Search Results

Search found 21317 results on 853 pages for 'address bar'.

Page 251/853 | < Previous Page | 247 248 249 250 251 252 253 254 255 256 257 258  | Next Page >

• Centos VM serving multiple public IP: how to configure network interface?

  - by Glasnhost

  I have a Centos 5.6 VM (Vsphere client) already responding to two different public IPs on eth0 and eth0:1 and I'm trying to add eth0:2. I copied the eth0 config file and restarted the network service. I don't understand which other steps are needed... ifconfig eth0 Link encap:Ethernet HWaddr 00:40:46:B9:00:41 inet addr:10.1.12.10 Bcast:10.1.12.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:163371837 errors:77 dropped:0 overruns:0 frame:0 TX packets:168210961 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1891221045 (1.7 GiB) TX bytes:855899500 (816.2 MiB) Interrupt:59 Base address:0x2000 eth0:1 Link encap:Ethernet HWaddr 00:40:46:B9:00:41 inet addr:10.1.12.11 Bcast:10.1.12.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:59 Base address:0x2000 eth0:2 Link encap:Ethernet HWaddr 00:40:46:B9:00:41 inet addr:10.1.12.12 Bcast:10.1.12.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:59 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:188976973 errors:0 dropped:0 overruns:0 frame:0 TX packets:188976973 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2015642664 (1.8 GiB) TX bytes:2015642664 (1.8 GiB) more /etc/resolv.conf nameserver 10.1.12.1 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.1.12.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 10.1.12.1 0.0.0.0 UG 0 0 0 eth0

  Read the article

• openvpn in a bridge?

  - by sebelk

  I have a somewhat tricky proble to solve. We have a wireless link between 2 building. One of them has an mikrotik and below there are some vlans. Some machines of one vlan need to use openvpn to connect to a remote private lan. I put a TP-Link WR1043ND (which those machines connect to) with openwrt with ebtables just in case I need it. I've configured openwrt in such a way that all ports belongs to the same vlan. My idea was to make things as transparent as I can. It has a bridge as follows: usr/sbin/brctl-full show br-lan bridge name bridge id STP enabled interfaces br-lan 8000.f8d111565716 no eth0.1 eth0.2 Also I've added an ebtables rule: ebtables -t broute -A BROUTING -p ipv4 -j DROP So "bridge" has only one IP address. I've installed openvpn and I'm trying to bring up the tunnel but I can't still get working. Sure, someone can says why don't you use the vpn on the mikrotik, there are some reasons, the first one is I have little experience with mikrotik and I'd want to have the vpn at hand :) The problem is that openvpn is not working, because it is complaining that I have only one Ip Address on the server side. So I set up and alias interface with another IP address but is not working either: : Rejected connection attempt from IP-Client-Side:37801 due to --remote setting Is there a way to make it work?

  Read the article

• How can I make Chrome work more like Firefox?

  - by rhooligan

  After Firefox broke my add-ons yet again, I decided to give Chrome a second look. To my surprise all the add-ons are available. What I am missing though is the drop-down search bar. First, I've disabled the search from the location bar. Now I want to add a combo box that is always visible where I can select the engine to do searching. I downloaded a search extension (Search Box), but it's an icon that needs to be clicked before you can interact with it: TL;DR; I want a box that is always visible and can change the search engine from a drop-down. Is there an extension like this available in Chrome?

  Read the article

• ASA 5505 VPN setup. VPN works but still unable to reach devices in the inside network.

