Search Results

Search found 7463 results on 299 pages for 'personal computers'.

Page 250/299 | < Previous Page | 246 247 248 249 250 251 252 253 254 255 256 257  | Next Page >

• Single m0n0wall - Two LAN Subnets - How To Setup

  - by SnAzBaZ

  I have two LAN subnets that I need to link together they are 192.168.4.0/24 and 192.168.5.0/24 There is a m0n0wall running on 192.168.4.1. It's LAN connection goes out to our network switch, and it's WAN port goes out to our ADSL modem. WAN is connected via PPPoE. The 192.168.4.0 subnet contains all of our office workstations. The 192.168.5.0 subnet contains development servers and test machines that need to obtain internet access and be "managed" by computers on the 192.168.4.0 subnet, but need to be on their own subnet as well. I have a Draytek 2820N configured on 192.168.5.1 with it's WAN2 port configured as 192.168.4.25 and a default gateway of 192.168.4.1. Machines on the 5.0 subnet can connect to the internet via the m0n0wall just fine. I configured a static route on the m0n0wall LAN interface, Network 192.168.5.0/24 and Gateway 192.168.4.25. Machines on the 5.0 subnet can ping machines on the 4.0 network but the reverse does not work. I configured a new firewall rule on the m0n0wall that allows any traffic on the LAN interface with a source IP of 192.168.4.25 to be allowed. The DrayTek firewall is currently configured to pass all traffic regardless. When I try to ping a machine in the 5.0 subnet from 4.0 I see this in my m0n0wall log: BLOCK 14:45:27.888157 LAN 192.168.4.25 192.168.4.37, type echoreply/0 ICMP So the reply is being sent from the 5.0 subnet but is not being allowed to reach my workstation because the firewall is blocking it. Why is the firewall blocking it ? I hope the explanation of my network is clear, please ask if you require further clarification. Thank you.

  Read the article

• UDP blocked by Windows XP Firewall when sending to local machine

  - by user36367

  I work for a software development company but the issue doesn't seem to be programming-related. Here is my setup: Windows XP Professional with Service Pack 3, all updated Program that sends UDP datagrams Program that receives UDP datagrams Windows Firewall set to allow inbound UDP datagrams on a specific port (Scope: Subnet) If I send a UDP datagram on any port to other, similar machines, it goes through. If I send the UDP datagram to the same computer running the program that sends (whether using broadcast, localhost IP or the specific IP of the machine), the receiver program gets nothing. I've traced the problem down to the Windows XP Firewall, as Windows 7 does not have this problem (and I do not wish to sully my hands with Vista). If the exception I create for that UDP port in the WinXP firewall is set for a Scope of Subnet the datagram is blocked, but if I set it to All Computers or specifically enter my network settings (192.168.2.161 or 192.168.2.0/255.255.255.0) it works fine. Using different UDP ports makes no difference. I've tried different programs to reproduce this problem (ServerTalk to send and either IP Port Spy or PortPeeker to receive) to make sure it's not our code that's the issue, and those programs' datagrams were blocked as well. Also, that computer only has one network interface, so there are no additional network weirdness. I receive my IP from a DHCP server, so this is a straightforward setup. Given that it doesn't happen in Windows 7 I must assume it's a defect in the Windows XP Firewall, but I'd think someone else would have encountered this problem before. Has anyone encountered anything like this? Any ideas?

