 of ‘PyString_FromString’ makes pointer from integer without a cast _mysql.c: In function ‘_mysql_server_init’: _mysql.c:308: warning: label ‘finish’ defined but not used _mysql.c:234: warning: unused variable ‘item’ _mysql.c:233: warning: unused variable ‘groupc’ _mysql.c:233: warning: unused variable ‘i’ _mysql.c:233: warning: unused variable ‘cmd_argc’ _mysql.c:232: warning: unused variable ‘s’ _mysql.c: In function ‘_mysql_ResultObject_Initialize’: _mysql.c:363: error: ‘MYSQL_RES’ undeclared (first use in this function) _mysql.c:363: error: ‘result’ undeclared (first use in this function) _mysql.c:368: error: ‘MYSQL_FIELD’ undeclared (first use in this function) _mysql.c:368: error: ‘fields’ undeclared (first use in this function) _mysql.c:377: error: ‘_mysql_ResultObject’ has no member named ‘use’ _mysql.c:380: warning: implicit declaration of function ‘mysql_use_result’ _mysql.c:380: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:382: warning: implicit declaration of function ‘mysql_store_result’ _mysql.c:382: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:383: error: ‘_mysql_ResultObject’ has no member named ‘result’ _mysql.c:386: error: ‘_mysql_ResultObject’ has no member named ‘converter’ _mysql.c:389: warning: implicit declaration of function ‘mysql_num_fields’ _mysql.c:390: error: ‘_mysql_ResultObject’ has no member named ‘nfields’ _mysql.c:391: error: ‘_mysql_ResultObject’ has no member named ‘converter’ _mysql.c:392: warning: implicit declaration of function ‘mysql_fetch_fields’ _mysql.c:438: error: ‘_mysql_ResultObject’ has no member named ‘converter’ _mysql.c: In function ‘_mysql_ResultObject_traverse’: _mysql.c:450: error: ‘_mysql_ResultObject’ has no member named ‘converter’ _mysql.c:451: error: ‘_mysql_ResultObject’ has no member named ‘converter’ _mysql.c: In function ‘_mysql_ResultObject_clear’: _mysql.c:462: error: ‘_mysql_ResultObject’ has no member named ‘converter’ _mysql.c:462: error: ‘_mysql_ResultObject’ has no member named ‘converter’ _mysql.c:462: error: ‘_mysql_ResultObject’ has no member named ‘converter’ _mysql.c:462: error: ‘_mysql_ResultObject’ has no member named ‘converter’ _mysql.c:463: error: ‘_mysql_ResultObject’ has no member named ‘converter’ _mysql.c: In function ‘_mysql_ConnectionObject_Initialize’: _mysql.c:475: error: ‘MYSQL’ undeclared (first use in this function) _mysql.c:475: error: ‘conn’ undeclared (first use in this function) _mysql.c:500: error: ‘_mysql_ConnectionObject’ has no member named ‘converter’ _mysql.c:501: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c:525: error: ‘_mysql_ConnectionObject’ has no member named ‘converter’ _mysql.c:547: warning: implicit declaration of function ‘mysql_init’ _mysql.c:547: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:550: warning: implicit declaration of function ‘mysql_options’ _mysql.c:550: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:550: error: ‘MYSQL_OPT_CONNECT_TIMEOUT’ undeclared (first use in this function) _mysql.c:554: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:554: error: ‘MYSQL_OPT_COMPRESS’ undeclared (first use in this function) _mysql.c:555: error: ‘CLIENT_COMPRESS’ undeclared (first use in this function) _mysql.c:558: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:558: error: ‘MYSQL_OPT_NAMED_PIPE’ undeclared (first use in this function) _mysql.c:560: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:560: error: ‘MYSQL_INIT_COMMAND’ undeclared (first use in this function) _mysql.c:562: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:562: error: ‘MYSQL_READ_DEFAULT_FILE’ undeclared (first use in this function) _mysql.c:564: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:564: error: ‘MYSQL_READ_DEFAULT_GROUP’ undeclared (first use in this function) _mysql.c:567: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:567: error: ‘MYSQL_OPT_LOCAL_INFILE’ undeclared (first use in this function) _mysql.c:575: warning: implicit declaration of function ‘mysql_real_connect’ _mysql.c:575: error: ‘_mysql_ConnectionObject’ has no member named ‘connection’ _mysql.c:590: error: ‘_mysql_ConnectionObject’ has no member named ‘open’ _mysql.c: In function ‘_mysql_ConnectionObject_traverse’: _mysql.c:671: error: ‘_mysql_ConnectionObject’ has no member named ‘converter’ _mysql.c:

  Read the article

• How does one get UI_USER_INTERFACE_IDIOM() to work with iPhone OS SDK < 3.2

  - by drootang

  Apple advises using the following code to detect whether running on an iPad or iPhone/iPod Touch: if (UI_USER_INTERFACE_IDIOM() == UIUserInterfaceIdiomPad) { // The device is an iPad running iPhone 3.2 or later. // [for example, load appropriate iPad nib file] } else { // The device is an iPhone or iPod touch. // [for example, load appropriate iPhone nib file] } The problem is that UI_USER_INTERFACE_IDIOM() and UIUserInterfaceIdiomPad are NOT defined in the SDKs priory to 3.2. This seems to completely defeat the purpose of such a function. They can only be compiled and run on iPhone OS 3.2 (iPhone OS 3.2 can only be run on iPad). So if you can use UI_USER_INTERFACE_IDIOM(), the result will always be to indicate an iPad. If you include this code and target OS 3.1.3 (the most recent iPhone/iPod Touch OS) in order to test your iPhone-bound universal app code, you will get compiler errors since the symbols are not defined in 3.1.3 or earlier. If this is the recommended-by-Apple approach to runtime device-detection, what am I doing wrong? Has anyone succeeded using this approach to device-detection?

  Read the article

• UI_USER_INTERFACE_IDIOM() does not work with iPhone OS SDK < 3.2

  - by drootang

  Apple advises using the following code to detect whether running on an iPad or iPhone/iPod Touch: if (UI_USER_INTERFACE_IDIOM() == UIUserInterfaceIdiomPad) { // The device is an iPad running iPhone 3.2 or later. // [for example, load appropriate iPad nib file] } else { // The device is an iPhone or iPod touch. // [for example, load appropriate iPhone nib file] } The problem is that UI_USER_INTERFACE_IDIOM() and UIUserInterfaceIdiomPad are NOT defined in the SDKs priory to 3.2. This seems to completely defeat the purpose of such a function. They can only be compiled and run on iPhone OS 3.2 (iPhone OS 3.2 can only be run on iPad). So if you can use UI_USER_INTERFACE_IDIOM(), the result will always be to indicate an iPad. If you include this code and target OS 3.1.3 (the most recent iPhone/iPod Touch OS) in order to test your iPhone-bound universal app code, you will get compiler errors since the symbols are not defined in 3.1.3 or earlier. If this is the recommended-by-Apple approach to runtime device-detection, what am I doing wrong? Has anyone succeeded using this approach to device-detection?

  Read the article

• How to speed up WPF programs?

  - by Sam

  I love programming with and for Windows Presentation Framework. Mostly I write browser-like apps using WPF and XAML. But what really annoys me is the slowness of WPF. A simple page with only a few controls loads fast enough, but as soon as a page is a teeny weeny bit more complex, like containing a lot of data entry fields, one or two tab controls, and stuff, it gets painful. Loading of such a page can take more than one second. Seconds, indeed, especially on not so fast computers (read: the customers computers) it can take ages. Same with changing values on the page. Everything about the WPF UI is somehow sluggy. This is so mean! They give me this beautiful framework, but make it so excruciatingly slow so I'll have to apologize to our customers all the time! My Question: How do you speed up WPF? How do you profile bottlenecks? How do you deal with the slowness? Since this seems to be an universal problem with WPF, I'm looking for general advice, useful for many situations and problems. Some other related questions: What tools do you use for WPF development Tools to develop WPF or Silverlight applications