  - by chickenloop

  I've setup a Remote Access VPN on my Cisco ASA 5505. I'm able to connect to my ASA via my phone or the Cisco client, but I'm unable to reach devices in my inside LAN when connected via VPN. The setup is the following: Inside Network : 10.0.0.0/24 VPN_POOL: 172.16.0.0/24 Outside Network: 192.168.1.0/24 ASA is not the perimeter router, there is another device on the 192.168.1.0/24 network which is connected to my cable provider. Obviously UDP port 500 and 4500 are forwarded to the ASA's outside interface. Everything works perfectly, besides the VPN stuff. Config: interface Vlan1 nameif inside security-level 100 ip address 10.0.0.254 255.255.255.0 interface Vlan2 description Outside Interface nameif outside security-level 0 address 192.168.1.254 255.255.255.0 object network VPNPOOL subnet 172.16.0.0 255.255.255.0 object network INSIDE_LAN subnet 10.0.0.0 255.255.255.0 Then the exempt NAT rule. nat (inside,outside) source static INSIDE_LAN INSIDE_LAN destination static VPNPOOL VPNPOOL I don't think that the problem is with the VPN config, as I can successfully establish the VPN connection, but just in case I post it here: group-policy ZSOCA_ASA internal group-policy ZSOCA_ASA attributes vpn-tunnel-protocol ikev1 split-tunnel-policy tunnelspecified split-tunnel-network-list value Split-Tunnel default-domain value default.domain.invalid tunnel-group ZSOCA_ASA type remote-access tunnel-group ZSOCA_ASA general-attributes address-pool VPNPOOL default-group-policy ZSOCA_ASA tunnel-group ZSOCA_ASA ipsec-attributes ikev1 pre-shared-key ***** Any ideas are welcome. Regards.

  Read the article

• Win 7: How can I resize a window to make it much bigger than my screen?

  - by RexE

  I have a window that I'd like to make much bigger than my physical screen (explanation of why below). I hit Alt+Space, M, and then press the Up arrow to move the title bar above the physical top of my screen. However, when I press Enter to set it, the title bar snaps back to the top of my screen. How can I prevent this from happening? Background: I want to get a hi-res image of a neighborhood map so that it can be printed to a poster. Google Earth has a "Save as JPG" feature, which will save the map in the window to a file. The bigger the window, the bigger the JPG; so, I'm trying to make the window as big as I can. Alternate suggestions welcome.

  Read the article

• Java Applets fail to launch in Windows 7 64bit

  - by Steve

  Hi can you help? I'm having great trouble launching Java applets using Windows 7 64 bit. I have the 32 bit version of Java installed (as recommended, for use with 32 bit browsers). When I click on an Java applet to open it the Java logo shows with a circular progress bar, but the process goes no further, just the progress bar going round and round. There are no error messages. The computer is a few months old and Java has never worked properly. I've tried with both IE9 and Chrome, followed the suggested fixes, uninstall then reinstall, check certain browser settings (all were in order), check Java control panel settings (again all was in order) delete the internet cache etc, tried 32bit & 64bit Java side by side. All to no avail. I'm baffled Is there anything else to try, or do I have to accept a computer without Java (Very inconvenient!) Thanks

  Read the article

• Better urls for this internal web server?

  - by sprugman

  I've got a server that I have admin access to, but don't fully manage. (I think it's a virtual machine, but I'm not 100% sure. It's running Apache on Windows Server 2003.) I share the ip with another user, so my sites all have to use the :8080 port. This is kind of ugly. Also, AFAIK, the only access I have is through an ip address. (I'm inside a corporate firewall and don't think I have access to a DNS server or anything.) I've adjusted my hosts file so I don't have to use the ip address on my local machine, but that's not a very generic solution. Are there any options to 1) get rid of the port requirement 2) be able to use a name (maybe a machine name) instead of the ip address in a generic way? (I'm not really a network admin -- I'm a developer managing this machine. The IT folks who really manage it are a few people away from me and tough to get to do anything, so I'm looking for a light-weight solution if possible.)

  Read the article

• How can I determine the IP addresses allocated by DHCP on a router that I'm connected to?

  - by user234831

  This "router" is not a typical situation. I'm using my phone as a hotspot and can only configure a select number of DHCP options. I can manage the limit on how many devices/clients can use my phone as a hotspot. I have to select from a radio-button list with the options: 2,3,4,5, or 8 I can specify the DHCP starting IP address. In this case, it begins at 192.168.6.106 When I'm connected via WIFI to my phone, an ipconfig /all command shows me that the default gateway is 192.168.6.1 and my IPv4 address is 192.168.1.148. I have the luxury of connecting another device to the phone and that device was assigned 192.168.1.121. I've tried connecting to 192.168.6.1, hoping for some sort of router setup page that I'm used to seeing, but there is no such thing or maybe it's just a matter of incompatable operating systems. In summary, the "router" (phone) has an IP address of 192.168.6.1 and a DHCP server that begins at 192.168.6.106 and allows up to 8 connections. Normally, I would assume a range of 192.168.6.106 - 192.168.6.113, but connected clients are showing otherwise. How can I figure out which IP addresses are set aside by DHCP for clients?