  Read the article

• Win Svr 2003 DHCP Bad Addresses

  - by VinceM

  After looking at other posts I still can figure this out. I'll start at the beginning... I inherited this network and I'm not the most knowledgeable about networking... We have a AD DHCP Server that is also our DNS server, We were having some VPN issues (on the same server) and my boss decided to disable routing and remote access, which cleared the settings. We couldn't get it set back up correctly so we rolled back to a backup drive they created a number of months ago. Since rolling back I've had Bad_Address listings in DHCP and there is a number of duplicate records in the DNS Forward Lookup Zones. We have less than 50 devices on the network but I have over 90 Bad Addresses showing. This server is currently running but we get IP address conflicts all the time on pretty much all the computers. I have had people do release and renew but it didn't help... I have also deleted and re-added the scope to no avail either. Any help or ideas would be greatly appreciated and I apologize if I missed another post that has information to help. Thanks, Vince

  Read the article

• VLAN setup on my PC

  - by Surjya Narayana Padhi

  Hi Geeks, I am bit new to VLAN. I want my two computers communicate through VLAN. I have following queries. As I am new to it my queries may be somewhat vague in some points. But i would like to hear from experts for my basic queries. I have two PCs Computer A and Computer B in two different IP networks Network A and Network B Both my PC has windows OS installed. How to send a VLAN(#Number) tagged packet from Computer A to Computer B and how to detect and untag the packet at Computer B? (Please provide the steps for windows OS) For this action do I need to check if my ethernet card supports VLAN tagging/untagging? If yes how can I know if my card supports it or not? Is the VLAN applied for Wireless ethernet controllers also? Do I need any switch or router for this action? Experts please given your inputs so that I can have a strong basic. If anyone can give some inputs how i can detect those VLAN in wireshirk, it will be helpful me also. Thanks in advance.

  Read the article

• Internet Explorer will not open

  - by KCotreau

  I recently migrated a company to a Microsoft domain environment, logged the users in under their new domain accounts, and then copied the old profiles to the new profile. I am not sure if that is related since they did not complain about it right away and it may have been a subsequent patch or something, but I have two XP computers that will not open IE8. You click on it, and it nothing graphically happens at all, but you can see a process in task manager. If you click many times, you get multiple instances. It will appear often TWICE per click. It still works in the old profile, so it is specific to the profile, and I would like to fix it rather than blow it away. Here is what I have done without success: Tried opening without add-ons (the one in System Tools) Reinstalled IE8 Ran SFC /SCANNOW I found a script that was supposed to repair any registry entries, and ran it. I tried exporting the whole HKCU\Software\Microsoft\Internet Explorer key and deleting it, hoping that when I restarted it, it would recreate it...No joy. I restored it. Any ideas?

  Read the article

• Synchronising a remote folder with a local one.

  - by Workshop Alex

  I am using a network disk (that's connected to my router by USB) to store several data files. A simple .NET application that I've created is supposed to read and modify these data files. However, some security issues are preventing this application to access these files directly. (Actually, these have been built-in to my application on purpose since it's not going to support NAS disks.) Since this disk is shared with several computers, I just want to have a simple synchronisation method, which will copy the files to a local folder where3 my application can access them. And, once modified, it should send back the modified files to the NAS disk again. I have two options: 1) Build a second application to do my own synchronisation. 2) Find some build-in function inside Windows 7 Ultimate which can do this for me. Option 2 is preferred. Option 1 is something I can do easily, if need be. I don't need third-party tools. (Still, feel free to add some references to good tools, although I won't accept them as answers.) Basically, is this possible with Windows 7 and if so, how?

  Read the article

• UDP blocked by Windows XP Firewall when sending to local machine

  - by user36367

  Hi there, I work for a software development company but the issue doesn't seem to be programming-related. Here is my setup: - Windows XP Professional with Service Pack 3, all updated - Program that sends UDP datagrams - Program that receives UDP datagrams - Windows Firewall set to allow inbound UDP datagrams on a specific port (Scope: Subnet) If I send a UDP datagram on any port to other, similar machines, it goes through. If I send the UDP datagram to the same computer running the program that sends (whether using broadcast, localhost IP or the specific IP of the machine), the receiver program gets nothing. I've traced the problem down to the Windows XP Firewall, as Windows 7 does not have this problem (and I do not wish to sully my hands with Vista). If the exception I create for that UDP port in the WinXP firewall is set for a Scope of Subnet the datagram is blocked, but if I set it to All Computers or specifically enter my network settings (192.168.2.161 or 192.168.2.0/255.255.255.0) it works fine. Using different UDP ports makes no difference. I've tried different programs to reproduce this problem (ServerTalk to send and either IP Port Spy or PortPeeker to receive) to make sure it's not our code that's the issue, and those programs' datagrams were blocked as well. Also, that computer only has one network interface, so there are no additional network weirdness. I receive my IP from a DHCP server, so this is a straightforward setup. Given that it doesn't happen in Windows 7 I must assume it's a defect in the Windows XP Firewall, but I'd think someone else would have encountered this problem before. Has anyone encountered anything like this? Any ideas? Thanks in advance!