  Read the article

• Using events in an external swf to load a new external swf

  - by wdense51

  Hi I'm trying to get an external swf to load when the flv content of another external swf finishes playing. I've only been using actiosncript 3 for about a week and I've got to this point from tutorials, so my knowledge is limited. This is what I've got so far: Code for External swf (with flv content): import fl.video.FLVPlayback; import fl.video.VideoEvent; motionClip.playPauseButton = player; motionClip.seekBar = seeker; motionClip.addEventListener(VideoEvent.COMPLETE, goNext); function goNext(e:VideoEvent):void { nextFrame(); } And this is the code for the main file: var Xpos:Number=110; var Ypos:Number=110; var swf_MC:MovieClip = new MovieClip(); var loader:Loader = new Loader(); var defaultSWF:URLRequest = new URLRequest("arch_reel.swf"); addChild (swf_MC); swf_MC.x=Xpos swf_MC.y=Ypos loader.load(defaultSWF); swf_MC.addChild(loader); //Btns Universal Function function btnClick(event:MouseEvent):void{ SoundMixer.stopAll(); swf_MC.removeChild(loader); var newSWFRequest:URLRequest = new URLRequest("motion.swf"); loader.load(newSWFRequest); swf_MC.addChild(loader); } function returnSWF(event:Event):void{ swf_MC.removeChild(loader); loader.load(defaultSWF); swf_MC.addChild(loader); } //Btn Listeners motion.addEventListener(MouseEvent.CLICK,btnClick); swf_MC.addEventListener(swf_MC.motionClip.Event.COMPLETE,swf_MC.motionClip.eventClip, returnSWF); I'm starting to get an understanding of how all of this works, but it's all to new to me at the moment, so I'm sure I've approached it from the wrong angle. Any help would be fantastic, as I've been trying at this for a few days now. Thanks

  Read the article

• What is the worst programming language you ever worked with? [closed]

  - by Ludwig Weinzierl

  If you have an interesting story to share, please post an answer, but do not abuse this question for bashing a language. We are programmers, and our primary tool is the programming language we use. While there is a lot of discussion about the best one, I'd like to hear your stories about the worst programming languages you ever worked with and I'd like to know exactly what annoyed you. I'd like to collect this stories partly to avoid common pitfalls while designing a language (especially a DSL) and partly to avoid quirky languages in the future in general. This question is not subjective. If a language supports only single character identifiers (see my own answer) this is bad in a non-debatable way. EDIT Some people have raised concerns that this question attracts trolls. Wading through all your answers made one thing clear. The large majority of answers is appropriate, useful and well written. UPDATE 2009-07-01 19:15 GMT The language overview is now complete, covering 103 different languages from 102 answers. I decided to be lax about what counts as a programming language and included anything reasonable. Thank you David for your comments on this. Here are all programming languages covered so far (alphabetical order, linked with answer, new entries in bold): ABAP, all 20th century languages, all drag and drop languages, all proprietary languages, APF, APL (1), AS400, Authorware, Autohotkey, BancaStar, BASIC, Bourne Shell, Brainfuck, C++, Centura Team Developer, Cobol (1), Cold Fusion, Coldfusion, CRM114, Crystal Syntax, CSS, Dataflex 2.3, DB/c DX, dbase II, DCL, Delphi IDE, Doors DXL, DOS batch (1), Excel Macro language, FileMaker, FOCUS, Forth, FORTRAN, FORTRAN 77, HTML, Illustra web blade, Informix 4th Generation Language, Informix Universal Server web blade, INTERCAL, Java, JavaScript (1), JCL (1), karol, LabTalk, Labview, Lingo, LISP, Logo, LOLCODE, LotusScript, m4, Magic II, Makefiles, MapBasic, MaxScript, Meditech Magic, MEL, mIRC Script, MS Access, MUMPS, Oberon, object extensions to C, Objective-C, OPS5, Oz, Perl (1), PHP, PL/SQL, PowerDynamo, PROGRESS 4GL, prova, PS-FOCUS, Python, Regular Expressions, RPG, RPG II, Scheme, ScriptMaker, sendmail.conf, Smalltalk, Smalltalk , SNOBOL, SpeedScript, Sybase PowerBuilder, Symbian C++, System RPL, TCL, TECO, The Visual Software Environment, Tiny praat, TransCAD, troff, uBasic, VB6 (1), VBScript (1), VDF4, Vimscript, Visual Basic (1), Visual C++, Visual Foxpro, VSE, Webspeed, XSLT The answers covering 80386 assembler, VB6 and VBScript have been removed.