  Read the article

• URI Rewrite with fake subdomains and multiple variables

  - by Rich

  Can someone please help with trying to use mod rewrite so foo.domain.com is rewritten to domain.com/p.php?s=foo and foo.domain.com/bar to domain.com/p.php?s=foo&p=bar? Currently my .htaccess is: RewriteEngine On # Remove www RewriteCond %{HTTP_HOST} ^www.domain.com$ [NC] RewriteRule ^(.*)$ http://domain.com/$1 [R=301,L] # Rewrite subdomain etc. RewriteCond %{HTTP_HOST} ^(.*)\.domain\.com$ [NC] RewriteRule ^([^/]+)/?$ p.php?s=%1&p=$2 [QSA,L,NC] But I can't work out how to grab the second variable (being optional and after a slash at the end of the URI. I've tried changing the end of the condition to ?/(.*)$, but to no avail and my mod rewrite skills are certainly naff!

  Read the article

• Running Tor relay on personal server: can this hurt?

  - by rxt

  I would like to install TOR as relay on a hosted personal server. I have loads of bandwidth that I don't use. It's not an exit point. Can this hurt my server somehow? Possible problems I'm thinking of are blacklisting the IP-address, or something similar. I know that exit points get blacklisted on many servers. So if I'm using Tor as a client, I will probably use a blacklisted IP-address for the outside world, so cannot access those sites. However, I'm running this on a server, and as a public relay. Could this hurt the functioning of and access to websites on this server? I could install it as a bridge. I'm a little confused about the difference between bridging and relaying. If I understand correctly the only difference is that a relay is public. Does this mean that bridging only works if I know someone and give them my IP-address?

  Read the article

• Windows Server 2003 VPN and Local network

  - by depo

  I have some problems reaching local network , where VPN Windows 2003 server stands. I have a network, which has a VPN server (LAN ip 10.0.0.201). I created a VPN server on that server with different subnet for VPN users (10.0.5.0). After VPN connection is initiated , i am able to acces only 10.0.0.201, but not other PC, which belongs to that network ( all i need to access 10.0.0.203 and 10.0.0.208). I think i need to add somethink to static route table, or not? C:\Documents and Settings\Administratorroute PRINT IPv4 Route Table Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.0.0.254 10.0.0.201 10 10.0.0.0 255.0.0.0 10.0.0.201 10.0.0.201 10 10.0.0.201 255.255.255.255 127.0.0.1 127.0.0.1 10 10.0.5.1 255.255.255.255 127.0.0.1 127.0.0.1 50 10.255.255.255 255.255.255.255 10.0.0.201 10.0.0.201 10 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 224.0.0.0 240.0.0.0 10.0.0.201 10.0.0.201 10 255.255.255.255 255.255.255.255 10.0.0.201 10.0.0.201 1 Default Gateway: 10.0.0.254 Persistent Routes: None C:\Documents and Settings\Administratoripconfig /all PPP adapter RAS Server (Dial In) Interface: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : WAN (PPP/SLIP) Interface Physical Address. . . . . . . . . : 00-53-45-00-00-00 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 10.0.5.1 Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : Ethernet adapter Local Area Connection 2: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Intel(R) PRO/1000 MT Network Connection Physical Address. . . . . . . . . : 00-0E-0C-3D-C9-51 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 10.0.0.201 Subnet Mask . . . . . . . . . . . : 255.0.0.0 Default Gateway . . . . . . . . . : 10.0.0.254 DNS Servers . . . . . . . . . . . : 127.0.0.1 Primary WINS Server . . . . . . . : 10.0.0.201 NetBIOS over Tcpip. . . . . . . . : Disabled VPN Client PPP adapter VPN Connection 2: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VPN Connection 2 Physical Address. . . . . . . . . : DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 10.0.5.4(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 10.0.0.201 Primary WINS Server . . . . . . . : 10.0.0.201 NetBIOS over Tcpip. . . . . . . . : Enabled