  Read the article

• Windows 2008 R2 RDS - Double Login

  - by colo_joe

  Issue: Double logins when connecting to RemoteApps or Remote Desktop Environment: Gateway = 1 server 2008 R2 - Roles = Gateway, Session Broker, Connection Mgr, Session Host Configuration server Session hosts = 2 servers 2008 R2 - Roles = App Manager and Session host configuration Testing: I can get to the url http://RDS.domain.com/rdweb - I get prompted for authentication (1) Pass authentication, get list of remote apps. Click on remoteapps or remote desktop, get prompted for authentication again (2). Pass authentication, I get access to app or RDP. Done so far. On session host Signed rdp files with cert. Added the following to the custom RDP settings: Authenticaton level:i:0 = If server authentication fails, connect to the computer without warning (Connect and don’t warn me). prompt for credentials on client:i:1 = RDC will prompt for credentials when connecting to a server that does not support server authentication. enablecredsspsupport:i:1 = RDP will use CredSSP, if the operating system supports CredSSP. Edited the javascript file as found in http://support.microsoft.com/kb/977507 Added Connection ID, and added Web Access server to TS Web Access Computers group on the Session host servers, and Signed apps as found in hxxp://blogs.msdn.com/b/rds/archive/2009/08/11/introducing-web-single-sign-on-for-remoteapp-and-desktop-connections.aspx Note: This double login happens internally and externally.

  Read the article

• Windows Server 2008 R2 Virtual Network Setup

  - by jpearl01

  Hi all, Some background: I'm very much new to networking in general, and virtualization in particular. I'm trying to set up a series of VMs as we are transitioning to a thin client setup. I have been supplied a limited number of static ip addresses. The server is located in an offsite building which houses the network we use to connect to the internet, share folders etc. The setup I've been trying to go for is this: The host OS (Windows Server 2008 R2) is bound to one nic using one of the static ips (say, Nic1 and ip 10.255.6.61). I've set up another external virtual network attached to another physical nic , and a virtual private network attached to no nic. There is one VM running the same os (as the host). This VM is connected to both the external virtual network (and uses another static ip say Nic2 and ip 10.255.6.62) and also to the virtual private network (I gave it a static random ip 192.168.88.1 subnet mask 255.255.255.0). This virtual private network is connected to all the other VMs. I'd like to share the internet connection with all the other VMs on the private virtual network, and so I installed the RRAS role on the server connected to Nic2, and selected the option to share the internet over the vpn. I've run through the RRAS wizard a few times, trying different configurations, but none of them seem to be letting the other vms connect to the 'net. The vms seem to connect to the virtual private network fine, they are assigned an ip address and everything, but no internet, and no rest of the network either. The other problem is in general I connect to the vms with RDP. Will that be possible with a setup like this? i.e. will the vms show up as computers on the network? If not, what are my other options? Thanks! ~josh

  Read the article

• Files deleted. What could have happened?