  Read the article

• iPad app crashes when Youtube player clicked in UIWebView

  - by choonkeat

  I have a iPhone/iPad app (universal binary) with a regular UIWebView that displays webpages on the Internet. When the user presses on a Youtube embed, the iPhone app performs normally -- opening up the video player, when you close it, it returns to the app. However, on the iPad it crashes with Terminating app due to uncaught exception 'NSInvalidArgumentException', reason: '*** -[UIWindow addEventMonitor:]: unrecognized selector sent to instance 0x1219c0' #0 0x30c8e0a0 in __kill () #1 0x30c8e096 in kill () #2 0x30c8e088 in raise () #3 0x30ca2210 in abort () #4 0x32944a22 in __gnu_cxx::__verbose_terminate_handler () #5 0x335657ca in _objc_terminate () #6 0x32942df4 in __cxxabiv1::__terminate () #7 0x32942e48 in std::terminate () #8 0x32942f18 in __cxa_throw () #9 0x335646aa in objc_exception_throw () #10 0x32c9517a in -[NSObject doesNotRecognizeSelector:] () #11 0x32c94b00 in ___forwarding___ () #12 0x32c316d0 in __forwarding_prep_0___ () #13 0x32810492 in -[MPInactivityMonitor initForWindow:inactivityDuration:delegate:] () #14 0x32831dfe in -[MPFullScreenVideoViewController _createInactivityMonitor] () #15 0x328324bc in -[MPFullScreenVideoViewController showOverlayAnimated:] () #16 0x32833612 in -[MPAbstractFullScreenVideoViewController setControlsOverlayVisible:animate:] () #17 0x3281fca4 in -[UIMoviePlayerController setControlsOverlayVisible:disableAutohide:animate:] () #18 0x330bb444 in -[YTMovieView _switchToVideo:] () #19 0x330bb028 in -[YTMovieView willShowForVideo:inList:orVideoID:] () #20 0x04b8d142 in dyld_stub_time () #21 0x04b8b82e in dyld_stub_time () #22 0x32c2616c in -[NSObject performSelector:withObject:withObject:] () #23 0x3152716c in -[UIApplication sendAction:to:from:forEvent:] () #24 0x3152710c in -[UIApplication sendAction:toTarget:fromSender:forEvent:] () #25 0x315270de in -[UIControl sendAction:to:forEvent:] () #26 0x31526e30 in -[UIControl(Internal) _sendActionsForEvents:withEvent:] () #27 0x3152747e in -[UIControl touchesEnded:withEvent:] () #28 0x31525e54 in -[UIWindow _sendTouchesForEvent:] () #29 0x3152579c in -[UIWindow sendEvent:] () #30 0x315213be in -[UIApplication sendEvent:] () #31 0x31520d2a in _UIApplicationHandleEvent () #32 0x30d62b32 in PurpleEventCallback () #33 0x32c23d9c in CFRunLoopRunSpecific () #34 0x32c234e0 in CFRunLoopRunInMode () #35 0x30d620da in GSEventRunModal () #36 0x30d62186 in GSEventRun () #37 0x314d54c8 in -[UIApplication _run] () #38 0x314d39f2 in UIApplicationMain () (I don't even see my app in the stack trace (except for the top level main.m) In iPad Mobile Safari, on the same webpage, the video will play in-place on the webpage. Is there anything I have to do to enable that? Or did I forget to enable something?

  Read the article

• Uploadify: Passing a form's ID as a parameter with scriptData

  - by Matt

  I need the ability to have multiple upload inputs on one page (potentially hundreds) using Uploadify. The upload PHP file will be renaming the uploaded file based on the ID of the input button used to submit it, so it will need that ID. Since I will be having hundreds of upload buttons on one page, I wanted to create a universal instantiation, so I did this using the class of the forms rather than the ID of the forms. However, when one of the inputs is clicked, I would like to pass the ID of that input as scriptData to the PHP. This is not working; PHP says 'formId' is undefined. Is there a good way get the ID attribute of the form input being used, and passing it to the upload PHP? Or is there a completely different and better method of accomplishing this? Thank you in advance!! <script type="text/javascript"> $(document).ready(function() { $('.uploady').uploadify({ 'uploader' : '/uploadify/uploadify.swf', 'script' : '/uploadify/uploadify.php', 'cancelImg' : '/uploadify/cancel.png', 'folder' : '/uploadify', 'auto' : true, // LINE IN QUESTION 'scriptData' : {'formId':$(this).attr('id')} }); }); </script> </head> The inputs look like this: <input id="file_upload1" class="uploady" name="file_upload" type="file" /> <input id="file_upload2" class="uploady" name="file_upload" type="file" /> <input id="file_upload3" class="uploady" name="file_upload" type="file" />

  Read the article

• shouldAutorotateToInterfaceOrientation won't work!