  Read the article

• A server which uses 2 IPs and is needed to give service (under NAT)

  - by user6004

  I have an internal server, which uses a certain service. This service listens on a port, and speaks on a different port. The problem with the service is that it can't listen and speak on the same IP address, so I have configured 2 IP addresses for that NIC, and so I "solved" the problem with the listening and speaking. I have a problem though... I need that server to be NATed, with a public IP address, and that server needs to be available from the outside (and as only one IP)... The question is, how do I solve the situation here? If I do a NAT for one IP address (the listening port), then he will be able to get requests from the outside, but won't be able to send out traffic (because the other IP won't have NAT). If I do NAT on both of the IPs, then when traffic comes in for the listening port, it won't necessarily arrive to the listening IP, but rather to the speaking one. I hope I made myself clear and that there is a sensible solution here that I am missing.

  Read the article

• Configuring iPad Mail app & Gmail app with different accounts? [migrated]

  - by Steve Crane

  I prefer to use the Gmail app over the standard Mail app on my iPad for reading my personal Gmail (I delete a lot of mails, newsletters, etc., after reading and this is one tap in Gmail and several in Mail). I have them set up so my personal Gmail uses the Gmail app and my work email is set up to use the standard Mail app. This all works fine except for one problem. If I'm in Gmail or Mail and send an email it sends from the relevant email address as expected. My problem is that when I share something via email from Safari or another app it sends from the email address configured in Settings for Mail (the work one) and I would prefer to do such sharing from my personal email address. Does anyone know if there is a way to achieve this? I could switch the addresses to use the other app but as I never delete work email and delete personal mail at least 50% of the time, the behaviour of the apps is perfect the way I have them set up; if only I could solve that one little problem of controlling where shared items are sent from. I am using an iPad 2 with iOS 5.1 should that be relevant.

  Read the article

• Application got shut down in WinXP if I close the 2nd window of that application.

  - by kinopyo

  I'm using WinXP and here is my question: I run an application, such as Chrome, there would be one app in the task bar, and it's fine. Suppose a new window of Chrome opened(so there would be 2 window and 2 in the task bar), and when I close that,the 2nd one, the whole application just shutdown. And so does chrome, firefox, evernote, Becky!(the email client), even TortoiseSVN. So I think there should be a generic problem cause these applications shutdown, such as the platform - WinXP. Please give me some advice or hint, anything comes to your mind would be helpful!

  Read the article

• How can I get Solr listening on 0.0.0.0 instead of just localhost?

  - by Neil

  I'm trying to get Solr to listen on 0.0.0.0 instead of just localhost, and it doesn't seem to be picking up the configuration options. I downloaded apache-solr-1.4.1 from the Solr website, and I'm running: user@:apache-solr-1.4.1/example $ java -jar start.jar With these configuration options: <Call name="addConnector"> <Arg> <New class="org.mortbay.jetty.bio.SocketConnector"> <Set name="host"><SystemProperty name="jetty.host" default="0.0.0.0" /></Set> <Set name="port"><SystemProperty name="jetty.port" default="8983" /></Set> <Set name="maxIdleTime">50000</Set> <Set name="lowResourceMaxIdleTime">1500</Set> </New> </Arg> </Call> Where the only line changed from the default is this one: <Set name="host"><SystemProperty name="jetty.host" default="0.0.0.0" /></Set> And when I check netstat, I see this: $ netstat -an | egrep 'Proto|\b8983\b' Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 127.0.0.1:8983 0.0.0.0:* LISTEN tcp6 0 0 ::1:8983 :::* LISTEN Where Local Address should be 0.0.0.0:8983 instead of 127.0.0.1:8983. Does anyone know why this might not be working?

  Read the article

• Linux: Three default gateways?