  - by jjfine

  I'm having a weird issue today. I was writing and testing out some simple cgi scripts this morning when I realized that I couldn't run them from one of the other computers on the (windows) network. So I had my network admin come in and take a look at what was going on. A few minutes later a co-worker came in and told me that a bunch of files he was working with as well as a bunch of others (all *.c files) on the network drive got deleted. He also noticed some strange apache_dump_500.log.txt files in the same directories where the files got deleted. The apache_dump_500.log.txt files all look like this: REDIRECT_HTTP_ACCEPT=*/*, image/gif, image/x-xbitmap, image/jpeg REDIRECT_HTTP_USER_AGENT=Mozilla/1.1b2 (X11; I; HP-UX A.09.05 9000/712) REDIRECT_PATH=.:/bin:/usr/local/bin:/etc REDIRECT_QUERY_STRING= REDIRECT_REMOTE_ADDR=<my computer's local ip> REDIRECT_REMOTE_HOST= REDIRECT_SERVER_NAME=<my computer's domain url> REDIRECT_SERVER_PORT= REDIRECT_SERVER_SOFTWARE= REDIRECT_URL=/cgi-bin/trojan.py I looked and I don't have any trojan.py in my cgi-bin folder. And all my apache logs are clean. Windows event logger seems to not have any traces of what happened either. My httpd.conf: http://pastebin.com/Yny2Yh8v I think we've got some kind of virus that added this trojan.py file to my cgi-bin, ran the script, and deleted the script and any traces from the logs. Is this a thing that happens? Any ideas whatsoever would be much appreciated!

  Read the article

• How to set up simple VPN for secure Internet connections over unencrypted Wi-Fi on Windows?

  - by Senseful

  I'm looking for a solution similar to the one in this question, except that I don't have a linux computer. I have windows computers that could be set up to accept VPN connections. Preferably I want to set this up on either Windows Server 2003 or Windows XP. I'd like to connect different devices (e.g. iPhone, iPad, laptops, etc.) that are on open unsecure wireless networks (e.g. the one's you see at places like Starbucks) to this VPN to ensure that all my data is secure. I found an article that shows that you can enable VPN connections on Windows XP. After following those steps, though, I'm not sure what to do. Which ports do I open on my firewall? Which VPN settings do I use on my devices such as the iPhone? Do I use L2TP, PPTP, or IPSec? What's the difference between these? Are there any other steps missing in that tutorial? I'm hoping that since Windows has this built in feature, that it will be much simpler to set up rather than having to deal with setting up something such as OpenVPN. If I follow those settings and enable port forwarding on port 1723, and then use the following settings on the iPhone: PPTP (IP Address) RSA SecurID: Off Encryption Level: Auto Send All Traffic: On Proxy: Off It shows "Connecting..." then "Disconnecting..." and the following error message: VPN Configuration A connection could not be established to the PPP server. Try reconnecting. If the problem continues, verify your settings and contact your Administrator. I'm using a user account that I enabled privileges to in the VPN settings on the Windows machine.

  Read the article

• How to change the spell checking language in Chromium?

  - by mote

  When write I need spell checking in Danish or English (one at a time, not both at the same time), but changing from one language to the other is not working well for me. Example: Writing an email in English, everything is underlined as misspelled because the spelling language is set to Danish. I then right-click the text field and choose "Spell-checker Options" and set the language to English. But is does not change the language. Only after I try maybe 4-5 times it does. Selecting the text, clicking it, clicking the background, click the text, I have tried it all but I cannot figure out how it works. Sometimes it changes on first try, sometimes I have to do it 6-7 times. Searching brings lots of a known bugs stating that Chromium does not re-check the text after changing the language. But that is not what drives me crazy, for starters being able to change the language in the first try would be nice. It is not a fault in my installation, I have the same problem on 3 computers. Does any know something that I don't?

  Read the article

• Is there a historical computer peripherals or accessories museum or even just a current list?