  - by Dror Sabbag

  Hey. I've been writing my Universal application in portrait mode, and now after about 15 nib files, many many viewCotnrollers, i'd like to implement the shouldAutorotateToInterfaceOrientation and desing some screens in Landscape mode. adding : - (BOOL)shouldAutorotateToInterfaceOrientation:(UIInterfaceOrientation)interfaceOrientation { return YES; } to ALL of my viewControllers, does not do the work. During Debug, i see that this method is called, but it just won't work! not in the simulator, not in the device, not in Iphone, not in Ipad! i've searched some answers in the forum, and saw some advises to use: - (BOOL)shouldAutorotateToInterfaceOrientation:(UIInterfaceOrientation)interfaceOrientation { return (interfaceOrientation == UIInterfaceOrientationPortrait || interfaceOrientation == UIInterfaceOrientationLandscapeLeft || interfaceOrientation == UIInterfaceOrientationLandscapeRight || interfaceOrientation == UIInterfaceOrientationPortraitUpsideDown ); } Didn't worked either, adding: [[UIDevice currentDevice] beginGeneratingDeviceOrientationNotifications]; and [[UIDevice currentDevice] endGeneratingDeviceOrientationNotifications]; to my viewDidLoad and viewDidUnload respectively didn't worked either. I'm lost.. Any help will do! just one more info... all my Views are of type UIControl, as i needed the TuchUpInside to work. Appriciate your help.

  Read the article

• Could CouchDB benefit significantly from the use of BERT instead of JSON?

  - by Victor Rodrigues

  I appreciate a lot CouchDB attempt to use universal web formats in everything it does: RESTFUL HTTP methods in every interaction, JSON objects, javascript code to customize database and documents. CouchDB seems to scale pretty well, but the individual cost to make a request usually makes 'relational' people afraid of. Many small business applications should deal with only one machine and that's all. In this case the scalability talk doesn't say too much, we need more performance per request, or people will not use it. BERT (Binary ERlang Term http://bert-rpc.org/ ) has proven to be a faster and lighter format than JSON and it is native for Erlang, the language in which CouchDB is written. Could we benefit from that, using BERT documents instead of JSON ones? I'm not saying just for retrieving in views, but for everything CouchDB does, including syncing. And, as a consequence of it, use Erlang functions instead of javascript ones. This would modify some original CouchDB principles, because today it is very web oriented. Considering I imagine few people would make their database API public and usually its data is accessed by the users through an application, it would be a good deal to have the ability to configure CouchDB for working faster. HTTP+JSON calls could still be handled by CouchDB, considering an extra cost in these cases because of parsing.

  Read the article

• How to resolve deprecation warnings for OpenSSL::Cipher::Cipher#encrypt

  - by Olly

  I've just upgraded my Mac to Snow Leopard and got my Rails environment up and running. The only difference -- OSX aside -- with my previous install is that I'm now running ruby 1.8.7 (2008-08-11 patchlevel 72) [universal-darwin10.0] (Snow Leopard default) rather than 1.8.6. I'm now seeing deprecation warnings relating to OpenSSL when I run my code: warning: argumtents for OpenSSL::Cipher::Cipher#encrypt and OpenSSL::Cipher::Cipher#decrypt were deprecated; use OpenSSL::Cipher::Cipher#pkcs5_keyivgen to derive key and IV Example of my code which is causing these warnings (it decodes an encrypted string) on line 4: 1. def decrypt(data) 2. encryptor = OpenSSL::Cipher::Cipher.new('DES-EDE3-CBC') 3. key = "my key" 4. encryptor.decrypt(key) 5. text = encryptor.update(data) 6. text << encryptor.final 7. end I'm struggling to understand how I can resolve this, and Google isn't really helping. Should I try and downgrade to Ruby 1.8.6 (and if so, what's the best way of doing this?), should I try and just hide the warnings (bury my head in the sand?!) or is there an easy fix I can apply in the code?

  Read the article

• How do I debug a crash when I run my garbage-collected app in Rosetta?