  - by Daniel

  My server has three default gateways, how can that be? Shouldn't there be one default gw? I have three NICs, each attached to a separate subnet: server1:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.5.0.0 * 255.255.255.224 U 0 0 0 eth3 localnet * 255.255.255.224 U 0 0 0 eth0 192.168.8.0 * 255.255.255.192 U 0 0 0 eth1 default 10.5.0.1 0.0.0.0 UG 0 0 0 eth3 default 192.168.8.1 0.0.0.0 UG 0 0 0 eth1 default 10.1.0.1 0.0.0.0 UG 0 0 0 eth0 Sometimes, I can't ping a host on the Internet, sometimes I can. What I want is traffic to the Internet (0.0.0.0) routed through a specific NIC. Can I just add a route for 0.0.0.0 and default gw to one of the eth0-3 interfaces? Will it break my connection? I'm using Debian, here is my /etc/network/interfaces: # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 iface eth0 inet static address 10.1.0.4 netmask 255.255.255.224 network 10.1.0.0 broadcast 10.1.0.31 gateway 10.1.0.1 allow-hotplug eth1 iface eth1 inet static address 192.168.8.4 netmask 255.255.255.192 network 192.168.8.0 broadcast 192.168.8.63 gateway 192.168.8.1 allow-hotplug eth3 iface eth3 inet static address 10.5.0.4 netmask 255.255.255.224 network 10.5.0.0 broadcast 10.5.0.31 gateway 10.5.0.1

  Read the article

• VMware ESX Linux Guest Customization

  - by andyh_ky

  Hello, I am interested in deploying several RHEL 4 Update 8 virtual machines for creation of a test environment. Here are the steps I am taking: In off hours, P2V/V2V the production machines and convert them to templates Deploy the virtual machines with a customization specification that changes hostname, IP address I am interested in how these processes are done and if there are any options for further customization. Are the machines brought on the network when they are powered on, before they are reconfigured? Is there a potential IP address conflict? Is there an option to run additional scripts which reside on the guest as a part of the reconfiguration? For example, restoring an Oracle Database. This is an option with Windows guests and sysprep, but I have been unable to locate anything showing a RHEL equivalent. I am dealing with a multi tier application. The main issue I am attempting to mitigate is that the application servers reference database servers by hostname and in tnsnames files. I am interested in scripting the reconfiguration of the application in the deployment so that the app/db servers are pointing to the test environment. I am OK with placing the 'cleanup' script on the source and executing it after the machine has been brought up. I am interested in the automation of the script's execution post clone/boot, as well as if there could be an IP address conflict. (cross posted to VMTN's ESX 4 community)

  Read the article

• Incoming traffic while on public network

  - by zvikico

  I'm developing a web app and I need to be able to get incoming traffic from 3rd party services I use. This is a classic webhooks situation: I send a request with a return address and receive the response (via HTTP) some time later to the given address. The simple solution would be to provide my external IP address and forward the incoming traffic from the router to my machine. However, I'm working in a large office and I cannot control the router configuration. I'm looking for a different way to achieve that. I do have servers online. I can have a daemon running on one of those servers, which will handle the incoming traffic. I can run a parallel daemon on my machine, which will keep an open connection with the remote daemon (over ssh preferred) and when an inbound traffic is received by the remote, it will send it to the local, which will send it to the correct port on my machine, as if it was received in the natural way. Is there any ready-made solution for that? PS. I'm on OS X and my server is Ubuntu. Thanks, zvikico

  Read the article

• How to bring back a far right chromeless window?

  - by Click Ok

  Accidentally some windows goes far right, and "goes out of" to the monitor. I know keyboard shortcuts to move it back when the windows have a title bar. But that windows (HTC Home and Rainlendar) don't have title bar, doesn't appears in windows TaskBar or TaskManager. I've tryed restart windows; to close and reopen that software; change the resolution to very low, and then to very high; but it doesn't works... I know that I can dig in the settings files of that programs, but I think interesting discover how to bring back that windows so I can use that technique if that problem appears again with another softwares too. Thank you!