  - by zimmer62

  Thinking about all the unique and different peripherals I've owned over the years, from ISA capture cards, to parallel port controlled shutter glasses for 3d games. I've seen many many accessory or computer peripherals come and go. The nostalgia of these things is a lot of fun. I tried to find some sort of historical time-line or list but what mostly turned up is computers themselves. I'm more interested in the mice, scanners, the weird adapters that shouldn't exist, short run very rare products, strange devices from computer shows in the 80's and 90's... Hardware you might find in a geeks basement that would be completely useless now, but was the coolest thing around when it was new. An example would be a drawing tablet I had for my TI-99 computer, or the audio tape player accessory for a C64 which let you save files to audio tapes, An ISA card that did the same for PC's hooked up to a VCR. Remember that IBM-PC Jr upgrade kit, that added a floppy drive, more memory and the AT switch in the back? I'd love to find either a wiki, or a list that has already been assembled which contain many of these weird (or common) accessories. I've had so many over the years I suppose I could start a wiki here if such a list doesn't already exist.

  Read the article

• Broad Band LAN connection through existing 6 wire phone line ( no phone connected )

  - by Paul Taylor

  I have an (up to but never achieved ) 10 mb broadband signal coming into my house along the telephone line. The modem then connects the broadband signal via a LAN connection and Wi-Fi signal to my computers and iPad. My workshop desk is 54 yards (approx. 50m) downhill from the modem (part of a separate building) – too far to give a good direct signal. The inside corner of the workshop (by a window) receives a weak signal. I have a disconnected telephone cable consisting of 6 wires going from the house to the workshop. The telephone is no longer used in the workshop - we use our mobile number for business calls. A broad band signal using the cable would not have to share with a phone. What would be the most economic price/efficient way to get the broadband signal to the workshop? I am writing in hope that since the telephone didn't need the six wires, an Ethernet connection might be similar and not need all the eight wires for a LAN connection. In theory could use the telephone wire to pull an Ethernet cable trough the underground pipe but I doubt if the cable would survive the strain. The broad band connection in the workshop does not have to have network facility. My skill level is high enough to do house wiring, plumbing and gas fitting; so given any sound advice and a wiring diagram or instructions I can probably work out the rest myself.

  Read the article

• w2k3 AD DC Demotion fails with "no other AD DC for that domain can be contacted"

  - by Kstro21

  i've a small office with a single w2k3 sp2 DC(bad idea, but it is real), now, i want to make a clean install of that pc, so, i got another one, install w2k3 sp2, add it to the domain, dcpromo and set it to be a GC, untill now everything is ok, then tried to dcpromo in the primary DC, but it fails with The box indicating that this domain controller is the last controller for the domain mydomain.com is unchecked. However, no other Active Directory domain controllers for that domain can be contacted. Do you wish to proceed anyway? If you click Yes, any Active Directory changes that have been made on this domain controller will be lost. So, i started to move all the roles to the new server as described here, when all was ok with the roles, i tried doing the same, but got the same result. Tried moving the DNS to the new server, but it doesn't make difference. Shutdown to the old server, then tried to log into a workstation, but it fails saying the domain is not available, also coudln't add new workstation to the domain, so i have to power on the old server again. So, if i successfully move all the roles and dns to the new server: why dcpromo give such message in the old server? why if i shutdown the old server the domain is not available?? if i successfully move all the roles and dns to the new server, and i click yes when dcpromo give warning in the old server, will i lose all users, computers, ou, etc.? am i missing some steps to make this work?? hope you can help me thanks

  Read the article

• How to kill tasks in Windows 7 when even Task Manager won't open or respond?

  - by endolith

  Occasionally one of my computers will get so bogged down that everything locks up, Ctrl+Alt+Del doesn't work, Task Manager won't open, or they work, but are opening so slowly that it will take hours or days to shut down other processes and regain control of the computer, etc. Is there a way to, for instance, force Task Manager to be highest priority so it always opens immediately with Ctrl+Shift+Esc even when some other process/driver is hogging the CPU? Is there some other program that can run in the background and open immediately like this? This question isn't about fixing "underlying problems". No matter how much memory you have, it's still possible for a rogue process to eat it all up and lock up the computer in page fault thrashing, hog the CPU, etc. This question is about how to take back control of the computer when that happens. Basically when these kind of lock-ups happen, I want to open some kind of task manager that pauses every other process and allows me to kill one of them, and then let everything resume so I can save my work, etc. Otherwise my only option is to hold down the power button. Antifreeze is supposed to do exactly what i want, pausing all other applications and starting a task manager to kill the offender, but in my testing, it actually does neither.