  - by Rob Keniger

  I have a Universal app which is targeting 10.5 and which uses garbage collection. I am building for ppc, i386 and x86_64. I don't have access to a physical PowerPC machine so I am trying to use Rosetta to confirm that the PowerPC portion of the app works correctly. However, as soon as the app is launched in Rosetta it immediately crashes with the following crash log: Process: FooApp [91567] Path: /Users/rob/Development/src/FooApp/build/Release 64-bit/FooApp.app/Contents/MacOS/FooApp Identifier: com.companyX.FooApp Version: 0.9 (build d540e05) (2) Code Type: PPC (Translated) Parent Process: launchd [708] Date/Time: 2010-04-09 18:32:23.962 +1000 OS Version: Mac OS X 10.6.3 (10D573) Report Version: 6 Exception Type: EXC_CRASH (SIGTRAP) Exception Codes: 0x0000000000000000, 0x0000000000000000 Crashed Thread: 5 ...snip non-relevant threads... Thread 5 Crashed: 0 libSystem.B.dylib 0x8023656a __pthread_kill + 10 1 libSystem.B.dylib 0x80235e17 pthread_kill + 95 2 com.companyX.FooApp 0xb80bfb30 0xb8000000 + 785200 3 com.companyX.FooApp 0xb80c0037 0xb8000000 + 786487 4 com.companyX.FooApp 0xb80dd8e8 0xb8000000 + 907496 5 com.companyX.FooApp 0xb8145397 spin_lock_wrapper + 1791 6 com.companyX.FooApp 0xb801ceb7 0xb8000000 + 118455 I have used the Apple docs on debugging translated apps and the information on this page to attach gdb to the app when it's running in Rosetta. The app immediately breaks into the debugger upon launch: Program received signal SIGTRAP, Trace/breakpoint trap. [Switching to thread 15107] 0x9151fdd4 in auto_fatal () (gdb) bt #0 0x9151fdd4 in auto_fatal () #1 0x91536d84 in Auto::Thread::get_register_state () #2 0x915372f8 in Auto::Thread::scan_other_thread () #3 0x91529be4 in Auto::Zone::scan_registered_threads () #4 0x91539114 in Auto::MemoryScanner::scan_thread_ranges () #5 0x9153b000 in Auto::MemoryScanner::scan () #6 0x9153049c in Auto::Zone::collect () #7 0x915198f4 in auto_collect_internal () #8 0x9151a094 in auto_collection_work () #9 0x96687434 in _dispatch_call_block_and_release () #10 0x9668912c in _dispatch_queue_drain () #11 0x96689350 in _dispatch_queue_invoke () #12 0x966895c0 in _dispatch_worker_thread2 () #13 0x966896fc in _dispatch_worker_thread () #14 0x965a97e8 in _pthread_body () (gdb) I have no idea where to start with this. It looks like the Garbage Collector is failing very badly. Are garbage-collected PowerPC apps not supported in Rosetta? I can't see any mention of this limitation in the docs if so. Does anyone have any ideas?

  Read the article

• iPad: Displaying UIActionSheet with UIPickerView as subview

  - by E-Madd

  I'm in the process of migrating an iPhone app to a universal app. On one of my views, I present a UIActionSheet with a UIPickerView as a subview. On the iPhone this always worked just fine. Of course, on the iPad I had to change a little to present the ActionSheet in a popover control. Here's some psuedo-code to outline where I'm at... actionSheet = [[UIActionSheet alloc] initWithTitle:nil delegate:self cancelButtonTitle:nil destructiveButtonTitle:nil otherButtonTitles:nil]; pickerView = [[UIPickerView alloc] initWithFrame:CGRectMake(0,44,0,0)]; pickerView.delegate = self; pickerView.dataSource = self; pickerView.showsSelectionIndicator = YES; [actionSheet addSubview:pickerView]; if (UI_USER_INTERFACE_IDIOM() != UIUserInterfaceIdiomPad){ [actionSheet showInView:self.view]; [actionSheet setBounds:actRect]; }else{ [actionSheet showFromRect:buttonRect inView:[UIApplication sharedApplication].keyWindow animated:YES]; } The resulting popover on the iPad is very small and only the very top of the UIPickerView is visible. How can I set the size of the popover?

  Read the article

• What is the best way to move a UIToolbar?

  - by Ferdinand Rios

  Here is an interesting problem. On the iPhone, I have a view set up that has a toolbar on the bottom of the screen. I am currently trying to make this a universal app so that it runs on iPad as well. I would like the toolbar to be at the top of the iPad screen, so in the viewDidLoad method of the specific viewController I have the following code. if (UI_USER_INTERFACE_IDIOM() == UIUserInterfaceIdiomPad) { //move the toolbar to the top of the page and move the webview down by the height of the toolbar CGRect toolBarFrame = self.aToolBar.frame; CGRect webFrame = self.aWebView.frame; webFrame.origin.y = toolBarFrame.size.height; [self.aWebView setFrame:webFrame]; toolBarFrame.origin.y = 0; [self.aToolBar setFrame:toolBarFrame]; [Utils errorString:[NSString stringWithFormat:@"origen: x=%f y=%f", self.aToolBar.frame.origin.x, self.aToolBar.frame.origin.y]]; [Utils errorString:[NSString stringWithFormat:@"origen: x=%f y=%f", self.aWebView.frame.origin.x, self.aWebView.frame.origin.y]]; } The problem I am having is that the webView moves down fine, but the toolbar only moves up to about what seems to be the height of a iPhone screen. The call to errorString tells me that the webView's origin is at 0,44 (where it should be) and that the toolbar's origin is at 0,0, but it is actually somewhere in the middle of the screen! Anybody have a clue what is going on here?