  Read the article

• How Do I Get To Preferences In FireFox

  - by user123

  I'm currently trying to get to preferences in FireFox in Linux Ubuntu. Because I don't have 10 reputation, I can't post an image (otherwise I would). All I see in the browser is the Address Bar, Downloads and Home. If I right-click (or left click) on any of these, I don't have further options (other than Home, but it only allows me to add items to the toolbar, none of which are Preferences/Options/Etc). I tried vising a website to see if more options would open; nothing. I tried right clicking on the main page and each toolbar item (listed) to see if there was another options like "Preferences" or "Options"; nothing. I tried entering "Preferences" in the address bar, thinking maybe it would open automatically; nothing. I tried right clicking on FireFox on the Linux Menu to see if I could open options without opening the program (and tried this even when the program was open); nothing.

  Read the article

• What is wrong with my home network? (Routing and connection issues)

  - by David

  I have a corporate laptop that was provided to me by a client and I'm having some rather odd difficulties with it when I put the laptop on my home network. When I first brought the machine home it behaved like any other laptop. Once it was connected to the network it was assigned an IP address and I could remote into it just fine using the machine name. Lately though, whenever I put this laptop on my network I am not able to ping or RDP into the machine as the host name doesn't properly resolve. Additionally I'm able to see the device and it's assigned IP address clearly in my router firmware. This gets even more strange as now when I try to ping it's IP address listed in my router, I see that it's actually trying to ping my own machine (screenshot of this very odd event below). This has actually driven me crazy to the point that I have actually replaced my router (it was behaving oddly in other ways), and I'm continuing to have these problems. The above ping capture is from the new router. As far as network goes I am now currently using an NetGear R7000 Nighthawk and I haven't customized any of the networking settings in the router just yet (installed yesterday). I would appreciate any advice possible and would be happy to provide further diagnostic information. Networking isn't my strong suit, so I'm not even sure where to begin unraveling this thing.

  Read the article

• Application got shut down in WinXP if I close the 2nd window of that application. [closed]

  - by kinopyo

  I'm using WinXP and here is my question: I run an application, such as Chrome, there would be one app in the task bar, and it's fine. Suppose a new window of Chrome opened(so there would be 2 window and 2 in the task bar), and when I close that,the 2nd one, the whole application just shutdown. And so does chrome, firefox, evernote, Becky!(the email client), even TortoiseSVN. So I think there should be a generic problem cause these applications shutdown, such as the platform - WinXP. Please give me some advice or hint, anything comes to your mind would be helpful!

  Read the article

• merge pieces of file together

  - by veilig

  I have a directory tree of files I need to loop through and reformat the lines. can I do this with sed with some combination of find? for each file, I'll need to adjust the text in the file from ... * @category Foo * @package Bar ... into just this (Remove the @category line, but prepend the value to the package annotation value) ... * @package Foo/Bar ... what is the most efficient way of doing this? its a few hundred files that will be modified.

  Read the article

• What happened to the ability to go back in a already-loaded YouTube video?

  - by Chelonian

  For many years, my experience with YouTube had been, consistently and on any computer/browser, that once a section of that video were loaded, or the whole video, if you wanted to see an earlier part of the video again, you could simply click on the loading bar to that area and you would instantly go to that part. More recently (6 months?) this has changed. Now, clicking in an earlier part of the video forces a reload of the whole video (that is, the grey bar goes back to 0) and you have to hope your loading will be fast enough to make waiting to watch it again even worth it. It is a huge regression in usability for me. Is there any way to watch YouTube videos in the "old way"? I use Firefox 17.0.1 at this point and have an updated (I think) Flash, but I'd be willing to try other browsers or versions if it made a difference.

  Read the article

• How can I push a git repository to a folder over SSH?

  - by Rich

  I have a folder called my-project inside which I've done git init, git commit -a, etc. Now I want to push it to an empty folder at /mnt/foo/bar on a remote server. How can I do this? I did try, based on what I'd read: cd my-project git remote add origin ssh://user@host/mnt/foo/bar/my-project.git git push origin master which didn't seem right (I'd assume source would come before destination) and it failed: fatal: '/mnt/boxee/git/midwinter-physiotherapy.git' does not appear to be a git repository fatal: The remote end hung up unexpectedly I'd like this to work such that I don't have to access the remote host and manually init a git repository every time ... do I have to do that? Am I going down the right route at all? Thanks.

  Read the article

< Previous Page | 247 248 249 250 251 252 253 254 255 256 257 258  | Next Page >