  Read the article

• Installed Paragon HFS+ for Windows 8, now my pc won't recognize the external firewire drive

  - by Steve

  I'm not incredibly knowledgeable about computers and I really need some help. Just got a Seagate external firewire drive this morning. I downloaded the necessary pc driver (Paragon HFS+ for Windows 8) through their website per the instructions that came with the drive. After installation, I restarted and the pc recognized the firewire drive just fine. About three hours into copying files from my pc to the firewire drive, it gave me an error and told me the files couldn't be copied. When I clicked to get out of the message, the computer crashed. After an hour of it trying to repair itself in safe mode, it restored me to an earlier version before the system crashed. Here's my current dilemma: The Paragon HFS+ is still showing up in my programs as installed, but the Device Manager is not recognizing the drive. When I try to uninstall and reinstall Paragon, it interrupts me with a message saying "The setup must update files or services that cannot be updated while the system is running" and basically gives me the finger. I have no idea what to do now, as it won't let me uninstall and reinstall Paragon, and I have no idea why it crashed my computer in the first place. Is there possibly another Mac - PC firewire driver I can try downloading instead? I really don't know what I'm doing and any help would be greatly appreciated.

  Read the article

• How to share text, pictures and video to restricted set of users

  - by joaoc

  I want to share pictures and videos of my kid growing up but I don't want it to be open to the public. I just want me and my wife to be able to add material and then share with grandparents and friends who would be given a username/password or some other solution that authenticates them. This content would preferably be available remotely over the internet or downloaded periodically to the allowed viewers computers. The second option most likely means they would have to install a client, which I am not too fond of doing (I would have to ask them to install it, help configure for different platforms, ...) I'm at the start but I would like software that also allows export of the data (if one day I want to migrate to a different solution). Folder sharing I don't know if Windows folder sharing is reliable, robust and safe enough to share over the internet. Dropbox could be a software solution, but it's limited to 2GB and requires receivers to also install and configure software. A folder is just a collection of files, so it would be harder to keep them organized with text describing the pictures/video Email I could email the content every now and then but videos are almost always too big to go as attachments This would also not provide a history of updates to anyone just recently joining in Are there other solutions to achieve this? NOTE: I also thought that software to run a local or remote blog could be an option but we aren't allowed to ask those questions on superuser because one admin doesn't like cloud-computing questions. But if you do think it's the best approach and can suggest a solution, do state it in the answers anyway!

  Read the article

• HP Photosmart C4780 printer/scanner breaks netgear WNDR3700v3 router on connection

  - by CodeJunkie

  A few months ago, we upgraded our Netgear router's firmware. Immediately, we started having trouble connecting to the internet. Each time this problem would happen, every device in the house would stop being able to make new connections to the internet. For example, you couldn't open new pages in the browser, but if Skype was running when the problem happened, you could keep talking to people. The only solution to this problem seemed to be resetting the router to factory defaults. Eventually, we solved this problem by just downgrading the router firmware. A while later, we got a new Netgear router. Almost right away, the new router started having exactly the same problems as the old one did on current firmware. The network connection would stay active and the computer would say it had an internet connection, but you couldn't do anything online except for using Skype. We eventually figured out that this happens every time our HP printer gets onto the network. Any time the printer gets onto the wireless network, the whole network stops connecting to the internet almost completely. The only thing that will fix it at that point is to reset the router to factory specs, and unplug the printer so it can't get back onto the network. The Netgear router has the latest version of the firmware, but the printer/scanner is very old. It looks to me like this problem is probably a result of a firmware conflict between the printer and the router, but I'm not sure how to fix that problem. Here's some additional information: Printer: HP Photosmart C4780 Router: WNDR3700v3 Router firmware: V1.0.0.22_1.0.17 (Stock, up to date firmware) Why would the printer getting on the network cause the router to not be able to access the internet correctly until it was reset? What can be done to allow the printer to be on the network without breaking the network for all other devices? Edit: One other thing that happens during this internet problem is that multiple computers in the house display an "IP conflict" message repeatedly, and extremely frequently (as often as every five to ten minutes, and every time a connection to the wireless is made).