  Read the article

• Wrong Ruby Float and BigDecimal subtraction result

  - by SamChandra

  I am running: [~/ruby/rails/sas]$ ruby --version ruby 1.8.7 (2009-06-08 patchlevel 173) [universal-darwin10.0] on Mac Snow Leopard 10.6.3 Can anyone help to explain why the Float and BigDecimal subtraction can be this wrong. [~/ruby/rails/sas]$ console Loading development environment (Rails 2.1.1) >> num = 30.0 => 30.0 >> num.class => Float >> ex = 28.04.to_d => #<BigDecimal:105367e40,'0.284E2',8(8)> >> ex.class => BigDecimal >> num - ex => 1.6 >> _.class => Float >> I was hoping that the result should be 1.96, I know that perhaps doing an arithmetic operation using 2 different data types are not recommended, but this behavior is so strange. It seems to be wise that from now on, I have to check the variables data type before doing any arithmetic operation. Hopefully somebody can give me an insight on what was happening.

  Read the article

• Add new language to existing Xcode project localization

  - by leolobato

  Hey guys, I'm working on an existing Xcode 3.2.2 Universal iPhone OS project which is already localized for 4 languages (EN, IT, DE and FR). We are now adding a new language (JA) into this project. Each existing .lproj folder (en.lproj, it.lproj, de.lproj and fr.lproj) has almost 60 files - including PNGs, HTMLs and the Localizable.strings file. Each one of those files appear as localized groups inside Groups & Files in Xcode. They're spread all over the tree. If I right-click one of those groups (say, Localizable.strings) inside Xcode, Get Info, click on "Add Localization" and type "ja" - as the Xcode docs suggest, nothing happens. From what I read in this newgroup, it's possibly because of the way those folders are named. If they were named like English.lproj and Italian.lproj, this was supposed to work. So, for me to actually import a new language localized file into the existing group, I have to: Right-click the localized group file. Choose "Add Existing File". Select the corresponding file inside the ja.lproj folder. I'm about to get a new ja.lproj folder with those 60 localized files and would love to import them in the project in a way that doesn't involve searching for every single file in Groups & Trees and performing those steps... for every one of those 60 files. Is that possible? Is there a right (or better) way to import a new language into this Xcode project?

  Read the article

• What are the most interesting equivalences arising from the Curry-Howard Isomorphism?

  - by Tom

  I came upon the Curry-Howard Isomorphism relatively late in my programming life, and perhaps this contributes to my being utterly fascinated by it. It implies that for every programming concept there exists a precise analogue in formal logic, and vice versa. Here's an "obvious" list of such analogies, off the top of my head: program/definition | proof type/declaration | proposition inhabited type | theorem function | implication function argument | hypothesis/antecedent function result | conclusion/consequent function application | modus ponens recursion | induction identity function | tautology non-terminating function | absurdity tuple | conjunction (and) disjoint union | exclusive disjunction (xor) parametric polymorphism | universal quantification So, to my question: what are some of the more interesting/obscure implications of this isomorphism? I'm no logician so I'm sure I've only scratched the surface with this list. For example, here are some programming notions for which I'm unaware of pithy names in logic: currying | "((a & b) => c) iff (a => (b => c))" scope | "known theory + hypotheses" And here are some logical concepts which I haven't quite pinned down in programming terms: primitive type? | axiom set of valid programs? | theory ? | disjunction (or)