  Read the article

• Setting up xpra for client use in OS X

  - by Jonathan

  I've been trying to get xpra to run on OS X for the last few days to connect to my Ubuntu server. Note that there's a GUI for it called shifter, but that (at least on OS X) is still far too buggy. For those who don't know what xpra is, if you know what screen is, it's like screen for GUI X Windows apps tunneled over ssh. You can render a remote X app locally so it's faster than sending a series of compresses screen shots (like VNC), but with xpra you can disconnect and reconnect on different computers. To get the basic functionality you can just type "ssh -X server.location" and any GUI app you open from the command line will open locally. I've been able to get xpra to build by doing the following: Download pari-all-0.0.6.tar.gz from the xpra site listed under upstream and untar it. Issue the following Mac Ports command (Dependencies thanks to RogBlog): sudo port install python25 python26 py26-pyrex py26-gtk xorg-libXtst py25-gobject py25-gtk py25-nose py26-nose xorg-libXdamage xorg-libXcomposite xorg-libXtst xorg-libXfixes In the upstream list of v0.0.06 patches (NOT 0.0.8pre!) on the xpra site listed above, download mswindows-conditional-pyrex.patch. Open the patch with your favorite text editor and change the single occurrence of "win" in it to "darwin". Apply the patch to setup.py. Run do-build in the command line. Now where I'm stumped: how do I run xpra? The build produces a sub directory called install/bin in which xpra is located, but when I try to run it I get the following error: Traceback (most recent call last): File "./xpra", line 4, in import xpra.scripts.main ImportError: No module named xpra.scripts.main There is a file called main.py under xpra/scripts, but I don't know any python and I'm not sure if this is what it's looking for, and what to do with it even if it is. My goal is to set up xpra so I can install it into /usr/bin (or some other common path for executables) and execute it whenever I please. What do I do next?

  Read the article

• Connecting to unsecured wireless network

  - by Sanchez

  I would like to know what information is public and can be intercepted in a non-open, but unsecured wireless network. Moreover, is there anything I can do to make it more "secure", other than using https connection whenever possible. In more details, I recently discovered (with surprise) that the wireless network in my school is actually unsecured. Although not everyone can connect to it (you need a student ID), I am told that certain softwares like Wireshark would be able to intercept the data. Since I have been using the network for all private purposes (email, facebook etc), I do feel quite insecure now and would like to understand the situation a bit better. I installed Wireshark and tried to play with it but all I can see are something alien to me. In any case, all I see seems to come directly/indirectly from my IP address, and I have long thought that usually different computers in the same wireless network would be assigned different addresses. Am I wrong? If not, then I feel very confused about what information is actually being captured (potentially by other users in the network, since I don't think I could capture activities of others in the same network anyway), and whether it's safe to use the network at all. (Gambling on others in the same network showing good behaviour is apparently not an option.) Thank you.