  Read the article

• UINavigationController navigation stack problems in Landscape Mode

  - by David F

  I have a iPhone application that I am currently converting to a Universal Binary to work with the iPad. I have successfully implemented everything I need in terms of layout so that full landscape functionality is now supported in my app (previously I primarily used portrait mode to display content). But, I have one strange problem, and it ONLY occurs in landscape mode: when I push a view controller onto the stack, it takes two taps on the back button to return to the previous view controller!!! The first tap shows a blank view, but with the same name on the left-side back navigation button, the second tap takes the controller back to previous view like it should. I don't have an iPad to test, so I am relying on the simulator. The problem does not show up on the iPhone and doesn't show up if you rotate back to portrait mode. My app consists of a tabbarcontroller with navigation controllers loaded for its vc's: //application delegate - (void)applicationDidFinishLaunching:(UIApplication *)application //.... WebHelpViewController *vc8 = [[WebHelpViewController alloc] init]; UINavigationController *nv8 = [[UINavigationController alloc] initWithRootViewController:vc8]; [self.tabBarController setViewControllers:[NSArray arrayWithObjects:nv1,nv2,nv3,nv4,nv5,nv6,nv7,nv8,nil]]; To implement landscape capability, the UITabBarController is overridden to autorotate when required: //CustomTabBarController.m - (BOOL)shouldAutorotateToInterfaceOrientation:(UIInterfaceOrientation)interfaceOrientation { return [[(UINavigationController *)self.selectedViewController topViewController] shouldAutorotateToInterfaceOrientation:interfaceOrientation]; } ... works fine. I navigate into new views using this method SomeViewController *vc = [[SomeViewController alloc] init]; [self.navigationController pushViewController:vc animated:YES]; [vc release]; Has anyone encountered this problem, and do they know if it's only a simulation error?

  Read the article

• rake test:units fails with status ()

  - by ander163

  New user, haven't been building tests as I go, so I'm an idiot. The application is running, but the tests fail. Here is what appears to be relevant: .... ** Execute test:units /usr/local/bin/ruby -I"lib:test" "/usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake/rake_test_loader.rb" "test/unit/event_test.rb" "test/unit/helpers/calendar1_helper_test.rb" "test/unit/helpers/events_helper_test.rb" "test/unit/helpers/homepage_helper_test.rb" "test/unit/helpers/main_helper_test.rb" "test/unit/helpers/mobile_helper_test.rb" "test/unit/helpers/notes_helper_test.rb" "test/unit/helpers/password_resets_helper_test.rb" "test/unit/helpers/projects_helper_test.rb" "test/unit/helpers/search_helper_test.rb" "test/unit/helpers/start_helper_test.rb" "test/unit/helpers/superadmin_helper_test.rb" "test/unit/helpers/tasks_helper_test.rb" "test/unit/helpers/user_sessions_helper_test.rb" "test/unit/helpers/users_helper_test.rb" "test/unit/note_test.rb" "test/unit/notifier_test.rb" "test/unit/project_test.rb" "test/unit/task_test.rb" "test/unit/user_session_test.rb" "test/unit/user_test.rb" /usr/lib/ruby/gems/1.8/gems/rails-2.3.5/lib/rails/gem_dependency.rb:119:Warning: Gem::Dependency#version_requirements is deprecated and will be removed on or after August 2010. Use #requirement /usr/lib/ruby/gems/1.8/gems/hpricot-0.6.164/lib/universal-java1.6/fast_xs.bundle: [BUG] Segmentation fault ruby 1.8.7 (2009-06-12 patchlevel 174) [i686-darwin10.2.0] rake aborted! Command failed with status (): [/usr/local/bin/ruby -I"lib:test" "/usr/loc...] /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:995:in sh' /usr/local/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:1010:incall'

  Read the article

• software distribution and patch management

  - by daemonkid

  How do software houses like Microsoft or anti-virus companies patch/update their software? Anti virus companies dont send the complete executable; only new virus signatures I suppose. Similarly, Ive noticed microsoft sends certain files to the '$NtUninstallKB......$' folder that it creates when it the windows update program runs. I suppose there is an installer in each such folder there that replaces only those dlls that need to be updated or fixed. Questions Is there a universal method for doing this or does each house employ their own methods? I dont want to re-send the entire application to each individual client. Suppose if only certain dlls need to be changed or maybe some more added, how should I go about planning my final compiled application. Do I need to look at separating my application into multiple assemblies? If yes, then is there some compilation method that is allows to pack specific classes into a particular dll? What I have put down here are my thoughts on the subject and I could be wrong. Could anyone throw some light on this please? I am looking at implementing such a deployment and patch management technique for the .net platform. Thanks for your time.

  Read the article

< Previous Page | 21 22 23 24 25 26 27 28 29 30 31 32  | Next Page >