  Read the article

• Windows 7 starts getting sluggish over a few days

  - by munrobasher

  Myself and the other developer are running Windows 7 Enterprise 64 bit with 8GB RAM on different Gigabyte motherboards with Quad core Intel CPUs. Most of the time, it runs like a dream. We use VMware workstation a lot (hence the 8GB) and that works well. Except... now and then, after the PCs have been on for a few days, the whole system starts getting really sluggish doing certain tasks. The other's developer's system is far worse than mine with it taking up to a minute to launch IE. Today, mine has gone sluggish but nowhere near as bad. For example, normally when I click on a new tab in IE, it's instant. Today, there's an obvious delay. Right-clicking in this window to trigger iSpell is normally instant, right now it takes about five seconds. I've got resource monitor open on my second monitor and when I did that right-click, there was no obvious peak in CPU, disk or memory. A reboot does fix it so it does sound like a resource issue but haven't a clue what might be to blame. The two computers have similarities (same spec) but also differences (like motherboard, RAM & CPU models). So I guess the question is, any pointers on diagnosing why a PC is sluggish? What could cause such a right-click slow down in IE for example? It sounds like such a simple operation. NOTE: whilst typing this message alone, it was fine performance wise. I can click around the page no problem but right-click still is noticeable slow. Will reboot over lunch... Cheers, Rob.

  Read the article

• ActiveDirectory user files aren't being shared? [on hold]

  - by Ryan

  I'm taking a class in college and my current project is to setup Active Directory. So I have two VMs, one is Windows Server 2008 R2 and the other is Windows 7. I setup the domain team15.net (this is the FQDN for the forest) on the W2008 server machine. And then I connected the Windows 7 machine to the team15.net domain, and now I can login to the administrator account on the W2008 machine by using TEAM15\Administrator for the username. However, any files that I add in Windows 7 while logged into TEAM15\Administrator are NOT shown in the Windows 2008 machine. Is this normal? It seems like any files I add to this user in the domain only exists for the machine that I'm currently using. Is it possible to change this so all files for all users are synced to all computers in the domain? If not then what are alternatives? I noticed that back in high school we also used domains but there was a shared drive E:\ that you had to store your files because if you put them on in the desktop instead then they would suddenly disappear once you logged out and back in. How can I setup a shared drive? and which computer would provide the storage for this drive?

  Read the article

• Regarding AD Domain controllers and remote branch offices

  - by Alex

  We have central HQ building and a lot of small branch offices connecting via VPN and want to implement AD (If you can believe we still haven't). We want everyone to log in using domain accounts and be policed centrally. We are OK with having a RODC in a branch office with like 10 computers. But we have these small branches with two to four PCs only. Some of these branches connect to HQ via IPSec site-to-site VPN, some via remote access (client-based) VPN. So there is no problem with ones that have local RODC or connecting to HQ DCs via VPN router. But how about small branches? We don't really want to set up a machine there, neither we want to invest into Windows Server licenses or fancy network equipment. Also, the problem is that we cannot access HQ DCs via VPN because we are not logged in and connected to HQ internal network yet, so DCs aren't reachable. What is typically done in that situation if it is needed to have central management over policies on those PCs? Or is it better to let 'em loose and use local policies and accounts in this situation?

  Read the article

• Is there a list of Windows services that can be turned off to save resources?

  - by scunliffe

  Every time I open up my task manager and look at the tasks running, it appears to me that there has got to be a bunch of junk running in there that I don't want or need and would be better off turning off (e.g. set the service to manual vs. automatic) In particular I'm running Windows XP, but I'd be interested in services for any version. e.g. Service: ThinkPad PM Service What is it: The ibmpmsvc.exe process is installed by default on IBM Notebook computers. It allows various functions of your IBM notebook to be controlled using the blue Fn keys. If you use the blue Fn keys on your Notebook, you should leave this process running. Otherwise, if it is causing problems for your system you should terminate the ibmpmsvc.exe process. (source) Thus for me, (having never used, or intending to use these buttons) - I want to turn it off. There's lots that just seem painfully unnecessary to me... I'm just not sure which ones I can "safely" stop/disable without issues... "Alerter", "ClipBook", "Messenger", "Telnet", "ATI Hotkey Poller", "Office Source Engine", etc. I'd appreciate any info on services that are truly unnecessary, or only useful to certain people/types of users.

  Read the article

< Previous Page | 246 247 248 249 250 251 252 253 254 255 256 257  | Next Page >